OptiClean

™

U S E R ’ S G U I D E

6 0 A 4 S E R I E S 2 2 0 - 2 4 0 v

3

Safety Instructions

4

Product View

5

Assembly

6-8

Operations

9-12

Maintenance and Care

13

Troubleshooting

14

Consumer Services

15

Replacement Parts

16

Warranty

T hanks for buying a BISSELL OptiClean™ Cyclonic Bagless Canister Vacuum

We’re glad you purchased a BISSELL OptiClean cyclonic bagless canister vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system.

Your BISSELL canister vacuum is well made, and we back it with a limited two year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your BISSELL canister vacuum .

Thanks again, from all of us at BISSELL.

Mark J. Bissell

President and Chief Executive Officer

2

2 w w w . b i s s e l l . c o m

I

MPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including the following:

■ Remove plug from electrical outlet before cleaning or maintaining the appliance.

READ All InStRUctIonS bEfoRE USInG yoUR cAnIStER vAcUUM.

■ If the supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard.

■ Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, petrol, etc.).

■ Do not use for any purpose other than described in this User’s Guide.

WARnInG:

to reduce the risk of fire, electric shock, or injury:

■ Use only manufacturer’s recommended attachments.

■ Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

■ Keep appliance on a level surface.

■ Turn off all controls before unplugging.

■ Use indoors only.

■ Be extra careful when cleaning stairs.

■ For dry pick up only.

■ Do not leave machine when it is plugged in.

■ This appliance is provided with double insulation. Use only identical replacement parts.

■ Do not use with damaged cord or plug.

■ If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service agent.

■ Do not use without the dirt cup or a dust bag and filters in place.

■ Pay close attention when working around children.

■ Do not handle unit with wet hands.

■ Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners or edges, run appliance over cord, or expose cord to heated surfaces.

■ Do not unplug by pulling on cord. Unplug by grasping plug.

SAvE tHESE

InStRUctIonS.

ThIs moDel Is FoR hoUseholD Use oNlY.

■ Do not run appliance over cord.

■ Do not handle plug or appliance with wet hands.

■ Do not expose hair, loose clothing, fingers or body parts to openings or moving parts.

IMPoRtAnt

FoR oPeRATIoN oN A 220-240 VolT A.C. 50/60 hz

PoWeR sUPPlY oNlY.

■ Do not pick up hot or burning objects such as cigarettes, matches, or hot ashes.

■ Do not pick up flammable or combustible materials

(lighter fluid, petrol, kerosene, etc.) or use in the presence of explosive liquids or vapour.

If your appliance is fitted with a nonrewireable Bs

1363 plug it must not be used unless a 13 amp (AsTA approved to Bs 1362) fuse is fitted in the carrier contained in the plug. (spares may be obtained from your BIssell supplier). If for any reason the plug is cut off, it must be disposed of, as it is an electric shock hazard should it be inserted into a mains socket.

■ Do not use appliance in an enclosed space filled with vapours given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapours.

■ Not intended for use by persons (including children) with reduced sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety

■ Young children should be supervised to ensure that they do not play with the appliance.

w w w . b i s s e l l . c o m

3

Swivel Hose

Easy Empty

Dirt Cup

Clean Filter

Indicator

P

roduct view

Flex Hose

Handle

Air Flow Regulator

Carry

Handle

Telescoping Extension Wand

Power

Button

Brush Switch

Post-Motor HEPA

Media Filter

Upholstery Tool Crevice Tool Dusting Brush

Attachment

Automatic

Cord Rewind

Button

Variable Suction

Power Control

Multi-Surface

Floor Nozzle

cAUtIon:

Do not plug in your vacuum until you are familiar with all instructions and operating procedures.

4

w w w . b i s s e l l . c o m

A

ssembling your vacuum

1. Connect swivel hose by squeezing both locking buttons and inserting it into the suction opening on the canister. Once the swivel hose is inserted in the suction opening, release the locking buttons.

2. Connect telescoping extension wand to the handle end of the flex hose. Twist slightly to tighten.

3. Connect floor nozzle to the end of the telescoping extension wand. Twist slightly to tighten.

4. Once assembled, you can store your vacuum in one of two positions:

A. Storing in the in-use position:

1. To store with the floor nozzle attached, insert the storage clip (located on the back of the floor nozzle) into the storage slot on the rear of the vacuum.

2. To store without the floor nozzle attached, insert the storage clip (located on the bottom of the telescoping extension wand) into the storage slot on the rear of the vacuum.

b. Storing in the upright position:

1. To store with the floor nozzle attached, stand the vacuum in the upright position and insert the storage clip (located on the back of the floor nozzle) into the storage slot on the bottom of the vacuum.

2. To store without the floor nozzle attached, stand the vacuum in the upright position and insert the storage clip (located on the bottom of the telescoping extension wand) into the storage slot on the bottom of the vacuum.

1.

A1.

b1.

WARnInG:

Plastic film can be dangerous. to avoid danger of suffocation, keep away from babies and children.

2.

3.

Storing in the in-use position

A2.

Storing in the upright position b2.

w w w . b i s s e l l . c o m

5

O

perations

Power cord

the power cord is located at the rear of the vacuum. Gently pull out the power cord, watching for the yellow line. Stop pulling the power cord once the yellow line is visible. there is also a red line, which indicates the end of the usable cord. Do not pull the power cord out beyond the red line.

Automatic cord rewind

your vacuum is equipped with an automatic cord rewind. When cleaning is finished, press the power button off and grasp the plug to disconnect from the electrical outlet. Hold the plug and press the automatic cord rewind button to rewind the cord automatically.

Power button

turn the power on or off by pressing lightly downward on the power button ( ).

Automatic

Cord Rewind

Button

Power Button

cAUtIon:

be careful to avoid injury as cord retracts very quickly.

cAUtIon:

before using your vacuum, make sure that either the dirt cup or a dust bag and all filters are in place. Do not operate your vacuum without the dirt cup or dust bag and filters.

6

w w w . b i s s e l l . c o m

O

perations

Special tools

your bISSEll opticlean is not only a powerful carpet and rug vacuum cleaner, it’s also a versatile bare floor vacuum cleaner and above floor vacuum cleaner when you select one of the special tools.

floor nozzle:

Use to vacuum carpets, rugs and bare floors.

Swivel head turns to get into tight spaces and fits under cabinets.

1.

Tip:

Before cleaning under low furniture, check area first for objects that might harm the unit or block the hose.

1. To vacuum carpets and rugs, push the brush switch to the carpet position . This will pull the brushes up into the floor nozzle.

2. To vacuum bare floors, push the brush switch to the bare floor position .

This will extend the brushes down from the floor nozzle.

Upholstery tool:

Use the upholstery tool to clean curtains, draperies, cushions and fabrics.

Dusting brush attachment:

Attach the dusting brush attachment to the upholstery tool to dust furniture, blinds, books, lamps, shelves and baseboards.

crevice tool:

Use the crevice tool in tight, narrow spaces.

2.

Tip:

Use the air flow regulator to reduce air flow as needed when using the tools.

Tip:

Hair, string and small objects can block the hose and tools.

Check them occasionally for obstructions.

Brush Up

Brush Down w w w . b i s s e l l . c o m

7

O

perations

Variable suction power control

the variable suction power control is located on the back of the vacuum. turn the control toward the larger dots for maximum suction. turn the control toward the smaller dots to minimize suction for lightly soiled areas or delicate fabrics.

Air flow regulator

open the air flow regulator by sliding the regulator back towards the handle to an open position to reduce suction for delicate fabrics.

close the air flow regulator by sliding the regulator down to the closed position for full suction.

Bagless or bagged vacuum option

the bISSEll opticlean is a unique vacuum that offers the option to vacuum using a bagless dirt cup or a traditional paper bag. to use as a bagless vacuum, simply place the dirt cup inside the vacuum cleaner. to use as a bagged vacuum, attach a dust bag to the dust bag holder and place inside the vacuum cleaner.

Clean filter indicator

the clean filter indicator is located between the power button and the automatic cord rewind button. It will monitor your air flow and let you know when it is time to clean or replace your filters. If the indicator turns orange while you are vacuuming, your filters need to be cleaned or replaced (if using as a bagged vacuum, the dust bag may need to be replaced). If the indicator remains orange, even after cleaning or replacing your filters (or replacing the dust bag), turn the vacuum off and check for a clog in the hose or tools.

note: the indicator may turn orange when using the tools due to the restricted airflow. this does not necessarily mean that the filters need to be cleaned or replaced (or the dust bag is full). If the indicator does not turn off once the tool is removed, check for a clog in the hose/tools or clean or replace your filters (or replace the dust bag).

8

w w w . b i s s e l l . c o m

Clean Filter Indicator

M

aintenance and care

Emptying the dirt cup

1. Unplug the vacuum from electrical outlet.

2. Open the dirt cup/dust bag compartment by lifting up on the latch on the door on the front of the vacuum.

3. Lift the dirt cup assembly out from the vacuum.

4. Remove the top cover from the dirt cup assembly by unfastening the latch, raising the front edge and removing the top cover off of the rear hinges. Set the top cover aside.

5. Empty the dirt into a garbage container.

6. To reattach the top cover on the dirt cup, align the slots on the top cover with the hinges on the dirt cup and rotate the front cover down to the closed position. Then fasten the latch.

7. Place the dirt cup back into the vacuum.

8. Close dirt cup/dust bag compartment door and press down gently until it locks into place.

notE: the dust bag compartment door will not close without the dirt cup or a dust bag in place.

Dust bag replacement

1. Unplug the vacuum from electrical outlet.

2. Open the dirt cup/dust bag compartment by lifting up on the latch on the door on the front of the vacuum.

3. Lift out the dust bag holder and dust bag.

4. Release the dust bag from the holder by pressing the dust bag holder clip and pulling the dust bag out of the holder. Discard the used dust bag.

4a.

2.

6.

3.

4b.

WARnInG:

to reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

4.

w w w . b i s s e l l . c o m

9

M

aintenance and care

Dust bag replacement continued

5. Slide the new dust bag into the holder by inserting the dust bag into the tabs located at the bottom of the holder. Then press the dust bag holder clip, insert the dust bag and release the dust bag holder clip to hold the dust bag in place.

6. Place holder and new dust bag back into the dirt cup/dust bag compartment, making sure the entire bag is tucked in below the seal gasket.

7. Close dirt cup/dust bag compartment door and press down gently until it locks into place.

notE: the dust bag compartment door will not close without the dirt cup or a dust bag in place.

Cleaning the pre-motor filter

the pre-motor filter protects the motor from dirt and dust particles.

1. Unplug the vacuum from electrical outlet.

notIcE:

this product is intended for household use only and not for commercial or industrial use. vacuuming of dust from products like plaster, concrete or ashes will damage the motor and void the warranty.

2. Open the dirt cup/dust bag compartment by lifting up on the latch on the door at the front of the vacuum. Lift out the dirt cup or dust bag holder and dust bag.

3. Remove the filter frame from the filter holder by grasping the lip of the frame and pulling up.

Washable Pre-

Motor Filter

3.

4. Remove the filter from the filter frame and clean by hand washing in warm water. A mild detergent can be used if desired. Allow the filter to air dry thoroughly before replacing.

5. Place the filter back into the filter frame and replace back into the filter holder. notE: the filter frame should be placed so the protective frame is visible.

6. Place the dirt cup or dust bag holder and dust bag back into the dirt cup/dust bag compartment. If using a dust bag, make sure the entire bag is tucked in below the seal gasket.

7. Close dirt cup/dust bag compartment door and press down gently until it locks into place.

Tip:

For maximum cleaning performance, check the filters often and clean or replace if necessary.

WARnInG:

Do not operate cleaner with damp or wet filters or without all filters in place.

10

w w w . b i s s e l l . c o m

M

aintenance and care

Replacing the post-motor HEPA media filter

the post-motor HEPA media filter assists in the filtration process to return clean air to the room.

1. Unplug the vacuum from electrical outlet.

2.

2. Remove the filter door (located on the back of the vacuum) by pulling down on the filter door and pulling it toward you.

3. Remove the post-motor HEPA media filter by grasping the lip of the filter frame and pulling out toward you.

4. Replace the post-motor HEPA media filter with a new filter. notE: the post-motor filter is a white, pleated HEPA media filter. this filter is not washable and must be replaced when it becomes dirty.

3.

Post-Motor

HEPA Media Filter

5. Replace the filter door by inserting the two tabs at the bottom of the filter door, pushing down on the bottom of the filter door and pushing it back into the vacuum.

Replacing the dirt cup HEPA media filter & cleaning the foam filter

IMPoRtAnt: Make sure the dirt cup is empty before you replace or clean these filters.

1.

1. To remove the dirt cup HEPA filter, pull down on the front snap.

2. Remove and replace as necessary. notE: the dirt cup HEPA media filter is a white, pleated HEPA media filter. this filter is not washable and must be replaced when it becomes dirty.

w w w . b i s s e l l . c o m

11

M

aintenance and care

Replacing the dirt cup HEPA media & cleaning the foam filter continued

3. The dirt cup foam filter is located between the bottom of the dirt cup and the HEPA filter. Once the HEPA filter has been removed, the foam filter can then be removed and cleaned or replaced as needed.

To clean the foam filter, wash with warm water and a mild detergent. Be sure to air dry completely before replacing this filter back in the dirt cup.

3.

4. To re-install the filters in the dirt cup, turn dirt cup upside down and replace the foam filter. Then replace the HEPA filter by inserting the tabs on the back of the filter into the slots on the bottom of the dirt cup and snap the filter back into place.

4.

Clearing clogs from the dirt cup

1. To clear clogs from the dirt cup, remove the top cover and set aside.

2. Empty the dirt into a garbage container.

3. Reach down into the dirt cup cyclone chamber to clear any dirt or debris from the cyclone and empty into a garbage container.

4. Remove the dirt cup HEPA and foam filters and set aside.

5. Remove any dirt or debris from the cyclone chamber opening.

6. If the holes in the cyclone appear to be clogged, place the cyclone chamber opening underneath running water and allow water to run through the holes in the cyclone to clear any clogs. Be sure to allow the entire dirt cup assembly to dry completely before replacing the dirt cup HEPA and foam filters.

3.

5.

Cyclone

Chamber

Opening

12

w w w . b i s s e l l . c o m

T

roubleshooting

vacuum cleaner won’t run

Possible causes

1. Vacuum cleaner is not plugged in

2. Power button is not pressed down

WARnInG:

to reduce the risk of electric shock, turn power off and disconnect plug from electrical outlet before performing maintenance or troubleshooting.

Remedies

1. Check electrical plug

2. Press power button down vacuum cleaner won’t pick up or low suction

Possible causes

1. Tools, flex hose and/or telescoping extension wand are blocked

2. Filters are dirty

Remedies

1. Remove each part and check for blockages

3. Dirt cup is full

2. Check and clean or replace all filters

3. Empty dirt cup

4. Dust bag is full 4. Replace with new dust bag

5. Swivel hose not securely attached to suction opening 5. Make sure swivel hose is locked into

suction opening vacuum cleaner won’t pick up or low suction

Possible causes Remedies

6. Crack or hole in flex hose

7. Air flow regulator or variable suction power control is set to open or minimum setting

6. Check hose and replace if needed

7. Change to closed or maximum setting visible dust escaping from vacuum

Possible causes Remedies

1. Dirt cup is full

2. Dust bag is full

3. Filters missing or installed incorrectly

1. Empty dirt cup

2. Replace with new dust bag

3. Check all filters for correct installation

4. Filters are dirty

5. Flex hose is blocked

4. Check and clean or replace all filters

5. Remove hose and check for

blockages

6. Swivel hose not securely attached to suction opening 6. Make sure swivel hose is locked into

suction opening

7. Crack or hole in flex hose 7. Check hose and replace if needed other maintenance or service not included in the manual should be performed by an authorized service representative.

thank you for selecting a bISSEll product.

Please do not return this product to the store.

w w w . b i s s e l l . c o m

13

0844-888-6644

42 Rocco Drive

Scoresby 3179

Victoria

Australia

9

5

1

R

eplacement parts - BISSELL OptiClean

Item

1

6

7

8

9

2

3

4

5

10

11

12

Part no.

203-7289

203-7259

203-7258

203-7263

203-7260

203-7261

203-7267

203-7257

203-7256

203-7265

203-7266

203-7264

Part name

Dirt Cup Assembly

Dirt Cup hePA media Filter

Dirt Cup Foam Filter

Dust Bag (3pk)

Pre-motor Filter

Post-motor hePA media Filter

Floor Nozzle

Flexible hose with handle

Telescoping extension Wand

Upholstery Brush

Dusting Brush Attachment

Crevice Tool

2 3 4

6 7 8

10 11 12 w w w . b i s s e l l . c o m

15

0844-888-6644

42 Rocco Drive

Scoresby 3179

Victoria

Australia