Manitou Series 2-E2 MT1033 HL Turbo Rough Terrain Forklift Operator's Manual
PDF
Έγγραφο
Διαφήμιση
Διαφήμιση
INTRODUCTION TO SAFETY CONTENTS MANITOU NORTH AMERICA, INC. 6401 IMPERIAL DRIVE WACO, TX 76712-6803 For Parts Orders contact your Manitou North America Dealer or call: Manitou North America, Inc. Parts Dept. (800) 425-3727 or (254) 799-0232 Parts Dept. Fax (254) 867-6504 Website: www.manitou-na.com MT1033 HL Turbo Series 2-E2 S/N: 206177 & above OPERATOR'S MANUAL THIS OPERATOR'S MANUAL MUST BE KEPT IN THE LIFT TRUCK AND MUST BE READ AND UNDERSTOOD BY THE LIFT TRUCK OPERATOR. 547857AS R11-10 INTRODUCTION TO SAFETY CONTENTS INTRODUCTION TO SAFETY CONTENTS - INTRODUCTION TO SAFETY - - ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS - - - I - SAFTETY MESSAGES - - - - - - - - - - - - - - - - - - - - - - - - - - VII - SAFETY DECALS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - VIII - TABLE OF CONTENTS - - - - - - - - - - - - - - - - - - - - - - - - - - XV R03-04 INTRODUCTION TO SAFETY CONTENTS INTRODUCTION TO SAFETY CONTENTS ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS I INTRODUCTION TO SAFETY CONTENTS ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS STUDY THE OPERATOR/SERVICE MANUALS The information in this manual provides general instructions for the safe operation and maintenance of your forklift truck. This information is vital and must be clearly understood by the operator and serviceman. Study this manual and the Rough Terrain Forklift Safety Manual (part no. 422494) thoroughly and carefully before operating or servicing your forklift. Contact your dealer or Manitou North America, Inc. if you have any questions concerning your forklift, its operation, service or parts. Keep both manuals in the literature box on the forklift available for reference. If either manual becomes illegible or is missing, contact your dealer for replacements immediately. This manual cannot cover every situation that might result in an accident. It is the responsibility of the operator to always remain alert for potential hazards and be prepared to avoid them! ADDITIONAL RECOMMENDED LITERATURE: ANSI / ITSDF B56.6 is the national consensus standard for rough terrain forklift trucks. It contains rules about forklift safety, maintenance, safe operation, training, and supervision. Forklift owners should learn this standard and make it available for their operators, service personnel, and supervisors. These standards can be obtained, free of charge, from the Industrial Truck Standards Development Foundation (ITSDF) on their website at www.itsdf.org. The following references are examples from the standard, addressing forklift operators: A.) OPERATOR TRAINING QUALIFICATIONS 1.) The user shall ensure that operators understand that safe operation is the operator’s responsibility. The user shall ensure that operators are knowledgeable of, and observe, all safety rules and practices. 2.) Create an effective operator training program centered around user company’s policies, operating conditions, and rough terrain forklift trucks. The program should be presented completely to all new operators and not be condensed for those claiming previous experience. 3.) Information on operator training is available from several sources, including rough terrain forklift truck manufacturers, users, government agencies, etc. 4.) An operator training program should consist of the following: a.) careful selection of the operator, considering physical qualifications, job attitude, and aptitude; b.) emphasis on safety of stock, equipment, operator, and other personnel; c.) citing of rules and why they were formulated; d.) basic fundamentals of rough terrain forklift truck and component design as related to safety, e.g., in.-lb (N-m) loading, mechanical limitations, center of gravity, stability, etc.; e.) introduction to equipment, control locations, and functions. Explain how they work when used properly and problems when used improperly. f.) supervise practice on operating course remote from normal activity and designed to simulate actual operations, e.g., lumber stacking, elevating shingles to the roof, etc.; g.) oral, written, and operational performance tests and evaluations during and at completion of the course; h.) refresher courses, which may be condensed versions of the primary course, and periodic “on job” operator evaluation; i.) understanding of nameplate data and operator instructions and warning information appearing on the rough terrain forklift truck. B.) GENERAL SAFETY PRACTICES 1.) Rough terrain forklift trucks can cause injury if improperly used or maintained. 2.) Only authorized operators trained to adhere strictly to all operating instructions shall be permitted to operate rough terrain forklift trucks. Unusual operating conditions may require additional safety precautions, training, and special operating instructions. 3.) Modifications and additions which affect capacity or safe operation shall not be preformed without the manufacturer’s prior written approval. Where such authorization is granted, capacity, operation, and maintenance instruction plates, tags, or decals shall be changed accordingly. 4.) If the rough terrain forklift truck is equipped with front end attachment(s) or optional forks, the user shall see that the truck is marked to identify the forks or attachment(s), show the approximate weight of the truck and fork or attachment combination, and show the capacity of the truck with forks or attachment(s) at maximum elevation with load laterally centered. 5.) The user shall see that all nameplates and caution and instruction markings are in place and legible. 6.) The user shall consider that changes in load dimension may affect rough terrain forklift truck capacity. II INTRODUCTION TO SAFETY CONTENTS ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.) B.) GENERAL SAFETY PRACTICES (cont.) 7.) Where steering can be accomplished with either hand and the steering mechanism is of a type that prevents road reactions from causing the handwheel to spin (power steering or equivalent), steering knobs may be used. When used, steering knobs shall be of a type that can be engaged by the operator’s hand from the top and shall be within the periphery of the steering handwheel. 8.) Experience has shown that rough terrain forklift trucks which comply with stability requirements are stable when properly operated. However, improper operation, faulty maintenance, or poor housekeeping may contribute to a condition of instability and defeat the purpose of the requirements. 9.) Users shall give consideration to special operating conditions. The amount of forward and rearward tilt to be used is governed by the application. Although the use of maximum rearward tilt is allowable under certain conditions, such as traveling with the load lowered, the stability of a rough terrain forklift truck as determined by standardized tests does not encompass consideration for excessive tilt at high elevations or the operation of trucks with excessive off-center loads. 10.) Some of the conditions which may affect stability are ground and floor conditions, grade, speed, loading (rough terrain forklift trucks equipped with attachments behave as partially loaded trucks even when operated without a load on the attachment), dynamic and static forces, improper tire inflation, and the judgement exercised by the operator. C.) OPERATING SAFETY RULES AND PRACTICES 1.) Safe operation is the responsibility of the operator. 2.) This equipment can be dangerous if not used properly. The operator shall develop safe working habits and also be aware of hazardous conditions in order to protect himself, other personnel, the rough terrain forklift truck, and other material. 3.) The operator shall be familiar with the operation and function of all controls and instruments before undertaking to operate the rough terrain forklift truck. 4.) Before operating any rough terrain forklift truck, truck operators shall have read and be familiar with the operator’s manual for the particular truck being operated. 5.) Before starting to operate the rough terrain forklift truck: a.) be in operating position and fasten seat belt; b.) place directional controls in neutral; c.) apply brakes; d.) start engine. 6.) Do not start or operate the rough terrain forklift truck, any of its functions, or attachments from any place other than the designated operator’s position. 7.) Keep hands and feet inside the operator’s designated area or compartment. Do not put any part of the body outside the operator compartment of the rough terrain forklift truck. 8.) Never put any part of the body into the mast structure or between the mast and the rough terrain forklift truck. 9.) Never put any part of the body within the reach mechanism of the rough terrain forklift truck or other attachments. 10.) Understand rough terrain forklift limitations and operate the truck in a safe manner so as not to cause injury to personnel. 11.) Do not allow anyone to stand or pass under the elevated portion of any rough terrain forklift truck, whether empty or loaded. 12.) Do not permit passengers to ride on rough terrain forklift trucks. 13.) Check clearance carefully before driving under electrical lines, bridges, etc. 14.) A rough terrain forklift truck is attended when the operator is less than 25 ft (7.6m) from the truck, which remains in his view. 15.) A rough terrain forklift truck is unattended when the operator is 25ft (7.6m) or more from the truck, which remains in his view, or whenever the operator leaves the truck and it is not in his view. 16.) Before leaving the operator’s position: a.) bring rough terrain forklift truck to a complete stop; b.) place directional controls in neutral; c.) apply the parking brake; d.) lower load-engaging means fully, unless supporting an occupied elevated platform; e.) stop the engine; f.) if the rough terrain forklift truck must be left on an incline, block the wheels; g.) fully lower the load-engaging means. 17.) Maintain a safe distance from the edge of ramps, platforms, and other similar working surfaces. 18.) Do no move railroad cars or trailer with a rough terrain forklift truck. III INTRODUCTION TO SAFETY CONTENTS ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.) C.) OPERATING SAFETY RULES AND PRACTICES (cont.) 19.) Do not use a rough terrain forklift truck for opening or closing railroad car doors. 20.) In areas classified as hazardous, use only rough terrain forklift trucks approved for use in those areas. 21.) Report all accidents involving personnel, building structures, and equipment to the supervisor or as directed. 22.) Do not add to, or modify, the rough terrain forklift truck. 23.) Do not block access to fire aisles, stairways, and fire equipment. 24.) For rough terrain forklift trucks equipped with a differential lock, the lock should not be engaged when driving on the road or at high speeds or when turning. If the lock is engaged when turning, there could be loss of steering control. 25.) Observe all traffic regulations including authorized speed limits. Under normal traffic conditions, keep to the right, maintain a safe distance, based on speed of travel, from the truck ahead; and keep the truck under control at all times. 26.) Yield the right-of-way to pedestrians and emergency vehicles such as ambulances and fire trucks. 27.) Do not pass another truck traveling in the same direction at intersections, blind spots, or at other dangerous locations. 28.) Slow down and sound the audible warning device(s) at cross-aisles and other locations where vision is obstructed. 29.) Cross railroad tracks at an angle wherever possible. Do not park closer than 6 ft (1.8m) to the nearest rail of a railroad track. 30.) Keep a clear view of the path of travel and observe other traffic, personnel, and safe clearances. 31.) If the load being carried obstructs forward view, travel with the load trailing. 32.) Ascend or descend grades slowly and with caution. a.) When ascending or descending grades in excess of 5%, loaded rough terrain forklift trucks should be driven with the load upgrade. b.) Unloaded rough terrain forklift trucks should be operated on all grades with the load-engaging means downgrade. c.) On all grades, the load and load-engaging means shall be tilted back, if applicable, and raised only as far as necessary to clear the road surface. d.) Avoid turning, if possible, and use extreme caution on grades, ramps, or inclines; normally travel straight up or down. 33.) Under all travel conditions, operate the rough terrain forklift truck at a speed that will permit it to be brought to a stop in a safe manner. 34.) Travel with load-engaging means or load low and, where possible, tilted back. Do not elevate the load except during stacking. 35.) Make starts, stops, turns, or direction reversals in a smooth manner so as not to shift load and/or overturn the rough terrain forklift truck. 36.) Do not indulge in stunt driving or horseplay. 37.) Slow down for wet and slippery surfaces. 38.) Before driving over a dockboard or bridge plate, be sure that it is properly secured. Drive carefully and slowly across the dockboard or bridge plate, and never exceed its rated capacity. 39.) Do not drive rough terrain forklift trucks onto any elevator unless specifically authorized to do so. Approach elevators slowly, and then enter squarely after the elevator car is properly leveled. Once on the elevator, neutralize the controls, shut off engine, and set brakes. It is advisable that all other personnel leave the elevator before truck is allowed to enter or leave. 40.) Avoid running over loose objects on the roadway surface. 41.) When negotiating turns, reduce speed to a safe level, and turn steering handwheel in a smooth sweeping motion. Except when maneuvering at a very low speed, turn the steering handwheel at a moderate, even rate. 42.) Use special care when traveling without load, as the risk of lateral overturning is greater. 43.) Improper use of stabilizer controls (if so equipped) could cause rough terrain forklift truck upset. Always lower the carriage before operating stabilizer controls. 44.) For rough terrain forklift trucks equipped with lateral leveling: a.) Always level the frame before raising the boom or mast, with or without a load. b.) Lateral leveling should not be used to position an elevated load; instead, lower the load and reposition the rough terrain forklift truck. 45.) Handle only stable or safely arranged loads. a.) When handling off-center loads which cannot be centered, operate with extra caution. b.) Handle only loads within the capacity of the rough terrain forklift truck. c.) Handle loads exceeding the dimensions used to establish rough terrain forklift truck capacity with extra caution. Stability and maneuverability may be adversely affected. IV INTRODUCTION TO SAFETY CONTENTS ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.) C.) OPERATING SAFETY RULES AND PRACTICES (cont.) 46.) When attachments are used, extra care shall be taken in securing, manipulating, positioning, and transporting the load. Operate rough terrain forklift trucks equipped with attachments as partially loaded trucks when not handling a load. 47.) Completely engage the load with the load-engaging means. Fork length should be at least two-thirds of load length. Where tilt is provided, carefully tilt the load backward to stabilize the load. Caution should be used in tilting backward with high or segmented loads. 48.) Use extreme care when tilting load forward or backward, particularly when high tiering. Do not tilt forward with load-engaging means elevated except to pick up or deposit a load over a rack or stack. When stacking or tiering, use only enough backward tilt to stabilize the load. 49.) The handling of suspended loads by means of a crane arm (boom) or other device can introduce dynamic forces affecting the stability of a rough terrain forklift truck. Grades and sudden starts, stops, and turns can cause the load to swing and create a hazard if not externally stabilized. When handling suspended loads: a.) do not exceed the truck manufacturer’s capacity of the rough terrain forklift truck as equipped for handling suspended loads. b.) only lift the load vertically and never drag it horizontally; c.) transport the load with the bottom of the load and the mast as low as possible; d.) with load elevated, maneuver the rough terrain forklift truck slowly and cautiously, and only to the extent necessary to permit lowering to the transport position; e.) use tag lines to restrain load swing whenever possible. 50.) At the beginning of each shift and before operating the rough terrain forklift truck, check its condition, giving special attention to: a.) tires and their inflation pressure b.) warning devices c.) lights d.) lift and tilt systems, load-engaging means, chains, cables, and limit switches e.) brakes f.) steering mechanism g.) fuel system(s) 51.) If the rough terrain forklift truck is found to be in need of repair or in any way unsafe, or if it contributes to an unsafe condition, the matter shall be reported immediately to the user’s designated authority, and the truck shall not be operated until it has been restored to safe operating condition. 52.) If during operation the rough terrain forklift truck becomes unsafe in any way, the matter shall be reported immediately to the user’s designated authority, and the truck shall not be operated until it has been restored to safe operating condition. 53.) Do not make repairs or adjustments unless specifically authorized to do so. 54.) When refueling, smoking in the area shall not be permitted, the engine shall be stopped, and the operator shall not be on the rough terrain forklift truck. 55.) Spillage of oil or fuel shall be carefully and completely absorbed or evaporated and fuel tank cap replaced before restarting engine. 56.) Do not use open flames when checking electrolyte level in storage batteries, liquid level in fuel tanks, or the condition of LPG fuel lines and connectors. 57.) Do not lift personnel with the forklift. If the forklift must be used to lift people, precautions for the protection of the personnel must be taken (see ITSDF B56.6, chapter 5.15 Elevating Personnel). V ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.) D.) SUSPENDED LOADS A jib or truss boom should ONLY be used to lift and place loads when the machine is stationary and the frame is level. Transporting suspended loads must ALWAYS be done slowly and cautiously, with the boom and load as low as possible. Use taglines to restrict loads from swinging, to avoid overturn. The handling of suspended loads by means of a truss boom or other similar device can introduce dynamic forces affecting the stability of the machine that are not considered in the stability criteria of industry test standards. Grades and sudden starts, stops and turns can cause the load to swing and create a hazard. Guidelines for “Free Rigging / Suspended Loads” 1. DO NOT exceed the rated capacity of the telescopic handler as equipped for handling suspended loads. The weight of the rigging must be included as part of the load. 2. During transport, DO NOT raise the load more than 12 inches (305 mm) above the ground, or raise the boom more than 45 degrees. 3. Only lift the load vertically – NEVER drag it horizontally. 4. Use multiple pickup points on the load when possible. Use taglines to restrain the load from swinging and rotating. 5. Start, travel, turn and stop SLOWLY to prevent the load from swinging. DO NOT exceed walking speed. 6. Inspect rigging before use. Rigging must be in good condition and in the U.S. comply with OSHA regulation §1910.184, “Slings,” or §1926.251, “Rigging equipment for material handling.” 7. Rigging equipment attached to the forks must be secured such that it cannot move either sideways or fore and aft. The load center must not exceed 24 inches (610 mm). 8. DO NOT lift the load with anyone on the load, rigging or lift equipment, and NEVER lift the load over personnel. 9. Beware of the wind, which can cause suspended loads to swing, even with taglines. 10. DO NOT attempt to use frame-leveling to compensate for load swing. WARNING U.S. OSHA regulations effective November 8, 2010 (29 CFR Part 1926, Subpart CC - Cranes and Derricks in Construction) include requirements for employers that use powered industrial trucks ("forklifts") configured to hoist (by means of a winch or hook) and move suspended loads horizontally. In particular, this regulation applies to any rough-terrain forklift (e.g., "telescopic handler") equipped with a jib or truss boom with a hook (with or without a winch), or a hook assembly attached to the forks. [Note: This regulation is in addition to the OSHA regulation that requires specific forklift operator training: §1910.178(l).] When a forklift / telescopic handler is configured and used for hoisting, the employer must ensure that: 1. Forklift, lift equipment and rigging have been inspected (each shift, month and year) and are in good, safe condition and properly installed. 2. An operator's manual and applicable load charts are on the forklift. 3. Work zone ground conditions can support the equipment and load. Any hazardous conditions in the work area have been identified, and the operator notified. 4. Equipment is being used within its rated capacity and in accordance with the manufacturer's instructions. VI 5. Operator and crew members have been trained in the safe use and operation of the equipment, including how to avoid electrocution. 6. During use, no part of the equipment, load line or load will be within the minimum clearance distance specified by OSHA [10 feet (3.0 m), and more for lines rated over 50 kV] of any energized power line, and any taglines used are non-conductive. 7. In addition, for lift equipment with a rated capacity greater than 2000 lbs. (907 kg), the employer must ensure that: a.) An accessible fire extinguisher is on the forklift; b.) Monthly and annual inspections are performed and documented, and records retained (three months for monthly, one year for annual); c.) Before November 10, 2014, operators must have had the additional training and qualification / certification required by OSHA regulations §1926.1427 and §1926.1430. Note: Refer to the full text of the OSHA crane regulation (29 CFR Part 1926, Subpart CC) for a detailed description VII ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.) CONCLUSION: 1.) ATTEND OPERATOR TRAINING CLASSES The forklift operator must clearly understand all instructions concerning the safe operation of the forklift and all safety rules and regulations of the work site. They must have successfully completed a training coarse in accordance with the Powered Industrial Truck Standard (29 CFR 1910.178) as described by the Occupational Safety and Health Administration (OSHA). They must be qualified as to their visual, hearing, physical, and mental ability to operate the equipment safely. NEVER use drugs or alcohol while operating a forklift! NEVER operate or allow anyone to operate a forklift when mental alertness or coordination is impaired! An operator on prescription or over-the-counter drugs must consult a medical professional regarding any side effects of the medication that may impair their ability to safely operate the forklift. 2.) CREATE A MAINTENANCE PROGRAM OSHA recommends a maintenance log, listing repairs requested and completed, for each forklift. Also, “lock out tag procedures” should be utilized. If the forklift malfunctions; park it safely, remove the key, tag “Do Not Use”, and report the problem to the proper authority or authorized service personnel immediately. ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.) 2.) CREATE A MAINTENANCE PROGRAM (cont.) For the best forklift performance and operation, a maintenance program is required. Use the hour meter on the instrument panel to keep maintenance properly scheduled (see SECTION TWO - “Servicing Schedule”). For repairs on major components (engine, transmission, etc.), contact your nearest dealer for a Repair Manual. Do not operate a forklift that is damaged or does not function properly. Only authorized personnel may make repairs or adjustments to the lift truck. After repairs, the lift truck must be tested for safe operation before returning to service. 3.) FORKLIFT KNOWLEDGE Forklift trucks can cause serious injury if improperly used or maintained. Study all of the manuals provided for your forklift model. Learn the locations and meanings of all safety decals. If any decals are illegible or missing, have them replaced immediately. Make sure all safety features provided by the original manufacturer are in place and function properly. Do not operate a forklift with damaged, missing or unsafe components. Have it repaired by authorized service personnel. Learn the functions of all controls, gauges, indicator lights, etc. on the forklift. Know the speed/gear ranges, braking and steering capabilities, load ratings and clearances. When referring to the location of forklift components, the terms “left”, “right”, “front”, and “rear” are related to the operator seated normally, facing forward in the operator’s seat. If you have any questions about the forklift, consult your supervisor. Failure to fully understand or obey safety warnings can result in serious injury or death! 4.) WORK SITE KNOWLEDGE Before operating on a work site, learn the rules for movement of people, forklifts and all other traffic. Check the size, weight, and condition of the loads you will be expected to handle. Verify that they are properly secured and safe to transport. Learn where the loads are to be placed, planning your route for a safe approach, watching for hazardous conditions. Will a signal man be required to help place the load? Remove any debris which may cause tire damage or rupture. Plan your route around problem areas or have them corrected. Inform the supervisor of any unsafe conditions observed at the site. Examples of hazards: power lines, cables, low clearance structures, garage doors, telephone pole guide lines, fencing, loose lumber, building materials, drop-offs, trenches, rough/soft spots, oil spills, deep mud, steep inclines, railroad tracks, curbs, etc.. NEVER approach power lines, gas lines or other utilities with the forklift! Always verify that local, state/provincial and federal regulations have been met. Report any accidents involving personnel, building structures, and equipment to the supervisor immediately. Always remain alert - conditions are constantly changing at the work site! TECHNICAL SUPPORT All data provided in this manual is subject to production changes, addition of new models, and improved product designs. If a question arises regarding your forklift, please consult your dealer or K-D Manitou, Inc. for the latest information. When ordering service parts or requesting technical information, be prepared to quote the applicable Model/Serial Numbers. VIII SAFETY MESSAGES NOTE THE SAFETY ALERT SYMBOL (SHOWN BELOW). IT IDENTIFIES POTENTIAL HAZARDS WHICH, IF NOT AVOIDED MAY RESULT IN INJURY OR DEATH! Also, observe the safety messages places throughout this manual; providing special instructions, telling you when to take precautions and to identify potential hazards. The safety messages are highlighted and outlined in a box similar to those shown in the examples below. SAFETY ALERT SYMBOL NOTE or NOTICE Provides information, special instructions or references about the lift truck. IMPORTANT Precautions which must be taken to avoid damage to the lift truck. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. May also alert unsafe practices. WARNING Indicates a potentially hazardous situation which, if not avoided, may result in death or serious injury! DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. CALIFORNIA PROPOSITION 65 WARNING Diesel Engine Exhaust and some of its constituents are known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING: Battery posts, terminals and related accesories and related accessories contain lead and lead compounds. Wash hands after handling. IX INTRODUCTION TO SAFETY CONTENTS SAFETY DECALS The purpose of this chapter is to introduce you to the safety messages, decals, and nameplates found on your forklift truck. The decals are identified by name, part number, location, and a brief description. (The forklift model logos, and other misc. decals not shown, can be found in your forklift parts manual.) The decals illustrated may not be exactly the same as those installed on your forklift; installation of the decals varies depending on the forklift model, series, decal updates, etc.. The size and location of some decals limit the amount of information that can be placed upon it. For this reason, additional detailed information not found on the decals is provided through-out this manual. Every decal placed on the lift truck is important; they are constant reminders of safety and instructions that should never be taken for granted. Even experienced operators can be seriously injured or killed by ignoring, refusing to enforce, or forgetting to follow safe operating procedures! Do not assume you know all safety issues concerning the decals. Before operating the lift truck; learn the meaning(s) of the decals as described in this manual. If any decal becomes illegible or missing, have it replaced immediately! Always replace decals using the same decal part no., unless otherwise specified by the manufacturer. For replacement decals not found in your parts manual, contact your nearest dealer. If you have any questions, contact your supervisor or nearest dealer for advice before operating your forklift! 801011 Before Starting - 801011 (Boom equipped models). Location: on the brake fluid cover panel (to the left and below the dash panel). Safety Instructions - 420792 (Mast equipped models). Location: on or near the operator manual storage case, and/or on the dash panel. Instructions for the forklift operator; before operating the forklift. Use of Seat Belt - 801012 (Boom equipped models). Location: to the right of the operator, near the hydraulic control lever. Instructs the operator to always wear the seat belt during operations, and never jump from an over-turning forklift. X INTRODUCTION TO SAFETY CONTENTS SAFETY DECALS Emergency and Parking Brake - 801010 Location: near the park brake lever. Identifies the Emergency/Parking Brake Lever. Alarm Must Sound - 496162 Location: on the dash, in direct view of the operator. The backup alarm must sound when the forklift is placed in reverse gear. No Riders - 420732 Location: on the cab entrance(s), and on or near wheel fenders and engine cover. Informs: riders are not allowed on the forklift. Clear of Raised Boom - 801006 (Boom equipped models). Location: on both sides of the boom nose. Keep away from unsupported boom. Clear of Power Lines - 801007 (Boom equipped models). Location: on both sides of the boom nose. Keep away from power lines. XI INTRODUCTION TO SAFETY CONTENTS SAFETY DECALS Use of Frame Leveling - 801013 (Boom equipped models). Location: to the right of the operator near the hydraulic control lever. Frame leveling notice; load must be lowered. Attachment and Boom Safety - 801009 (Boom equipped models). Location: on both sides of the boom nose. Important reminders of attachment and boom safety. Hydraulic Coupling - 234805 Location: near the quick-disconnect adapters. Stop the engine and release hydraulic pressure before changing attachments. Rotating Fan and Belt(s) - 801008 Location: on the radiator near the fan, and on any fan belt/pulley cover(s). Keep hands and clothing away from rotating fan and belts. XII INTRODUCTION TO SAFETY CONTENTS SAFETY DECALS Gear Shift Pattern - 33460 (4-speed transmission models). Location: near the gear shift lever. Identifies the gear shift pattern of the forklift transmission. Steering Mode - 184276 (4 wheel steer equipped models). Location: near the steering mode selection lever. Identifies the steering mode selection. 221322 Mineral Oil (Brake Reservoir) - 221322 or 234800 has been replaced by 164091. Location: near the brake fluid reservoir where applicable. Refer to the Operator/Service Manual for the correct brake fluid (mineral oil) to be used in the brake system. 234800 XIII INTRODUCTION TO SAFETY CONTENTS SAFETY DECALS Hydraulic Oil - 234798 or 76573 Location: on the hydraulic tank or filler cap. Identifies the hydraulic reservoir (tank) or filler cap. Hydraulic Oil - 61024 Location: on the hydraulic tank. Identifies the hydraulic reservoir (tank). Anti-Freeze - 234799 Location: on the radiator, near the radiator filler cap. Indicates required minimum to maximum anti-freeze protection (-220F to -400F). Diesel Fuel - 161101 Location: on the fuel tank, near the filler cap. Identifies the fuel tank, and use of diesel fuel. No Step - 496735 Location: varies, depending on the forklift model. Instructs personnel not to use the designated area as a step. Do Not Tow - 494918 (Hydrostatic equipped models). Location: on the dash, in view of the operator. Towing the forklift will damage the transmission; refer to the operator’s manual. XIV INTRODUCTION TO SAFETY CONTENTS SAFETY DECALS Attachment Warning - 421016 (Boom equipped models). Location: on the boom coupler, near where the retaining shaft is installed. Reminder to operator; install attachment retaining shaft and safety pin before operations. Hook Here - 24653 Location: at points provided on the forklift, where straps or chains may be attached to secure the forklift to a trailer during transport. Fork Safety - 426641 (Mast equipped models). Location: on the front and back side of the mast’s outer rails, at eye level (4 required). Instructs personnel not to travel beneath or upon the lift truck forks. Pinch Point, Large, 2.5 x 4.5 in. - 426643 Pinch Point, Small, 1.5 x 2.75 in. - 426642 (Mast equipped models). Location: on the front and rear sides of the mast cross bracing. Keep fingers away from the mast crossbracing. HAND THROTTLE DANGER - 804784 (Boom equipped models, option). Location: Near the hand throttle mechanism. Reminder to operator; set parking brake before operating hand throttle. Disengage hand throttle before leaving the forklift. XV INTRODUCTION TO SAFETY CONTENTS SAFETY DECALS Acid in Battery - 801014 Location: in or near the battery storage compartment. Addresses battery hazards. Jump Start Battery - 801015 Location: in or near the battery storage compartment. Jump start instructions. Attachment Plate - 425995 Location: on the optional removeable forklift attachment. Important manufacturer information about the attachment. Record this information for use when contacting the maufacturer for parts and service. Overhead Guard Data Plate - B6109 Location: attached to the overhead guard. Overhead guard conformity. 496550 Forklift Data Plate - 496550 (Boom equipped models) Forklift Data Plate - 496538 (Mast equipped models) Location: within the operator’s compartment. Important forklift truck identification. Record this information for use when contacting the manufacturer for parts and service. XVI 496538 INTRODUCTION TO SAFETY CONTENTS 1 - OPERATING AND SAFETY INSTRUCTIONS 2 - DESCRIPTION 3 - MAINTENANCE 4 - ADAPTABLE ATTACHMENTS IN OPTION ON THE RANGE THE TEXTS AND ILLUSTRATIONS IN THIS DOCUMENT MAY NOT BE REPRODUCED EITHER WHOLLY OR IN PART. XV INTRODUCTION TO SAFETY CONTENTS INTRODUCTION TO SAFETY CONTENTS 1 - OPERATING AND SAFETY INSTRUCTIONS 1-1 INTRODUCTION TO SAFETY CONTENTS 1-2 INTRODUCTION TO SAFETY CONTENTS TABLE OF CONTENTS INSTRUCTIONS 1-4 TO THE COMPANY MANAGER THE OPERATOR THE LIFT TRUCK A - THE LIFT TRUCK'S SUITABILITY FOR THE JOB B - ADAPTATION OF THE LIFT TRUCK TO STANDARD ENVIRONMENTAL CONDITIONS C - MODIFICATION OF THE LIFT TRUCK INSTRUCTIONS MAINTENANCE INSTRUCTIONS 1-6 FOR THE OPERATOR GENERAL INSTRUCTIONS A - OPERATOR'S MANUAL B - AUTHORIZATION FOR USE C - MAINTENANCE D - MODIFICATION OF THE LIFT TRUCK E - LIFTING PEOPLE OPERATING INSTRUCTIONS UNLADEN AND LADEN A - BEFORE STARTING THE LIFT TRUCK B - DRIVER’S OPERATING INSTRUCTIONS C - ENVIRONMENT D - VISIBILITY E - STARTING THE LIFT TRUCK F - DRIVING THE LIFT TRUCK G - STOPPING THE LIFT TRUCK H - DRIVING THE LIFT TRUCK ON THE PUBLIC HIGHWAY INSTRUCTIONS FOR HANDLING A LOAD A - CHOICE OF ATTACHMENTS B - MASS OF LOAD AND CENTER OF GRAVITY C - N/A D - HORIZONTAL ATTITUDE OF THE LIFT TRUCK E - TAKING UP A LOAD FROM THE GROUND F - TAKING UP AND LAYING A HIGH LOAD ON TIRES MAINTENANCE 1-6 1-6 1-6 1-6 1-6 1-6 1-6 1-6 1-7 1-7 1-8 1-8 1-9 1-9 1 - 10 1 - 11 1 - 11 1 - 11 1 - 11 1 - 12 1 - 13 1 - 15 INSTRUCTIONS OF THE LIFT TRUCK GENERAL INSTRUCTIONS MAINTENANCE LUBRICANT AND FUEL LEVELS HYDRAULIC ELECTRICITY WELDING WASHING THE LIFT TRUCK IF THE 1-4 1-4 1-4 1-4 1-4 1-5 1-5 1 - 15 1 - 15 1 - 15 1 - 15 1 - 15 1 - 15 1 - 16 LIFT TRUCK IS NOT TO BE USED FOR A LONG TIME 1 - 17 INTRODUCTION PREPARING THE LIFT TRUCK PROTECTING THE I.C. ENGINE PROTECTING THE LIFT TRUCK BRINGING THE LIFT TRUCK BACK INTO SERVICE 1 - 17 1 - 17 1 - 17 1 - 17 1 - 18 1-3 INTRODUCTION TO SAFETY CONTENTS INSTRUCTIONS TO THE COMPANY MANAGER THE OPERATOR - Only qualified, authorized personnel may operate the lift truck. The authorization is to be given to the operator in writing by the company manager. Authorization must be carried by the operator during all operations. WARNING On the basis of experience, there are a number of possible situations in which operating the lift truck is prohibited. Such foreseeable abnormal uses, the main ones being listed below, are strictly forbidden. - The foreseeable abnormal behavior of neglect, but not intending to put the machinery to any improper use. - The reflex reactions of a person in the event of a malfunction, incident, fault, etc. during operation of the lift truck. - Behavior resulting from application of the "principle of least action" when performing a task. - For certain machines, the foreseeable behavior of such persons as unauthorized: apprentices, teenagers, handicapped persons and trainees tempted to drive a lift truck. Truck drivers tempted to operate a truck to win a bet, in competition or for their own personal experience. The person in charge of the equipment must take these criteria into account when assessing whether or not a person will make a suitable driver. THE LIFT TRUCK A - THE LIFT TRUCK'S SUITABILITY FOR THE JOB - MANITOU has ensured that this lift truck is suitable for use under the standard operating conditions defined in this operator's manual, in accordance to ASME B56.6 - 2002. - Before commissioning, the company manager must make sure that the lift truck is appropriate for the work to be done, and perform tests as required (in accordance with current legislation). B - ADAPTATION OF THE LIFT TRUCK TO STANDARD ENVIRONMENTAL CONDITIONS - In addition to standard equipment mounted on your lift truck, additional options are available : road lighting, stop lights, flashing light, reverse lights, front light, rear light, light at the boom head, etc. - The operator must take into account the operating conditions to determine the lift truck's signalling and lighting equipment requirements. Contact your dealer. - Take into account climatic and atmospheric conditions of the work site. . Protection against frost (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL). . Adaptation of lubricants (ask your dealer for information). . I.C. engine filtration (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). IMPORTANT For operation under average climatic conditions, i.e. between -15 °C and + 35 °C (5° to 95°F), correct levels of lubricants in all the circuits are provided in production. For operation under more severe climatic conditions, before starting up, it is necessary to drain all the circuits, then add the correct levels of lubricants properly suited to the relevant ambient temperatures. It is the same for the cooling fluid (Contact your dealer for information, if necessary). - A lift truck operating in an area without fire extinguishing equipment must be equipped with an individual extinguisher, consult your dealer. WARNING Your lift truck is designed for outdoor use under normal atmospheric conditions and indoor use in suitably aerated and ventilated premises. It is prohibited to use the lift truck in areas where there is a risk of fire or which are potentially explosive (i.e. refineries, fuel or gas depots, stores of inflammable products…). For use in these areas, specific equipment is available (ask your dealer for information). C - MODIFICATION OF THE LIFT TRUCK - For your safety and that of others, you must not change the structure or settings of the various components used on your lift truck (i.e. hydraulic pressure, calibrating limiters, I.C. engine speed, addition of extra equipment, addition of counterweight, unapproved attachments, etc.). The manufacturer cannot be held responsible for unauthorized modifications. - Our trucks comply with Directive 89/336/EC concerning electromagnetic compatibility (EMC), and with the corresponding harmonized norm EN 12895. Their proper operation is no longer guaranteed if they are used within areas in which the electromagnetic fields exceed the limit specified by that norm (10 V/m). - Directive 2002/44/EC requires company managers to not expose their employees to excessive vibration doses. There is no recognized code of measurement for comparing the machines of different manufacturers. The actual doses received can therefore be measured only under actual operating conditions at the user's premises. - The following are some tips for minimizing these vibration doses: • Select the most suitable lift truck and attachment for the intended use. • Adapt the seat adjustment to the operator's weight (according to lift truck model) and maintain it in good condition, as well as the cab suspension. Inflate the tires in accordance with recommendations. • Ensure that the operators adapt their operating speed to suit the conditions on site. • As far as possible, arrange the site in such a way as to provide a flat running surface and remove obstacles and harmful potholes. 1-4 INTRODUCTION TO SAFETY CONTENTS INSTRUCTIONS - The operator's manual must always be in good condition and kept in the place provided on the lift truck and in the language used by the operator. - The operator's manual and any plates or decals which are no longer legible or are damaged, must be replaced immediately. MAINTENANCE - Maintenance or repairs other than those detailed in part : 3 - MAINTENANCE must be carried out by qualified personnel (consult your dealer) and under the necessary safety conditions to maintain the health of the operator and any third party. WARNING Your lift truck must be inspected periodically to ensure that it remains in compliance. The frequency of this inspection is defined by current legislation in the country in which the lift truck is used. 1-5 INTRODUCTION TO SAFETY CONTENTS INSTRUCTIONS FOR THE OPERATOR DANGER The risk of accident while operating, servicing or repairing your lift truck can be reduced if you follow the safety instructions and safety measures detailed in this manual. Failure to respect the safety and operating instructions, or the instructions for repairing or servicing your lift truck can lead to serious injury or fatal accident. - Only the operations and maneuvers described in this operator's manual may be performed. The manufacturer cannot predict all possible situations of risk. Consequently, the safety instructions given in the operator's manual and on the lift truck itself are not conclusive. - At any time, as an operator, you must envision, within reason, the possible risk to yourself, to others or to the lift truck itself during use. GENERAL INSTRUCTIONS A - OPERATOR'S MANUAL - Read the operator's manual carefully. - The operator's manual must always be kept good condition and in the place provided on the lift truck. - You must report any plates and decals which are no longer legible or are damaged. B - AUTHORIZATION FOR USE - Only qualified, authorized personnel may operate the lift truck. This authorization is given in writing by the company manager, in charge of using the lift truck, and must be carried by the operator during operations. - The operator is not authorized to allow others to operate the lift truck. C - MAINTENANCE - The operator must notify his manager immediately if his lift truck is not in good working order or does not comply with the safety standards. - The operator is prohibited from performing repairs or adjustments, unless he has been trained for this purpose. He must keep the lift truck properly cleaned if this is among his responsibilities. - The operator must carry out daily maintenance (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE). - The operator must ensure that the tires are suited for the work site. (There are optional solutions, consult your dealer.) . SAND tires. . LAND tires. . Snow chains. DANGER Do not operate the lift truck if the tires are incorrectly inflated, damaged or excessively worn, Bad tires can put your safety or that of others at risk, or cause damage to the lift truck. The installation of foam inflated tires is prohibited and is not guaranteed by the manufacturer (prior authorization is required). D - MODIFICATION OF THE LIFT TRUCK - For your safety and others, you must not change the structure or settings of the various components used on your lift truck (hydraulic pressure, calibrating limiters, I.C. engine speed, addition of extra equipment, addition of counterweight, unapproved attachments, etc.). The manufacturer cannot be held responsible for such modifications. E - LIFTING PEOPLE - The use of working equipment and load lifting attachments to lift personnel is strictly forbidden. OPERATING INSTRUCTIONS UNLADEN AND LADEN A - BEFORE STARTING THE LIFT TRUCK - Perform daily maintenance (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE). - Make sure the lights, indicators and windshield wipers are working properly. - Make sure the rear view mirrors are in good condition, clean and properly adjusted. - Make sure the horn and backup alarm works properly. 1-6 INTRODUCTION TO SAFETY CONTENTS B - DRIVER’S OPERATING INSTRUCTIONS - The operator is advised to familiarize himself with the position and operation of all controls and instruments before operating the lift truck. - Wear clothes suited for driving the lift truck, avoid loose clothing. - Make sure you have the appropriate protective equipment for the job to be done. - Prolonged exposure to high noise levels may cause hearing problems. It is recommended to wear ear muffs to protect against excessive noise. - Always pay attention when using the lift truck. Do not listen to the radio or music using headphones or earphones. - Never operate the lift truck when hands or feet are wet or slippery. - For increased comfort, adjust the seat to your requirements, adopt a comfortable reach of the forklift controls. CAUTION Under no circumstances should the seat be adjusted while the lift truck is moving. - The operator must always be properly seated in the driver’s cab. It is prohibited to have arms, legs, or generally any part of the body, protruding from the cab of the lift truck. - The safety belt must be worn, adjusted to the operator's size. - The control levers must never be used for climbing onto or down from the lift truck, etc. - If any of the control components are fitted with an engagement device (manual throttle, etc.), it is forbidden to leave the cab without first placing these controls in neutral. - Never carry passengers on the lift truck or in the cab. C - ENVIRONMENT - Always comply with all work site safety regulations. - If you have to use the lift truck in a dark area or at night, make sure it is equipped with working lights. - During handling operations, make sure that no one is in the way of the lift truck or its load. - Do not allow personnel to come near the working area of the lift truck or pass beneath an elevated load. - When using the lift truck on an incline, before lifting the boom, follow the instructions given in the Section : INSTRUCTIONS FOR HANDLING A LOAD : D - HORIZONTAL ATTITUDE OF THE LIFT TRUCK. - Travelling on a longitudinal slope : • Drive and brake gently. • Moving without load : Forks or attachment facing downhill. • Moving with load : Forks or attachment facing uphill. - Never move onto a loading platform without having first checked : • That it is suitably positioned and made secure. • That the unit to which it is connected (tractor, etc.) will not shift. • That the platform is approved for the total weight of the lift truck to be loaded. • That the platform is approved for the overall size of the lift truck. - Never move onto a foot bridge, floor or freight lift, without being certain that they are approved for the weight and size of the lift truck to be loaded and without having checked that they are in sound working order. - Be extra careful maneuvering around loading bays, trenches, scaffolding, soft terrain and manholes. - Make sure the ground is stable and firm under the wheels and/or stabilizers before lifting or removing the load. If necessary, add sufficient wedging under the stabilizers (where applicable). - Make sure that the scaffolding, loading platform, pilings or ground is capable of bearing the load. - Never stack loads on uneven or soft ground, they may tip over. - When working near power lines, ensure that the safety distance is sufficient between the working area of the lift truck and the power lines. DANGER You must consult your local electrical agency. You could be electrocuted or seriously injured if you operate or park the lift truck too close to power lines. DANGER During high winds do not attempt moving loads that may catch the wind or cause the fork lift to be unstable. WARNING When holding a load or attachment above a structure for a long time, there is risk of the boom descending due to the oil in the cylinders cooling down. To eliminate this risk: - Regularly check the distance between the load or the attachment and the structure and re-adjust as necessary. - If possible use the lift truck at an oil temperature as close as possible to ambient temperature. 1-7 INTRODUCTION TO SAFETY CONTENTS D - VISIBILITY - The safety of people within the lift truck's working area, as well as that of the lift truck itself and the operator depend on good operator visibility of the lift truck's immediate vicinity in all situations and at all times. - This lift truck has been designed to allow good operator visibility (direct or indirect by means of rear-view mirrors) of the immediate vicinity of the lift truck while traveling with no load and with the boom in the transport position. - Special precautions must be taken if the size of the load restricts visibility, such as: - moving in reverse, - site layout, - assisted by a person directing the maneuver (while standing outside the truck's area of travel), making sure to keep this person clearly in view at all times. - in any case, avoid reversing over long distances. - Certain special accessories may require the truck to travel with the boom in the raised position. In such cases, visibility on the right hand side is restricted, and special precautions must be taken: - site layout, - assisted by a person directing the maneuver (while standing outside the truck's area of travel). - If visibility of your road is inadequate, ask someone to assist by directing the maneuver (while standing outside the truck's area of travel), making sure to keep this person clearly in view at all times. - Keep all components affecting visibility in a clean, properly adjusted state and in good working order (e.g. windscreens, windows, windscreen wipers, windscreen washers, driving and work lights, rear-view mirrors). E - STARTING THE LIFT TRUCK SAFETY NOTICE WARNING The lift truck must be started or maneuvered only when the operator is sitting in the driver’s cab, his seat belt fastened and properly adjusted. - Never try to start the lift truck by pushing or towing it, such operation will cause severe damage to the transmission. If necessary, to tow the lift truck in an emergency, the transmission must be placed in the neutral position (see : 3 MAINTENANCE : G - OCCASIONAL MAINTENANCE). - If using an emergency battery for start-up, use a battery with the same specifications. Insure correct battery polarity (+ or -) when connecting to it. Connect at first the positive terminals before the negative terminals. WARNING Failure to respect polarity between batteries can cause serious damage to the electrical circuit. The electrolyte in the battery may produce an explosive gas. Avoid flames and generation of sparks close to the batteries. Never disconnect a battery while it is charging. INSTRUCTIONS - Insure the hood(s) are properly secured and locked in place. - Make sure that the forward/reverse lever is in neutral. - Turn the ignition key to the position I to activate the electrical system. - Make sure the signal lights on the instrument control panel and fuel level indicators are working properly (see : 2 DESCRIPTION : INSTRUMENTS AND CONTROLS). - Turn the ignition key to position II to preheat for 15 seconds, then turn the ignition key fully : the I.C. engine should then start. Release the ignition key and let the I.C. engine run at idle. - Do not engage the starter motor for more than 15 seconds and perform preheating for 10 seconds between unsuccessful starting attempts. - Insure all signal lights on the instrument control panel go off before driving the forklift. - Check all instruments and controls again after the I.C. engine is warm and at frequent intervals during use. - If an instrument does not show the correct display, safely park the forklift and stop the I.C. engine. Report the problem immediately and make necessary arrangements for repair or service. 1-8 INTRODUCTION TO SAFETY CONTENTS F - DRIVING THE LIFT TRUCK SAFETY NOTICE DANGER Operators' attention is drawn to the risks involved in using the lift truck, in particular : - Risk of losing control. - Risk of losing lateral and frontal stability of the lift truck. The operator must remain in control of the lift truck. In the event of the lift truck overturning, do not try to leave the cab during the incident. YOUR BEST PROTECTION IS TO STAY FASTENED IN THE CAB. - Do not perform operations which exceed the capacities of your lift truck or attachments. - Always drive the lift truck with the forks or attachment in the transport position, i.e. at 12 in. above the ground, the boom retracted and the carriage sloping backwards. - Carry only loads which are balanced and properly secured to avoid any risk of a load falling off. - Ensure that pallets, cases, etc, are in good order and suitable for the load to be lifted. - Familiarize yourself with the lift truck on the terrain where it will be used. - Ensure that the service brakes are working properly. - The loaded lift truck must not travel at speeds in excess of 7mph. - Drive smoothly at an appropriate speed for the operating conditions (land configuration, load on the lift truck). - Do not use the hydraulic boom controls while the lift truck is moving. - Do not maneuver the lift truck with the boom in the raised position unless under exceptional circumstances and then with extreme caution, at very low speed and using gentle braking. Ensure that visibility is adequate. - Take turns slowly. - In all circumstances make sure you are in control of your speed. - On damp, slippery or uneven terrain, drive slowly. - Brake gently, never abruptly. - Use the lift truck’s forward/reverse lever from a stationary position only and never abruptly. - Do not drive with your foot on the brake pedal or with the parking brake on. - Always remember that hydrostatic type steering is extremely sensitive to movement of the steering wheel, turn it gently and not abruptly. - Never leave the I.C. engine running while the lift truck is unattended. - Do not leave the cab while the lift truck has a raised load. - Watch where you are going and always make sure you have good visibility along the route. - Use the rear-view mirrors frequently. - Drive around obstacles. - Never drive on or along the edge of a ditch or steep slope. - It is dangerous to use two lift trucks simultaneously to handle heavy or over-sized loads, do not attempt such operations, always procure the proper equipment for the job. INSTRUCTIONS - Always drive the lift truck with the forks or attachment to the transport position, i.e. at 12 in. from the ground, the boom retracted and the carriage sloping backwards. - Select the appropriate steering mode for the working conditions. - Shift the forward/reverse lever to the desired direction of travel. - Release the parking brake and accelerate gradually until the lift truck moves off. G - STOPPING (PARKING) THE LIFT TRUCK SAFETY NOTICE - When the lift truck is stationary, or if the operator has to leave his cab (even for a moment), place the forks or attachment on the ground, apply the parking brake and place the forward/reverse lever in neutral. - Make sure that the lift truck is not parked in any position that will interfere with the traffic flow and at least 3.5 ft from the track of a railway. - For prolonged parking on site, protect the lift truck from bad weather, particularly from frost (check the level of antifreeze), close and lock all lift truck accesses (door, window, engine compartment…). INSTRUCTIONS - Park the lift truck on flat ground or on an incline of less than 15 %. - Place the forward/reverse lever in neutral. - Apply the parking brake. - Completely retract the boom. - Lower the forks or attachment to rest on the ground. - When using an attachment with a grab or jaws, or a bucket with hydraulic opening, close the attachment completely. - Before stopping the lift truck after a hard working period, let the I.C. engine idle for a few moments, allowing the coolant and oil to lower the temperature of the I.C. engine and transmission. Do not neglect this precaution : in the event of frequent stops or stopping a hot I.C. engine, the temperature of certain parts will rise significantly, with the risk of badly damaging such parts. - Stop the I.C. engine. - Remove the ignition key. - Make sure all means of access to the lift truck are closed and locked (door, window, engine compartment…). 1-9 INTRODUCTION TO SAFETY CONTENTS H - DRIVING THE LIFT TRUCK ON THE PUBLIC HIGHWAY SAFETY INSTRUCTIONS - Operators driving on the public highway must comply with all current highway codes. - The lift truck must also comply with all current road use codes. If necessary, there are optional solutions. Contact your dealer. INSTRUCTIONS - Make sure the revolving light is in place, switch it on and verify its operation. - Check for the good working order and cleanness of lights, indicators and windshield wiper. - Switch off the overhead work lights if the lift truck is equipped with them. - Select the steering mode "HIGHWAY TRAFFIC" (see : 2 - DESCRIPTION : INSTRUMENTS AND CONTROLS). - Retract the boom completely and place the attachment at 12 in. above the ground. - Place the frame in the level or central position (as per model of lift truck). - Lift the stabilizers to the maximum and turn the blocks inward (as per model of lift truck). DANGER Do not allow the lift truck to coast in neutral (using either the forward/reverse lever, gear shift lever or transmission cut-off button). Coasting on a slope will lead to excessive speed which may make the lift truck uncontrollable (steering, brakes) and may cause serious mechanical damage. DRIVING THE LIFT TRUCK WITH A FRONT-MOUNTED ATTACHMENT - You must comply with current regulations in your country, covering the possibility of driving on the public highway with a frontmounted attachment on your lift truck. - If highway legislation in your country authorizes road use with a front-mounted attachment, you must at least : • Protect and label any sharp and/or dangerous edges on the attachment (see : 4 - ADAPTABLE ATTACHMENTS IN OPTION ON THE RANGE : ATTACHMENT SHIELDS). • The attachment must not be loaded. • Make sure that the attachment does not mask the lighting range of the forward lights. • Make sure that highway legislation in your country does not require other obligations. OPERATING THE LIFT TRUCK WITH A TRAILER - When using a trailer, observe the regulations in your country (maximum travel speed, braking, maximum weight of trailer, etc.). - Do not forget to connect the trailer’s electrical equipment to that of the lift truck. - The trailer's braking system must comply with current legislation. - If pulling a trailer with assisted braking, the lift truck must be equipped with a trailer braking mechanism. In this case, do not forget to connect the trailer braking equipment to the lift truck. - The maximum vertical pull on the trailer hook must not exceed 3350 ft/lbs. - The authorized maximum weight must not exceed the maximum weight authorized by the manufacturer (consult the manufacturer’s plate on your lift truck). IF NECESSARY, CONSULT YOUR DEALER. 1 - 10 INTRODUCTION TO SAFETY INSTRUCTIONS CONTENTS FOR HANDLING A LOAD A - CHOICE OF ATTACHMENTS - Only attachments approved by MANITOU can be used on its lift trucks. - Make sure the attachment is appropriate for the work to be done (see : 4 - ADAPTABLE ATTACHMENTS IN OPTION ON THE RANGE). - Make sure the attachment is correctly installed and locked onto the lift truck carriage. - Make sure that your lift truck attachments work properly. - Comply with the load chart limits for the lift truck and attachment used. - Do not exceed the rated capacity of the attachment. - Never lift a load in a sling without the attachment provided for the purpose. There are optional solutions; contact your dealer. B - MASS OF LOAD AND CENTER OF GRAVITY - Before taking up a load, you must know its mass and center of gravity. - The load chart for your lift truck is valid for a load in which the position of the center of gravity is 24 in. from the base of the forks (fig. B1). For a higher center of gravity, contact your dealer. - For irregular loads, determine the center of gravity before any movement (fig. B2) and set it in the longitudinal axis of the lift truck. B1 24 IN. 500 mm CAUTION Do not attempt to move a load heavier than the effective capacity defined on the lift truck load chart. CAUTION For loads with a moving center of gravity (i.e., liquids), take into account the variations of the center of gravity in order to determine the load to be handled (Consult your agent or dealer). Be vigilant and take extra care to limit these variations as much as possible. C - N/A D - TRANSVERSE (LEVEL) ATTITUDE OF THE LIFT TRUCK The transverse (level) attitude is the angle of tilt of the chassis with respect to the horizontal. Raising the boom while on a slope reduces the lift truck's lateral stability . The transverse attitude must be set with the boom in the down position as follows: 1 - LIFT TRUCK WITHOUT SLOPE CORRECTOR (FRAME LEVELING) USED ON TIRES - Position the lift truck so that the bubble in the level is between the two lines (see : 2 DESCRIPTION : INSTRUMENTS AND CONTROLS). 1 - 11 B2 INTRODUCTION TO SAFETY CONTENTS E - TAKING UP A LOAD FROM THE GROUND - Position the lift truck perpendicular to the load, with the boom retracted and the forks in a horizontal position (fig. E1). - Adjust the fork spread and centering in alignment with the load (fig. E2) (optional solutions exist, consult your dealer). - Never lift a load with a single fork. E1 CAUTION Beware of the risks of pinching or crushing limbs when manually adjusting the forks. E2 - Move the lift truck forward slowly (1) and bring the forks to the front of the load (fig. E3), if necessary, slightly lift the boom (2) while taking up the load. - Bring the load into the transport position. - Tilt the load far enough backwards to ensure stability (to avoid loss of load while braking). FOR A NON-PALLETIZED LOAD - Tilt the carriage (1) forwards and move the lift truck slowly forwards (2), insert the forks under the load (fig. E4) (block the load if necessary). - Continue to move the lift truck forwards (2) tilting the carriage (3) (fig. E4) backwards to position the load on the forks. Check the load's longitudinal and lateral stability. E3 1 2 E4 2 3 1 - 12 1 INTRODUCTION TO SAFETY CONTENTS F - TAKING UP AND LAYING A HIGH LOAD ON TIRES F1 WARNING Do not raise the boom until you have first checked the level attitude of the lift truck (see : INSTRUCTIONS FOR HANDLING A LOAD : D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK). 2 1 REMINDER : Make sure that the following operations can be performed with clear visibility (see : OPERATIONS INSTRUCTIONS UNLADEN AND LADEN : D - VISIBILITY). 3 TAKING UP A HIGH LOAD ON TIRES - Ensure that the forks will easily pass under the load. - Lift and extend the boom (1) (2) until the forks are level with the load, moving the lift truck (3) forward if necessary (fig. F1), moving very slowly and carefully. - Keep the shortest distance possible to place the forks under the load, between the pile and the lift truck (fig. F1) and use the shortest possible length of boom. - Place the forks in front of the load by alternately extending and retracting the boom (1) or, if necessary, moving the lift truck forward (2) (fig. F2). Set the parkbrake and place the forward/reverse gear to neutral. - Slightly lift the load (1) and incline the carriage (2) backwards to stabilize the load (fig. F3). - Tilt the load sufficiently backwards to ensure its stability. - Respect load capacites (see : INSTRUCTIONS FOR HANDLING A LOAD). If the lift truck is overloaded, return the load to the place from which it was taken. - If possible lower the load without shifting the lift truck. Lift the boom (1) to raise the load, retract (2) and lower the boom (3) to bring the load into the transport position (fig. F4). - If this is not possible, back the lift truck (1), maneuvering very gently and carefully to remove the load. Retract (2) and lower the boom (3) to bring the load into the transport position (fig. F5). F2 1 2 F3 2 1 F4 1 2 3 F5 2 3 1 1 - 13 INTRODUCTION TO SAFETY CONTENTS LAYING A HIGH LOAD ON TIRES - Approach with the load in the transport position, aligning to the front of the pile (fig. F6). - Set the handbrake and place the forward/reverse lever in neutral. - Lift and extend the boom (1) (2) until the load is above the pile, respect load capacites (see : INSTRUCTIONS FOR HANDLING A LOAD). If necessary, move the lift truck (3) forward (fig. F7), driving very slowly and carefully. - Adjust the load to a horizontal position and place it on the pile by lowering and retracting the boom (1) (2) until the load is stabilized (fig. F8). - If possible, release the forks by alternately retracting and raising the boom (1) (fig. F9). Then move the forks into transport position. - If this is not possible, back the lift truck (1) very slowly and carefully to release the forks (fig. F10). Then move the forks into transport position. F6 F7 2 1 3 F8 1 2 F9 1 F10 1 1 - 14 INTRODUCTION TO SAFETY CONTENTS MAINTENANCE INSTRUCTIONS OF THE LIFT TRUCK GENERAL INSTRUCTIONS - Ensure the area is sufficiently ventilated before starting the lift truck. - Wear clothes suitable for the maintenance of the lift truck, avoid wearing jewelry and loose clothing. Tie and protect your hair, if necessary. - Stop the I.C. engine and remove the ignition key, when service is necessary. - Read the operator's manual carefully. - Perform all necessary repairs immediately, including minor repairs. - Repair all leaks immediately, including minor leaks. - Insure disposal of all used materials and spare parts are carried out in a safe and ecological manner. - Beware of the risk of burns and/or splashing of components while servicing the lift truck (engine/exhaust, radiator, fluids, etc.). MAINTENANCE - Perform periodic services (see: 3 - MAINTENANCE) to keep your lift truck in good working conditions. Failure to perform the periodic services may cancel warranty. LUBRICANT AND FUEL LEVELS - Use the recommended lubricants (never use contaminated lubricants). - Do not fill the fuel tank while the I.C. engine is running. - Fill the fuel tank only in areas specified for this purpose. - Do not fill the fuel tank to the maximum level. - Do not smoke or approach the lift truck with a flame, while the fuel tank is open or is being filled. HYDRAULIC - Do not attempt to loosen connections of hoses or any hydraulic component with the circuit under pressure. WARNING BALANCING VALVE : For inspection, see : 3 – MAINTENANCE : D - EVERY 500 HOURS SERVICE. It is dangerous to change the setting or remove the balancing valves or safety valves which may be fitted to your lift truck cylinders. These operations must only be performed by approved personnel (consult your dealer). WARNING The HYDRAULIC ACCUMULATORS which may be fitted on your lift truck, are under high pressure, it is dangerous to dismantle them. This operation must only be performed by approved personnel (consult your dealer). ELECTRICITY DANGER - Do not short-circuit the starter relay to start the lift truck. If the forward/reverse gear is not in neutral, the lift truck will start to move immediately! - Do not drop metallic objects on the battery. - Disconnect the battery before working on the electrical circuit. WELDING - Always disconnect the battery before performing welding operations on the lift truck. - When welding on the lift truck, connect the negative cable from the welding equipment directly to the part being welded, so as to avoid high tension current passing through the alternator. - Never perform welding or work which directs heat onto an inflated tire. The heat may increase the air pressure which can cause the tire to explode. - If the lift truck is equipped with an electronic control unit, disconnect it before welding, to avoid the risk of causing irreparable damage to electronic components. 1 - 15 INTRODUCTION TO SAFETY WASHING CONTENTS THE LIFT TRUCK - Clean the lift truck before servicing. - Remember to close and lock all access to the lift truck (door, window(s), engine compartment…). - During washing, avoid the articulations, electrical components and connections. - Protect components susceptible of being damaged against penetration of water, steam or cleaning agents, particularly electrical components, hose connections and the fuel injection pump. - Remove any residue of fuel, oil or grease from the lift truck. FOR ANY INTERVENTION OTHER THAN REGULAR MAINTENANCE, CONSULT YOUR DEALER. 1 - 16 INTRODUCTION TO SAFETY CONTENTS IF THE LIFT TRUCK IS NOT TO BE USED FOR A LONG TIME INTRODUCTION The following recommendations are intended to prevent damage to the lift truck while it is removed from service for an extended period of time. IMPORTANT PREPARING It is recommended that your dealer perform the following procedures for lift truck storage and returning it to service. THE LIFT TRUCK - Clean the lift truck thoroughly. - Check for and repair any fuel, oil, water or air leaks. - Replace or repair any worn or damaged parts. - Wash the painted surfaces of the lift truck with clear, cold water and dry them. - Touch up the paint where necessary. - Park the lift truck (see : OPERATING INSTRUCTIONS UNLADEN AND LADEN). - Make sure the boom cylinder rod ends are all in retracted position. - Release the pressure in the hydraulic circuits. PROTECTING THE I.C. ENGINE - Fill the tank with fuel (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE). - Empty and replace the antifreeze (see : 3 - MAINTENANCE : F - EVERY 2000 HOURS SERVICE). - Allow the I.C. engine to run at idle for a few minutes, then switch off. - Replace the I.C. engine oil and oil filter (see : 3 - MAINTENANCE : D - EVERY 500 HOURS SERVICE). - Add a preservative product to the engine oil. - Run the I.C. engine for a short time so that the oil and cooling liquid circulate. - Disconnect the battery and store it in a safe place away from the cold, after charging it to a maximum. - Remove the injectors and spray a protective product into each cylinder for two seconds with the piston in low neutral position. - Turn the crankshaft once slowly and refit the injectors (see I.C. engine REPAIR MANUAL). - Remove the intake hose from the manifold or turbocharger and spray the protective product into the manifold or turbocharger. - Cap the intake manifold or turbocharger hole with waterproof adhesive tape. - Remove the exhaust pipe and spray the protective product into the exhaust manifold or turbocharger. - Refit the exhaust pipe and block the outlet with waterproof adhesive tape. NOTE : The spray time is noted on the preservative packaging and must be increased by 50% for turbo engines. - Open the oil filler plug, spray the protective product around the rocker arm shaft and install the filler plug. - Cap the fuel tank using waterproof adhesive tape. - Remove the drive belts and store them in a safe place. - Disconnect the engine cut-off solenoid on the injection pump and carefully insulate the connection. PROTECTING THE LIFT TRUCK - Set the lift truck on axle stands so that the tires are not in contact with the ground and release the parkbrake. - Protect all exposed cylinder rods from corrosion. - Cover the tires. NOTE : If the lift truck is to be stored outdoors, cover it with a waterproof covering. 1 - 17 INTRODUCTION TO SAFETY BRINGING CONTENTS THE LIFT TRUCK BACK INTO SERVICE - Remove the waterproof adhesive tape from all the holes. - Install the intake hose. - Install and reconnect the battery. - Remove the protection from the cylinder rods. - Perform the daily service (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE). - Engage the parkbrake and remove the axle stands. - Empty and replace the fuel and fuel filter (see : 3 - MAINTENANCE : D - EVERY 500 HOURS SERVICE). - Refit and set the tension on the drive belts (see : 3 - MAINTENANCE : C - EVERY 250 HOURS SERVICE). - Turn the I.C. engine using the starter, to allow the oil pressure to rise. - Reconnect the engine cut-off solenoid. - Lubricate the lift truck components (see : 3 - MAINTENANCE : SERVICING SCHEDULE). WARNING Insure the area is adequately ventilated before starting the lift truck. - Start the lift truck following the safety instructions and regulations (see : OPERATING INSTRUCTIONS UNLADEN AND LADEN). - Run all of the boom’s hydraulic movements, verifying the full travel of each cylinder. 1 - 18 INTRODUCTION TO SAFETY CONTENTS 2 - DESCRIPTION 2-1 INTRODUCTION TO SAFETY CONTENTS 2-2 INTRODUCTION TO SAFETY CONTENTS TABLE OF CONTENTS IDENTIFICATION 2-4 OF THE LIFT TRUCK CHARACTERISTICS 2-6 DIMENSIONS 2 - 10 AND LOAD CHART INSTRUMENTS TOWING 2 - 12 AND CONTROLS 2 - 29 PIN AND HOOK DESCRIPTION AND USE OF ELECTRIC AND HYDRAULIC OPTIONS 2-3 2 - 31 CONTENTS INTRODUCTION TO SAFETY A IDENTIFICATION OF THE LIFT TRUCK Our policy is one of continual improvement of quality and value of our products, for this reason our lift trucks may receive modifications without prior notice. It is important therefore, when ordering parts or requiring any technical information, to be prepared to specify the following component information : (NOTE : For the owner's convenience it is recommended these numbers be made in the spaces provided, upon receipt of the lift truck.) PLATE B MANUFACTURER OF THE LIFT TRUCK (FIG. A) - Model Series Serial No Chassis No Year of manufacture For any further technical information regarding your lift truck refer to chapter : 2 DESCRIPTION : CHARACTERISTICS. I.C. ENGINE (FIG. B) C - I.C. engine No GEAR BOX (FIG. C) - Type - MANITOU reference - Serial No HYDROSTATIC - D) D MANITOU reference Type of codification Serial No Manufacturer’s No Year of manufacture HYDROSTATIC - PUMP (FIG. MOTOR (FIG. E) MANITOU reference Type of codification Serial No Manufacturer’s No Year of manufacture E 2-4 INTRODUCTION TO SAFETY FRONT AXLE (FIG. CONTENTS F) F - Type - Serial No - MANITOU reference REAR AXLE (FIG. G) - Type - Serial No - MANITOU reference G CAB (FIG. H) - Type - Serial No BOOM (FIG. I) - MANITOU reference - Date of manufacture H PLATE MANUFACTURER OF THE ATTACHMENT (FIG. J) - Model - Serial No - Year of manufacture I J 2-5 INTRODUCTION TO SAFETY CONTENTS CHARACTERISTICS I.C. - - ENGINE Type Number of cylinders Number of strokes Suction Injection system Ignition sequence Clearance of rocker valve (cold) . Inlet . Exhaust Capacity Bore Stroke Compression ratio Nominal rating loaded Rating slow unladen Max. rating unladen Power ISO/TR 14396 Maximum torque ISO/TR 14396 Air cleaner COOLING . Number of blades . Diameter - Thermostat . Start opening . Full opening HYDROSTATIC By water Puller 10 508 mm (20 in) 77 °C to 85 °C (180°F) 92 °C to 98 °C (203°F) TRANSMISSION HYDROSTATIC PUMP - Type - Gear reverser . Number of forward gears . Number of reverse gears - Main pump . Max./Mini displacement . Max. flow rate . Working pressure - Boost pump . Displacement . Max. flow rate . Boost pressure Max. R.P.M. HYDROSTATIC MOTOR - Type . Max./Mini displacement - Type 0,20 mm 0,45 mm 4400 cm3 105 mm 127 mm 18,2/1 2200 rpm 930 ± 20 rpm 2355 rpm 101 cv/74,5 kw 412 Nm (304 ft/lbs) at 1400 rpm Dry 3 µ CIRCUIT - Type - Fan GEAR PERKINS 1104C-44T RG81374 4 in line 4 Turbocharged Direct 1.3.4.2. MANNESMANN REXROTH A4VG71DA1D7/32R with variable cubic capacity and with automatic power governor Electromagnetic 12V 4 2 0 to 71 cm3/r (4.33 cu.in.) 170 L/mn (45 gal/mn) 470 Bar (6815 psi) 19,6 cm3 (1.2 cu.in.) 47 L/mn (12.4 gal/mn) 28 ±2 Bar (406 psi) transmission in neutral MANNESMANN REXROTH A6VM107DA2/63W with variable cubic capacity 32 to 107 cm3/r (1.95 - 6.5 cu.in.) BOX DANA 2-6 INTRODUCTION TO SAFETY FRONT AXLE - Type - Limited slip differential - Hub reducers REAR CONTENTS DANA 45 % Epicyclic AXLE - Type - Hub reducers DANA Epicyclic BRAKE - Service brake . Type - Parking brake . Type ELECTRIC Foot pedal. Hydraulic brake, applied on the front wheels. Multidisc brake immersed in oil. Mechanical hand lever applied on the front wheels. Multidisc brake immersed in oil. CIRCUIT - Earth - Battery - Alternator . Type . Tension regulator - Starter . Type Negative 12 V - 105 Ah - 680 A EN 12 V - 75 A Denso A115i Incorporated into the alternator 12 V - 3,0 kW Denso E95RL 2-7 CONTENTS INTRODUCTION TO SAFETY CHARACTERISTICS FRONT MT 1033 HL Turbo Série 2-E2 AND REAR TIRES DIMENSIONS PRESSURE 18-19,5 16PR I224 TUBELESS 5 BAR (73 PSI) 400/80-24 156A8 PIA TUBELESS 2,8 BAR (41 PSI) 14,9X24 T35 STABILARGE 18 PR 3,4 BAR (49 PSI) 400/70-20 T37 150B 14PR TUBELESS 3,3 BAR (48 PSI) 440/70-24 T37 147B TUBELESS 2,8 BAR (41 PSI) 400/80-24 T37 153B TUBELESS 3,2 BAR (46 PSI) 15,5/80-24 SGI 12PR TUBELESS 4 BAR (58 PSI) 460/70R24 IT520 150A8 TUBELESS 3,3 BAR (48 PSI) 445/70R24 MPT IT510 151G TUBELESS 4,1 BAR (60 PSI) 17,5LR24 XM27 145A8 TUBELESS 3,5 BAR (51 PSI) HYDRAULIC TIRE LOAD FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN FRONT UNLADEN FRONT LADEN REAR UNLADEN REAR LADEN 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs 3748 lbs 9921 lbs 4850 lbs 2315 lbs PRESSURE ON THE CONTACT SURFACE HARD GROUND LIGHT GROUND 48 lbs/sq in 20 lbs/sq in 84 lbs/sq in 36 lbs/sq in 56 lbs/sq in 24 lbs/sq in 37 lbs/sq in 15 lbs/sq in lbs/sq in lbs/sq in lbs/sq in lbs/sq in lbs/sq in lbs/sq in lbs/sq in lbs/sq in 81 lbs/sq in 28 lbs/sq in 132 lbs/sq in 44 lbs/sq in 92 lbs/sq in 31 lbs/sq in 73 lbs/sq in 24 lbs/sq in 105 lbs/sq in 34 lbs/sq in 149 lbs/sq in 47 lbs/sq in 112 lbs/sq in 36 lbs/sq in 94 lbs/sq in 30 lbs/sq in 91 lbs/sq in 26 lbs/sq in 134 lbs/sq in 38 lbs/sq in 98 lbs/sq in 28 lbs/sq in 78 lbs/sq in 23 lbs/sq in 104 lbs/sq in 28 lbs/sq in 145 lbs/sq in 41 lbs/sq in 112 lbs/sq in 31 lbs/sq in 90 lbs/sq in 26 lbs/sq in 112 lbs/sq in 31 lbs/sq in 169 lbs/sq in 47 lbs/sq in 125 lbs/sq in 34 lbs/sq in 104 lbs/sq in 27 lbs/sq in 119 lbs/sq in 33 lbs/sq in 169 lbs/sq in 44 lbs/sq in 134 lbs/sq in 36 lbs/sq in 121 lbs/sq in 31 lbs/sq in 121 lbs/sq in 40 lbs/sq in 142 lbs/sq in 47 lbs/sq in 125 lbs/sq in 41 lbs/sq in 111 lbs/sq in 37 lbs/sq in 23 lbs/sq in 22 lbs/sq in 47 lbs/sq in 31 lbs/sq in 28 lbs/sq in 22 lbs/sq in 16 lbs/sq in 15 lbs/sq in CIRCUIT - Type of pump . Capacity . Flow rate at 2300 rpm . Flow rate at 1600 rpm - Pressure . Lifting, tilting, telescoping, tilting corrector, attachment circuit . Steering circuit - Filtration . Return . Suction 2-8 Gear pump with flow divider 43,77 cm3 (2.67 cu in) 101 L/mn (26.7 gal/min) 70 L/mn (18.5 gal/min) 270 Bar (3915 psi) 140 Bar (2030 psi) 15 µ 125 µ AREA OF THE CONTACT SURFACE HARD GROUND LIGHT GROUND 77 sq in 182 sq in 117 sq in 276 sq in 86 sq in 204 sq in 63 sq in 149 sq in sq in sq in sq in sq in sq in sq in sq in sq in 46 sq in 131 sq in 75 sq in 225 sq in 53 sq in 153 sq in 32 sq in 93 sq in 36 sq in 111 sq in 66 sq in 211 sq in 43 sq in 135 sq in 25 sq in 76 sq in 41 sq in 144 sq in 74 sq in 257 sq in 50 sq in 172 sq in 29 sq in 103 sq in 36 sq in 131 sq in 69 sq in 240 sq in 43 sq in 158 sq in 26 sq in 93 sq in 33 sq in 122 sq in 58 sq in 210 sq in 39 sq in 143 sq in 22 sq in 85 sq in 31 sq in 115 sq in 58 sq in 225 sq in 36 sq in 138 sq in 19 sq in 73 sq in 31 sq in 93 sq in 70 sq in 211 sq in 39 sq in 117 sq in 21 sq in 63 sq in 161 sq in 174 sq in 211 sq in 323 sq in 169 sq in 217 sq in 148 sq in 154 sq in INTRODUCTION TO SAFETY CONTENTS SPECIFICATIONS - Level of sound pressure in the driver's cab LpA (accordng to standard prEN 12053 : 1995) 81 dB - Level of sound power in the LwA environment (according to directive 2000/14/EC modified by directive 2005/88/EC) 106 dB - Average weighted acceleration on driver's body m/s2 (according to standard NF EN 13059) - The average weighted acceleration trannsmitted to the driver's hand/arm system (in accordance with ISO 5349-2) is less than 2.5 m/s2 - Speed of movement of lift truck in standard configuration on horizontal ground (except particular conditions) 28,8 km/h (17.9 mph) . Forward unladen 28,8 km/h (17.9 mph) . Reverse unladen - Standard lift height 9610 mm (378.3 in) - Rated capacity with standard attachment 3300 kg (7275.26 lbs) - Load center 24 in - Weight of forks (each) 68 kg (150 lbs) - Lifting motions (boom retracted) . Unladen lifting . Laden lifting . Unladen lowering . Laden lowering 6,7 7,3 5,0 4,7 - Telescoping motions (lifting boom) . Unladen extending . Laden extending . Unladen retracting . Laden retracting s s s s 41,9 38,5 56,2 59,8 m/mn m/mn m/mn m/mn (137.5 (126.3 (184.4 (196.2 13,6 s 14,8 s 8,1 s 7,8 s 25,1 23,1 42,2 43,8 m/mn m/mn m/mn m/mn (82.3 ft/min) (75.8 ft/min) (138.5 ft/min) (143.7 ft/min) - Reverse tilt time unladen 3s 41,9 °/s - Forward tilt time unladen 2,5 s 50,3 °/s - Lift truck weight with standard attachment . Unladen . Rated load 7845 kg (17,295 lbs) 11145 kg (24,571 lbs) - Axle weight with attached equipment (transport position) . Front unladen rated load . Rear unladen rated load 3405 9045 4440 2100 - Tensible strain at coupling hook . Unladen . Rated load 6300 daN (14,162 ft/lbs) 8300 daN (18,658 ft/lbs) kg kg kg kg (7507 lbs) (19,941 lbs) (9789 lbs) (4630 lbs) 6600 daN (14,837 ft/lbs) - Break out force with bucket (according to standard iso 8313) 2-9 ft/min) ft/min) ft/min) ft/min) INTRODUCTION TO SAFETY CONTENTS DIMENSIONS AND LOAD CHART MT 1033 HL Turbo Série 2-E2 A B C C1 D D1 D2 E F F1 G G1 G2 H H1 I J K L N O P2 P3 R S T U1 U2 V V1 V2 W Y Z 2 - 10 1200 mm (47.24 in) 2810 mm (110.63 in) 1393 mm(54.84 in) 1482 mm (58.35 in) 4966 mm (195.51 in) 5055 mm (199.02 in) 4158 mm (163.70 in) 6166 mm (242.76 in) 1846 mm (72.68 in) 1846 mm (72.68 in) 455 mm (17.91 in) 440 mm (17.32 in) 440 mm (17.32 in) 10 ° 10 ° 763 mm (30.04 in) 865 mm (34.06 in) 1040 mm (40.94 in) 45 mm (1.77 in) 1690 mm (66.54 in) 125 mm (4.92 in) 38 ° 53 ° 3610 mm (142.13 in) 7815 mm (307.68 in) 3565 mm (140.35 in) 2300 mm (90.55 in) 2550 mm (100.39 in) 4925 mm (193.90 in) 1360 mm (53.54 in) 3818 mm (150.31 in) 2261 mm (89.02 in) 11,9 ° 113,7 ° INTRODUCTION TO SAFETY CONTENTS 2 - 11 CONTENTS INTRODUCTION TO SAFETY INSTRUMENTS AND CONTROLS 23 3 24 24 5 16 6 19 19 26 20 18 25 7 19 8 19 11 24 1 21 2 11 9 24 17 14 22 10 24 15 28 12 13 29 34 33 2 - 12 27 INTRODUCTION TO SAFETY CONTENTS DESCRIPTION 1 - DRIVER'S SEAT 2 - SAFETY BELT 3 - CONTROL AND SIGNAL LIGHTS PANEL 4 - N/A 5 - SWITCHES PANEL 6 - LIGHT SWITCH, HORN AND INDICATOR SWITCH 7 - IGNITION SWITCH 8 - BRAKING OIL TANK AND WINDSCREEN WASHER ACCESS PANEL 9 - BRAKING OIL TANK 10 - WINDSCREEN WASHER TANK 11 - FUSES AND RELAY ACCESS PANEL 12 - FUSE AND RELAY 13 - ROOF LIGHT 14 - ACCELERATOR PEDAL 15 - SERVICE BRAKE PEDAL AND TRANSMISSION CUT-OFF 16 - FORWARD/REVERSE LEVER 17 - PARKING BRAKE LEVER 18 - STEERING SELECTION 19 - HYDRAULIC CONTROLS 20 - LOAD CHARTS FILE 21 - HEATER CONTROL (OPTIONAL AIR CONDITIONING) 22 - CAB FILTER VENTILATORS 23 - WINDSCREEN DEMIST VENTS 24 - HEATING VENTS 25 - DOOR LOCK 26 - LOCKING HANDLE FOR UPPER HALF DOOR 27 - RELEASING BUTTON FOR UPPER HALF DOOR 28 - HANDLE FOR REAR WINDOW OPENING 29 - TOOL BOX AND DOCUMENT HOLDER 30 - FRONT LIGHTS (NOT ILLUSTRATED) 31 - REAR LIGHTS (NOT ILLUSTRATED) 32 - FLASHING LIGHT (NOT ILLUSTRATED) 33 - SPIRIT LEVEL 34 - TILTING CORRECTOR INDICATOR NOTE : All terms such as : RIGHT, LEFT, FRONT, REAR are as observed by the driver while seated facing forward. 2 - 13 INTRODUCTION TO SAFETY 1 - DRIVER'S CONTENTS SEAT (STANDARD) DESIGNED FOR MAXIMUM COMFORT, THIS SEAT CAN BE ADJUSTED AS FOLLOWS. 1 LONGITUDINAL ADJUSTMENT - Pull locking lever 1 towards the right. - Slide the seat to the required position. - Release the lever and be sure it returns to the lock position. SEAT SUSPENSION ADJUSTMENT - Refer to the seat's graduation. - Turn handle 2 depending on the driver's weight. ADJUSTMENT OF THE ANGLE OF THE BACK-REST - Pull locking lever 3 upwards. - Slide the back-rest to the required position. - Release the lever and be sure it returns to the lock position. 2 1 - DRIVER'S SEAT (OPTION) 3 A DESIGNED FOR MAXIMUM COMFORT, THIS SEAT CAN BE ADJUSTED AS FOLLOWS. WEIGHT ADJUSTMENT (FIG. A) It is advised that the weight be adjusted when the driver is not sitting in the cab. - Refer to graduation 1 of the seat. - Turn handle 2 according to the driver’s weight. NOTE : To avoid any health problems, it is recommended that the weight should be checked and adjusted before starting up the lift truck. SEAT HEIGHT ADJUSTMENT (FIG. B) Raise the seat to the desired position, until you hear the ratchet click. If you raise the seat above the last notch (stop), the seat drops down to the lowest position. SEAT BACK-REST ANGLE ADJUSTMENT (FIG. C) The back-rest angle of the seat may be adjusted to suit the individual. - Press the left-hand button while pushing on the seat or relaxing pressure on the seat to find a comfortable position. B C 2 - 14 INTRODUCTION TO SAFETY CONTENTS SEAT DEPTH ADJUSTMENT (FIG. D) The depth of the seat may be adjusted to suit the individual. - Press the right-hand button while raising or lowering the seat to find the desired position. D EXTENDING THE HEAD-REST (FIG. E) - The height of the back-rest can be adjusted by pulling it upwards (the notches will click) up to the stop. - The head-rest can be removed by applying sufficient pressure to pull it off the stop. LUMBAR ADJUSTMENT (FIG. F) This increases the comfort of the seat and the driver’s freedom of movement. - Turn the handle either left or right to adjust the height or depth of the lumbar support. ADJUSTMENT OF THE ANGLE OF THE BACK-REST (FIG. G) - Support the back-rest, pull the lever and position the back-rest to find the desired position. IMPORTANT E If you do not support the back-rest when making adjustments, it swings completely forwards. LONGITUDINAL ADJUSTMENT (FIG. H) - Adjust the locking lever until you reach the position required. This then locks and the seat will not shift into another position. MAINTENANCE (FIG. I) Dirt may adversely affect the correct functioning of the seat. For this reason, make sure your seat is always clean. - To clean or change the cushions, simply remove them from the seat frame. CAUTION A rocking head-rest increases the risk of an accident! F Avoid wetting the cushion fabric when cleaning. Check the resistance of the fabric on a small hidden area before using any fabric or plastic cleaner. G H 2 - 15 I INTRODUCTION TO SAFETY 1 - PNEUMATIC CONTENTS DRIVER'S SEAT (OPTION) A DESIGNED FOR MAXIMUM COMFORT, THIS SEAT CAN BE ADJUSTED AS FOLLOWS. WEIGHT AND SEAT HEIGHT ADJUSTMENT WEIGHT ADJUSTMENT (FIG. A) It is advised that you adjust the seat according to your weight when sitting. - Switch on lift truck ignition. - Push or pull lever 1 until green appears in display 2 indicating correct adjustment according to your weight. NOTE : To avoid any health problems, it is recommended that the weight should be checked and adjusted before starting up the lift truck. SEAT HEIGHT ADJUSTMENT (FIG. B) When weight adjustment has been carried out, you can then modify seat height. - Keep the ignition switched on. - Push or pull lever 1 until green appears and adjust the height of the seat while checking that the green in display 2 remains visible. IMPORTANT B To avoid causing damage, do not activate the compressor for over 1 minute. SEAT BACK-REST ANGLE ADJUSTMENT (FIG. C) The back-rest angle of the seat may be adjusted to suit the individual. - Press the left-hand button while pushing on the seat or relaxing pressure on the seat to find a comfortable position. SEAT DEPTH ADJUSTMENT (FIG. D) The depth of the seat may be adjusted to suit the individual. - Press the right-hand button while raising or lowering the seat to find the desired position. C EXTENDING THE HEAD-REST (FIG. E) - The height of the back-rest can be adjusted by pulling it upwards (the notches will click) up to the stop. - The head-rest can be removed by applying sufficient pressure to pull it off the stop. LUMBAR ADJUSTMENT (FIG. F) This increases the comfort of the seat and the driver’s freedom of movement. - Turn the handle either left or right to adjust the height or depth of the lumbar support. D E 2 - 16 F INTRODUCTION TO SAFETY CONTENTS ADJUSTMENT OF THE ANGLE OF THE BACK-REST (FIG. G) - Support the back-rest, pull the lever and position the back-rest to find the desired position. IMPORTANT G If you do not support the back-rest when making adjustments, it swings completely forwards. HORIZONTAL SHOCK ABSORBER (FIG. H) In certain conditions (e.g. driving with a trailer) it is advised that a horizontal shock absorber be used. The driver’s seat is thus better able to absorb jerks in the direction of travel. - Position 1 : Horizontal shock absorber fitted. - Position 2 : Horizontal shock absorber removed. LONGITUDINAL ADJUSTMENT (FIG. I) - Adjust the locking lever until you reach the position required. This then locks and the seat will not shift into another position. H MAINTENANCE (FIG. J) Dirt may adversely affect the correct functioning of the seat. For this reason, make sure your seat is always clean. - To clean or change the cushions, simply remove them from the seat frame. CAUTION A rocking head-rest increases the risk of an accident! Avoid wetting the cushion fabric when cleaning. Check the resistance of the fabric on a small hidden area before using any fabric or plastic cleaner. I J 2 - SAFETY - BELT Sit correctly on the seat. Check that seat belt is not twisted. Place the seat belt at hip level. Attach the seat belt and check that it locks. Adjust the seat belt to your body shape without squeezing your hip and without over-slack. WARNING Do not operate the lift truck with a defective seat belt (fixing, locking, cuts, tears, etc.). Repair or replace the seat belt immediately. 2 - 17 INTRODUCTION TO SAFETY 3 - CONTROL CONTENTS AND SIGNAL LIGHTS PANEL B1 B2 B3 B4 C1 CONTROL INSTRUMENTS A - HOURMETER B B - I.C. ENGINE WATER TEMPERATURE Temperature zone B1 - Blue zone (0° - 50°C) 32° - 122°F B2 - Green zone (50° - 100°C) 122° - 212°F B3 - Black/red zone (100° - 105°C) 212° - 221°F B4 - Red zone (105° - 120°C) 221° - 248°F NOTE : Red indicator light “E” comes on between zone B3 and B4. A C C - FUEL LEVEL Red zone C1 indicates that you are using the reserve supply and that time of use is limited. SIGNAL LIGHTS When activating the electrical system of the lift truck, all the red lamps and the panel's buzzer must light to indicate their good working order. If one of the red lamps or the buzzer does not function, carry out the necessary repairs. D H I E J F G K D - NOT USED E - NOT USED L M N O F - RED BRAKING OIL LEVEL LAMP If the lamp and the buzzer come on, when the lift truck is running, stop the I.C. engine immediately and check the braking oil level. In the event of an abnormal loss of fluid, consult your dealer. G - RED PARKING BRAKE LAMP This lamp comes on when the parking brake is applied. H - RED ALTERNATOR CHARGE LAMP If the lamps F - H - I - J - K and the buzzer come on, when the lift truck is running, stop the I.C. engine immediately and check the electrical circuit as well as the alternator belt. I - RED I.C. ENGINE OIL PRESSURE LAMP If the lamp and the buzzer come on when the lift truck is running, stop the I.C. engine immediately and look for the cause (see oil level in I.C. engine crankcase). J - RED I.C. ENGINE WATER TEMPERATURE LAMP If the lamp and the buzzer come on when the lift truck is running, stop the I.C. engine immediately and investigate the cooling system for the cause of the malfunction. K - RED LAMP - AIR FILTER OR HYDRAULIC RETURN FILTER CLOGGED The lamp and buzzer come on when the air filter cartridge or the hydraulic return oil filter cartridge is clogged up. Stop the lift truck and carry out the necessary repairs (see cleaning and replacement requirements in chapter : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). L - GREEN INDICATOR LAMP M - GREEN SIDELIGHTS LAMP N - GREEN LOW BEAM LAMP O - BLUE MAIN BEAM LAMP 4 - N/A 2 - 18 INTRODUCTION TO SAFETY 5 - SWITCHES CONTENTS PANEL A B C D/G E F/G K L M N 2 1 H I J A - WARNING LIGHTS This switch enables the L.H. and R.H. Indicators to be switched on simultaneously, with the ignition off. The signal light indicates that the switch is being used. B - FLASHING LIGHT C - WORKING HEAD LIGHT OPTION D - WORKING TAIL LIGHT OPTION E - REAR FOG LIGHT F - REAR WINDOW DEFROSTING OPTION G - BOOM HEAD LIGHT OPTION H - FRONT WINDSCREEN WIPER AND WINDSCREEN WASHER This two position switch, when set on the "down" position and simultaneously pressed, allows the windscreen-washer and the windscreen wiper to be operated, and when set on the "up" position, the windscreen wiper to be operated. I - GEAR SELECTION Gears can only be selected when the truck is stationary, with the reverse gear in neutral and the brake service pedal and transmission cut-off down. FAST SPEED : Use on the road. Set the switch to low position, fast speed indicator 1 comes on.. SLOW SPEED : Use for handling. Set the switch to high position, slow speed indicator 2 comes on. NOTE : When starting the lift truck, slow speed is automatically selected. J - SPEED LIMITATION The switch is used to limit the lift truck's speed in slow or fast speed, so as to preserve the lift truck's power for fine work. - Set the switch to low position, the indicator which comes on indicates its mode of use. + LIMITED FAST SPEED : Use for fine handling work or earthworks. + LIMITED SLOW SPEED : Use for heavy earthworks. NOTE : The lift truck speed limitation feature only works when the truck is in forward gear. WARNING To prevent the lift truck from slowing down too fast, we recommend that you use the slow speed switch. K - REAR WINDSCREEN WIPER + ROOF WIPER OPTION L - OPTION M - OPTION N - OPTION 2 - 19 INTRODUCTION TO SAFETY 6 - LIGHT CONTENTS SWITCH, HORN AND INDICATOR SWITCH The switch controls the visual and sound alarms. A - All lights are off, the direction indicators do not flash. B - The right hand direction indicators flash. C - The left hand direction indicators flash. D - The sidelights and the rear lights are on. E - The dipped headlights and the rear lights are on. F - The main beam headlights and the rear lights are on. G - Headlight signal. G A C G D B G E F Pressing the switch into the steering column sounds the horn. NOTE : The positions D - E - F - G can be carried out without the ignition being on. 7 - IGNITION SWITCH The key switch has five positions : P - Ignition off, parking position. O - Ignition switched off and I.C. engine stopped. I - Ignition on. II - Heating. III - The I.C. engine starts, return to position i as soon as the key is released. 8 - BRAKING OIL TANK AND WINDSCREEN WASHER ACCESS PANEL - Loosen screw 1 and lift up the brake fluid and windscreen washer access panel. 1 9 - BRAKING OIL TANK See : 3 - MAINTENANCE : B - EVERY 50 HOURS SERVICE. 10 - WINDSCREEN 9 WASHER TANK See : 3 - MAINTENANCE : B - EVERY 50 HOURS SERVICE. 10 11 - FUSE AND RELAY ACCESS PANEL 11 - Lift up the fuse and relay access panel 11. 2 - 20 INTRODUCTION TO SAFETY 12 - FUSE CONTENTS AND RELAY F32 F31 DIST. LSU A sticker on the inside of the access panel displays use of components described below. K1 OPT. OPT. K3 K4 K2 K5 K6 K7 K8 K9 OPT. F1 F2 F3 F4 F5 10A max. F16 OPT. F6 OPT. OPT. F7 F8 F9 F10 STOP F11 F12 F13 F14 OPT. OPT. F15 OPT. OPT. OPT. 25A max. 25A max. 15A 7.5A 10A 7.5A 5A 10A 15A 5A 15A 15A max. 10A 30A F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 7.5A 7.5A 7.5A 7.5A 15A 15A 15A 25A OPT. OPT. 10A max. 15A max. OPT. OPT. 15A 15A max. 10A max. OPT. 10A 15A max. NOTE : Replace a used fuse with a new fuse of the same quality and capacity. Never reuse a repaired fuse. F1 - (10A MAX.) - Security tilting corrector (7,5A). F2 - (15A MAX.) - OPTION Working tail light (10A). F3 - (10A MAX.) - Rear windscreen wiper (7,5A). - OPTION Roof windscreen wiper (7,5A). F4 - (10A MAX.) - Stop I.C. engine electrovalve (7,5A). - OPTION. F5 - (10A MAX.) - Flashing light (7,5A). F6 - (7,5A MAX.) - Alignment of the wheels (5A). F7 - (15A MAX.) - OPTION Hydraulic movements cut-off (10A). F8 - (15A MAX.) - Gear reverser (15A). - Transmission cut-off (15A). - Reverse lights (15A). - Reverse buzzer alarm (15A). F9 - (10A MAX.) - Control instruments panel (5A). F10 - (15A MAX.) - Sound alarm (15A). - Stop switch (15A). F11 - (15A MAX.) - OPTION Boom head light (10A). F12 - (10A MAX.) - Indicator power supply (10A). F13 - (35A MAX.) - Heating (30A). F14 - (25A MAX.) - OPTION. F15 - (25A MAX.) - OPTION. F16 - (10A MAX.) - OPTION Air conditioning (7,5A). F17 - (15A MAX.) - OPTION Electrovalve on boom head (10A). - OPTION Electrovalve on boom head + attachment hydraulic locking device (10A). - OPTION Electrical boom provision (10A). - OPTION Anti-theft device provision (10A). F18 - (15A MAX.) - OPTION Front working head light (15A). F19 - (15A MAX.) - OPTION Rear window defrosting (15A). F20 - (10A MAX.) - OPTION Pneumatic seat (10A). F21 - (10A MAX.) - Front windscreen wiper and windscreen washer (10A). F22 - (15A MAX.) - OPTION. F23 - (10A MAX.) - Right sidelight (7,5A). - Sidelight indicator light (7,5A). - Control panel lighting (7,5A). - OPTION Service plate lighting (7,5A). F24 - (10A MAX.) - Left sidelights (7,5A). F25 - (10A MAX.) - Right indicators (7,5A). F26 - (10A MAX.) - Left indicators (7,5A). F27 - (15A MAX.) - Low beam (15A). - Low beam indicator light (15A). - Rear fog light (15A). F28 - (15A MAX.) - Main beam (15A). - Main beam lamp (15A). 2 - 21 20A OPT. N°243543 K0 - OPTION Air conditioning. K1 - OPTION. K2 - Transmission cut-off relay. K3 - Reverse gear relay. K4 - Forward gear relay. K5 - Buzzer. K6 - OPTION Electrovalve on boom head. - OPTION Electrical boom provision. - OPTION Electrovalve on boom head + attachment hydraulic locking device. K7 - OPTION Hydraulic movements cut-off. K8 - Safety system starting switch relay. K9 - Flashing unit. K11 - Relay for reversing lights + Reverse buzzer alarm. K13 - Slow speed relay. K14 - Fast speed relay. K17 - Relay signal lights panel. 3A K0 K17 K14 K13 K11 INTRODUCTION TO SAFETY CONTENTS F29 - (25A MAX.) - Hazard warning lights power supply (15A). - Roof light (15A). - OPTION (+)permanent (15A). F30 - (25A MAX.) - Light switch power supply, horn and indicators (25A). F31 - (20A MAX.) - Starter (20A). 2 Remove casing 1 and cover 2 for access to fuses F40 to F44 and to relay K21 and K22. F40 - (40A MAX.) - Lift truck electrical equipment (40A). F41 - (40A MAX.) - Lift truck electrical equipment (40A). F42 - (80A MAX.) - Preheating I.C. engine (80A). F43 - (80A MAX.) - Alternator (80A). F44 - (15A MAX.) - OPTION Diesel decongealant (15A). 1 K22 F44 F40 F42 F43 K21 F41 13 - ROOF LIGHT 14 - ACCELERATOR PEDAL 15 - SERVICE BRAKE AND TRANSMISSION CUT-OFF PEDAL The pedal acts on the front wheels by means of a hydraulic brake system enabling the slowing down and stopping of the lift truck. During clearance travel it enables the transmission to be cut off progressively thus allowing a gradual approach (delicate handling) with all the I.C. engine power. 16A - FORWARD/REVERSE LEVER (UP TO S/N: 233950) Bring the lift truck to a complete stop before changing direction of travel. When the lever is in the neutral position a mechanical lock prevents an accidental shifting movement. The driver must be seated before placing the lever in forward or reverse, otherwise a buzzer will sound and the truck will not move. Leaving the seat while the truck is in gear will sound the buzzer and place the truck in neutral. FORWARD : Lift slightly and push the lever forwards (position A). REVERSE : Lift slightly and pull the lever backwards (position B). NEUTRAL : To start the lift truck, the lever must be in the neutral (position C). A C B NOTE : The backup alarm indicates that the lift truck is running in reverse motion. 16B - FORWARD/REVERSE SWITCH (FROM S/N: 233951) Bring the lift truck to a complete stop before changing direction of travel. The driver must be seated before placing the switch in forward or reverse, otherwise a buzzer will sound and the truck will not move. Leaving the seat while the truck is in gear will sound the buzzer and place the truck in neutral. A FORWARD : Push the switch forward (position A). REVERSE : Push the switch back (position B). NEUTRAL : To start the lift truck, the switch must be in the neutral (position C). NOTE : The backup alarm indicates that the lift truck is running in reverse motion. 2 - 22 C B INTRODUCTION TO SAFETY 17 - PARKING CONTENTS BRAKE LEVER To prevent accidental loosening or release, the lever is fitted with safety locking. A - To apply the parking brake, pull the lever backwards (position A). - To loosen the parking brake, release and push the lever forwards (position B). B A3 18 - STEERING SELECTION A Before selecting one of the three possible steering positions, bring the 4 wheels into alignment, i.e., in the straight ahead position. B A - STEERING SELECTION LEVER C A1 A2 B1 A1 - Front wheel steer (highway traffic). B2 A2 - Front and rear wheels steer in opposite direction (4 wheel steer). A3 - Front and rear wheels steer in the same direction (crab steer). B - GREEN LAMPS FOR ALIGNMENT OF THE WHEELS These lamps come on to indicate the alignment of the wheels, in relation to the axle of the lift truck. The lamp B1 for the front wheels and the lamp B2 for the rear wheels. C - SWITCH FOR ALIGNMENT OF THE WHEELS This switch enables the use or not of the device for alignment of the wheels.The indicator light indicates its use. WHEEL ALIGNMENT PROCEDURE - Connect the switch (signal light ON). - Shift the distributor control lever for steering selection A in position A2 (4 wheel steering). - Turn the steering wheel and bring the rear wheels into alignment until the lamp B2 is on. - Shift the distributor control lever for steering selection A in position A1 (highway traffic). - Turn the steering wheel and bring the front wheels into alignment until the lamp B1 is on. WARNING Before driving on public roads, it is necessary to set the alignment of the rear wheels and to drive in front wheel steer. Long distance travel requires periodically stopping the lift truck to check the rear wheel’s alignment (using the green lamps). In case of anomalies, consult your dealer. 2 - 23 INTRODUCTION TO SAFETY CONTENTS 19A - HYDRAULIC CONTROLS (UP TO S/N: 233950) WARNING Do not attempt to alter the hydraulic system pressure by interfering with the pressure regulating valve. In the event of suspected malfunction, contact your dealer. ANY ALTERATION MAY VOID THE WARRANTY. WARNING Use the hydraulic controls carefully without sudden movements, to avoid accidents caused by shaking the lift truck. NOTE : If necessary, slightly turn the steering wheel to reset the hydraulic control/steering accumulator. C LIFTING OF THE LOAD - The lever A backwards when lifting. - The lever A forwards when lowering. TELESCOPING - The lever A to the right extend the boom. - The lever A to the left to retract the boom. NOTE: To retract the boom completely, simply hold the lever to the left, until all telescopes have fully retracted. TILT OF THE CARRIAGE - The lever B forwards to tilt the carriage forward. - The lever B backwards to tilt the carriage backward. FRAME LEVELING - The lever C to the left when tilting the lift truck on the left. - The lever C to the right when tilting the lift truck on the right. NOTE : Tilt can be corrected up to the carriage articulation axle height of 11.5 ft. from the ground, with the boom retracted. ADDITIONAL ATTACHMENT - The lever D forwards or backwards. 19B - HYDRAULIC CONTROLS AND TRANSMISSION CUT-OFF (FROM S/N: 233951) D A B A E LIFTING OF THE LOAD - Move lever A or B backwards to lift. F - Move lever A or B forwards to lower. TILTING THE CARRIAGE - Move the lever B to the left to excavate. B - Move the lever B to the right to tip. TELESCOPING C - Move lever A to the right to extend. - Move lever A to the left to retract. NOTE: When completely retracting the telescopes, keep operating the control until the telescopes are fully retracted. TILTING CORRECTOR D - The lever C to the left when tilting the lift truck on the left. - The lever C to the right when tilting the lift truck on the right. NOTE: Tilt can be corrected up to the carriage articulation axle height of 11.5 ft. from the ground, with the boom retracted. ATTACHMENT - The lever D to the right or left . TRANSMISSION CUT-OFF - Button E allows the transmission to be disconnected for performing handling operations using the full power of the IC engine. REVERSING GEAR - Button F (see: 2 - DESCRIPTION: 16 - REVERSING GEAR). 20 - LOAD CHARTS FILE This file includes the description of the hydraulic controls and the load charts of the attachments used on the lift truck. 2 - 24 INTRODUCTION TO SAFETY CONTENTS 21A - HEATER CONTROL B A A - HEATING FAN CONTROL This 3-speed control regulates warm or cold air through the heating ventilators. B - HEATING TEMPERATURE CONTROL Allows the temperature inside the cab to be adjusted. B1 - With the valve closed, the fan delivers fresh air. B2 - With the valve opened completely, the fan delivers warm air. The intermediate positions allow the temperature to be adjusted. B2 B1 C C - HEATER SHUT OFF VALVE (ENGINE COMPARTMENT) The heater shut off valve must be open to provide heat to the cab. Open the valve fully (rotate counter-clockwise) for maximum heat. 21B - AIR CONDITIONING CONTROLS (OPTIONAL AIR CONDITIONING, ENGINE COMPARTMENT EVAPORATOR) IMPORTANT The air conditioning operates only while the lift truck engine is running. During use, keep the doors and windows closed. In the winter : To ensure correct operation and efficiency of the air conditioning unit, run the compressor once a week, for a few minutes, to lubricate the internal seals. In cold weather : Warm the I.C. engine before switching on the compressor, this will allow the coolant that has collected in the liquid state at the lowest point of the compressor circuit to turn into gas by the heat given off by the I.C. engine (otherwise the compressor is liable to be damaged by pumping coolant in the liquid state when operated). WARNING If your air conditioning does not seem to be working properly, have it examined by your dealer (see : 3 MAINTENANCE : H - EVERY TWO YEARS "OPTION AIR CONDITIONING"). The air conditioning system is under high pressure, repairs must be made by a professional airconditioning repairman. AIR CONDITIONING COMPRESSOR Press the A/C button “A” to activate the compressor, the button light indicates the switch is on (the engine must be running for the compressor to operate). Use the air conditioning for cooling or defrosting the cab. A FOR MAXIMUM COLD: Close the heater shut off valve “B” (rotate clockwise), rotate the temperature control valve “C” to “C1”, and place the fan control “D” to high speed (speed 3). FOR DEFROST: Adjust the fan control “D” to high speed (speed 3), open the heater shut off valve “B” as needed, and rotate the temp control valve “C” to “C2”. NOTE : Possible losses of water under the forklift truck are due to condensate discharges caused by the drying effect of the installation, especially with high outside temperatures and high relative humidity. For the air conditioning to perform properly, the air intakes must not be blocked by frost, snow or leaves. When the unit is running, at least one of the cab air grilles must be open so as to avoid any risk of freezing the evaporator. B C C1 2 - 25 D C2 INTRODUCTION TO SAFETY 21C - AIR CONDITIONING CONTENTS CONTROLS (OPTIONAL AIR CONDITIONING, CAB MOUNTED EVAPORATOR) IMPORTANT The air conditioning operates only while the lift truck engine is running. During use, keep the doors and windows closed. In the winter : To ensure correct operation and efficiency of the air conditioning unit, run the compressor once a week, for a few minutes, to lubricate the internal seals. In cold weather : Warm the I.C. engine before switching on the compressor, this will allow the coolant that has collected in the liquid state at the lowest point of the compressor circuit to turn into gas by the heat given off by the I.C. engine (otherwise the compressor is liable to be damaged by pumping coolant in the liquid state when operated). WARNING If your air conditioning does not seem to be working properly, have it examined by your dealer (see : 3 MAINTENANCE : H - EVERY TWO YEARS "OPTION AIR CONDITIONING"). The air conditioning system is under high pressure, repairs must be made by a professional airconditioning repairman. DESCRIPTION OF THE AIR CONDITIONING CONTROLS A - Control with signal light indicating start-up and cutout of the air conditioning system, if control "D" is in position 1, 2 or 3. B - Heating air temperature control. C - Conditioned air temperature control. D - Air flow setting and fan speed control. In position "0" the air conditioning system no longer functions. C D B A NOTE: Possible losses of water under the forklift truck are due to condensate discharges caused by the drying effect of the installation, especially with high outside temperatures and high relative humidity. For the air conditioning to perform properly, the air intakes must not be blocked by frost, snow or leaves. When the unit is running, at least one of the cab air grilles must be open so as to avoid freezing the evaporator. HEATING MODE The controls must be adjusted in the following way: A - Control with signal light off. B - At the required temperature. C - At the end of travel to the left. D - At the required temperature 1, 2 or 3. C CONDITIONED AIR MODE The controls must be adjusted in the following way: A - Control with signal light on. B - At the end of travel to the left. C - At the required temperature. D - At the required temperature 1, 2 or 3. D B A C DEMISTING (DEFROST) MODE The controls must be adjusted in the following way: A - Control with signal light on. B - At the required temperature. C - At the required temperature. D - At the required temperature 1, 2 or 3. D B A C D B A 2 - 26 INTRODUCTION TO SAFETY CONTENTS 22 - CAB FILTER VENTILATORS See : 3 - MAINTENANCE : D - EVERY 500 HOURS SERVICE. 23 - WINDSCREEN DEMIST VENTS For optimum effectiveness, close the heating ventilators. 24 - HEATING VENTS These heating vents enable the air to be directed to the interior of the cabin and onto the side windows. 25 - DOOR LOCK Two keys are provided with the lift truck to enable the cabin to be locked. 26 - LOCKING HANDLE FOR UPPER HALF DOOR 27 - RELEASING 28 - HANDLE BUTTON FOR UPPER HALF DOOR FOR REAR WINDOW OPENING EMERGENCY EXIT Use the rear window as an emergency exit, if it is impossible to leave the cab by the door. 29 29 - TOOL BOX AND DOCUMENT HOLDER Ensure that the operator's manual is in its place in the document holder. 30 - FRONT LIGHTS A - Left front indicator. B - Left front dipped headlight. C - Left front main beam. D - Left front sidelight. E - Right front indicator. F - Right front dipped headlight. G - Right front main beam. H - Right front sidelight. C G E H D F A B 31 - REAR LIGHTS A - Left rear indicator. B - Left rear stoplight. C - Left tail light. D - Left rear reverse light. E - Left rear fog light. F - Right rear fog light. G - Right rear reverse light. H - Right tail light. I - Right rear stoplight. J - Right rear indicator. A 2 - 27 B C D E F G H I J INTRODUCTION TO SAFETY 32 - REVOLVING CONTENTS LIGHT The revolving light pivots for space-saving on the lift truck and can be detached to prevent theft. - Loosen nut 1 and remove the revolving light. - Protect mounting 2 with cap 3. 1 3 2 33 - SPIRIT LEVEL Enables the operator to check that the lift truck is in the horizontal (level) position. 33 34 - TILTING INDICATOR The indicator informs the user about the tilting given to the lift truck. 34 - The tip of the retracted indicator indicates the tilting towards the left. - The tip of the extended indicator indicates the tilting towards the right. 2 - 28 INTRODUCTION TO SAFETY CONTENTS TOWING PIN AND HOOK Located at the rear of the lift truck, this device is used to attach a trailer. Its capacity is limited for each lift truck by the authorized gross vehicle weight, tractive effort and maximum vertical force on the coupling point. This information is given on the manufacturer's plate attached to each lift truck (see : 2 - DESCRIPTION : IDENTIFICATION OF THE LIFT TRUCK). - To use a trailer, see current regulations in your country (maximum running speed, braking, maximum weight of trailer, etc.). - Verify the trailer's condition before using it (tire condition and pressures, electrical connection, hydraulic hose, braking system…). WARNING Do not tow a trailer or accessory which is not in proper working order. Using a trailer in poor condition may effect the lift truck's steering and braking, and hence safety. WARNING If a third party helps in coupling or uncoupling the trailer, they must be continually visible to the driver until the lift truck is parked and the I.C. engine is turned off. NOTE : There is an OPTIONAL rear-view mirror which allows the lift truck to be maneuvered more closely to the trailer ring. A - TOWING PIN (STANDARD) COUPLING AND UNCOUPLING THE TRAILER - To couple the trailer, position the lift truck as close as possible to the trailer ring. - Engage the parkbrake and turn the I.C. engine off. - Remove the clip 1, lift the trailer pin 2 and place or remove the trailer ring. WARNING 2 Risk of crushed fingers or hands! Keep hands and fingers clear while coupling the trailer! The safety clip 1 must be installed after coupling. Before uncoupling, make sure the trailer is blocked in place and independently supported. 1 B - PROJECTING HOOK (OPTION) COUPLING AND UNCOUPLING THE TRAILER - To couple the trailer, position the lift truck as close as possible to the trailer ring. - Engage the parkbrake and turn the I.C. engine off. - Remove the clip 1, lift the trailer pin 2 and place or remove the trailer ring. WARNING Risk of crushed fingers or hands! Keep hands and fingers clear while coupling the trailer! The safety clip 1 must be installed after coupling. Before uncoupling, make sure the trailer is blocked in place and independently supported. 2 - 29 2 1 INTRODUCTION TO SAFETY C - COUPLING CONTENTS LADDER (OPTION) 4 COUPLING AND UNCOUPLING THE TRAILER - To couple the trailer, position the lift truck as close as possible to the trailer ring. - Engage the parkbrake and turn the I.C. engine off. 6 5 WARNING Risk of crushed fingers or hands! Keep hands and fingers clear while coupling the trailer! The safety clip (and/or rod) must be installed after coupling. Before uncoupling, make sure the trailer is blocked in place and independently supported. 3 1 2 ON THE FIXED PIN - Remove pin 1, remove rod 2 and raise latch 3. - Insert or remove the trailer ring, lower latch 3 and refit rod 2. ON THE COUPLING LADDER - Set the coupling fitting 4 according to the height of the trailer ring. - Remove pin 5, lift the towing pin 6 and insert or remove the trailer ring. D - ELECTRICAL CONNECTION (OPTION) - Connect the male plug to the female socket 1 on the lift truck and make sure the trailer lights work properly. 1 2 - 30 INTRODUCTION TO SAFETY CONTENTS DESCRIPTION AND USE OF ELECTRIC AND HYDRAULIC OPTIONS 1 - REAR ELECTRIC SOCKET 1 Enables power supply connection for a trailer (see : 2 - DESCRIPTION : TOWING PIN AND HOOK) or signalling bar. A - Left rear indicator. C - Earth. D - Right rear indicator. E - Right tail light. F - Rear stoplight. G - Left tail light. A F G E C D 2 - BATTERY CUT-OFF (NOT ILLUSTRATED) 2 3 - SERVICE PLATE 4 - SERVICE PLATE LIGHTING 4 3 4 5 - REAR REFLECTORS 5 2 - 31 5 INTRODUCTION TO SAFETY 6 - PREHEATING CONTENTS ROD (NOT ILLUSTRATED) Enables the motor unit to be kept warm during prolonged periods of parking and thus, ensures the improved start-up of the I.C. engine. Only connect to and disconnect from the power supply while the unit is off and the I.C. engine is stopped. • Rated range of power : 110-120V ; 50-60Hz - The preheating system should not be used for an external ambient temperature higher than 77° F. - It is essential that the power supply to the preheating system is : • Effected with a cable that conforms to the installation standards in force and contains a protective ground conductor. • Incorporates an appropriate safety system against short circuits (fuses or circuit breaker) and a differential circuit breaker with 30mA sensitivity. 7A - ELECTRICAL BOOM PROVISION (UP TO S/N: 233950) 1 Enables an electrical function to be used at the head of the boom. FUNCTIONING - Hold button 1 down and move the lever forwards or backwards. 7B - ELECTRICAL BOOM PROVISION (FROM S/N: 233951) Enables an electrical function to be used at the head of the boom. FUNCTIONING - Hold button 1 down and move the lever forwards or backwards. 1 8 - QUICK-RELEASE COUPLER ON ATTACHMENT CIRCUIT 9 - EXTERIOR DRAIN-BACK (NOT ILLUSTRATED) Enables connection of an attachment for which drain-back is required. 2 - 32 INTRODUCTION TO SAFETY CONTENTS 10 - HYDRAULIC ATTACHMENT LOCKING Enables attachment locking to be controlled on the carriage and the use of a hydraulic attachment on the same hydraulic circuit (see : 4 - ADAPTABLE ATTACHMENTS IN OPTION ON THE RANGE : PICKING UP THE ATTACHMENTS). 11A - BOOM HEAD ELECTROVALVE (UP TO S/N: 233950) Enables use of two hydraulic functions on the attachment circuit. 1 FUNCTIONING - Button 1 not engaged, the lever controls a hydraulic function. - Hold button 1 down, the lever controls another hydraulic function. CAUTION 11B - BOOM HEAD 1 Decompress the hydraulic circuit by pressing button 1 on the electrovalve before attemping to make connections. ELECTROVALVE (FROM S/N: 233951) Enables use of two hydraulic functions on the attachment circuit. 1 FUNCTIONING - Button 1 not engaged, the lever controls a hydraulic function. - Hold button 1 down, the lever controls another hydraulic function. CAUTION Decompress the hydraulic circuit by pressing button 1 on the electrovalve before attemping to make connections. 1 2 - 33 INTRODUCTION TO SAFETY 12 - BOOM CONTENTS HEAD ELECTROVALVE + PREARRANGED HYDRAULIC ATTACHMENT LOCKING The addition of these two options enables the combining of several hydraulic functions. 13 - CLEANFIX SELF-CLEANING FAN This system, operated by switch 1, cleans the radiator core and the grille of the engine cover by reversing the air flow. CAUTION When in use, protect eyes from flying debris. Position A: The indicator light is on, the fan operates in self-cleaning mode for a few seconds once every 3 minutes. Position B: The indicator light is off, the fan is in normal operating mode. B 1 A 2 - 34 INTRODUCTION TO SAFETY CONTENTS 3 - MAINTENANCE 3-1 INTRODUCTION TO SAFETY CONTENTS 3-2 CONTENTS INTRODUCTION TO SAFETY TABLE OF CONTENTS MANITOU FILTERS 3-4 ORIGINAL SPARE PARTS AND EQUIPMENT 3-5 CARTRIDGES AND BELTS LUBRICANTS SERVICING 3-6 AND FUEL 3-8 SCHEDULE A - DAILY OR EVERY 10 B - EVERY 50 3 - 10 HOURS SERVICE 3 - 12 HOURS SERVICE C - EVERY 250 HOURS SERVICE 3 - 18 D - EVERY 500 HOURS SERVICE 3 - 21 E - EVERY 1000 HOURS SERVICE 3 - 25 F - EVERY 2000 HOURS SERVICE 3 - 28 G - OCCASIONAL H - EVERY TWO 3 - 29 MAINTENANCE YEARS (OPTION AIR CONDITIONING) 3 - 32 3-3 CONTENTS INTRODUCTION TO SAFETY MANITOU ORIGINAL SPARE PARTS AND EQUIPMENT TO HONOR YOUR LIFT TRUCK’S FACTORY WARRENTY IT MUST BE SERVICED USING ONLY ORIGINAL MANITOU PARTS. IF YOU USE PARTS WHICH ARE NOT ORIGINAL YOU RISK MANITOU PARTS, - Legally - to be held responsible in the event of an accident. - Technically - to generate operating failure or shorten the life of the lift truck. THE USE OF COUNTERFEIT PARTS OR COMPONENTS NOT APPROVED BY THE MANUFACTURER VOIDS THE BENEFITS OF THE FACTORY WARRENTY GUARANTEE. BY USING ORIGINAL YOU BENEFIT EXPERTISE MANITOU PARTS FOR MAINTENANCE OPERATIONS, THROUGH ITS NETWORK, MANITOU PROVIDES THE USER WITH - Know-how and competence. - The guarantee of high-quality work. - Original replacement components. - Help with preventive maintenance. - Efficient help with diagnosis. - Improvements due to experience feedback. - Operator training. - Only the MANITOU network has detailed knowledge of the design of the lift truck and therefore the best technical ability to provide maintenance. ORIGINAL REPLACEMENT PARTS ARE DISTRIBUTED EXCLUSIVELY BY MANITOU AND ITS DEALER NETWORK. 3-4 INTRODUCTION TO SAFETY CONTENTS FILTERS CARTRIDGES AND BELTS I.C. ENGINE I.C. ENGINE OIL FILTER Part number : 476954 Change : 500 H ALTERNATOR BELT Part number : 605041 DRY AIR FILTER CARTRIDGE Part number : 563416 Clean : 50 H* Change : 500 H* FAN BELT Part number : 229300 SAFETY DRY AIR FILTER CARTRIDGE Part number : 563415 Change : 1000 H* COMPRESSOR BELT (OPTION AIR CONDITIONING) Part number : 244237 FUEL FILTER CARTRIDGE Part number : 605013 Change : 500 H CYCLONIC PRE-FILTER Part number : 224713 Clean : 10 H AUTOMATIC VACUUM-CLEANING PRE-FILTER (OPTION) Part number : 226611 * : Estimate varies (see : 3 - MAINTENANCE : SERVICING SCHEDULE) for cleaning and changing. TRANSMISSION HYDROSTATIC TRANSMISSION OIL FILTER CARTRIDGE (15µ) Part number : 236095 Change : 500 H HYDRAULICS HYDRAULIC RETURN OIL FILTER CARTRIDGE (15µ) Part number : 236095 Change : 500 H SUCTION STRAINER FOR HYDRAULIC OIL TANK Part number : 224726 Clean : 1000 H FILTER CAP FOR HYDRAULIC OIL TANK Part number : 62415 Change : 1000 H CAB CAB VENTILATION FILTER (WITHOUT AIR CONDITIONING) Part number : 225052 Clean : 500 H 3-5 CAB VENTILATION FILTER (WITH AIR CONDITIONING) Part number : 225052 Clean : 50 H Change : 250 H CONTENTS INTRODUCTION TO SAFETY LUBRICANTS AND FUEL USE THE RECOMMENDED LUBRICANTS AND FUEL : DIAGNOSTIC ANALYSIS OF OILS If a service or maintenance contract has been organized with the dealer, a diagnostic analysis of engine, transmission and axle oils may be requested depending on the rate of use. (*) FUEL CHARACTERISTICS Use a high-quality fuel to obtain optimal performance of the I.C. engine. CHARACTERISTICS OF RECOMMENDED FUEL : • Types of diesel N590 - Auto/C0/C1/C2/C3/C4 • BS2869 Class A2 • ASTM D975-91 Class 2-2DA, US DF1, US DF2, US DFA • JIS K2204 (1992) Grades 1, 2, 3 and Special Grade 3. I.C. ENGINE COMPONENT I.C. ENGINE COOLING CIRCUIT FUEL TANK CAPACITY 2 gal RECOMMENDATION Shell: Rotella 15w40 Citgo: C-600 15w40 6.2 gal Tulco 50/50 Anti-freeze 31.7 Diesel fuel Grade 1D TRANSMISSION COMPONENT GEAR BOX CAPACITY 1.7 qts TRANSMISSION UNIVERSAL JOINT RECOMMENDATION Shell: Spirax DH 80w90 Citgo: Prem Gear MP 80w90 Shell: Rentinax Am Citgo: Lithoplex CM-2 JIB COMPONENT RECOMMENDATION Shell: Rentinax Am Citgo: Lithoplex CM-2 Shell: Rentinax Am Citgo: Lithoplex CM-2 BOOM PADS GREASING OF THE JIB HYDRAULICS COMPONENT HYDRAULIC OIL TANK CAPACITY 33 gal RECOMMENDATION Shell: Tellus T46 Citgo: Transgard THF Lo-Temp BRAKE COMPONENT BRAKE CIRCUIT RECOMMENDATION Shell: Donax TG Dexron III Citgo: Transgard ATF Dexron III 3-6 CONTENTS INTRODUCTION TO SAFETY CAB COMPONENT RECOMMENDATION Shell: Rentinax Am Citgo: Lithoplex CM-2 Windscreen washer fluid CAB DOOR WINDSCREEN WASHER TANK FRONT AND REAR AXLES COMPONENT FRONT AXLE DIFFERENTIAL* CAPACITY 1.8 gal REAR AXLE DIFFERENTIAL* 1.9 gal FRONT WHEELS REDUCERS 0.8 qts REAR WHEELS REDUCERS 0.7 qts FRONT AND REAR WHEELS REDUCERS PIVOTS REAR AXLE OSCILLATION FRONT AXLE OSCILLATION RECOMMENDATION PACKAGING Shell: Donax TD 18.9 L (5 gal) Citgo: Transgard Tractor Hyd Fluid Shell: Donax TD 18.9 L (5 gal) Citgo: Transgard Tractor Hyd Fluid Shell: Spirax DH 80w90 Citgo: Prem Gear MP 80w90 Shell: Spirax DH 80w90 Citgo: Prem Gear MP 80w90 Shell: Rentinax Am Citgo: Lithoplex CM-2 Shell: Rentinax Am Citgo: Lithoplex CM-2 Shell: Rentinax Am Citgo: Lithoplex CM-2 CHASSIS COMPONENT TILTING CORRECTOR RECOMMENDATION Shell: Rentinax Am Citgo: Lithoplex CM-2 * First 200 hrs: Use Manitou Special Immersed Brakes 549 Lubricant. (5 gal. drum, p/n: 545608). 3-7 PART NUMBER 545608 545608 INTRODUCTION TO SAFETY CONTENTS SERVICING SCHEDULE A C D G = = = = AJUST CHECK DESCALE GREASE N = CLEAN P = BLEED R = CHANGE V = DRAIN/CHANGE I.C. ENGINE I.C. engine oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling liquid level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cyclonic prefilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dry air filter cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . Radiator core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Condenser core (OPTION Air conditioning) . . . . . . . . . . . . Fan belt tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alternator/crankshaft belt tension . . . . . . . . . . . . . . . . . . Compressor belt tension (OPTION Air conditioning) . . . . . . I.C. engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I.C. engine oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel filter cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety dry air filter cartridge . . . . . . . . . . . . . . . . . . . . . . I.C. engine silent blocks . . . . . . . . . . . . . . . . . . . . . . . . . I.C. engine rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Valves clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water pump and the thermostat . . . . . . . . . . . . . . . . . . . Alternator and the starter motor . . . . . . . . . . . . . . . . . . . TRANSMISSION Gear box oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic transmission oil filter cartridge . . . . . . . . . . . . Gear box oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmission silent blocks . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic transmission circuit pressures . . . . . . . . . . . . Governing start of the hydrostatic transmission . . . . . . . . Working order of the transmission cut-off hydraulic valve . . After Day the first or 50 10 hours hours 250 hours 1 year or 500 hours 1 year or 1000 hours 2000 hours N N N A A R A A A V R R V R R N R C** C** C** C** V N/D** C** C** 3-32 3-21 3-26 3-28 C R V 4000 hours PAGE 3-12 3-12 3-12 3-13 3-14/3-25 3-14 3-14 3-20 3-20 3-21 3-24 3-24 3-25 3-28 3-28 C C C N R V C** C** C** C** TIRES Tires pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel nuts torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Condition of wheels and tires . . . . . . . . . . . . . . . . . . . . . Change a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13 3-13 C C C** 3-34 BOOM Boom pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Boom pads wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Condition of Boom unit . . . . . . . . . . . . . . . . . . . . . . . . . . Bearings and articulation rings . . . . . . . . . . . . . . . . . . . . HYDRAULICS Hydraulic oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic return oil filter cartridge . . . . . . . . . . . . . . . . . . Balancing valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Suction strainer for hydraulic oil tank . . . . . . . . . . . . . . . . Filter cap for hydraulic oil tank . . . . . . . . . . . . . . . . . . . . . Speeds of hydraulic movements . . . . . . . . . . . . . . . . . . . Hydraulic pump pipe filter . . . . . . . . . . . . . . . . . . . . . . . . Condition of hoses and flexibles pipes . . . . . . . . . . . . . . . Condition of cylinders (leakage, shafts) . . . . . . . . . . . . . . Hydraulic circuit pressures . . . . . . . . . . . . . . . . . . . . . . . Hydraulic circuit outputs . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic oil tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 hours 3-13 3-15 G* G C** C** C** 3-16 3-26 3-26 3-29 3-29 3-29 C R C R C V N R C** N** C** C** C** C** N** 3-8 INTRODUCTION TO SAFETY A C D G = = = = AJUST CHECK DESCALE GREASE CONTENTS N = CLEAN P = BLEED R = CHANGE V = DRAIN/CHANGE After Day the first or 50 10 hours hours BRAKE Brake oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake lever mechanism . . . . . . . . . . . . . . . . . . . . Brake oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brake circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brake circuit pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 hours 250 hours 1 year or 500 hours 2000 hours 4000 hours C 3-16 3-21 3-27 A G V** P** C** A** CAB Windscreen washer liquid level . . . . . . . . . . . . . . . . . . . . Cab door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cab ventilation filter (OPTION Air conditioning) . . . . . . . . . Heating block non-return valve . . . . . . . . . . . . . . . . . . . . . Cab ventilation filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Condition of the rear view mirrors . . . . . . . . . . . . . . . . . . Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPTION Air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . C G N 3-17 3-17 3-17/3-22 3-22 3-27 3-30 R N N C C** C** 3-38 ELECTRICITY Battery electrolyte level . . . . . . . . . . . . . . . . . . . . . . . . . . Battery electrolyte density . . . . . . . . . . . . . . . . . . . . . . . . 3-18 3-27 C C Condition of wiring harness and cables . . . . . . . . . . . . . . Lights and signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjust the front headlamps . . . . . . . . . . . . . . . . . . . . . . . FRONT AND REAR AXLES Front wheels reducers pivots . . . . . . . . . . . . . . . . . . . . . . Rear wheels reducers pivots . . . . . . . . . . . . . . . . . . . . . . Rear axle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front axle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmission universal joint . . . . . . . . . . . . . . . . . . . . . . Front axle differential oil level . . . . . . . . . . . . . . . . . . . . . Rear axle differential oil level . . . . . . . . . . . . . . . . . . . . . Front wheels reducers oil level . . . . . . . . . . . . . . . . . . . . . Rear wheels reducers oil level . . . . . . . . . . . . . . . . . . . . . Front axle differential oil . . . . . . . . . . . . . . . . . . . . . . . . . Rear axle differential oil . . . . . . . . . . . . . . . . . . . . . . . . . Front wheels reducers oil . . . . . . . . . . . . . . . . . . . . . . . . Rear wheels reducers oil . . . . . . . . . . . . . . . . . . . . . . . . . Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wearing of front axle brake discs . . . . . . . . . . . . . . . . . . . Front wheels reducers universal joint . . . . . . . . . . . . . . . . Rear wheels reducers universal joint . . . . . . . . . . . . . . . . Steering swivel joints . . . . . . . . . . . . . . . . . . . . . . . . . . . Front wheels reducers clearance . . . . . . . . . . . . . . . . . . . Rear wheels reducers clearance . . . . . . . . . . . . . . . . . . . Bearings clearance of the gear box . . . . . . . . . . . . . . . . . 1 year or 1000 hours C** C** C** 3-36 G G G G G G/C** G/C** G/C** G/C** G/C** C C C C V V V V V V V V 3-18 3-18 3-18 3-18 3-19 3-22 3-22 3-22 3-22 3-27 3-30 3-30 3-30 C** C** C** C** C** C** C** C** CHASSIS Tilting corrector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bearings and articulation rings . . . . . . . . . . . . . . . . . . . . 3-19 G C** C** ATTACHMENTS Forks wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Attachment carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . . Condition of attachments . . . . . . . . . . . . . . . . . . . . . . . . C** C** C** 3-34 3-34 3-35 (*) : Every 10 hours during the first 50 hours, then once at 250 hours. (**) : Consult your dealer. 3-9 INTRODUCTION TO SAFETY CONTENTS A - DAILY OR EVERY 10 HOURS SERVICE A1 - I.C. ENGINE OIL LEVEL A1 CHECK 2 Park the lift truck on level ground with the I.C. engine stopped, allow the oil to settle. - Open the I.C. engine compartment. Remove the dipstick 1 (fig. A1). Wipe the dipstick and check the correct level at the upper mark. If necessary, add oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by the filler port 2 (fig. A1). - Check the engine for oil leaks. A2 - COOLING 1 LIQUID LEVEL A2 CHECK 2 Park the lift truck on level ground with the I.C. engine stopped, and cool. - Open the I.C. engine compartment. Check the correct level in the middle of gauge 1 (fig. A2). If necessary, add cooling liquid (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL). Slowly turn the cap 2 (fig. A2) counterclockwise up to the safety stop. Allow the pressure and vapor to escape. Press down and turn the cap for removal. Add cooling liquid via filler port 3 (fig. A2) up to the middle of gauge 1 (fig. A2). Lubricate the filler neck to ease removal of the radiator cap. Check the system for leaks. WARNING A3 - FUEL 3 1 To avoid risk of boiling water or steam, wait until the I.C. engine has cooled before removing the filler plug. If the cooling fluid is hot, add only hot cooling fluid (176°F). LEVEL CHECK A3 Keep the fuel tank near full, to reduce condensation. - Remove cap 1 (fig. A3). - Fill the fuel tank with clean fuel (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL), filtered through a strainer or a clean, lint free cloth, through filler port 2 (fig. A3). - Put the cap back 1 (fig. A3). - Check the system for leaks. WARNING Never smoke or approach with a flame during filling operations or when the tank is open. Never refill while the I.C. engine is running. WARNING The fuel tank is vented via the filler plug. When changing it, always use an original part, with vented hole. NOTE : A locking tank cap is available as an OPTION. 3 - 10 1 2 INTRODUCTION TO SAFETY CONTENTS A4 - CYCLONIC PREFILTER A4 CLEAN 1 2 The cleaning interval is given as a reference, however the prefilter must be emptied as soon as impurities reach the MAXI level on the tank. - Loosen nut 1 (fig. A4), remove cover 2 (fig. A4) and empty the tank. - Clean the prefilter unit with a clean dry cloth and reassemble the unit. IMPORTANT A5 - TIRE When cleaning, take care not to let impurities into the dry air filter. PRESSURE AND WHEEL NUT TORQUE CHECK - Check the condition of the tires, look for damage; cuts, wear, etc. - Check the torque load of the wheel nuts. Loose wheel nuts can cause damage to the wheel bolts and distort the wheels. Wheel nuts tightening torque • Front tires : 465 ft/lbs • Rear tires : 465 ft/lbs - Check and adjust the tire pressures if necessary (see : 2 - DESCRIPTION : CHARACTERISTICS). WARNING Check that the air hose is correctly connected to the tire valve before inflating and keep all persons at a distance during inflation. Respect the recommended tire pressures given. NOTE : There is an OPTIONAL wheel toolkit. A6 - BOOM PADS A6 CLEAN - GREASE To be carried out every 10 hours during the first 50 hours service, then once at 250 hours. - Extend the boom completely. - With a brush, apply a coat of grease (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) on the 4 sides of the telescope(s) (fig. A6). - Telescope the boom several times in order to spread the coat of grease evenly. - Remove the surplus grease. IMPORTANT If the lift truck is used in an abrasive environment (dust, sand, coal…), use a dry graphite lubricate. Contact your dealer. NOTE : A boom sealing kit is available as an OPTION. 3 - 11 INTRODUCTION TO SAFETY CONTENTS B - EVERY 50 HOURS SERVICE Carry out the operations described previously as well as the following operations. B1 - DRY AIR FILTER CARTRIDGE CHECK - CLEAN In case of use in a heavily dust laden atmosphere, there are pre-filtration cartridges (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). Also, check and clean the cartridge more frequently. IMPORTANT If the clogging indicator light comes on, this operation must be carried out as quickly as possible (1 hour maximum). The cartridge must not be cleaned more than seven times, after which the cartridge must be changed. - For the disassembly and reassembly of the cartridge, see : 3 - MAINTENANCE : D3 - DRY AIR FILTER CARTRIDGE. - Clean the filter cartridge using a compressed air jet (max. 40 psi) directed from the top to the bottom and from the inside towards the outside at a minimum distance of 1.5 in. from the cartridge wall. - Cleaning is completed when there is no more dust on the cartridge. IMPORTANT Avoid tearing or making a hole in the cartridge. The cartridge must not be blown anywhere near the air filter box. Never clean the cartridge by tapping it against a hard surface. Your eyes must be protected during this intervention. - Clean the cartridge seal surfaces with a damp, clean lint-free cloth and grease with a silicone lubricant. - Check the outer condition of the air filter and its mounts. Check the condition of the hoses and their mounts also. IMPORTANT Do not clean the dry air filter cartridge by washing it in liquid. Do not clean the safety cartridge located inside the filter cartridge, change it for a new one if it is dirty or damaged. B3/1 B2 - RADIATOR CORE CLEAN IMPORTANT In a heavy dust atmosphere, clean the radiator core every day. Do not use a water jet or high-pressure steam as this could damage the radiator fins. 1 - Open the I.C. engine compartment. - Clean the radiator with a compressed air jet directed from inside to outside. This is the best way to clean the core of debris. - If necessary, clean the suction grid on the engine compartment. B3 - CONDENSER CORE (OPTION AIR CONDITIONING) CLEAN IMPORTANT In a heavy dust atmosphere, clean the radiator core every day. Do not use a water jet or high-pressure steam as this could damage the radiator fins. - Open the I.C. engine compartment. - Loosen the knurled screw 1 (fig. B3/1) and swing round the filter and condenser unit. - Clean the core with a blast of compressed air aimed from the inside towards the outside (fig. B3/2). This is the best way of removing the impurities. 3 - 12 B3/2 INTRODUCTION TO SAFETY CONTENTS B4 - BOOM B4/1 GREASE To be carried out weekly, if the lift truck has been operated for less than 50 hours during the week. IMPORTANT In the event of prolonged use in an extremely dusty or oxidising atmosphere, reduce this interval to 10 working hours or every day. 1 Clean and lubricate the following points with grease (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) and remove the surplus grease. 1 2 3 4 5 6 7 8 - 1 Lubricators of the boom axle (2 lubricators) (fig. B4/1). Lubricators of the carriage axle (2 lubricators) (fig. B4/2). Lubricator of the tilt cylinder foot axle (1 lubricator) (fig. B4/3). Lubricator of the tilt cylinder head axle (1 lubricator) (fig. B4/4). Lubricator of the lifting cylinder foot axle (1 lubricator) (fig. B4/5). Lubricator of the lifting cylinder head axle (1 lubricator) (fig. B4/6). Lubricator of the compensation cylinder foot axle (1 lubricator) (fig. B4/5). Lubricator of the compensation cylinder head axle (1 lubricator) (fig. B4/7). B4/2 2 B4/3 2 B4/4 B4/5 3 4 5 B4/6 B4/7 8 6 3 - 13 7 INTRODUCTION TO SAFETY B5 - HYDRAULIC OIL CONTENTS B5/1 LEVEL CHECK Park the lift truck on level ground with the I.C. engine stopped, and the boom retracted and lowered as far as possible. - 1 Refer to gauge 1 (fig. B5/1). The oil level is correct when it is at the level of the red point. If necessary, add oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL). Remove cap 2 (fig. B5/2). Add oil by filler port 3 (fig. B5/2). IMPORTANT Use a clean funnel and clean the oil nozzle before filling. - Put the cap back. - Check the system for leaks. B5/2 2 Always maintain the oil level at maximum as cooling depends on the oil flowing through the tank. 3 B6 - BRAKE B6/1 OIL LEVEL CHECK 2 Park the lift truck on level ground. - Loosen screw 1 (fig. B6/1) and remove the access panel for braking oil tank and windscreen washer tank 2 (fig. B6/1). - The level is correct when it is at the MAXI level on the tank. - If necessary, add oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by the filler port 3 (fig. B6/2). - Check the system for leaks. WARNING 1 If the braking oil level is abnormally low, consult your dealer. B6/2 3 3 - 14 INTRODUCTION TO SAFETY B7 - WINDSCREEN CONTENTS B7/1 WASHER LIQUID LEVEL CHECK - Loosen screw 1 (fig. B7/1) and remove the access panel for braking oil tank and windscreen washer tank 2 (fig. B7/1). - Check the level. - If necessary add windscreen washer liquid (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by filler port 3 (fig. B7/2). 2 1 B7/2 3 B8 B8 - CAB DOOR GREASE 1 Clean and lubricate the points 1 (4 lubricators) (fig. B8) with grease (see : 3 MAINTENANCE : LUBRICANTS AND FUEL) and remove the surplus grease. 1 B9 - CAB VENTILATION B9 FILTER (OPTION AIR CONDITIONING) CLEAN - Lift up protective casing 1 (fig. B9). Lift out cabin ventilation filter 2 (fig. B9). Clean the filter with a compressed air jet. Check its condition and change if necessary (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). - Install the filter and protective casing. 3 - 15 1 2 CONTENTS INTRODUCTION TO SAFETY B10 - BATTERY ELECTROLYTE B10/1 LEVEL CHECK 2 Check the electrolyte level in each cell of the battery. If the lift truck is working in a high temperature environment, check the level more frequently. - Open the I.C. engine compartment. Open battery cowl 1 (fig. B10/1) and hold it open with locking device 2 (fig. B10/1). Remove caps 3 (fig. B10/2) from each cell of the battery. The level is correct when it is 1/2 in. above the top of the plates in the battery. If necessary, top up the cells with clean distilled water. Clean and dry caps 3 (fig. B10/2) and install in place firmly. Check the terminal connections, lubricate with petroleum jelly to prevent corrosion. Close the battery cowl. WARNING 1 B10/2 Handling and servicing a battery can be dangerous, take the following precautions : - Wear protective goggles. - Keep the battery horizontal. - Never smoke or work near an open flame. - Work in a well-ventilated area. - In the event of electrolyte being spilled onto the skin or splashed in the eyes, rinse thoroughly with cold water for 15 minutes and call a doctor. B11 - FRONT AND 3 B11 REAR WHEELS REDUCERS PIVOTS GREASE 1 Clean and lubricate the points 1 (8 lubricators) (fig. B11) with grease (see : 3 MAINTENANCE : LUBRICANTS AND FUEL) and remove the surplus grease. B12 - REAR AXLE B12 OSCILLATION GREASE Clean and lubricate the points 1 (2 lubricators) (fig. B12) with grease (see : 3 MAINTENANCE : LUBRICANTS AND FUEL) and remove the surplus grease. 1 B13 - FRONT AXLE 1 B13 OSCILLATION GREASE Clean and lubricate the points 1 (2 lubricators) (fig. B13) with grease (see : 3 MAINTENANCE : LUBRICANTS AND FUEL) and remove the surplus grease. 1 1 3 - 16 CONTENTS INTRODUCTION TO SAFETY B14 - TRANSMISSION B14/1 UNIVERSAL JOINT GREASE Clean and lubricate the following points with grease (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) and remove the surplus grease. 1 1 1 - Lubricators of the universal joint Gear box/Front axle (3 lubricators) (fig. B14/1). 2 - Lubricators of the universal joint Gear box/Rear axle (3 lubricators) (fig. B14/2). 1 B14/2 2 B15 - TILTING 2 2 B15/1 CORRECTOR GREASE Clean and lubricate the following points with grease (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) and remove the surplus grease. 1 1 - Lubricator of the tilting corrector cylinder foot axle (1 lubricator) (fig. B15/1). 2 - Lubricator of the tilting corrector cylinder head axle (1 lubricator) (fig. B15/2). B15/2 2 3 - 17 INTRODUCTION TO SAFETY CONTENTS C - EVERY 250 HOURS SERVICE Carry out the operations described previously as well as the following operations. C1 - FAN BELT TENSION C1/1 CHECK - ADJUST 3 2 - Open the I.C. engine compartment. - Check the belt for signs of wear and cracks, change if necessary (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). - Loosen screw 1 (fig. C1/1) on the tension pulley. - Loosen lock nut 2 (fig. C1/1 and C1/2) and screw 3 (fig. C1/1 and C1/2). - Bring the belt just into contact with pulley 4 (fig. C1/1) (on the lift truck, check this operation by feel). - Make a mark on the head of screw 3 (fig. C1/1 and C1/2) and tighten, turning it 5 times. - Tighten the lock nut 2 (fig. C1/1 and C1/2). - Retighten screw 1 (fig. C1/1) on the tension pulley. IMPORTANT 1 4 When changing the fanbelt, tighten screw 3 (fig. C1/1 and C1/2) by one and a half turns, check the tension again after the first 30 minutes of operation. C1/2 3 2 C2/1 C2 - ALTERNATOR/CRANKSHAFT BELT TENSION CHECK - ADJUST - Open the I.C. engine compartment. Unscrew the fastening screws 1 (fig. C2/1). Lay down the protective guard 2 (fig. C2/1). Check the belt for signs of wear and cracks, change if necessary (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). Check the belt tension between the pulleys of the crankshaft and of the alternator. Under a normal pressure exerted with the thumb, the tension should be approximately 3/8 in.. Carry out adjustments if necessary. Loosen screws 3 (fig. C2/2) by two to three thread turns. Swivel the alternator assembly so as to obtain the belt tension required. Retighten screws 3 (fig. C2/2). Put the protective guard back 2 (fig. C2/1). IMPORTANT 1 2 1 1 C2/2 If the alternator belt has to be changed, check the tension again after the first 20 hours of operation. 3 3 3 - 18 INTRODUCTION TO SAFETY CONTENTS C3 - COMPRESSOR BELT TENSION (OPTION AIR CONDITIONING) C3/1 CHECK - ADJUST - Open the I.C. engine compartment. Unscrew the fastening screws 1 (fig. C3/1). Lay down the protective guard 2 (fig. C3/1). Check the belt for signs of wear and cracks and change if necessary (see : 3 MAINTENANCE : FILTERS CARTRIDGES AND BELTS). Check the belt tension between the pulleys of the crankshaft and of the compressor. Under a normal pressure exerted with the thumb, the tension should be approximately 3/8 in.. Carry out adjustments if necessary. Loosen screws 3 (fig. C3/2) by two to three thread turns. Swivel the compressor assembly so as to obtain the belt tension required. Retighten screws 3 (fig. C3/2). Put the protective guard back 2 (fig. C3/1). IMPORTANT 2 1 1 1 C3/2 If the compressor belt has to be changed, check the tension again after the first 20 hours of operation. 1 1 C4 - GEAR BOX OIL C4 LEVEL CHECK Park the lift truck on level ground with the I.C. engine stopped. - Remove level plug 1 (fig. C4). The oil should be flush with the edge of the hole. - If necessary, add oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by the same hole. - Replace and tighten the level plug 1 (fig. C4). C5 - PARKING 1 C5/1 BRAKE 4 CHECK - ADJUST Park the lift truck on a slope less than 15 % with the rated load in the transport position. - Check the tightening adjustment by locking the parking brake in position A (fig. C5/1). - The adjustment is correct when the lift truck is held stationary on a slope. - Carry out adjustments if necessary. A B ADJUSTMENT OF THE PARKING BRAKE CABLE ON THE FRONT AXLE - Press and release the brake pedal, then release the parking brake, putting it in position B (fig. C5/1). - Unscrew nuts 1 (fig. C5/2). - Adjust the cable by untightening nuts 1 (fig. C5/2), until a clearance of 0.06 in. between cams 2 (fig. C5/3) and stops 3 (fig. C5/3) is obtained. C5/2 WARNING The adjustment of the stops performed by the manufacturer must not be modified under any circumstances! ADJUSTMENT OF THE PARKING BRAKE - Leave the parking brake in position B (fig. C5/1). - Progressively tighten the end piece of the lever 4 (fig. C5/1) and recheck braking. - Repeat the operation until the correct braking adjustment is obtained. 3 - 19 1 1 INTRODUCTION TO SAFETY CONTENTS C5/3 3 2 C6 - CAB VENTILATION 3 2 FILTER (OPTION AIR CONDITIONING) C6 CHANGE 1 - Lift up protective casing 1 (fig. C6). - Lift out cabin ventilation filter 2 (fig. C6) and fit new replacement filter (see : 3 MAINTENANCE : FILTERS CARTRIDGES AND BELTS). - Install the protective casing. 2 C7 - HEATING BLOCK NON-RETURN VALVE C7 CLEAN - Since non-return valve 1 (fig. C7) is located under the cab, it is possible for it to become obstructed with spattered mud. Clean if necessary. C8 - FRONT AND 1 REAR AXLE DIFFERENTIAL OIL LEVEL C8 CHECK 2 Park the lift truck on level ground with the I.C. engine stopped. 1 - Remove level plug 1 (fig. C8). The oil should be flush with the edge of the hole. - If necessary, add oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by the filler port 2 (fig. C8). - Replace and tighten the level plug 1 (fig. C8) (tightening torque 30 ft/lbs). - Repeat this operation for the rear axle differential. C9 - FRONT AND REAR WHEELS REDUCERS OIL LEVEL C9 CHECK Park the lift truck on level ground with the I.C. engine stopped. - Check the level on each wheel reducer. Place level plug 1 (fig. C9) in the horizontal position. Remove the level plug ; the oil should be flush with the edge of the hole. If necessary, add oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by the same hole. Replace and tighten the level plug 1 (fig. C9) (tightening torque 30 ft/lbs). 3 - 20 1 INTRODUCTION TO SAFETY CONTENTS D - EVERY 500 HOURS SERVICE Carry out the operations described previously as well as the following operations. D1 - I.C. ENGINE OIL D1/1 DRAIN D2 - I.C. ENGINE OIL FILTER 1 CHANGE Park the lift truck on level ground, let the I.C. engine run at idle for a few minutes, then stop the I.C. engine. DRAINING THE OIL - Open the I.C. engine compartment. - Remove access panel 1 (fig. D1/1). - Place a container under drain plug 2 (fig. D1/2) and unscrew the plug 3 (fig. D1/3). - Take drain hose 4 (fig. D1/4). - Place the end of the drain hose in the container and attach the union to the drain port 5 (fig. D1/5). - Remove filler cap 6 (fig. D1/6) in order to ensure that the oil is drained properly. IMPORTANT D1/2 Dispose of the drain oil in an ecological manner. REPLACEMENT OF THE FILTER - Remove I.C. engine oil filter 7 (fig. D1/3) ; discard the filter and the filter seal. - Clean the filter bracket with a clean, lint-free cloth. - Fill the new oil filter (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS) with I.C. engine oil and lightly grease the seal. - Install the oil filter on the filter bracket. IMPORTANT 2 Tighten the oil filter by hand pressure only and lock the filter in place by a quarter turn. D1/3 FILLING UP THE OIL - Loosen, clean and put back in place the drain hose 4 (fig. D1/4). - Install and tighten drain plug 3 (fig. D1/3). - Install access panel 1 (fig. D1/1). - Fill up with oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by filler port 8 (fig. D1/6). - Wait a few minutes to allow the oil to flow into the sump. - Start the I.C. engine and let it run for a few minutes. - Check for leaks at the drain plug and oil filter. - Stop the I.C. engine, wait a few minutes and check the level at the upper mark on dipstick 9 (fig. D1/6). - Top up the level if necessary. 7 3 D1/4 4 D1/5 D1/6 6 5 8 9 3 - 21 INTRODUCTION TO SAFETY CONTENTS D3 - DRY AIR FILTER CARTRIDGE D3 CHANGE 1 For heavily dust laden environments, there are pre-filtration cartridges, see : 3 MAINTENANCE : FILTERS CARTRIDGES AND BELTS. Also, check and clean the cartridge more frequently. IMPORTANT - - Change the cartridge in a clean location, with the I.C. engine stopped. Never run the I.C. engine with the air filter removed or damaged. 2 Open the I.C. engine compartment. Loosen the bolts and remove cover 1 (fig. D3). Gently remove the cartridge 2 (fig. D3), taking care to avoid spilling the dust. Leave the safety cartridge in place. The following parts must be cleaned with a damp, clean lint-free cloth. • The inside of the filter housing and cover. • The inside of the filter inlet hose. • The gasket surfaces in the filter and in the cover. Check hoses, connections and state of the clogging indicator on the filter. Before installing check the condition of the new cartridge (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). Introduce the cartridge into the filter housing and push it in, pressing the edges and not the middle. Reassemble the cover, guiding the valve downwards. D4 - FUEL FILTER CARTRIDGE D4/1 CHANGE IMPORTANT Make sure the electrical contact on the lift truck is off, otherwise fuel will be released if the lift pump is on. - Open the I.C. engine compartment. - Carefully clean the outside of the filter and housing, to prevent dust from getting into the system. - Place a container under the filter and drain it via drain plug 1 (fig. D4/1). - Loosen the body of filter 2 (fig. D4/1). - Remove the filter cartridge by pressing the cartridge 3 (fig. D4/2) down against the pressure of the spring and turn it to the left to extract it. - Insert a new cartridge (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS), by pressing the cartridge 3 (fig. D4/2) down against the pressure of the spring and turn it to the right to lock it into the body of the filter. - Place the new seal 4 (fig. D4/2) onto the body of the filter and lubricate the contact surface using clean engine oil. - Insert the body into its housing, hand-tighten only and lock with a quarter-turn. - Close drain plug 1 (fig. D4/1) and remove the container. - Before starting the I.C. engine, turn the ignition on for one minute, give the lift pump time to pump air from the filter. - Start up the I.C. engine and check for leaks. 3 - 22 2 1 D4/2 4 3 INTRODUCTION TO SAFETY CONTENTS D5 - HYDROSTATIC TRANSMISSION D5 OIL FILTER CARTRIDGE CHANGE Park the lift truck, stop the I.C. engine and place the forward/reverse lever in neutral. IMPORTANT Thoroughly clean the outside of the filter and its surroundings before any intervention, to prevent risk of polluting the hydrostatic circuit. - Place a container under hydrostatic transmission oil filter 1 (fig. D5). - Unscrew the body of the filter. - Remove the hydrostatic transmission oil filter cartridge and fit new replacement cartridge (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). - Make sure that the cartridge is correctly positioned, install the body of the filter. IMPORTANT 1 Tighten the body of the filter by hand pressure only and lock the body of the filter in place by a quarter turn. D6 - HYDRAULIC RETURN D6 OIL FILTER CARTRIDGE CHANGE Park the lift truck, stop the I.C. engine and remove the pressure from the circuits by acting on the hydraulic controls. IMPORTANT Thoroughly clean the outside of the filter and its surroundings before any intervention, to prevent risk of polluting the hydraulic circuit. 1 - Place a container under hydraulic drain filter 1 (fig. D6). - Unscrew the body of the filter. - Remove the hydraulic return oil filter cartridge and fit new replacement cartridge (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). - Make sure that the cartridge is correctly positioned and install the body of the filter. IMPORTANT D7 - BALANCING Tighten the body of the filter by hand pressure only and lock the body of the filter in place by a quarter turn. VALVE CHECK To be performed after the first 50 hours of operation and then every 500 hours. Park the lift truck on horizontal (level) ground, put the handbrake on and set the forward/reverse lever to neutral. ROLE OF BALANCING VALVES - The balancing valves protect the user from any risk due to a fall in hydraulic pressure or an exploding hose during hydraulic operations. DANGER Keep everyone well away during these inspections. In all cases, the balancing valve(s) concerned must be repaired or replaced if hydraulic movement continues after the I.C. engine has been switched off. Never use the lift truck with a defective balancing valve. TESTING EACH HYDRAULIC MOVEMENT LIFTING CIRCUIT : - Start up the lift truck and raise the boom by about 45°. - With the I.C. engine running at mid- speed, lower the boom. While the boom is being lowered, switch off the I.C. engine; movement should slow down as the I.C. engine speed falls and stop when the I.C. engine stops. TELESCOPING CIRCUIT : - Start up the lift truck and raise the boom as far as it will go, extending the telescope(s) completely. - With the I.C. engine running at mid- speed, retract the telescope(s). When retracting the boom, switch off the I.C. engine; movement should slow down as the I.C. engine speed falls and stop when the I.C. engine stops. TILT CIRCUIT : - Place the nominal load on the forks, anchor it correctly to prevent it from falling off during the test. - Start up the lift truck and tilt the carriage backwards, lifting the boom sufficiently to allow the carriage to tilt. - With the I.C. engine running at mid-speed, tilt the carriage forwards. While it is tilting, switch off the I.C. engine; movement should slow down as the I.C. engine speed falls and stop when the I.C. engine stops. TILT CORRECTOR CIRCUIT : - Start up the lift truck and tilt (rotate) it completely towards the right or left. - With the engine running at mid-speed, restore it to a level position. While performing this operation, switch off the engine; movement should slow down as the engine speed falls and stop when the engine stops. 3 - 23 CONTENTS INTRODUCTION TO SAFETY D8 - PARKING D8 BRAKE LEVER MECHANISM GREASE - Clean and grease articulation axles 1 (fig. D8) with grease (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL). 1 1 1 D9 - CAB VENTILATION FILTER D9 CLEAN 1 - Lift up protective casing 1 (fig. D9). Lift out cabin ventilation filter 2 (fig. D9). Clean the filter with a compressed air jet. Check its condition and change if necessary (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). - Install the filter and protective casing. D10 - BATTERY ELECTROLYTE 2 DENSITY CHECK D10 1.240 1.250 The electrolyte density varies depending on the temperature, but a minimum of 1260 at 61°F must be maintained. In the shaded area (fig. D10), the battery is in a normal charge condition. Readings above this zone indicate that the battery needs to be recharged. The density should not vary more than 0.025 units between cells. 1.260 1.270 1.280 1.290 - Check the electrolyte density in each battery cell using a hydrometer. - After topping up with distilled water, recharge the battery for at least an hour before checking the battery electrolyte density. WARNING 1.300 Handling and servicing a battery can be dangerous, take the following precautions : - Wear protective goggles. - Keep the battery horizontal. - Never smoke or work near an open flame. - Work in a well-ventilated area. - In the event of electrolyte being spilled onto the skin or splashed in the eyes, rinse thoroughly with cold water for 15 minutes and call a doctor. D11 - FRONT AXLE °C -18 -10 0 10 20 30 40 °F 0 14 32 50 68 86 104 DIFFERENTIAL OIL D11 DRAIN 3 Park the lift truck on level ground with the engine stopped and the differential oil still warm. IMPORTANT 2 Dispose of the drain oil in an ecological manner. - Place a container under drain plugs 1 (fig. D11) and unscrew the plugs. - Remove level plug 2 (fig. D11) and filler plug 3 (fig. D11) in order to ensure that the oil is drained properly. - Install and tighten drain plugs 1 (fig. D11) (tightening torque 30 ft/lbs). - Fill up with oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by filler port 3 (fig. D11). - The level is correct when the oil level is flush with the edge of port 2 (fig. D11). - Check for leaks at the drain plugs. - Install and tighten level plug 2 (fig. D11) and filler plug 3 (fig. D11) (tightening torque 30 ft/lbs). 3 - 24 1 1 1 INTRODUCTION TO SAFETY CONTENTS E - EVERY 1000 HOURS SERVICE Carry out the operations described previously as well as the following operations. E1 - FUEL TANK E1/1 CLEAN WARNING While carrying out these operations, do not smoke or work near a flame. Park the lift truck on level ground with the I.C. engine stopped. - Check the system for leaks. - In the event of a leak, contact your dealer. WARNING - 1 Never perform welding on the fuel system, this could cause an explosion or a fire. Place a container under drain plug 1 (fig. E1/1) and unscrew the plug. Remove cap 2 (fig. E1/2). Let the fuel drain, then flush with 2 gal. of clean fuel by filler port 3 (fig. E1/2). Install and tighten drain plug 1 (fig. E1/1) (tightening torque 26 ft/lbs). Fill the fuel tank with clean fuel (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) filtered through a strainer or a clean, lint-free cloth and install the filler plug 2 (fig. E1/2). E1/2 2 3 E2 E2 - SAFETY DRY AIR FILTER CARTRIDGE CHANGE - For the disassembly and reassembly of the cartridge, see : 3 - MAINTENANCE : D3 - DRY AIR FILTER CARTRIDGE. - Gently remove the dry air filter safety cartridge 1 (fig. E2), taking care to avoid spilling the dust. - Clean the gasket surface on the filter with a damp, clean lint-free cloth. - Before installing check the condition of the new safety cartridge (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). - Insert the cartridge into the filter housing and push it in place, pressing the edges and not the middle. 1 NOTE : The period for changing the safety cartridge is given for reference only. The safety cartridge must be changed for every two changes of the air filter cartridge. E3 E3 - GEAR BOX OIL DRAIN Park the lift truck on level ground with the engine stopped, the gear box oil still warm. 2 - Place a container under drain plug 1 (fig. E3) and unscrew the plug. - Remove level and filler plug 2 (fig. E3) to ensure the oil is drained properly. IMPORTANT Dispose of the drain oil in an ecological manner. 1 - Install and tighten drain plug 1 (fig. E3). Fill up with oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by filler port 2 (fig. E3). The level is correct when the oil level is flush with the edge of port 2 (fig. E3). Check for any possible leaks at the drain plug. Install and tighten level and filler plug 2 (fig. E3). 3 - 25 INTRODUCTION TO SAFETY CONTENTS E4 - HYDRAULIC OIL E4/1 DRAIN E5 - SUCTION STRAINER FOR HYDRAULIC OIL TANK CLEAN E6 - FILTER CAP FOR HYDRAULIC OIL TANK CHANGE Park the lift truck on level ground with the I.C. engine stopped, boom retracted and lowered as far as possible. IMPORTANT 1 1 Before any intervention, thoroughly clean the area surrounding the drain plugs and the suction cover on the hydraulic tank. DRAINING THE OIL - Place a container under drain plug 1 (fig. E4/1) and unscrew the plug. - Remove filler cap 2 (fig. E4/2) to ensure that the oil is drained properly. E4/2 2 IMPORTANT Dispose of the drain oil in an ecological manner. 4 CLEANING THE STRAINER - Remove suction cover 3 (fig. E4/3). - Remove and clean the strainer using a compressed air jet, check its condition and replace if necessary (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). - Install the strainer and tighten the suction cover 3 (fig. E4/3) (tightening torque 60 ft/lbs) making sure the seal is in the correct position. FILLING UP THE OIL - Clean and install drain plug 1 (fig. E4/1) (tightening torque 25 ft/lbs). - Fill up with oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by filler port 4 (fig. E4/2). IMPORTANT Use a clean container and funnel, and clean the underside of the oil nozzle before filling. E4/3 3 - Observe the oil level on dipstick 5 (fig. E4/4) ; the oil level should be at the level of the red point. - Check for leaks at the drain plug. - Replace filler plug 2 (fig. E4/2) with a new filler plug (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS). POLLUTION ABATEMENT OF THE HYDRAULIC CIRCUIT - Let the I.C. engine run at half throttle for 5 minutes without using hydraulic components, then for 5 more minutes while using the hydraulic components (except the steering system). - Accelerate the I.C. engine at full speed for 1 minute, then activate the steering system. - This operation flushes the hydraulic system oil through the hydraulic return oil filter. E4/4 5 3 - 26 INTRODUCTION TO SAFETY CONTENTS E7 - SEAT BELT CHECK SEAT BELT WITH TWO ANCHORING POINTS - Check the following points : • Fixing of the anchoring points on the seat. • Cleanness of the strap and the locking mechanism. • Triggering of the locking mechanism. • Condition of the strap (cuts, curled edges). REELED SEAT BELT WITH TWO ANCHORING POINTS - Check the points listed above together with the following points : • The correct winding of the belt. • Condition of the reel guards. • Roller locking mechanism when the strap is given a sharp tug. NOTE : After an accident, replace the seat belt. WARNING E8 - REAR AXLE Under no circumstances should you use the lift truck if the seat belt is damaged! Repair or replace the seat belt immediately! E8 DIFFERENTIAL OIL DRAIN 3 Park the lift truck on level ground with the I.C. engine stopped and the differential oil still warm. IMPORTANT 2 Dispose of the drain oil in an ecological manner. 1 - Place a container under drain plugs 1 (fig. E8) and unscrew the plugs. - Remove level plug 2 (fig. E8) and filler plug 3 (fig. E8) to ensure that the oil is drained 1 1 properly. - Install and tighten drain plugs 1 (fig. E8) (tightening torque 31 ft/lbs). - Fill up with oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by filler port 3 (fig. E8). - The level is correct when the oil level is flush with the edge of port 2 (fig. E8). - Check for leaks. - Install and tighten level plug 2 (fig. E8) (tightening torque 31 ft/lbs) and filler plug 3 (fig. E8) (tightening torque 31 ft/lbs). E9 - FRONT AND E9 REAR WHEELS REDUCERS OIL DRAIN Park the lift truck on level ground with the I.C. engine stopped and the reducers oil still warm. IMPORTANT - 1 B Dispose of the drain oil in an ecological manner. Drain and change each wheel reducer. Place drain plug 1 (fig. E9) in position A. Place a container under the drain plug and unscrew the plug. Let the oil drain fully. Place the drain port in position B, i.e. in a level port. Fill up with oil (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) by level port 1 (fig. E9). The level is correct when the oil level is flush with the edge of the hole. Install and tighten the drain plug 1 (fig. E9) (tightening torque 31 ft/lbs). 3 - 27 A INTRODUCTION TO SAFETY CONTENTS F - EVERY 2000 HOURS SERVICE Carry out the operations described previously as well as the following operations. F1 - COOLING LIQUID F1/1 DRAIN These operations are to be carried out when necessary or every two years at the beginning of winter. Park the lift truck on level ground with the I.C. engine stopped and cold. DRAINING THE LIQUID - Open the I.C. engine compartment. - Remove the shroud 1 (fig. F1/1). - Set a container under drain valve 2 (fig. F1/2) on the radiator and drain plug 3 (fig. F1/3) of the engine block and loosen them. - Remove filler cap 4 (fig. F1/4) of the radiator. - Let the cooling circuit drain, ensure the ports do not get clogged. - Check the condition of the hoses and fasteners, change the hoses if necessary. - Rinse the circuit with clean water, use approved flushing agent if necessary. 1 F1/2 FILLING THE LIQUID - Tighten the drain valve 2 (fig. F1/2) and drain plug 3 (fig. F1/3) (tightening torque 30 ft/lbs). - Slowly fill the circuit with cooling liquid (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL) to the middle of gauge 5 (fig. F1/4) through filler port 6 (fig. F1/4). - Install filler cap 4 (fig. F1/4). - Run the I.C. engine at idle for a few minutes. - Check for leaks. - Install the shroud 1 (fig. F1/1) - Check the level and refill if necessary. IMPORTANT 2 To pervent corrosion the I.C. engine cooling system must be filled with a minimum mixture of 25 % ethylene glycol-based antifreeze. F1/3 3 F1/4 4 6 5 3 - 28 INTRODUCTION TO SAFETY CONTENTS G - OCCASIONAL MAINTENANCE G1 - WHEEL G1/1 CHANGE - Park the lift truck on even, hard ground. - Put the warning lights on. - Immobilize the lift truck in both directions on the wheel opposite to the one to be changed. - Loosen the nuts of the wheel to be changed. - Place the jack under the flared axle tube, as near as possible to the wheel and adjust the jack (fig. G1/1). - Lift the wheel until it comes off the ground and place the safety support under the axle (fig. G1/2). - Completely unscrew the wheel nuts and remove them. - Free the wheel and roll it to the side. - Slip the new wheel on the wheel hub. - Install the nuts by hand, if necessary grease them. - Remove the safety support and lower the lift truck with the jack. - Tighten the wheel nuts with a torque wrench (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE for tightening torque). G1/2 G2 - LIFT TRUCK G2 TOW IMPORTANT The lift truck must be towed at very slow speed (less than 3 mph) over the shortest possible distance (less than 325 ft). 2 - Park the lift truck, set the forward/reverse gear to neutral. - Set the reduction gearbox to neutral, as follows. - Place a tray under the hoses 1 (fig. G2), loosen them and block the holes. WARNING 1 1 Release the pressure and wait until the oil has stopped flowing before unscrewing the hose ends completely. Use a tool to slide pin 2 (fig. G2) and note the three positions. Make sure the pin is well slotted into the intermediate position, i.e. in neutral. - Release the handbrake. - Switch on the warning lights. - If the I.C. engine is not running there will be no steering or braking assistance. Operate the steering and brake pedal slowly, avoid sudden movements. - After towing, reconnect the hoses. G3/1 G3 - LIFT TRUCK SLING - Take into account the position of the lift truck gravity center for lifting (fig. G3/1). A = 1590 mm B = 1220 mm - Place the hooks in the fastening points provided (fig. G3/2 and G3/3). A 3 - 29 B INTRODUCTION TO SAFETY CONTENTS G3/2 G4 - LIFT TRUCK G3/3 G4/1 ON A PLATFORM TRANSPORT WARNING Ensure that the safety instructions for the platform are followed before loading the lift truck and that the driver of transport is informed about the dimensions and weight of the lift truck. WARNING Ensure that the platform has dimensions and load capacity sufficient for transporting the lift truck. IMPORTANT For lift trucks equipped with a turbo-charged I.C. engine, block off the exhaust outlet to avoid rotation of the turbo shaft without lubrication when transporting the vehicle. G4/2 LOAD THE LIFT TRUCK - Block the wheels of the platform. - Fix the loading ramps so that you obtain an angle as little as possible to lift the lift truck. - Load the lift truck parallel to the platform. - Park the lift truck (see : 1 - OPERATING AND SAFETY INSTRUCTIONS : DRIVING INSTRUCTIONS UNLADEN AND LADEN). STOW THE LIFT TRUCK - Fix the chocks to the platform at the front and back of each tire (fig. G4/1). - Fix also chocks to the inside of each tire (fig. G4/2). - Attach the lift truck to the platform with approved strap or chain. At the front of the lift truck, on the fastening points 1 (fig. G4/3) and at the back, on the towing pin 2 (fig. G4/4). - Tighten the strapes (fig. G4/5). G4/3 1 G4/4 G4/5 2 3 - 30 1 INTRODUCTION TO SAFETY CONTENTS G5 - FRONT HEADLAMPS G5 ADJUST h2 = h1 - (l x 2 / 100) RECOMMENDED SETTING (as per standard ECE-76/756 76/761 ECE20) Set to - 2% of the dipped beam in relation to the horizontal line of the headlamp. h1 +% -% -2% ADJUSTING PROCEDURE - Park the lift truck unloaded, in the transport position and perpendicular to a white wall on flat, level ground (fig. G5). - Check the tire pressures (see : 2 - DESCRIPTION : CHARACTERISTICS). h1 h2 l CALCULATING THE HEIGHT OF THE DIPPED BEAM (H2) • h1 = Height of the dipped beam in relation to the ground. • h2 = Height of the adjusted beam. •l = Distance between the dipped beam and the white wall. G7 - FUEL SYSTEM BLEEDING G1/1 BLEED 1 These operations are to be carried out only in the following cases: • A component of the fuel system replaced. • A drained tank. • Running out of fuel. Ensure that the level of fuel in the tank is sufficient and bled in the following order: - Open the I.C. engine compartment. - Turn the ignition switch on for three minutes, to give the lift pump time to pump air from the fuel filter. - Turn the ignition off. G1/2 BLEEDING THE INJECTORS - Remove the injectors cover 1 (fig. G1/1). - Loosen high pressure connectors 2 (fig. G1/2) of all the injectors. - Activate the starter until the diesel fuel flows out free of air at high pressure connectors 2 (fig. G1/2). IMPORTANT Do not engage the starter motor on a continual basis for more than 30 seconds and let it cool between unsuccessful attempts. 2 2 2 2 - Tighten the connection while the diesel fuel is flowing out (tightening torque 22 ft.lbs.). - The I.C. engine is then ready to be started up. - Idle the engine slowly for 5 minutes immediately after bleeding the fuel feed circuit, to ensure that the injection pump has been bled thoroughly. NOTE: If the engine functions correctly for a short time then stops or functions irregularly, check for possible leaks in the low pressure circuit. If in doubt, contact your dealer. 3 - 31 INTRODUCTION TO SAFETY CONTENTS H - EVERY TWO YEARS (OPTION AIR CONDITIONING) WARNING WARNING DO NOT ATTEMPT REPAIRS. ONLY A QUALIFIED AIR CONDITIONING SERVICEMAN SHOULD MAKE REPAIRS. CONTACT YOUR DEALER. Do not open the cooling circuit under any circumstances, this will cause the coolant to be lost. The cooling circuit contains a gas which can be dangerous under certain conditions. This gas, coolant R 134a, is colorless, odorless and heavier than air. If the gas is inhaled, take the victim into fresh air, give oxygen or artificial respiration if necessary and call a doctor.• If the gas is in contact with the skin, wash it immediately under running water and remove any contaminated garments.• If the gas is in contact with the eyes, rinse them in clear water for 15 minutes and call a doctor. - The charger has an oil level gauge; never unscrew this gauge because it would depressurize the installation. The oil level is only checked when changing the oil in the circuit. H1 - CLEANING THE CONDENSER AND EVAPORATOR COILS H2 - CLEANING THE PRESSURE RELIEF VALVE H3 - COLLECTING H4 - RECHARGING (*) (*) THE COOLANT TO REPLACE THE DRIER (*) COOLANT AND CHECKING THE THERMOSTATIC CONTROL AND PRESSURE SWITCHES (*) (*) : (CONSULT YOUR DEALER). 3 - 32 INTRODUCTION TO SAFETY CONTENTS 4 - ADAPTABLE ATTACHMENTS IN OPTION ON THE RANGE 4-1 INTRODUCTION TO SAFETY CONTENTS 4-2 INTRODUCTION TO SAFETY CONTENTS TABLE OF CONTENTS INTRODUCTION 4-4 PICKING 4-5 UP THE ATTACHMENTS A - ATTACHMENT WITHOUT HYDRAULICS AND HAND LOCKING DEVICE 4-5 B - ATTACHMENT WITHOUT HYDRAULICS AND HYDRAULIC LOCKING DEVICE (OPTION) 4-6 C - HYDRAULIC ATTACHMENT AND HAND LOCKING DEVICE 4-8 D - HYDRAULIC ATTACHMENT AND HYDRAULIC LOCKING DEVICE (OPTION) 4-9 4-3 INTRODUCTION TO SAFETY CONTENTS INTRODUCTION - Your lift truck is able to use interchangeable equipment. These items are called : ATTACHMENTS. - A wide range of attachments, specially designed and suitable for your lift truck are available and guaranteed by MANITOU. - The attachments are delivered with a load chart for your lift truck. The operator's manual and the load chart should be kept in the places provided on the lift truck. For standard attachments, their use is governed by the instructions contained in this manual. . IMPORTANT We would remind users that your lift truck is essentially intended for load handling. Occasional use with the buckets CBC 800/900 and CBR 900/1000 is authorized, but under no circumstances is intensive use for difficult applications (quarry, waste, cereals, agriculture, etc) permissible. In addition, use of the lift truck with the buckets CBC 800/900 and CBR 900/1000 should be with the boom completely retracted, in order to reduce the constraints on the boom head. Use of other buckets CBA, CBC, CBM, CBR, CB, CBG and manure forks FFGR is forbidden. Only attachments approved by MANITOU are to be used on our lift trucks. The manufacturer's liability will be voided in case of modification(s) without prior written permission. Maximum loads are defined by the capacity of a lift truck taking into account the attachment’s mass and center of gravity. In the event of the attachment having less capacity than the lift truck, never exceed its limit. WARNING Depending on their size, certain attachments (when the boom is lowered and/or retracted, or the tilt is activated) may come into contact with the front tires and cause damage to them. TO AVOID TIRE DAMAGE, EXTEND THE TELESCOPE TO A SUFFICIENT DISTANCE TO AVOID DAMAGING THE TIRES! 4-4 INTRODUCTION TO SAFETY CONTENTS PICKING UP THE ATTACHMENTS A - ATTACHMENT WITHOUT HYDRAULICS AND HAND LOCKING DEVICE A TAKING UP AN ATTACHMENT - Insure the attachment is in alignment to the carriage. If it is not correctly oriented, take the necessary precautions to position it safely. - Check that the locking pin and clip are in position on the bracket (fig. A). - Park the lift truck with the boom lowered in front of and parallel to the attachment, tilt the carriage forwards (fig. B). - Bring the carriage under the locking tube of the attachment, slightly lift the boom, incline the carriage backwards to position the attachment (fig. C). - Lift the attachment off the ground. HAND LOCKING - Take the locking pin and clip from the bracket (fig. A) and lock the attachment (fig. D). Do not forget to install the clip. B HAND RELEASING - Proceed in the reverse order of paragraph HAND LOCKING, insure you return the locking pin and clip to the bracket (fig. A). LAYING AN ATTACHMENT - Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT, insure you place the attachment flat on the ground and in a closed position. C D 4-5 INTRODUCTION TO SAFETY CONTENTS B1 - ATTACHMENT WITHOUT HYDRAULICS AND HYDRAULIC LOCKING DEVICE (OPTION) (UP TO S/N: 233950) A TAKING UP AN ATTACHMENT - Ensure that the attachment is in alignment to the carriage. If it is not correctly oriented, take the necessary precautions to positin it safely. - Check that the rods on the locking cylinder are retracted (fig. A). - Park the lift truck with the boom lowered in front of and parallel to the attachment, tilt the carriage forwards (fig. B). - Bring the carriage under the locking tube of the attachment, slightly lift the boom, incline the carriage backwards to position the attachment (fig. C). - Lift the attachment off the ground. HYDRAULIC LOCKING - Put the valve in position A (fig. D), the hydraulic circuit of the attachment locking open. - Push the lever of the distributor 1 (fig. E) forwards in order to lock the attachment on the carriage. - Close the valve in position B (fig. D), the hydraulic circuit of the attachment locking closed. WARNING B Always close the valve in position B (fig. D) after locking the attachment, to avoid accidental unlocking! HYDRAULIC RELEASING - Put the valve in position A (fig. D), the hydraulic circuit of the attachment locking open. - Pull the lever of the distributor 1 (fig. E) backwards to unlock the attachment. LAYING AN ATTACHMENT - Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT, insure you place the attachment flat on the ground and in a closed position. C D A B E 1 4-6 INTRODUCTION TO SAFETY CONTENTS B2 - ATTACHMENT WITHOUT HYDRAULICS AND HYDRAULIC LOCKING DEVICE (OPTION) (FROM S/N: 233951) A TAKING UP AN ATTACHMENT - Ensure that the attachment is in alignment to the carriage. If it is not correctly oriented, take the necessary precautions to positin it safely. - Check that the rods on the locking cylinder are retracted (fig. A). - Park the lift truck with the boom lowered in front of and parallel to the attachment, tilt the carriage forwards (fig. B). - Bring the carriage under the locking tube of the attachment, slightly lift the boom, incline the carriage backwards to position the attachment (fig. C). - Lift the attachment off the ground. HYDRAULIC LOCKING - Put the valve in position A (fig. D), the hydraulic circuit of the attachment locking open. - Push the lever of the distributor 1 (fig. E) to the right in order to lock the attachment on the carriage. - Close the valve in position B (fig. D), the hydraulic circuit of the attachment locking closed. WARNING B Always close the valve in position B (fig. D) after locking the attachment, to avoid accidental unlocking! HYDRAULIC RELEASING - Put the valve in position A (fig. D), the hydraulic circuit of the attachment locking open. - Pull the lever of the distributor 1 (fig. E) to the left to unlock the attachment. LAYING AN ATTACHMENT - Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT, insure you place the attachment flat on the ground and in a closed position. C D A B E 1 4-7 CONTENTS INTRODUCTION TO SAFETY C - HYDRAULIC ATTACHMENT AND A HAND LOCKING DEVICE TAKING UP AN ATTACHMENT - Insure that the attachment is in alignment to the carriage. If it is not correctly oriented, take the necessary precautions to position it safely. - Check the locking pin and clip are in position on the bracket (fig. A). - Park the lift truck with the boom lowered in front of and parallel to the attachment, tilt the carriage forwards (fig. B). - Bring the carriage under the locking tube of the attachment, slightly lift the boom, incline the carriage backwards to position the attachment (fig. C). - Lift the attachment off the ground. HAND LOCKING AND CONNECTING THE ATTACHMENT - Remove the locking pin and clip from the bracket (fig. A) and lock the attachment (fig. D). Do not forget to install the clip. - Stop the I.C. engine. - Remove the pressure from the hydraulic circuit by using the lever of the distributor 1 (fig. E). And connect the rapid (quick-release) connectors if required. IMPORTANT B Make sure that the rapid (quick-release) connectors are clean and protected with the caps provided when not in use. HAND RELEASING AND DISCONNECTING THE ATTACHMENT - Proceed in the reverse order of paragraph HAND LOCKING AND CONNECTING THE ATTACHMENT, insure you return the locking pin and clip to the bracket (fig. A). LAYING AN ATTACHMENT - Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT, insure you place the attachment flat on the ground and in a closed position. C D UP TO S/N: 233950 FROM S/N: 233951 E E 1 1 4-8 INTRODUCTION TO SAFETY D1 - HYDRAULIC ATTACHMENT (UP TO S/N: 233950) CONTENTS AND HYDRAULIC LOCKING DEVICE (OPTION) A TAKING UP AN ATTACHMENT - Insure that the attachment is in alignment to the carriage. If it is not correctly oriented, take the necessary precautions to position it safely. - Check that the rods on the locking cylinder are retracted (fig. A). - Park the lift truck with the boom lowered in front of and parallel to the attachment, tilt the carriage forwards (fig. B). - Bring the carriage under the locking tube of the attachment, slightly lift the boom, incline the carriage backwards to position the attachment (fig. C). - Lift the attachment off the ground. HYDRAULIC LOCKING AND CONNECTING THE ATTACHMENT - Put the valve in position A (fig. D), the hydraulic circuit of the attachment locking open. - Push the lever of the distributor 1 (fig. E) forwards to lock the attachment on the carriage. - Stop the I.C. engine. - Remove the pressure of the attachment hydraulic circuit by using the lever of the distributor 1 (fig. E). - Connect the rapid (quick-release) connectors as required. IMPORTANT B Make sure that the rapid (quick-release) connectors are clean and protected with the caps provided when not in use. - Close the valve in position B (fig. D), the hydraulic circuit of the attachment locking closed. WARNING Always close the valve in position B (fig. D) after locking the attachment, to avoid accidental unlocking! C HYDRAULIC RELEASING AND DISCONNECTING THE ATTACHMENT - Close the attachment. - Put the valve in position A (fig. D), the hydraulic circuit of the attachment locking open. - Push the lever of the distributor 1 (fig. E) backwards to unlock the attachment. - Stop the I.C. engine. - Remove the pressure of the attachment hydraulic circuit by using the lever of the distributor 1 (fig. E). - Disconnect the rapid (quick-release) connectors of the attachment. LAYING AN ATTACHMENT - Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT, insure you place the attachment flat on the ground and in a closed position. D A B E 1 4-9 INTRODUCTION TO SAFETY D2 - HYDRAULIC ATTACHMENT (FROM S/N: 233951) CONTENTS AND HYDRAULIC LOCKING DEVICE (OPTION) A TAKING UP AN ATTACHMENT - Insure that the attachment is in alignment to the carriage. If it is not correctly oriented, take the necessary precautions to position it safely. - Check that the rods on the locking cylinder are retracted (fig. A). - Park the lift truck with the boom lowered in front of and parallel to the attachment, tilt the carriage forwards (fig. B). - Bring the carriage under the locking tube of the attachment, slightly lift the boom, incline the carriage backwards to position the attachment (fig. C). - Lift the attachment off the ground. HYDRAULIC LOCKING AND CONNECTING THE ATTACHMENT - Put the valve in position A (fig. D), the hydraulic circuit of the attachment locking open. - Push the lever of the distributor 1 (fig. E) to the right to lock the attachment. - Stop the I.C. engine. - Remove the pressure of the attachment hydraulic circuit by using the lever of the distributor 1 (fig. E). - Connect the rapid (quick-release) connectors as required. IMPORTANT B Make sure that the rapid (quick-release) connectors are clean and protected with the caps provided when not in use. - Close the valve in position B (fig. D), the hydraulic circuit of the attachment locking closed. WARNING Always close the valve in position B (fig. D) after locking the attachment, to avoid accidental unlocking! C HYDRAULIC RELEASING AND DISCONNECTING THE ATTACHMENT - Close the attachment. - Put the valve in position A (fig. D), the hydraulic circuit of the attachment locking open. - Push the lever of the distributor 1 (fig. E) to the left to unlock the attachment. - Stop the I.C. engine. - Remove the pressure of the attachment hydraulic circuit by using the lever of the distributor 1 (fig. E). - Disconnect the rapid (quick-release) connectors of the attachment. LAYING AN ATTACHMENT - Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT, insure you place the attachment flat on the ground and in a closed position. D A B E 1 4 - 10 ">
/
Λήψη
Μια φιλική υπενθύμιση. Μπορείτε να δείτε το έγγραφο εδώ. Αλλά το πιο σημαντικό, η AI μας το έχει ήδη διαβάσει. Μπορεί να εξηγήσει πολύπλοκα πράγματα με απλούς όρους, να απαντήσει στις ερωτήσεις σας σε οποιαδήποτε γλώσσα και να σας βοηθήσει να πλοηγηθείτε γρήγορα ακόμη και στα πιο μακροσκελή ή περίπλοκα έγγραφα.
Διαφήμιση