Axiohm TPOS printer series thermal printer Set-up Guide
Axiohm TPOS PRINTER SERIES is a robust thermal printer with a guillotine cutter that makes clear and legible receipts. It comes with easy paper loading thanks to its clamshell design and can be either horizontally or wall mounted. It has a USB connector and can also be connected through a RS232 interface.
Advertentie
Advertentie
THERMAL PRINTING SOLUTIONS
TPOS PRINTER SERIES
SET-UP GUIDE
Reference 3107243 Issue A
April 2003
AXIOHM
1, rue d'Arcueil, BP 820
92542 MONTROUGE CEDEX
FRANCE
Tel : (33) 1 58 07 17 17, Fax : (33) 1 58 07 17 18 www.axiohm.biz
CONTENTS
1 YOUR PRINTER
.......................................................................... 2
1.1
Package....................................................................................................2
1.2
General description ................................................................................2
1.3
Printer location........................................................................................3
2 PLUGGING & CONNECTING YOUR PRINTER
........................ 4
2.1
Connecting the power supply................................................................4
2.2
Connecting the printer............................................................................4
2.3
Connector pin out / features ..................................................................5
2.3.1
Power connector.......................................................................5
2.3.2
2.3.3
2.3.4
Communications interface connectors .....................................5
Drawer kick-out connector (optional)........................................5
USB connector..........................................................................6
2.4
General safety specification ..................................................................6
3 LOADING PAPER........................................................................ 7
4 CUTTING FEATURES ................................................................. 8
5 STANDARD DEFAULT SETTINGS............................................. 8
6 DUTY CYCLE............................................................................... 8
7 POWER SUPPLY KITS
................................................................ 8
8 TROUBLESHOOTING
................................................................ 9
8.1
Light indicator .........................................................................................9
8.2
Problems & Solutions.............................................................................9
8.2.1
Printer Problems .......................................................................9
8.2.2
8.2.3
8.2.4
Printer LED Diagnostic ...........................................................10
Printing Problems....................................................................11
Auto Cutting Problems............................................................12
9 CLEANING YOUR PRINTER
.................................................... 12
TPOS PRINTER SERIES Set-up Guide
Page 1 / 12
Reference: FDE-3107243 Issue A
1 YOUR PRINTER
1.1
Package
The packing box contains:
Printer
Power supply (optional)
Power cable to be set between power supply and power network (optional)
Set Up Guide
1.2
General description
The TPOS is a complete printer designed with the clamshell easy paper loading system.
Opening cover
Finger recesses to open cover
Tear bar
Light indicator
Access to manual operation of blade
(optional)
Paper feed button
Reset button
Note
1
: when resetting the printer, every running operation is stopped and all information sent before resetting are lost.
Note
2
: to print a self-test ticket, activate both On and paper feed buttons according to the following instructions:
Switch the power Off.
Activate the paper feed button while turning the power On.
Release the On/Off button keeping the paper feed button pushed.
Release the paper feed button as soon as the printer starts to print the self-test ticket.
TPOS PRINTER SERIES Set-up Guide
Page 2 / 12
Reference: FDE-3107243 Issue A
1.3
Printer location
This printer can be used either horizontally or wall mounted (fixing holes on printer bottom for 3 mm screws, not included).
The external dimensions (W
×
L
×
H) are: 121
×
185
×
125 mm (with cover closed).
The printer should be set on a stable holder in a place where the following conditions are achieved:
temperature from 0 to 50°C for operating (-40 to +70 for storage).
no risk of water exposure.
no mechanical vibration or stress.
Wall mounting diagram:
TPOS PRINTER SERIES Set-up Guide
Page 3 / 12
Reference: FDE-3107243 Issue A
2 PLUGGING & CONNECTING YOUR PRINTER
2.1
Connecting the power supply
To the power network
To the printer
The cable to connect the printer to the power network is included in the package.
2.2
Connecting the printer
Connections have to be set at the rear of printer: open the rear-door and set the power supply and interface cables as shown on the following drawing.
"Cash drawer kick out" label
USB Connector
Power Supply cable connector
RS232
Connector
USB LED
Cash drawer
Note
: All connectors should be SELV types in order to safety standards
(Safety extra low voltage).
TPOS PRINTER SERIES Set-up Guide
Page 4 / 12
Reference: FDE-3107243 Issue A
2.3
Connector pin out / features
To reduce the electromagnetic emissions and susceptibility, all cables should be shielded. If you are not using cables supplied by Axiohm for this purpose, make sure that your cables match the printer and are rated at the appropriate voltage and current capacities.
*Use of an inappropriate cable may seriously damage your printer!
2.3.1
Power connector
The connector is a shielded 3-pin female mini-Din plug.
Function Pin Numbers Function
+ 24V
2
Shell - Shield
3 Not Used
1 GND
2.3.2
Communications interface connectors
RS232 interface uses 9-pin D-type male connectors.
RS232 Connector
Cable for DTR/DSR protocol
CONNECTOR VIEW
1 2 3 4 5
6 7 8 9 male DB9 connector
N/C
RXD
TXD
DTR
GND
DSR
RTS
CTS
N/C
4:
5:
6:
7:
1:
2:
3:
8:
9: male DB9 connector
:5
:6
:7
:8
:9
:1
:2
:3
:4
N/C
RXD
TXD
DTR
GND
DSR
RTS
CTS
N/C
Note
: RTS/CTS should be tied together if using DOS print commands on a PC station.
2.3.3
Drawer kick-out connector (optional)
The following illustration shows the pinouts for the cash drawer connector on the printer.
Pin 1 Pin 6
Pin Number
1
2
3
4
5
6
Cash Drawer Connector
Switch (-ve)
Drawer 2 Solenoid
+24 Volts (to Solenoid +ve)
Status Switch +
Drawer 1 Solenoid (common with drawer2)
Frame Ground
The connector used to open a cash drawer and monitor, whether the drawer is opened or closed, is a 6-pin modular RJ11 connector.
TPOS PRINTER SERIES Set-up Guide
Page 5 / 12
Reference: FDE-3107243 Issue A
2.3.4
USB connector
The connector is located at the rear of the printer, and is of B-type. The maximum recommended cable length is 3 meters. Refer to USB specification rev 1.1, chapter 6, for more information.
USB PARAMETERS
Axiohm’s implementation of USB complies with “Universal Serial Bus Specification” revision 1.1.
2.3.4.1
Capabilities:
TPOS is only a device, and doesn’t provide hub capabilities. Full speed communications (12Mbits/sec) are supported.
2.3.4.2
Connector:
The connector is located at the rear of the printer, and is of B-type Refer to USB specification rev 1.1
chapter 6 for more information.
2.3.4.3
Interface:
The data is exchanged between host and printer via four endpoints:
1) Endpoint 0x00: CONTROL
Default endpoint
2) Endpoint 0x02: BULK OUT
For transmission of all printable data and commands from host to printer
3) Endpoint 0x82: BULK IN
For return of all synchronous data, status or other types of information except unsolicited status mode messages, from printer to host
4) Endpoint 0x01: INTERRUPT OUT
For transmission of real time commands from host to printer.
2.3.4.4
Other information:
Vendor Id
Axiohm USB Vendor Id = 0x05D9
Product Id
TPOS Product Id = 0xA000
2.4
General safety specification
All communication connectors should be SELV connectors in order to meet safety standards.
Use of an inappropriate cable or power supply may seriously damage your printer and affect safety standards of the printer. The power supply main connector should be accessed to enable power disconnection.
The power supply cable is a disconnect device.
Power supply input requirements: 110/240 VAC, 50/60 Hz.
Operating temperature: 0 to 50°C.
TPOS PRINTER SERIES Set-up Guide
Page 6 / 12
Reference: FDE-3107243 Issue A
The Clamshell design allows easy paper loading.
To load paper:
Open the cover using finger recesses.
Set the paper roll as indicated on the inside of the cover (see drawing).
Close the cover leaving a small length of paper out.
Cut the small length left with the tear bar.
Your paper roll is set.
Notes
:
The paper used should be recommended by AXIOHM.
The paper width must be 58
0/-0.3 mm.
The maximum paper roll diameter is 90 mm.
Warning
: If the paper width should be less than 57.7 mm, it is recommended to check that the printing is centered according to the paper.
The paper must not be attached to the paper roll spindle.
Roll setting indications
TPOS PRINTER SERIES Set-up Guide
Page 7 / 12
Reference: FDE-3107243 Issue A
The printer is equipped with a high performance guillotine cutter that can provide total and partial cuts by software command.
The partial cut leaves a 2 mm center tab.
5 STANDARD DEFAULT SETTINGS
Print density:
Pre heating:
Baud rate:
Parity:
Flow control:
Reception error:
100%
Off
115200
None
Dtr/Dsr
Ignore
25°C
50°C
Duty cycle is 30%
Duty cycle is 20%
7 POWER SUPPLY KITS
Reference Designation
A3107446 POWER SUPPLY KIT TPOS EU (12 items/kit)
A3107447 POWER SUPPLY KIT TPOS US (12 items/kit)
A3107448 POWER SUPPLY KIT TPOS GB (12 items/kit)
A3107589 POWER SUPPLY KIT TPOS AUST (12 items/kit)
TPOS PRINTER SERIES Set-up Guide
Page 8 / 12
Reference: FDE-3107243 Issue A
8 TROUBLESHOOTING
Axiohm printers are simple and generally trouble-free, but from time to time minor problems may occur.
Follow these procedures to determine the cause and resolution of any problems the printer may be having.
If the procedures in this section do not correct the problem, contact a service representative.
8.1
Light indicator
When light is on continuously, the printer is ready to operate.
When light is flashing, an error occurs.
8.2
Problems & Solutions
8.2.1
Printer Problems
Problem
Printer does not function when turned on.
Printer LED is off.
Printer LED is continuously on but printer does not operate.
Printer LED is flashing.
What to Do
Check that printer cables are properly connected on both ends.
When using the USB interface, check if the USB LED indicates data transmission. Check if the On/Off button is in On position.
Check that the host or power supply is getting power.
Check the power-supply and cable connections.
Check if the interface cable is properly connected.
Auto-cutter: Check that the mobile blade does not interfere with the cover blade.
Remove the Paper jam button. Using a screwdriver; turn the gear until the blade disappears.
Then open the cover and check that there is no paper jam.
Important
: Do not press on the switch when the cover is opened.
Then close the cover.
If the LED is still flashing, see LED diagnostic.
Manual cutter: Check that the cover is properly closed; if not close it.
Open the cover and make sure there is paper left in the printer; if not, remove the paper roll core, place a new paper roll as indicated in the chapter "Loading paper". See LED diagnostic.
Open the cover and make sure there is no paper jam. In case of paper jam, unwind the paper until no more wrinkle appear; close the cover with the wrinkled part out and cut it with the tear bar.
If the LED is still flashing, see LED diagnostic.
TPOS PRINTER SERIES Set-up Guide
Page 9 / 12
Reference: FDE-3107243 Issue A
8.2.2
Printer LED Diagnostic
Problem
LED, slow continuous flashing
(1 flash / sec or more).
Possible Causes
Out of paper.
Cover is off.
Knife is unable to home.
Print head is too hot.
Voltages are out of range.
What to Do
Put in a new paper roll.
Put the cover on.
Contact your authorized service representative.
Turn the printer off (
unplug
).
Contact your authorized service representative.
Flashing LED in various combinations.
Fast continuous flashing of LED:
Main Program CRC Test
Failure.
Auto cutter: The cover is opened and the cutter is not in its normal position.
Manual cutter: (no mobile blade)
You are in auto cutter mode.
These indicate serious problems.
Contact your authorized service representative.
Turn the gear using a screwdriver until the
LED flashes slowly. Check that the mobile blade is not interfering with the cover. Then close the cover.
Open the cover and refer to the chapter "Set knife option" to disable the knife.
If the problem continues, please contact your authorized service representative.
TPOS PRINTER SERIES Set-up Guide
Page 10 / 12
Reference: FDE-3107243 Issue A
8.2.3
Printing Problems
Problem
Print quality is deteriorating.
Colored stripe on the receipt.
Receipt does not come out all the way.
Printer starts to print, but stops while the receipt is being printed.
Possible Causes
Print head may be getting dirty.
Paper is low.
Paper is jammed.
Paper is jammed.
What to Do
See next chapter ”Cleaning your printer”.
Change the paper.
Auto-cutter: Check that the mobile blade does not interfere with the cover blade.
Remove the Paper jam button. Using a screwdriver; turn the gear until the blade disappears.
Then open the cover and check that there is no paper jam.
Important
: Do not press on the switch when the cover is opened.
Then close the cover.
If the LED is still flashing, see LED diagnostic.
Manual cutter: Check that the cover is properly closed; if not close it.
Open the cover and make sure there is paper left in the printer; if not, remove the paper roll core, place a new paper roll as indicated in the chapter
"Loading paper". See LED diagnostic.
Open the cover and make sure there is no paper jam. In case of paper jam, unwind the paper until no more wrinkle appear; close the cover with the wrinkled part out and cut it with the tear bar.
If the LED is still flashing, see LED diagnostic.
Check that the paper is loaded properly.
Print is light or spotty.
Paper roll is loaded incorrectly.
Thermal print head is dirty.
Variations in paper.
Vertical column of print is missing.
One side of receipt is missing.
This indicates a serious problem with the printer electronics.
This indicates a serious problem with the printer electronics.
Use recommended thermal receipt paper. See next chapter "Cleaning your printer".
Increase print density in “Set Hardware Options” of printer Configuration Menu as needed.
Contact your authorized service representative.
Contact your authorized service representative.
TPOS PRINTER SERIES Set-up Guide
Page 11 / 12
Reference: FDE-3107243 Issue A
8.2.4
Auto Cutting Problems
Problem
The ticket is out of the printer, but the cutter does not cut.
What to Do
Cut command is not used correctly.
Faulty cutter.
Total cuts instead of partial cuts.
Cutter jam.
What to Do
Review the User Manual command sets.
Un-adapted partial cut setting
Paper used is too thick.
Intrusion of external object.
Contact your authorized service representative.
Contact your authorized service representative.
Auto-cutter: Check that the mobile blade does not interfere with the cover blade.
Remove the Paper jam button. Using a screwdriver; turn the gear until the blade disappears.
Then open the cover and check that there is no paper jam.
Important
: Do not press on the switch when the cover is opened.
Then close the cover.
If the LED is still flashing, see LED diagnostic.
Then close the cover.
If the LED is still flashing, see LED diagnostic.
9 CLEANING YOUR PRINTER
Depending on the environment in which the printer is used, it can accumulate dust. Therefore it is necessary to clean it periodically to maintain a good print quality. The cleaning period depends on the environment and the usage of the printer, but the print head should be cleaned at least once a year or up to one month in heavy duty applications.
Cleaning Instructions:
Unplug the printer.
Never clean the head immediately after printing, the head may be hot.
Open the cover, clean the heating dots line of the head with a cotton stick containing a solvent alcohol (ethanol, methanol, or IPA) but
do not touch the print head with your fingers
!
Allow the solvent to dry and close the cover.
N.B
AXIOHM can provide cleaning kits Ref: CK60000A
TPOS PRINTER SERIES Set-up Guide
Page 12 / 12
Reference: FDE-3107243 Issue A
Downloaden
Advertentie