USER MANUAL

TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND INSTRUCTION MANUAL

ECO.50

Magnetic Drilling Machine

SERIAL NO._______________ DATE OF PURCHASE _____________

1 - Table of Contents

6

5

4

4

3

4

2

1 Table of Contents …………………………………………………………………………………………………… page 1

Safety …………………………………………………………………………………………………………………….. page 2

Before Use ……………………………………………………………………………………………………………… page 3

Items Included in Delivery ………………………………………………………………………………………. page 4

The Hole Cutter

Hole Cutter Selection ................................................................................................. page 5

Cooling/Lubrication ................................................................................................... page 6

Tool Assembly

Morse Taper Assembly ………………….........………………………………………………………………… page 6

Hole Cutter Assembly ………………….........………………………………………………………………… page 6

Drill Chuck Assembly ……………………………….........……………………………………………………. page 7

Installation of 13mm Chuck by using Adaptor IBK.14 ................................................ page 7

Installation of 13mm Chuck directly on the motor unit ............................................ page 7

The Magnetic Drilling Machine

The Magnetic Base .................................................................................................... page 7

The Control Panel ...................................................................................................... page 8

Drilling ........................................................................................................................ page 9

Maintenance ................................………………………………………………………………………….. page 10

Spareparts & Exploded View.........……………………………………………………………………....... page 11

Read these directions and safety instructions completely and attentively and carefully follow these recommendations.

All safety measures must be observed at all times when using magnetic drilling machines. Improper use and carelessness

increase the risk of accidents. This is for your own safety.

Should you have any doubts about the use of this machine,

2

please contact your supplier

2 - Safety

1. During any work on non-horizontal components, the machine must always be secured with the supplied safety chain.

2. The magnetic drilling machine may only be used on a flat and clean foundation.

3. If the machine or the lead show signs of damage, the magnetic drilling machine must be switched off immediately.

4. Wearing safety glasses, hearing protection and protective clothing is necessary.

5. Do not wear any loose clothing or jewellery that may get entangled in the moving parts of the magnetic drilling machine.

6. Use only accessories or parts that are recommended by Euroboor.

7. During drill operations, the hole cutter must be cooled and lubricated with good quality cutting or lubrication oil.

8. The motor must be switched off when tightening the machine with the safety chain.

9. When changing a hole cutter, the magnetic drilling machine must be disconnected from power supply.

10. Clean the area around the machine regularly. Keep the bottom of the magnet and keep it clean and dry.

11. Regularly inspect whether all screws, nuts and bolts are tight.

12. Remove the burr or slug from the hole cutter after each hole. Caution, the part may be hot!

13. Before using the machine make sure it is connected to the correct voltage and that all grips and parts are tightly attached.

14. When using the drill on non-horizontal surfaces, you must use a drilling compound or cutting paste.

15. Do not use oil because the oil can drip into the motor unit.

When using this machine, you MUST wear ear and eye protection.

Euroboor has included these articles as standard accessories for your own

safety. Do NOT touch the drill when it is running. Always follow the

recommendations for personal protection when using this tool.

3

Before use

Euroboor magnet drilling machines are specially designed for drilling holes is steel, possibly expanded by the possibility of tapping/reaming/countersinking (depending on model). Euroboor magnetic drilling machines may not be adapted and/or used for applications other than those they were designed for, including driving other machines.

Make sure that you can oversee the entire work areas from where you are operating this machine. Use barriers to keep others away. Do not use the machine in places subject to hazard of explosion- electrical tools produce sparks which may ignite flammable materials or gasses. To prevent electrical shocks, do not use the machine in moist or wet conditions or environments. Always operate this tool using both hands.

Make sure the work piece is always clamped down safety.

This magnetic drilling machine is equipped with a lead and plug approved for the country or region it is to be used in. The yellow-green wire in the lead is the earth wire. Never connect this to a pole under voltage.

All Euroboor magnetic drilling machines are manufactured to use with AC current and not suitable to work on DC current. Make sure the magnetic drilling machine is connected to a stable power supply. Euroboor do not recommend the use of a generator or other mobile power supply for power supply. Euroboor does not recommend the use of extension cables. If there is no other way, use good quality cables and keep extension cables as short as possible. Be aware that long power leads can cause less current.

3 - Items Included in Delivery

Magnetic Drilling Machine

Carrying Case

YES Pilot Pin

YES Morse Taper

Drill Chuck 13mm NO Morse Taper Ejector Pin

Tap Collets M10-M12-M14-M16 NO Manual

Allen Key 2.5

Allen Key 3

Allen Key 4

Allen Key 5

Wrench 8

YES

NO

YES

YES

YES

Safety Chain

Drilling Oil

Safety Ear Protection

Safety Glasses

Safety Gloves

NO

YES

YES

YES

YES

YES

YES

YES

YES

4

4 - The Hole Cutter

Hole Cutter selection

There are many different types of steel. It is not possible to drill all these types of steel with 1 type of cutter. Euroboor recommended the following :

Euroboor+ HSS Series For drilling holes in general 37/52 steel and aluminium

HCS 12 mm - 130 mm Hole cutters with cutting depth 30 mm increasing by 1 mm

HCL 12 mm - 130 mm Hole cutters with cutting depth 55 mm increasing by 1 mm

HCY 20 mm - 50 mm Hole cutters with cutting depth 75 mm increasing by 1 mm

HCX 20 mm - 50 mm Hole cutters with cutting depth 100 mm increasing by 1 mm

Also available in inch sizes:

HCS 7/16” - 5” Hole cutters with cutting depth 30 mm increasing by 1/16”

HCL 7/16” - 5” Hole cutters with cutting depth 55 mm increasing by 1/16”

HCY 3/4” - 2 1/16” Hole cutters with cutting depth 75 mm increasing by 1/16”

HCX 3/4” - 2 1/16” Hole cutters with cutting depth 100 mm increasing by 1/16”

Euroboor Cobalt Series For processing steel, stainless steel and other high-quality steel alloy types

IBS 12 mm - 130 mm Hole cutters with cutting depth 30 mm increasing by 1 mm

IBL 13 mm - 130 mm Hole cutters with cutting depth 55 mm increasing by 1 mm

Euroboor TCT Series Tungsten Carbide Tipped. Cutters with hard metal teeth

HMS 14 mm - 50 mm Hole cutters with cutting depth 35 mm increasing by 1 mm

HML 14 mm - 130 mm Hole cutters with cutting depth 50 mm increasing by 1 mm

Euroboor TRC Series With hard metal teeth, For drilling holes in rails

TRCS.190 19 mm Hole cutter with cutting depth 35 mm

TRCS.300 30 mm Hole cutter with cutting depth 35 mm

TRCS.330 33 mm Hole cutter with cutting depth 35 mm

NOTE : Hole cutters 12mm - 60mm have a 19,05 mm Weldon shank

Hole cutters 61mm - 130mm have a 31,75 mm Weldon shank

5

Cooling/Lubrication

1 Holes for cooling and lubrication oil

2 Fixing screws of Morse Conus

Euroboor recommends the use of cooling and lubrication agents. Not only do these assist in drilling but they will also lengthen the lifespan of your tools. One of the advantages of the use of hole cutters is that cooling and lubrication agent scan be supplied from the inside, so that the agents end up in the right place.

All magnetic drilling machines from Euroboor can be equipped with a automatic cooling system which provides a guaranteed supply of the cooling and lubrication agents from the inside. If your machine is not be equipped with an automatic coolant system it will still be possible to cool from the inside.

Use the holes in the morse conus (number 1 in picture) for this purpose by squirting the cooling and lubrication agent through them and fill the morse conus.

NOTE : For vertical or upside-down processing, Euroboor recommends the use of a drilling

compound or paste like IBP50/2.

4 - Tool Assembly

Morse Taper Assembly

Mount the Morse Taper into your machine by push it firm into the shaft ectending from the motorunit.

Beware that the tip on top of the Morse Conus is in line with the shaft. To take the Morse Conus out use the Ejector Pin to force it out.

Hole Cutter Assembly

1 : Pilot Pin

2 : Center hole in shank of Hole Cutter

3 : Shank of Hole Cutter

4 : Groove or flatted surface for oil pass

5 : Flat surface for fixing Hole Cutter

Clean the inner wall and the shaft of the Hole Cutter to ensure proper oil supply.

First insert the Pilot Pin into the center hole of the Shank. After that you can slide the Hole Cutter assembly into the spindle or morse conus of your Magnetic Drilling

Machine. After sliding the Hole Cutter Assembly into the morse conus, make sure the two flat surfaces (number 5 in picture) are located exactly in front of the two

6

fixing screws of your spindle (see number 2 in picture of cooling/lubrication. Tighten them both subsequently with the included 5mm Allen Key.

Drill Chuck Assembly

The option of making our machines suitable for the use of standard spiral drills and other tools by using a cylindrical shaft is an important characteristic of Euroboor magnetic drilling machines. Please see the technical data for maximum capacity.

Installation of 13mm Chuck by using adapter IBK.14

The IBK.14 is a adaptor from 1/2"x20 UNF to 3/4" Weldon.

Attach a Drill Chuck (like Euroboor IBK.13) with internal 1/2"x20 UNF on the IBK.14 adaptor.

To attach the assembly into your Spindle, follow the instructions (with exception of the Pilot Pin) for installation of a Hole Cutter. Adaptor IBK.14 can be used on most machines in our program.

Installation of 13mm Chuck directly on the motor unit

For the ECO.50 and ECO.50T magnetic drilling machines it is possible to install a drill Chuck directly to the shaft extending from the motor unit. Attach to the drill chuck with article number IBK.13-B16 a adaptor with article number B16-MC2. This way the drill chuck can be mounted as a Morse Conus in your machine.

4 - The Magnetic Drilling Machine

The Magnetic base

Material of minimum 10mm thickness is required for the magnet to work the best.

The attachment force generated by the magnet depends on various factors.

- Thickness of the material the magnet is placed on

- Paint or coating of the material the magnet is placed on.

- Metal chips, oil or other dirt under the magnet.

If the LED indicator lights up GREEN, the magnet is generating sufficient attachment force. If the LED indicator lights up RED, the magnet may not generating sufficient attachment force.

We would like to point out that this is only an indication and not a certainly that the magnet will not release from the material. Euroboor accepts no liability ensuring from the magnet indicator not

functioning or functioning poorly.

Make sure that the magnet attaches tightly to the work piece before turning on the motor unit of the magnetic drilling machine. Euroboor magnets have 2 coils; make sure that both coils are in contact with the material. Do not connect any other machines to the electrical outlet the magnetic drilling machine is plugged into, as it may result in the loss of magnetic force. Always use the safety chain included. Drilling above your head is extremely dangerous and is not recommended. For the use of magnetic drilling

7

machines on pipes, not-flat or non-magnetic materials, we refer to our brochure or our website www.euroboor.com where several vacuum tightening systems and pipe clamping systems are mentioned.

The Control Panel

The control panel on your magnetic drilling machine is designed for maximum operating facility and safety.

1 - The Magnet Switch:

This switch is used to switch the main power and also the magnet On and Off. This switch is included on every

Euroboor magnetic drilling machine

2 - The On/Off Switch:

This switch is used to switch the motor unit On and Off and is included on every Euroboor Magnetic Drilling

Machine

3 - The Fuse holder with Fuse:

This Fuse holder is included on every Euroboor Magnetic

Drilling Machine and holds the fuse type : 5x20, F2A.

4 - The Magnet LED Indicator:

This LED indicator shows the generated magnetic force.

8

Drilling

Now that you have read the explanatory information and safety recommendations above, you are ready to actually start drilling. Follow these 10 steps for best drilling result :

1 Use the tip of the pilot pin to determine the center of the hole to be drilled.

2 Turn the magnet on and verify that the drill is in the right position and that the machine is

pushed tight against the work piece.`

3 If your machine is equipped with a auto coolant system, put open the valve to release the oil.

If your machine does not have a auto coolant system, fill the holes of the spindle with oil.

4 Turn the motor on at the highest setting and allow it to run at full speed.

5 Turn the arms to start drilling. Apply only a slight pressure when the hole cutter touch the

metal. Do not push the hole cutter with force into the metal.

6 Apply a regular pressure while drilling. The drilling performance does not improve by putting

more pressure on the tool. Too much pressure will overload the motor and your hole cutter

will be worn sooner. Let the cutter do the job and give it time to cut the metal !!!

7 Adjust the oil supply when necessary, if your drill does not have a auto coolant system, stop

drilling regularly, refill the holes of the spindle and continue drilling.

8 Apply less pressure when the drill cuts through the material.

9 Turn the arms to put the motor in highest position and turn off the motor unit.

10 Remove the burr, metal chips and clean the cutter and surface without getting injuries.

Caution : The metal piece drilled out can be sharp and very hot!!

The ECO.50 have a 2speed gearbox. Easy said can the upper (high) gear be used for hole cutters till 20mm and twist drilles. The lower gear is used for hole cutters above 20mm. Of course this is a general indication, at specific constructions and/or materials or used cutters can a lower or higher rpm give better results.

To select other gear, turn off motorunit and main power. Push the black switch on the side of the gearbox and slide to other position. A slight turn of the output shaft by hand while sliding the black switch to the other position can be necessary to line up the gears inside. Proof that the gear is locked if the black switch comes back to front.

!!! IMPORTANT !!!

When using your magnetic drilling machine non-horizontal or upside-down be aware that no oil, drilling compound or metal chips can fall into the motor unit.

Euroboor accepts no responsibility for damage done to your machine by such action under coverage of the warranty.

9

5 - Maintenance

Just as every magnetic drilling machine with moving parts, your Euroboor magnetic drilling machine also needs regular maintenance service. A few recommendations follow :

- Clean all dirt, dust, metal chips and burrs of your magnetic drilling machine

- Regularly check the carbon brushes for wear

- Replace any defective parts immediately. This prevents properly function parts from being damaged.

- Adjust your guide regularly and make sure it is clean and greased. This prevents any movement from being created and the spindle, triangular guide (steady) and guide parts from excessive wear or damage. The guide can be adjusted by loosening the setting nut (#7 on spare part drawing) with included wrench 8, tightening the setting screws (#5 on spare part drawing) with included Allen key

2.5 and tightening the setting nut (#7) again with included wrench 8. The adjustment is done well when the motor unit can be turned to every possible position without falling down by its own weight.

- Check the grease in the gearbox regularly and replace it if necessary. We recommend you to store your machine on its side regularly so that the gear box grease can run back to where the gears are.

This is very important when you have used your machine non-horizontal or upside down.

Repair, modification and inspection of Euroboor Magnetic drilling machines must be done by a

Euroboor authorized dealer. The parts list will be helpful if presented with the machine to the

Euroboor dealer for service when requesting repair or other maintenance.

Euroboor machines are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts (ie part numbers and/or design) may be changed without prior notice. Also, due to Euroboor's continuing program of research and development, the specifications of machines are subject to change without prior notice.

10

34

35

36

6 - Spare parts & Exploded view of ECO.50

020.0101

PP.50EU

020.0206

020.0006

020.0016

020.0017

020.0011

020.0001

020.0002

020.0037

050.0101

050.0102

050.0586

020.0056

020.0106

020.0111

020.0096

020.0091

050.0611

020.0201

050.0011

032.0016

020.0156

050.0141

020.0146

040.0041

020.0086

020.0084/4

020.0061

020.0077

020.0081

020.0066

020.0046

020.0041

020.0031

020.0036

020.0182

PP.RSEU

22

23

24

25

18

19

20

21

14

15

16

17

10

11

12

13

30

31

32

33

26

27

28

29

1

6

7

8

9

2

3

4

5

Frame

Screw SSM6x16

Washer M6

Setting Nut

Setting Screw

Magnet Hi/Lo

Sensor

Slide

Rack

Screw SSM6x20

Motorholder

Screw SSM6x25

Top fixing plate 110mm

Brass rail set (stick)

Pressing strip 4 holes

Capstan hub assembly

End plate

End screw

Arm for Capstan

Motorcable

Coupling nut for motorcable

Coupling nut for maincable

Main Cable

Screw+washer+nut

Rear plate

Panel screw M4x8

Front plate

Sensor LED+cable

On/Off switch

Fuse holder

Fuse F2A

Magnet switch

Control Unit 220v

Control Unit 110v

Cable clamp

Motorunit 220v

Motorunit 110v

Cable housing

37

55

56

57

58

51

52

53

54

050.0587

032.0156

050.0182

050.0161

032.0221

032.0171

050.0251

050.0231

050.0246

63

64

65

66

59

60

61

62

67

68

69

70

71

72

80

81

82

83

84

73

74

75

76

050.0142

050.0176

050.0426

050.0166

77 050.0236

77.1 050.0207

78

79

050.0206

050.0431

050.0301

032.0211

050.0291

040.0286

050.0211

050.0191

050.0371

050.0147

050.0112

032.0106

050.0116

050.0466

050.0221

050.0177

050.0171

050.0261

050.0181

050.0186

050.0276

050.0277

050.0111

Screw PKVZ4,8x35

Screw 3,9x60

Adaptor ring 22x0,2

Needle bearing

Bearing 8x22x7

Bearing 12x28x8

First gear

Axle

Gear shaft

Spindle drive shaft

Carbon brush holder

Carbon brush set

Screw 4,8x45

Screw 4,8x50

Adaptor ring rubber 22x2,5

Bearing 20x37x9

Bearing 17x40x12

Spindle gear

Gear 34/40

Baffle

Armature 220v

Armature 110v

Field 220v

Field 110v

End cover

Housing

Circlip 471/10

Circlip 471/15

Circlip 472/28

Inner gear plate

Gasket

Gear casing

Key for spindle

Key

Casing pin

Clutch shaft

Gear switch

Plate for gear casing

11

12

Important notice :

Because of minor changes to our machines it is recommended to provide the framenumber of your machine when ordering spareparts. This number can be found on front of machine at magnetic base and frame. When you have any doubt when ordering spareparts, please contact your supplier before ordering.

13