Zebra EM220 Owner Manual

EM220II

Mobile Printer

Net Configuration Tool

P1007752-022

Rev. 1.00

EM220II

Table of Contents

1. Manual Information ........................................................................................................ 6

2. Operating System (OS) Environment ........................................................................... 6

3. Software Installation & Deletion ................................................................................... 7

3-1 Installation .................................................................................................................. 7

3-2 Deletion ...................................................................................................................... 9

4. Configuration ............................................................................................................... 10

4-1 Serial / USB Configuration ........................................................................................ 10

4-2 WLAN Configuration ................................................................................................. 15

4-3 Web browser............................................................................................................. 19

Rev. 1.00 - 2 - Mobile Printer


EM220II

■ Proprietary Statements

This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.

Product Improvements

Since continuous product improvement is a policy of Zebra Technologies Corporation, all specifications and signs are subject to change without notice.

FCC Compliance Statement

NOTE: This equipment has been tested and found to comply with the limits or a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet or circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure requirements this device shall be used in accordance with the operating conditions and instructions listed in this manual.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to insure compliance.

Changes or modifications to this unit not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate this equipment.



EM220II

Canadian Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

“IC:” before the equipment certification number signifies that the Industry Canada technical specifications were met. It does not guarantee that the certified product will operate to the user’s satisfaction.

Liability Disclaimer

Inasmuch as every effort has been made to supply accurate information in this manual,

Zebra Technologies Corporation is not liable for any erroneous information or omissions.

Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom.

No Liability for Consequential Damage

In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or the results of use of or inability to use such product, even if Zebra Technologies Corporation has been advised of the possibility of such damages.

Because some states do not allow the exclusion of liability for consequential or incidental damages, the above limitation may not apply to you.



EM220II

Copyrights

The copyrights in this manual and the label print engine described therein are owned by

Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software in the label print engine may result in imprisonment of up to one year and fines of up to

$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.

This product may contain ZPL® , ZPL II® , and ZebraLinktm programs; Element Energy

Equalizer® Circuit; E3® ; and AGFA fonts. Software © ZIH Corp. All rights reserved worldwide.

ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,

ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of

ZIH Corp. All rights reserved worldwide.

Monotype® , Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions.

AndyTM , CG PalacioTM, CG Century SchoolbookTM, CG TriumvirateTM, CG TimesTM,

Monotype KaiTM, Monotype MinchoTM and Monotype SungTM are trademarks of

Monotype Imaging, Inc. and may be registered in some jurisdictions.

HY Gothic HangulTM is a trademark of Hanyang Systems, Inc.

AngsanaTM is a trademark of Unity Progress Company (UPC) Limited.

Andale® , Arial® , Book Antiqua® , Corsiva® , Gill Sans® , Sorts® and Times New Roman® are trademarks of The Monotype Corporation registered in the United States Patent and

Trademark Office and may be registered in certain jurisdictions.

Cent ury Gothic™, Bookman Old StyleTM and Century SchoolbookTM are trademarks of

The Monotype Corporation and may be registered in certain jurisdictions.

HGPGothicB is a trademark of the Ricoh company, Ltd. and may be registered in some jurisdictions.

UniversTM is a trademark of Heidelberger Druckmaschinen AG, which may be registered in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger Druckmaschinen AG.

Futura® is a trademark of Bauer Types SA registered in the United States Patent and

Trademark Office and may be registered in some jurisdictions.

TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions.

All other product names are the property of their respective owners.

All other brand names, product names, or trademarks belong to their respective holders.

© 2006 ZIH Corp.



EM220II

1. Manual Information

This Net Configuration Tool Manual provides information on the utility program used to set printer operation conditions.

2. Operating System (OS) Environment

The following operating systems are supported for usage.

- Microsoft Windows XP (32bit/64bit)

- Microsoft Windows 2003 Server (32bit/64bit)

- Microsoft Windows Embedded For Point Of Service

- Microsoft Windows VISTA (32bit/64bit)

- Microsoft Windows 2008 Server (32bit/64bit)

- Microsoft Windows 7 (32bit/64bit)

- Microsoft Windows 8 (32bit/64bit)



3. Software Installation & Deletion

3-1 Installation

1) Execute the “Net Configuration Setup_V1.x.x.exe” file.

(This file must first be downloaded.)

2) Click the “Next” button.

EM220II



3) Click the “Next” button.

(Install to: C:\Program Files\Zebra Technologies\Net Configuration Setup)

EM220II

4) Installation will b e completed on click the “Finish” button.



3-2 Deletion

1) Click and activate the “Programs and Features” icon in the Control Panel.

2) Select “Net Configuration Setup” and click the “Uninstall” button.

EM220II

3) Click the “Yes” button to completely remove the application.



4. Configuration

Install and execute NetConfiguration.exe involved in CD.

(Start>>Zebra>>NetConfiguration.exe)

4-1 Serial / USB Configuration

Connect to Serial/USB cable, then click “Serial/USB Configuration”.

EM220II



EM220II

1

) Choose the “Port”, then click “Connect”.

If it is properly connected, “Succeeded to printer connection” will be shown. Then the configuration of the printer will be listed.

2) System & Information

Printer Name, Printer Port, User ID, User password can be set.



3) Protocol

You can set HTTPS, TELNET, FTP and SNMP protocol as able or disable.

SNMP can be also set.

EM220II

4) BSS Information

When you click “Get BSS information”, close AP information will be listed.



EM220II

5) Network

You can set Infrastructure/Adhoc, SSID, IP, Subnetmask and Gateway.

By setting “Inactivity Time”, you can disconnect the printer to host device when the data is not transferred while inactivity time. If multiple host devices are used with one printer,

“Inactivity Time” is recommended. (Other host devices are restricted to use a printer if one host device keep connecting to a printer.)

6) Authentication

You can set Authentication and Cryptograph. If it is Infrastructure mode, you need to set

Cryptograph with AP for proper connection. Then if it is Adhoc mode, you need to set

Cryptograph with host device.



EM220II

7) Certificate

Printer can save the certificate file for EAP-TLS certification.

When you use TLS certification, CA certificate(PEM, Client Key(KEY/PEM), and client certificate(PEM) file should be uploaded. The key size of certificate recommended is 512.

If the size of certificate is more than 512, it will take some time for EAP certification.



EM220II

4-2 WLAN Configuration

To set the WLAN, PC and Printer should be in a same network.

(AP, PC, Printer network mode, SSID, encryption, authentication has to be set the same way)

Connect to WLAN cable, then click “WLAN Configuration”.

1) When you press the Search button, the printer connected to the network will be shown in the list.



EM220II

2) Select the printer from the list and press the [Setting] button, and then the following window for changing the WLAN settings will pop up.

3) Enter the proper IP Address, Subnet Mask, and Gateway of the currently used network, and then click the [Save] button to save the settings.

(Device Baudrate setting, which is used for other models, is not necessary for our printer.)

4) Select the printer from the list and press the [Configuration(web)] button, and then the

Login window will pop up.



5) Enter the ID and Password set in the printer, and click OK.

(Default settings are ID: “admin”, Password: “password”)

EM220II

6) When you log in, you will see the web browser for changing the WLAN settings as shown below.



EM220II

7) You can search for the information of the wireless network by pressing the BSS Info button.

8) When you press the BSS Info button, information about the SSID, BSSID, Network

Model, and Encryption information of the network in close range will be shown as follows.



EM220II

4-3 Web browser

Our printer supports the security enhanced https protocol as well as http. When SSL of the webserver of our printer is enabled, you must enter the address with “https” instead of

“http” in the address bar to connect to the web-server.

(Automatic connection will be made when connecting with the configuration tool.)

When SSL of the web-server is enabled,

* a security warning window will pop when you try to connect with https.

Accept the certificate provided by the printer in the warning window and continue.

When SSL of the web-server is disabled,

1) Enter the IP address of the printer in the address bar, and the following login window will pop up.

Enter the ID and Password set for the printer, and then click [OK]

(Default setting values are ID: “admin”, Password: “password”.)



EM220II

2) When the ID and Password match the ones registered in the printer, the following window will be opened.

WLAN configuration is possible.

Home, System, Protocol, Network (WLAN), and Authentication can be configured from this window, and the wizard mode is also provided for easier step by step configuration.



www.zebra.com

Zebra Technologies International, LLC Zebra Technologies Europe Limited

333 Corporate Woods Parkway Dukes Meadow

Vernon Hills, Illinois 60061, 3109 USA Millboard Road

Phone: +1.847.634.6700 Bourne End

Toll-Free: +1.800.423.0422 Buckinghamshire, SL8 5XF, UK

Fax: +1.847.913.8766 Phone: +44 (0)1628 556000

Fax: +44 (0)1628 556001

Zebra EM220 Owner Manual

Mobile Printer

Net Configuration Tool

Table of Contents

■ Proprietary Statements

1. Manual Information

2. Operating System (OS) Environment

3. Software Installation & Deletion

4. Configuration

Related manuals

Zebra EM220 Owner Manual

Mobile Printer

Net Configuration Tool

Table of Contents

■ Proprietary Statements

1. Manual Information

2. Operating System (OS) Environment

3. Software Installation & Deletion

4. Configuration

Related manuals

Zebra

EM220

Zebra

EM220

Zebra

EM220

Zebra

EM220

Zebra

SAMSUNG

Zebra

EM220

Zebra

EM220

Zebra

EM220

Zebra

EM220