The A23 battery has a shelf life of about 1 year. The product fully complies
with Part 15 of the FCC Regulations.
1B - Technical Specifications
Operating frequency
Number of buttons
Battery:
Number combinations:
Operating temperature:
Overall dimensions:
Weight:
1C - Main components
300 MHz
2
1 ea. 12V A23
1024
-20°F — 100°F
1/2" x 3" x 1-5/8"
1 oz.
Front View
LED
Push
Push button 2
button 1
Sliding
battery/
dip switch Grey Case
access
Back View
Clip Screw
slot
Manual - 300 2 Button
Transmitter
Solutions
©
STINGER"
TRANSMITTER
Thank you for choosing a Transmitter Solutions product.
Please read this manual carefully before using the product.
Made in China. Copyright © 2006 by Transmitter Solutions.
CONTENTS
1 - TRANSMITTER OVERVIEW
1A - General information
1B - Technical specifications
1C - Main components
2 - CODING
3 - OPERATION
4 - BATTERY ACCESS
5 - TROUBLESHOOTING
1A - General information
The Trnasmitter Solutions - Stinger™ Transmitter is a very small (1-5/8" x
3" x 1/2") visor style wireless transmitter operating at 300 MHz. The
Stinger™ achieves its small size by using state-of-the-art, surface mount
components. It has been designed for use with and is compatible with dll dip
switch receivers operating at a 300 frequency, including all Multicode® dip
switch digital receivers.
Multicode is a registered trademark owned by Linear Corporation.
2 - CODING
Set the ten-digit toggle codes on both sets of switches to match the codes set
from another functioning transmitter. Access to the Stinger™s toggle code (DIP)
switches is achieved by sliding off bottom front cover, removing battery (if
necessary), and removing top cover by loosening screw on back. Move
switches using a small pointed object, such as a paper clip, gently switching the
small switches to either the ON or OFF position. (In Detail below, switches 3, 5,
6, 8 and 10 are in the ON position.) When complete, reinstall battery, reattach
top cover, tighten screw, slide bottom front cover back into original position.
Front
3- OPERATION Top
Once the codes are set to match the transmitter codes, ida
you may test the system. Ensure the gate or door is ~~ View
visible and clear before testing.
TM,
Step 1. Push the Stinger""s button from a distance of switch i
about fen feet. If the receiver activates, the switches Switch
are properly matched. 2
Step 2. Test the transmitter from several locations to
discover any "blind spots" caused by interference.
4 - BATTERY ACCESS
Slide front cover down to reach battery compartment.
Attend to proper polarity when installing or
replacing battery. See "coding" for proper
removal and replacement of cover.
5 - TROUBLESHOOTING
POLA 7
The system does not receive
the transmitter signal.
The transmitter LED will not light.
Bottom
Cover
NOTE:
Switch 1 = Button 1
y Swtich 2 = Button 2
Switches
SOLUTION
Ensure clear plastic battery
insulator has been removed; OR
Replace the transmitter battery.
Check to ensure the
transmitter switches are coded to
match your system receiver.
The system does not receive
the transmitter signal.
The transmitter LED is ON.
Replace the
Th ti i . .
e operating range is reduced transmitter battery.
Transmitter Solutions Stinger" Type: 300MCD22V
FCC ID : SU7CCS3001BV
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept interference received, including
interference that may cause undesired operation.
Notice
Any changes or modifications to Transmitter Solutions equipment not
expressly approved by Transmitter Solutions could void the manufacturer's
warranty and could void the user's authority to operate the equipment.
WARRANTY
The warranty period of Transmitter Solutions Stinger™ transmitters is 24
months, beginning from the manufacturing date of the transmitter. During
this period, if the product does not operate correctly, due to a defective
component, the product will be repaired or replaced at the sole discretion of
Transmitter Solutions. The warranty does not extend to the transmitter case
which can be damaged by conditions outside the control of Transmitter
Solutions, or to battery life.
ZN
Transmitter
SOLUTION S®
7380 S. Eastern Avenue, Suite 124-320 * Las Vegas, NV 89123
(866) 975-0101 * (866) 975-0404 Fax
www.transmittersolutions.com
">
