HE1LBIR232-E-ARC-100M Instructions

HE1LBIR232-E-ARC-100M

HDMI (HDBaseT) Cat5/6 Extender with Ethernet/ARC/IR/RS232

Extend high-resolution HDMI and IR up to 100M with this HDMI over single cat5e/cat6 extender. This extender uses HDBaseT technology to extend uncompressed high-definition video/audio with a data transfer rate of 10.2Gbps. This product also meets all HDMI v1.4 standards including full 3D support, HDMI Ethernet Channel, audio return channel and 4Kx2K Resolution. Additional Ethernet ports on both the Sender and Receiver are connected to standard network devices such as 100Base-T routers, hubs and computers. HDMI and Ethernet signal can be transmitted simultaneously without affecting each other. This product offers the ideal solution for extending high-definition video and audio over long distances.

Features:

>

Extends HDMI, Ethernet, ARC, RS232 and IR signal over one CAT5e/6 cable

>

Uncompressed high definition video up to 1080p@60Hz@48bits

>

HDMI 3D, 4k x 2k support, HDCP & DVI Compliant

>

Max. Data Rate- 10.2Gbps

>

Audio supports up to LPCM 7.1 @ 192KHz, Dolby TrueHD, DTS-HD MA

>

Transmission range up to 100 meters at 1080p resolution

>

Support one port 10/100Mbps network, allow to connect the network TV or devices

>

ARC or optical digital audio mode auto selection, send TV digital audio back to the amplifier

>

Bi-directional IR, IR carrier support 30-60khz

>

Bi-Directional RS232 interface – commands and data can flow in both directions via RS232, allowing status requests and control of the

destination unit.

Panel View:

(Transmitter Front) (Transmitter Back)

(Receiver Front) (Receiver Back)

Installation View:

8805 Jones Road Suite C104, Houston, TX 77065 * 1-888-861-7351 * www.zuummedia.com ZM61714

8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014

Operation and Connections:

Low-power Mode: If there is no HDMI video input the extenders will enter a low-power mode to save power. Under low power mode, it will still provide Ethernet, RS-232 (Max 9600bps), IR, CEC and digital optical audio transmission.

Digital Audio Return (ARC): This HDMI extender supports the audio from the TV to be sent from HDMI ARC or Digital optical audio mode from the HDMI receiver back to the HDMI transmitter.

On the HDMI receiver when ARC and optical digital inputs signals simultaneously, it will use optical digital as the priority transmission.

On the HDMI transmitter when it receives digital audio signal, it will output simultaneously from ARC and optical digital.

Caution: The wiring must be away from any equipment with electromagnetic signal, i.e.: mobile phone, microwave, radio equipment, fluorescent lamp, and high voltage power lines.

This HDMI extenders HDBaseT port is not for an Ethernet signal, do not connect to Network to avoid damage. Connect your network connection to RJ45 connection marked Ethernet.

Transmission Range: If connection is through a wall jack, (not recommended) this could limit the full transmission distance between the Transmitter and Receiver Extenders. We only recommended using a straight CAT5/6 cable with RJ45 connections on each end.

Shielded Cable: On most installations it is recommended to use Shielded CAT5/6 cable with properly connected shielded RJ45 connectors. This will prevent video and audio loss due to EMI and other interference from switched lighting and ceiling fans.

Connecting/LED Light Status TX/RX:

- Step 1: First plug power into both the HE1LBIR232 transmitter and receiver. You should see Power light (On Solid Green) for both units.

- Step 2: Connect your Cat5/6 cable to both transmitter and receiver unit. You should then see the Link light (L) (Blink

Green).

- Step 3: Next go ahead and plug the HDMI cable from your source into the transmitter and the HDMI cable from TV into the receiver unit. Turn both source and TV on. At this time once they communicate which should be within a few seconds the Link light (H) will go to a solid red light and you should see a picture at this time.

IR Control Connections:

- Example 1: When using IR remote control at TV side, plug IR receiver into HDMI Receiver Extender and move IR switch to RX meaning it will receive incoming IR commands from remote. On the source side plug IR blaster into

HDMI Transmitter Extender and move IR switch to TX meaning it will blast out IR commands to source equipment.

- Example 2: In an example where you use an RF remote or other control system and it communicates back to an RF receiver and then outputs IR commands to the source equipment and back to TV you will want to set the IR

If connecting to other manufacturer emitters or control systems use our IR adapter cable Model:HE1LIR35M35F-.5. blaster at the TV location to control the TV and plug into HDMI extender receiver and set the switch to TX outputting IR code to TV. On the HDMI extender transmitter you will set the switch to RX to receive IR code.

This way when your RF or other control systems output its IR code it can emit to the IR receiver included with the HDMI extender or use our adapter cable between the HDMI receiver extender and your control system and control TV or other equipment in that area.

IR Lights:

On the HDMI TX and RX the IR lights will perform as follows: (R) Will blink BLUE when receiving IR commands.

(T) will blink RED when sending IR commands.

Note: Do not place the IR blaster near or in an area that allows the signal to affect the IR receiver. This can cause interference and unreliable performance.

8805 Jones Road Suite C104, Houston, TX 77065 * 1-888-861-7351 * www.zuummedia.com ZM61714

8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014

RJ45 Defined:

Package Contents:

- HE1LBIR232-E-ARC-100M Transmitter x 1

- HE1LBIR232-E-ARC-100M Receiver x 1

- Power adapter x 2

- Mounting screw pack x 2

- IR Blaster cable x 1

- IR Receiver cable x 1

- Product Instructions

General Specifications:

Model

HDMI Video Support

HDMI Distance

HDMI Connector

HDMI Audio Support

HDBaseT Connector

Ethernet Connector

Ethernet Data Rate

Ethernet Distance

RS-232 Connector

RS-232 Baud Rate

IR Connector

IR Carrier

Digital Audio Connector

Power Supply

Power Consumption

Dimensions

Weight lbs

Humidity

Storage Temperature

Operating Temperature

HE1LBIR232-E-ARC-100M-TX HE1LBIR232-E-ARC-100M-RX

Up to 1080p@60Hz@48bits, 3D, 4Kx2K

Up to 328’ (100 meters)

Type A

Up to LPCM 7.1 192KHz, Dolby TrueHD, DTS-HD MA

RJ45 x 1

RJ45 x 1 (with 2 LED)

10 / 100Mbps

Up to 328’ (100 meters)

DB9 Female DB9 Male

Optical (Toslink)

Up to 115200 bps / Full Duplex

3.5mm Phone Jack x 2

30-60KHz (2 Way)

Optical (Toslink)

Regulated 5V 2Amp x 2

800mA (Max) 1200mA (Max)

3.46” x 4.72” x 1.18”

.57 .62

Up to 95%

-4 to 185°F

32 to 131°F

8805 Jones Road Suite C104, Houston, TX 77065 * 1-888-861-7351 * www.zuummedia.com ZM61714

8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014