advertisement
technical data
REQ-B8V3B_REQ-B8W1B
Pair Application
Split
Sky Air
Split - Sky Air
Daikin’s unique position as a manufacturer of air conditioning equipment, compressors and refrigerants has led to its close involvement in environmental issues. For several years Daikin has had the intention to become a leader in the provision of products that have limited impact on the environment. This challenge demands the eco design and development of a wide range of products and an energy management system, resulting in energy conservation and a reduction of waste.
ISO14001 assures an effective environmental management system in order to help protect human health and the environment from potential impact of our activities, products and services and to assist in maintaining and improving the quality of the environment.
Daikin Europe N.V. is approved by LRQA for its
Quality Management System in accordance with the ISO9001 standard. ISO9001 pertains to quality assurance regarding design, development, manufacturing as well as to services related to the product.
Daikin units comply with the European regulations that guarantee the safety of the product.
“The present publication is drawn up by way of information only and does not constitute an offer binding upon Daikin Europe N.V.. Daikin
Europe N.V. has compiled the content of this publication to the best of its knowledge. No express or implied warranty is given for the completeness, accuracy, reliability or fitness for particular purpose of its content and the products and services presented therein. Specifications are subject to change without prior notice. Daikin Europe N.V.
explicitly rejects any liability for any direct or indirect damage, In the broadest sense, arising from or related to the use and/or interpretation of this publication. All content is copyrighted by Daikin Europe
N.V..”
Daikin Europe N.V. participates in the Eurovent
Certification Programme for Air Conditioners
(AC), Liquid Chilling Packages (LCP) and Fan Coil units (FC); the certified data of certified models are listed in the Eurovent Directory.
Naamloze Vennootschap
Zandvoordestraat 300
B-8400 Ostend, Belgium www.daikin.eu
BTW: BE 0412 120 336
RPR Oostende
EEDEN0 7
technical data
REQ-B8V3B_REQ-B8W1B
Pair Application
Split
Sky Air
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
TABLE OF CONTENTS
REQ-B8V3B_REQ-B8W1B
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Nominal Capacity and Nominal Input
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Dimensional drawing & centre of gravity
. . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
• Split Sky Air • Outdoor Units 4
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
1 Features
Q E y n R _ U k B 3 S V a 8 o o 0 B 1 d 4 Q p u E R R S O • Outdoor units for pair application
• Daikin outdoor units are neat and sturdy and can be mounted easily on a roof or terrace or simply placed against an outside wall.
• Outdoor units are fitted with a scroll compressor, renowned for low noise and high energy efficiency.
• The piping connections can be accessed from underneath, front, side or rear.
• The sevice valves are hidden inside the casing.
• A special acryl precoated fin for anti-corrosion treatment on the heat exchanger ensures greater resistance against severe weather conditions
1
1
5 • Split Sky Air • Outdoor Units
2
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
Specifications
2-1 NOMINAL CAPACITY AND NOMINAL INPUT
For combination indoor units + outdoor units
Nominal
Capacity
For combination indoor units + outdoor units
Indoor Units
Cooling
Heating
Nominal input Cooling
Heating
EER
COP
Energy
Labeling
Directive
Nominal
Capacity
Standard
Standard
Standard
Standard
Cooling
Heating
Cooling
Heating kW kW kW kW
Annual energy consumption kWh
Indoor Units
Cooling
Heating
Standard
Standard kW kW
Nominal input Cooling
Heating
For combination indoor units + outdoor units
EER
COP
Energy
Labeling
Directive
Nominal
Capacity
Standard
Standard
Cooling
Heating
Cooling
Heating kW kW
Annual energy consumption kWh
Indoor Units
Cooling
Heating
Standard
Standard kW kW
Nominal input Cooling
Heating
For combination indoor units + outdoor units
EER
COP
Energy
Labeling
Directive
Nominal
Capacity
Standard
Standard
Cooling
Heating
Cooling
Heating kW kW
Annual energy consumption kWh
Indoor Units
Cooling
Heating
Standard
Standard kW kW
Nominal input Cooling
Heating
For combination indoor units + outdoor units
EER
COP
Energy
Labeling
Directive
Standard
Standard
Cooling
Heating
Cooling
Heating kW kW
Annual energy consumption kWh
REQ71B8V3B
FDEQ71B8V3B
D
1350
1360
FBQ71B8V3B
7.1
8
2.79
2.49
2.54
3.21
E
C
1395
FHQ71BVV1B
7.1
8
2.7
2.85
2.63
2.81
1395
FCQ71C7VEB
7.1
8
2.79
2.49
2.54
3.21
E
C
2.54
3.21
E
C
7.1
8
2.79
2.49
2-2 TECHNICAL SPECIFICATIONS
Casing
Dimensions
Colour
Material
Unit
Packing
Height
Width
Depth
Height
Width
Depth
Weight Unit
Packed Unit mm mm kg kg mm mm mm mm
REQ71B8V3B
980
420
83
87
770
900
320
900
REQ71B8W1B
FDEQ71B8V3B
REQ100B8V3B
FDEQ100B8V3B
REQ100B8W1B
FDEQ100B8V3B
REQ125B8W1B
FDEQ125B8V3B
1330
FBQ71B8V3B
7.1
8
2.68
2.49
2.65
3.21
D
C
1340
FHQ71BVV1B
7.1
8
2.65
2.8
2.68
2.86
1340
FCQ71C7VEB
7.1
8
2.66
2.80
2.67
2.86
D
C
2.65
3.21
D
C
7.1
8
2.68
2.49
D
1325
9.8
11.2
3.98
3.99
2.46
2.81
E
D
1990
FCQ100C7VEB
10
11.2
3.83
3.75
2.61
2.99
D
1915
FBQ100B8V3B
10
11.2
3.79
3.91
2.64
2.86
D
D
1895
FHQ100BVV1B
9.8
11.2
3.75
4.13
2.61
2.71
D
E
1875
980
420
83
87
770
900
320
900
REQ71B8W1B REQ100B8V3B
Daikin White
Painted galvanized steel plate
1170
900
320
1300
980
420
102
107
REQ100B8W1B
1170
900
320
1300
980
420
100
105
1780
FBQ100B8V3B
10
11.2
3.6
3.87
2.78
2.89
D
D
1800
FHQ100BVV1B
9.8
11.2
3.68
4.01
2.66
2.79
2.49
2.83
E
D
9.8
11.2
3.94
3.96
1970
FCQ100C7VEB
10
11.2
3.56
3.66
2.81
3.06
C
D
E
1840
2.68
3.23
D
C
12.5
14.5
4.67
4.52
2335
FCQ125C7VEB
12.5
14.6
4.66
5.06
2.68
2.89
D
1170
900
320
1300
980
420
108
113
2330
FBQ125B8V3B
12.2
14.5
4.67
4.52
2.61
3.21
D
C
2335
FHQ125BVV1B
12.2
14.5
4.51
5.16
2.71
2.81
D
2255
REQ125B8W1B
• Split Sky Air • Outdoor Units
1
2
6
2
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
Specifications
1
2
2-2 TECHNICAL SPECIFICATIONS
Heat
Exchanger
Fan
Motor
Fan
Motor
Fan
Compressor
Operation
Range
Sound Level
(nominal)
Dimensions
Cooling
Length
Nr of Rows
Fin Pitch
Nr of Passes mm mm
Face Area m²
Nr of Stages
Tube type
Fin
Type
Discharge direction
Type
Treatment
Quantity
Air Flow Rate
(nominal at
230V)
Motor
Cooling
Heating
Quantity
Model
Position
Steps Speed
(nominal)
Motor Output
Position
Steps Speed
(nominal)
Motor
Quantity
Motor
Output
Model
Type
Motor
Output
Crankcase
Heater m³/min m³/min
W
W
W
W
Heating
Cooling
Min
Max
Min
Max
Sound
Power
Sound
Pressure
°CDB
°CDB
°CWB
°CWB dBA dBA
Refrigerant Type
Charge
Control
Nr of Circuits
Refrigerant Oil Type
Charged Volume l kg
REQ71B8V3B
857
2
2.00
6
0.641
34
1
48.0
43.0
1
3
65
1
JT90G-P4V1N@S
2200
33
10.0
46.0
-10
15
65.0
53.0
2.5
1
1.5
REQ71B8W1B
857
2
2.00
6
0.641
34
1
48.0
43.0
REQ100B8V3B
857
2
2.00
10
0.980
52
Hi-XSS cooling tube
Non-symmetric waffle louvre
Anti-corrosion treatment (PE)
Direct Drive Propeller
Horizontal
1
55.0
50.0
REQ100B8W1B
857
2
2.00
10
0.980
52
1
55.0
50.0
1 1
P47L11S
1
3
65
3
90
3
90
1
JT90G-YE
2200
1
JT125G-P4V1@S
Hermetically sealed scroll compressor
3000
1
JT125G-YE
3000
33 33 33
10.0
46.0
-10
15
65.0
53.0
10.0
46.0
-10
15
70.0
57.0
10.0
46.0
-10
15
70.0
57.0
2.5
1
1.5
R-410A
3.6
Expansion valve (electronic type)
1
Daphne FVC68D
1.5
3.6
1
1.5
REQ125B8W1B
857
2
2.00
10
0.980
52
2
89.0
80.0
1
Lower
3
85
Upper
3
65
1
JT160G-YE
3750
33
10.0
46.0
-10
15
70.0
57.0
3.6
1
1.5
7 • Split Sky Air • Outdoor Units
2
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
Specifications
2-2 TECHNICAL SPECIFICATIONS
Piping connections
Liquid (OD)
Gas mm mm
Drain Quantity
Type
Diameter
(OD) mm
Piping Length Minimum m
Maximum m
Installation height difference
Equivalent m
Chargeless m
Maximum m
Max. internunit level difference
Heat Insulation m
Defrost Method
Defrost Control
Capacity Control Method
Safety Devices
Quantity
Type
Diameter
(OD)
Quantity
Type
Diameter
(OD)
Standard
Accessories
Item
Quantity
Item
Quantity
Notes
REQ71B8V3B
1
9.52
1
15.9
3
26
5
50
70
7.5
30.0
REQ71B8W1B
1
9.52
1
15.9
3
26
5
50
70
7.5
30.0
REQ100B8V3B
1
Flare connection
9.52
1
Flare connection
15.9
3
Hole
26
5
50
70
7.5
30.0
REQ100B8W1B
1
9.52
1
15.9
3
26
5
50
70
7.5
30.0
0.5
0.5
0.5
0.5
0.5
Both liquid and gas pipes
Reversed cycle
Sensor for outdoor heat exchanger temperature
None
Reverse phase protector
PC board fuse
Overcurrent relay (compressor)
Low pressure switch
High pressure switch
Fan motor thermal protector
Declaration of conformity
1 1 1 1 1
1 1
Installation manual
1 1 1
Sound pressure level is a relative value, depending on the distance and acoustic environment. For more details, please refer to sound level drawings of this chapter.
The sound power level is an absolute value indicating the power which a sound source generates.
Sound values are measured in a semi-anechoic room.
In case of drain piping for outdoor unit, drain piping kit (option) is needed.
Nominal cooling capacities are based on : indoor temperature : 27°CDB, 19°CWB, outdoor temperature : 35°CDB, equivalent refrigerant piping : 7.5m, level difference : 0m.
Nominal heating capacities are based on : indoor temperature : 20°CDB, outdoor temperature : 7°CDB, 6°CWB, equivalent refrigerant piping : 7.5m, level difference : 0m
REQ125B8W1B
1
9.52
1
15.9
3
26
5
50
70
7.5
30.0
2-3 ELECTRICAL SPECIFICATIONS
Power Supply Name
Phase
Current
Wiring connections
Frequency
Voltage
Voltage range Minimum V
Maximum V
Recomended fuses
For Power
Supply
Quantity
Remark
Hz
V
A
For connection with indoor
Power Supply Intake
Quantity
Remark
REQ71B8V3B
V3
1
50
230
32
1
3 wires (earth wire included)
1
REQ71B8W1B REQ100B8V3B REQ100B8W1B
W1
3N
50
400
V3
1
50
230
W1
3N
50
400
16
1
-10%
+10%
40
1
5 wires (earth wire included)
1
3 wires (earth wire included)
1
4 wires (earth wire included)
5 wires (earth wire included)
1
Outdoor unit only
16
1
REQ125B8W1B
W1
3N
50
400
20
1
5 wires (earth wire included)
1
• Split Sky Air • Outdoor Units
1
2
8
1
3
3
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
Electrical data
Indoor unit
Unit combination
Outdoor unit
FCQ71B
FCQ71C
REQ71B8V3B
REQ71B8V3B
FHQ71
FBQ71
FDEQ71
FCQ71B
REQ71B8V3B
REQ71B8V3B
REQ71B8V3B
REQ71B8W1B
FCQ71C
FHQ71
FBQ71
FDEQ71
REQ71B8W1B
REQ71B8W1B
REQ71B8W1B
REQ71B8W1B
SYMBOLS
MCA : Min. Circuit Amps
TOCA : Total Over Current Amps
MFA
LRA
: Max. Fuse Amps (see note 7)
: Locked Rotor Amps
RLA
OFM
IFM
FLA kW
: Rated Load Amps
: Outdoor Fan Motor
: Indoor Fan Motor
: Full Load Amps
: Rated motor output
Hz-Volts
50-230
50-230
50-230
50-230
50-230
50-400
50-400
50-400
50-400
50-400
Power supply
Voltage range
Max. 50Hz-253V
Min. 50Hz-207V
Max. 50Hz-440V
Min. 50Hz-360V
8.1
6.8
7.1
7.5
17.4
15.4
7.3
MCA TOCA
16.6
23.3
16.4
16.8
23.1
23.2
23.5
23.5
11.3
11.1
11.2
11.5
11.5
MFA
32
32
32
32
32
16
16
16
16
16
41.1
41.1
41.1
41.1
75.5
75.5
75.5
41.1
Compressor
LRA RLA
75.5
75.5
12.2
12.2
12.5
12.7
11.1
4.8
5.3
4.2
4.8
5.0
0.065
0.065
0.065
0.065
0.065
0.065
0.065
0.065
kW
OFM
FLA
0.065
0.065
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.065
0.062
0.125
0.125
0.062
0.125
0.125
0.045
kW
IFM
FLA
0.045
0.065
0.7
0.5
0.6
0.9
0.9
0.7
0.9
0.9
0.5
0.6
3TW26599-9A
NOTES
1. RLA is based on the following conditions:
Indoor temp.: 27°CDB/19.0°CWB
Outdoor temp. : 35°CDB
2. TOCA means the total value of each OC set
3. Voltage range
Units are suitable for use on electrical systems where voltage supplied to unit terminals is not below or above listed operation range limits
4. Maximum allowable voltage unbalance between phases is 2%.
5. MCA/MFA
MCA = 1.25 x RLA + all FLA, MFA = < 2.25 x RLA + all FLA (next lower standard fuse rating Min. 16A)
6. Select wire size based on the larger value of MCA or TOCA
7. Instead of fuse, use circuit breaker
8. For more details concerning conditional connections, see http://www.daikineurope.com/extranet, select ’’Daikin Documentation’’ and select
’’conditional connection’’, ’’the requested product type’’ and ’’English’’ from the drop down lists, click the search button.
Finally, click on the document title of your choice.
9 • Split Sky Air • Outdoor Units
3
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
Electrical data
Indoor unit
Unit combination
Outdoor unit
FCQ100B
FCQ100C
REQ100B8V3B
REQ100B8V3B
FHQ100
FBQ100
FDEQ100
FCQ100B
REQ100B8V3B
REQ100B8V3B
REQ100B8V3B
REQ100B8W1B
FCQ100C
FHQ100
FBQ100
FDEQ100
REQ100B8W1B
REQ100B8W1B
REQ100B8W1B
REQ100B8W1B
Hz-Volts
50-230
50-230
50-230
50-230
50-230
50-400
50-400
50-400
50-400
50-400
SYMBOLS
MCA : Min. Circuit Amps
TOCA : Total Over Current Amps
MFA
LRA
: Max. Fuse Amps (see note 7)
: Locked Rotor Amps
RLA
OFM
IFM
FLA kW
: Rated Load Amps
: Outdoor Fan Motor
: Indoor Fan Motor
: Full Load Amps
: Rated motor output
Power supply
Voltage range
Max. 50Hz-253V
Min. 50Hz-207V
Max. 50Hz-440V
Min. 50Hz-360V
8.9
9.6
8.9
9.4
23.2
24.2
9.2
MCA TOCA
23.8
34.8
23.5
25.3
34.5
34.5
34.8
34.8
11.8
11.5
11.5
11.8
11.8
MFA
40
40
40
40
40
16
16
16
16
16
48.2
48.2
48.2
48.2
98.5
98.5
98.5
48.2
Compressor
LRA RLA
98.5
98.5
17.6
17.6
19.0
17.1
17.9
4.8
5.3
4.2
4.8
5.0
0.090
0.090
0.090
0.090
0.090
0.090
0.090
0.090
kW
OFM
FLA
0.090
0.090
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.120
0.130
0.135
0.135
0.130
0.135
0.135
0.090
kW
IFM
FLA
0.090
0.120
1.0
0.7
0.7
1.0
1.0
1.0
1.0
1.0
0.7
0.7
3TW26619-9A
NOTES
1. RLA is based on the following conditions:
Indoor temp.: 27°CDB/19.0°CWB
Outdoor temp. : 35°CDB
2. TOCA means the total value of each OC set
3. Voltage range
Units are suitable for use on electrical systems where voltage supplied to unit terminals is not below or above listed operation range limits
4. Maximum allowable voltage unbalance between phases is 2%.
5. MCA/MFA
MCA = 1.25 x RLA + all FLA, MFA = < 2.25 x RLA + all FLA (next lower standard fuse rating Min. 16A)
6. Select wire size based on the larger value of MCA or TOCA
7. Instead of fuse, use circuit breaker
8. For more details concerning conditional connections, see http://www.daikineurope.com/extranet, select ’’Daikin Documentation’’ and select
’’conditional connection’’, ’’the requested product type’’ and ’’English’’ from the drop down lists, click the search button.
Finally, click on the document title of your choice.
1
3
• Split Sky Air • Outdoor Units 10
1
3
3
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
Electrical data
Indoor unit
Unit combination
Outdoor unit
FCQ125B REQ125B8V3B
FCQ125C REQ125B8V3B
FHQ125
FBQ125
FDEQ125
REQ125B8V3B
REQ125B8V3B
REQ125B8V3B
SYMBOLS
MCA : Min. Circuit Amps
TOCA : Total Over Current Amps
MFA : Max. Fuse Amps (see note 7)
LRA
RLA
OFM
: Locked Rotor Amps
: Rated Load Amps
: Outdoor Fan Motor
IFM
FLA kW
: Indoor Fan Motor
: Full Load Amps
: Rated motor output
Hz-Volts
50-400
50-400
50-400
50-400
50-400
Power supply
Voltage range
Max. 50Hz-400V
Min. 50Hz-360V
MCA TOCA
12.4
15.3
MFA
20
12.4
12.3
12.2
12.6
15.3
15.0
15.7
15.7
20
20
20
20
Compressor
LRA RLA
63 8.1
63
63
63
63
8.1
8.2
7.6
7.9
0.065
+0.085
0.065
+0.085
0.065
+0.085
kW
OFM
FLA
0.065
+0.085
0.065
+0.085
0.6+0.7
0.6+0.7
kW
0.09
0.12
IFM
FLA
1.0
1.0
0.6+0.7
0.6+0.7
0.6+0.7
0.13
0.225
0.225
0.7
1.4
1.4
3TW26639-9A
NOTES
1. RLA is based on the following conditions:
Indoor temp.: 27°CDB/19.0°CWB
Outdoor temp. : 35°CDB
2. TOCA means the total value of each OC set
3. Voltage range
Units are suitable for use on electrical systems where voltage supplied to unit terminals is not below or above listed operation range limits
4. Maximum allowable voltage unbalance between phases is 2%.
5. MCA/MFA
MCA = 1.25 x RLA + all FLA, MFA = < 2.25 x RLA + all FLA (next lower standard fuse rating Min. 16A)
6. Select wire size based on the larger value of MCA or TOCA
7. Instead of fuse, use circuit breaker
8. For more details concerning conditional connections, see http://www.daikineurope.com/extranet, select ’’Daikin Documentation’’ and select
’’conditional connection’’, ’’the requested product type’’ and ’’English’’ from the drop down lists, click the search button.
Finally, click on the document title of your choice.
11 • Split Sky Air • Outdoor Units
4
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
Safety device settings
REQ71 ∼ 125B
Safety device
Fan motor thermal protector
HPS
LPS
Max discharge temperature
Overcurrent relay
Model
REQ71BV3
REQ71BW1
REQ100BV3
REQ100BW1
Off 135 ±5°C
On 95 ±15°C
Off 4,15
On 3.2
+0
- 0,10
Mpa
+0,15
- 0,15
Mpa
Off -0.03
+0,02
- 0,02
Mpa
On 0.05
+0,03
- 0,03
Mpa
By thermistor and software control
By overcurrent sensor and software control
REQ125BW1
4TW26321-2B
• Split Sky Air • Outdoor Units
1
4
12
5 Options
REQ71 ∼125B
Name of option
Central drain plug
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
REQ71B
Kit name
REQ100B
KKPJ5F180
REQ125B
4TW26599-1
1
5
13 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 1 Cooling capacity tables
FHQ71-125B + REQ71-100BV3
REQ71-125BW1
Cooling capacity table
Outdoor
Indoor
EWB EDB
(°C) (°C) TC
20
SHC PI TC
25
SHC PI TC
32
SHC
Outdoor temp. (°CDB)
PI TC
35
SHC PI TC
40
SHC PI TC
46
SHC PI
SYMBOLS
AFR: Air flow rate
BF: Bypass factor
EWB: Entering wet bulb temp.
EDB: Entering dry bulb temp.
DB*: Dry bulb temp.
TC: Total cooling/heating capacity
SHC: Sensible heating capacity
PI: Power input
(comp.+indoor+outdoor fan motor)
Caution:
TC and SHC are shown by kW
V3: 230 V [50 Hz]
W1: 400 V [50 Hz]
(m 3 /min)
(°CWB)
(°CDB)
(°CDB)
(kW)
(kW)
(kW)
NOTES
1. Ratings shown are net capacities.
Influence of fan motor heat is included.
2.
Shows nominal capacities
3. SHC is based on each EWB and EDB
SHC* = SHC correction for other dry bulb
SHC* = 0.29 x 60 x AFR (m 3 /min.) x (1 −BF) x (DB*−EDB)/860
Add SHC* to SHC if SHC > TC, then TC equal SHC
4. Direct interpolation is permissible.
Do not extrapolate.
5. Capacities are based on following conditions:
Corresponding refrigerant piping length
Level difference
6. Air flow rate and BF are tabulated below.
: 7.5 m
: 0 m
Model
71
100
125
AFR
BF
AFR
BF
AFR
BF
FHQ
17
0.1
24
0.14
30
0.13
7. Add the following corrections to power input of each model.
Model
71
100
125
Supply
V3
W1
V3
W1
W1
FHQ
0.05
0
0.07
0
0
3TW26592-3
1
6
• Split Sky Air • Outdoor Units 14
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 1 Cooling capacity tables
Cooling capacity table
FCQ71-125C7VEB+ REQ71-100B8V3B
REQ71-125B8W1B
Outdoor
Indoor
EWB EDB
(°C) (°C) TC
20
SHC PI TC
25
SHC PI TC
32
SHC
Outdoor temperature (°CDB)
PI TC
35
SHC PI TC
40
SHC PI TC
46
SHC PI
1
6
SYMBOLS
AFR: Air flow rate
BF: Bypass factor
EWB: Entering wet bulb temp.
EDB: Entering dry bulb temp.
(m 3 /min)
(°CWB)
(°CDB)
DB*:
TC:
Dry bulb temp.
Total capacity
SHC: Sensible heating capacity
PI:
(°CDB)
(kW)
(kW)
Power input (Comp. + indoor + outdoor fan motor). (kW)
Caution
TC and SHC are shown by kW
V3: 230V (50Hz)
W1: 400V (50Hz)
1
2
3
4
5
6
7
3D057263
NOTES
Ratings shown are net capacities which include a deduction for indoor fan motor heat
Shows nominal capacities
SHC is based on each EWB and EDB
SHC* = SHC correction for other dry bulb
= 0.29 x 60 x AFR [m 3 /min.] x (1-BF) x (DB*-EDB)/860
Add SHC* to SHC if SHC > TC, then TC equal SHC
Direct interpolation is permissible.
Do not extrapolate.
Capacities are based on following conditions:
Corresponding refrigerant piping length:
Level difference:
5 m
0 m
Air flow rate (AFR) and Bypass factor (BF) are taburated below.
Model
71
100
125
AFR
BF
AFR
BF
AFR
BF
FBQ
15.5
0.19
23.5
0.16
27.5
0.19
Add the following corrections to power input of each model.
Model
71
100
125
Supply
V3
W1
V3
W1
W1
FBQ
0.06
0
0.27
0
0
15 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 1 Cooling capacity tables
FBQ71-125B + REQ71-100BV3
REQ71-125BW1
Cooling capacity table
Outdoor
Indoor
EWB EDB
(°C) (°C) TC
20
SHC PI TC
25
SHC PI TC
32
SHC
Outdoor temp. (°CDB)
PI TC
35
SHC PI TC
40
SHC PI TC
46
SHC PI
SYMBOLS
AFR: Air flow rate
BF: Bypass factor
EWB: Entering wet bulb temp.
EDB: Entering dry bulb temp.
DB*: Dry bulb temp.
TC: Total cooling/heating capacity
SHC: Sensible heating capacity
PI: Power input
(comp.+indoor+outdoor fan motor)
Caution:
TC and SHC are shown by kW
V3: 230 V [50 Hz]
W1: 400 V [50 Hz]
(m 3 /min)
(°CWB)
(°CDB)
(°CDB)
(kW)
(kW)
(kW)
NOTES
1. Ratings shown are net capacities.
Influence of fan motor heat is included.
2.
Shows nominal capacities
3. SHC is based on each EWB and EDB
SHC* = SHC correction for other dry bulb
SHC* = 0.29 x 60 x AFR (m 3 /min.) x (1 −BF) x (DB*−EDB)/860
Add SHC* to SHC if SHC > TC, then TC equal SHC
4. Direct interpolation is permissible.
Do not extrapolate.
5. Capacities are based on following conditions:
Corresponding refrigerant piping length
Level difference
6. Air flow rate and BF are tabulated below.
: 7.5 m
: 0 m
Model
71
100
125
AFR
BF
AFR
BF
AFR
BF
FBQ
19
0.11
27
0.2
35
0.14
7. Add the following corrections to power input of each model.
Model
71
100
125
Supply
V3
W1
V3
W1
W1
FBQ
0.11
0
0.19
0
0
3TW26592-2
1
6
• Split Sky Air • Outdoor Units 16
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 1 Cooling capacity tables
FDEQ71-125B + REQ71-100BV3
REQ71-125BW1
Cooling capacity table
Outdoor
Indoor
EWB EDB
(°C) (°C) TC
20
SHC PI TC
25
SHC PI TC
32
SHC
Outdoor temp. (°CDB)
PI TC
35
SHC PI TC
40
SHC PI TC
46
SHC PI
1
6
SYMBOLS
AFR:
BF:
Air flow rate
Bypass factor
EWB: Entering wet bulb temp.
EDB:
DB*:
Entering dry bulb temp.
Dry bulb temp.
TC: Total cooling/heating capacity
SHC: Sensible heating capacity
PI: Power input
(comp.+indoor+outdoor fan motor)
Caution:
TC and SHC are shown by kW
V3: 230 V [50 Hz]
W1: 400 V [50 Hz]
(m 3 /min)
(°CWB)
(°CDB)
(°CDB)
(kW)
(kW)
(kW)
NOTES
1. Ratings shown are net capacities.
Influence of fan motor heat is included.
2.
Shows nominal capacities
3. SHC is based on each EWB and EDB
SHC* = SHC correction for other dry bulb
SHC* = 0.29 x 60 x AFR (m 3 /min.) x (1 −BF) x (DB*−EDB)/860
Add SHC* to SHC if SHC > TC, then TC equal SHC
4. Direct interpolation is permissible.
Do not extrapolate.
5. Capacities are based on following conditions:
Corresponding refrigerant piping length
Level difference
6. Air flow rate and BF are tabulated below.
: 7.5 m
: 0 m
Model
71
100
125
AFR
BF
AFR
BF
AFR
BF
FDEQ
19
0.11
27
0.2
35
0.14
7. Add the following corrections to power input of each model.
Model
71
100
125
Supply
V3
W1
V3
W1
W1
FDEQ
0.11
0
0.04
0
0
3TW26592-4
17 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 2 Heating capacity tables
FHQ71-125B + REQ71-100BV3
REQ71-125BW1
Heating capacity table
Outdoor
Indoor
EDB
(°C) TC
-10
PI TC
-5
PI TC
0 outdoor temperature (°CWB)
PI TC
6
PI TC
10
PI TC
15
PI
SYMBOLS
AFR: Air flow rate
EDB: Entering dry bulb temp.
WB: Wet bulb temperature
TC:
PI:
Total cooling/heating capacity
Power input
(comp.+indoor+outdoor fan motor)
Caution:
TC is shown by kW
V3: 230 V [50 Hz]
W1: 400 V [50 Hz]
3TW26592-7
(m 3 /min)
(°CDB)
(°CWB)
(kW)
(kW)
NOTES
1. Ratings shown are net capacities.
Influence of fan motor heat is included.
2.
Shows nominal capacities
3. Capacities are based on following conditions:
* outdoor air : 85 % RH. however, the condition on nominal capacity is 7° CDB/6° CWB
* Corresponding refrigerant piping length
Level difference
4. Direct interpolation is permissible.
: 7.5 m
: 0 m
Do not extrapolate.
5. Air flow rate and BF are tabulated below.
Model
71
100
125
AFR
BF
AFR
BF
AFR
BF
FHQ
17
0.1
24
0.14
30
0.13
6. Add the following corrections to power input of each model.
Model
71
100
125
Supply
V3
W1
V3
W1
W1
FHQ
0.05
0
0.12
0
0
1
6
• Split Sky Air • Outdoor Units 18
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 2 Heating capacity tables
Heating capacity table
FCQ71-125C7VEB+ REQ71-100B8V3B
REQ71-125B8W1B
Outdoor
Indoor
EDB
(°C) TC
-10
PI TC
-5
PI TC
0
Outdoor temperature (°CDB)
PI TC
6
PI TC
10
PI TC
15
PI
1
6
SYMBOLS
AFR:
WB: Wet bulb temperature
EDB: Entering dry bulb temp.
TC: Total capacity
PI:
Air flow rate (m 3 /min)
(°CWB)
(°CDB)
(kW)
Power input (Comp. + indoor + outdoor fan motor). (kW)
Caution
TC and SHC are shown by kW
V3: 230V (50Hz)
W1: 400V (50Hz)
1
2
3
4
5
6
3D057264
NOTES
Ratings shown are net capacities which include a deduction for indoor fan motor heat
Shows nominal capacities
Capacities are based on following conditions: outdoor air : 85 % RH. however, the condition on nominal capacity is 7° CDB/6° CWB
Corresponding refrigerant piping length:
Level difference:
5 m
0 m
Direct interpolation is permissible.
Do not extrapolate.
Air flow rate (AFR) and Bypass factor (BF) are taburated below.
Model
71
100
125
AFR
BF
AFR
BF
AFR
BF
FBQ
16.0
0.19
23.5
0.16
27.5
0.19
Add the following corrections to power input of each model.
Model
71
100
125
Supply
V3
W1
V3
W1
W1
FBQ
0.05
0
0.09
0
0
19 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 2 Heating capacity tables
FBQ71-125B + REQ71-100BV3
REQ71-125BW1
Heating capacity table
Outdoor
Indoor
EDB
(°C) TC
-10
PI TC
-5
PI TC
0 outdoor temperature (°CWB)
PI TC
6
PI TC
10
PI TC
15
PI
SYMBOLS
AFR: Air flow rate
EDB: Entering dry bulb temp.
WB: Wet bulb temperature
TC:
PI:
Total cooling/heating capacity
Power input
(comp.+indoor+outdoor fan motor)
Caution:
TC is shown by kW
V3: 230 V [50 Hz]
W1: 400 V [50 Hz]
3TW26592-6
(m 3 /min)
(°CDB)
(°CWB)
(kW)
(kW)
NOTES
1. Ratings shown are net capacities.
Influence of fan motor heat is included.
2.
Shows nominal capacities
3. Capacities are based on following conditions:
* outdoor air : 85 % RH. however, the condition on nominal capacity is 7° CDB/6° CWB
* Corresponding refrigerant piping length
Level difference
4. Direct interpolation is permissible.
: 7.5 m
: 0 m
Do not extrapolate.
5. Air flow rate and BF are tabulated below.
Model
71
100
125
AFR
BF
AFR
BF
AFR
BF
FBQ
19
0.11
27
0.2
35
0.14
6. Add the following corrections to power input of each model.
Model
71
100
125
Supply
V3
W1
V3
W1
W1
FBQ
0
0
0.04
0
0
1
6
• Split Sky Air • Outdoor Units 20
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 2 Heating capacity tables
FDEQ71-125B + REQ71-100BV3
REQ71-125BW1
Heating capacity table
Outdoor
Indoor
EDB
(°C) TC
-10
PI TC
-5
PI TC
0 outdoor temperature (°CWB)
6
PI TC PI TC
10
PI TC
15
PI
1
6
AFR:
EDB:
WB:
TC:
PI:
SYMBOLS
Air flow rate
Entering dry bulb temp.
Wet bulb temperature
Total cooling/heating capacity
Power input
(comp.+indoor+outdoor fan motor)
Caution:
TC is shown by kW
V3: 230 V [50 Hz]
W1: 400 V [50 Hz]
3TW26592-8
(m 3 /min)
(°CDB)
(°CWB)
(kW)
(kW)
NOTES
1. Ratings shown are net capacities.
Influence of fan motor heat is included.
2.
Shows nominal capacities
3. Capacities are based on following conditions:
* outdoor air : 85 % RH. however, the condition on nominal capacity is 7° CDB/6° CWB
* Corresponding refrigerant piping length
Level difference
4. Direct interpolation is permissible.
: 7.5 m
: 0 m
Do not extrapolate.
5. Air flow rate and BF are tabulated below.
Model
71
100
125
AFR
BF
AFR
BF
AFR
BF
FDEQ
19
0.11
27
0.2
35
0.14
6. Add the following corrections to power input of each model.
Model
71
100
125
Supply
V3
W1
V3
W1
W1
FDEQ
0
0
0.04
0
0
21 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
6 Capacity tables
6 - 2 Heating capacity tables
RR/RQ/REQ71 ∼ 125B
Capacity in function of field piping length for non-inverter
Capacity (%)
Cooling
Heating
Field piping length (m)
3TW26322-15
• Split Sky Air • Outdoor Units
1
6
22
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
7 Dimensional drawing & centre of gravity
7 - 1 Dimensional drawing
REQ71B
Hole for anchor bolt
4-M12
1 Gas pipe connection J15.9 flare
2 Liquid pipe connection - J9.5 flare
3 Service port (in the unit)
4 Grounding terminal M5 (in switch box)
5 Refrigerant piping intake
6 Power supply wiring intake (knock hole J34)
7 Control wiring intake (knock hole J27)
8 Drain outlet unit (mm)
1
7
REQ100B
Hole for anchor bolt
4-M12
23 • Split Sky Air • Outdoor Units
1 Gas pipe connection J15.9 flare
2 Liquid pipe connection - J9.5 flare
3 Service port (in the unit)
4 Grounding terminal M5 (in switch box)
5 Refrigerant piping intake
6 Power supply wiring intake (knock hole J34)
7 Control wiring intake (knock hole J27)
8 Drain outlet
3TW26324-1 unit (mm)
3TW26344-1
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
7 Dimensional drawing & centre of gravity
7 - 1 Dimensional drawing
REQ125B
Hole for anchor bolt
4-M12
1 Gas pipe connection J15.9 flare
2 Liquid pipe connection - J9.5 flare
3 Service port (in the unit)
4 Grounding terminal M5 (in switch box)
5 Refrigerant piping intake
6 Power supply wiring intake (knock hole J34)
7 Control wiring intake (knock hole J27)
8 Drain outlet unit (mm)
3TW26364-1
1
7
24 • Split Sky Air • Outdoor Units
1
7
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
7 Dimensional drawing & centre of gravity
7 - 2 Centre of gravity
REQ71B
REQ71B
Model A
267
3TW26329-5C
REQ100B
REQ100B
Model A
390
3TW26349-5C
25 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
7 Dimensional drawing & centre of gravity
7 - 2 Centre of gravity
REQ125B
REQ125B
Model A
390
3TW26369-5C
1
7
26 • Split Sky Air • Outdoor Units
8
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
Piping diagram
REQ71 ∼125B (Pair)
Solenoid valve
Electronic expansion valve
One way valve One way valve
Filter
Filter
One way valve One way valve
Strainer
Service port 5/16 ″
Receiver
Heat exchanger
Capillary tube
4-way valve
One way valve
Filter Low pressure switch
High pressure switch
Muffler
Field piping J9.5 C122OT-O
Filter
Field piping J15.9 C122OT-O
Compressor
Indoor unit
Stop valve
(with service port 1/4 ″ flare)
Outdoor unit
O
Check valve
L
Flare connection
M
Screw connection
N
Flange connection
Z
Pinched pipe
P
Spinned pipe
Heat exchanger
Heating
Cooling
Service port 5/16 ″
3TW26325-1
1
8
27 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
9 Wiring diagram
9 - 1 Wiring diagram
REQ71-100BV3
Power supply
1 ∼50Hz
230V
Indoor
A1P
BS1
C1R
C3R
DS1
E1HC
F1U
HAP
Printed circuit board
Push button (forced defrost-pump down)
Capacitor (M1F)
Capacitor (M1C)
DIP switch
Crankcase heater
Fuse (T6.3/250V)
Light emitting diode (service monitor green)
K1M
K1R
K2R
K3R
Magnetic contactor (M1C)
Magnetic relay (K1M)
Magnetic relay (Y2S)
Magnetic relay (E1HC)
K4R Magnetic relay (Y1S)
K5R,K6R,K7R Magnetic relay (M1F)
M1C
M1F
Motor compressor
Motor fan
PC
Q1DI
Q1M
R1T
R2T
R3T
RC
S1PH
Power circuit
Earth leakage breaker (30mA)
Thermo switch (M1F)
Thermistor (air)
Thermistor (coil)
Thermistor (discharge pipe)
Signal receiver circuit
Pressure switch (high)
S1LP
SD
T1A
TC
Pressure switch (low)
Safety devices input
Current transformer
Signal transmission circuit
X1M,X2M Terminal strip
Y1E Expansion valve (electronic type)
Y1S
Y2S
CT
4-way valve
Solenoid valve
Current transformer
Switch box
(Outdoor)
Note:
Confirm the method of setting the DIP switch (DS1) by service manual when the unit is shipped by factory all switches are set to be off.
Position of compressor terminal
Wire entrance
ON
OFF g Field wiring
D : Terminal
F : Connector b
L
: Protective earth (screw)
: Live
N : Neutral
: Terminal
Colours
BLK: Black/ BLU: Blue/ WHT: White/
RED: Red/ ORG: Orange/ YLW:Yellow
Outdoor
2TW26326-1B
REQ71-100BW1
Switch box
(Outdoor)
Indoor
Outdoor
Power supply
3N ∼50Hz
400V
Note:
Confirm the method of setting the DIP switch (DS1) by service manual when the unit is shipped by factory all switches are set to be off.
g Field wiring
D : Terminal
F : Connector b
L
: Protective earth (screw)
: Live
N : Neutral
: Terminal
Colours
BLK: Black/ BLU: Blue/ WHT: White/
RED: Red/ ORG: Orange/ YLW:Yellow
Position of compressor terminal
Wire entrance
A1P
BS1
C1
Printed circuit board
Push button (forced defrost-pump down)
Capacitor (M1F)
DS1
E1HC
DIP switch
Crankcase heater
F1U, F2U Fuse (T6.3/250V)
HAP Light emitting diode (service monitor green)
K1M
K1R
Magnetic contactor (M1C)
Magnetic relay (K1M)
K2R
K3R
K4R
Magnetic relay (Y2S)
Magnetic relay (E1HC)
Magnetic relay (Y1S)
K5R,K6R,K7R Magnetic relay (M1F)
M1C Motor compressor
M1F
PC
Motor fan
Power circuit
Q1DI
Q1M
Earth leakage breaker (30mA)
Thermo switch (M1F)
Q1RP
R1T
R2T
R3T
RC
S1HP
S1LP
SD
T1A
Phase reverse circuit
Thermistor (air)
Thermistor (coil)
Thermistor (discharge pipe)
Signal receiver circuit
Pressure switch (high)
Pressure switch (low)
Safety devices input
Current transformer
TC Signal transmission circuit
X1M,X2M Terminal strip
Y1E Expansion valve (electronic type)
Y1S
Y2S
CT
4-way valve
Solenoid valve
Current transformer
ON
OFF
2TW26336-1B
1
9
• Split Sky Air • Outdoor Units 28
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
9 Wiring diagram
9 - 1 Wiring diagram
REQ125BW1
Switch box
(Outdoor)
Indoor
Power supply
3N ∼50Hz
400V
Note:
Confirm the method of setting the DIP switch (DS1) by service manual when the unit is shipped by factory all switches are set to be off.
g Field wiring
D : Terminal
F b
L
: Connector
: Protective earth (screw)
: Live
N : Neutral
: Terminal
Colours
BLK: Black/ BLU: Blue/ WHT: White/
RED: Red/ ORG: Orange/ YLW:Yellow
Position of compressor terminal
Wire entrance
A1P
BS1
C1
C2
DS1
E1HC
Printed circuit board
Push button (forced defrost-pump down)
Capacitor (M1F)
Capacitor (M2F)
DIP switch
Crankcase heater
F1U, F2U Fuse (T6.3/250V)
HAP Light emitting diode (service monitor green)
K1M Magnetic contactor (M1C)
K1R
K2R
K3R
K4R
Magnetic relay (K1M)
Magnetic relay (Y2S)
Magnetic relay (E1HC)
Magnetic relay (Y1S)
K5R,K6R,K7R Magnetic relay (M1F)
K8R,K9R,K10R Magnetic relay (M2F)
M1C Motor compressor
M1F, M2F Motor fan
PC Power circuit
Q1D
Q1M
Q2M
Q1RP
R1T
R2T
R3T
RC
S1PH
Earth leakage breaker (30mA)
Thermo switch (M1F)
Thermo switch (M2F)
Phase reverse circuit
Thermistor (air)
Thermistor (coil)
Thermistor (discharge pipe)
Signal receiver circuit
Pressure switch (high)
S1LP
SD
T1A
TC
Pressure switch (low)
Safety devices input
Current transformer
Signal transmission circuit
X1M,X2M Terminal strip
Y1E Expansion valve (electronic type)
Y1S
Y2S
CT
4-way valve
Solenoid valve
Current transformer
ON
OFF
Outdoor
2TW26366-1B
1
9
29 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
9 Wiring diagram
9 - 2 External connection diagram
REQ71 ∼125B
Field wire
Symbol explication
I = Pair
II = Twin
III = Triple
M = Master
S = Slave
1 = Earth leak detector
2 = Fuse
3 = Remote control
4TW26329-7
1
9
30 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
10 Sound data
10 - 1 Sound pressure spectrum
REQ71B - Cooling REQ71B - Heating
3TW26597-1
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ71B in cooling mode
Measuring location
(discharge side)
REQ100B - Cooling
3TW26597-2
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ71B in heating mode
Measuring location
(discharge side)
REQ100B - Heating
1
10
31
3TW26617-1
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ100B in cooling mode
Measuring location
(discharge side)
• Split Sky Air • Outdoor Units
3TW26617-2
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ100B in heating mode
Measuring location
(discharge side)
REQ125B - Cooling
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
10 Sound data
10 - 1 Sound pressure spectrum
REQ125B - Heating
3TW26637-1
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ125B in cooling mode
Measuring location
(discharge side)
3TW26637-2
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ125B in heating mode
Measuring location
(discharge side)
1
10
32 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
10 Sound data
10 - 2 Sound power spectrum
REQ71B - Cooling REQ100B - Cooling
3TW26597-3
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ71B in cooling mode
REQ125B - Cooling
3TW26617-3
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ100B in cooling mode
1
10
33
3TW26637-3
NOTES
Octave band center frequency (Hz)
1 Data is valid at free field condition
2 Data is valid at nominal operation condition
3 dB(A) = A-weighted sound pressure level (A-scale according to IEC)
4 Reference acoustic pressure 0dB = 20μPa
5 Curve for REQ125B in cooling mode
• Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
11 Installation
11 - 1 Installation method
REQ71 ∼ 125B
Oil trap
Indoor unit
Oil trap
Outdoor unit
Gas piping
Liquid piping
NOTE:
Since there is fear of the oil held inside the riser piping flowing back into the compressor when stopped and causing liquid compression phenomenon, or cases of deterioration of oil return, it well be necessary to provide a trap at an appropriate place in the riser gas piping.
A trap is not necessary when the outdoor unit is installed in a higher position than the indoor unit.
4TW25149-8
1
11
• Split Sky Air • Outdoor Units 34
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
11 Installation
11 - 2 Service space
REQ71 ∼ 125B
A. Non stacked installation
B. Stacked installation
1. Obstacles exist in front of the outlet side 2. Obstacles exist in front of the air inlet
Legend
Suction side obstacle
Discharge side obstacle
Left side obstacle
Right side obstacle
Top side obstacle
Obstacle is present
In these cases, close the bottom of the installation frame to prevent discharged air from being bypassed.
In these cases, only 2 units can be installed.
This situation is not allowed.
Figures between ( ) indicate the dimensions only for the
100-125 class models.
1
11
Do not stack more than one unit.
About 100mm is required as the dimension for laying the upper outdoor unit’s drain pipe.
Get the portion A sealed so that air from the outlet does not bypass.
C. Multiple-row installation
1. Installation of one unit per row 2. Installing multiple units (2 units or more) in lateral connection per row
Relation of dimensions of H, A, and L are shown in the table below.
L ≤ H
H < L
L
0 < L ≤ 1/2 H
A
150 (250)
1/2 H < L 200 (300)
Installation impossible
3TW25149-4A
35 • Split Sky Air • Outdoor Units
• Outdoor Units • R-410A • REQ-B8V3B_REQ-B8W1B
12 Operation range
REQ71 ∼125B
Cooling
REQ71BV3
REQ71BW1
Model name
REQ100BV3
REQ100BW1
Heating
REQ125BW1
Indoor temp. (°CWB)
Notes:
- Depending on operation and installation conditions, the indoor unit can change over to freeze-up operation (indoor de-icing).
- To reduce the freeze-up operation (indoor de-icing) frequency, it is recommended to install the outdoor unit in a location not exposed to wind.
Indoor temperature (°CDB)
3TW26593-1
1
12
36 • Split Sky Air • Outdoor Units
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project