BT-BKRNP USEFULL INSTALLATION AN TIPS

Courtesy of: DiscountCarStereo.com

BT-BKRNP

USEFULL INSTALLATION AN TIPS

The BT-BKRNP Bluetooth harness is designed exclusively for the installation of select Motorola and Parrot Bluetooth Car Kits to Becker Radios with “PHONE” menu option. These Radios are typically found in older BMW, Ferrari, Mercedes and Porsche including the popular Traffic Pro, CR-22, CDR-22, CR-220, CDR-

220, CR-210* and CDR-210*.

Why purchase the BT-BKRNP?

The BT-BKRNP harness allows for quick installation of:

Novero TrustyOne and TrulyOne

Parrot CK3100, CK3200, CK3300, CK3400, CK3500, MK6000, MK6100.

Why can’t I use the installation harness included with my Kit?

The installation harness included with the aforementioned kits can be used in most application except in vehicles equipped with factory amplifier.

The BT-BKRNP can be used in vehicle with or without amplifiers or to replace the original installation harness (purchased used and did not include the harness)

* Why can’t I use this harness to install my Hands Free with Audio streaming Bluetooth kit to the CD-210 and CDR-210 radios?

The CR-210 and CDR-210 radios (found in Porsche), does not have the “AUX IN” port required for the Audio streaming feature to work. Use the installation harness included with your kit which connects to the speaker input/outputs on the CD-210/CDR-210 radios instead. (Except vehicles with amplifier)

My radio has an existing CD Changer, AUX Adapter/iPod Adapter. Do

I have to disconnect them in order to use the BT-BKRNP?

Short answer is NO!! Bluetooth hands free features will work without disconnecting these options, however if your Bluetooth kit supports audio streaming (i.e. Novero Trusty One, CK6100 etc.) and you wish to use that feature, then the CD Changer, Auxiliary adapter or iPod adapter must be disconnected.

Installation highlights

1.

Use the radio removal tools (not included) to remove radio. (See Fig. 1)

Insert each tool into the slot on both sides of the radio until locked (a click is heard), pull radio out. To release keys from radio, push side tabs inward

(toward radio). Keys not required when re- installing radio

Fig. 1

2.

Courtesy of: DiscountCarStereo.com

For Novero: Connect the Black 24-pin Molex plug on the BT-BKRNP to the 24-pin Molex connector on the Novero control module (See Fig.2).

3.

4.

Fig. 2

For Parrot MK: Connect the Black 24-pin Molex plug on the BT-BKRNP to the 24-pin Molex connector on the MK6000, MK6100 control module

(See Fig. 2).

For Parrot CK: Connect the 10-pin and 4-pin Molex plugs on the BT-

BKRNP to the 10-pin and 4-pin Molex connector on the control module

(See Fig. 3)

5.

Fig. 3

Connect the blue ISO Plug to C-3 slot on the radio as seen in Fig. 4 below

Fig. 4

Courtesy of: DiscountCarStereo.com

Bluetooth hands free audio wires must be connected to the radio

For radios with CD Changer/iPod Adapter or Aux adapter connection:

1. Insert the white wire to #13 slot of existing blue ISO plug (See Fig. 4)

2. Insert the purple wire to # 14 slot of existing blue ISO plug (See Fig 4)

Fig. 5

For vehicles without CD Changer, Auxiliary/iPod adapters (empty slot):

1. Insert the white wire to #13 slot of included blue ISO plug

2. Insert the purple wire to #14 slot of included blue ISO plug

3. Connect the blue ISO plug into the 8-pin connector (C-3) on the back of the radio. (See Fig. 5)

Most if not all Becker radios are coded. Do not proceed to the next step if you don’t have the radio code, otherwise the radio will not operate upon reconnection.

6.

Disconnect the 8-pin Female connector “A” (See. Fig. 4) from radio and connect to Male mating 8-pin plug on harness (See Fig 6)

Fig. 6

7.

Connect Female 8-pin connector on harness to the slot vacated in step 6

This concludes the harness installation. Proceed with installation instruction for module, microphone according to manual included with Bluetooth kit.

Courtesy of: DiscountCarStereo.com

ENABLING THE AUX ON THE BECKER RADIO

Note: Becker radios without an “AUX” Menu (i.e. CD-210, CDR-210) are *NOT* compatible with this harness. For these radios you must use the harness included with the Bluetooth kit.

“AUX” Mode option will only be available after enabling it from within the menu

.

RADIOS WITH "TP" BUTTON (i.e. CR-220)

1.

2.

3.

4.

5.

6.

Turn radio "ON"

Press and hold the "TP" button for about 8 seconds until Becker 1 is displayed.

Turn the Tuning Knob until AUX OFF is displayed.

Press either button located directly under the Arrows on the display to change the present setting from OFF to ON.

Turn radio OFF.

Turn Radio back “ON” Press “CD” button to enter AUX Mode.

FERRARI with centered ☼ Button (i.e. BE6104)

1.

Turn Radio “ON”

2.

Press and hold the ☼ button (center) on the top right for about 8 seconds.

Select AUX “ON/OFF” option.

3.

Press either button located directly under the Arrows on the display to change the present setting from OFF to ON.

4.

Turn radio OFF.

5.

Turn Radio back ON press the “☼” button until “AUX” is displayed.

1.

2.

3.

4.

1.

2.

3.

4.

PORSCHE NavTraffic Pro RADIOS

Press the "Radio" button to enter Radio mode.

Press the "Nav" and "F10" simultaneously

Press "Next" until the AUX input, Changer Res screen

Press AUX to enable/disable.

LANDROVER 4775 (BECKER)

With the Radio "ON" press and hold the Tone button until the sub-menu comes up.

Press the soft-key labeled “Aux” until the screen displays “AUX Mode on”.

Press the Tone button to exit the menu.

To enter "AUX" mode, press the "CD" button and select the "AUX" softkey.

MERCEDES BENZ BE4602

1.

2.

3.

4.

5.

Turn radio ON.

Press and hold the ☼ button for 8 seconds, until Becker 1 is displayed.

Turn the Tuning Knob until AUX OFF is displayed.

Press either button located directly under the Arrows on the display to change the present setting from OFF to ON.

Turn Radio back “ON” Press “CD” button to enter AUX Mode

Courtesy of:DiscountCarStereo.com

BECKER AFTERMARKET (BE4527)

1.

2.

3.

4.

5.

1.

Turn radio ON.

Press and hold Function button #2 (center button on top right) for more than 4 seconds.

The accompanying menu appears on the display.

Press the multifunction button located directly under “AUX” on the display to change the present setting from OFF to ON.

The Setting is stored automatically. Press “CD” button to enter AUX Mode

BECKER AFTERMARKET (i.e. BE7077) Sound5

Turn radio ON.

2.

3.

4.

Press the dp (button left of present #1) repeatedly until the EXT menu appear.

Turn Rotary control knob clockwise and select EXT AUX.

Press the CD button repeatedly until “AUX” is displayed

With the Bluetooth device paired up to the Kit and the “AUX” option enabled you can now proceed to play your favorite tunes on the

Radio. If successful go ahead and re-install the radio.

© 1995-13 Discount Car Stereo. All rights reserved. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.