Simplicity Dress, Top, Jacket, Pants Sewing Pattern User Manual

English/Spanish 3
1/4
Web Site
U.S. & Canada Toll-Free
General Directions
6
The Pattern
3
2
SYMBOLS
GRAIN LINE Place on
straight grain of fabric
parallel to selvage
8
7
11
10
9
C
12
13
B
PLACE SOLID LINE on
fold of fabric.
CENTER FRONT OR
BACK of garment.
18
17
NOTCHES
15
DOTS
ADJUST IF NEEDED
Make adjustments before placing
pattern on fabric.
TO LENGTHEN:
Cut pattern
between
lengthen or
shorten lines.
Spread pattern
evenly, the
amount needed
and tape to
paper.
CUTTING LINE
16
A
SEAM ALLOWANCE: 5/8" (1.5cm)
unless otherwise stated is included but
not printed on MULTI-SIZE PATTERNS.
Mark your size with colored felt tip pen.
See chart on tissue for how to use MULTISIZE PATTERNS.
C
B
D
A
D
1-BODICE FRONT -A,B
10-BACK -C
2-BODICE SIDE FRONT -A,B
11-LOOP -C
3-BODICE BACK -A,B
12-FRONT FACING -C
4-FRONT BAND -A,B
13-BACK FACING -C
5-BACK BAND -A,B
14-SLEEVE -C
6-SHOULDER STRAP -A,B
15-YOKE FRONT -D
7-SKIRT FRONT -A,B
16-YOKE BACK -D
8-SKIRT BACK -A,B
17-FRONT -D
9-FRONT -C
18-BACK -D
pattern printed
side down
★
✻
pattern printed
side up
1
See
SPECIAL
CUTTING
NOTES
SELVAGES
7
5
FOLD
4 FOLD
6
WITH NAP
2B 44" 45" (115CM)
8
2
WITH NAP
7
SELVAGE
4 5 FOLD
1
10
3 2
FOLD
WITH NAP
SIZES 6 8 10 12 14
7
5
4 FOLD
44" 45" (115CM) CON PELUSA
TALLAS 16 18 20 22 24
1C
58" 60" (150CM) CON PELUSA
TALLAS 6 8 10 12 14
1D
58" 60" (150CM) CON PELUSA
TALLAS 16 18 20 22 24
★
13
SELS.
6
WITH NAP
SIZES 6 8 10 12 14 16 18
10
5
8
4
ALL SIZES
© Copyright 2010—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
2B
44" 45" (115CM) CON PELUSA
TALLAS 16 18 20 22 24
2C
58" 60" (150CM) CON PELUSA - TODAS LAS TALLAS
A,B ENTRETELA USE LAS
13
3
4D 58" 60" (150CM)
WITH NAP
SIZES 20 22 24
9
12
4 SELVAGE
SEL.
6 FOLD
44" 45" (115CM) CON PELUSA
4B
44" 45" (115CM) CON PELUSA
TALLAS 12 14 16 18 20 22 24
4C
58" 60" (150CM) CON PELUSA
TALLAS 6 8 10 12 14 16 18
4D
58" 60" (150CM) CON PELUSA
TALLAS 20 22 24
SELVAGE
SEL.
12
4E 20" TO 25" (51CM TO 64CM) FUSIBLE
ALL SIZES
CUTTING LAYOUTS CONTINUE ON PAGE 2
4A
TALLAS 6 8 10
INTERFACING
USE PIECES 12 13
5
C CHAQUETA USE LAS PIEZAS 9 10 11 12 13 14
11
13
10
13
FOLD
PIEZAS 4 5 6
20" A 25" (51CM A 64CM) ADHESIVA
TODAS LAS TALLAS
CORTE UNA PIEZA 11
14
FOLD
A,B INTERFACING
3 20" TO 25" (51CM TO 64CM) FUSIBLE
2A
14
SELVAGES
SELS.
USE PIECES 4 5 6
12
PIEZAS 1 2 3 4 5 6 7 8
44" 45" (115CM) CON PELUSA
TALLAS 6 8 10 12 14
FOLD
2 3
7
B BLUSA USE LAS
11
9
FOLD
1
ALL SIZES
1
6
SELS.
6
1B
14
FOLD
8
11
44" 45" (115CM) CON PELUSA
TALLAS 6 8 10 12 14
9
FOLD
1C 58" 60" (150CM)
1A
12
11
FOLD
WITH NAP
FOLD
10
4C 58" 60" (150CM)
8
3
2C 58" 60" (150CM)
7
9
FOLD
5 FOLD
SEL.
3
USE LAS PIEZAS 1 2 3 4 5 6 7 8
14
12
5
4
SELVAGE
b.
A VESTIDO
WITH NAP
4 FOLD
SELVAGES
1
2
Turn one fabric
layer around so
arrows on both
layers go in the
same direction.
Place RIGHT sides
together (b).
SELVAGES
SELVAGES
CUT ONE OF PIECE 11
SIZES 12 14 16 18 20 22 24
SELVAGE
Español
SELVAGES
6
SIZES 16 18 20 22 24
SELVAGES
8
4
a.
SELVAGES
WITH NAP
SELS.
7
FOLD
8
selvages indicating
direction of nap or
design. Fold fabric
crosswise with
RIGHT sides
together, and cut
along fold (a).
Open out
fabric to single
thickness. Cut
extending
piece on
RIGHT side of
fabric in
position
shown.
C JACKET
4B 44" 45" (115CM)
3 2
1
2 3
SELS.
Mark small
✻
arrows along both
SELVAGES
FOLD
5
6
FOLD
SEL.
★
If layout
shows a piece
extending past
fold, cut out all
pieces except
piece that
extends.
13 FOLD
SIZES 6 8 10 12 14
6
SPECIAL CUTTING NOTES
4A 44" 45" (115CM)
FOLD
WITH NAP
WITH NAP
1B 44" 45" (115CM)
8
B TOP
SELVAGE
• FOR PILE, SHADED OR ONE WAY
DESIGN FABRICS: Use “with nap”
layouts
Notch outer
curves
SIZES 6 8 10
2A 44" 45" (115CM)
SIZES 6 8 10 12 14
SELS.
FOLD
USE PIECES 1 2 3 4 5 6 7 8
• Pin mark dots.
USE PIECES 9 10 11 12 13 14
SELS.
USE PIECES 1 2 3 4 5 6 7 8
1
5 FOLD
3
7
A DRESS
1A 44" 45" (115CM)
4
Clip inner
curves
• Snip edge of fabric to mark
notches, ends of fold lines and
center lines.
• FOR SINGLE THICKNESS: Place
fabric RIGHT side up.
SEW garment following Sewing Directions.
PIN or machine-baste seams matching notches.
STITCH 5/8" (1.5 cm) seams unless otherwise stated.
PRESS seams open unless otherwise indicated clipping when necessary so
seams will lie flat.
• TRIM seams to reduce bulk, as shown below.
2
SIZES 16 18 20 22 24
POSITION OF PATTERN PIECES MAY VARY SLIGHTLY ACCORDING
TO YOUR PATTERN SIZE
SIZES 16 18 20 22 24
6
WITH NAP
• FOR DOUBLE THICKNESS: Fold
fabric with RIGHT sides together.
•
•
•
•
FOLD
1D 58" 60" (150CM)
To Quick Mark:
PIN pattern to fabric as shown in Cutting
Layouts.
When lengthen or shorten lines are
not given, make adjustments at
lower edge of pattern.
Trim corners
AFTER CUTTING:
Transfer markings to WRONG side
of fabric before removing pattern.
Use pin and chalk method or
dressmaker’s tracing paper and
wheel.
CIRCLE your cutting layout.
Sewing
Trim enclosed
seams into layers
Cutting
Layouts
BEFORE CUTTING:
PRESS pattern pieces with a warm dry
iron. PRE-SHRINK fabric by pre-washing
washables or steam-pressing nonwashables.
TO SHORTEN:
At lengthen or
shorten lines,
make an even
pleat taking up
amount needed.
Tape in place.
LENGTHEN OR
SHORTEN LINES
14
Cutting/Marking
SELVAGE
1
5
[email protected]
CROSSWISE FOLD
4
Thank you for purchasing this Simplicity pattern.
We have made every effort to provide you with a high quality product.
Gracias por haber comprado este patrón de Simplicity.
Hemos hecho todos los esfuerzos para ofrecerle un producto de alta calidad.
http://www.simplicity.com
1-888-588-2700
18 pieces given
E-mail
e
✁
2373
®
ENTRETELA USE LAS
4E
PIEZAS 12 13
20" A 25" (51CM A 64CM) ADHESIVA
TODAS LAS TALLAS
CONTINUACIÓN DE LOS DIAGRAMAS DE CORTE
EN LA PÁGINA 2
English/Spanish 3
2373
Español
2/4
D PANTS
5B
17
WITH NAP
17
WITH NAP
SIZES 6 8 10
16
5C 58" 60" (150CM)
18
5C
SEL.
18
16
FOLD
FOLD
5D 58" 60" (150CM)
WITH NAP
15 16
17
SIZES 14 16 18 20 22 24
18
15 16
Sewing Directions
STAY-STITCHING
FABRIC
KEY
2
RIGHT SIDE
WRONG SIDE
INTERFACING
FOLD
11
10
ENTRETELA USE LAS
15
16
6
PIEZAS 15 16
20" A 25" (51CM A 64CM) ADHESIVA
TODAS LAS TALLAS
SELS.
LINING
11. To gather upper edge of skirt front between small dots, stitch
along seam line and 1/4” (6mm) INSIDE seam line, using a
long machine-stitch. Gather upper edge of skirt back
between notches in same manner.
DRESS A, TOP B
4
TALLAS 14 16 18 20 22 24
10. On OUTSIDE, pin straps to upper edge of front band,
matching small and large dots; baste.
Read General Directions on page 1 before you begin.
3
SELS.
Selvage (s) / sel. (s) = Orillo(s)
Crosswise Fold= Doblez transversal
Fold= Doblez
18
FOLD
1
ALL SIZES
SELVAGES
17
58" 60" (150CM) CON PELUSA
5D 58" 60" (150CM) CON PELUSA
FOLD
6 20" TO 25" (51CM TO 64CM) FUSIBLE
SELVAGES
44" 45" (115CM) CON PELUSA
TALLAS 6 8 10 12
5B 44" 45" (115CM) WITH NAP
SIZES 12 14 16 18 20 22 24
44" 45" (115CM) CON PELUSA
TALLAS 6 8 10
TALLAS 12 14 16 18 20 22 24
15
SIZES 6 8 10 12
15
5A
SEL.
CROSSWISE
FOLD
SELVAGES
5A 44" 45" (115CM)
USE LAS PIEZAS 15 16 17 18
USE PIECES 15 16
SELVAGES
USE PIECES 15 16 17 18
D PANTALóN
INTERFACING
FOLD
1. Stay-stitch upper edge of bodice front and bodice side front
1/2" (1.3cm) from cut edges in direction of arrows.
This stitching stays in permanently and helps prevent
stretching on curved edges.
Stay-stitching will not be shown in the following illustrations.
12. WIth RIGHT sides together, stitch skirt front to skirt back at
side seams, leaving LEFT side seam open above notch.
Back-stitch at notch to reinforce seam.
12
13
2. With RIGHT sides together, stitch bodice front to bodice side
front at side front seams. Press seams toward bodice front.
3. On OUTSIDE of bodice front, pin one edge of ribbon for View
A or straight edge of narrow lace for View B along seam.
Stitch close to long edges of ribbon or straight edge of lace.
13. With RIGHT sides together, pin skirt to bodice, matching
centers, RIGHT side seams and placing bodice side front
seams at small dots, having opening edges even. Pull up
gathering stitches to fit. Baste. Stitch. Press seam toward
bodice.
4. Stitch bodice front to bodice back at RIGHT side seam.
NOTE: You have cut out two front band, two back band and four
shoulder strap sections. One front band, one back band and two
shoulder strap sections will be referred to as facings.
5
14. With RIGHT sides together, stitch band facing sections
together at RIGHT side seam. To EDGE FINISH notched
edge...stitch 1/4" (6mm) from edge, turn under along stitching
and stitch OR zig-zag over the edge OR overlock/serge over
the edge.
14
5. Apply fusible interfacing to WRONG side of front and back
band sections, following manufacturer’s directions. With
RIGHT sides together, stitch front band to back band at
RIGHT side seam.
15
6
6. With RIGHT sides together, pin upper edge of bodice to lower
edge of band, matching centers, RIGHT side seams and
having raw edges even. Stitch. Trim seam; clip curves. Press
seam toward band.
7
8
7. With RIGHT sides together, pin facing and shoulder strap
sections together, having raw edges even. Stitch long edges,
leaving ends with small and large dots open. Trim seam; clip
curves.
8. Turn straps RIGHT side out; press. Baste raw edges
together.
9
9. On OUTSIDE, pin one edge of ribbon for View A or straight
edge of narrow lace for View B along finished edges of strap.
For View A, stitch close to long edges of ribbon. For View B,
stitch close to straight edge of lace.
© Copyright 2010—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
16
15. With RIGHT sides together, pin facing to upper edge of band,
matching centers, RIGHT side seams and small and large
dots. Stitch, leaving open between small and large dots on
back band. Trim seam; clip curves.
16. Turn facing to INSIDE; press. Slip back edges of straps into
openings on back band, matching small and large dots.
Pin.You will notice that the straps have extra allowance at the
back edge. This is for adjustment. Try garment on and adjust
as necessary. Pin.
Open out back band facing and stitch across openings,
catching in ends and connecting with previous stitching. Trim
seam allowances evenly if necessary.
English/Spanish 3
2373
3/4
3
3. Fold loop in half, lengthwise, with RIGHT sides together.
Stitch a scant 1/4" (6mm) from fold edge, stretching loop
while stitching. With a needle, attach a strong thread to one
end of loop.
17
5
4
17. Turn facing back to INSIDE. Baste LEFT side edges together.
On OUTSIDE, baste lower edge of band along seam through
all thicknesses. Pin one edge of ribbon for View A or straight
edge of narrow lace for View B along upper edge of band.
Stitch close to long edges of ribbon or straight edge of lace.
Apply another row of ribbon or lace to lower edge of band
along seam.
4. Draw needle eye forward, through fold, turning loop RIGHT
side out. Cut two loops each 2-3/4" (7cm) long.
5. On OUTSIDE, pin loops to RIGHT front edge at small dots,
having one edge of loop at small dot and remaining edge 1/2”
(1.3cm) below, as shown. Baste across ends.
7
6
7. Pin fusible interfacing to WRONG side of front and back
facing sections. Cut diagonally across corners that will be
enclosed with seams. Fuse interfacing in place, following
manufacturer’s directions.
Stitch shoulder seams of facing sections.
To EDGE FINISH unnotched edge...stitch 1/4" (6mm) from
edge, turn under along stitching and stitch OR zig-zag over
the edge OR overlock/serge over the edge.
18. Press under 5/8" (1.5cm) on LEFT front opening edge and
1/2" (1.3cm) on LEFT back opening edge.
Pin LEFT back edge to zipper tape, placing pressed edge
close to zipper teeth and tab end of zipper 3/8” (1cm) below
upper edge of opening. Turn upper end of zipper tape over
seam allowance.
Pin and baste LEFT front edge to zipper tape, lapping LEFT
front 1/8" (3mm) over LEFT back. Turn upper end of zipper
tape over seam allowance. Baste.
Stitch as basted, using an adjustable zipper foot. Sew a hook
and eye at neck edge when garment is finished.
18
8
9
8. With RIGHT sides together, pin facing to garment, matching
centers back and shoulder seams. Stitch front and neck
edges. Trim seam and corners; clip curves.
19. Mark length. Press up hem along marking. Mark depth of
hem; trim evenly. Press under 1/4" (6mm) on raw edge. Stitch
close to inner pressed edge.
19
20
21
1
9. Turn facing to INSIDE, turning loops out; press. To keep the
facing from rolling to OUTSIDE, secure it at the seam
allowances by tacking it by hand, stitching in the ditch or
using a small piece of fusible web.
20. FOR VIEW A - On OUTSIDE, pin ribbon to garment 6”
(15cm) from lower edge, turning under and lapping one end
at one side seam. Stitch close to long edges of ribbon. Slipstitch turned under and lapped ends.
21. FOR VIEW B - On OUTSIDE, pin straight edge of wider lace
to garment 4” (10cm) from lower edge, turning under ends at
one side.seam. Stitch close to straight edge of lace. Slipstitch turned under ends.
10. Open out one edge of bias tape.
10
11
11. With RIGHT sides together, pin tape to lower edge of sleeve,
placing crease along the 3/8” (1cm) seam line. Stitch in a 3/8”
(1cm) seam. Trim seam, being careful not cut tape.
JACKET C
1. Stay-stitch front and back neck edges 1/2" (1.3cm) from cut
edge in direction of arrows.
This stitching stays in permanently and helps prevent
stretching on curved edges.
Stay-stitching will not be shown in the following illustrations.
2
6. With RIGHT sides together, stitch fronts to back at shoulder
and side seams.
2. To make dart in front with RIGHT sides together, fold the
fabric through the center of the dart, bringing broken lines
and small dots together. On INSIDE, place pins at RIGHT
angles to the broken lines. Stitch the dart from wide end to
point.
TIP- To prevent a “bubble” at the point, make the last few
stitches right on the fold and leave the thread ends long
enough to tie a knot. DO NOT back-stitch at the point.
Press the dart flat along the stitching to “blend” the stitches,
then press dart down.
© Copyright 2010—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
12. Turn tape to INSIDE; press. Baste close to inner edge. On
OUTSIDE, top-stitch as basted. To gather top of sleeve
between small dots, stitch along the 3/8” (1cm) seam line and
1/4” (6mm) INSIDE seam line, using a long machine-stitch.
13
12
13. With RIGHT sides together, pin sleeve to armhole edge,
placing center small dot at shoulder seam, matching
remaining small and large dots. Pull up gathering stitches to
fit. Baste.
14. Open out one edge of bias fold tape.
14
15
15. With RIGHT sides together, pin tape to armhole edge (over
sleeve) placing crease along the 3/8” (1cm) seam line,
turning under and lapping one end at side seam. Stitch. Trim
seam; clip curves, being careful not to clip tape.
English/Spanish 3
2373
4/4
5
17
16
16. Turn tape to INSIDE; press. Baste close to inner edge. On
OUTSIDE, top-stitch as basted.
5. Stitch pants front to pants back at RIGHT side seam. Stitch
LEFT side seam from lower edge to notch. Back-stitch at
notch to reinforce seam.
17. Mark length. Mark depth of hem; trim evenly. Turn facing to
OUTSIDE. Stitch across facing along hem marking. Trim
facing close to stitching. Trim garment to within 5/8" (1.5cm)
of inner edge of facing.
18
18. Turn facing to INSIDE; press, pressing up hem along
marking. Press under 1/4" (6mm) on raw edge. Stitch hem in
place starting at opening edge.
6. Apply fusible interfacing to WRONG side of yoke front and
yoke back sections following manufacturer’s directions. Stitch
yoke front to yoke back at RIGHT side seam.
19
7
6
7. With RIGHT sides together, pin yoke to upper edge of pants
matching centers and RIGHT side seam. Stitch. Trim seam.
19. On OUTSIDE, top-stitch front and neck edges 3/8” (1cm)
from finished edges. Sew buttons to LEFT front edge
opposite loops.
1
PANTS D
8. Press yoke out, pressing seam toward yoke. Stitch RIGHT
side seam of yoke facing sections. Press under 1/2” (1.3cm)
on notched edge of facing; trim to 1/4” (6mm). With RIGHT
sides together, pin yoke facing to yoke at upper edge,
matching centers and RIGHT side seams. Baste. Stitch. Trim
seam; clip curves.
8
9
STAY-STITCHING
9. To understitch press facing away from garment; press seam
toward facing. Facing side up, stitch close to seam through
facing and seam allowances.
1. Stay-stitch upper edge of pants front and pants back 1/2"
(1.3cm) from cut edges in direction of arrows.
This stitching stays in permanently and helps prevent
stretching on curved edges.
Stay-stitching will not be shown in the following illustrations.
10
2. To make darts in pants back, with RIGHT sides together, fold
the fabric through the center of the dart, bringing broken lines
and small dots together. On INSIDE, place pins at RIGHT
angles to the broken lines. Stitch the dart from wide end to
point.
TIP- To prevent a “bubble” at the point, make the last few
stitches right on the fold and leave the thread ends long
enough to tie a knot. DO NOT back-stitch at the point.
Press the dart flat along the stitching to “blend” the stitches,
then press dart toward center.
2
10. Turn facing to INSIDE having LEFT side edges even; press.
Pin pressed under edge of facing over seam, placing pins on
OUTSIDE. Lower edge of facing extends 1/8” (3mm). On
OUTSIDE, stitch in the ditch or groove of seam, catching
pressed edge of facing on INSIDE and removing pins as you
come to them. Baste LEFT side edges.
11. Press under 5/8" (1.5cm) on LEFT front opening edge and
1/2" (1.3cm) on LEFT back opening edge. Pin LEFT back
edge to zipper tape, placing pressed edge close to zipper
teeth and tab end of zipper 3/8” (1cm) below upper edge of
opening. Turn upper end of zipper tape over seam allowance.
Baste. Pin and baste LEFT front edge to zipper tape, lapping
LEFT front 1/8" (3mm) over LEFT back. Turn upper end of
zipper tape over seam allowance. Baste. Stitch as basted,
using an adjustable zipper foot. Sew a hook and eye at upper
edge when garment is finished.
11
3
3. Pin pants front to pants back at inner leg seams, matching
notches and small dots. Stitch seam, stretching back to fit.
4
INNER
LEG
SEAM
4. With RIGHT sides together, pin center seam, matching inner
leg seams and notches. Stitch. To reinforce seam, stitch
again over first stitching. Press seam open above notches.
© Copyright 2010—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
12
12. Mark length. Press up hem along marking. Mark depth of
hem; trim evenly. To EDGE FINISH the raw edge... stitch
under 1/4" (6mm) on raw edge, zig-zag, OR overlock/serge.
Slip-stitch hem in place. If you prefer to crease pants, fold leg
edges together, matching side and inner leg seam; press.
">