User's Guide
Autoranging Multimeter plus IR Thermometer
Extech 450
Patent Pending
Introduction
Congratulations on your purchase of the Extech 450 (part number
EX450) Autoranging Multimeter plus IR Thermometer. This meter measures AC/DC Voltage, AC/DC Current, Resistance, Diode
Test, and Continuity plus Non-Contact IR Temperature. Proper use and care of this meter will provide many years of reliable service.
Safety
WARNING
CAUTION
MAX
1000V
This symbol adjacent to another symbol, terminal or operating device indicates that the operator must refer to an explanation in the
Operating Instructions to avoid personal injury or damage to the meter.
This WARNING symbol indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury.
This CAUTION symbol indicates a potentially hazardous situation, which if not avoided, may result damage to the product.
This symbol advises the user that the terminal(s) so marked must not be connected to a circuit point at which the voltage with respect to earth ground exceeds (in this case)
750 VAC or 1000VDC.
This symbol adjacent to one or more terminals identifies them as being associated with ranges that may, in normal use, be subjected to particularly hazardous voltages. For maximum safety, the meter and its test leads should not be handled when these terminals are energized.
This symbol indicates that a device is protected throughout by double insulation or reinforced insulation.
This symbol indicates there is a potential hazard from a laser light source.
2 EX450V5.0V 10/06
OVERVOLTAGE CATEGORY III
This meter meets the IEC 610-1-95 standard for OVERVOLTAGE
CATEGORY III. Cat III meters are protected against overvoltage transients in fixed installation at the distribution level. Examples include switches in the fixed installation and some equipment for industrial use with permanent connection to the fixed installation.
SAFETY INSTRUCTIONS
This meter has been designed for safe use, but must be operated with caution. The rules listed below must be carefully followed for safe operation.
1. NEVER apply voltage or current to the meter that exceeds the specified maximum:
Input Protection Limits
V DC or V AC mA AC/DC
A AC/DC
1000V DC/750V AC, 200Vrms on
200mV range
200mA 250V fast acting fuse
20A 250V fast acting fuse(30 seconds max every 15 minutes)
250Vrms for 15sec max Resistance, Diode Test,
Continuity
2. USE EXTREME CAUTION when working with high voltages.
3. DO NOT measure voltage if the voltage on the "COM" input jack exceeds 1000V above earth ground.
4. NEVER connect the meter leads across a voltage source while the function switch is in the current, resistance, or diode mode. Doing so can damage the meter.
5. ALWAYS discharge filter capacitors in power supplies and disconnect the power when making resistance or diode tests.
6. ALWAYS turn off the power and disconnect the test leads before opening the cover to replace the fuse or battery.
7. NEVER operate the meter unless the back cover and the battery and fuse covers are in place and fastened securely.
8. NEVER look directly at the laser light source or aim the pointer at an eye.
3 EX450V5.0V 10/06
Controls and Jacks
1. IR Thermometer and laser pointer
2. 2000 count LCD display
6. mA, uA and A input jacks
7. COM input jack
9. MAX hold button (voltage and current)
10. BACKLIGHT button
11. Laser pointer button
12. Protective holster
Note: Tilt stand and battery compartment are on rear of unit.
Symbols and Annunciators
•))) Continuity
Diode test
Laser pointer
Battery status
Test lead connection error m milli A
3
F
Amps
Farads (capacitance)
Ω
Ohms
V Volts
AUTO Autoranging
HOLD Display hold ºF Degrees Fahrenheit
4 EX450V5.0V 10/06
Specifications
Function Range Resolution
DC
Voltage
Accuracy
200mV 0.1mV ±(0.5% reading + 2 digits)
2V 0.001V
20V 0.01V
±(0.8% reading + 2 digits)
AC
Voltage
200V 0.1V
1000V 1V ±(1.0% reading + 3 digits)
50 to 400Hz 400Hz to 1kHz
±(2.5% reading
+ 8 digits)
750V 1V
±(1.0% reading
+ 4 digits)
20V 0.01V ±(1.5% reading
200V 0.1V
+ 4 digits)
±(2.0% reading
+ 6 digits)
±(3.0% reading
+ 8 digits)
±(3.5% reading
+ 8 digits)
DC
Current
200
µA 0.1µA
2000
µA 1µA
20mA 0.01mA
±(1.5% reading + 3 digits)
200mA 0.1mA
AC
Current
20A 0.01A
200
µA 0.1µA
50 to 400Hz 400Hz to 1KHz
2000
µA 1µA
20mA 0.01mA
±(1.8% reading
+ 8 digits)
±(3.0% reading
+ 7 digits)
200mA 0.1mA
20A 0.01A
±(3.0% reading
+ 8 digits)
±(3.5% reading
+ 10 digits)
NOTE: Accuracy is stated at 65 o
F to 83 than 75% RH. o
F (18 o
C to 28 o
C) and less
5 EX450V5.0V 10/06
Function Range Resolution
Resistance
200
Ω 0.1Ω
Accuracy
±(0.8% reading + 4 digits)
2k
Ω 0.001kΩ ±(0.8% reading + 2 digits)
Temp
(IR)
20k
Ω 0.01kΩ
200k
Ω 0.1kΩ
2M
Ω 0.001MΩ
20M
Ω 0.01MΩ
-58 to 518
°F 1°F
-50 to270
°C 1°C
±(1.0% reading + 2 digits)
±(3.0% reading + 5 digits)
±2.0% reading or ±2°C, ± 4 °F
NOTE: Accuracy specifications consist of two elements:
• (% reading) – This is the accuracy of the measurement circuit.
• (+ digits) – This is the accuracy of the analog to digital converter.
Diode Test
Continuity Check
IR Spectral response
IR Emissivity
IR distance ratio
Test current of 0.3mA maximum, open circuit voltage 1.5V DC typical
Audible signal will sound if the resistance is less than 150
Ω
(approx.), test current <0.7mA
6 to 16µm
0.95 fixed
8:1
Input Impedance >7.5MΩ (VDC & VAC)
AC Response
Average responding
ACV Bandwidth
50Hz to 1kHz
Display
Overrange indication
Auto Power Off
Polarity
Measurement Rate
Low Battery Indication
2000 count backlit liquid crystal
“OL” is displayed
15 minutes (approximately)
Automatic (no indication for positive); Minus (-) sign for negative
2 times per second, nominal
“ ” is displayed if battery voltage drops below operating voltage
6 EX450V5.0V 10/06
Battery One 9 volt (NEDA 1604) battery
Fuses
Operating Temperature 41ºF to 104ºF (5ºC to 40ºC)
Storage Temperature -4 o
F to 140 o
F (-20 o
C to 60 o
C)
Operating Humidity
mA, µA ranges; 0.2A/250V fast blow
A range; 20A/250V ceramic fast blow
Max 80% up to 87ºF (31ºC) decreasing linearly to 50% at 104ºF(40ºC)
Storage Humidity
Operating Altitude
Weight
Size
Safety
<80%
7000ft. (2000meters) maximum.
0.753lb (342g) (includes holster).
7.36” x 3.2” x 2.0” (187 x 81 x 50mm)
(includes holster)
For indoor use and in accordance with the requirements for double insulation to
IEC1010-1 (1995): EN61010-1 (1995)
Overvoltage Category III 600V and
Category II 1000V, Pollution Degree 2.
7 EX450V5.0V 10/06
Operating Instructions
WARNING: Risk of electrocution. High-voltage circuits, both AC and DC, are very dangerous and should be measured with great care.
1. ALWAYS turn the function switch to the OFF position when the meter is not in use.
2. If “OL” appears in the display during a measurement, the value exceeds the range you have selected. Change to a higher range.
NOTE: On some low AC and DC voltage ranges, with the test leads not connected to a device, the display may show a random, changing reading. This is normal and is caused by the high-input sensitivity. The reading will stabilize and give a proper measurement when connected to a circuit.
DC VOLTAGE MEASUREMENTS
CAUTION: Do not measure DC voltages if a motor on the circuit is being switched ON or OFF. Large voltage surges may occur that can damage the meter.
1. Set the function switch to the green
V position.
2. Press the SELECT button to indicate “DC” on the display.
3. Insert the black test lead banana plug into the negative COM jack.
Insert the red test lead banana plug into the positive V jack.
4. Touch the black test probe tip to the negative side of the circuit.
Touch the red test probe tip to the positive side of the circuit.
5. Read the voltage in the display.
8 EX450V5.0V 10/06
AC VOLTAGE MEASUREMENTS
WARNING: Risk of Electrocution. The probe tips may not be long enough to contact the live parts inside some 240V outlets for appliances because the contacts are recessed deep in the outlets. As a result, the reading may show 0 volts when the outlet actually has voltage on it. Make sure the probe tips are touching the metal contacts inside the outlet before assuming that no voltage is present.
CAUTION: Do not measure AC voltages if a motor on the circuit is being switched ON or OFF. Large voltage surges may occur that can damage the meter.
1. Set the function switch to the green
V position.
2. Press the SELECT button to indicate “AC” on the display.
3. Insert the black test lead banana plug into the negative COM jack.
Insert red test lead banana plug into the positive V jack.
4. Touch the black test probe tip to the neutral side of the circuit.
Touch the red test probe tip to the
“hot” side of the circuit.
5. Read the voltage in the display.
9 EX450V5.0V 10/06
DC CURRENT MEASUREMENTS
CAUTION: Do not make current measurements on the 20A scale for longer than 30 seconds. Exceeding 30 seconds may cause damage to the meter and/or the test leads.
1. Insert the black test lead banana plug into the negative
COM jack.
2. For current measurements up to 2000µA DC, set the function switch to the yellow
µA position and insert the red test lead banana plug into the
µA/mA jack.
3. For current measurements up to 200mA DC, set the function switch to the yellow mA position and insert the red test lead banana plug into the
µA/mA jack.
4. For current measurements up to 20A DC, set the function switch to the yellow 20A range and insert the red test lead banana plug into the 20A jack.
5. Press the SELECT button to indicate “DC” on the display.
6. Remove power from the circuit under test, then open up the circuit at the point where you wish to measure current.
7. Touch the black test probe tip to the negative side of the circuit.
Touch the red test probe tip to the positive side of the circuit.
8. Apply power to the circuit.
9. Read the current in the display.
Note: When current measurements exceed 10 Amps the meter will produce an audible warning tone which indicates that the measurement time should be limited to 30 seconds or less.
10 EX450V5.0V 10/06
AC CURRENT MEASUREMENTS
CAUTION: Do not make current measurements on the 20A scale for longer than 30 seconds. Exceeding 30 seconds may cause damage to the meter and/or the test leads.
1. Insert the black test lead banana plug into the negative COM jack.
2. For current measurements up to 2000µA AC, set the function switch to the yellow µA position and insert the red test lead banana plug into the
µA/mA jack
3. For current measurements up to 200mA AC, set the function switch to the yellow mA position and insert the red test lead banana plug into the
µA/mA jack.
4. For current measurements up to 20A AC, set the function switch to the yellow 20A range and insert the red test lead banana plug into the 20A jack.
5. Press the SELECT button to indicate “AC” on the display.
6. Remove power from the circuit under test, then open up the circuit at the point where you wish to measure current.
7. Touch the black test probe tip to the neutral side of the circuit.
Touch the red test probe tip to the “hot” side of the circuit.
8. Apply power to the circuit.
9. Read the current in the display.
Note: When current measurements exceed 10 Amps the meter will produce an audible warning tone which indicates that the measurement time should be limited to 30 seconds or less.
11 EX450V5.0V 10/06
RESISTANCE MEASUREMENTS
WARNING: To avoid electric shock, disconnect power to the unit under test and discharge all capacitors before taking any resistance measurements. Remove the batteries and unplug the line cords.
1. Set the function switch to the green
Ω position.
2. Insert the black test lead banana plug into the negative COM jack.
Insert the red test lead banana plug into the positive
Ω jack.
3. Press the SELECT button to indicate
Ω on the display.
4. Touch the test probe tips across the circuit or part under test. It is best to disconnect one side of the part under test so the rest of the circuit will not interfere with the resistance reading.
5. Read the resistance in the display.
12 EX450V5.0V 10/06
CONTINUITY CHECK
WARNING: To avoid electric shock, never measure continuity on circuits or wires that have voltage on them.
1. Set the function switch to the green Ω position.
2. Insert the black lead banana plug into the negative COM jack
Insert the red test lead banana plug into the positive
Ω jack.
3. Press the SELECT button to indicate
on the display
4. Touch the test probe tips to the circuit or wire you wish to check.
5. If the resistance is less than approximately 150
Ω, the audible signal will sound. If the circuit is open, the display will indicate “OL”.
DIODE TEST
1. Set the function switch to the green Ω position.
2. Insert the black test lead banana plug into the negative COM jack and the red test lead banana plug into the positive V jack.
3. Press the SELECT button to indicate
on the display.
4. Touch the test probes to the diode under test. Forward voltage will typically indicate
0.400 to 0.700V. Reverse voltage will indicate “OL”.
Shorted devices will indicate near 0V and an open device will indicate “OL” in both polarities.
13 EX450V5.0V 10/06
NON-CONTACT TEMPERATURE MEASUREMENTS
1. Set the function switch to the red IR Temp position.
2. Press the SELECT button to select ºF or ºC
3. Point the meter at the surface to be measured.
4. If needed, press the IR Laser Pointer button to locate the exact spot being measured.
5. The area of the surface to be measured must be larger than the spot size as determined by the distance to spot size specification.
6. Read the temperature in the display.
Diameter of Spot
(10cm)
(2.5cm) (5cm)
(20cm)
(40cm)
(80cm)
Distance to Object
WARNING: Do not directly view or direct the laser pointer
at an eye. Low power visible lasers do not normally present a hazard, but may present some potential for hazard if viewed directly for extended periods of time.
14 EX450V5.0V 10/06
DISPLAY BACKLIGHT
Press and hold the button for >1 second to turn on or off the display backlight function. The backlight will automatically turn off after 30 seconds.
MAX
Press the MAX button to activate the MAX feature in the voltage or current functions. The display will hold the maximum reading and will update only when a reading higher then the currently displayed reading occurs. Press the MAX button again to disable the feature.
HOLD
The hold function freezes the reading in the display. Press the
HOLD key momentarily to activate or to exit the hold function.
AUTO POWER OFF
The auto off feature will turn the meter off after 15 minutes.
LOW BATTERY INDICATION
The icon will appear in the lower left conner of the display when the battery voltage becomes low. Replace the battery when this appears.
WRONG CONNECTION INDICATION
The icon will appear in the upper right conner of the display and the buzzer will sound whenever the positive test lead is inserted into the 20A or uA/mA input jack and a noncurrent (green, black or red) function is selected. If this occurs, turn the meter off and reinsert the test lead into the proper input jack for the function selected.
15 EX450V5.0V 10/06
Maintenance
WARNING: To avoid electric shock, disconnect the test leads from any source of voltage before removing the back cover or the battery or fuse covers.
WARNING: To avoid electric shock, do not operate your meter until the battery and fuse covers are in place and fastened securely.
This MultiMeter is designed to provide years of dependable service, if the following care instructions are performed:
1. KEEP THE METER DRY. If it gets wet, wipe it off.
2. USE AND STORE THE METER IN NORMAL
TEMPERATURES. Temperature extremes can shorten the life of the electronic parts and distort or melt plastic parts.
3. HANDLE THE METER GENTLY AND CAREFULLY. Dropping it can damage the electronic parts or the case.
4. KEEP THE METER CLEAN. Wipe the case occasionally with a damp cloth. DO NOT use chemicals, cleaning solvents, or detergents.
5. USE ONLY FRESH BATTERIES OF THE RECOMMENDED
SIZE AND TYPE. Remove old or weak batteries so they do not leak and damage the unit.
6. IF THE METER IS TO BE STORED FOR A LONG PERIOD
OF TIME, the batteries should be removed to prevent damage to the unit.
16 EX450V5.0V 10/06
BATTERY INSTALLATION
WARNING: To avoid electric shock, disconnect the test leads from any source of voltage before removing the battery cover.
1. Turn power off and disconnect the test leads from the meter.
2. Open the rear battery cover by removing two screws (B) using a Phillips head screwdriver.
3. Insert the battery into battery holder, observing the correct polarity.
4. Put the battery cover back in place. Secure with the screw.
WARNING: To avoid electric shock, do not operate the meter until the battery cover is in place and fastened securely.
NOTE: If your meter does not work properly, check the fuses and battery to make sure that they are still good and that they are properly inserted.
17 EX450V5.0V 10/06
REPLACING THE FUSES
WARNING: To avoid electric shock, disconnect the test leads from any source of voltage before removing the fuse cover.
1. Disconnect the test leads from the meter.
2. Remove the protective rubber holster.
3. Remove the battery cover (two “B” screws) and the battery.
4. Remove the four “A” screws securing the rear cover.
5. Lift the center circuit board straight up from the connectors to gain access to the fuse holders.
6. Gently remove the old fuse and install the new fuse into the holder.
7. Always use a fuse of the proper size and value (0.2A/250V fast blow for the 200mA range, 20A/250V fast blow for the 20A range).
8. Align the center board with the connectors and gently press into place.
9. Replace and secure the rear cover, battery and battery cover.
WARNING: To avoid electric shock, do not operate your meter until the fuse cover is in place and fastened securely.
UL LISTED
The UL mark does not indicate that this product has been evaluated for the accuracy of its readings.
18 EX450V5.0V 10/06
Warranty
EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for three years from date of shipment (a six month limited warranty applies on sensors and cables). If it should become necessary to return the instrument for service during or beyond the warranty period, contact the Customer Service Department at
(781) 890-7440 ext. 210 for authorization or visit our website at www.extech.com (click on ‘Contact Extech’ and go to ‘Service Department’ to request an RA number). A Return Authorization (RA) number must be issued before any product is returned to Extech. The sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification.
Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or implied.
Calibration and Repair Services
Extech offers complete repair and calibration services for the products we sell. For periodic calibration, NIST certification or repair of an Extech product, call customer service for details on services available for that product. Extech recommends that calibration be performed on an annual basis to ensure calibration integrity.
Support Hotline (781) 890-7440
Tech support: Ext. 200; Email: [email protected]
Repair/Returns: Ext. 210; Email: [email protected]
Website: www.extech.com
Copyright © 2006 Extech Instruments Corporation.
All rights reserved including the right of reproduction
in whole or in part in any form.
19 EX450V5.0V 10/06
