advertisement
AFBR-5701Z and AFBR-5705Z
Families of Multi-Mode Small Form Factor Pluggable (SFP) Optical
Transceivers with Optional DMI for Gigabit Ethernet (1.25 GBd) and
Fibre Channel (1.0625 GBd)
Data Sheet
Description
The AFBR-570xZ family of SFP optical transceivers offers the customer a wide range of design options, including optional DMI features (further described later), two temperature ranges (extended or industrial), and choice of standard or bail delatch. The AFBR-5705Z family targets those applications requiring DMI features. The
AFBR-5701Z family is a streamlined product designed for those applications where DMI features are not needed. Throughout this document, AFBR-570xZ will be used to refer collectively to the product family encompassing this entire range of product options.
Part Number Options
The AFBR-570xZ SFP family includes the following products:
Part Number DMI Temperature
AFBR-5701LZ No Extended
AFBR-5701PZ No
AFBR-5701ALZ No
Extended
Industrial
AFBR-5701APZ No
AFBR-5705LZ Yes
AFBR-5705PZ Yes
AFBR-5705ALZ Yes
AFBR-5705APZ Yes
Industrial
Extended
Extended
Industrial
Industrial
Latch
Standard
Bail
Standard
Bail
Standard
Bail
Standard
Bail
* Extended Temperature Range is -10 to 85 °C
Industrial Temperature Range is -40 to 85 ° C
Related Products
• AFBR-5715Z family: 1.25 GBd Ethernet (1000BASE-SX)
SFP with DMI
• AFBR-5710Z family : 1.25 GBd Ethernet (1000BASE-SX)
SFP without DMI
• AFCT-5705Z family: 1.25 GBd Ethernet (1000BASE-LX) &
1.0265 GBd Fiber-Channel SFP with DMI
• AFCT-5701Z family: 1.25 GBd Ethernet (1000BASE-LX) &
1.0265 GBd Fiber-Channel SFP without DMI
Features
• ROHS-6 Compliant
• Compliant to IEEE 802.3 Gigabit Ethernet (1.25GBd)
1000BaseSX & Fiber Channel FC-PI 100-M5-SN-I & 100-
M6-SN-I
• Optional Digital Diagnostic Monitoring available
- AFBR-5701Z family: without DMI
- AFBR-5705Z family: with DMI
• Per SFF-8472, diagnostic features on AFBR-5705Z family enable Diagnostic Monitoring Interface for optical transceivers with real-time monitoring of:
- Transmitted optical power
- Received optical power
- Laser bias current
- Temperature
- Supply voltage
• Transceiver specifications according to SFP Multi-Source
Agreement (SFF-8074i) and SFF-8472, Revision 9.3
• Manufactured in an ISO 9001 compliant facility
• Hot-pluggable
• Temperature options
- (Extended) -10°C to +85°C
- (Industrial) -40°C to +85°C
• +3.3 V DC power supply
• Industry leading EMI performance for high port density
• 850 nm Vertical Cavity Surface Emitting Laser (VCSEL)
• Eye safety certified
• LC-Duplex fiber connector compliant
Applications
• Ethernet Switch
• Enterprise Router
• Broadband aggregation and wireless infrastructure
• Storage applications including Fiber Channel and iSCSCI
OPTICAL INTERFACE
LIGHT FROM FIBER
RECEIVER
PHOTO-DETECTOR
AMPLIFICATION
& QUANTIZATION
ELECTRICAL INTERFACE
RD+ (RECEIVE DATA)
RD— (RECEIVE DATA)
Rx LOSS OF SIGNAL
CONTROLLER & MEMORY
MOD-DEF2 (SDA)
MOD-DEF1 (SCL)
MOD-DEF0
LIGHT TO FIBER
TRANSMITTER
VCSEL
LASER
DRIVER &
SAFETY
CIRCUITRY
TX_DISABLE
TD+ (TRANSMIT DATA)
TD— (TRANSMIT DATA)
TX_FAULT
Figure 1. SFP Block Diagram
Overview
The AFBR-570xZ family of optical transceivers are compliant with the specifications set forth in the
IEEE802.3 (1000BASE-SX), Fibre Channel (100-M5-SN-I,
100-M6-SN-I), and the Small Form-Factor Pluggable
(SFP) Multi-Source Agreement (MSA). This family of transceivers is qualified in accordance with Telcordia
GR-468-CORE. Its primary application is servicing Gigabit
Ethernet and Fibre Channel links between optical networking equipment.
The AFBR-570xZ offers maximum flexibility to designers, manufacturers, and operators of Gigabit Ethernet networking equipment. A pluggable architecture allows the module to be installed into MSA standard SFP ports at any time – even with the host equipment operating and online.
This facilitates the rapid configuration of equipment to precisely the user’s needs – reducing inventory costs and network downtime. Compared with traditional transceivers, the size of the Small Form Factor package enables higher port densities.
Module Diagrams
Figure 1 illustrates the major functional components of the
AFBR-570xZ. The external configuration of the module is depicted in Figure 7. Figure 8 depicts the panel and host board footprints.
20 V
EE
T
19 TD–
18 TD+
17 V
EE
T
16 V
CC
T
15 V
CC
R
14 V
EE
R
13 RD+
12 RD–
11 V
EE
R
TOP OF BOARD
3 2 1
ENGAGEMENT
SEQUENCE
1 V
EE
T
2 TX FAULT
3 TX DISABLE
4 MOD-DEF(2)
5 MOD-DEF(1)
6 MOD-DEF(0)
7 RATE SELECT
8 LOS
9
10
V
EE
R
V
EE
R
3 2 1
BOTTOM OF BOARD
(AS VIEWED THROUGH TOP OF BOARD)
Figure 2. Pin description of the SFP electrical interface.
2
Installation
The AFBR-570xZ can be installed in or removed from any
MSA-compliant Pluggable Small Form Factor port regardless of whether the host equipment is operating or not. The module is simply inserted, electrical-interface first, under finger-pressure. Controlled hot-plugging is ensured by 3-stage pin sequencing at the electrical interface. This printed circuit board card-edge connector is depicted in
Figure 2.
As the module is inserted, first contact is made by the housing ground shield, discharging any potentially component-damaging static electricity. Ground pins engage next and are followed by Tx and Rx power supplies.
Finally, signal lines are connected. Pin functions and sequencing are listed in Table 2.
Transmitter Section
The transmitter section includes the Transmitter Optical
Subassembly (TOSA) and laser driver circuitry. The TOSA, containing an 850 nm VCSEL (Vertical Cavity Surface
Emitting Laser) light source, is located at the optical interface and mates with the LC optical connector. The
TOSA is driven by a custom IC, which converts differential logic signals into an analog laser diode drive current. This
Tx driver circuit regulates the optical power at a constant level provided the data pattern is DC balanced (8B10B code for example).
Transmit Disable (Tx_Disable)
The AFBR-570xZ accepts a TTL and CMOS compatible transmit disable control signal input (pin 3) which shuts down the transmitter optical output. A high signal implements this function while a low signal allows normal transceiver operation. In the event of a fault (e.g. eye safety circuit activated), cycling this control signal resets the module as depicted in Figure 6. An internal pull-up resistor disables the transceiver transmitter until the host pulls the input low. Host systems should allow a 10ms interval between successive assertions of this control signal.
Tx_Disable can also be asserted via the 2-wire serial interface (address A2h, byte 110, bit 6) and monitored
(address A2h, byte 110, bit 7).
The contents of A2h, byte 110, bit 6 are logic OR’d with hardware Tx_Disable (pin 3) to control transmitter operation.
Transmit Fault (Tx_Fault)
A catastrophic laser fault will activate the transmitter signal,
TX_FAULT, and disable the laser. This signal is an open collector output (pull-up required on the host board). A low signal indicates normal laser operation and a high signal indicates a fault. The TX_FAULT will be latched high when a laser fault occurs and is cleared by toggling the
TX_DISABLE input or power cycling the transceiver. The transmitter fault condition can also be monitored via the
2-wire serial interface (address A2, byte 110, bit 2).
Eye Safety Circuit
The AFBR-570xZ provides Class 1 eye safety by design and has been tested for compliance with the requirements listed in Table 1. The eye safety circuit continuously monitors optical output power levels and will disable the transmitter and assert a TX_FAULT signal upon detecting an unsafe condition. Such unsafe conditions can be created by inputs from the host board (Vcc fluxuation, unbalanced code) or faults within the module.
Receiver Section
The receiver section includes the Receiver Optical
Subassembly (ROSA) and amplification/quantization circuitry. The ROSA, containing a PIN photodiode and custom trans-impedance preamplifier, is located at the optical interface and mates with the LC optical connector.
The ROSA is mated to a custom IC that provides postamplification and quantization. Also included is a Loss Of
Signal (LOS) detection circuit.
Receiver Loss of Signal (Rx_LOS)
The Loss Of Signal (LOS) output indicates an unusable optical input power level. The Loss Of Signal thresholds are set to indicate a definite optical fault has occurred
(e.g., disconnected or broken fiber connection to receiver, failed transmitter, etc.).
The post-amplification IC includes transition detection circuitry which monitors the ac level of incoming optical signals and provides a TTL/CMOS compatible status signal to the host (pin 8). An adequate optical input results in a low Rx_LOS output while a high Rx_LOS output indicates an unusable optical input. The Rx_LOS thresholds are factory-set so that a high output indicates a definite optical fault has occurred. For the AFBR-5705Z family, Rx_LOS can also be monitored via the 2-wire serial interface (address A2h, byte 110, bit 1).
3
Functional I/O
The AFBR-570xZ accepts industry standard differential signals such as LVPECL and CML within the scope of the
SFP MSA. To simplify board requirements, transmitter bias resistors and ac coupling capacitors are incorporated, per SFF-8074i, and hence are not required on the host board. The module is AC-coupled and internally terminated.
Figure 3 illustrates a recommended interface circuit to link the AFBR-570xZ to the supporting Physical Layer integrated circuits.
Timing diagrams for the MSA compliant control signals implemented in this module are depicted in Figure 6.
The AFBR-570xZ interfaces with the host circuit board through twenty I/O pins (SFP electrical connector) identified by function in Table 2. The AFBR-570xZ high speed transmit and receive interfaces require SFP MSA compliant signal lines on the host board. The Tx_Disable,
Tx_Fault, and Rx_LOS lines require TTL lines on the host board (per SFF-8074i) if used. If an application chooses not to take advantage of the functionality of these pins, care must be taken to ground Tx_Disable (for normal operation).
Digital Diagnostic Interface and Serial Identification
(EEPROM)
The entire AFBR-570xZ family complies with the SFF-
8074i SFP specification. The AFBR-5705Z family further complies with SFF-8472, the SFP specification for Digital
Diagnostic Monitoring Interface. Both specifications can be found at http://www.sffcommittee.org.
The AFBR-570xZ features an EEPROM for Serial ID, which contains the product data stored for retrieval by host equipment. This data is accessed via the 2-wire serial
EEPROM protocol of the ATMEL AT24C01A or similar, in compliance with the industry standard SFP Multi-Source
Agreement. The base EEPROM memory, bytes 0-255 at memory address 0xA0, is organized in compliance with
SFF-8074i. Contents of this serial ID memory are shown in Table 10.
VCCT,R
10 µF 0.1 µF
1 µH
1 µH
GP04
TX_FAULT
VREFR
TBC
EWRAP
MAC
ASIC
RBC
RX_RATE
RX_LOS
GPIO(X)
GPIO(X)
GP14
REFCLK
125 MHz
*RES
0.1
µF
SO1+
TX[0:9]
SYNC
LOOP
AVAGO
HDMP-1687
RX[0:9]
SO1–
SYN1
RC1(0:1)
RCM0
RFCT
SI1+
SI1–
VCCT,R
R
*RES
50
50
50
50
Ω
Ω
Ω
Ω
*RES *RES
10
µF
*RES
0.1
µF
HOUSING
GROUND
VCCT
*RES
AVAGO
AFBR-570xZ
TX_DISABLE
TX_FAULT
TD+
C
C
R
VEET
TD–
LASER DRIVER
& EYE SAFETY
CIRCUITRY
VCCR
RD+
C
C
RD–
AMPLIFICATION
&
QUANTIZATION
REF_RATE
RX_LOS
MOD_DEF2
MOD_DEF1
MOD_DEF0
VEER
EEPROM
NOTE: * 4.7 k
Ω < RES < 10 kΩ
Figure 3. Typical application configuration.
4
As an enhancement to the conventional SFP interface defined in SFF-8074i, the AFBR-5705Z family is compliant to SFF-8472 (digital diagnostic interface for optical transceivers). This new digital diagnostic information is stored in bytes 0-255 at memory address 0xA2.Using
the 2-wire serial interface defined in the MSA, the AFBR-
5705Z provides real time temperature, supply voltage, laser bias current, laser average output power and received input power. These parameters are internally calibrated, per the MSA.
The digital diagnostic interface also adds the ability to disable the transmitter (TX_DISABLE), monitor for
Transmitter Faults (TX_FAULT), and monitor for Receiver
Loss of Signal (RX_LOS).
The new diagnostic information provides the opportunity for Predictive Failure Identification,
Compliance Prediction, Fault Isolation and Component
Monitoring.
Predictive Failure Identification
The predictive failure feature allows a host to identify potential link problems before system performance is impacted. Prior identification of link problems enables a host to service an application via “fail over” to a redundant link or replace a suspect device, maintaining system uptime in the process. For applications where ultra-high system uptime is required, a digital SFP provides a means to monitor two real-time laser metrics associated with observing laser degradation and predicting failure: average laser bias current (Tx_Bias) and average laser optical power (Tx_Power).
Compliance Prediction
Compliance prediction is the ability to determine if an optical transceiver is operating within its operating and environmental requirements. AFBR-5705Z devices provide real-time access to transceiver internal supply voltage and temperature, allowing a host to identify potential component compliance issues. Received optical power is also available to assess compliance of a cable plant and remote transmitter. When operating out of requirements, the link cannot guarantee error free transmission.
Fault Isolation
The fault isolation feature allows a host to quickly pinpoint the location of a link failure, minimizing downtime. For optical links, the ability to identify a fault at a local device, remote device or cable plant is crucial to speeding service of an installation. AFBR-5705Z realtime monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power can be used to assess local transceiver current operating conditions. In addition, status flags
Tx_Disable and Rx Loss of Signal (LOS) are mirrored in memory and available via the two-wire serial interface.
Component Monitoring
Component evaluation is a more casual use of the
AFBR-5705Z real-time monitors of Tx_Bias, Tx_Power,
Vcc, Temperature and Rx_Power. Potential uses are as debugging aids for system installation and design, and transceiver parametric evaluation for factory or field qualification. For example, temperature per module can be observed in high density applications to facilitate thermal evaluation of blades, PCI cards and systems.
Required Host Board Components
The MSA power supply noise rejection filter is required on the host PCB to meet data sheet performance. The
MSA filter incorporates an inductor which should be rated 400 mADC and 1
Ω series resistance or better. It should not be replaced with a ferrite. The required filter is illustrated in Figure 4.
The MSA also specifies that 4.7 K to 10 K
Ω pull-up resistors for TX_FAULT, LOS, and MOD_DEF0,1,2 are required on the host PCB.
1 µH
V
CC
T
0.1 µF
V
CC
R
0.1 µF 10 µF
SFP MODULE
Figure 4. MSA required power supply filter.
HOST BOARD
1 µH
0.1 µF 10 µF
3.3 V
5
Fiber Compatibility
The AFBR-570xZ transciever is capable of transmission at 2 to 550 meters with 50/125 µm fiber, and at 2 to
275 meters with 62.5 125 µm fiber, for 1.25 GBd
Ethernet. It is capable of transmission up to 500m with
50/125 µm fiber and up to 300m with 62.5/125 µm fiber, for 1.0625 GBd Fiber Channel.
Application Support
To assist in the transceiver evaluation process, Agilent offers a 1.25 Gbd Gigabit Ethernet evaluation board which facilitates testing of the AFBR-570xZ. It can be obtained through the Agilent Field Organization by referencing Agilent part number HFBR-0571.
A Reference Design including the AFBR-570xZ and the
HDMP-1687 GigaBit Quad SerDes is available. It may be obtained through the Agilent Field Sales organization.
Regulatory Compliance
See Table 1 for transceiver Regulatory Compliance.
Certification level is dependent on the overall configuration of the host equipment. The transceiver performance is offered as a figure of merit to assist the designer.
Electrostatic Discharge (ESD)
The AFBR-570xZ exceeds typical industry standards and is compatible with ESD levels found in typical manufacturing and operating environments as described in Table 1.
There are two design cases in which immunity to ESD damage is important.
The first case is during handling of the transceiver prior to insertion into the transceiver port. To protect the transceiver, it’s important to use normal ESD handling precautions. These precautions include using grounded wrist straps, work benches, and floor mats in ESD controlled areas. The ESD sensitivity of the AFBR-570xZ is compatible with typical industry production environments.
The second case to consider is static discharges to the exterior of the host equipment chassis after installation.
To the extent that the optical interface is exposed to the outside of the host equipment chassis, it may be subject to system-level ESD requirements.
Electromagnetic Interference (EMI)
Equipment using the AFBR-570xZ family of transceivers is typically required to meet the requirements of the
FCC in the United States, CENELEC EN55022 (CISPR 22) in Europe, and VCCI in Japan.
The metal housing and shielded design of the AFBR-
570xZ minimize the EMI challenge facing the host equipment designer.
EMI Immunity
Equipment hosting AFBR-570xZ modules will be subjected to radio-frequency electromagnetic fields in some environments. The transceiver has excellent immunity to such fields due to its shielded design.
Flammability
The AFBR-570xZ transceiver is made of metal and high strength, heat resistant, chemically resistant, and UL
94V-0 flame retardant plastic.
Customer Manufacturing Processes
This module is pluggable and is not designed for aqueous wash, IR reflow, or wave soldering processes.
6
Table 1. Regulatory Compliance
Feature
Electrostatic Discharge
(ESD)to the Electrical Pins
Electrostatic Discharge
(ESD) to the Duplex LC
Reseptacle
Test Method
JEDEC/EIA
JESD22-A114-A
Variation of IEC 6100-4-2
Performance
Class 2 (> +2000 Volts)
Electromagnetic
Interference(EMI)
Immunity
FCC Class B CENELEC EN55022
Class B (CISPR 22A) VCCI Class 1
Variation of IEC 61000-4-3
Typically withstands at least 25 kV without damage when the duplex LC connector receptacle is contacted by a Human Body
Model probe
Applications with high SFP port counts are expected to be compliant; however, margins are dependent on customer board and chassis design.
Typically shows a negligible effect from a 10
V/m field swept from 80 to 1000 MHz applied to the transceiver without a chassis enclosure.
CDRH certification #9720151-57
TUV file R 72050685
UL File #E173874
Eye Safety
Component Recognition Underwriters Laboratories and Canadian
Standards Association Joint Component
Recognition for Information Technology
Equipment Including Electrical Business
Equipment
ROHS Compliance
US FDA CDRH AEL Class 1
EN(IEC)60825-1,2, EN60950 Class 1
Less than 1000ppm of: cadmium, lead, mercury, hexavalent chromium, polybrominated biphenyls, and polybrominated biphenyl ethers.
Caution
There are no user serviceable parts nor any maintenance required for the AFBR-570xZ. All adjustments are made at the factory before shipment to our customers. Tampering with, modifying, misusing or improperly handling the AFBR-570xZ will void the product warranty. It may also result in improper operation of the AFBR-570xZ circuitry, and possible overstress of the laser source. Device degradation or product failure may result. Connection of the AFBR-
570xZ to a non-Gigabit Ethernet compliant or non-Fiber
Channel compliant optical source, operating above the recommended absolute maximum conditions or operating the AFBR-570xZ in a manner inconsistent with its design and function may result in hazardous radiation exposure and may be considered an act of modifying or manufacturing a laser product. The person(s) performing such an act is required by law to re-certify and re-identify the laser product under the provisions of U.S. 21 CFR (Subchapter J).
7
Table 2. Pin Description
Pin Name
7
8
5
6
3
4
1
2
9
10
11
12
13
14
15
16
17
18
19
20
VeeR
VccR
VccT
VeeT
TD+
TD-
VeeT
Function/Description
VeeR
VeeR
VeeR
RD-
RD+
VeeT
TX Fault
TX Disable
MOD-DEF2
Transmitter Ground
Transmitter Fault Indication
Transmitter Disable - Module disables on high or open
Module Definition 2 - Two wire serial ID interface
MOD-DEF1
MOD-DEF0
Module Definition 1 - Two wire serial ID interface
Module Definition 0 - Grounded in module
Rate Selection Not Connected
LOS Loss of Signal
Receiver Ground
Receiver Ground
Receiver Ground
Inverse Received Data Out
Received Data Out
Reciver Ground
Receiver Power -3.3 V ±5%
Transmitter Power -3.3 V ±5%
Transmitter Ground
Transmitter Data In
Inverse Transmitter Data In
Transmitter Ground
Engagement
Order(insertion)
3
3
3
3
3
3
1
3
1
1
1
3
3
1
2
2
1
3
3
1
Notes
1
2
3
3
3
4
5
5
6
6
7
7
Notes:
1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7K
Ω – 10 KΩ resistor on the host board to a supply
<VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.
2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 K
Ω resistor.
Low (0 – 0.8 V): Transmitter on
Between (0.8 V and 2.0 V):
High (2.0 – 3.465 V):
Undefined
Transmitter Disabled
Open: Transmitter Disabled
3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7-10 K
Ω resistor on the host board to a supply less than
VccT +0.3 V or VccR+0.3 V.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is clock line of two wire serial interface for optional serial ID
Mod-Def 2 is data line of two wire serial interface for optional serial ID
4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 K – 10 K
Ω resistor on the host board to a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates normal operatio0n. In the low state, the output will be pulled to < 0.8 V.
5. RD-/+: These are the differential receiver outputs. They are AC coupled 100
Ω differential lines which should be terminated with 100 Ω differential at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines must be between 370 and 2000 mV differential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv differential.
6. VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.135 – 3.465 V at the SFP connector pin. The in-rush current will typically be no more than 30 mA above steady state supply current after 500 nanoseconds.
7. TD-/+: These are the differential transmitter inputs. They are AC coupled differential lines with 100
Ω differential termination inside the module. The
AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 –
1200 mV single ended). However, the applicable recommended differential voltage swing is found in Table 5.
8
Table 3. Absolute Maximum Ratings
Parameter
Ambient Storage Temperature(Nonoperating)
Case Temperature
Relative Humidity
Symbol
Ts
T
C
RH
Minimum
-40
-40
5
Maximum
+100
+85
95
Unit
°C
°C
%
Notes
1, 2
1, 2
1
Supply Voltage
Low Speed Input Voltage
V
CCT,R
V
IN
-0.5
-0.5
3.8
V
CC
+0.5
V
V
1, 2, 3
1
Notes:
1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded. See Reliability Data Sheet for specific reliability performance.
2. Between Absolute Maximum Ratings and the Recommended Operating Conditions functional performance is not intended, device reliability is not implied, and damage to the device may occur.
3. The module supply voltages, V
CC
T and V
CC
R, must not differ by more than 0.5V or damage to the device may occur.
Table 4. Recommended Operating Conditions
Parameter
Case Temperature
AFBR-570xLZ/PZ
AFBR-570xALZ/APZ
Supply Voltage
Data Rate
Symbol
T
T
V
C
C
CC
Minimum
-10
-40
3.135
1.0625
Typical
25
25
3.3
Maximum
85
85
3.465
1.25
Unit
°C
°C
V
Gb/s
Notes:
1. Recommended Operating Conditions are those within which functional performance within data sheet characteristics is intended.
2. Refer to the Reliability Data Sheet for specific reliability performance predictions.
3. IEEE802.3 Gigabit Ethernet.
4. ANSIX3.230 (FC-PI).
Notes
1, 2
1, 2
1
1,3, 4
9
Table 5. Transceiver Electrical Characteristics
Parameter
Module Supply Current
Power Dissipation
Power Supply Noise
Rejection(peak-peak)
Data input:
Transmitter Differential Input
Voltage (TD +/-)
Data Output:
Receiver Differential Output
Voltage (RD +/-)
V
V
I
O
Receive Data Rise & Fall Times T
RF
Low Speed Outputs:
Transmit Fault (TX_FAULT) Loss of Signal (LOS), MOD_DEF2
V
OH
V
OL
Low Speed Inputs:
Transmitter Disable
(TX_DISABLE), MOD_DEF 1,
MOD_DEF 2
V
IH
V
IL
Symbol
I
CC
P
DISS
PSNR
Minimum
500
370
2.0
0
2.0
0
Typical
160
530
100
1500
220
Maximum
220
765
2400
2000
Unit mA mW mV
PP mV mV
V
CC
T,R+0.3
V
0.8
V
CC
0.8
Notes:
1. Measured at the input of the required MSA Filter on host board.
2. Internally AC coupled and terminated to 100
Ω differential load.
3. Internally AC coupled, but requires a 100
Ω differential termination at or internal to Serializer/Deserializer.
4. Pulled up externally with a 4.7-10 K
Ω resistor on the host board to V
CC
T,R.
5. Mod_Def1 and Mod_Def2 must be pulled up externally with a 4.7-10 K
Ω resistor on the host board to V
CC
T,R.
ps
V
V
V
PP
PP
Notes
1
2
3
4
5
10
Table 6. Transmitter Optical Characteristics
Parameter
Output Optical Power (Average)
Optical Extinction Ratio
Center Wavelength
Spectral Width - rms
Optical Rise/Fall Time (1.25GBd)
Optical Rise/Fall Time (1.0625GBd)
Relative Intensity Noise
Total Jitter
(TP1 to TP2 Contribution 1.25 GBd)
(TP1 to TP2 contribution 1.0625 GBd)
Symbol Minimum Typical
P
OUT
-9.5
-6.5
9 12 ER
λ
C
σ
T
RISE
/
FALL
T
RISE
/
FALL
RIN
830 850
150
150
TJ
Deterministic Jitter
(TP1 to TP2 Contribution 1.0625 GBd)
DJ
Pout TX_DISABLE Assorted
Optical Modulation Amplitude
P
OFF
OMA 156
Notes:
1. IEEE 802.3.
2. Max. Pout is the lesser of 0 dBm or Maximum allowable per Eye Safety Standard.
3. 50/125 µm fiber with NA = 0.2, 62.5/125 µm fiber with NA = 0.275.
4. ANSIX3.230 (FC-PI).
130
0
NORMALIZED TIME (UNIT INTERVAL)
0.22
0.375
0.625
0.78
1.0
1.30
100
80
1.00
0.80
50 0.50
20 0.20
0 0
–20
0 22 37.5
62.5
78
NORMALIZED TIME (% OF UNIT INTERVAL)
100
–0.20
Figure 5a. Gigabit Ethernet transmitter eye mask diagram
260
300
-117
227
0.284
252
0.267
85
0.09
-35
Maximum Unit
-3 dBm
860 dB nm
0.85
nm ps
UI ps
UI ps ps dB/Hz ps
UI dBm
µW
Figure 5b. Typical AFBR-570xZ eye mask diagram
1
1,4
1
4
4
1
1
1
4
4
4
1
1
Notes
1,2,3
1
11
Table 7. Receiver Optical Characteristics
Parameter
Optical Input Power
Receiver Sensitivity
(Optical Input Power)
Stressed Receiver Sensitivity
1.25GBd(GBE)
Stressed Receiver Sensitivity
1.0625GBd (FC-PI) OMA
Symbol
P
R
P
RMIN
Total Jitter
(TP3 to TP4 Contribution 1.25GBd)
TJ
Total Jitter
(TP3 to TP4 Contribution 1.0625GBd)
TJ
Deterministic Jitter
(TP3 to TP4 Contribution 1.0625GBd)
DJ
Return Loss
LOS De-Asserted
LOS Asserted
LOS Hysterisis
Optical Modulation Amplitude
Notes:
1. IEEE 802.3.
2. 62.5/125 µm fiber.
3. 50/125 µm fiber.
4. ANSIX3.230 (FC-PI).
P
D
P
A
P
D
-P
A
OMA
67
55
-
-30
31
Minimum
-17
Typical
-21
3
266
0.332
205
0.218
113
0.12
-12
-17
Maximum
0
-17
-12.5
-13.5
Unit dBm dBm
UI ps
UI ps dBm dBm
µW
µW ps
UI dB dBm dBm dB
µW
1,2
1,3
2,4
3,4
4
1
4
4
1
1
4
1
1
1
4
Notes
1
1
12
Table 8. Transceiver SOFT DIAGNOSTIC Timing Characteristics
Parameter
Hardware TX_DISABLE Assert Time
Hardware TX_DISABLE Negate Time
Time to initialize, including reset of TX_FAULT
Hardware TX_FAULT Assert Time
Hardware TX_DISABLE to Reset
Hardware RX_LOS Assert Time
Hardware RX_LOS De-Assert Time
Software TX_DISABLE Assert Time
Software TX_DISABLE Negate Time
Software Tx_FAULT Assert Time
Software Rx_LOS Assert Time
Software Rx_LOS De-Assert Time
Analog parameter data ready
Serial bus hardware ready
Write Cycle Time
Serial ID Clock Rate
Symbol t_off t_on t_init t_fault t_reset t_loss_on t_loss_off t_off_soft t_on_soft t_fault_soft t_loss_on_soft t_loss_off_soft t_data t_serial t_write f_serial_clock
Minimum
10
Maximum
10
1
300
100
100
100
100
100
100
100
100
1000
300
10
400
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured from falling clock edge after stop bit of write transaction.
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of nominal.
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1-8 byte write command.
ms ms ms ms ms
µs
µs
µs
µs ms ms
Unit
µs ms ms ms kHz
Note 8
Note 9
Note 10
Note 11
Note 12
Note 13
Note 14
Note 15
Notes
Note 1
Note 2
Note 3
Note 4
Note 5
Note 6
Note 7
13
Table 9. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
Parameter
Accuracy
Symbol Min.
Units Notes
Transceiver Internal Temperature T
INT
±3.0
˚C Temperature is measured internal to the transceiver.
Valid from = -40 ˚C to 85 ˚C case temperature.
Transceiver Internal Supply
Voltage Accuracy
V
INT
±0.1
V
±10 %
Supply voltage is measured internal to the transceiver and can, with less accuracy, be correlated to voltage at the SFP Vcc pin. Valid over 3.3 V ±5%.
I
INT
is better than ±10% of the nominal value.
Transmitter Laser DC Bias Current I
INT
Accuracy
P
T
Transmitted Average Optical
Output Power Accuracy
Received Average Optical Input
Power Accuracy
P
R
±3.0
±3.0
dB dB
Coupled into 50/125
Valid from
µm multi-mode fiber.
100
µW to 500 µW, avg.
Coupled from 50/125 µm multi-mode fiber.
Valid from 31 µW to 500 µW, avg.
V
CC
> 3.15 V
TX_FAULT
TX_DISABLE
TRANSMITTED SIGNAL
V
CC
> 3.15 V
TX_FAULT
TX_DISABLE
TRANSMITTED SIGNAL t_init t_init t-init: TX DISABLE NEGATED t-init: TX DISABLE ASSERTED
V
CC
> 3.15 V
TX_FAULT
TX_DISABLE
TRANSMITTED SIGNAL t_init
INSERTION t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED
OCCURANCE OF FAULT
TX_FAULT
TX_DISABLE
TRANSMITTED SIGNAL t_fault t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED
TX_FAULT
TX_DISABLE
TRANSMITTED SIGNAL t_off t-off & t-on: TX DISABLE ASSERTED THEN NEGATED t_on
OCCURANCE OF FAULT
TX_FAULT
TX_DISABLE
TRANSMITTED SIGNAL
* SFP SHALL CLEAR TX_FAULT IN
t_init IF THE FAILURE IS TRANSIENT t_reset t_init* t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED
OCCURANCE OF FAULT
TX_FAULT
TX_DISABLE
TRANSMITTED SIGNAL t_reset
* SFP SHALL CLEAR Tx_FAULT IN
t_init IF THE FAILURE IS TRANSIENT t-fault2: TX DISABLE ASSERTED THEN NEGATED,
TX SIGNAL NOT RECOVERED
NOTE: t_fault2 timing is typically 1.7 to 2 ms.
t_fault2 t_init*
OPTICAL SIGNAL
OCCURANCE OF LOSS
LOS t-loss-on & t-loss-off
Figure 6. Transceiver timing diagrams (Module installed except where noted).
t_loss_on t_loss_off
14
Table 10. EEPROM Serial ID Memory Contents, Page A0h
18
19
20
21
22
23
11
12
13
8
9
10
14
15
16
17
24
25
26
27
28
4
5
6
7
1
2
3
Byte # Data
Decimal Hex
0 03
04
07
00
00
00
01
20
4F
20
20
20
20
00
00
41
56
41
47
01
0C
00
40
0C
01
00
00
37
1B
Notes
SFP physical device
SFP function defined by serial ID only
LC optical connector
1000BaseSX
Intermediate distance (per FC-PI)
Shortwave laser without OFC (open fiber control)
Multi-mode 50 m and 62.5 m optical media
100 Mbytes/sec FC-PI speed [1]
Compatible with 8B/10B encoded data
1200Mbps nominal bit rate (1.25Gbps)
550m of 50/125
µm fiber @ 1.25Gbps (Note 2)
275m of 62.5/125
µm fiber @ 1.25Gbps (Note 3
'A' - Vendor Name ASCII character
"V" - Vendor Name ASCII character
"A" - Vendor Name ASCII character
"G"- Vendor Name ASCII character
"O" - Vendor Name ASCII character
" " - Vendor Name ASCII character
" " - Vendor Name ASCII character
" " - Vendor Name ASCII character
" " - Vendor Name ASCII character
61
62
63
64
65
55
56
57
58
59
60
48
49
50
45
46
47
51
52
53
54
41
42
43
44
38
39
40
Byte # Data
Decimal Hex
37 00
17
6A
41
46
42
52
2D
35
37
30
20
20
20
20
20
20
20
20
03
52
00
00
1A
Notes
Vendor OUI (Note 4)
Vendor OUI (Note 4)
Vendor OUI (Note 4)
"A" - Vendor Part Number ASCII character
"F" - Vendor Part Number ASCII character
"B" - Vendor Part Number ASCII character
"R" - Vendor Part Number ASCII character
"-" - Vendor Part Number ASCII character
"5" - Vendor Part Number ASCII character
"7" - Vendor Part Number ASCII character
"0" - Vendor Part Number ASCII character
Note 5
Note 5
Note 5
Note 5
" " - Vendor Part Number ASCII character
" " - Vendor Part Number ASCII character
" " - Vendor Part Number ASCII character
" " - Vendor Part Number ASCII character
" " - Vendor Revision Number ASCII character
" " - Vendor Revision Number ASCII character
" " - Vendor Revision Number ASCII character
" " - Vendor Revision Number ASCII character
Hex Byte of Laser Wavelength (Note 6)
Hex Byte of Laser Wavelength (Note 6)
Checksum for bytes 0-62 (Note 7)
Hardware SFP TX_DISABLE, TX_FAULT,
& RX_LOS
29
30
31
32
33
34
20
20
20
20
20
20
" " - Vendor Name ASCII character
" " - Vendor Name ASCII character
" " - Vendor Name ASCII character
" " - Vendor Name ASCII character
" " - Vendor Name ASCII character
" " - Vendor Name ASCII character
66
67
68-83
84-91
92
93
00
00
Vendor Serial Number, ASCII (Note 8)
Vendor Date Code, ASCII (Note 9)
Note 5
Note 5
35
36
20
00
" " - Vendor Name ASCII character 94
95
Note 5
Checksum for bytes 64-94 (Note 7)
96 - 255 00
Notes:
1. FC-PI speed 100 MBytes/sec is a serial bit rate of 1.0625 GBit/sec.
2. Link distance with 50/125µm cable at 1.25Gbps is 550m.
3. Link distance with 62.5/125µm cable at 1.25Gbps is 275m.
4. The IEEE Organizationally Unique Identifier (OUI) assigned to Avago Technologies is 00-17-6A (3 bytes of hex).
5. See Table 11 for part number extensions and data-fields.
6. Laser wavelength is represented in 16 unsigned bits. The hex representation of 850nm is 0352.
7. Addresses 63 and 95 are checksums calculated per SFF-8472 and SFF-8074, and stored prior to product shipment.
8. Addresses 68-83 specify the module’s ASCII serial number and will vary by unit.
9. Addresses 84-91 specify the module’s ASCII date code and will vary according to manufactured date-code.
15
Table 11. Part Number Extensions
AFBR-5701ALZ
Address
48
49
50
51
92
93
94
Hex
31
41
4C
5A
00
00
00
ASCII
1
A
L
Z
AFBR-5701APZ
Address
48
49
50
51
92
93
94
Hex
31
41
50
5A
00
00
00
ASCII
1
A
P
Z
Address
48
49
50
51
92
93
94
AFBR-5701LZ
Hex
31
4C
5A
20
00
00
00
ASCII
L
1
Z
Address
48
49
50
51
92
93
94
AFBR-5701PZ
Hex
31
50
5A
20
00
00
00
ASCII
1
P
Z
Address
48
49
50
AFBR-5705ALZ
Hex
35
41
4C
ASCII
5
A
L
51
92
93
94
5A
68
F0
01
Z
AFBR-5705APZ
Address
48
49
50
Hex
35
41
50
ASCII
5
A
P
51
92
93
94
5A
68
F0
01
Z
Address
48
49
50
AFBR-5705LZ
Hex
35
4C
5A
ASCII
5
L
Z
51
92
93
94
20
68
F0
01
Address
48
49
50
AFBR-5705PZ
Hex
35
50
5A
ASCII
5
P
Z
51
92
93
94
20
68
F0
01
16
Table 12. EEPROM Serial ID Memory Contents - Address A2h (AFBR-5705Z family only)
Byte #
Decimal
Notes Byte #
Decimal
3
4
5
6
7
8
9
0
1
2
13
14
15
10
11
12
18
19
16
17
20
21
22
23
24
25
29
30
31
32
33
34
35
26
27
28
36
37
38
39
40-55
56-94
97
98
95
96
99
100
101
102
103
Temp H Alarm MSB 1
Temp H Alarm LSB 1
Temp L Alarm MSB 1
Temp L Alarm LSB 1
Temp H Warning MSB 1
Temp H Warning LSB 1
Temp L Warning MSB 1
Temp L Warning LSB 1
V
CC
H Alarm MSB 2
V
CC
H Alarm LSB 2
V
CC
L Alarm MSB 2
V
CC
L Alarm LSB 2
V
CC
H Warning MSB 2
V
CC
H Warning LSB 2
V
CC
L Warning MSB 2
V
CC
L Warning LSB 2
Tx Bias H Alarm MSB 3
Tx Bias H Alarm LSB 3
Tx Bias L Alarm MSB 3
Tx Bias L Alarm LSB 3
Tx Bias H Warning MSB 3
Tx Bias H Warning LSB 3
Tx Bias L Warning MSB 3
Tx Bias L Warning LSB 3
Tx Pwr H Alarm MSB 4
Tx Pwr H Alarm LSB 4
Notes:
1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256 °C.
2. Supply voltage (V
CC) is decoded as a 16 bit unsigned integer in increments of 100 µV.
3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 µA.
4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 µW.
5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 µW.
6. Bytes 55-94 are not intended from use with AFBR-5705Z, but have been set to default values per SFF-8472.
7. Bytes 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment.
8. Byte 127 accepts a write but performs no action (reserved legacy byte).
9. Bytes 128-247 are write enabled (customer writable).
Notes Byte #
Decimal
Tx Pwr L Alarm MSB 4
Tx Pwr L Alarm LSB 4
Tx Pwr H Warning MSB 4
Tx Pwr H Warning LSB 4
Tx Pwr L Warning MSB 4
Tx Pwr L Warning LSB 4
Rx Pwr H Alarm MSB 5
Rx Pwr H Alarm LSB 5
Rx Pwr L Alarm MSB 5
Rx Pwr L Alarm LSB 5
104
105
106
107
108
109
110
111
112
113
Rx Pwr H Warning MSB 5
Rx Pwr H Warning LSB 5
Rx Pwr L Warning MSB 5
Rx Pwr L Warning LSB 5
114
115
116
117
Reserved
External Calibration Constants 6
118
119
Checksum for Bytes 0-94 7
Real Time Temperature MSB
Real Time Temperature LSB 1
Real Time Vcc MSB 2
1
120-122
123
124
125
Real Time Vcc LSB 2
Real Time Tx Bias MSB 3
Real Time Tx Bias LSB 3
Real Time Tx Power MSB 4
Real Time Tx Power LSB 4
126
127
128-247
248-255
Notes
Real Time Rx P
AV
MSB 5
Real Time Rx P
AV
LSB 5
Reserved
Reserved
Reserved
Reserved
Status/Control - see Table 13
Reserved
Flag Bits - see Table 14
Flag Bit - see Table 14
Reserved
Reserved
Flag Bits - see Table 14
Flag Bits - see Table 14
Reserved
Reserved
Reserved
Reserved 8
Customer Writable 9
Vendor Specific
17
Table 13. EEPROM Serial ID Memory Contents - Address A2h, Byte 110 (AFBR-5705Z family only)
Bit #
5
4
3
7
6
2
1
0
Status/Control Name
Tx Disable State
Soft Tx Disable
Reserved
Rx Rate Select State
Reserved
Tx Fault State
Rx LOS State
Data Ready (Bar)
Description
Digital state of SFP Tx Disable Input Pin (1 = Tx_ Disable asserted)
Read/write bit for changing digital state of SFP Tx_Disable function 1
Digital state of SFP Rate Select Input Pin (1 = full bandwidth of 155 Mbit) 2
Digital state of the SFP Tx Fault Output Pin (1 = Tx Fault asserted)
Digital state of the SFP LOS Output Pin (1 = LOS asserted)
Indicates transceiver is powered and real time sense data is ready (0 = Ready)
Notes:
1. Bit 6 is logic OR’d with the SFP Tx_Disable input pin 3 ... either asserted will disable the SFP transmitter.
2. AFBR-5705Z does not respond to state changes on Rate Select Input Pin. It is internally hardwired to full bandwidth.
Table 14. EEPROM Serial ID Memory Contents - Address A2h, Bytes 112, 113, 116, 117 (AFBR-5705Z family only)
3
2
1
5
4
0
7
9
0-5
Byte Bit # Flag Bit Name
112
113
116
1
0
3
2
7
5
4
7
6
7
6
6
0-5
Temp High Alarm
Temp Low Alarm
V
CC
High Alarm
V
CC
Low Alarm
Tx Bias High Alarm
Tx Bias Low Alarm
Tx Power High Alarm
Tx Power Low Alarm
Rx Power High Alarm
Rx Power Low Alarm
Reserved
Temp High Warning
Temp Low Warning
117
V
CC
High Warning
V
CC
Low Warning
Tx Bias High Warning
Tx Bias Low Warning
Tx Power High Warning
Tx Power Low Warning
Rx Power High Warning
Rx Power Low Warning
Reserved
18
Description
Set when transceiver nternal temperature exceeds high alarm threshold.
Set when transceiver internal temperature exceeds alarm threshold.
Set when transceiver internal supply voltage exceeds high alarm threshold.
Set when transceiver internal supply voltage exceeds low alarm threshold.
Set when transceiver laser bias current exceeds high alarm threshold.
Set when transceiver laser bias current exceeds low alarm threshold.
Set when transmitted average optical power exceeds high alarm threshold.
Set when transmitted average optical power exceeds low alarm threshold.
Set when received P_Avg optical power exceeds high alarm threshold.
Set when received P_Avg optical power exceeds low alarm threshold.
Set when transceiver internal temperature exceeds high warning threshold.
Set when transceiver internal temperature exceeds low warning threshold.
Set when transceiver internal supply voltage exceeds high warning threshold.
Set when transceiver internal supply voltage exceeds low warning threshold.
Set when transceiver laser bias current exceeds high warning threshold.
Set when transceiver laser bias current exceeds low warning threshold.
Set when transmitted average optical power exceeds high warning threshold.
Set when transmitted average optical power exceeds low warning threshold.
Set when received P_Avg optical power exceeds high warning threshold.
Set when received P_Avg optical power exceeds low warning threshold.
DEVICE SHOWN WITH
DUST CAP AND BAIL
WIRE DELATCH
13.8±0.1
[0.541±0.004]
2.60
[0.10]
AVAGO AFBR-570xZ
850 nm LASER PROD
21CFR(J) CLASS 1
COUNTRY OF ORIGIN YYWW
TUV XXXXXX
UL
13.4±0.1
[0.528±0.004]
55.2±0.2
[2.17±0.01]
FRONT EDGE OF SFP
TRANSCEIVER CAGE
0.7 MAX. UNCOMPRESSED
[0.028]
8.5±0.1
[0.335±0.004]
TX
6.25±0.05
[0.246±0.002]
13.0±0.2
[0.512±0.008]
RX
AREA
FOR
PROCESS
PLUG
STANDARD DELATCH
6.6
[0.261]
13.50
[0.53]
14.8 MAX. UNCOMPRESSED
[0.583]
12.1±0.2
[0.48±0.01]
DIMENSIONS ARE IN MILLIMETERS (INCHES)
Figure 7. Module drawing
19
Y
11x 2.0
3
X
16.25
MIN. PITCH
PCB
EDGE
16.25
REF. 14.25
11.08
8.58
5.68
34.5
10x 1.05 ± 0.01
Æ 0.1 S X A S
B
1
26.8
3x 10
7.2
2.5
PIN 1
10
3x 10
5
7.1
2.5
20
11
Æ 0.85 ± 0.05
Æ 0.1 S X Y
A
1
3.68
2x 1.7
8.48
4.8
9.6
11.93
11x 2.0
SEE DET AIL 1
9x 0.95 ± 0.05
Æ 0.1 L X A S
2
41.3
42.3
3.2
5
0.9
20x 0.5 ± 0.03
0.06 S A S B S
9.6
10.93
0.8
TYP.
PIN 1
10
20
11
10.53
11.93
4
2x 1.55 ± 0.05
Æ 0.1 L A S B S
DETAIL 1
Figure 8. SFP host board mechanical layout
2 ± 0.05 TYP.
0.06 L A S B S
NOTES
1. PADS AND VIAS ARE CHASSIS GROUND
2. THROUGH HOLES, PLATING OPTIONAL.
3. HATCHED AREA DENOTES COMPONENT AND
TRACE KEEPOUT (EXCEPT CHASSIS GROUND).
4. AREA DENOTES COMPONENT KEEPOUT
(TRACES ALLOWED).
DIMENSIONS IN MILLIMETERS
20
PCB
15
(0.59)
MAX.
3.5 ± 0.3
(0.14 ± 0.01)
41.73 ± 0.5
(1.64 ± 0.02)
1.7 ± 0.9
(0.07 ± 0.04)
BEZEL
AREA
FOR
PROCESS
PLUG
CAGE ASSEMBLY
9.8
(0.39)
MAX.
11
(0.43)
REF.
1.5
(0.06)
REF.
BELOW PCB
15.25 ± 0.1
(0.60 ± 0.004)
10.4 ± 0.1
(0.41 ± 0.004)
10
(0.39)
REF
TO PCB
0.4 ± 0.1
(0.02 ± 0.004)
BELOW PCB
16.25 ± 0.1
(0.64 ± 0.004)
MIN. PITCH
MSA-SPECIFIED BEZEL
DIMENSIONS ARE IN MILLIMETERS (INCHES).
Figure 9. Assembly drawing.
21
Ordering Information
Please contact your local field sales engineer or one of Avago Technologies franchised distributors for ordering information. For technical information, please visit Avago Technologies’ web-page at www.avagotech.com or contact one of Avago Technologies’ regional Technical Response Centers. For information related to SFF Committee documentation visit www.sffcommittee.org.
AFBR-5705LZ DMI
AFBR-5705PZ DMI
AFBR-5705ALZ DMI
AFBR-5705APZ DMI
AFBR-5701LZ No DMI
AFBR-5701PZ No DMI
AFBR-5701ALZ No DMI
AFBR-5701APZ No DMI
Extended Temperature (-10°C to 85°C)
Extended Temperature (-10°C to 85°C)
Industrial Temperature (-40°C to 85°C)
Industrial Temperature (-40°C to 85°C)
Extended Temperature (-10°C to 85°C)
Extended Temperature (-10°C to 85°C)
Industrial Temperature (-40°C to 85°C)
Industrial Temperature (-40°C to 85°C)
Standard Delatch
Bail Delatch
Standard Delatch
Bail Delatch
Standard Delatch
Bail Delatch
Standard Delatch
Bail Delatch
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries.
Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved.
AV01-0093EN - May 7, 2006
22
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement