- Industrial & lab equipment
- Electrical equipment & supplies
- Batteries & accessories
- Non-rechargeable batteries
- User manual
ULHD6VSP and ULHD6VSC 6V LANTERN BATTERIES Specification Sheet ULHD6VSP and ULHD6VSC
Add to my manuals3 Pages
advertisement
Specification Sheet ULHD6VSP and ULHD6VSC
HEAVY DUTY ZINC CHLORIDE BATTERY
ULHD6VSP and ULHD6VSC 6V LANTERN BATTERIES
1. Scope
This specification defines the technical requirements for ULHD6VSP and ULHD6VSC super heavy duty battery.
2. Purpose
To assure that any ULHD6VSP and ULHD6VSC battery manufactured or procured by
NABC will meet or exceed our customer’s expectations.
3. Reference Document
IEC 60086-1:2000 …Primary Batteries-Part1: General
IEC 60086-2:2000 …Primary Batteries-Part2: Physical and Electrical Specification
4. Chemical System
Zinc Chloride
Mercury: Less than 1 ppm
5. Nominal Voltage: 6.0volt
6. Average Weight: 550.0g
7. Jacket: Plastic box
8. Nominal Capacity
3500mAh (Conditions: 8.2
Ω continuously discharge at 20±2 ℃ , end point voltage 3.60v)
9. Electrical Characteristics
Initialwithin30 day
After 12months
Off-load
Voltage
(v)
6.50
6.30
On-load
Voltage
(v)
5.80
5.60
Short circuit current
8.5
7.5
Acceptance Standard
GB2828 commonly
AQL=0.4
Ⅰ
conditions: 8.2Ω±0.5% load resistance, measuring time 0.3 seconds, temperature at 20±2℃,
The hairspring type ampere meter with ±0.5% accuracy (0.5level) shall be used.
sampling
10. Service Time(condition: test temp. 20 ±2℃,tested within 30 day after delivery )
Discharge Condition Average Minimum Discharge Time
Discharge load
Daily discharge time
End Point
Voltage
(v)
IEC
Standard
Initial within30day
After 12
20±2 mth
℃
at
110Ω
8.2Ω
9.1Ω
8.2Ω
12h
30min
30m/h,8h/d
24h
3.6
3.6
3.6
3.6
155h
350min
270min
/
165h
560min
560min
400min
148h
500min
500min
/
Satisfaction Standard: 9 batteries will be tested for each discharging standard.
The result of the average discharging time from each discharging standard shall be equal to or more than the average minimum time requirement.
11. Leakage & Deform
Discharge batteries until it meets the end points of the capacity data. Continue discharging at the same resistance and condition until batteries are 40% below the discharge end point. Batteries should not show any leakage or deformity through a visual inspection.
12. Caution for Use
(1) Since the battery is not manufactured to be rechargeable, there are risks of electrolyte leakage or damage to the device if the battery is charged.
(2) Battery should be installed with its “+”and “-” in the correct position.
(3) Short-circuiting, heating, disposing of fire and disassembling the battery are prohibited.
(4) Avoid using old and new batteries together.
13. Shelf Life
2 year after delivery under proper storage conditions.
14. Expiration Period Marking: a. Production date and shelf life 2 years marked on the finished cell.
b. For private label, will mark according to customer’s requirements.
15. Battery Dimension (mm): SAME DIMENSIONS FOR BOTH THE SCREW TOP
AND SPRING HEAD.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project