Mitsubishi Electric MR-B42S Refrigerator-Freezer 使用須知
पीडीएफ
दस्तावेज़
विज्ञापन
विज्ञापन
Refrigerator-Freezer 冷藏冷凍雪櫃 MODEL MR-B42S OPERATING INSTRUCTIONS 使用須知 Non-Freon Refrigerators This refrigerator uses non-Freon refrigerant (isobutane) and non-Freon foam insulation (cyclopentane). These materials are harmless to the environment, which does not affect the ozone layer and global warming. 非使用氟利昂的雪櫃 這個雪櫃使用非氟利昂冷媒 ( 異丁烷 ) 和非氟利昂發泡隔熱材料(環戊烷)。 這些物料不會對環境造成破壞,也不會 破壞臭氧層以及使全球暖化問題惡化。 R600a Function Overview Move and rotate for efficient use of space from the top to bottom shelves Revolving Shelf Shellf Refrigerator compartment Get the hard-to-reach items at the top, innermost position! Refrigerator compartment Versa compartment Ice making compartment Shelves can be rotated without Freezer compartment removing food. Pages 16 - 17 Vegetable Vegetable compartment compartment The cold a air is sterilized*1 and deodorized with the HIKARI LED and filter. You can place freshly cooked, hot food directly inside! side! The food temperature is stabilized to minimize frost and discoloration. (Freezer burn control) Versa compartment After supercool freezing, store in the soft freezing mode. Refrigerator compartment Soft Freezing HIKARI Supercool Freezing Frozen but you can cut! Pages 13 - 15 Pages 14 - 17 *1 HIKARI Active Vio deodorizer Pages 16 - 17 *1 The effect has been proven after 18 with a 12 cm2 filter, but these conditions Non-Freon Refrigerator Silent Design This refrigerator uses non-freon refrigerant and non-freon foam insulation material. Non-freon refrigerant (cyclopentane) do not deplete the ozone layer and their contribution to global warming is extremely low, An extremely low noise level of about 16 dB(A)*2. *2 According to the noise level test specified in JIS C9607 (at low speed operation). dB(A): Noise level unit. Decibel A This refrigerator is manufactured for refrigerating and freezing foods in general households. For industrial use, please use a commercial The material names are indicated on the main plastic parts to facilitate recycling. Safety Precautions 4 From Installation to Operation 6 Using Control Panel · Child safety lock · Initial settings · Reset the settings AUTO Shelf Refrigerator When you only need a little height... no problem! Freezer Raise or lower the temperature in the compartments Vegetable Fast cooling Shelves can be moved Ice up and down without removing food. Versa Refrigerator compartment FZR SOFT FZR 8 9 10 Selecting ice making modes 11 · To make ice quickly · To make crystal ice slightly faster How to switch 12 HIKARI Supercool Freezing 13 Soft Freezing Tips for Supercool Freezing 14 Page 17 How to use the refrigerator The vitamins in Delicious, crystal clear vegetables are boosted ice is made using the HIKARI LED and filter by the HIKARI LED Vegetable compartment Ice making partmentt compartment Refrigerator Compartment 16 Tips for energy saving 17 Freezer Compartment 18 Versa Compartment (Supercool Freezing Compartment) 18 Vegetable Compartment 19 Ice making Compartment (Automatic Ice Maker) 20 Making Ice / Stopping to make ice 21 Maintenance Maintaining the Automatic Ice Maker 22 HIKARI Vitamin Factory Page 19 HIKARI UV Crystal Ice Page 20 hours in a test where bacteria was sterilized in a sealed container vary from the actual operation conditions. (isobutane) and non-freon foam insulation material making them environmentally friendly substances. · Water supply pipe / Tank holder · Ice tray (Rinse it with water) · Water tank · Pipe, Water supply pump, Light-type bacteria removing / lead clean filter 23 Removing and maintaining the accessories 24 When in trouble ... What to do when ... 26 Power blackout, moving over, or not use for long time, etc. refrigerator-freezer. Specifications 27 If you think the refrigerator is in trouble, ... 28 Safety Precautions Safety Precautions Warning Installation Leave space around the refrigerator Anchor the refrigerator to a strong wall or posts protect against damage during earthquakes Leaking refrigerant can accumulate, then catch fire and explode. The refrigerator can tip over and cause injury. page 7 Tip-resistance Leave space Danger and the degree of danger caused by improper handling are categorized and described by the following indicators. Do not install the refrigerator outdoors or at places exposed to water or moisture. Failure to heed this instruction may cause poor insulation resulting in electric shock or fire. page Warning Improper handling can result in death, serious injury, etc. Improper handling can result in personal injury or damage to house, household furnishings, etc. 6 Do not wet 6 Service Call Power and power plug Do not squash the power cord at the rear of the refrigerator. Do not damage the power cord. Non-removal of plug can cause electric shock or injury. Pressing, placing heavy objects on, folding or bundling cord can cause electric shock or fire. Remove plug 4 Prohibited Do not use damaged cords, plugs, or loose sockets Do not pull on the power plug or cord to unplug it. Can cause electric shock or fire. Can cause damage to the cord, electric shock or fire. Prohibited Do not use Do not remove or insert power plug with wet hands. Dust can cause insulation failure, which may lead to fire. Can cause electric shock. Remove dust Wet hands prohibited Caution Never touch when your hand is wet In the case of malfunction or defect, immediately shutdown the refrigerator and consult the retail store at which you purchased it or a Mitsubishi Electric Maintenance Service or Customer Service representative. Cord face-down Remove power plug before changing interior light bulb or maintenance Never bring into contact or wet with water Be sure to remove the power plug from the socket Only use an outlet that meets the specified rating. Inserting plug upside-down places stress on the cord and can cause heat build-up and fire. Remove dust from power plug Be sure to follow instructions for execution 6 If the power cord is damaged, purchase a new cord from MITSUBISHI SERVICE CENTER. Make sure that the power cord is designed for this model. Never touch Never attempt to dismantle, repair or alter page Turn the power cord face-down and insert prongs to the root of plug Meaning of symbols Never do Using extension cords and plugging too many leads into a single socket can cause heat build-up or fire. If the power cord is damaged, call our MITSUBISHI SERVICE CENTER for the replacement. page Caution Use a dedicated outlet for the power supply that meets the rating specified on the rating label. (The rating label is located on the door-liner of the refrigerator compartment.) Installation and transportation Anchor the refrigerator to a strong and level floor by adjusting the adjustable supports Unstable anchoring can cause the refrigerator to move and lead to injury. page 7 Use transport hand-holds when transporting the refrigerator Holding other parts can cause injury. page Install level 26 Grip hand-holds Observe the following when opening and closing the compartment doors. · Do not open or close the compartment doors when someone else is operating or using the refrigerator. · Do not put your fingers on the top edge of the slide case door when closing it. · Use care not to pinch your foot fingers when closing the lower slide case. · Do not open or close the doors with an excessive force. (Or else, foods may fall, causing you to get injured.) · Use care not to pinch your fingers when closing the doors. Prohibited Use Do not place containers with water on top of the refrigerator Do not use electrical appliances in the refrigerator Do not place volatile inflammable objects inside the refrigerator Wetting electrical parts can cause electric shock or fire. If the refrigerant leaks and contacts the electrical appliance, it can cause explosion or fire. Benzene, cosmetics and hair dressing products can catch fire or explode. Do not wet Do not place objects on top of the refrigerator Objects may fall when doors are opened and closed and cause injury. Prohibited Do not try to hang down from the door or door handle. Do not get on the open door. Do not apply heavy load. The refrigerator may tip over and cause injury. Prohibited Do not damage the refrigerant circuit or the pipes nor mount anything with screw Items that require strict management can not be stored in household refrigerators. The refrigerant is flammable, which can cause explosion or fire. Pyrotechnic sparks from electrical contact can cause explosion or fire. Prohibited Do not store Do not place hands into the machine section of the automatic ice maker (located above the ice storage bin) Failure to heed this instruction may cause injury. Prohibited If you notice gas leakage, do not touch the refrigerator. Open windows to ventilate Do not store Do not store chemicals or scientific specimens in the refrigerator Do not place combustible sprays near the refrigerator Pyrotechnic sparks from electrical contact can cause inflammation or fire. Do not use Do not touch Do not wash with water or spill food liquids on the refrigerator Do not use the refrigerator in a barn or a garage Water and food liquids can cause electric shock or fire. Immediately wipe clean wet surfaces. Small animals could damage the electrical wiring, causing an electric shock or a fire. Ventilate Safety Precautions Warning Do not spray water Do not use When opening or closing the door, do not let the door hit a piece of furniture around Or else, the door or the parts may be broken, causing an injury. Prohibited Malfunction and long-term storage If the refrigerant circuit (piping) has been damaged, do not touch the refrigerator and open windows to let fresh air in and avoid using fire In the event of malfunction (when you detect a burning odour or other abnormality), remove the power plug from the socket and shutdown the refrigerator In case the refrigerant circuit has been damaged, please contact the retail store. Continued operation during malfunction can cause electric shock or fire. Ventilate If there is any possibility that a child is trapped in the refrigerator, pull and remove the door packing Children getting trapped in refrigerator can cause disastrous results. Remove packing Remove plug Do not attempt to dismantle, repair or alter Do not use this refrigerator when the parts of it are damaged. Can cause injury, electric shock or fire. Do not dismantle When the refrigerator is not in use for a long period, remove the power plug from the socket and open the door to dry the refrigerator If you want to dispose of the refrigerator, contact the retail store or the municipal government and hand it over to them. If not dried sufficiently, refrigerant (gas) can leak due to condenser corrosion and cause explosion or fire. Leaving it as it is allowing refrigerant to leak, may cause a fire or explosion if exposed to flame. Dry Hand it over Caution Use Do not place food inside excessively. Do not pull shelves with force. Food may fall down causing injury. Prohibited Do not touch food items or containers in the freezer compartment with wet hands Can cause frostbite. Wet hands prohibited Do not place bottles in the freezer compartment, ice making compartment or versa compartment (when set at soft freezing or freezing) The bottle may break when the liquid inside gets frozen and may cause injury. Do not eat smell discolored Food Can cause food poisoning or illness. Do not store Prohibited Do not put your hands or feet underneath the refrigerator Close the door using the door handles Steel plates, etc. can cause injury. Be careful not to catch fingers in the door when you hold it. Can cause injury. Do not touch Hold door handle 5 From Installation to Operation From Installation to Operation At least 10cm Dedicated outlet that meets the specified rating. At least 2cm Install the refrigerator. Installation area The installation area should not be exposed to direct sunlight or hot air, and should be well-ventilated to avoid diminished cooling power and to economise on the cost of electricity. It should have little humidity to prevent rusting Connect the power supply. *Connect power supply soon after installing the refrigerator. Use a dedicated outlet Use a dedicated outlet for the power supply that meets the rating specified on the rating label. (The rating label is located on the door-liner of the refrigerator compartment.) Warning Using outlets that do not meet the specified rating or plugging in too many leads into a single socket can cause heat build up or fire. It should be strong and level to prevent vibration and noise, half-shut doors, and tilted doors. Install a strong plate or board under the refrigerator if the supports easily sink into the floor. (For prevention of deformation or discoloration due to heat or weight) The refrigerator will not be damaged even if the power is supplied soon after installation. It takes a while for the refrigerator to cool, therefore supply power as soon as possible. A place away from other devices Make sure this unit is properly grounded. Electrical Connections 0REVENTIONOFTELEVISIONNOISEORIMAGE disturbance. Leave space for heat ventilation Leave at least 2cm of space on the right and left and 10cm of space between the ceiling and the top of the refrigerator to allow heat to escape from the ceiling and the sides of the refrigerator Warning Do not close the ventilation hole of the refrigerator or the crack around the refrigerator. If the refrigerant leaks, ignition or explosion may be caused. Outside of the refrigerator body gets hot. Due to heat radiation, it becomes about 50 to 60°C when starting to use or in summer. The unit should always be plugged into its own electrical outlet. This will provide the best performance and prevent electrical circuits from being overloaded and causing a fire. Make sure that the electrical outlet provides the proper voltage. Extension cords are not recommended. If your unit is installed in the high humidity location, not only ground connection but also installation of the earth leakage breaker is recommended. If the power cord is damaged, purchase a new cord from MITSUBISHI SERVICE CENTER. Make sure that the power cord is designed for this model. If the power cord is damaged, call our MITSUBISHI SERVICE CENTER for the replacement, in order to avoid a hazard. It takes time for foods to cool down after turning on the refrigerator. s0UTFOODSYETTOBECOOLEDORICECREAMAFTERTHEREFRIGERATORCOMPARTMENTSCOOL down sufficiently. s$ONOTOPENORCLOSETHEDOORSMORETHANNECESSARY7HENOPENINGADOORCLOSEIT as soon as possible. Until making first ice cubes It may take about 24 hours if it is hot around the refrigerator. The refrigerator is set to “regular ice making” at first. If you make crystal ice, change the setting. 6 page 11 Turn on the power of the refrigerator as soon as possible. Refrigerator/Front side bottom Turn each adjustable support in the arrow direction until they touch the floor. Adjustable Caster support Leg cover Adjustment and Anchoring to prevent vibration and noise, transmigration and half-shut doors Turn the adjustable supports until they touch the floor and the casters are raised from the floor Closing the doors completely Adjust the adjustable supports to install and secure the refrigerator at level. Raise the front part of the refrigerator so that you can close the doors easily. Caution Insufficiently adjusted supports can cause injury due to migration of the refrigerator. Adjusting titled doors and an uneven refrigerator Readjust the adjustable supports as shown in the figures below. The right door sags down. The left door sags down. If the installation area is not level or the refrigerator supports sink after a few days due to the weight of the food, the doors will appear lower. (Depending on the quantity of food, the food weight can exceed 100 kg.) Turn the adjustable support to the direction shown in the figures for readjustment. Right Left Raise the right side. Leg Cover The leg cover is bundled in the refrigerator compartment before shipment from the plant. From Installation to Operation The refrigerator will not be damaged even if you turn on the power immediately after the installation. How to attach leg cover Fully push in the leg cover horizontally until it comes into contact with the mating part of the refrigerator. Leg Cover Adjustable support Raise the left side. When adjustable supports are insufficient 7HENINSTALLINGTHEREFRIGERATORINA corner of a room, one of the rear legs may sink, causing the refrigerator to tilt. If it is the case, use a caster support or a sturdy board for adjustment. (Normally, the thickness of the board is 2 to 3 mm as a guideline.) Do not cause damage to refrigerant circuit (piping) / Do not attach screws. Non-freon refrigerants are flammable gas. However, it is hermetically sealed, therefore, leaking is infrequent. Warning Just in case of having damaged the refrigerant circuit. 1. Do not use electric items or fire equipments near by. 2. Open the window and ventilate the room. And then contact the retail store you have purchased from for further instructions. Rear leg Caster support or sturdy board Prepare for earthquakes Thread strong belts through the 2 handy-grip recesses on the top-rear of the refrigerator and secure them to the wall, posts or another strong area. Strong belts Warning Your refrigerator tipping over can cause injury. 7 Using Control Panel The selected The selected ice The setting of the selected compartment Supercool Freezing making compartment mode is illuminated. setting is illuminated. is displayed. Switches between compartments to be monitored. Controls temperatures in compartments. Display Using Control Panel Top The selected compartment is illuminated. Operation button Bottom The display on the screen switches as follows every time you press the button. Refrigerator, Freezer and Vegetable compartment page 10 Versa compartment page 12 In this mode, the refrigerator does not accept any button operation such as when a child plays with the buttons or presses any of them unintentionally. 8 page 13 Soft freezing Switches between ice making settings. How to make ice page 11, 21 Available for use when the versa compartment is set to soft freezing (either to “L”, “M” or “H”). Not making ice for a page 21 long time * The above shows a display example and may differ from the actual display. Other settings Child safety lock Supercool Freezing * The refrigerator accepts a compartment selection even in the child safety mode. Press The lamp and simultaneously for about 3 seconds. (until the buzzer emits “peep, peep” tone.) lights up. To cancel Same as the above operation. Fast cooling operation Ice maker cleaning (HOLD 5 SEC) Cools down foods and beverages quickly Refrigerator, Freezer and Vegetable compartment page 10 Versa compartment (Only when set to freezer) page 12 Rinses ice tray page 22 Do not press the button for a long time except when you want to select ice maker cleaning. To save energy, the lamp goes out if you do not operate the refrigerator for 30 seconds. (Yet, the refrigerator still memorizes the instructed settings.) The indication keeps lit when operating in the supercool freezing mode. The lamp lights up when you operate it but the refrigerator has not received your instruction yet. Be sure to let the lamp light up first then operate the button. The temperature control for the versa compartment is set at “Soft freezing, Medium” Supercool freezing is in operation The ice making mode for the ice making compartment is set at “Crystal” Using Control Panel Display example The versa compartment is now being displayed Example: The display indicating the versa compartment Initial settings [Initial settings after installation (procurement)] Refrigerator Choose your favorite settings. Ice Versa Freezer Temperature control to medium Regular ice making Soft freezing Temperature control to medium Temperature control to medium Not set yet Child safety lock Supercool Freezing Vegetable Temperature control to medium About door alarm Fast cooling Reset the settings The number of times of “peep, peep” sounding tells you the following conditions. The door on the refrigerator, ice making or freezer 4 times* compartment is open for more than 1 minute. Close the door. *The buzzer sounds “peep, peep” 4 times in every 1 minute after opening the door. It continues to sound if the door is open for more than 5 minutes. Check if the door is not fully closed or food is pinched (at the rear end of the packing case). Blinks while Check it at least once every month. interlocking with “peep, peep” If the buzzer keeps sounding even after tone. closing the door, call up the retail store which you purchased this refrigerator from. The operation panel blink while interlocking with the door alarm sounding. Use this function when, for example, you forget the settings. This operation brings the compartment selection, temperature control, fast cooling and supercool freezing settings back to the initial ones at the time of installation (purchase). Press and simultaneously for about 3 seconds. (until the buzzer emits “peep, peep” tone.) The temperature control for does not change. If the ice making compartment has been set to , it switches to . If set in other settings, no changes take place. If lamps on the operation panel blinks The refrigerator is in the demonstration operation when all the lamps on the display blink 3 times in a regular interval or the compartment display and temperature control display take turn to blink repeatedly. The refrigerator suspends its cooling function during this mode. Cancel the demonstration operation. page 26 9 Setting the Refrigerator, Freezer and Vegetable Compartment Raise or lower the temperature in the compartments. *Display example. Press to display the compartment you want to change the temperature control mode. Press to change the temperature control mode. Press to display the compartment you want to cool fast. The display will change at each press. The display will change at each press. The display will change at each press. The temperature control in each compartment is as follows. Compartment display Temperature control Raise or lower the temperature in the compartments / Fast cooling *Display example. Fast cooling Press and hold for 3 seconds. (Until the buzzer emits “peep, peep” tone.) is illuminated. Ends automatically in about 2 hours. is extinguished. *1 Too cool 2 to 3°C higher than “M” level 2 to 3°C higher than “M” level 2 to 3°C higher than “M” level Slightly cool 1 to 2°C higher than “M” level 1 to 2°C higher than “M” level 1 to 2°C higher than “M” level Standard Around 0 to 6°C Around -16 to -22°C Around 3 to 9°C Slightly cooler 1 to 2°C lower than “M” level 1 to 2°C lower than “M” level 0 to 1°C lower than “M” level Much cooler 2 to 3°C lower than “M” level 2 to 3°C lower than “M” level 1 to 2°C lower than “M” level and If you want Press to stop before it ends extinguished. is &ASTCOOLINGOFVERSACOMPARTMENT page 12 ()+!2)SUPERCOOLFREEZING page 13 *1: The temperatures differ from the freezing setting in the versa compartment. About the temperature control in the versa compartment page 12 *For finer temperature control page 27 *For switching the freezer to the soft freezing page 26 Temperatures in the compartments s 4HEABOVETEMPERATURESAREGUIDELINES4HETEMPERATURESMAY differ depending on the use, such as storage of foods and opening/closing the doors. s 4HETEMPERATURESINTHECOMPARTMENTSMAYTEMPORARILYRISEOR drop before or after defrosting. s The temperatures given above represent the guideline temperatures measured after reaching stabilization at the lower part of the refrigerator when the ambient temperature is 30°C and the doors closed with nothing inside. The temperatures may differ depending on the use, such as storage of foods and opening/closing the doors. 10 When to use ? Use the fast cooling mode when storing a lot of foods after buying a lot. The refrigerator cools down the foods quickly to keep them fresh. s 9OUCANUSEFASTCOOLINGWITHFOODSINSIDE s 4HETEMPERATUREREACHESTHESETTEMPERATUREAFTER FASTCOOLING s $URINGTHEFASTCOOLINGTHENOISEFROMTHEREFRIGERATOR will become higher due to high speed cooling. Setting the Ice Making Setting the Ice Making Compartment 4HEICEMAKINGCOMPARTMENTTAKESTIME OFTOHOURSTOMAKECRYSTALCLEARICE Compartment s Do not open or close the ice maker door often to make ice quickly. Selecting ice making modes To make ice quickly *Display example. Press to illuminate is extinguished, and the is illuminated. Ends automatically Press repetitively referring to the table below until the desirable ice making mode is displayed. 4HEREFRIGERATORISINMODEWHENINSTALLED (when purchased). The display will change at each press. Ice making mode can be selected from 4 types. It automatically completes ice making when: · Operating for about 9 hours or when the ice storage bin is full of ice (about 60 to 100 pieces), or · No water is left in the water tank. s During the “QCK” ice making mode, the noise from the refrigerator will become higher due to high speed operation. s )MMEDIATELYAFTERTHEINSTALLATIONITMAYTAKEMORETHAN hours to make ice even if “QCK” mode is selected. To make crystal ice slightly faster To increase the clarity of ice (Regular Select this mode when you want ice making) make a large quantity of ice. Set the ice making to (Quick Select this mode when you ice making) want to make ice quickly. Press (Crystal Select this mode when you ice making) want to make crystal clear ice. It will take more time compared to “REG” mode (about 5 to 8 hours). (Stop Select this mode when you use ice making) the compartment as a freezer. Be sure to clean the water tank and pipes to inhibit mold growth. page 22, 23 *How to make ice (supply water) page 21 . , . and Selecting ice making modes / To make ice quickly About Ice making time, Please refer “Rough standard of ice making time for one cycle” simultaneously and hold for about 3 seconds. (Until the buzzer emits “peep, peep” tone.) will light up and whichever applicable, will blink. Display of other compartments will be extinguished temporarily. Blinking Press repetitively; if you want to make crystal ice quickly, and, sto illuminate sto illuminate if you want to make clearer ice cubes. sNote that the refrigerator is set to when installed (when purchased). After a while, the buzzer emits “peep, peep” tone and blinking changes to normal lighting and after about 2 seconds the light will be extinguished. Selecting “L”, “M” or “H” will light only . The displays for other compartments return to the original ones. Rough standard of ice making time for one cycle (7 to 8 pieces) Ice making time Quick ice making 60 to 100 minutes Regular ice making 100 to 130 minutes Crystal ice making 5 to 8 hours s The ice making time differ according to the ambient temperature, conditions of usage, type of water and quantity and temperature of water in the water tank and may be longer than the above. · when the ambient temperature is low such as in winter. · when doors are opened and closed frequently. Rough standard for crystal ice making time and clarity Display L M H Ice making time Faster than About 5 to 8 Slower “M” hours than “M” Clarity 70 to 80% 80 to 90% 90% or of ice of ice more of ice (Percentage of clear area) 11 Setting the Versa Compartment (Supercool Freezing Compartment) How to switch How to switch *Display example. Difference between soft freezing and freezing s4OFREEZEMEATANDFISHINSOFT freezing for about 2 to 3 weeks. s4OSET3UPERCOOL&REEZING s4OSTOREMEATFISHANDOTHER processed foods for about 1 month. About -5°C To freeze foods soft to be cut easily Foods containing a lot of water s"OILEDVEGETABLES s,ARGEBLOCKSOFMEAT with less fat The optimum temperature to freeze foods in the soft freezing mode. You can freeze foods on a tray. Press to display Press to choose the desirable temperature control mode. . Fast cooling *With the versa compartment set to the freezing. *Display example. About -7°C About -9°C For foods difficult to freeze Foods containing a lot of salt or sugar s&OODSDIPPEDINSOYBEANSAUCEOR miso. s#ODROE To preserve foods containing a lot of salt or sugar Enjoy nice chewing. About –12°C Commercially available frozen foods or ice cream cannot be stored in the “ About -15°C ” or “ ” mode. To preserve home-made frozen foods for about 1 month To preserve commercially available frozen foods and ice cream About -18°C Freezes ice cream comfortably hard. Press Press to display . to choose . *No fast cooling for soft freezing. Press for 3 seconds. (until the buzzer emits “peep, peep” tone.) Ends automatically in about 2 hours. If you want to stop before Press it ends and is illuminated. is extinguished. is extinguished. s7HENTHEVERSACOMPARTMENTISSETATSOFTFREEZINGMODEFAST cooling will not take place. Pressing QCK will emit a buzzer sounding “peep, peep.” sDuring fast cooling, the noise from the refrigerator will become higher due to high speed cooling. *The temperatures differ from those in the freezer. The preservation period is about 1 month when the versa compartment is set to the freezer. *For fine-control of temperatures page 27 s4HETEMPERATURESINTHECOMPARTMENTSMAYTEMPORARILYRISEORDROPBEFOREORAFTERDEFROSTING sThe temperatures given above represent the guideline temperatures measured after reaching stabilization at the lower part of the refrigerator when the ambient temperature is 30°C and the doors closed with nothing inside. The temperatures may differ depending on the use, such as storage of foods and opening/closing the doors. 12 HIKARI Supercool Freezing s is illuminated in the Supercool Freezing operation. sOperating the operation button illuminates the display. sThe display is extinguished after 30 seconds of no operation. *With the versa compartment set to the soft freezing. Supercool Freezing keeps foods tasty while preventing tastes and textures from deteriorating. Use Supercool Freezing to freeze hot foods while keeping them tasty. Use Soft Freezing to preserve foods conveniently. Hot foods such as freshly cooked rice and curry Quickly freezes hot foods. ·Foods are frozen without losing moisture and taste. Freezes foods tasty while maintaining tastes and textures. Meat and fish before cooking ·Keeps the original flavor when thawing meat. ·Potatoes, bamboo shoots and broccolis keep original textures. Supercool Freezing Completed HIKARI Supercool Freezing To enjoy tasty frozen foods. No need to bother unfreezing or cutting in pieces. Use soft freezing to preserve foods. ·Although seemingly frozen, you can cut the foods to pieces with a cooking knife. *To preserve for a long time, place the foods in the freezer after freezing them in the supercool freezing mode. *Display example. Switch operation for the supercool freezing is the same for both hot and cold foods. 4HE()+!2)ISEE3ENSORCHECKSTHE food temperature to cool it automatically. Press to display Check that Check out the next page for better supercool freezing. . is displayed. If the refrigerator has been to the freezing mode, set it to soft freezing. page 12 When the temperature stabilizes (in about 2 hours), start supercool freezing. *Supercool freezing is not available in the freezing mode. Press . is illuminated. If not operating the buttons for 30 seconds, all displays except extinguished. are is illuminated (in about 3 to 12 hours). *The time differs depending on the quantity, temperature and type of food. After supercool freezing, foods are preserved in the soft freezing mode. Ends automatically If you want to stop before it ends Press to turn off . s 3UPERCOOLFREEZINGISAVAILABLEWITHTHEFOODSLEFTINSIDE s 9OUCANOPENORCLOSETHEVERSACOMPARTMENTDURINGSUPERCOOLFREEZING s )FTHEBUZZEREMITShPEEPPEEPvTONEWHENPRESSINGTHESUPERCOOLFREEZINGBUTTON 3UPERCOOLFREEZINGISAFUNCTIONONLYFORTHEVERSACOMPARTMENT)TISNOTAVAILABLEINANYCOMPARTMENTOTHERTHANTHEVERSA compartment. You cannot use the supercool freezing function if the versa compartment is set to . s )FTHEROOMSELECTIONISINANYPOSITIONOTHERTHANISNOTDISPLAYEDEVENDURINGSUPERCOOLFREEZING s 3WITCHINGTHEVERSACOMPARTMENTSETTINGTODURINGSUPERCOOLFREEZINGSUPERCOOLFREEZINGSTOPS s 4HE()+!2)ISEE3ENSOROPERATESCONTINUOUSLYFORMINUTESAFTERSTARTINGSUPERCOOLFREEZING!FTERTHATITOPERATESFORABOUTMINUTE ONCEEVERYMINUTESFORTHENEXTTOHOURS7HENTHE()+!2)ISEE3ENSORISOPERATINGYOUMIGHTHEARAOPERATINGSOUNDOFhPOONv s 4HEBLUE,%$FORTHEVERSACOMPARTMENTLIGHTSUPWHILEINTERLOCKINGWITHTHEBLUE,%$ATTHEFARENDOFTHEREFRIGERATORROOMANDTHE()+!2)ISEE3ENSOROPERATION )TDOESNOTALWAYSONWHENTHEVERSACOMPARTMENTDOORISOPEN 13 Soft freezing HIKARI Supercool Freezing What to use for preservation? HIKARI Supercool Freezing Use food wrapper around foods or rice. HIKARI Supercool Freezing and Soft Freezing Some tips for you To enjoy tasty foods again s Do not use aluminum foil and paper food wrappers. The refrigerator cannot measure the food temperatures accurately. Freeze hot foods Do not let moisture and flavor gone. No need to cool foods down. You will not forget to put foods in the refrigerator. Rice For leftover rice, wrap it up by each china bowl with food wrapper. Use soft freezing to preserve for about 2 weeks. You can unfreeze the rice balls evenly as you wish. Curry You can put hot, leftover curry in the versa compartment for supercool freezing. The refrigerator preserves the curry with potato pieces while maintaining good textures. Sauces Put freshly cooked hot sauces in an airtight container for supercool freezing. When the sauce becomes solid, cut them up to dices and put them in a plastic bag for preservation. You can take out only a necessary amount any time while saving room in the compartment. When using a shielded food container, fill it up with foods. s The refrigerator may not accurately measure the temperatures of a small quantity of food in a large container. Hot foods? Do not put foods hotter than 80°C. (Example) Freshly cooked rice: about 70°C s )TMELTSFOODS nearby or deform the container. Be careful handling hot foods that you cannot hold in bare hands. Or else, you may get burned. Meat and fish Supercool freeze meat and fish. Then, preserve them by soft freezing. page 13 You can cut up foods after soft freezing. With soft freezing, your meat or fish can be cut with a knife immediately, thereby shortening your cooking time. s Items that have been transferred from freezer to soft freezer or soft freezer to freezer should be used within 1 to 2 weeks. Blocks of meat Make each meat block to 100 to 400 grams for supercool freezing. Meat that has been stored in the freezer or was bought frozen can be transferred to the soft freezer. s $EPENDINGONITSSIZEYOURMEATSHOULD be ready to cut within 2 to 5 hours after it is transferred from the freezer. Thinly sliced meat or bacon Thinly sliced meat or bacon can be cut immediately. They will thaw while cooking or dipped in basting, during which time you can easily separate them. s 4HEYMAYNOTBEABLETOBESEPARATED immediately after they are removed. Then, leave them for a while before you separate them. Ground meat Put boiled vegetables while they are hot to cool them down in the supercool freezing mode. Potatoes and broccolis You can cool down hot potatoes and broccolis to cook croquettes and vegetables. 14 You can cut and remove the amount you want to use. Furthermore, if you cut them into small cubes, they will thaw enough in 15 to 30 minutes for you to loosen with your hands. Cutlets and cod roe Cutlets can be cooked on a low frame without taking the time to thaw them. Cod roe and other highly salted foods do not freeze and can be used immediately. The HIKARI i-see Sensor (infrared sensor) watches the food condition from the top of the versa compartment. Put foods in a manner to help the HIKARI i-see Sensor measure the temperatures accurately. and Soft Freezing Put foods at one time for supercool freezing. s Do not add foods.The refrigerator may not supercool freeze the foods. sIf you put hot foods together with foods colder than the ambient temperature, the refrigerator cools down the hot foods first. Fruit and desserts Supercool freeze various kinds of fruit to enjoy them. Use supercool freezing to freeze sweet fruit. Blend supercool frozen fruit and yogurt and milk in a blender to make an easy healthy drinks. Easy to make healthful jam and ice cream with less sugar. s %ATFRUITFROZENWITHOUTTHAWING4HEYWILLNOTBEFRESH again after thawing. s 4HEFLAVOROFFRUITKEPTINTHESOFTFREEZERFORMORETHAN 1 week may change. It is recommended to eat fruit within 2 to 3 days to best enjoy its new taste. s &REEZINGTIMEMAYVARYDEPENDINGONSUGARCONTENTOFTHE fruit, so allow one night for supercool freezing. Watermelon Make watermelon ice by cutting watermelon into bite-size pieces and supercool freeze them. Smoothie 3MOOTHIEOFAPPLEANDKIWI Cut half a peeled apple into bite-size pieces, and a peeled kiwi into 1 cm circular SLICES3UPERCOOLFREEZETHEMEACH Blend supercool frozen apple and kiwi, 250 cc of milk and honey (if you like)in a mixer until it becomes smooth. (makes 2 servings) Frozen yogurt 3UPERCOOLFREEZEACUPOFSUGARED yogurt you bought from supermarket. It becomes a fine, smooth ice cream after one night. Jam 3TRAWBERRYJAM Put a pack of strawberries (about 300 grams) in a container. Mash them fine and thoroughly. Add 60 to 100 grams of sugar (depending on the sweetness of the strawberries) and mix it with the mashed STRAWBERRIES3UPERCOOL freeze the mix. Leave the mix for one night to be a tasty strawberry jam. s 9OUCANMAKEJAMFROMASMALLAMOUNTOFFRUIT4RYIT when you have extra or leftover fruit. Where to put? Place foods for supercool freezing flat on top of other foods in the versa compartment. s If placed behind other foods, the ()+!2)ISEE3ENSORCANNOT measure the temperatures accurately. *Place hot foods near the door and away from the frozen foods. s Or else, the hot foods may come in contact with frozen foods and melt them. Others Natto and fried bean curd Natto can be mixed immediately after removal from the versa compartment. Chilled fermented soybeans can be quite tasty. You can cut the amount of fried bean curd you want to use. Items that are not suitable for Supercool Freezing or Soft Freezing HIKARI Supercool Freezing and Soft Freezing How to put foods in? s $ONOTFREEZEFOODSAGAINTHATHAVEBEENFROZENANDTHAWED4HE food quality such as flavor and texture are not guaranteed. s Foods not suitable for freezing are not good for soft freezing either. The food quality such as flavor and texture before freezing are not guaranteed. Example: Konnyaku (devil’s tongue), bean curd, milk and raw eggs s The soft freezer cannot preserve commercial ice cream or frozen foods. 3TORETHESEITEMSINTHEFREEZERCOMPARTMENT About Supercool Freezing and Soft Freezing s 3UPERCOOLFREEZINGANDSOFTFREEZINGTAKESPLACEATAPPROXIMATELY -7°C, it may take up to 24 hours for food to freeze. s Even when the refrigerator completes the supercool freezing operation and turns off the lamp, the foods may not have been completely frozen on some occasions. s Open and close compartment doors with as low frequency as possible when you add items to the compartment. s 4HESUPERCOOLFREEZINGMODEMAYNOTBEAVAILABLEORthe degree of freezing may vary depending on the type of item, cooking method, arrangement of item (folded and layered or location of item), amount, and period of storage. s Items may not freeze or may freeze too much (hard to cut with a knife) depending on content of sugar, salt and fat. s If foods get frozen hard, leave them at a room temperature for about 5 to 15 minutes. Then, you can cut them with knife. s Adjust the temperature in accordance with degree of freezing. page 12 15 Refrigerator Compartment Precautions for using the Revolving Shelf Before closing the refrigerator door, return the Revolving Shelf to its original position. s 4HETEMPERATURECONTROLINTHE REFRIGERATORCOMPARTMENTISSETTOh(v s 4HEAMBIENTTEMPERATUREIS#OR LOWER Set the temperature control in the refrigerator compartment to “M” , “LM” or “L”. When foods get frozen Two-way flexishelf Interior light Revolving Shelf 7HENADOORISOPENFORMORETHANMINUTES THEINTERIORLIGHTBLINKSTWICEAMINUTETOALERTYOU )FTHELIGHTSTAYSONCONTINUOUSLYFORMINUTES ITTURNSOFF )FTHEDOORISTHENCLOSEDTHEINTERIORLIGHTTURNS ONAGAINWHENTHEDOORISOPENED Do not hang on the Revolving Shelf. AUTO Shelf Air outlets Do not place items as they are protruding from the Revolving Shelf. Chilled egg compartment Egg Shelf Bottle pocket Refrigerator Compartment Do not place the following items on the Revolving Shelf. sStacked items that slide easily, such as glass bottles. sItems that spill easily. * Do not place items with a total weight of 10 kg or more on the Revolving Shelf. Tips for energy saving ●+EEPANAPPROPRIATESPACEBETWEEN Small item case Slide chilled case 5SETOSTOREFOODSUCHASMEAT lSHPROCESSEDFOODMINCED lSHHAMETCANDYOGHURT FOODITEMS ●#OOLHOTITEMSBEFOREPLACINGINSIDE ●$ONOTOPENTHEDOORFREQUENTLYOR FORALONGTIME Set automatically ●"ECAREFULNOTTOHAVEITEMS EGFOODPLASTICBAGANDPOWER CABLEPINCHEDBYTHEDOOR Chilled !BOUTTO# OTheRWISEFOODMAYFALLANDCAUSE INJURYORDAMAGETOAShELFORPOCKET )FFOODWITHAHIGHLEVELOFMOISTUREISPLACEDNEARTHEAIROUTLETSITMAYFREEZE If the door alarm sounds s4HETEMPERATURECANNOTBE SETWITHTHECONTROLPANEL s$ONOTPLACEFOODTHAT FREEZESEASILY Page 28 Page 9 Wrap food that have strong odors thoroughly before storage 16 Food that transfers odors easily Food to which odors are easily transferred Rakkyo, dried fish, natto, miso, beef, takuan, sardines, kimchi, jiaozi, etc. Puddings, ice cream, potato salad, tofu, rice, bread, milk, cake, ice, etc. s!SLIGHTODORMAYREMAIN s!SLIGHTODORMAYREMAIN You can move the shelves and pockets Do not leave food hanging over shelves or pockets. Do not place glass bottles that cannot fit all the way to the bottom at the front of the bottle pocket. heBOTTLEMAYkeePADOORAjAROR T THEBOTTLEMAYBREAK Adjustable pocket (large) Revolving Shelf 1 Slide the left and right levers to the side to release them. 2 Rotate slowly while holding the edge of the tray. (The tray can be turned in both directions, to the left or the right.) 2 Do not attach a case that you purchased separately onto the outside of a pocket. Adjustable pocket (medium) Blue LED "ACTERIAANDODORS AREREMOVED WITH()+!2) POWER )FTHELIGHTSTAYS ONCONTINUOUSLY FORMINUTES ITTURNSOFF )TMAYKEEPADOORAJARANDREDUCE THECOOLINGPERFORMANCEORFOOD MAYFALLANDCAUSEANINJURYOR DAMAGETOACASEORLID 1 1 After operating the shelf, return it to its original position by following the procedure in reverse. Then, set the left and right levers to the lock position to fix the shelf. Removing and installing the Revolving Shelf Page 24 AUTO Shelf Move the lever to the left or right to adjust the space between the shelves. Do not close the door while food is in front of the slide chilled case or the small item case. down up If the AUTO Shelf disengages, push it back into position from above. Removing and installing the AUTO Shelf Fully stow away the cases. Two-way flexishelf 1 The upper side section has 3 adjustable positions and, the lower side section, 2 adjustable positions. Halve the shelf width to store tall objects 1 2 3 )FFOODFREEZESINTHEFOLLOWINGKINDS OFSITUATIONSSETTHEREFRIGERATOR COMPARTMENTTEMPERATURETOh-v h,-vORh,v s7HENTHEREFRIGERATORCOMPARTMENT TEMPERATUREISSETTOh(v s)NWINTERORATOTHERTIMESWHENTHE SURROUNDINGTEMPERATUREIS#ORLESS Page 10 !LONGLIFE,%$ISUSEDASTHEINTERIOR LIGHTSOUSUALLYREPLACEMENTISNOT REQUIRED 2 (Two) Adjustable pockets As a wide shelf (One) Note Page 24 1 2 Refrigerator Compartment Tips for energy saving Adjustable pocket (small) (You can also remove them) Removing the pockets Page 25 17 Versa Compartment Freezer Compartment Door alarm page (Supercool Freezing Compartment) 9 If the door is left open for more than 1 minute, an alarm will be emitted to call attention. (Refrigerator compartment, ice making compartment and freezer compartment.) Prevents wasteful leakage of cool air and reduces wasteful power consumption. Check if the door is not fully closed or food is pinched (at the rear end of the packing and case). *Check it at least once every month. The LEDs on the operation panel interlocking with the door alarm sounds blink to tell the event. HIKARI i-see Sensor (Infrared sensor, Blue LED) Senses positions and temperatures of foods. Aluminum tray Food is cooled quickly due to pre-cooled tray. Freezing case (top) Versa case Freezer Compartment / Versa Compartment 18 Do not pile up foods higher than the versa case. Or else; Food may be damaged. Food may melt. The door may not shut completely. Freezing case (bottom) Storing foods Do not put a tall food in the freezing case The food may be spoiled or the freezing case may be damaged. The door does not close. Freezing to your taste Difference between soft freezing and freezing page 12 Soft freezing To freeze meat and fish in soft freezing for about 2 to 3 weeks. Supercool freezing foods. Freezing To store meat, fish and other processed foods for about 1 month. Vegetable Compartment LEDs (ceiling area) Do not disassemble or spray water on the LEDs. Water penetration may cause malfunction. As long-life LEDs are used, normally no replacement is necessary. Slide case Vegetable case 2L PET bottles can also be stored. Gift of light! A vitamin factory LEDs are always on Vegetable Compartment Do not place tall objects under the slide case. Tall objects may cause damage to food or the slide case. If the slide case was removed and not used, it may cause the vegetable compartment to get dry. The vegetable compartment door does not shut completely. Vegetables and fruits stay fresh in a plastic wrap. Vegetables stay alive even after harvest. Under a gift of light, they increase nutrients themselves. There are no such foods as vegetables, fruit, beverages and seasonings that cannot be stored under the LED light. Simply store them in the usual manner. Even with poor light, vegetables increase nutrients. Therefore there is no need to remove fresh produce from its packing unless the packing shuts out the light. Vegetable nutrients will not continue to increase forever. The storage stability will depend on the freshness when bought. Please use the vegetables as fresh as they should be. The vegetable compartment has high humidity, therefore the bottom of each case may become cloudy or condensation may form when a large amount of leafy vegetables is placed in the vegetable compartment. If condensation collects in the bottom of a case, it will cause the case to become dirty, therefore wipe the case with a dry piece of cloth. 19 Ice making Compartment (Automatic Ice Maker) Door alarm page Your first batch of ice Discard the first 2-3 batches of ice you make or ice that is made after more than 1 week of nonuse (about 20 cubes). This ice often has bad odour or dust on it. 9 )FTHEDOORISLEFTOPENFORMORETHAN MINUTEANALARMWILLBEEMITTEDTOCALL ATTENTION2EFRIGERATORCOMPARTMENT ICEMAKINGCOMPARTMENTANDFREEZER COMPARTMENT 0REVENTSWASTEFULLEAKAGEOFCOOLAIRAND REDUCESWASTEFULPOWERCONSUMPTION 4HE,%$SONTHEOPERATIONPANEL INTERLOCKINGWITHTHEDOORALARMSOUNDS BLINKTOTELLTHEEVENT Water supply port cap Water tank lid Pipe Water supply pump Light-type bacteria removing filter with Plumbum-removal function Water tank (app. 1.2L) V-LED lamp "RINGLIGHTTOLIGHTTYPEBACTERIAREMOVING FILTERTOPREVENTTHEBACTERIAFROMBEINGBRED INTHEWATERTANK Water supply pipe The V-LED lamp lights up Ice tray sWHENTHEDOORONTHEREFRIGERATORORTHEICE MAKINGCOMPARTMENTISOPEN4HE6,%$ LAMPGOESOUTINMINUTESAFTEROPENING THEDOOR sBEFOREANDAFTERSUPPLYINGWATERINTOTHE ICEMAKINGTRAY #ANNOTBEREMOVED Soundproof mat 2EDUCESTHESOUNDOFICE DROPPINGINTOTHESTORAGE BIN$ONOTDISCARDIT Ice making Compartment Ice storage box s 4HEAUTOMATICICEMAKER MUSTBECLEANEDREGULARLY page Ice server 22 Notes for ice making Please do not put anything deep inside the ice storage bin. Door Ice server Ice storage bin Ice level sensor lever (Detects the ice storage level) Make the ice flat. s 7HENSTORINGFOODITEMSINTHEICESTORAGEBINTHEY MUSTNOTBEHIGHERTHANTHETOPOFTHEBIN4HISCAN CAUSEAMALFUNCTIONORPREVENTTHEDOORFROMCLOSING s 4HEICELEVELSENSORLEVERWILLDETECTTHEICESTORAGE AUTOMATICALLYANDWILLSTOPICEMAKINGWHENIT REACHESACERTAINAMOUNTAPPTOPCS)NORDER TODETECTTHEICELEVELCORRECTLYPLEASEMAKETHEICEFLAT ANDPUTTHEICESERVERINTHEFRONTOFTHEICESTORAGEBIN 4HEAUTOMATICICEMAKERCOULDBEDAMAGEDIFIT CONTACTSANOBJECT 20 Do not place liquids other than water, such as hot water, juice, green tea or soft drinks, in the water tank. (Heat resisting temperature, app. 60°C) 0LACINGLIQUIDOTHERTHANWATERMAYCAUSE DAMAGETOTHEAUTOMATICICEMAKERORWATERSUPPLYPUMP Do not fill the water tank higher than the full-level mark. &ILLINGTHEWATERTANKWITHAKETTLEWHILEITISSTILL INTHETANKHOLDERORFILLINGITHIGHERTHANTHE FULLLEVELMARKMAYCAUSEhCONNECTEDvICETOFORM Ice made of water containing much mineral such as mineral water might cause white sediment (white crystal). 7HENTHEICEMELTSINTOWATERITMAYAPPEARFIBROUS4HISWHITE SEDIMENTISACRYSTALOFMINERALINGREDIENTSMAKINGNOHARM If some pieces of ice are stored for a long time, they will be stuck or become smaller. on the control panel. When not used for a long period of time , page or 11 s )NITIALSETTINGOFTHEICEMAKINGCOMPARTMENTAT INSTALLATIONIS 4HEDISPLAYONTHESCREENSWITCHESEVERYTIMEYOUPRESSTHEBUTTON Check the amount of water remaining in the water tank. s /PENTHEDOORTOTHEREFRIGERATOR COMPARTMENTANDCHECKTHELEVEL FROMABOVETHETANK Ice making Compartment $ISCARDALLTHEICEANDWATERFROMTHEICETRAYINTHEICE STORAGEBINTOEMPTYTHEICETRAY Remove the water tank and close the ice making compartment door. Ice making compartment Press Water tank for about 5 seconds. (until the buzzer emits “peep, peep” tone.) Water tank Remove the water tank. Remove the water supply port cap and fill the tank with water. WARNING-Fill with potable water only. s4HEDISPLAYEITHEROROFICE MAKINGCOMPARTMENTWILLBLINKFORABOUTMINUTE 4HEWATERANDICEWILLEMPTYFROMTHEICETRAY s!FTERTHEBLINKINGSTOPSTHEORIGINALDISPLAYWILLRETURN Remove the ice storage bin and discard the water and ice. Ice storage bin s $ONOTDISCARDTHESOUNDPROOFMAT Up to the full-level mark Close the water tank cover and return it to the original position by holding it horizontally. s 4IPPINGTHETANKWILLCAUSEWATERSPILLAGE s )FTHEWATERTANKDOESNOTFITPROPERLYINPLACEICEWILL NOTBEMADE )NADDITIONITCANCAUSETHEWATERTANKTOFREEZE #HECKTHATTHEREISNOFOREIGNMATERIAL INTHETANKHOLDERORWATERSUPPLYPIPE page 22 Set the ice making compartment to . page 11 Wash the water tank (water pump, pipe, and light-type bacteria removing / lead clean filter), water supply pipe, ice storage bin, and soundproof mat with water. Dry them carefully and reinstall the parts. s 4ORESTARTTHEICEMAKERSWITCHTHEICEMAKINGSETTING page 11 Put the water tank back to its original position. Ice shapes About Crystal Ice s 4HESHAPEOFICEISTRAPEZOIDBUT SOMEWHATFLATANDUNEVEN s 4HESIZEOFICEMADEFORONETIMEMAYVARYWITHTHEWATER AMOUNTINTHEWATERTANK s /NEBATCHOFICEISPIECES s )FTHEWATERTANKISFILLEDABOVETHEFULLLEVEL MARKTHEWATERCHANNELSINTHEICETRAYWILL FREEZECAUSINGPIECESOFICETOSTICK TOGETHERANDBUMPYICE s )FSOMEPIECESOFICESTOREDLONGTIMETHEY WILLBESTUCKORBECOMESMALLER4HIS PHENOMENONISCALLEDhSUBLIMATIONv s 4HEQUICKLYMADEICEMAYBECRACKEDORSPLITDUETOFASTFREEZING s 5SECARETOAVOIDFINGERINJURIESWHENSEPARATINGICECUBES s4HEREMAYBEWHITESEDIMENTWHITECRYSTALORBUBBLES INSIDETHEICECUBE s)NCASESBELOWMAYCAUSECLEARICEINTOSUCHWHITE SEDIMENTICE q 7HENTHEMODEHASBEENCHANGEDFROM h2%'2EGULARh1#+1UICKvh34/03TOPvTO h#2,#RYSTALv )TISSETATMODEATTHETIMEOFINSTALLATION q )CEMADEOFWATERCONTAININGMUCHMINERAL 4HISWHITESEDIMENTISACRYSTALOFMINERALINGREDIENTS q 7HENSURROUNDINGTEMPERATURESTATUSOFUSEHAVE CHANGED q 7HENPIECESOFICEARESTOREDLONGTIMEINTHEICE STORAGEBIN &ROSTWILLCOVERTHEICE)FITISPUTINTOWATERTHEFROST WILLDISSOLVE Making Ice and select )TTAKESTIMETOMAKECRYSTALCLEARICE When you want to change the clarity of the ice or the ice making time operation page 11 Stopping to make ice Making Ice Press Clear ice is made slowly to increase the clarity of the ice cubes. 21 Maintaining the Automatic Ice Maker Cleaning once a month Water supply pipe / Tank holder Water Pull out the water supply pipe. supply pipe Wipe the tank holder with clean cloth. s Do not let water flow into the tank holder. Or else, it may cause malfunction. Tank holder Separate pieces and wash with water. s Twist on the aluminum pipe to replace it. *The water supply pipe may be white due to minerals or chlorine, but this is not abnormal. Wash the pipe and continue using it. Aluminum pipe Packing Water supply pipe Side A Reverse the steps to replace the pipe s Replace the water supply pipe. Make sure that sides A and B fit flush against each other. Otherwise, the ice maker may malfunction if the pipe is not installed properly. Make sure that no foreign object is found between the water supply pipe and the pipe junction. s Improper fitting or any foreign object will produce a clearance between the pipe and the pipe junction to cause freezing of the water tank. Side B Pipe junction To be horizontal Pipe Water tank Be careful not to pinch any foreign object. Tank holder (On the refrigerator body) Water supply pipe Cleaning once a week Cleaning once a month Ice tray (Rinse it with water) Maintaining the Automatic Ice Maker 22 Cleaning the ice tray using water from the water tank Remove ice from the ice storage bin and close the ice making compartment door. Fill the water tank with water and set it in place. Press Remove ice Water tank Remove the lid and wash with water. (the tank can withstand up to approximately 60°C) on the control panel and hold for about 5 seconds. (Until the buzzer emits “peep, peep” tone.) s The display ( , , , or )of the ice making compartment will blink (for about 1 minute ). (The ice tray will be cleaned by the water from the water tank.) Repeat step 2 to 3 times. Remove the ice storage bin and discard the water and ice. s Do not discard the two-layer soundproof mat. Ice storage bin *If the water tank is prone to get moldy due to the nature of water, clean the water tank 2 to 3 times a week. Be sure to read all instructions for detergents, bleach and other cleaning products you use to clean the water tank and lid. Regular cleaning produces clean and delicious ice. Regular cleaning prevents water stains, molding, etc. Cleaning once a month Pipe, Water supply pump, Light-type bacteria removing / lead clean filter Pull out the pipe. Disassemble and wash the Twist the water supply parts with water. pump to remove it. Pipe Light-type bacteria removing / lead clean filter Cap Normally, the light-type bacteria removing / lead clean filter need not be replaced. However, replace it in the following conditions: · When the filter is clogged by passing something other than water through the filter · When the filter is broken · When the filter is moldy In such cases, contact the retail store at which you purchased this refrigerator from. *If the water tank is prone to get moldy due to the nature of water, clean the water tank 2 to 3 times a week. Impeller tab While pushing the tab downward with your finger, pull the cover off. Steps to bring the water supply pump and pipe back to the original position Assemble the water supply pump hook (C)(step ) onto the water supply pump tab (D)(step ). *Make sure that the impeller is in the water supply pump. Fit the filter cover’s tab D Align the marks on the pipe and the water tank. mark Pipe C Rotate Connect the pipe with the water B Rotate the water supply pump (step ) to install it securely and correctly on the water supply tank. supply pump. *Make sure that no foreign object is found between the water supply pipe and the pipe junction. A Rotate Install the impeller into the water supply pump. Pipe junction Water supply pump Maintaining the Automatic Ice Maker (A) and hook (B) into the assembly made in step above. Improper reassembling might cause failed ice making or increased noise. Check the following. Install the pipe Fit the filter into the Rotate the cap and catch the cap cap. Do not use kitchen detergent benzene, bleach or other cleaning products to clean the light-type bacteria removing / lead clean filter. s The products above give ice odors. Cover Water supply pump The impeller is magnetic. Wash carefully to remove all foreign objects. Reverse procedure to build up 23 Removing and maintaining the accessories Before you start Maintenance and Cleaning Remove the power plug from the socket. Warning Failure to remove the plug may result in electric shock. Wait at least 10 minutes before you replace the power plug. The refrigerator will not operate if the plug is replaced immediately after it is removed. sWipe the accessories clean with a soft piece of cloth wet with slightly warm water or remove them to wash with water. sFor deposits sticking hard, wet a piece of cloth with dishwashing agent diluted with water and wipe off the deposits. Then wipe out with a piece of cloth wet with water. Be sure to wipe off all oily deposits. Oily deposits, if left unattended, can cause plastic parts to break. Note Do not use an alkaline- or alkalescent-base kitchen detergent, polishing compound, a powder detergent, alcohol, benzene, paint thinner, petroleum, acid, hard brush or hot or boiled water. They will cause damage to plastic parts (door handles, cap, cases, etc.) and coating on the surfaces such as the doors. Revolving Shelf Shelf removal Shelf installation 1Set the left and right levers 1Make sure that the levers are in to the “Lock” position. the “Lock” position. Removing and maintaining the accessories Lever Lever Lever Lever 2Hold the front of the Revolving Shelf with both hands, and while slightly lifting up the rear, push the Revolving Shelf to the rear. (Guide the rear of the shelf to get on the left and right rails.) 2Place the Revolving Shelf in the refrigerator, put it on the left and right rails, and pass it on the rails to the rear. 3While passing the Revolving Shelf through 3Lift the front of the Revolving Shelf, and remove from the refrigerator. (Pass it on the top of the left and right rails.) the grooves of the left and right rails and pulling it to the front, lower the rear of the Revolving Shelf. (When pulling the Revolving Shelf to the front, make sure that it stops in the grooves of the rails.) Tray removal 1Set the lever to the “Lock” position. 2Hold the stopper knob in the middle of the Revolving Shelf, and remove the stopper by turning it in the direction of the arrow. 3Insert your hand from the center of the Revolving Shelf, and lift up the tray. *There is a risk of the tray falling.Move it slowly. 4There is a risk of the tray falling.Move it slowly. Stopper When installing the tray, position the tray in the direction shown in the figure. Installing in other directions will result in incorrect installation, and the part may fall out. AUTO Shelf (Do not disassemble the AUTO Shelf, or use chemicals such as grease to clean it. Doing so may cause a malfunction.) Shelf removal Shelf installation 1Move the lever to the right end. 1Make sure that the lever is on the right side. Tray removal 1Push up the 3 tabs on the rear of the tray with your finger. 2Make sure that the 4 metal stoppers are fitted, 2Strongly push up each support, one by one. (4 locations.) (A clicking sound is made when the support disengages.) If the supports are firmly set and difficult to disengage, tilt the inner tabs to the inner side. 3Remove from the refrigerator. and place the shelf lightly so that the 4 supports are aligned with the 4 metal stoppers. 2Lift up the rear of the tray until the 3 front 3Push in each of the 4 supports in turn from above. (A clicking sound is made.) tabs and the 2 side tabs disengage. *There is a risk of the tray falling. Move it slowly. 1 4Move the lever to the left and right and check that the AUTO Shelf is kept level when moved up and down. (If the shelf is not kept level, remove the AUTO Shelf and repeat steps 1 to 4) 3Pull out with both hands. Two-way flexishelf Push in and lift up. 24 2 Reverse removal procedures to reinstall accessories. Periodically and after maintenance The rear of the refrigerator and the floor 1Remove the leg cover from the refrigerator. 2Turn the adjustable supports to lift them from the floor and move the refrigerator off the wall. Use protective materials so as not to scratch the floor. 3Wipe away all dust and soil from the rear of the refrigerator, the wall and the Soot, dirt floor. Wipe them clean. Air circulation can cause dust to and dust collect at the rear of and on the floor under the refrigerator, creating black soiled areas. Clean the area periodically as it also contributes to energy saving. 4Check the floor for a sign of water leaks from the refrigerator. Inspect the power cord, plug and outlet. Check the following periodically to ensure safety. 1Pull out the power plug from the power outlet and check the power plug. · Is the power cord or plug free from damage or abnormal heat buildup? 2Remove dust from the power plug and around. Clean it with a dry, clean piece of cloth. 3Put the power plug securely into the power outlet. Warning Damaged power cords or plugs, and dust collected on plugs can cause electric shock or fire. Caution Do not put your hands underneath the refrigerator. Doing so can cause injury. Slide chilled case and small item case 2 2 1 1 Adjustable pockets and bottle pockets 1 2 1 2 1Lift up the left and right alternately. (The pockets are firmly installed.) 2Pull out to the front. When installing ˙ Make sure that the pockets are securely set. (Incorrect setting may cause a pocket to disengage and fall out, causing an injury.) Ice making and versa compartments 1Fully pull out the door. 2Lift out to the front. Drip gutters Removing and maintaining the accessories 1Fully pull out. 2Lift out to the front. Wipe off any dirt, dripping or condensation. 2 1 Evaporating dish 1Push in the left and right sides alternately and pull the tray towards you to remove it. 2Hold the tray with both hands and pull it out carefully. Drip gutters Freezer and vegetable compartments Freezer compartment: Freezing case (upper) Vegetable compartment: 2 Slide case 1Fully pull out. 2Lift out to the front. Freezer compartment: Freezing case (lower) Vegetable compartment: Vegetable case 1 3Pull out while slightly lifting up the door, and then tilt. 4Lift out to the front. 4 3 25 What to do when... when Follow the instructions below Electric power goes out s2EFRAINFROMFREQUENTLYOPENINGANDCLOSINGTHEREFRIGERATORDOORSANDAVOIDSTORINGADDITIONALITEMS s3ETTINGFORMODESOTHERTHANTEMPERATUREMAYCHANGE0LEASECHECK#HILD,OCK%NERGY3AVING&AST#OOLINGETC To move the refrigerator or to change the direction 1Lift adjustable supports page 7 2Move it in forward and backward directions The unit will not be used for a long period of time 1Clean the automatic ice maker. page 22 2After removing the power plug from the outlet, clean the interior of the unit. Leave the doors open for 2 to 3 days to sufficiently dry the interior of the unit. Transporting the unit $RAGGINGITINDIRECTIONSOTHERTHANTHELONGITUDINALFORWARDANDBACKWARDDIRECTIONSMAYCAUSEDAMAGETOTHEFLOOR 3Make sure to place a cloth for floor protection underneath the caster and rear support before changing directions. *&AILURETOSUFFICIENTLYDRYTHEINTERIOROFTHEUNITCANCAUSEMOLDINGODOURSANDREFRIGERANTGASLEAKAGEDUETOCORROSIONOFTHECONDENSER 1Discard the water and ice in the water tank and the ice tray. 2Wear the protector such as work-gloves. 3Remove the leg cover and lift up the adjustable support. 4Pull out the power supply plug. 5Throw away water from the evaporating dish. page 24 6Gently transport the unit with 2 or more people, gripping the hand-holds on the lower-front interior and the upper-rear of the unit. page s$ONOTLAYTHEUNITONITSSIDEDOINGSOCANCAUSEMALFUNCTIONOFTHE COMPRESSOR 21 Front Lower interior Upper part of back side Warning It uses flammable refrigerant, do not damage the refrigerant circuit. If the gas leaks, ignition or explosion may be caused. 1Press To set the freezer to low temperature freezing repeatedly until the lamp lights up. The “FZR” lamp blinks 2Press and simultaneously for about about every 3 seconds. (until the buzzer emits “peep, peep” tone.) 10 seconds. 3Press to set the temperature control to . To cancel Set the temperature control display to any level other than step 2 above. or follow *3ETTHETEMPERATURECONTROLTOTHEFINEADJUSTMENTMODEANDSETTHETEMPERATURECONTROLOFTHEFREEZERTO 4HENTHEREFRIGERATORSETSTHEFREEZERTEMPERATURESLIGHTLYLOWER What to do when ... All indicators blink 3 times in a constant interval even though no button has been pressed. Or, the compartment display and temperature control display on the control panel blink in turn repetitively. (In the demonstration operation mode) s4HEREFRIGERATORSUSPENDSITSCOOLINGFUNCTIONDURINGTHISMODE0LEASECONTACTTHE RETAILSTOREATWHICHYOUPURCHASEDITFROMORRESETTHEDEMONSTRATIONOPERATIONBYTHE FOLLOWINGRESETTINGMETHOD How to cancel demonstration operation 1Keep the refrigerator door open. 2Press two times. 3Press , and simultaneously for about 5 seconds. 4Check that display lamps stop blinking in 1 minute. 4HEDEMONSTRATIONOPERATIONHASNOTBEENCANCELEDIFTHELAMPSREMAINBLINKING If mark is blinking rapidly (about 5 times per second) Or if the alarm cannot be turned off. 26 Contact the retail store at which you purchased it or MITSUBISHI SERVICE CENTER s0RESSINGh)#%3%,%#4vANDHOLDINGFORABOUTSECONDSWILLSTOPTHEALARMIFITKEEPS SOUNDING(OWEVERASITISNECESSARYTOPERFORMINSPECTIONPLEASECONTACTTHERETAIL STOREATWHICHYOUPURCHASEDITOR-)435")3()3%26)#%#%.4%2 You can set fine adjustment mode for the refrigerator, freezer or versa (only when “FZR” is selected) compartments. Refrigerator and Versa compartment freezer compartment (in freezing mode) page 10 page 12 App. 0.3°C lower App. 0.6°C lower than “L” than “L” Selecting fine adjustment mode If you want to select more precise temperature control mode (Fine adjustment mode) App. –12°C Low mode s)NTHEFINETEMPERATUREFINEADJUSTMENTMODETHELAMPOFTHE SELECTEDCOMPARTMENTBLINKSABOUTEVERYSECONDS Press and simultaneously and hold for about 3 seconds. App. 0.6°C lower App. 1.2°C lower than “L” than “L” (Until the buzzer emits “peep, peep” tone.) Selecting “L” and App. 1.2°C higher than “M” “M” page 10 To cancel Same as the above operation. App. 0.3°C higher than “M” Performing fine adjustment 1Press to display the compartment you want to make fine adjustment. Medium mode App. –15°C 10 page page 12 App. 0.3°C lower App. 0.6°C lower than “M” than “M” 2Press repetitively to make fine adjustment. Selecting “M” and App. 1.2°C lower page 10 “H” than “M” %X7HENTHEREFRIGERATORCOMPARTMENT ISSET#LOWERTHANh,v “H” blinks “REF” blinks every 10 seconds. App. 0.6°C higher than “M” App. 0.6°C higher than “H” App. 1.8°C lower than “M” App. 0.3°C higher than “H” App. 2.4°C lower than “M” App. –18°C High mode *4HEDATAONTHERIGHTSHOWSONLYROUGHSTANDARD4HETEMPERATURE page 12 .OTE page 10 MAYVARYACCORDINGTOTHEUSAGECONDITIONSSUCHASHOWFOODSARE STOREDANDOPENINGCLOSINGFREQUENCYOFTHEREFRIGERATORDOOR .OTE7HENTHEFREEZERISSETTOTHEREFRIGERATORSETSTHEFREEZERTEMPERATURESOMEWHATLOWERINTHEFINE TEMPERATUREADJUSTMENTMODETHANINANYOTHERMODE Specifications Accessories Units Model MR-B42S Refrigerator Compartment Revolving shelf 1 Auto-Shelf 1 Two-way flexishelf 1 Slide chilled case 1 Lid of slide chilled case 1 Water tank (with light-type bacteria removing 1 filter with plumbum-removal function.) Freezer Ice Making Versa Vegetable Compartment Compartment Compartment Compartment Adjustable pocket (large) 1 Adjustable pocket (small) 2 Small item case 1 Free egg shelf 1 Bottle pocket 1 Ice storage bin 1 Soundproof mat 1 Ice server 1 Versa case 1 Aluminum tray 1 Freezing case (top) 1 Freezing case (bottom) 1 Vegetable case 1 Slide case 1 Evaporating dish 1 Leg cover 1 Specifications This appliance is designed for use in Hong Kong only and cannot be used in any other country. No servicing is available outside of Hong Kong. 27 If you think the refrigerator is in trouble, ... Frequently asked questions at the beginning of use or in summer The refrigerator does not cool at all! The control panel is extinguished! sAt the beginning, it takes time to cool down. It may take up to 24 hours as a guideline to cool down sufficiently in summer. s Are the display lamps on the operation panel blinking? Demonstration operation: page 26 s Did you put the power plug correctly into the power outlet? Is the circuit breaker not tripped? s The display illumination will extinguish after 30 seconds if no button is pressed for energy saving purpose and it is not an abnormal phenomenon. page 9 The outer walls heat up! s Immediately after installation or during summer time, the outside temperature may become high (approximately 50 to 60°C). It is because the refrigerator is attached with heat release / anti-condensation pipe on the sides and ceiling. These are necessary for cooling and are not considered as abnormal. page 6 s4HEHEATRELEASINGFANATTHEBOTTOMOFTHE refrigerator blows out hot air. When Cannot be cooled well Not much ice cubes can be made Ice melts If you think the refrigerator is in trouble, ... 28 About use and setting Check the following See if the selected temperature control mode for the compartment that is not cooling enough is “L”. Have you just begun using the unit? Have you impeded heat ventilation due to no space around the refrigerator, placed it in direct sunlight, etc.? Anything obstructing the cool air flow? Or is the door being opened frequently or left ajar? Have you just begun using the unit? Cannot make ice at all Water in the tank stays at the same level Takes time to make ice Are the water supply pump and pipe set properly in the water tank? Is the water supply pipe set properly in the tank holder? Have you left food or the ice server laying in the ice storage bin? Is the ice making compartment set to “ STOP”? Is the ice making compartment set to “CRL ”? Is there enough water in the water tank? Is the refrigerator tilted? You are concerned by strong odors from food or ice! s Do you clean the water supply tank once every week? page 22 s Have you placed any items with strong odors inside the unit without covering them with plastic wrap? page 17 Solutions and reasons Change setting to “M” or “H”. It sometimes takes 4-5 hours for unit to cool and up to 24 hours for ice to make in the summer. Check that installation was properly executed. page 6 Check that the unit is not excessively packed with food items and that the doors are not ajar. page 17 It sometimes takes 4-5 hours for unit to cool and up to 24 hours for ice to make in the summer. In particular, check that the outlet of the pipe in the tank is securely installed to the tank. page 23 Check the installation. page 22 Assume that there is sufficient ice in the storage bin. Remove foods, etc. from the storage bin. Level out the ice evenly in the storage bin. Select either “REG”, “QCK” or “CRL” mode. “CRL” takes longer time to be made than usual ice. (approx 5-8 hours) Sometimes there are few pieces of ice in a batch. page 21 Items in compartments other than the freezer compartment begin to freeze See if “H” is selected for the temperature control mode. Have you placed items with high water content in the back of the unit? Is surrounding air temperature less than 5ºC? Change setting to “M”. Keep in mind that temperature temporarily drops during “QUICK” mode. Please place water-containing foods, such as tofu, vegetables and fruits, and beverages at the front side. Set refrigerator compartment and vegetable compartment to “L” to prevent freezing. Items in the versa compartment begin to melt. Has the temperature just been adjusted or have you just begun using the unit? Are the items on top packed too tightly? Is hot foodstuff in contact with the frozen foods? Have you pressed the [SUPERCOOL] button after placing the hot food? Do you not preserve ice cream or frozen foods in the “FRZ, L” or “FRZ, M” mode? It takes some time for the unit to cool. Wait at least 30 minutes before placing foods in the versa compartment or use fast cooling. Place the food items so that the cool airflow can flow above the items. Frozen food may melt when it comes into contact with hot foods. Press the [SUPERCOOL] button when you place hot foods. The food temperature comes down quickly. Set the temperature control to “FRZ, H”. If the situation does not correct or improve even after you check the following, immediately contact a representative of the retail store where your bought the refrigerator. Check the following Solutions and reasons Temperature cannot be adjusted Is Unable to supercool freezing (The lamp is not illuminated.) Check if the compartment display indicates “VR” and the temperature control shows “SOFT FZR”. First, set the versa compartment to the soft freezing. Then, press the[SUPERCOOL] button. Note that supercool freezing is available only when the versa compartment is set to the soft freezing. page 13 Have you pressed the [SUPERCOOL] button? Press the [SUPERCOOL] button. Check that the display shows the supercool freezing mode. The HIKARI i-see Sensor measures the temperature of the foods. Be sure to place the foods you wish to supercool freeze side by side at the top of page 15 other foods in the versa compartment. After switching to the “SOFT FZR” mode, wait for about 2 hours until the temperature inside the versa compartment page 13 stabilized. Then, supercool freeze the foods. displayed? page Foods are not tasty even after supercool freezing. Have you placed the foods you wish to supercool freeze on top of other foods in the versa compartment without pilling or folding over? Dew drops get accumulated on the outside or inside the refrigerator. Frost gets accumulated in the freezer compartment. Water drips onto the floor. Do you open the door frequently or is the door ajar? The door is easy to open The door will not close Does any food come in contact with the refrigerator door? Are too many foods stored in the refrigerator? Is any food dropped into the back side of the sliding door, or is the power cable placed between the unit and the door? Is the unit installed properly? Are the adjustable supports right on the floor? The door alarm sounds. Ice is dented, comes out cloudy small melts The water tank or the water supply pipe freezes The water tank and water supply pipe become warm Your television picks up noise Noise is loud the unit makes disturbing sounds the following sounds are normal The blue LED in the versa compartment is not illuminated. Cancel the child lock setting. Have you just switched the versa compartment to the “SOFT FZR” mode? Is it a rainy or highly humid time of year? See pages 9 and 26 for the door alarm details. Refer to page 21 regarding shape and clarity of the ice. Is the pipe securely attached to the water tank? Is there any foreign object in the pipe or pipe joint? Is any food or plastic dropped into the back side of the case in the ice making or freezer compartment? 8 When moisture in the air is cooled, frost or dew drops are formed. Dewdrops or frost may accumulate even on a small space formed at the door. page 17 Such dewdrops may drip onto the floor. Moisture may temporarily collect on the unit. Wipe with a dry cloth. Frost can form easily in the freezer compartment. Try to reduce the time that the door is open. Be careful not to stick any stored foods out of the shelves or cases. Remove dropped items and items trapped between the doors. Lower the adjustable supports to raise the front of the refrigerator slightly and make closing the door easier. page 7 page 9 page 26 page 21 Improper installation or any foreign object might produce a clearance. Then the cold air can flow backward to cause freezing. page 22 The cold air flows backward to cause freezing. Remove the dropped food or plastic. The anti-freeze heater is turned on. This is normal. Is your television or other appliances located near the refrigerator? Is the refrigerator’s power outlet close to the antennae drop area? Sounds suddenly get louder or tone changes. Rattling, squeaking sounds sometimes (every 1 to 2 hours). After the power supply has been turned on, a howling or creaking sound is heard during ice making “STOP” mode (every 1 to 2 hours). Whistle sounds after closing doors, etc. Hissing, bubbling sounds sometimes When the door is opened a whipping sound or a sound like water dripping is heard from the inside of refrigerator. You sometimes hear a “poon” tone, sounding like a mosquito is flying. Low whirring sound sometimes after opening the freezer compartment door. Relocate unit at a distance from televisions and other appliances. Use a dedicated power source. The unit has switched to high-speed operation for powerful cooling during first operation, when temperature is hot, when doors are opened and closed frequently, during “QUICK” mode, etc. These are sounds made during automatic ice making. The unit’s automatic ice maker and pump make a sound every 100 minutes or so, regardless of whether or not the tank is filled with water. These are sounds made during automatic ice making operation check. This sound is made even during “STOP” mode. It is the sound of a fan motor starting to run. It is the sound of refrigerant (gas) flowing. This is a creaking sound made when warm air has penetrated the unit, causing plastic parts to expand. The refrigerator generates the tone when the air flow damper or the HIKARI i-see Sensor is operating. This is the sound of the airflow from the cooling fan. If you think the refrigerator is in trouble, ... When Check if the blue LED has failed as follows. Leave the versa compartment door open. Check if the blue LED in each compartment is illuminated when you open the refrigerator compartment door. It is normal if the blue LED in the versa compartment is illuminated. 29 功能介紹 又能轉動又能調節高度,更好地利用 從上到下的每個棚架 迴轉層架 冷藏室 手好像可以拿得到卻拿不到 最上面最裏面,也能輕鬆地拿出來! 冷藏室 自由 切換室 製冰室 可以在放置食品的 狀態下旋轉棚架。 冷凍室 冷凍室 第 44-45 頁 蔬菜室 用光 LED LE 和過濾器 對冷氣抗菌 ※1、除臭 剛燒好的飯,也可以趁熱瞬冷凍! 穩定食品的溫度,控制結霜和變色。 (抑制凍傷) 自由 切換室 瞬冷凍後的食品, 用軟冷凍保存 冷藏室 軟冷凍 光瞬冷凍 第 41-43 頁 雖說結凍了,但是好切! 第 42-43 頁 ※1 光動銀抗菌、除臭 第 44-45 頁 ※1 在密封容器內對濾網 12cm2 進 情況不同。 無氟利昂雪櫃 靜音設計 這個雪櫃使用非氟利昂冷媒和非氟利昂發泡隔熱材料。非氟利昂冷媒(異丁烷 ) 和非氟利昂發泡隔 影響極小,是對地球環境無害的物質。 聲音很小,只有約 16dB(A)※2。 ※2 根據 JIS C9607 規定的噪音試驗(低速運轉時) 。dB(A):噪音水準單位。分貝 A ■本雪櫃主要針對一般家庭的食品冷凍、冷藏保存用途研製。營業用途請使用營業用冷藏冷凍雪櫃。 ■為因應資源的回收及再利用,主要的塑膠配件均標示材料名稱。 目 錄 安全注意事項 32 從安裝到開始運轉 34 操控面板的使用方法 36 37 ·兒童按鍵鎖 ·最初設定 ·重置設定 高度調節架 冷藏 調高、調低櫃內的溫度 38 再也不用擔心東西就差 那麼一點卻放不進去! 冷凍 想快速製冷(速凍) 蔬菜 可以在放置食品的 製冰 狀態下,上下 移動棚架。 自由切換 冷藏室 冷凍 軟冷凍 選擇製冰方法 39 ·想快速製冰 ·想製作透明度高的冰塊 切換方法 光瞬冷凍 好切冷凍(軟冷凍) 40 41 超強冷凍的正確使用方法 42 第 45 頁 雪櫃的使用方法 冷藏室 節電小竅門 44 45 冷凍室 46 用光 LED 增加 蔬菜的維生素 用光 LED 和過濾器 使水變清潔, 製作味道好的冰塊 自由切換室(超強冷凍室) 46 蔬菜室 47 製冰室(自動製冰機) 48 冰塊的製作方法、停止製冰 49 蔬菜室 保養 製冰室 維生素增量蔬菜室 透明光潔 第 47 頁 冰塊 第 48 頁 行菌類接種,已驗證到其 18 小時後的效果,但測試條件與實際使用 熱材料(環戊烷)不會破壞臭氧層,對地球溫暖化的 自動製冰機的保養 50 ·給水管、水槽座 ·製冰盤(水洗) ·儲水槽 ·水管、給水泵、光學除菌除鉛濾網 51 配件的拆卸方式與保養 52 有需要幫助的時候 特殊情況 54 停電、移動、長時間不用等時候 規格 55 故障排除 56 安全注意事項 安全注意事項 警告 安裝 為預防地震,請將雪櫃安置於穩固的牆壁或 樑柱邊 雪櫃四周留有空間 洩漏的冷媒會在室內積 聚,導致火災及爆炸。 否則雪櫃傾倒,將可能 導致受傷。 第 35 頁 防止傾倒 留有空間 採用以下的標示,區分、說 明錯誤操作時可能發生的危 險與其程度。 否則可能因絕緣不良, 導致觸電或引起火災。 第 警告 操作錯誤時,將可能導致死亡或重 傷。 注意 操作錯誤時,將可能導致個人受傷 或家居、財物受損等。 34 頁 第 34 頁 發生異常或故障時,請立刻中 止運轉,並洽詢經銷商或三菱 電機維修諮詢服務站。 32 34 頁 只可使用指定規格的電源插座 插入電源插頭時,請將電源線朝下,並向內 插到底 若反方向插入時,電源線負 荷過高,將可能導致發熱、 燃燒。 請求維修 電源線向下 電源及電源插頭 避免雪櫃背面擠壓到插頭避免損傷電源線 否則可能導致觸電或受 傷。 擠壓插頭、承載重物、 彎折、綁束電源線等, 都可能導致觸電或引起 火災。 禁止 拔除插頭 請勿使用受損的電源線、插頭與過鬆的插座 請勿以拉扯電源線的方式拔下插頭 否則可能導致觸電或引 起燃燒。 否則可能使電源線受損, 導致觸電或引起火災。 禁止 禁止使用 請清除電源插頭的灰塵 請勿以潮濕的手拔下插頭 否則可能因絕緣不良, 導致火災。 否則可能導致觸電。 清除灰塵 禁止濕手 注意 絕對不要用 潮濕的手觸摸 請務必將電源插頭 從插座中拔出 第 更換或保養雪櫃內燈泡時,請先將插頭拔掉 絕對不要以 水潑灑或淋濕 請務必遵照 指示進行 禁止潮濕 如電源線破損時,請到三菱服務中心購 買一根新的電源線。務必確定所購買的 電源線專為本機而設。 絕對不要觸摸 絕對不要分解、 修理或改造 若使用延長線或分接插頭,將 可能導致發熱或引起火災。 當電線損壞時,必須通知三菱服務中心更換 圖形標示代表的意義如下。 絕對禁止 請使用符合技術規格標籤上所示規格且為雪櫃單獨專用 的電源插座。(技術規格標籤位於冷藏室門墊上。) 避免擺放在水氣或濕氣較重的地方 安裝及搬運 請擺放於穩固、水平的地板,並以可調式支 撐腳確實固定 雪櫃如移動,可能導 致受傷。 第 35 頁 搬運時,請握住搬運用把手 若是手握其他部份, 可能導致受傷。 第 水平擺放 54 頁 握住把手 在開關櫃門時 ·在其他人接触雪櫃時不開關櫃門。 ·關閉櫃門時,手指不放在抽屜式櫃門上面。 ·當心被下面的抽屜夾到腳。(會夾傷腳趾) ·不猛地開關櫃門(食品掉落會導致受傷) ·當心夾到手指。 禁止 安全注意事項 警告 使用 請勿在雪櫃上放置裝有水的容器 請勿在雪櫃內使用電器 請勿存放易燃的揮發性物品 否則若接觸到電子零件 時,將可能導致觸電或 引發火災。 如果冷媒洩漏,並且接 觸電器,可能會產生爆 炸或火災。 揮發油、化妝品、美髮 用品等,可能導致燃燒 或爆炸。 禁止潮濕 禁止 請勿在雪櫃上放置物品 請勿保存藥品或化學試料 否則可能在開關雪櫃門 時落下,導致受傷。 家用雪櫃無法保存需要 嚴密管理的物品。 禁止 請勿吊掛在雪櫃門或把手上 請勿坐在滑動拉門上 請勿承載重物 請勿損毀冷媒迴路或配管,或用螺釘在上面 安裝其他物品 冷媒是可燃性氣體,冷媒洩 漏可能會產生爆炸或火災。 否則製冰盤旋轉時,將 可能導致手部受傷。 否則可能因電氣接點的 火花,導致爆炸或引起 火災。 請勿在附近使用可燃性噴霧 否則電氣接點的火花, 將可能導致燃燒或引起 火災。 禁止使用 禁止觸碰 禁止 發現瓦斯漏氣時,請打開窗戶換氣及通風, 不要觸摸雪櫃 禁止 禁止儲藏 請勿將手伸入自動製冰機(儲冰箱的上方) 以及可自動關門的雪櫃門的機械部份 否則可能使雪櫃傾倒,導致 受傷。 禁止儲藏 請勿用水清洗或噴濺到食物湯汁 不要在室外的小倉庫及車庫中使用 若噴濺到水或食物湯 汁,將可能導致觸電或 引起火災。 電線被小動物咬破,會引起觸電、火災。 換氣 禁止潑灑 禁止使用 開關雪櫃門時,注意不要與周圍的家具碰撞 有可能因雪櫃門或其它部件的損壞而引起受傷。 禁止 故障及長期儲存 如果冷媒迴路損毀,請勿觸摸雪櫃及避免在 附近使用明火,並打開窗戶換氣 有異常狀況時(焦臭味等),請拔掉電源插 頭,中止雪櫃運轉 如果冷媒迴路損毀,請 諮詢零售商店。 如果持續在異常狀態下 運轉,將可能導致觸電 或引起火災。 換氣 長期不使用雪櫃時,請先將門密封墊拔除 否則如有小朋友不慎被 關入雪櫃內,十分危 險。 請勿自行拆解、修理或改造 請勿使用部品已 損壞的雪櫃 否則可能導致受傷、觸 電或引發火災。 拔除插頭 禁止拆解 如果長時間不使用雪櫃,請從電源插座拔掉 插頭,並且打開雪櫃門風乾內部 棄掉本電櫃時,請交給零售商店或專業的工 業廢物回收商 如果雪櫃內部未足夠風乾,冷媒 (氣體)可能由於冷凝器腐蝕而洩 漏,並且造成爆炸或火災。 不正確棄掉而導致冷媒洩漏,會成 為著火的原因並且造成爆炸或火 災。 拔除門密封墊 風乾 正確棄置 注意 使用 請勿強行將食物塞入請勿大力拉扯棚架開門 力道請勿過大 請勿將瓶類放入冷凍室、製冰室或自動切換 室(設置為軟冷凍或冷凍時) 否則可能因食品掉落而 導致受傷。 否則瓶身可能因內容物結 凍而破裂,導致受傷。 禁止 請勿食用走味、變色的食品 否則可能導致食物中毒 或生病。 禁止儲藏 禁止 手部潮濕時,請勿觸摸冷凍室的食品或容器 請勿將手、腳伸入雪櫃下方 關閉雪櫃門時,請握住把手 否則可能導致凍傷。 否則可能被鐵板等割 傷。 請握住把手,以免夾傷 手指。 禁止濕手 禁止接觸 握住把手 33 從安裝到開始運轉 從安裝到開始運轉 10公分以上 附合指定規格、單 獨專用的電源插座 2公分以上 安裝雪櫃 接上電源 安裝的位置 *雪櫃安裝後不久接上電源 請選擇陰涼、通風的位置 以防止冷卻能力降低、節省電費 濕氣少的位置 以預防發霉 穩固、水平的位置 以防止振動和產生嘈音、門半閉及傾斜 若地板為容易陷入的材料,在雪櫃底 下鋪墊堅固的板材。(防止因熱度或 重量導致地板變形或變色) 請使用雪櫃單獨專用的電源 請使用符合技術規格標籤上所示規格且為雪櫃單獨專用的電源插座。 (技術規格標籤位於冷藏室門墊上。) 警告 若使用不符合指定規格的電源插座或使用分接插頭,將可能導致發 熱或引起火災。 即使安裝後不久接上電源,雪櫃也不會損毀。雪櫃需要一段時間 才會冷卻,因此盡快給雪櫃接上電源。 接線 遠離其他電器的位置 以防止電視出現雜音或影像受到干擾 請於周邊保留散熱的空間 在左右預留2公分以上,上方10公分以上 的空間 以便讓熱氣可從兩側與雪櫃頂散逸 警告 請勿堵塞雪櫃的通氣孔,並且應在雪櫃 周圍預留通風位。 如果冷媒滲漏出來,將可能導致燃燒或 爆炸。 機體外側變熱 因為散熱,剛開始使用或于夏季時, 溫度可能達到50~60℃以上。 為保證人體安全,這一設備應有良好的接地。 這一架冷藏冷凍雪櫃的電源插塞一定要插入自己專用電源插口。 這是發揮冷藏冷凍雪櫃性能,並也避免了因雪櫃內連接線過負荷的 原因而引起火災。 必須確認來自電源插口的電壓是正確的。 又無故延長導線,也是不很妥當的。 如果雪櫃安裝在濕度高的地方,建議不單只接地,還要安裝漏電斷 路器。 如電源線破損時,請到三菱服務中心購買一根新的電源線。務必確 定所購買的電源線專為本機而設。 為防止意外發生,當電線損壞時,必須通知三菱家庭電器服務中心 更換。 插上電源後,需要一段時間後才能冷卻 •沒有冷卻的食品及霜淇淋,請在雪櫃充分冷卻之後放進去。 •儘量減少、縮短櫃門的開閉。 第一 次 製 成 冰 塊 在天氣較熱時,可能需要24小時以上。 首先,設定為“通常製冰”。 想使用“透明製冰”時,請變更設定。 34 第 39 頁 儘快接通電源 雪櫃安裝好之後,即使馬上接通電 源,也不會損毀雪櫃。 從安裝到開始運轉 雪 櫃 / 正面下側 可調式 支撐腳 滑輪 按箭咀方向轉動每 個可調式支撐腳直 至支撐腳觸及地 面。 支撐腳蓋 以防止振動和產生嘈音、 雪櫃移動及門半閉 注意 調節與固定 轉動可調式支撐腳,直至支撐腳 觸及地面,而滑輪從地面提起 防止門關不嚴 請調整支撐腳,使 其水準後固定。 前側稍高,櫃門容 易關閉。 未充分調整支撐腳可能因 雪櫃移動而造成受傷。 調整傾斜的門及雪櫃平行 按所示方向轉動可調式支 撐腳,重新調整雪櫃。 右門下垂 右 左門下垂 支撐腳蓋 支撐腳蓋在發貨時隨 產品包裝在包裝箱內 支撐腳蓋的安裝方法 如果安裝地面不平行, 或數日後因食品重量使 雪櫃的支撐腳下沉,門 會向下。請重新調整。 (視乎食品數量,食品 重量會超過100kg。) 按照圖示方向轉動可調 式支撐腳,重新調節。 平行插入支撐腳蓋,直 至頂到進深方向。 支撐腳蓋 左 可調式支撐腳 調高右側 調高左側 用可調式支撐腳無法糾正傾斜時 例如,如果雪櫃安裝在房 間的角落,後面的其中一 個支撐腳可能會下沉。在 雪櫃後面鋪墊滑輪座或堅 固的板材。(一般板材需 要2至3mm厚。) 請勿損毀冷媒迴路或配管,或打釘安 裝其他物品 非氟利昂冷媒是可燃性氣體。但是冷媒迴路是密閉 的,因此不常滲漏出來。 警告 如果冷媒迴路已損毀 1. 請勿在附近使用電器用品或消防設備。 2. 打開窗戶使室內空氣流通。 請聯絡購買處的經銷商。 後部支撐腳 滑輪座或堅固的 板材 預防地震 將堅韌的固定帶穿過背面上方的固 定孔(兩個),固定在穩固的牆壁 或樑柱上 堅韌的固定帶 警告 若雪櫃傾倒,將可能導致受傷。 35 操控面板的使用方法 上 顯示 操控面板的使用方法 表示正在顯示哪個 表示顯示中的儲藏 在超強冷凍運轉過 顯示製冰室的設 儲藏室。 室的設定。 程中顯示。 定。 操作按鍵 下 切換顯示的儲藏室。 進行溫度調節。 進行超強冷凍。 第 每按一次,切換畫面顯 示。 冷藏室 冷凍室 蔬菜室 自由切換室 第 38 頁 第 40 頁 軟冷凍 製冰方法 只在自由切換室被設定 為軟冷凍(L、M、H) 時可以使用。 長期不製冰時 第 39、49 頁 第 49 頁 ※顯示因為是說明,與實際顯示不同。 其他設定 兒童按鍵鎖 由於小孩頑皮等,即使錯誤操作操 控面板上的按扭,也不會執行任何 操作。 ※在兒童按鍵鎖狀態下,只能進行儲藏室選擇操作。 同時按住 的蜂鳴音)。 鍵和 鍵約3秒(直至發出“嗶嗶” 燈亮起來。 解 除 與上述操作步驟相同。 速凍運轉 想盡快冷卻食品、飲料時 冷藏室、冷凍室、蔬菜室 第 38 頁 自由切換室(僅限於設定在冷凍時) 第 40 頁 36 切換製冰設定。 41 頁 ICE MAKER CLEANING(HOLD 5 SEC) 想清洗製冰盤時 第 50 頁 除非清洗製冰盤,請勿長時間按住這個按鍵。 如果超過30秒不進行任何操作,為了節電,背景燈會熄滅。(設定的內容已存儲) 但是,只有超強冷凍時的 ,在超強冷凍運轉過程中,顯示燈不熄滅,顯示 。 操作按鍵時,背景燈會亮起來,但是還沒有執行操作,所以,燈亮起來之後,請速操作按鍵。 顯示自由切換室 超強冷凍 運轉中 將製冰室的製冰 設定調為“CRL” 操控面板的使用方法 顯示例 將自由切換室的溫度 調節設定在“SOFT FZR•M” 例:顯示自由切換 室時 【安裝時(買入時)的狀態】 最初設定 請按照自己的 喜好進行設定。 冷藏 溫度調節、中 製冰 通常製冰 自由切換 軟冷凍 溫度調節、中 冷凍 溫度調節、中 未設定 兒童按鍵鎖 超強冷凍 蔬菜 溫度調節、中 門開警告 速凍 重置設定 用門開警告(“嗶嗶”的聲音)次數表示以下狀態。 4次※ 冷藏室、製冰室或者冷凍室的門打開超過1分 鐘。請把門關上。 在記不清設定內容等時候。 把儲藏室選擇、溫度調節、速凍、超強冷凍 的設定恢復至安裝時(買入時)的狀態。 ※門打開每超過1分鐘,響4次,如超過5分鐘,則連續響。 請確認門有沒有關嚴、門縫中有沒有夾著東西(包裝袋、盒的 後側)。 伴隨著 每月檢查一次門的密封情况。 “嗶嗶” 如果門關上了,警告仍然在響,請諮 的聲音閃爍。 詢所購買的商店。 伴隨著門開警告聲音,通過閃爍操控 面板,通知給主人。 同時按住 鍵和 鍵約3秒 (直至發出“嗶嗶”的蜂鳴聲)。 操控面板的顯示閃爍時 的溫度調節不變。 製冰室的設定為 時,變為 時,沒有變化。 。其他設定 每隔一定時間,所有顯示均閃爍3次,或者操控面板顯示或者溫度調節顯示按順序反復閃爍時,是示範運轉狀態。 在這種狀態下,雪櫃不製冷。 請解除示範運轉模式。 第 54 頁 37 冷藏室、冷凍室、蔬菜室的設定 調高、調低櫃內的溫度 想快速冷凍 調高、調低櫃內的溫度 ※顯示例 ※顯示例 想快速冷凍︵速凍︶ 按 鍵,顯示 想調節的儲藏室。 按 鍵,進行 溫度調節。 每按一次,顯示改變一 次。 每按一次,在 之間變換。 各個儲藏室的溫度調節如下所示。 每按一次,顯示變換 一次。 按住 鍵約3秒 (直至發出“嗶嗶” 的蜂鳴聲)。 約在2小時後自動結束 燈亮起來。 燈熄滅。 *1 儲藏室顯示 溫 度 調 節 過冷時 比“M”調高 比“M”調高 比“M”調高 2~3℃ 2~3℃ 2~3℃ 稍冷時 比“M”調高 比“M”調高 比“M”調高 1~2℃ 1~2℃ 1~2℃ 標準 按 鍵, 顯示想進行速凍 的儲藏室。 約0~6℃ 約-16~ -22℃ 中途想 中止時 按 鍵, 燈關閉。 有關自由切換室的速凍 第 40 頁 有關超強冷凍 第 41 頁 約3~9℃ 想再冷一點時 比“M”調低 比“M”調低 比“M”調低 0~1℃ 1~2℃ 1~2℃ 想更冷一點時 比“M”調低 比“M”調低 比“M”調低 1~2℃ 2~3℃ 2~3℃ ※1:溫度與自由切換室的冷凍設定不同。 有關自由切換室的溫度調節 第 40 頁 ※想再詳細地進行溫度調節時 第 55 頁 ※想把冷凍室切換成低溫冷凍設定時 第 54 頁 有關櫃內的溫度 •上述溫度僅為示例。根據食品的放置狀態、櫃門開閉等 使用狀態,溫度會與上述溫度有所差異。 •在除霜前後等時候,雪櫃內溫度會短暫出現或高或低的 情況。 •標準溫度是在周圍溫度30℃、不放入任何食品關閉雪櫃 門並在溫度穩定時,在雪櫃內靠近中央稍下一點處測得 的溫度。根據食品的放置狀態、櫃門開閉等使用狀況, 溫度會與上述溫度有所差異。 38 什麼時候使用 ? 由於一次性大量採購東西,放入大量食品 時,採用速凍方式,保持食品的新鮮度。 •可以在放入食品狀態下進行速凍。 •速凍後變為設定溫度。 •速凍過程中,因為高速運轉,噪音較大。 製冰室的設定 製冰室的設定 選擇透明製冰,速度較慢。製冰需要的 時間長,約需5~8小時。 •想儘快製冰時,請控制製冰室門的開閉次數。 想快速製冰 製冰時間請參閱下面的“每次製冰時間 的標準”。 ※顯示例 按 鍵,使 燈亮起來。 自動結束 製冰設定可以在4種模式之間切換。 (通常製冰) 想大量製冰時 燈亮起來。 下列情況下,自動結束。 •約經過9小時,或者儲水箱裏面的冰塊已滿時 (60~100個左右) •儲水槽裏沒有水時 •快速製冰時,因為是高速運轉,噪音稍大。 •剛安裝完後進行快速製冰,有時可能會需要24小時以 上,冰塊才能製作完成。 想快速製冰 按 鍵,參考下表,選擇製冰設定。 安裝時(買入時),設定為 。 每按一次,顯示都會變換。 燈熄滅, 選擇製冰方法 選擇製冰方法 想稍快一點進行透明製冰時 想提高透明製冰的透明度時 將製冰設定為 。 同時按住 鍵和 鍵和 (快速製冰) 想更快一點製冰時 (透明製冰) 想製作透明度高的冰塊時 比“通常製冰”所花時間長。 (約5~8小時) (製冰停止) 作為冷凍室使用時 為防止發生黴變,請清洗儲水 槽、水管等。 第 50、51 頁 ※製冰方法(給水等) 第 49 頁 鍵約3秒(直至發出“嗶嗶” 的蜂鳴聲)。 閃爍 燈亮起來, 中的任一個閃 爍。其他儲藏室的顯示暫 且熄滅。 按 鍵, s想快速製冰時,使 閃爍。 s想提高透明度時,使 閃爍。 s安裝時(買入時)設定在 上。 過一會之後,發出“嗶嗶”的蜂鳴聲,閃爍變 為亮燈狀態,約亮2秒之後,燈熄滅。 即使在L、M、H中選擇一個,也只有 燈亮。 其他儲藏室的顯示恢復原狀。 每次(7~8個)製冰時間的標準 製冰時間 標準透明製冰時間及透明度 急速製冰 60~100分鐘 通常製冰 100~130分鐘 顯示 透明製冰 5~8小時 製冰時間 •製冰時間因周圍溫度、使用狀態、水的種類、放入儲水 槽中的水的量、溫度而異,有時會比上述時間長。 •冬季等周圍溫度低的時候 •雪櫃門開閉頻繁時 透明度(透明 部分比例) L M H 比“M”快 約5~8小時 比“M”慢 冰塊的 70%~80% 冰塊的 80%~90% 冰塊的 90%~ 39 自由切換室(超強冷凍室)的設定 切換方法 切換方法 ※顯示例 軟冷凍和冷凍的區別 •用好切冷凍保存肉、魚等2~3周 左右時。 •進行超強冷凍時 •保存肉、魚、其他加工食品1個 月左右時。 按 鍵, 顯示 。 冷凍後過硬的食品變得好切 水分多的食品 •煮過的蔬菜 •肥肉少的大塊肉 按 鍵, 根據您的喜好, 進行溫度調節。 想快速製冷時 ※自由切換室設定為冷凍時 約-5℃ 好切冷凍的最適宜溫度 可以放在託盤裏冷凍。 ※顯示例 約-7℃ 食品難以凍結時 鹽分、糖分多的食品 •醬油醃制食品、醬醃制食品 •鹹鱈魚子 按 鍵,顯示 。 約-9℃ 保存鹽分、糖分多的食品時 可以保持食品原味。 按 鍵,顯示 。 ※軟冷凍不能進行速凍。 按住 約-12℃ 在冷凍 、冷凍 狀態下, 無法保存市售的冷凍食品、霜淇淋。 保存在家庭保存的 食品1個月左右時 約-15℃ 保存市售的冷凍食品、霜淇淋等 時候 以方便使用的硬度 保存霜淇淋。 約-18℃ 鍵約3秒(直至發出“嗶嗶” 的蜂鳴聲)。 亮起來。 約在2小時後自動結束 熄滅。 中途想 中止時 按 鍵,使 熄滅。 •自由切換室設定為軟冷凍時,不能進行速凍。如進行 速凍操作,會發出“嗶嗶”的蜂鳴聲。 •速凍過程中,因為高速運轉,噪音稍大。 ※溫度與冷凍室不同。自由切換室設定為冷凍時,保存期請設定為1個月。 ※想更細進行溫度調節時 第 55 頁 •在除霜前後等時候,雪櫃內溫度會短暫出現或高或低的情況。 •標準溫度是在周圍溫度30℃、不放入任何食品關閉雪櫃門並在溫度穩定時,在雪櫃內靠近中央稍下一點處測得的溫度。 根據食品的放置狀態及雪櫃門的開閉等使用情況,溫度會與上述溫度有所不同。 40 •超強冷凍運轉過程中,顯示 。 •一旦操作按鍵,背景燈亮起來。 •持續30秒沒有任何操作,背景燈熄滅。 光瞬冷凍 想美味冷凍 趁熱放入,用超強冷凍保持原味,用好切冷凍方便保存 光瞬冷凍 ※自由切換室設定為軟冷凍時 用超強冷凍模式,可以防止 食品變質、走味,使味道鮮 美。 快速冷却熱的食品。 剛燒好的米飯、剛做好 的咖喱飯等熱的食品 •可以保持食品的水分和口感,進行美味冷凍。 防止食品變質、走味,進行美味冷凍。 肉、魚等食品 •在進行肉等食品的解凍時,几乎不會流失美味成分。 •馬鈴薯、竹笋、青花菜也可以保持好的口感。 超強冷凍 結束 用好切冷凍(軟冷凍) 保存 可以省去分小、解凍的時間。 •看上去凍結得很硬,但是拿出來用菜刀可以切開。 ※想長期保存時,請在超強冷凍結束後,放在冷凍室裏面保存。 ※顯示例 無論熱的東西還是冷的東西,超強冷 凍的操作方法是一樣的。 用光i-see感測器測量食品溫度,自動 判斷後進行冷卻。 按 為了更好地進行 超強冷凍,請參 閱下一頁! 鍵,顯示 。 確認顯示了 。 如果處於冷凍設定狀態,先設定為軟冷凍。 第 40 頁 等溫度穩定下來後(約2小時後),進行超強冷凍。 ※在冷凍狀態下,無法進行超強冷凍。 按 。 自動結束 燈亮起來。 持續30秒不進行任何按鍵操作, 以外的燈熄滅。 燈熄滅。(約3~12小時後) ※根據食品的數量、溫度、種類而異。 超強冷凍後,用軟冷凍保存。 中途想中止時 按 ,使 的燈熄滅。 •可以在放入食品狀態下進行超強冷凍。 •在超強冷凍過程中,可以開閉自由切換室。 •按超強冷凍鍵,發出“嗶嗶”的蜂鳴聲時, 只有自由切換室才有超強冷凍的功能。除了自由切換室,其他儲藏室,無法進行超強冷凍,另外,自由切換室設定 在 時,無法進行超強冷凍。 •在超強冷凍運轉過程中,儲藏室選擇不是 時,不會顯示 。 •在超強冷凍運轉過程中,自由切換室設定為 時,超強冷凍結束。 •光i-see感測器在超強冷凍開始後連續動作5分鐘。以後,在經過1小時~5小時,10分鐘動作1次,1次1分鐘左右。光 i-see感測器動作過程中,會發出“啪”的動作聲音。 •自由切換室的藍色LED與冷藏室的藍色LED及光i-see感測器動作連動亮燈。打開自由切換室的門時,燈並不是總是亮著的。 41 軟冷凍 光瞬冷凍、好切冷凍(軟冷凍) 保存容器方面 光瞬冷凍、好切冷凍︵軟冷凍︶ 光瞬冷凍 食品的上面、米飯 的包裝,最好用保 鮮膜。 熱的食品 例如: 剛燒好的米飯:約70℃。 正確的 使用方法 為了再次 美美地食用 •鋁箔、紙包裝因為無 法正確測得食品溫 度,請避免使用。 不要放入80℃以上的食 品。 在裝入密閉容器等裏面 時,食品要裝滿容器。 •在大容器裏只裝入一點點 食品時,可能無法正確測 得食品溫度。 •會導致周圍食 品溶化或容器 變形。 然後,在放入、拿出無法用 手直接拿的熱的食品時,請 當心不要被燙傷。 直接冷凍熱的東西 肉、魚 不讓水分、美味流失。 省去放涼的時間,不會忘記放入雪櫃。 超強冷凍肉、魚等,然後用好切冷凍(軟冷 第 41 頁 凍)保存。 米飯 用軟冷凍,取出後可以用菜刀切開食品。 剩下的米飯,建議趁熱分成 1人份量,用保鮮膜包好, 進行超強冷凍。 如果保存2周左右,用軟冷凍保存。 這樣可以減少解凍不均勻,解凍效果好。 省去冷凍時的分小、解凍時間,提高調理速度。 咖喱 剩下的咖喱,可以趁熱 放入自由切換室進行超 強冷凍。 含有馬鈴薯的咖喱也可 以無損口感地進行保存。 •冷凍之後軟冷凍、軟冷凍之後冷凍時,要在1~2周內 儘快使用。 肉塊 建議超強冷凍時,每塊肉重量設定在100~400g左右。 冷凍保存的肉及冷凍採購的肉, 可以在軟冷凍後使用。 •因大小而異,從冷凍移至軟 冷凍,約2~5小時左右過後, 可以輕鬆切開。 薄肉片、培根 醬類 剛做好的醬類也可以趁熱倒入保存容器,進行超強冷 凍。凝固後,用菜刀切成塊狀,裝入保存袋內,這樣 可以節省空間,並可以取出需要的量使用。 可以直接切絲。 下鍋調理、添加醬料時,會自然解凍,剝離。 •取 出 後 不 能 馬 上 撕 碎 時,請放置一段時間後 撕碎。 絞肉 可以直接切下所需的份量。如 果再分切成小方塊狀,在室溫 下放置15~30分鐘,就可解凍至 可用手攪拌的程度。 煮好的蔬菜可以趁熱用超強冷凍預冷卻。 馬鈴薯、青花菜 可以進行用於炸肉餅、 沙拉的煮蔬菜的預冷卻。 42 魚片、鱈魚子 魚片不須解凍,可直接以小火烹煮。鱈魚子等鹽分含 量較高的食品,不會完全結凍,可直接烹煮、調理。 從自由切換室的上部可以通過光 i-see 感 測器看到食品的狀態。放入食品時,請 保證便於測量食品溫度。 放入食品時 整體同時進行超強冷凍。 需要超強冷凍的食品放在 自由切換室的最上部、平 放。 •如被擋住,無法正確測量 溫度。 水果、甜點 各種水果,請用超強冷凍保存。 ※建議把熱的食品放在外 面,與凍結食品分開。 •熱的食品接觸到凍結 食品,會使凍結食品 溶化。 其他 納豆、油豆腐 特別甜的水果建議採用這一方式。 納豆取出後可直接攪拌。 在經過超強冷凍後的水果上加上優酪乳、牛奶等, 經榨汁機攪拌,即可製成簡單健康冷飲。 冰涼的納豆也十分可口。 也可以簡單地製作糖分少的健康生果醬、霜淇淋。 •水果即使解凍,也無法恢復到冷凍前的狀態,所 以,請不要解凍直接食用。 •水果在軟冷凍保存一周以上,會發生變味。為了保 持好的口感,請在2~3日之內食用。 •因糖分不同,結凍所需時間也不同。自開始超強冷 凍後,請放置1個晚上再食用。 西瓜 切成一口大小的方塊狀,超強冷凍後就成為清涼消暑 的西瓜冰。請用各種水果試試。 思慕雪(smoothie) 用蘋果和獼猴桃製作思慕雪 蘋果1/2個,剝皮,切成一口大小, 獼猴桃1個,切成1cm寬的圓片,去 皮,超強冷凍。 往榨汁機中加入超強冷凍後的蘋果和 獼猴桃、牛奶250cc、蜂蜜(根據個 人喜好),攪拌至均勻(2人份)。 冷凍優酪乳 直接把裝在盒子裏的加糖優酪 乳放入雪櫃進行超強冷凍。 放置1個晚上,就形成細膩可 口的霜淇淋。 生果醬 草莓生果醬 將1袋草莓(約300g)放入容器中,搗碎。 放入砂糖60g~100g(根據草莓的甜度調整),攪拌,超 強冷凍。 放置一晚即可。 •因少量水果可以輕鬆製作,請在 水果吃剩等時候試著製作。 光瞬冷凍、好切冷凍︵軟冷凍︶ •隨後追加,可能會無法 •同時放入熱的東西和常 進行超強冷凍。 溫以下的冷的東西,優 先冷卻熱的東西。 放在什麼地方? 油豆腐可依份量,切成小 塊使用。 不適合超強冷凍、軟冷凍的食品 •經過解凍的食品,請避免再次冷凍。 否則無法保證口味、品質。 •不能冷凍的東西,不適合軟冷凍。 否則,無法保證冷凍前的口 味及品質。 例如,蒟蒻、豆腐、牛奶、生雞蛋等。 •市面銷售的霜淇淋、冷凍食品不能 用此方式保存,請在冷凍室保存。 有關超強冷凍、軟冷凍 •超強冷凍、軟冷凍約在-7℃結凍,因此,有時食 品需要花24小時左右才能完全結凍。 •超強冷凍運轉結束後,即使 燈熄滅了,有時 食品也會沒有完全結凍。 •在新放入食品等時候,盡可能減少雪櫃門的開閉 次數。 •根據食品的種類、調理方法、食品的放入方法 (疊加、放入地方)、食品的量、保存期限,有 時會無法進行超強冷凍,或者凍結及冷凍程度有 所改變。 •食品會因所含糖分、鹽分、脂肪等,沒有凍結或 凍得很硬(不能用刀馬上切開)。 •凍得很硬時,室溫放置約5~15分鐘,即可用刀切 開。 •請根據食品的凍結程度,進行溫度調節。 第 40 頁 43 冷藏室 食品凍結時 •冷藏室溫度調節在“H”時。 •周圍溫度在5℃以下時。 請把冷藏室的溫度調節調至“M”、“LM”、“ L”。 二變式靈活摺架 迴轉層架的使用注意事項 雪櫃內燈泡 如雪櫃門打開超過4分鐘, 雪櫃內燈泡每分鐘閃爍兩次以提醒主人。 雪櫃內燈泡持續亮起60分鐘後會熄滅。 門關閉後,下次打開門時雪櫃內燈泡會再次亮起 迴轉層架 關 閉 雪 櫃 門 之 前, 要 使 迴轉層架恢 復 到 原來的 位置 不要使物品從迴轉層架上 垂下 高度調節架 吹風口 不要使物品伸出迴轉層架 微凍雞蛋架 活動雞蛋架 冷藏室 請勿在迴轉層架上放置以 下物品 ˙ 請勿疊放瓶類等易滑物品 節電小竅門 ˙ 容易灑出的物品 ※ 總重量不能超過 10kg。 保存肉、魚、加工食品 (魚糕、火腿等)、優酪 乳等。 ● 熱的東西待冷卻后再放入。 ●開閉雪櫃門的次數要少,時間 要短。 ● 關閉雪櫃門時注意不要夾到食品、 食品掉落可能會導致受傷,也 可能造成棚架和瓶架破損。 自動設定 塑料袋、電源線等。 微凍 約 -3 3℃ ※ 在吹風口附近放置水分多的食品,會凍結。 ■發出門開警告時 滑動微凍箱 小件箱 ● 食品之間保留間隔。 ˙ 無法用操控面板進行溫 度調節。 ˙ 請不要放入容易凍結的 食品。 第 56 頁 第 37 頁 味道重的食品,要包好保存 44 容易串味的食品 容易變味的食品 薤、乾貨、納豆、味噌醬、牛肉、鹹菜、沙丁魚、泡菜、 布丁、霜淇淋、土豆沙拉、豆腐、米飯、麵包、牛奶、 餃子等 蛋糕、冰塊等 ˙ 有時會殘留一點點味道。 ˙ 有時會殘留一點點味道。 棚架、瓶架可動 擺放食品時,請勿突出於 棚架 瓶架的前列,請勿放置無 法放到底的瓶罐 。 活動盤 (小) 這樣做會出現門半閉及瓶罐掉落 破碎。 (也可以拆下來) 迴轉層架 ①將左右的拉桿向外側滑動卸下。 ②握住托盤的邊緣,慢慢旋轉 (托盤可以向左右兩側旋轉。) ② 活動盤 (大) 活動盤 (中) 藍色 LED 用光能去除 雜菌和異味。 連續亮5分 鐘後會熄滅。 請勿在雪櫃門盤架外側放 置市售的管架 雪櫃門無法完全閉合,會降低 冷卻效果,或是因為食品掉落 導致受傷,也可能造成箱和蓋 等破損。 ① ① 使用後,請按照相反的順序轉回原來的位置,將左右兩側的拉 桿固定在鎖扣的位置。 第 52 頁 ■迴轉層架的拆卸和安裝方法 瓶架 高度調節架 在滑動微凍箱、小件箱 的外部放有食品時,請 不要關門 down 冷藏室 節電小竅門 左右移動拉桿,調節架子間隔。 up 高度調節架脫開時,請從上面推入脫開的支撐腳。 ■高度調節架的拆卸和安裝方法 第 52 頁 盒子要切實放好 二變式靈活摺架 ● 下述情況下食品凍結時,請把冷藏 1 用作開闊的架子 室的溫度調節調至“M” 、 “LM”、 “L”。 說明 活動盤 上層可調節3段高度, 下層可調節2段高度。 ˙ 冷藏室溫度調節在“H”時 ˙ 冬天等周圍溫度在 5℃以下時 第 38 頁 ●因照明燈使用長壽命發光二極體 (LED),所以通常不需要更換。 2 縮減一半,放置較高 的東西 ① ② ③ ① ② ■活動盤的拆卸方法 第 53 頁 45 冷凍室 自由切換室 (超強冷凍室) 門開警告 第 37 頁 如果雪櫃門(冷藏室、製冰室、冷凍室)打開超過1 分鐘,會響起警號,避免冷氣洩露,減少電力浪費。 請確認門有沒有關好、有沒有夾到食品(包裝袋、 包裝盒的後側)。 ※請每月檢查一次門的關閉狀態。 伴隨門開警告,通過操控面板的背景燈閃爍通知主 人。 光i-see感測器 (紅外線感測器、藍色LED) 檢測放置食品的位置和食品溫度。 鋁盤 用冷卻好的託盤迅速 冷卻食品。 冷凍箱(上) 冷凍室/自由切換室 切換盒 食品堆得不能比盒子高 會弄壞食品。 會導致食品溶化。 會導致門關不上。 冷凍箱(下) 有關收納 冷凍箱下面不要放高度較高的東西 較高的東西可能會弄壞食品及冷凍箱。 會導致門關不上。 選擇自己喜歡的冷凍方式 軟冷凍和冷凍的區別 軟冷凍 冷凍 46 第 40 頁 用好切冷凍保存肉、魚等食品2~3 周左右時。 進行超強冷凍時。 保存肉、魚、其他加工品約1個 月時。 蔬菜室 LED(天頂部) 請勿分解LED或讓LED沾上水。 進水會導致故障。 因使用長壽命發光二極體(LED),所以 通常不需要更換。 滑動箱 請勿在滑動箱下面放入高度 比較高的物品。 這樣做會損壞食品或者滑 動箱。 使用時若拆下滑動箱,會 使蔬菜室變得乾燥。 會導致門關不上。 蔬菜室 蔬菜箱 可放入2L膠樽。 在光照下,自己增加營養素! 維生素增量 LED燈一直亮著 蔬菜、水果如果包著保鮮膜保存,保鮮更持久! 蔬菜是收割後仍然活著的食品。在光照下,自己會增加營養素。 幾乎沒有不能通過LED光的照射而保存、收藏的蔬菜、水果、飲料、調味料。使用方法與通常一樣。 即使照射的光線微弱,蔬菜的營養也會增加。因此,除非包裝將光線完全阻隔,否則不需要將包裝拆除。 蔬菜的營養並不會持續增加。保存期限依據購買時的新鮮度而定。請盡可能在蔬菜新鮮時食用。 蔬菜室的濕度很高,如果蔬菜室放置大量綠葉蔬菜,每個儲存箱的底部可能會出現霧氣或有露水形成。如 果儲存箱底部有露水形成,這會使儲存箱底部變得骯髒,請用幹布擦擦儲存箱。 47 初次使用時 製冰室 初次使用或一週以上未使用時,請將前2~3次的 冰塊(約20個)丟棄。 可能會有臭味或灰塵附著。 (自動製冰機) 門開警告 第 37 頁 給水栓 如果雪櫃門(冷藏室、製冰室、 冷凍室)打開超過1分鐘,會響起 警號,避免冷氣洩露,減少電力 浪費。 伴隨門開警告,通過操控面板的 背景燈閃爍通知主人。 儲水槽蓋 水管 給水泵 光學除菌除鉛濾網 儲水槽(約1.2公升) V-LED燈 給水管 以光學除菌除鉛濾網,以免細菌在儲 水槽中滋生。 V-LED燈號會在下列情況中亮起︰ 製冰盤 •當冷藏室或製冰室門打開時(但燈 號會在冷藏室門打開5分鐘後熄 滅。) 無法拆出。 靜音墊 •給製冰盤加水前後 製冰室 減低冰塊掉落在儲冰箱 中的聲音。請勿丟棄靜 音墊。 儲冰箱 •自動製冰機必須定期 清洗。 第 冰鏟 50 頁 製冰時的注意事項 請勿在儲冰箱深處放置物品 檢測桿 (偵測儲冰存量) 門 冰鏟 儲冰箱 將冰塊推平 48 除了水以外,請勿於儲水槽加入糖、果汁、茶等其他液 體。(耐熱溫度約為60℃) 加入水以外的液體,可能導致給水泵 故障。 •將食品儲存在儲冰箱中,食品高度必須少於儲冰箱 的高度。(這樣會造成故障或防止雪櫃門關閉。) 儲水槽加水時,請勿超過滿水位標示。 水槽水位過高時,製作出來的冰塊可 能會連在一起。 •檢測桿會自動偵測儲冰存量,到達一定程度就會停 止製冰(60~100塊)。 為正確檢測儲冰量,請將冰塊推平,並將冰鏟置於 儲冰箱前。如果撞到物品,自動製冰機可能會被損 毀。 在用礦泉水等礦物質成分多的水製作的冰塊中,會有白 色沉澱物(白色結晶)。 溶于水後,會呈現纖維狀。這是礦物成分結晶物,對身 體無害。 長時間放置冰塊,冰塊與 冰塊之間會粘在一起或者 變小。 冰塊的製作方法 在操控面板上按 或 。 第 39 頁 ,選擇 、 •初冷安裝時(剛購買時),已自動設定 。 透明製冰模式下,結冰速度很慢。 需要很長時間才能結凍。 想調節透明度、製冰時間時 第 39 頁 停止製冰 長時間不用時 強制將製冰盤中的冰塊或者水倒入儲冰箱中,清空製 冰盤。 取出儲水槽,關閉製 冰室門。 每按按鍵一次,選項的顯示切換一次。 製冰室 檢查儲水槽中的剩餘水量。 •打開冷藏室門,從儲水槽上方觀察水位。 儲水槽 按住操控面板的 鍵約5秒(直至發 出“嗶嗶”的蜂鳴聲)。 儲水槽 製冰室 •製冰室設定顯示( 、 、 、 中的任意一個)閃爍 約1分鐘 。(倒出製冰盤 的水、冰塊) •閃爍結束後,恢復原狀。 取出儲水槽、打開給水栓,將水注入。 警告:僅限飲用水。 至滿水位置標示為止。 取出儲冰箱,倒掉水、 冰塊。 s 不要扔掉靜音墊。 儲冰箱 製冰室的製冰設定設為 •儲水槽傾斜時,水可態會溢出。 •如果儲水槽沒有正確放置,製冰室不會製作冰 塊。 此外,儲水槽可能會被冷凍。 檢查儲水槽或給水管內沒有異物。 第 第 39 頁 用水清洗儲水槽(給水泵、水管、光學 除菌除鉛濾網)、給水管、儲冰箱、靜 音墊,晾乾後,歸入原位。 冰塊的製作方法 蓋上儲水槽蓋,將儲水槽保持水平並裝回 其原本位置。 。 s 重新製冰時, 請切換製冰設定。 第 39 頁 將儲水槽歸入原位 50 頁 冰塊形狀 關於透明製冰 •製成的冰塊形狀是不規則的四邊形、 平的梯形或菱形。 •冰塊中可能有白色的沈澱物(白色結晶體)或氣 泡。 •一次製成的冰塊大小會按儲水槽中的水量而改變。 •下面的情況可能會使透明的冰塊中出現白色沈澱 物。 . 從“通常” 、 “速凍” 、 “停止”切換到 “透明” 。 (首先設定為“ ”) . 製冰的水包含許多礦物質。 (這些白色沈澱物是礦物質成份的結晶體,對人體 無害。) . 雪櫃周圍的溫度、使用狀態變更時。 . 冰塊長期儲存在儲冰箱時。 (冰塊上面會有結霜現象。如果將冰塊放入水中, 結霜會溶解。) •一批可製成7至8顆冰塊。 •如果儲水槽的水高過滿水位置,製冰盤 的水道會冷凍,形成2至3顆冰塊黏在一 起和不平整的冰塊。 •如果冰塊儲存得太久,冰塊會黏著或縮 小。(這種現象稱為“昇華作用”。) •速凍製冰時,有時會因急速冷凍而使冰 塊破裂,產生裂縫。 •在敲碎粘在一起的冰塊時,當心不要弄傷手。 49 自動製冰機的保養 每月清洗、保養一次 給水管、水槽座 給水管 拔除給水管, 用乾淨抹布將水槽座擦拭乾淨。 •恐造成故障,不要讓水流入水槽座。 水槽座 分離後,以清水清洗。 •鋁管請旋轉安裝。 ※ 給水管可以由於礦物或氯氣變成白 色,但這不屬於異常。清洗水管並且 繼續使用。 鋁管 墊片 給水管 A面 以相反程式裝回原狀 •為了避免A面與B面出現段差,請確實 裝入給水管。否則,如果水管安裝不正 確,製冰機會發生故障。 B面 水管接合部 認水管與水管的接合部 有沒有異物。 保持水平 •沒有切實插入,或者由於異 物有間隙時,會導致儲水槽 凍結。 水管 儲水槽 請勿夾入異物 水槽座 (雪櫃主機側) 給水管 每月清洗、保養一次 每週清洗、保養一次 自動製冰機的保養 製冰盤(水洗) 儲水槽 使用儲水槽的水清潔製冰盤 取出儲冰箱內的冰塊,關閉製冰室門。 取出冰塊 將槽蓋拆下,以清水清洗。 (耐熱溫度約為60℃) 將水注入儲水槽後裝回。 按住操控面板上的 鍵約5秒 (直至發出“嗶嗶”的蜂嗚聲)。 •製冰室的顯示( 、 、 、 (使用儲水槽內的水沖洗製冰盤) )會閃爍( 約1分鐘 )。 重複步驟 2~3次。 取出儲冰箱,倒掉水與冰塊。 •請勿丟棄兩層靜音墊。 50 儲冰箱 ※ 根據水的種類,如果容易發生 黴變,請每週保養2、3次。 保養儲水槽、蓋子使用漂白 粉時,請按照相應的注意事 項。 為了確保冰塊的衛生和可口,請定期清洗、保養。 定期清洗、保養可防止水垢與霉菌等的產生。 每月清洗、保養一次 水管、給水泵、光學除菌除鉛濾網 將水管拔除。 將給水泵以旋 轉方式拆下。 拆除部件,並且用清水沖洗。 水管 光學除菌除鉛濾網 以相反程式裝回原狀。 清洗光學除菌除鉛濾網時,請勿使 用廚房用中性清潔劑、揮發油或漂 白劑等清潔用品。 •否則會導致冰塊出現異味。 蓋帽 光學除菌除鉛濾網通常毋須更換,但 遇到以下情況時敬請更換。 給水泵 •侵入水以外的物體造成阻塞時。 翼片 翼片用磁石製成,請確 實用水清洗,不要殘留 異物。 蓋 •破損時。 凸塊 •當濾網發黴時。 在此情況下,請向經銷代理商洽詢。 ※根據水的種類,容易發生黴變時, 請每月清洗2、3次。 一邊用手指將凸 塊向下推,一邊 將其拆下。 將給水泵、水管恢復原位的順序 組裝不完全時,會引起無法製冰、驅動聲過大的問題。 組裝給水泵 將濾網嵌入蓋帽。 安裝水管 旋轉蓋帽的鉤部(C), 鉤住給水泵的凸塊部(D)。 ※確保翼片在給水泵內。 對準儲水槽的▲符號插入水管。 符號 水管 在中嵌入蓋帽的凸 塊(A)和鉤扣(B)。 D C 旋轉 自動製冰機的保養 B 連接水管和給水泵。 ※請確認水管與水管之間的接合部 沒有異物。 旋轉給水泵裝入儲水槽 A (切實地)。 旋轉 將翼片裝到 給水泵上。 水管接合部 給水泵 51 配件的拆卸方式與保養 保養前 保養方法 將電源插頭拔掉 警告 如果不拔掉插頭, 可能導致觸電。 •用柔軟的抹布蘸溫水擦拭,或者拆卸下來水洗。 •對難以去除的污垢,用抹布蘸稀釋後的廚房用清潔劑(中性) 去污,並用清水擦拭。 特別是油漬,不去除掉會導致塑膠部件破裂。 注意 請勿使用鹼性/弱鹼性廚房用洗滌精、研磨粉、 請隔10分鐘以上,再將電源插頭插 回。 如果立刻插回,機器將不會動作。 洗衣粉、酒精、揮發油、稀釋劑、石油、酸、 刷帚、熱水等。 因為這些東西會導致塑膠部件(門把手、蓋、箱等)破裂,損傷雪櫃 的門及油漆面。 迴轉層架 拆除棚架 安裝棚架 拆除托盤 1將左右的拉桿移動到“鎖 扣”的位置。 拉桿 1確保拉桿處於“鎖扣”的位置。 拉桿 拉桿 拉桿 2將迴轉層架放入雪櫃內的左右軌道 上,先推到最裏面。 2雙手托住迴轉層架,使後部略 微翹起,插至底部。(把棚架 的後部置於左右軌道上) 3沿著左右軌道將迴轉層架向外拉, 同時將迴轉層架的內側向下壓。(向 外拉的時候,請確保迴轉層架會在溝 3向上抬起迴轉層架,取出到雪 槽中間停住) 櫃外。(使其通過左右軌道) 1將拉桿移動到“鎖扣”的位置。 2將迴轉層架中央部位 限位器的鉤,按箭頭方 向旋轉,拆下限位器。 限位器 3把手伸進迴轉層架的 中央部位,向上抬起 托盤。 ※慢慢地提起托盤, 否則托盤會掉落。 4用雙手拆除托盤。 請按照圖示方向安裝托盤。如果以其他的方 向安裝會導致安裝不正確,部件 可能會掉落。 高度調節架(請勿拆解高度調節架,或使用潤滑脂等化學物品。否則可能造成故障。) 配件的拆卸方式與保養 拆除棚架 安裝棚架 1將拉桿完全推向右方。 1確保拉桿已完全推 向右方。 2逐次用力推起每個支撐物。 (4個支撐物) (鬆開時會聽到 “喀嚓”聲) 如果支撐物 不容易鬆開, 將內鉤向內推。 3取出到雪櫃外。 拆除托盤 1用手指將棚架後面的鉤(3個)拉向 前,同時將托盤向上推。 2確保4個金屬阻擋物已牢固地裝入, 然後輕力地將摺架裝入,4個支撐物 要對齊4個阻擋物。 3逐次將4個支撐物從上向下推。(會聽 到“喀嚓”聲。) 4將拉桿向左右兩邊推,檢查高度調節架 向上下移動時是否保持平行。(如果棚 架沒有保持平行,將高度調節架拆除, 並且重複步驟 1 至 4) 2將托盤後部向上推,直至前側的鉤 (3個)和兩側的鉤(2個)鬆開。 ※慢慢地提起托盤, 否則托盤會掉落。 3用雙手拆除托盤。 二變式靈活摺架 將摺架推入, 再稍微外拉, 向上抬起取出。 52 1 2 裝回時,請依照與拆卸時相反的 程序進行。 保養後/定期檢修 雪櫃的背面、地板 1卸下支撐腳蓋。 2 旋轉可調式支撐腳,使支撐腳懸空,移動雪櫃。 為防止劃傷地板,建議使用保護材料。 3 將背面、牆壁與地板的髒汙擦拭乾淨。由於空氣 黑斑、 對流的關係,雪櫃背面與地板 灰塵 比較容易堆積灰塵及出現髒汙。 打掃乾淨可以節電,請定期打掃。 4請確認地板上有無漏水。 電源插頭和電源線的檢查 為安全起見,請定期保養。 1從插座上把電源插頭拔下來檢查。 •電源插頭、電源線上有沒有損傷、發熱現象。 2用幹布擦掉電源插頭及周圍的灰塵。 3將電源插頭切實地插入插座。 警告 如果電源插頭、電源線有受損,或有灰塵堆積,可 能導致觸電或火災。 注意 請勿將手伸到雪櫃的下面,否則會導致受傷。 滑動微凍箱、小件箱 1完全拉出。 2向上抬起取出。 2 2 1 1 活動盤、瓶架 1 2 1 2 1交替提起左右兩邊。(活動盤及瓶架均牢固地安裝) 2向前拉出。 安裝時 ˙ 確認已經切實裝好。 (如果未裝到位,會掉落導致受傷) 1將室門向外拉到底 2向上抬起取出。 承水盤 配件的拆卸方式與保養 製冰室、自由切換室 將髒污、汁液與結露擦拭乾淨。 2 1 冷凍室、蔬菜室 蒸發盤 1左右兩側分別向內側壓, 同時向外拉,將 其卸下。 2雙手托著,輕輕拉出。 承水盤 2 1 1 (冷凍室)冷凍箱(上) (蔬菜室)滑動箱 1將室門向外拉到底 2向上抬起取出。 (冷凍室)冷凍箱(下) (蔬菜室)蔬菜箱 2 3將室門向外拉到底 4向上抬起取出。 4 1 3 53 特殊情況 狀況 停電時 移動時、 改變朝向時 長時間 不使用時 搬運時 請這樣解決 •請減少櫃門的開啟次數,避免再儲藏新的食品 •除了溫度調節以外,其他操控面板的設定會有變更的現象。敬請重新確認。(兒童按鍵鎖、省電和快速冷卻等) 1向上調節支撐腳。 第 2按前後方向移動。 35 頁 ※如果不按照前後方向推移,將會損壞地板。 3改變朝向時,請在滾輪及後部的支撐腳下部鋪上布片等保護地板,然後再改變朝向。 1清理自動製冰機。 第 50 頁 2拔出電源插頭,清理雪櫃內部後,將櫃門打開2~3天以便乾燥。 ※倘若未充分乾燥,則會滋生霉菌、出現異味、並因冷卻器腐蝕而導致冷媒漏氣。 1倒掉儲水槽及製冰盤內的冰塊與水。 第 49 頁 2穿上例如勞工手套的保護設備。 3拆除支撐腳蓋、向上調整支撐腳。 4拔出插頭。 5倒掉蒸發盤中的水。 第 52 頁 6由2個人以上,手持正面下方內側與背面上方,小心搬運。 •請勿平放(避免壓縮機故障) 正面下方 背面上方 內側 警告 因為使用的是可燃性冷媒,請勿損毀冷媒迴路。如果冷媒氣體滲漏出來,將可以導致燃燒或 爆炸。 1反復按 鍵,顯示 。 想把冷凍室 設定為低溫 冷凍時 2同時按住 鍵和 的蜂鳴聲)。 鍵約3秒(直至發出“嗶嗶” “冷凍室” 每10秒左右 閃爍1次。 3按 鍵,選擇 。 將冷凍室的溫度調節顯示調為非 ,或者按照2的方式操作。 除 To解 cancel ※設定為溫度微調模式,把冷凍室的溫度調節顯示選擇為 時,可以把冷凍室的溫度設定得更低一點。 特殊情況 雖然沒有操作按鍵,但是每隔 一定時間,所有顯示均閃爍3 次,或者操控面板的儲藏室顯 示或溫度調節顯示按順序反復 閃爍時(示範模式) •在這種模式下,雪櫃不製冷。請聯絡購買的經銷商,或者按照下述方法解除示範 模式。 示範模式的解除方法 1冷藏室門保持打開狀態。 2按2次 鍵。 3同時按 鍵和 鍵和 鍵約5秒。 41分鐘後確認顯示部是否還閃爍。 (還在閃爍時,示範模式還沒有被解除) 標記快速閃爍時(約每秒5 次)或蜂鳴聲沒有停止時 54 請迅速聯絡購買處的經銷商,或與客戶服務代表洽談。 •如果蜂鳴聲沒有停止,請按住“ICE SELECT”鍵5秒,直到蜂鳴聲停止。蜂鳴聲 停止後,請聯絡購買處的經銷商或三菱維修中心。 當冷藏室、冷凍室、自由切換室(溫度調節設定為“冷 凍”時),可以進行溫度微調。 •溫度微調時,儲藏室顯示約每10秒閃爍1次。 冷藏室、冷凍室 弱設定 第 設定為溫度微調模式 約為-12℃ 38 頁 重複上述操作。 第 執行溫度微調 38 頁 比“中”調高約 1.2℃ 比“中”調高約 比“中”調高約 0.3℃ 0.6℃ 1按 鍵,顯示出欲微調溫度的儲存室。 中設定 2重複按 鍵來調整溫度。 第 約為-15℃ 38 頁 第 40 頁 比“中”調低約 比“中”調低約 0.3℃ 0.6℃ 例:使冷藏室在“弱”的基礎 上調低0.6℃時 中強設定 “H” 閃爍 “REF”約每 10秒閃爍1次 40 頁 比“弱”調低約 比“弱”調低約 0.6℃ 1.2℃ 弱中設定 想微調溫度時 (溫度微調 模式) 第 比“弱”調低約 比“弱”調低約 0.3℃ 0.6℃ 同時按住 鍵和 鍵約3秒(直至發出 “嗶嗶”的蜂鳴聲)。 解除 自由切換室 (冷凍模式) 第 38 頁 比“中”調低約 1.2℃ 比“強”調高約 比“中”調低約 0.6℃ 1.8℃ 比“強”調高約 比“中”調低約 0.3℃ 2.4℃ ※右述設定僅為示例,實際情況下,根據食品的放置狀 態、櫃門的開閉頻率等使用狀態,溫度會與右述示例 有所不同。 注1) 在溫度微調模式中將冷凍室設定為 時的溫度, 比不設定溫度微調的溫度低。 強設定 注1) 第 約為-18℃ 38 頁 第 40 頁 規格 本雪櫃僅設計為香港使用,而不能 在任何其他國家使用。在香港以外 的地方不會提供任何維修服務。 配件 數量 型號 MR-B42S 冷藏室 1 二變式靈活摺架 1 滑動微凍箱 1 滑動微凍箱蓋 1 儲水槽(內附光學除菌除鉛濾網) 1 活動盤(大) 1 活動盤(小) 2 小件箱 1 活動雞蛋架 1 瓶架 1 儲冰箱 1 靜音墊 1 冰鏟 1 切換盒 1 鋁盤 1 冷凍箱(上) 1 冷凍箱(下) 1 蔬菜箱 1 滑動箱 1 蒸發盤 1 支撐腳蓋 1 自由 冷凍室 蔬菜室 切換室 1 高度調節架 規格 製冰室 迴轉層架 55 故障排除 特別是在剛開始使用時及夏季時諮詢較多的問題 操作方法等 雪櫃完全不冷! 操控面板的背景燈自行熄滅! •剛開始使用時,需要一定的時間才能冷 卻下來。夏季充分冷卻下來一般需要~24 小時。 •操控面板的顯示是否在閃爍? →示範模式: 第 54 頁 •電源插頭是否插好?斷路器是否被斷 開? •為了節電,持續約30秒不操作,背景 燈將自動熄滅。 第 37 頁 冰塊、食品有異味! •儲水槽每週打掃一次了嗎? 第 50 頁 •是否沒有密封包住容易發出味道的食 品? 第 45 頁 機體外側發熱! •剛安裝好或者在夏天,特別是機體外側 會發熱(約50~60℃)。這是因為機體 側面及頂部裝有散熱、防冷凝管道。這 是冷卻所必須的功能,不是什麼異常。 第 34 頁 •下麵有散熱用風扇,有風吹出。 狀況 雪櫃冷度不足 製冰量少 冰塊會融化 請確認 儲藏室的溫度調節是否設定為“L”? 是不是剛開始使用? 雪櫃是否不能正常散熱,例如雪櫃四周沒有留出 空間、雪櫃放置在直射陽光下等? 內部冷氣流動是否有受到阻礙?或者是不是頻繁 開門、雪櫃門有沒有關緊? 是不是剛剛開始使用? 無法製冰 儲水槽的水 不會減少 製冰花費很 長時間 給水泵和水管是否正確地安裝在儲水槽中? 給水管是否安裝至儲水槽? 儲冰箱內是否有放置食品或冰鏟等? 製冰室是否設定為“STOP”? 製冰室是否設定為“CRL”? 儲水槽內有足夠的水嗎?雪櫃傾斜放置嗎? 溫度設定是否設定至“H”? 故障排除 冷凍室以外的 食品結凍 水分多的食品是否放在棚架的深處? 周圍的溫度是否低於5℃以下? 溫度剛剛開始調整,或者剛開始使用雪櫃? 自由切換室的 食品開始融化 上部的食品放得太密嗎? 是否接觸到剛放入的熱的食品? 放入熱的食品時,是否按了超強冷凍按鍵? 霜淇淋、冷凍食品是不是按照“FZR•L”或者 “FZR•M”方式保存? 56 解決方式、原因 請設定為“M”或者“H”。 冷度約需4~5個小時才會足夠。夏天製冰甚至需要 24個小時。 第 34 頁 檢查安裝正確無誤。 請確認食品是否塞得太多?雪櫃門是否有關緊? 第 45 頁 冷度約需4~5個小時才會足夠。夏天製冰甚至需要 24個小時。 特別檢查儲水槽內的水管出口已牢固地安裝至儲 第 51 頁 水槽。 第 50 頁 檢查安裝。 電腦判斷“冰塊滿了”。請將儲冰箱中的食品等 取出。此外,也請將冰塊推平。 請設定為“REG”、“QCK”或“CRL”。 “CRL”時間比通常製冰時間長。(約5~8小時) 第 49 頁 有時一次製冰數會少點。 請設定為“M”。此外,速凍功能運轉時,雪櫃內 溫度會暫時降低。 豆腐、蔬菜、水果等水分含量較多的食品與飲 料,請放在外側。 請將冷藏室及蔬菜室的溫度調節設定為“L”,這 樣比較不容易結凍。 雪櫃需要時間冷卻。等待最少30分鐘之後再放入 食品,或使用速凍。 上部預留足夠的間隙,讓冷氣流動。 凍結食品與熱的食品接觸,會融化。 放入熱的食品後,請按下超強冷凍按鍵。這樣食 品溫度會迅速下降。 請設定為“FZR•H”。 請先依以下步驟確認,如果還有故障情況,請立刻洽詢 經銷商。 狀況 請確認 解決方式、原因 溫度無法調整 是否有顯示 ? 取消兒童按鍵鎖設定。 不能進行 超強冷凍 (燈不亮) 是不是儲藏室顯示為“VR”、溫度調節顯示為 “SOFT FZR”? 請在自由切換室的設定變為軟冷凍之後,按下超 強冷凍按鍵。只有自由切換室的設定在軟冷凍時 才能進行超強冷凍。 第 41 頁 按下了超強冷凍按鍵了嗎? 想進行超強冷凍的食品是不是沒有放在自由切換 室的最上部? 請按下超強冷凍按鍵。並確認顯示了超強冷凍。 因為要用光i-see感測器測量食品溫度,想進行超 強冷凍的食品必須放在自由切換室的最上部。 自由切換室的設定是不是剛剛改成“SOFT FZR”? 第 43 頁 先設定為SOFT FZR,等溫度穩定後(約2小時 後),進行超強冷凍。 第 41 頁 進行了 超強冷凍, 但是吃起來 味道不好。 冷凍室外側與內 側會結露水。 冷凍室內 會結霜。 水會低落 至地板。 櫃門容易自行 開啟 櫃門無法 關上 門開警告 發出蜂鳴聲 冰塊會突起 會連在一起 泛白變小融化 是否常常開雪櫃門,或是雪櫃門沒關緊? 是否為雨天,而且濕度較高? 檢查櫃門是否觸碰到食品?是否儲存過多食 品? 檢查拉門收納箱後方是否有食品掉落?確認櫃 門與本體之間是否有電線等異物卡在當中? 各項安裝是否確實?腳架是否確實抵住貼在地 面? 有關門開警告,請參閱第37、54頁。 參照第49頁有關冰塊的形狀及透明度。 第 36 頁 空氣中的濕氣冷卻時會有結露或結霜形成。雪櫃 門的小小縫隙,也會產生結露或結霜。露水會滴 在地板上。 第 45 頁 雪櫃會暫時出現結露現象。請用乾布擦拭。冷凍 室內容易有結霜出現。嘗試減少打開雪櫃門的時 間。 儲放時,請勿讓食品突出於收納箱或棚架。 請將夾在櫃門間的物品收拾乾淨。 調整可調式支撐腳,使雪櫃前方稍微提起,關門 時會較容易。 第 35 頁 第 37 頁 第 54 頁 第 49 頁 確認給水管是否確實安裝在儲水槽上?儲水槽與 給水管的連接部是否有異物附著? 確認製冰室或冷凍室儲存箱後方是否有食品或塑 膠掉落? 儲水槽或 給水管變暖 因為內建有防止結凍的加熱器。 並非異常現象。 電視等電器 會出現雜音 是否將雪櫃裝設在電視等電器產品的附近? 雪櫃的電源是否太靠近天線的連接線? 請將雪櫃裝設於遠離電視等電器產品的場所。 建議使用專用電源。 運轉聲音很大 有怪聲 以下幾種聲音 並非異常狀況。 運轉聲音突然變大或聲調改變。 在首次操作、氣溫變熱、雪櫃門頻密開關或速凍運 轉等時,雪櫃會切換至高速操作以產生有效冷卻。 自動製冰的聲音。即使儲水槽沒水,自動製冰機 與給水泵還是會每隔100分鐘左右發出聲音。 確認自動製冰機動作的聲音。在“STOP”狀態 下,還是會進行確認。 風扇馬達開始運轉的聲音。 冷媒(氣體)流動的聲音。 發出“嘎拉嘎拉、啾因”的聲音經常出現(每隔 1~2小時)。 發出“咕、啾因”的聲音,經常出現在插電後, 製冰停止時(每隔1~2小時)。 關閉雪櫃門時,發出“咻”的聲音。 發出“啾”或“噗嚕噗嚕”(沸騰音)的聲音經 常出現。 打開門時經常發出擊打水或水滴的聲音。 有時會有像蚊子一樣的“嗡”的聲音。 打開冷凍室門後有時會發出低沉的呼呼聲。 自由切換室的 藍色LED燈不亮 安裝未能確實或是因異物造成縫隙時,就會導致 冷氣逆流而產生結凍的現象。 冷氣向背面流動產生冷凍效果。取去掉落的食品 或塑膠。 第 50 頁 故障排除 儲水槽或 給水管出現 結凍現象 暖空氣流入雪櫃內,塑膠因膨脹而發出的聲音。 是調節風量的擋板或者自由切換室的光i-see感測器 動作的聲音。 這是冷卻風扇吹出氣流的聲音。 判定藍色LED是否有故障,請在打開自由切換室的門的狀態下,打開冷藏室的門,確認各個儲藏室的藍色LED 燈是否亮。自由切換室的藍色LED燈亮是正常現象。 57 MEMO MEMO ■ This appliance is designed for use in Hong Kong only and cannot be used in any other country. No servicing is available outside of Hong Kong. ■ This refrigerator uses flammable foaming gas for insulation. Please deliver the unit to specialized industrial waste dealer when you do away it. Please follow the rules in your country. ■ The appliance is not intended for use by young children or infirm persons without supervision. ■ Young children should be supervised to ensure that they do not play with the appliance. ■ WARNING - Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. WARNING - Do not use electrical appliances ■ inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. ■ WARNING - Just in case of having damaged the refrigerant circuit, do not use electric items or fire equipments near by, and open the window to ventilate the room. And contact the retail store at which you purchased it or the following MITSUBISHI SERVICE CENTER. ■ The refrigerator contains flammable refrigerant (R600a: iso-butane). ■ The refrigeration system behind and inside the refrigerator contains refrigerant. Do not allow any sharp objects to come into contact with the refrigeration system. Do not block the openings on the circumstances of ■ the refrigerator. ■ The user manual should be handed over to any person who would use or handle the refrigerator whenever the refrigerator would be transferred to another location and delivered to a recycling plant. ■ 本產品設計為僅供於香港使用,並不能於其 他國家使用。 於香港以外的其他國家並不提供維修服務。 ■ 本雪櫃使用易燃的泡沫氣體作隔熱之用。 棄掉本雪櫃時,請交給專業的工業廢物回收 商。 請按照您所在國家的法例處理。 ■ 本產品不適合幼童或體弱者在沒有監管的情 況下使用。 ■ 注意看管幼童,確保他們不會把玩本產品。 ■ 警告 — 除了製造商建議的方法外,請勿使用 機械裝置或其他方法加速解凍程序。 ■ 警告 — 除了製造商建議的電器類型外,請勿 在本產品的食物儲存室內使用其他電器。 ■ 警告 — 如果冷媒迴路已損毀,不要使用周圍 的電器用品或滅火設備,並開啟窗戶以使室 內空氣流通。請聯絡您購買本雪櫃的商店或 以下的三菱服務中心。 。 ■ 本雪櫃含有易燃的冷媒(R600a:異丁烷) ■ 雪櫃內部及背後的製冷系統含有冷媒,嚴禁 以任何尖銳物體接觸製冷系統。 ■ 不要堵塞雪櫃周圍的空間。 ■ 如果雪櫃要搬運到另一地方或交給回收商, 使用說明書亦應該與雪櫃一併交給處理和運 送的人士。 H E A D O F F I C E : T O K Y O B L D G . , 2 - 7 - 3 , M A R U N O U C H I , C H I Y O D A - K U , T O K Y O 1 0 0 - 8 3 1 0 , J A PA N 總公司:日本東京都丸之內東京大樓 直通電報 J24532,電報掛號 MELCO TOKYO SOLE AGENT in Hong Kong MITSUBISHI ELECTRIC RYODEN AIR-CONDITIONING & VISUAL INFORMATION SYSTEMS (HONG KONG) LIMITED 7/F., Manulife Tower, 169 Electric Road, North Point, Hong Kong. Head Office: Tel. 2510-1505 Service Center: Tel. 2427-8484 香港總代理 三菱電機菱電空調•影像設備(香港)有限公司 香港北角電氣道169號宏利保險中心7樓 電話 2510-1505 服務中心:電話 2427-8484 AZ79L115H01 Printed in Japan ">
/
डाउनलोड
बस एक दोस्ताना अनुस्मारक. आप दस्तावेज़ को यहीं देख सकते हैं. लेकिन सबसे महत्वपूर्ण बात, हमारे एआई ने इसे पहले ही पढ़ लिया है. यह जटिल चीजों को सरल शब्दों में समझा सकता है, किसी भी भाषा में आपके सवालों के जवाब दे सकता है और सबसे लंबे या सबसे जटिल दस्तावेजों को भी जल्दी से नेविगेट करने में आपकी मदद कर सकता है.
विज्ञापन