SyncMaster 932BWEPlus/932GWEPlus

Install driver Install programs

Notation

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Prohibited

Do not disassemble

Do not touch

Important to read and understand at all times

Disconnect the plug from the outlet

Ground to prevent an electric shock

Power

When not used for extended period of time, set your computer to DPM.

If using a screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or countries).

Do not use a damaged or loose plug.

This may cause electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage. (Class l

Equipment only.)

Insert the power plug firmly so that it does not come loose.

A bad connection may cause fire.

Do not bend the plug excessively and wire nor place heavy objects upon them, which could cause damage.

This may cause electric shock or fire.

Do not connect too many extension cords or plugs to one outlet.

This may cause fire.

Do not disconnect the power cord while using the monitor.

A surge may be caused by the separation and may damage the monitor.

Do not use the power cord when the connector or plug is dusty.

If the connector or plug of the power cord is dusty, clean it with a dry cloth.

Using the power cord with a dusty plug or connector may cause an electric shock or fire.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

This may cause electric shock or fire.

Installation

Be sure to contact an authorized Service Center , when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Place your monitor in a location with low humidity and a minimum of dust.

Failure to do so may cause electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or the person carrying it.

Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf.

Dropping the product may cause damage to the product or the person carrying it.

Do not place the product on the floor.

Take care, as someone, specifically children may trip over it.

Do not place the product on an unstable or small surface area.

Place the product on an even and stable surface, as the product may fall and cause harm to someone walking by, specifically children.

TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN

FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

Otherwise, this may cause fire.

Keep any heating devices away from the power cable.

A melted coating may cause electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.

Any increase in the internal temperature may cause fire.

Put down the monitor carefully.

Failing to do so may damage the monitor.

Do not place the monitor face down.

This may damage the TFT-LCD surface.

The installation of the bracket must be done by a qualified professional.

Installing the bracket by unqualified personnel may result in injury.

Always use the mounting device specified in the owner's manual.

When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes.

Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.

Do not disconnect the power cord while using the monitor.

A surge may be caused by the separation and may damage the monitor.

Keep the plastic packaging (bag) out of children's reach.

The plastic packaging (bag) may cause suffocation if children play with it.

Cleaning and Using

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly onto the monitor.

This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.

A dirty connector may cause electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.

Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.

Others

Do not remove the cover (or back).

This may cause electric shock or fire.

Refer to a qualified servicing company.

If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and the Service Center .

This may cause electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.

This may cause a malfunction, electric shock or fire.

In particular, avoid operating the monitor near water or outdoors where it could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center .

The monitor may malfunction, causing electric shock or fire.

Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time.

Failure to do so may cause electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the cable.

Do not cover the vents on the monitor cabinet.

Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

This may cause a malfunction, electric shock or fire.

If a foreign substance enters the monitor, unplug the power cord and contact the

Service Center .

Keep the product away from combustible chemical sprays or inflammable substances.

This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

This may cause electric shock, fire or injury.

Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc.

This may cause electric shock or fire.

If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center .

When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.

Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time.

Adjust the resolution and frequency to the level appropriate for the model.

An inappropriate resolution may cause undesirable picture quality.

19 inch Wide (48 cm) - 1440 X 900

Viewing the monitor continuously at a too close angle may result in damage to your eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor.

Do not install the product on an unstable, uneven surface or a location prone to vibrations.

Dropping the product may cause damage to the product or the person carrying it.

Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.

Failure to disconnect cables may damage it and cause fire or electric shock.

Place the product out of children's reach, as they could damage by hanging onto it.

A falling product may cause injury to the person or even fatality.

When not using the product for an extended period of time, keep the product unplugged.

Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.

Do not place your children's favorite toys or any other objects of interest on the product.

Children may try to climb on the product to retrieve an object.

The product could fall, causing injury or even fatality.

When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand.

This may cause your monitor to fall, and become damaged or cause personal injury.

Good Postures When Using the Monitor

Try to maintain a good posture when using the monitor. z z z z z z z

Keep your back straight.

Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you.

Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level.

Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits.

Keep your arms level with the back of your hands.

Keep the angle of the elbow perpendicular.

Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment) - Europe only

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

PRODUCT INFORMATION (Image Retention Free)

LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time.

This guide is to demonstrate a correct usage of LCD products in order to protect them from

Image retention.

Warranty

Warranty does not cover any damage caused by image retention.

Burn-in is not covered by the warranty.

What is Image retention ?

During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including

LCD,are subject to image retention. This is not a product defect.

Please follow the suggestions below to protect your LCD from image retention

Power Off, Screen Saver, or Power Save Mode

Ex) z

Turn the power off when using a stationary pattern.

- Turn the power off for 4 hours after 20 hours in use z z

- Turn the power off for 2 hours after 12 hours in use

Use a Screen saver if possible

- Screen saver in one color or a moving image is recommended.

Set the Monitor to power off with the PC Display Properties Power Scheme.

Suggestions for specific applications

Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems

We recommend that you follow set up of your display system program as below:

Display Information together with Logo or Moving image cycle.

Ex) Cycle : Display Information for 1 hour followed by a

Display Logo or moving image for 1 minute.

Change the Color Information periodically (Use 2 different colors).

Ex) Rotate the Color Information with 2 colors every 30 minutes.

Avoid using a combination of characters and background color with large difference in luminance.

Avoid using Grey colors, which can cause Image retention easily. z

Avoid: Colors with big difference in luminance (Black & White, Grey)

Ex) z

Recommended settings: Bright colors with little difference in luminance

- Change the characters color and background color every 30 minutes

Ex)

- Every 30 minutes, change the characters with movement.

Ex)

The best way to protect your monitor from Image retention is to set your PC or

System to operate a Screen Saver program when you are not using it.

Image retention may not occur when a LCD panel is operated under normal conditions.

Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed.

To prevent this, the accumulated voltage difference must be decreased.

Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II

Features

RTA Monitor

RTA (Response Time Accelerator)

A function that accelerates the response speed of the panel so as to provide a sharper and more natural video display.

RTA On Activates the RTA function so that the panel operates at a higher response speed than its original speed.

RTA OFF Deactivates the RTA function so that the panel operates at its original response speed.

Package Contents

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer .

Contact a local dealer to buy optional items.

Unpacking

Manual

Monitor & Simple stand

Cable

Others

Quick Setup Guide

Power Cord

Warranty Card

(Not available in all locations)

User's Guide, Monitor Driver,

Natural Color software,

MagicTune™ software

D-sub Cable

Will be applied to black and high gloss models only.

Sold separately

Your Monitor

Front

MENU button [ ]

MagicBright™ button

[ ]

Brightness button [ ]

Opens the on-screen menu and exits from the menu.

MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Custom,

Text, Internet, Game, Sport, Movie and Dynamic Contrast. Each mode has its own pre-configured brightness value. You can easily select one of seven settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.

If this is the case, adjust the brightness and contrast by using the

OSD menu.

2) Text

For documentations or works involving heavy text.

3) Internet

For working with a mixture of images such as texts and graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

7) Dynamic Contrast

Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast.

>> Click here to see an animation clip

When OSD is not on the screen, push the button to adjust brightness.

>> Click here to see an animation clip

Not available in MagicBright mode of Dynamic Contrast.

Adjust buttons [ ] Adjust items in the menu.

Enter button [ ] /

SOURCE button

Activates a highlighted menu item. /

Push the 'SOURCE', then selects the video signal while the OSD is off. (When the SOURCE button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.)

If you select the digital mode, you must connect your monitor to the graphic card's DVI IN port using the DVI cable.

AUTO button Use this button for auto adjustment.

>> Click here to see an animation clip

Use this button for turning the monitor on and off.

Power button [ ]

Power indicator This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Rear

DVI IN port

The configuration at the back of the monitor may vary from product to product.

POWER port Connect the power cord for your monitor to the power port on the back of the monitor.

Connect the DVI Cable to the DVI IN port on the back of your monitor.

RGB IN port

Kensington Lock

Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.

The Kensington lock is a device used to physically fix the system when using it in a public place.

The locking device has to be purchased separately.

For using a locking device, contact where you purchase it.

See Connecting Cables for further information regarding cable connections.

Connecting Cables

Connect the power cord for your monitor to the power port on the back of the monitor.

Plug the power cord for the monitor into a nearby outlet.

Use appropriate connection for your computer.

Using the D-sub (Analog) connector on the video card.

- Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.

[RGB IN]

Using the DVI (Digital) connector on the video card.

- Connect the DVI Cable to the DVI IN Port on the back of your Monitor.

[DVI IN]

Connected to a Macintosh.

- Connect the monitor to the Macintosh computer using the D-sub connection cable.

Turn on your computer and monitor. If your monitor displays an image, installation is completed.

Using the Stand

Folding the base

You can tilt the monitor upwards at an angle of 0° to18°.

Monitor Driver

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown below.

Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Installing the Monitor Driver (Automatic)

Insert the CD into the CD-ROM drive.

Click "Windows" .

Choose your monitor model in the model list, then click the "OK" button.

If you can see following message window, then click the "Continue Anyway" button. Then click the

"OK" button (Microsoft ® Windows ® XP/2000 Operating System).

This monitor driver is under certifying MS logo, and this installation doesn't damage your system.

The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/

Monitor driver installation is completed.

Installing the Monitor Driver (Manual)

Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux

Microsoft® Windows Vista™ Operating System

Insert your Manual CD into your CD-ROM drive.

Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".

Click "Personalization" and then "Display Settings".

Click "Advanced Settings…".

Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is.

If the message “Windows needs…” is displayed, as shown in the figure below, click "Continue".

This monitor driver is under certifying MS logo, and this installation doesn't damage your system.

The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/

Click "Update Driver…" in the "Driver" tab.

Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".

Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".

Select the model that matches your monitor from the list of monitor models on the screen, and click "Next".

Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence.

Microsoft

®

Windows

®

XP Operating System

Insert the CD into the CD-ROM drive.

Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.

Click "Display" icon and choose the "Settings" tab then click "Advanced."

Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

Click "Update Driver." and select "Install from a list or." then click the "Next" button.

Select "Don't search ,I will." then click "Next" and then click "Have disk".

Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.

If you can see following "Message" window, then click the "Continue Anyway" button. Then click the "OK" button.

This monitor driver is under certifying MS logo, and this installation doesn't damage your system.

The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/

Click the "Close" button then click the "OK" button continually.

Monitor driver installation is completed.

Microsoft

®

Windows

®

2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

Choose the "OK" button on the "Insert disk" window.

Click the "Browse" button on the "File Needed" window.

Choose A:(D:\Driver) then click the "Open" button and then click the "OK" button.

How to install

Click "Start," "Setting," and then "Control Panel."

Double click the "Display" icon.

Select the "Settings" tab and click the "Advanced Properties" button.

Choose "Monitor."

Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation

Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually.

Click "Driver" and then click "Update Driver." then click the "Next" button.

Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk".

Click the "Browse" button then choose A:(D:\Driver).

Click the "Open" button, then click the "OK" button.

Choose your monitor model and click the "Next" button then click "Next" button.

Click the "Finish" button then the "Close" button.

If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the

"Finish" button then the "Close" button.

Microsoft

®

Windows

®

Millennium Operating System

Click "Start," "Setting," and then "Control Panel."

Double click the "Display" icon.

Select the "Settings" tab and click the "Advanced Properties" button.

Select the "Monitor" tab.

Click the "Change" button in the "Monitor Type" area.

Choose "Specify the location of the driver."

Choose "Display a list of all the driver in a specific location." then click the "Next" button.

Click the "Have Disk" button.

Specify A:\(D:\driver) then click the "OK" button.

Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK".

Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.

Microsoft

®

Windows

®

NT Operating System

Click "Start," "Settings," "Control Panel," and then double-click "Display" icon.

In the Display Registration Information window, click the Settings tab and then click "All Display

Modes".

Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK".

Click the "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors, or frequency).

If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.

Linux Operating System

To execute X-Window, you need to make the X86Config file, which is a type of system setting file.

Press "Enter" at the first and the second screen after executing the X86Config file.

The third screen is for setting your mouse.

Set a mouse for your computer.

The next screen is for selecting a keyboard.

Set a Keyboard for your computer.

The next screen is for setting your monitor.

First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)

Set a vertical frequency for your monitor. (You can enter the frequency directly.)

"Enter" the model name of your monitor. This information will not affect the actual execution of X-

Window.

You have finished setting up your monitor.

Execute X-Window after setting other requested hardware.

Natural Color

Natural Color

One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. the Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications

Research Institute (ETRI).

This is only available for Samsung monitors and ensures that the color of the images on the monitor are the same as the printed or scanned images.

For more information, refer to Help (F1) in the software program.

Installing the Natural Color Software

Insert the CD included with the Samsung monitor into the CD-ROM Drive. The initial Natural Color screen will appear. Click on Natural Color in the startup window to install the Natural Color software.

To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM

Drive, click the Windows [Start] button, select [Run...] .

Enter D:\Color\NCProSetup.exe and then press the <Enter> key.

(If the drive where the CD is inserted is not D:\, enter the applicable drive.)

Uninstalling the Natural Color Software Program

Select "Settings" / "Control Panel" from the "Start" menu and then double-click "Add/Delete a

program"

Select Natural Color from the list and then click the "Add/Delete" button.

MagicTune™

Installation

1. Insert the installation CD into the CD-ROM drive.

2. Click the MagicTune™ installation file.

3. Select installation Language, Click "Next".

4. When the Installation Shield Wizard window appears, click "Next."

5. Select "I agree to the terms of the license agreement" to accept the terms of use.

6. Choose a folder to install the MagicTune™ program.

7. Click "Install."

8. The "Installation Status" window appears.

9. Click "Finish."

10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.

Double-click the icon to start the program.

MagicTune™ execution icon may not appear depending on specification of computer system or monitor.

If that happens, press F5 Key.

Installation Problems (MagicTune™)

The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment.

System Requirements

OS z z z z

Windows 2000

Windows XP Home Edition

Windows XP Professional

Windows Vista™

It is recommended using MagicTune™ in Windows™ 2000

or later.

Hardware z z

32MB Memory above

60MB Hard disk space above

* For more information, visit the MagicTune™ website .

Uninstall

The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the

Windows™ Control Panel.

Perform the following steps remove MagicTune™.

1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on

Windows™ XP, go to [Control Panel] in the [Start] menu.

2. Click the "Add or Remove Programs" icon in Control Panel.

3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™". Click on it to highlight it.

4. Click the "Change/Remove" button to remove the program.

5. Click "Yes" to begin the uninstall process.

6. Wait until the "Uninstall Complete" dialog box appears.

Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.

Control Buttons

Model

[MENU /

]

[

[ ]

]

[AUTO]

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

These buttons allow you to adjust items in the menu.

Press this button to activate a highlighted menu item.

When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.

Direct Functions

AUTO

Menu Description

AUTO

When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.

Auto adjustment allows the monitor to self-adjust to the incoming Analog signal.

The values of fine, coarse and position are adjusted automatically.

(Available in Analog mode only)

To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy.

If you change resolution in the control panel, auto function will be executed automatically.

OSD Locked & Unlock

In case of pushing AUTO button after locking OSD

In case of pushing MENU button after locking OSD

Menu

OSD Locked &

Unlock

MagicBright™

Description

This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings.

Locked : Hold down the menu button for more than five seconds to activate the

OSD adjustment lock function.

Unlock : Hold down the menu button for more than five seconds to deactivate the OSD adjustment lock function.

Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust MagicBright ( ) using the Direct button.

Menu

MagicBright™

Brightness

Description

Push the MagicBright™ button to circle through available preconfigured modes.

- Seven different modes: Custom, Text, Internet, Game, Sport, Movie and

Dynamic Contrast.

Menu

Brightness

Description

When OSD is not on the screen, push the button to adjust brightness.

SOURCE

Menu

SOURCE

Description

Selects the Video signal while the OSD is off. (Analog/Digital)

OSD Function

Picture

Color

Image

OSD

Setup

Information

Brightness

MagicColor

Coarse

Language

Auto Source

Contrast

Color Tone

Fine

H-Position

Image Reset

Color Control Gamma

Sharpness H-Position

V-Position

Color Reset

Transparency

RTA

V-Position

Display Time

Image Size

Picture : Not available in MagicBright™ mode of Dynamic Contrast.

Menu

Brightness

Description

You can use the on-screen menus to change the brightness according to personal preference.

MENU → → → → MENU

Contrast

You can use the on-screen menus to change the contrast according to personal preference.

( Not available in MagicColor mode of Full and Intelligent. )

MENU → → → → → MENU

Color : Not available in MagicBright™ mode of Dynamic Contrast.

Play/Stop

Menu Description Play/Stop

MagicColor

Color Tone

Color Control

Gamma

Image

MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.

Off

Demo

Returns to the original mode.

The screen before applying MagicColor appears on the right and the screen after applying

MagicColor appears on the left.

Full Displays not only vivid natural color but also more realistic natural skin color with clearness.

Intelligent Displays vivid natural color with clearness.

MENU → , → → → → MENU

The tone of the color can be changed and one of four modes can be selected -Cool, Normal, Warm and Custom.

( Not available in MagicColor mode of Full and Intelligent. )

MENU → → → → → → MENU

Adjusts individual Red, Green, Blue color balance. -Red, Green,

Blue

( Not available in MagicColor mode of Full and Intelligent. )

MENU → → → → → → → → MENU

Gamma correction changes the luminance of the colors with intermediate luminance.

- Mode 1

- Mode 2

- Mode 3

MENU → → → → → → MENU

Menu Description

Removes noise such as vertical stripes.

Coarse adjustment may move the screen image area. You

Play/Stop

Coarse

Fine

Sharpness

H-Position

V-Position

OSD may relocate it to the center using the horizontal control menu.

(Available in analog mode only)

MENU → → → → → MENU

Removes noise such as horizontal stripes.

If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed).

(Available in analog mode only)

MENU → → → → → → MENU

Changes the clearance of image.

( Not available in MagicColor mode of Full and

Intelligent. )

MENU → → → → → → MENU

Changes the horizontal position of the monitor's entire display.

(Available in analog mode only)

MENU → → → → → → MENU

Changes the vertical position of the monitor's entire display.

(Available in analog mode only)

MENU → → → → → → MENU

Menu

Language

Description

You can choose one of nine languages.

The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.

MENU → → → → → MENU

Play/Stop

H-Position

V-Position

Transparency

Display Time

Setup

You can change the horizontal position where the OSD menu appears on your monitor.

MENU → → → → → → MENU

You can change the vertical position where the OSD menu appears on your monitor.

MENU → → → → → → MENU

Change the transparency of the background of the OSD.

MENU → → → → → → MENU

The menu will be automatically turned off if no adjustments are made for a certain time period.

You can set the amount of time the menu will wait before it is turned off.

- 5 sec, 10 sec, 20 sec, 200 sec

MENU → → → → → → MENU

Menu

Auto Source

Image Reset

Color Reset

Description

Select Auto Source for the monitor to automatically select the signal source.

MENU → → → → → MENU

Image parameters are replaced with the factory default values.

MENU → → → → → → MENU

Color parameters are replaced with the factory default values.

MENU → → → → → → MENU

RTA (Response Time Accelerator)

A function that accelerates the response speed of the

Play/Stop

RTA

Image Size

Information panel so as to provide a sharper and more natural video display.

RTA On : Activates the RTA function so that the panel operates at a higher response speed than its original speed.

RTA Off : Deactivates the RTA function so that the panel operates at its original response speed.

MENU → → → → → → MENU

You can change the size of the screen displayed on your monitor.

Normal : The screen is displayed in accordance with the screen aspect ratio of the input signals.

Wide : A full screen is displayed regardless of the screen aspect ratio of the input signals.

This does not operate when the resolution of your

PC is set to Wide.

MENU → → → → → → MENU

Menu

Information

Description

Shows a video source, display mode on the OSD screen.

MENU → ,

Check List

Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer .

Symptom Check List Solutions

No images on the screen.

I cannot turn on the monitor.

Is the power cord connected properly?

Can you see

"Check Signal

Cable" on the screen?

Can you see "Not

Optimum Mode",

"Recommended

Mode 1440 x 900

60 Hz" on the screen?

There is no image on the screen.

Is the power

Check the power cord connection and supply.

(Connected using the D-sub cable)

Check the signal cable connection.

(Connected using the DVI cable)

If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog.

Press SOURCE/ button to have the monitor doublecheck the input signal source.

If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.

If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for

Windows ME/XP/2000) and then change the frequency of the video card.

(Refer to the Preset Timing Modes )

If the initial screen (the login screen) does not appear, contact the Service Center or your dealer .

You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.

Adjust the maximum resolution and frequency that the monitor can handle properly.

If the display exceeds SXGA or 75 Hz, a "Not Optimum

Mode", "Recommended Mode 1440 x 900 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode",

"Recommended Mode 1440 x 900 60 Hz" message appears for one minute and then disappears.

Please change to the recommended mode during this one-minute period.

(The message is displayed again if the system is rebooted.)

The monitor is in PowerSaver mode.

Press a key on the keyboard to activate the monitor and

I cannot see the

On Screen

Display.

indicator on the monitor blinking at 1 second intervals?

restore the image on the screen.

If there is still no image, press the 'SOURCE/ ' button.

Then press any key on the keyboard again to activate the monitor and restore the image on the screen.

Connected using the DVI cable?

You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals.

Connect the DVI cable and then reboot the system.

Have you locked the On Screen

Display (OSD)

Menu to prevent changes?

Unlock the OSD by pressing the [MENU / ] button for at least 5 seconds.

The screen shows strange colors or just black and white.

Is the screen displaying only one color as if looking at the screen through a cellophane paper?

Check the signal cable connection.

Make sure the video card is fully inserted in it's slot.

Reboot the computer.

Have the screen colors become strange after running a program or due to a crash between applications?

Has the video card been set properly?

Set the video card by referring to the video card manual.

The screen suddenly has become unbalanced.

Have you changed the video card or the driver?

Have you adjusted the resolution or frequency to the monitor?

Adjust screen image position and size using the OSD.

Adjust the resolution and frequency at the video card.

(Refer to the Preset Timing Modes ).

The screen can be unbalanced due to the cycle of the video card signals.

Readjust Position by referring to the OSD.

Have you adjusted the resolution or frequency on the monitor?

Adjust the resolution and frequency of the video card.

(Refer to the Preset Timing Modes ).

The screen is out of focus or OSD cannot be adjusted.

LED is blinking but no images on the screen.

Is the frequency properly adjusted when checking the

Display Timing on the menu?

There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.

Have the Windows colors been set properly?

Adjust the frequency properly by referring to the video card manual and the

(The maximum frequency per resolution may differ from product to product.)

Windows XP :

Preset Timing Modes .

Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.

Windows ME/2000 :

Set the resolution in the Control Panel → Display →

Settings.

Set the video card by referring to the video card manual.

There is a message that

Has the video card been set properly?

Have you installed the monitor driver?

Install the monitor driver according to the

Installation Instructions .

Driver

reads

"Unrecognized monitor, Plug &

Play (VESA DDC) monitor found".

See the video card manual to see if the

Plug & Play (VESA

DDC) function can be supported.

Install the monitor driver according to the

Installation Instructions .

Driver

Check when

MagicTune™ does not function properly.

MagicTune™ feature is found only on PC (VGA) with

Window OS that supports Plug and

Play.

* To check whether your PC is available for MagicTune™ feature, follow the steps below (When Windows is XP);

Control Panel → Performance and Maintenance →

System → Hardware → Device Manager → Monitors →

After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware.

MagicTune™ is an additional software for the monitor.

Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune

MagicTune™ doesn't work properly.

Have you changed your PC or video graphic card?

Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune

Did you install the program?

Reboot the computer after installing the program for the first time. If a copy of the program is already installed, remove it, reboot the computer, and then install the program again. You need to reboot the computer for it to operate normally after installing or removing the program.

Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.

Check the following items if there is trouble with the monitor.

Check if the power cord and the video cables are properly connected to the computer.

Check if the computer beeps more than 3 times when booting.

(If it does, ask the service center to check the main board of the computer.)

If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver.

Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz.

(Do not exceed 75 Hz when using the maximum resolution.)

If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel → System → Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.

If problems repeatedly occur, contact an authorized service center .

Q & A

Question Answer

How can I change the frequency?

How can I adjust the resolution?

The frequency can be changed by reconfiguring the video card.

Note that video card support can vary, depending on the version of the driver used.

(Refer to the computer or the video card manual for details.)

Windows XP :

Set the resolution in the Control Panel →

Appearance and Themes → Display → Settings.

How can I set the Power Saving function?

How can I clean the outer case/LCD Panel?

Windows ME/2000 :

Set the resolution in the Control Panel → Display →

Settings.

Contact the video card manufacturer for details.

Windows XP :

Set the resolution in the Control Panel →

Appearance and Themes → Display → Screen

Saver.

Set the function in the BIOS-SETUP of the computer.

Windows ME/2000 :

Set the resolution in the Control Panel → Display →

Screen Saver.

Set the function in the BIOS-SETUP of the computer.

Refer to the Windows / Computer Manual

Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water.

Do not leave any detergent or scratches on the case.

Do not let any water enter the monitor.

Self-Test

Self-Test Feature Check | Warning Messages | Environment | Useful Tips

Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.

Self-Test Feature Check

Turn off both your computer and the monitor.

Unplug the video cable from the back of the computer.

Turn on the monitor.

If the monitor is functioning properly, you will see a box in the illustration below.

This box appears during normal operation if the video cable becomes disconnected or damaged.

Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.

If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.

Warning Messages

If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.

Environment

The location and the position of the monitor may influence the quality and other features of the monitor.

If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.

Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet

(one meter) of the monitor.

Useful Tips

A monitor recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the monitor to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.

Judging the monitor's working condition

If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1440 x 900 60

Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on.

If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition.

In this case, check the computer for trouble.

Specifications

General

Model Name

LCD Panel

Size

Display area

Pixel Pitch

Synchronization

Horizontal

Vertical

SyncMaster 932BWPlus

19 " Wide Diagonal (48 cm)

408.24 mm (H) x 255.15 mm (V)

0.2835 mm (H) x 0.2835 mm (V)

30 ~ 81 kHz

56 ~ 75 Hz

Display Color

8 bit color (16,7M)

Resolution

Optimum resolution

Maximum resolution

1440 x 900@60 Hz

1440 x 900@75 Hz

Input Signal, Terminated

RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB

0.7 Vp-p ± 5%, TTL level (V high ≥ 2.0V, V low ≤ 0.8V)

Maximum Pixel Clock

137 MHz (Analog, Digital)

Power Supply

AC 100 - 240 V~ (+/- 10 %), 50/60 Hz

Signal Cable

15pin to 15pin D-sub cable, Detachable

DVI-D to DVI-D connector, Detachable (Option)

Dimensions (W x H x D) / Weight

449 x 374 x 199 mm / 17.7 x 14.7 x 7.8 inch / 4.1 kg / 9.0 lbs

Environmental considerations

Operating

Storage

Temperature : 50 °F ~ 104 °F (10 °C ~ 40 °C)

Humidity : 10 % ~ 80 %, non-condensing

Temperature : -4°F ~113°F (-20 °C ~ 45 °C)

Humidity : 5 % ~ 95 %, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.

Dot Acceptable

TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm

(one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problelms.

For example, the number of TFT LCD sub pixels contained in this product are 3,888,000.

Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time.

The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.

State Normal Operation Power saving mode

Power off

EPA/ENERGY 2000

Power Indicator

Power Consumption

Blue Blue, Blinking Off

Less than 42 W Less than 1 W Less than 1 W

This monitor is EPA ENERGY STAR compliant when used with a computer equipped with VESA DPMS functionality.

®

compliant and ENERGY2000

As an ENERGY STAR ® Partner, SAMSUNG has determined that this product meets the ENERGY STAR ® guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.

Display Mode

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync

Polarity

(H/V)

MAC, 640 x 480

MAC, 832 x 624

MAC,1152 x 870

IBM, 640 x 350

IBM, 640 x 480

IBM, 720 x 400

VESA, 640 x 480

VESA, 640 x 480

VESA, 800 x 600

35.000

49.726

68.681

31.469

31.469

31.469

37.500

37.861

35.156

66.667

74.551

75.062

70.086

59.940

70.087

75.000

72.809

56.250

30.240

57.284

100.000

25.175

25.175

28.322

31.500

31.500

36.000

-/-

-/+

-/-

-/-

+/+

-/-

-/-

-/-

+/-

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

37.879

48.077

46.875

60.317

72.188

75.000

40.000

50.000

49.500

+/+

+/+

+/+

VESA, 1024 x 768 48.363 60.004 65.000 -/-

VESA, 1024 x 768 56.476 70.069 75.000 -/-

VESA, 1024 x 768 60.023 75.029 78.750 +/+

VESA, 1152 x 864 67.500 75.000 108.000 +/+

VESA 1280 x 960 60.000 60.000 108.000 +/+

VESA, 1280 x 1024 63.981 60.020 108.000 +/+

VESA, 1280 x 1024 79.976

75.025

135.000

+/+

VESA, 1440 x 900 55.935

59.887

106.500 -/+

VESA, 1440 x 900 70.635

Horizontal Frequency

74.984

136.750

-/+

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.Unit : kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this

repetition is called the Vertical Frequency or Refresh Rate. Unit : Hz

Specifications

General

Model Name SyncMaster 932BWEPlus/SyncMaster 932GWEPlus

LCD Panel

Size

Display area

Pixel Pitch

Synchronization

Horizontal

Vertical

19 " Wide Diagonal (48 cm)

408.24 mm (H) x 255.15 mm (V)

0.2835 mm (H) x 0.2835 mm (V)

30 ~ 81 kHz

56 ~ 75 Hz

Display Color

8 bit color (16,7M)

Resolution

Optimum resolution

Maximum resolution

1440 x 900@60 Hz

1440 x 900@75 Hz

Input Signal, Terminated

RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB

0.7 Vp-p ± 5%, TTL level (V high ≥ 2.0V, V low ≤ 0.8V)

Maximum Pixel Clock

137 MHz (Analog, Digital)

Power Supply

AC 100 - 240 V~ (+/- 10 %), 50/60 Hz

Signal Cable

15pin to 15pin D-sub cable, Detachable

DVI-D to DVI-D connector, Detachable (Option)

Dimensions (W x H x D) / Weight

449 x 374 x 199 mm / 17.7 x 14.7 x 7.8 inch / 4.1 kg / 9.0 lbs

Environmental considerations

Operating

Storage

Temperature : 50 °F ~ 104 °F (10 °C ~ 40 °C)

Humidity : 10 % ~ 80 %, non-condensing

Temperature : -4°F ~113°F (-20 °C ~ 45 °C)

Humidity : 5 % ~ 95 %, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.

Dot Acceptable

TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm

(one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problelms.

For example, the number of TFT LCD sub pixels contained in this product are 3,888,000.

Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time.

The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.

State Normal Operation Power saving mode

Power off

EPA/ENERGY 2000

Power Indicator

Power Consumption

Blue Blue, Blinking Off

Less than 42 W Less than 1 W Less than 1 W

This monitor is EPA ENERGY STAR compliant when used with a computer equipped with VESA DPMS functionality.

®

compliant and ENERGY2000

As an ENERGY STAR ® Partner, SAMSUNG has determined that this product meets the ENERGY STAR ® guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.

Display Mode

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync

Polarity

(H/V)

MAC, 640 x 480

MAC, 832 x 624

MAC,1152 x 870

IBM, 640 x 350

IBM, 640 x 480

IBM, 720 x 400

VESA, 640 x 480

VESA, 640 x 480

VESA, 800 x 600

35.000

49.726

68.681

31.469

31.469

31.469

37.500

37.861

35.156

66.667

74.551

75.062

70.086

59.940

70.087

75.000

72.809

56.250

30.240

57.284

100.000

25.175

25.175

28.322

31.500

31.500

36.000

-/-

-/+

-/-

-/-

+/+

-/-

-/-

-/-

+/-

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

37.879

48.077

46.875

60.317

72.188

75.000

40.000

50.000

49.500

+/+

+/+

+/+

VESA, 1024 x 768 48.363 60.004 65.000 -/-

VESA, 1024 x 768 56.476 70.069 75.000 -/-

VESA, 1024 x 768 60.023 75.029 78.750 +/+

VESA, 1152 x 864 67.500 75.000 108.000 +/+

VESA 1280 x 960 60.000 60.000 108.000 +/+

VESA, 1280 x 1024 63.981 60.020 108.000 +/+

VESA, 1280 x 1024 79.976

75.025

135.000

+/+

VESA, 1440 x 900 55.935

59.887

106.500 -/+

VESA, 1440 x 900 70.635

Horizontal Frequency

74.984

136.750

-/+

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.Unit : kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this

repetition is called the Vertical Frequency or Refresh Rate. Unit : Hz

CHILE

COLOMBIA

COSTA RICA

ECUADOR

EL SALVADOR

GUATEMALA

JAMAICA

PANAMA

PUERTO RICO

REP. DOMINICA

TRINIDAD &

TOBAGO

VENEZUELA

Europe

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the

SAMSUNG customer care center.

North America

U.S.A

CANADA

MEXICO

Latin America

ARGENTINE

1-800-SAMSUNG (726-7864)

1-800-SAMSUNG (726-7864)

01-800-SAMSUNG (726-7864) http://www.samsung.com/us http://www.samsung.com/ca http://www.samsung.com/mx http://www.samsung.com/ar

BRAZIL

0800-333-3733

0800-124-421

4004-0000

800-SAMSUNG(726-7864)

01-8000112112

0-800-507-7267

1-800-10-7267

800-6225

1-800-299-0013

1-800-234-7267

800-7267

1-800-682-3180

1-800-751-2676 http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com.co

http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

1-800-SAMSUNG(726-7864)

0-800-100-5303 http://www.samsung.com/latin http://www.samsung.com/latin

GERMANY

HUNGARY

ITALIA

LUXEMBURG

NETHERLANDS

NORWAY

POLAND

PORTUGAL

REPUBLIC OF

IRELAND

SLOVAKIA

SPAIN

SWEDEN

SWITZERLAND

U.K

CIS

ESTONIA

LATVIA

LITHUANIA

KAZAHSTAN

KYRGYZSTAN

RUSSIA

UKRAINE

UZBEKISTAN

Asia Pacific

AUSTRIA

BELGIUM

CZECH REPUBLIC

DENMARK

FINLAND

FRANCE

0800-SAMSUNG(726-7864)

02 201 2418

844 000 844

70 70 19 70

030-6227 515

3260 SAMSUNG(726-7864)

08 25 08 65 65 (€ 0,15/min)

01805-SAMSUNG(726-7864)

(€ 0,14/Min)

06-80-SAMSUNG(726-7864)

800-SAMSUNG(726-7864)

0035 (0)2 261 03 710

0900 SAMSUNG(726-7864)

(€ 0,10/Min)

815-56 480

0 801 801 881

022-607-93-33

80 8 200 128

0818 717 100

0800-SAMSUNG(726-7864)

902 10 11 30

0771-400 200

0800-SAMSUNG(726-7864)

0870-SAMSUNG(726-7864)

800-7267

800-7267

8-800-77777

8-10-800-500-55-500

00-800-500-55-500

8-800-555-55-55

8-800-502-0000

8-800-120-0-400 www.samsung.com/at http://www.samsung.com/be http://www.samsung.com/cz http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de

http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.com/be http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/ie http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/ch http://www.samsung.com/uk http://www.samsung.ee

http://www.samsung.com/lv http://www.samsung.lt

http://www.samsung.kz

http://www.samsung.ru

http://www.samsung.ua

http://www.samsung.uz

AUSTRALIA

CHINA

HONG KONG

INDIA

INDONESIA

JAPAN

MALAYSIA

NEW ZEALAND

PHILIPPINES

SINGAPORE

THAILAND

TAIWAN

VIETNAM

Middle East & Africa

SOUTH AFRICA

TURKEY

U.A.E

1300 362 603

800-810-5858, 010- 6475 1880

3698-4698

3030 8282

1800 110011

0800-112-8888

0120-327-527

1800-88-9999

0800SAMSUNG(726-7864)

1800-10-SAMSUNG(726-7864)

1800-SAMSUNG(726-7864)

1800-29-3232, 02-689-3232

0800-329-999

1 800 588 889

0860-SAMSUNG(726-7864 )

444 77 11

800-SAMSUNG (726-7864)

8000-4726 http://www.samsung.com/au http://www.samsung.com.cn

http://www.samsung.com/hk http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/nz http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw http://www.samsung.com/vn http://www.samsung.com/za http://www.samsung.com.tr

http://www.samsung.com/mea

Terms

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit : mm

Vertical Frequency

The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate.

Unit : Hz

Example : If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency.

Unit : kHz

Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-

Interlace method while showing odd lines and then even lines in turn is called the Interlace method.

The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace

method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA

DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called the

'resolution'. This number shows the accuracy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen.

Example :If the resolution is 1440 x 900 , this means the screen is composed of 1440 horizontal dots (horizontal resolution) and 900 vertical lines (vertical resolution).

For Better Display

Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD.

Resolution : 1440 x 900

Vertical frequency (refresh rate) : 60 Hz

TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm

(one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen.

This is not from bad quality and you can use it without uneasiness.

For example, the number of TFT LCD sub pixels that is contained in this product are 3,888,000.

When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the LCD area but rub softly.

If excessive force is applied, you can have a stain on it.

If you are not satisfied with the picture quality, you can get better quality of picture by performing the

"auto adjustment function" in display screen that is appeared as window termination button is pressed.

If there's still noise after the automatic adjustment, use the FINE/COARSE adjustment function.

When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear.

Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time.

Authority

Information in this document is subject to change without notice.

© 2007 Samsung Electronics Co., Ltd. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.,

Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and

Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY

STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY

STAR® guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.