STEEL DRIVER SERIES

Operation, Maintenance, and Parts Manual for SHBN4

BRAD NAILER

Specifications

MODEL SHBN4

AIR INLET ........................................................ 1/4" NPT

WEIGHT ........................................................... 2 lbs. 10 ozs.

LENGTH ........................................................... 7.9"

HEIGHT ............................................................ 7.5"

MAXIMUM PRESSURE ................................... 125 PSI

PRESSURE RANGE ........................................ 65-100 PSI

FASTENER LENGTHS ..................................... 1/4" - 1 1/4"

MAGAZINE CAPACITY ................................... 100 Brads

SCFM REQUIRED @ 90 PSI ........................... Every 10 Fasteners

Delivered Per Minute

Requires .28 SCFM

MINIMUM COMPRESSOR HP

REQUIRED TO OPERATE ............................... 3/4 HP

(TANK MOUNTED)

This manual contains information that is important for you to know and understand.

This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT

PROBLEMS. PLEASE READ THIS MANUAL.

DeVilbiss Air Power Company • 213 Industrial Drive • Jackson, TN 38301-9615

MGP-SHBN4-1A 9/25/97

TABLE OF CONTENTS

PAGE

Tool Specifications ....................................................................................... Front Cover

Table of Contents .................................................................................................... 2

Limited Warranty ..................................................................................................... 3

Safety Guidelines .................................................................................................... 4

Warning Chart ......................................................................................................... 4-6

Lubrication and Maintenance .................................................................................. 7-8

Recommended Hook-up ......................................................................................... 8

Contact Trip Safety Mechanism ............................................................................... 9

A. Operating A Contact Trip Tool

B. Checking The Operation Of Contact Trip Safety Mechanism

Loading The Tool ................................................................................................. 10

Operating the Tool ................................................................................................ 10-11

Clearing A Jam From The Tool............................................................................. 11

Trouble Shooting Guide ....................................................................................... 12

Exploded View ..................................................................................................... 13

Parts List ............................................................................................................. 14

Parts Kits ............................................................................................................. 14

Fasteners ............................................................................................................. 15

Toll-Free 800 Number ................................................................................. Back Cover

2

LIMITED WARRANTY

ONE YEAR FROM DATE OF PURCHASE

All merchandise manufactured by DeVilbiss Air Power Company is warranted to be free of defects in workmanship and material which occur during the first year from the date of purchase by the original purchaser (initial user). Products covered under this warranty include: air compressors, *air tools, accessories, service parts, pressure washers, and generators used in consumer applications (i.e., personal residential household usage only).

Air compressors, *air tools, accessories, service parts, pressure washers, and generators used in commercial applications (income producing) are covered by a 90 day warranty.

DeVilbiss Air Power will repair or replace, at DeVilbiss's option, products or components which have failed within the warranty period. Repair or replacement, and service calls on 60 and 80 gallon air compressors, will be handled by

Authorized Warranty Service Centers and will be scheduled and serviced according to the normal work flow and business hours at the service center location, and depending on the availability of replacement parts.

All decisions of DeVilbiss Air Power Company with regard to this policy shall be final.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

RESPONSIBILITY OF ORIGINAL PURCHASER (Initial User): o Retain original cash register sales receipt as proof of purchase for warranty work.

o Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s).

o Deliver or ship the product to the nearest DeVilbiss Air Power Authorized Warranty Service Center.

Freight costs, if any, must be paid by the purchaser.

o Air compressors with 60 and 80 gallon tanks only will be inspected at the site of installation. Contact the nearest

Authorized Warranty Service Center, that provides on-site service calls, for service call arrangement.

o If the purchaser does not receive satisfactory results from the Authorized Warranty Service Center, the purchaser should contact DeVilbiss Air Power Company.

THIS WARRANTY DOES NOT COVER: o Merchandise sold as reconditioned, floor models and/or display models. Any damaged or incomplete equipment sold "as is".

o Merchandise used as "rental" equipment.

o Merchandise that has become inoperative because of ordinary wear, misuse, freeze damage, use of improper chemicals, negligence, accident, improper and/or unauthorized repair or alterations including failure to operate the product in accordance with the instructions provided in the Owners Manual (s) supplied with the product.

*Air Tools: O-Rings and driver blades are considered ordinary wear parts, therefore, they are warranted for a period of 45 days from the date of purchase.

o An air compressor that pumps air more than 50% during a one hour period is considered misuse because the air compressor is undersized for the required air demand. Maximum compressor pumping time per hour is

30 minutes.

o Merchandise sold by DeVilbiss Air Power which has been manufactured by and identified as the product of another company. The product manufacturer's warranty will apply.

o Repair and transportation costs of merchandise determined not to be defective.

o Cost associated with assembly, required oil, adjustments or other installation and start-up cost.

o ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM

ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

o IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

DeVilbiss Air Power Company

213 Industrial Drive • Jackson, TN 38301-9615 • Telephone: 1-800-888-2468 , Ext. 2 • FAX: 1-800-888-9036

Form: SP-100-E - 4/25/96

3

SAFETY GUIDELINES - DEFINITIONS

This manual contains information that is important for you to know and understand. This information relates to protecting YOUR

SAFETY and PREVENTING EQUIP-

MENT PROBLEMS. To help you recognize this information, we use symbols to the right. Please read the manual and pay attention to these sections.

URGENT SAFETY INFORMATION - A HAZARD

THAT WILL CAUSE SERIOUS INJURY OR LOSS

OF LIFE.

IMPORTANT SAFETY INFORMATION - A

HAZARD THAT MIGHT CAUSE SERIOUS

INJURY OR LOSS OF LIFE.

Information for preventing damage to equipment.

Information that you should pay special attention to.

IMPORTANT SAFETY INSTRUCTIONS

• SAVE THESE INSTRUCTIONS •

IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT

IN SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL

WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.

Risk of explosion.

HAZARD TO LOOK FOR

Compressed Gas

Excessive Operating Pressure

WHAT COULD HAPPEN

Oxygen will react with oil in tool causing an explosion. Flammable gases will ignite from sparking and cause the tool to explode.

THE TOOL COULD EXPLODE!

HOW TO PREVENT IT

Do not use any type of flammable gases or oxygen as a power source for the tool.

Use only filtered, lubricated, regulated compressed air .

Operate tool with clean, dry air regulated to 100 psi pressure maximum.

Unsuitable Cleaning Solvents Flammable vapors in the tool will ignite by a spark and could cause the tool to explode!

Never use gasoline or other flammable liquids to clean the tool.

Use non-flammable cleaning or degreasing materials.

4

SAFETY GUIDELINES

DANGER

Read these warnings carefully. Failure to follow warnings will result in severe injury or death!

Risk of head injury.

HAZARD TO LOOK FOR WHAT COULD HAPPEN HOW TO PREVENT IT

I njury to eyes, head and hearing Metal fragments, fasteners, or other material could be projected against head or into eyes. Continued exposure to an operating tool can result in permanent hearing damage.

Always wear ANSI approved Z87 safety glasses, Z89.1 head protection and

S3.19 hearing protection.

Risk of puncture injury.

HAZARD TO LOOK FOR WHAT COULD HAPPEN HOW TO PREVENT IT

Unsafe operation and improper handling of tool.

A fastener could accidentally be driven if the contact trip safety mechanism is not working.

Do not remove, modify or defeat contact safety device.

Damage to the tool or to the contact trip safety mechanism can result from improper handling, resulting in unsafe operation.

Do not use the tool if any shields or guards are removed or altered.

Always check contact trip safety mechanism of the tool before each use.

Death or a serious puncture would could occur if the contact trip bumps something or someone while holding the tool with the trigger depressed.

Never carry the tool by the hose or pull the hose to move the tool or a compressor. Keep hoses away from heat, oil and sharp edges. Replace any damaged, weak or worn hoses.

CONTINUED NEXT PAGE

5

SAFETY GUIDELINES

Risk of puncture injury.

HAZARD TO LOOK FOR WHAT COULD HAPPEN HOW TO PREVENT IT

Connecting and Disconnecting

Air Hose

Accidental discharge of a fastener can occur.

Hold tool by the handle and keep trigger and contact trip safety mechanism from contacting objects or parts of the body when connecting or disconnecting air supply.

Disconnect air hose before loading fasteners, removing a jammed fastener, servicing the tool, or moving the tool to another work area.

Do not use a check valve or any other fitting which allows air to remain in the tool.

Risk from flying objects.

HAZARD TO LOOK FOR WHAT COULD HAPPEN

Injury to self or others in the work area.

Fasteners could ricochet or be propelled causing injury to self or others.

When working along edges or next to voids in work surface, the contact trip safety mechanism could be depressed and allow the tool to discharge a fastener into the air or through thin work materials.

HOW TO PREVENT IT

Pay attention to others in the work area to assure that they are protected from possible accidental discharge of fastener, or projected fragments of work material, fasteners, etc.

Provide ANSI approved Z87 safety glasses, Z89.1 head protection, and S3.19

hearing protection to self and others in the work area.

Never point discharge of tool at self or others.

Do not pull trigger unless tool contact safety device is against work surface.

Never attempt to drive fasteners into hard surfaces such as steel, concrete, or tile.

Take care to avoid driving a fastener on top of another fastener.

Before operating tool, be certain that work surfaces are strong enough and thick enough to contain entire fastener.

Position tool carefully so that fasteners will be delivered to the proper location.

6

LUBRICATION AND MAINTENANCE

Do not store the tool in cold weather. Frost or ice can form on the operating valves or mechanisms and the tool may not operate correctly.

NOTE

Many air tool users find it convenient to use an Oiler to help provide oil circulation through tool. An Oiler also increases the efficiency and useful life of the tool. An oiler is recommended for tools that receive heavy or constant use. Check oil level in the oiler daily.

(See Figure 2)

Many air tool users find it convenient to use a Filter to remove liquid and solid impurities which can rust or

"gum up" internal parts of the tool. A Filter also increases the efficiency and useful life of the tool. Drain water from the filter periodically. (See Figure 3)

Figure 1

In cold weather operation (near or below freezing), DO

NOT USE a permanent antifreeze such as ethylene glycol for a cold weather lubricant. This type of anitfreeze will damage o-rings and seals of the tool.

NOTE

Proper lubrication is the owner's responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void your warranty.

Figure 2

Regulator

Your tool requires lubrication before you use it for the

first time and before and after each additional use. If an Oiler is used, manual lubrication through the air inlet is not required on a daily basis. Lubrication prevents wear and prevents rust from forming.

1. Disconnect the air supply from the tool before manually lubricating.

2. Turn the tool so the air inlet is facing up and put one

drop of Air Tool Oil, high speed spindle oil, such as

Unocal RX22, or 3-in-1 oil into the air inlet. DO NOT

USE detergent oil or additives. Operate the tool briefly after adding oil. (See Figure 1)

DO NOT OVER LUBRICATE AIR TOOL.

3. Wipe off excessive oil at the exhaust.

Figure 3

Oiler

Regulator

Filter

NOTE

Excessive oil will damage o-rings and seal of tool. If in-line oiler is used, manual lubrication through the air inlet is not required on a daily basis.

7

LUBRICATION AND MAINTENANCE

Do not use any type of flammable gases or oxygen as a power source for the tool. Use filtered, lubricated, regulated compressed air only. Use of compressed gas instead of compressed air may cause the tool to explode and cause death or serious personal injury.

Always connect the Female Quick Coupler to the air hose.

Never connect the Female Quick Coupler to the tool.

Do not use a check valve or any other fittings which will allow air to remain in the tool. Serious personal injury could occur.

Use a Pressure Regulator on your compressor with an operating pressure of 0-125 PSI. A Pressure Regulator is required to control the operating pressure of your tool.

Never carry the tool by the hose or pull the hose to move the tool or a compressor. Keep hoses away from heat, oil, and sharp edges. Replace any damaged, weak or worn hoses.

The air compressor must be able to maintain a minimum of

65 PSI when the tool is being used. An inadequate air supply can cause a loss of power or inconsistent operation.

NOTE

For better performance, install a 3/8" Quick Connector

(1/4" NPT threads) with an inside diameter of .315 (8 mm) on your Tool and a 3/8" Quick Coupler on the air

hose. A minimum of 3/8" I.D. air hose with a rated working pressure of 150 PSI or above should be used.

RECOMMENDED HOOK-UP

The following illustration shows the proper hook-up which will help prolong the life of the Tool.

NAILER

MALE

QUICK

CONNECTOR

(Supplied with Tool)

FEMALE

QUICK

COUPLER

MALE

QUICK

CONNECTOR

OILER FILTER

AIR

COMPRESSOR

AIR

HOSE

(3/8" I.D.)

FEMALE

QUICK

COUPLER

REGULATOR

8

CONTACT TRIP SAFETY MECHANISM

3.

The trigger is released after each fastener is driven.

4.

Move the tool to the next desired fastener location and repeat the procedure above.

CHECKING THE OPERATION OF

CONTACT TRIP SAFETY MECHANISM

Never keep the trigger pulled on contact trip tools when carrying or holding the tool. Death or a serious puncture wound could occur if the contact trip bumps something or someone.

Keep your hands and body away from the fastener discharge area of the tool. Serious personal injury could occur.

Check the operation of the contact trip safety mechanism often. Do not use the tool if the contact trip safety mechanism is not working correctly.

1. Disconnect the air supply from the tool.

2. Remove all fasteners from the magazine.

3. Make sure the trigger and contact trip safety mechanism move up and down without any sticking or binding.

Do not hold the tool against the work surface with extra force. Allow the tool to drive the fastener.

Do not use the contact trip mechanism as a means of discharging a fastener because:

1. It could result in personal injury

2. It could result in an accidental release of a fastener.

3. It may cause damage to the mechanism.

4. It could result in improper placement of fastener in work piece.

CONTACT TRIP

Your SHBN4 Slight-Headed Brad Nailer is a contact trip operated tool. When the operator depresses the contact trip safety mechanism against the work surface and then pulls the trigger, a fastener will be driven.

OPERATING A CONTACT TRIP TOOL:

1.

Requires finger to be off the trigger and the nose of the tool to be placed on the work surface.

2.

The contact trip safety mechanism is then depressed against the work surface and the trigger is pulled to drive a fastener.

9

Make sure not to pull the trigger or depress the contact trip safety mechanism when connecting the tool to an air compressor. Serious personal injury can occur if the tool cycles.

4. Reconnect air supply to the tool.

5. Depress the contact trip safety mechanism against the work surface without pulling the trigger. The tool must not cycle. Do not use the tool if a cycle occurs.

6. Hold the tool clear of the work surface. The contact trip safety mechanism should return to its original down position. Pull the trigger. The tool must not cycle. Do not use the tool if a cycle occurs.

7. Depress the contact trip safety mechanism against the work surface. Pull the trigger. The tool must cycle.

LOADING THE TOOL

Disconnect tool from air supply before adjusting, clearing jams, servicing, relocating and during non-operation.

Never place your hand, or any part of your body, in the fastener discharge area of the tool when air supply is connected to the tool. Serious personal injury may occur.

NOTE

Use DeVilbiss Air Power fasteners or equivalent for proper performance of tool. See page 15 for fastener information.

Handle the tool carefully. Respect the tool as a working implement and always assume the tool contains fasteners and is ready to operate.

a. Never use the tool as a toy and engage in horseplay.

b. Never aim or point the tool at anyone. The tool may contain fasteners.

c. Always keep people and animals at a safe distance from the work area in case of accidental discharge of fasteners.

d. Never pull the trigger unless the nose of the tool is against the work surface.

e. Do not pull the trigger or depress the contact trip when loading the Tool.

1. Disconnect air hose.

2. Pull up on the Stopper #56. Pull back on Reel Plate #50 to open magazine. (Items 50 & 56 - Page 13)

3. Insert a stick of fasteners into the magazine. Make sure the pointed ends of the fasteners are resting on the bottom edge of the magazine. Also make sure fasteners are not dirty or damaged. Use DeVilbiss fasteners or equivalent for proper fastener performance.

4. Push the magazine cover forward until the reel plate catches under stopper.

OPERATING THE TOOL

READ THIS MANUAL AND UNDERSTAND ALL

SAFETY WARNINGS AND INSTRUCTIONS BE-

FORE OPERATING TOOL.

Disconnect tool from air supply before adjusting, clearing jams, servicing, loading, relocating and during non-operation.

NOTE

Check and replace any damaged or worn components on the tool. The safety warning labels on the tool must also be replaced if they are not legible.

Protect your eyes and ears. Wear Z87 safety glasses with side shields. Wear hearing protection.

Employers and users are responsible for ensuring the user or anyone near the tool wear this safety protection.

10

OPERATING THE TOOL

1. Add one drop of DeVilbiss DV1719-01 Air Tool Oil, high speed spindle oil such as Unocal RX22, or 3-in1 oil into the air inlet.

2. Attach a Quick Connect Fitting to the tool.

3. Connect the Tool to an air compressor using a 3/8" I.D.

hose. (The magazine must be empty of all fasten-

ers). Make sure the hose has a rated working pressure exceeding 150 PSI and a Female Quick Coupler.

4. Regulate the air pressure to obtain 65 PSI at the tool.

Check the operation of the Contact trip safety mechanism following the instructions in this manual.

5. Load fasteners into your tool following the instruction in this manual.

6. Reconnect the air hose to the tool.

7. Test for proper fastener penetration by driving fasteners into a sample piece of material. If the fasteners do not achieve the desired penetration, adjust the air pressure to a lower or higher setting until the desired penetration is achieved. Do not exceed 100 psi at the tool.

CLEARING A JAM FROM THE TOOL

Disconnect tool from air supply before adjusting, clearing jams, servicing, relocating and during non-operation.

FASTENER JAM INSIDE MAGAZINE:

1. Disconnect tool from air hose.

2. Pull up on #56 Stopper. Pull back on #50 Reel Plate to open magazine. (Items #50 and #56 on page 13)

3. Remove jammed fastener from magazine.

4. Push Reel Plate forward until catch under stopper.

FASTENER JAMMED IN FASTENER DISCHARGE AREA:

1.

Disconnect tool from air hose.

2.

Pull up on Stopper #56. Pull back on Reel Plate #50 to open magazine. (Items #50 and #56 on page 13)

3.

Pull up on Stopper #56. Pull back on Reel Plate #50 to open magazine.

4.

Remove fasteners in magazine.

5.

Remove 2 screws from nose door.

6.

Remove nose door.

7.

Grab jammed fastener with pilers and remove.

(See Figure 5)

8.

Reposition nose door and secure with 2 screws.

9.

Reload fasteners.

10. Push Reel Plate forward until catches under stopper.

11

Figure 5

TROUBLESHOOTING GUIDE

Stop using the tool immediately if any of the following occur. Serious personal injury could occur.

Warranty repairs or replacements must be performed by a DeVilbiss Air Power Authorized

Service Center Only.

PROBLEM

Air leaking at trigger valve area.

Air leaking between housing and exhaust deflector.

Tool fails to drive fastener.

Tool runs slow or has loss of power.

Fasteners are jammed in tool.

CAUSE SOLUTION

Seals in trigger valve housing are damaged.

Seals must be replaced & operation of

Contact trip must be checked. (NSK-019)

Loosen exhaust deflector screws.

Damaged cylinder cap seals.

Damaged firing valve seals.

Cap spring weak or damaged.

Screws need to be tightened.

Replace cap seals. (NSK-005)

Seals must be replaced. (NSK-005)

Spring needs replaced. (NSK-005)

Worn joint guide.

Driver blade damaged.

Dirt between guide body and door.

Dirt or damage prevents fasteners or fastener pusher from moving freely in magazine.

Damaged fastener pusher spring.

Inadequate air flow or pressure to Tool.

Worn seal on piston or lack of lubrication.

Damaged seal on trigger assembly.

Air leaks.

Cylinder sleeve seals damaged.

Cap seal leaking.

Joint guide needs to be replaced.

(NSK-007)

Replace driver blade. (NSK-001)

Clean.

Magazine needs to be cleaned.

Spring needs to be replaced.

Verify pressure/flow to tool.

Seal need to be replaced. Lubricate.

(NSK-001)

Seal need to be replaced. (NSK-019)

Screws and fittings need to be tightened.

Replace seals. (NSK-007)

Seal needs to be replaced. (NSK-005)

Tool not lubricated sufficiently.

Inadequate air flow or pressure to tool.

Broken spring in cylinder cap.

Worn seal on piston or lack of lubrication.

Exhaust port in cap is blocked.

Tools needs to be lubricated.

Vertify air flow or pressure to tool.

Spring needs to be replaced. (NSK-005)

Replace seal. Lubricate (NSK-001)

Inspect and clear blockage.

Driver blade is worn or damaged.

Fasteners coming apart in magazine.

Fasteners are not correct size.

Magazine latch assembly weak/damaged.

Fasteners are bent.

Guide body groove damaged.

Door groove damaged.

Fastener pusher system defective.

Replace driver blade. (NSK-001)

Verfiy and replace.

Fasteners recommended for Tool must be used.

Replace Stopper.

Replace with undamaged fasteners

Replace guide body.

Replace door.

Determine defective part and replace.

12

EXPLODED VIEW

13

PARTS LIST

KEY

NO.

+

# 1 8

4

19

20

4

21

# 2 2

4

23

24

25

4

26

4

27

28

4

29

30

3

* 4

1

2

* 5

6

* 7

* 8

9

* 10

* 11

12

+ 1 3

+ 1 4

+ 1 5

# 1 6

17

PART

NUMBER DESCRIPTION

NSP-154

NSP-182

NSP-074

-----

-----

NSP-077

-----

-----

NSP-079

-----

-----

NSP-082

-----

-----

-----

-----

NSP-085

-----

-----

NSP-088

-----

-----

-----

-----

NSP-072

NSP-124

NSP-147

NSP-071

NSP-092

NSP-146

Screw

Washer

Exhaust Deflector

Spring

Seal

Cylinder Cap Assy.

Seal

Seal

Firing Valve Assy.

Seal

Seal

Collar

Seal

Main Piston

Driver (Regular)

Seal

Cylinder Sleeve Assy.

Piston Stop

Seal

Tube

Seal

Joint Guide

Seal

-----

Trigger Valve Assy.

Seal

Seal

Trigger Valve Guide

Spring

Retainer

KEY

NO.

48

49

50

51

52

43

44

45

46

47

38

39

40

41

42

31

32

33

34

35

36

37

53

54

55

56

57

58

59

60

PART

NUMBER DESCRIPTION

NSP-163

NSP-093

NSP-095

NSP-096

NSP-070

NSP-094

NSP-097

NSP-069

NSP-098

NSP-099

NSP-100

NSP-103

NSP-135

NSP-105

NSP-104

NSP-106

NSP-107

NSP-101

NSP-184

NSP-108

NSP-109

NSP-110

NSP-102

NSP-111

NSP-112

NSP-113

NSP-114

NSP-115

NSP-116

NSP-176

Pin

Inner Trigger

Trigger

Pin

Shaft

Spring

Main Body Assy.

Safety

Guide Body

Plate

Door

Screw

Screw

Magazine Unit A

Flat Bar

Magazine Unit B

Stopper

Stopper

Washer

Reel Plate

Pusher

Pusher

Spring

Screw

Bracket

Stopper

Stopper

Nut

Screw

Air Plug

PART KITS

* Key Numbers 4, 5, 7, 8, 10, and 11 can only be purchased as part of NSK-005 Top Repair Kit.

+ Key Numbers 13, 14, 15, and 22 can only be purchased as part of NSK-001 Driver Blade Kit.

# Key Numbers 16, 18, and 22 can only be purchased as part of NSK-007 Bottom Repair Kit.

4 Key Numbers 19, 21, 23, 26, 27, and 29 can only be purchased as part of NSK-019 Trigger Repair Kit.

14

FASTENERS

Fastener

Part #

4F16

4F20

4F25

4F30

4F32

Length

5/8"

3/4"

1"

1 3/16""

1 1/4"

Shank

Gauge

18 GA

18 GA

18 GA

18 GA

18 GA

Shank

Type

-

-

-

-

-

Crown or

Head Type

Brad/Brown

Brad/Brown

Brad/Brown

Brad/Brown

Brad/Brown

Collation

Adhesive

Adhesive

Adhesive

Adhesive

Adhesive

Finish

Galvanized

Galvanized

Galvanized

Galvanized

Galvanized

QTY

Per

Box

5,000

5,000

5,000

5,000

5,000

INTERCHANGE INFORMATION

The DeVilbiss Slight-Headed Brad Nailer SHBN4, will accept Fasteners for:

Bostitch

Senco

Duofast

Paslode

Fasco

Atro

Bea

Haubold

T29-30, T31-1

LS2, LS3, LS4, LS5

BB4440

2138-F18

F22, F25

125

SI25

PNI6K

These Fasteners should be the same length and shank gauge as the DeVilbiss Fasteners.

15

STEEL DRIVERS SERIES

Operating, Maintenance and Parts

Manual for SHBN4

Slight-Headed Brad Nailer

Retain the original sales receipts as proof of purchase for warranty repair work.

Attach sales receipt here.

Call our Toll Free Number 1-800-888-2468, Ext 2, then 1, to obtain the location of the nearest Authorized Service Center for ordering repair parts and for warranty repairs.

When ordering repair parts from your local Authorized Service Center, always give the following information:

• Model number of your product

• Part number and description of the item you wish to purchase

WARRANTY

This product is covered by the DeVilbiss one year limited warranty. The warranty can be found on page 3 or is available upon request.

DeVilbiss Air Power Company • 213 Industrial Drive • Jackson, TN 38301-9615