advertisement
▼
Scroll to page 2
of 3
PRECAUTIONS 5436 W Crenshaw Street Tampa, FL 33634 www.digital-watchdog.com Technical Support: 1-866-446-3595 / 813-888-9555 INSTRUCTION MANUAL ■ Do not open or modify Do not open the case except during maintenance and installation, as it may be dangerous and cause damages. ■ Do not put objects inside the unit Make sure that no metal objects or flammable substances get inside the camera. It could cause fire, short-circuits or damages. B2372TIR ■ Be careful when handling the unit To prevent damage, do not drop the camera or subject it to strong shock or vibration. About manual ■ Install away from electric or magnetic fields Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference. ■ Protect from humidity and dust ■ Protect from high temperature Be careful when installing close to the ceiling , in a kitchen or boiler room, as the temperature may rise to high levels. TROUBLESHOOTING Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center. ■ If no image appears. Is the coaxial cable attached securely? Are the power and voltage normal? Has the iris of the lens inside the camera been adjusted correctly (with the level volume) ? Is there adequate illumination? ■ If the image is unclear Is the lens in focus? Is the lens dirty? Dirt of fingerprints on the lens can adversely affect the images. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available). Is the monitor adjusted correctly? ■ Cleaning Dirt can be removed from the case only by wiping it with a soft cloth moistened with a soft detergent solution. ■ Mounting Surface The mounting surface material must be strong enough to support the camera. WARRANTY INFORMATION Digital Watchdog (referred to as “the Warrantor”) warrants the Camera Series against defects in materials or workmanship as follows: LABOR: For the initial five (5) years from the date of original purchase, if the camera is determined to be defective, the Warrantor will repair or replace the unit, with new or refurbished product at its option, at no charge. PARTS: In addition, the Warrantor will supply replacement parts for the initial five (5) years. To obtain warranty or out of warranty service, please contact a Technical Support Representative at 1-866-446-3595 Monday through Friday from 9:00 AM to 5:00 PM Eastern. A purchase receipt or other proof of the date of the original purchase is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use. This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God. DIMENSION (mm) LIMITS AND EXCLUSIONS There are no express warranties except as listed above. The Warrantor will not be liable for incidental or consequential damages (including, (including without limitation, limitation damage to recording media) resulting from the use of these products, or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from state to state. If the problem is not handled to your satisfaction, then write to the Address above. Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in its sole discretion, are not covered. Costs of such service calls are the responsibility of the purchaser. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAMERA SETTINGS CAMERA SETTINGS ■ Functional control of "REMOTE CONTROL" [OPTION] Omni‐Focus Remote Control Instructions 1. Check the Dip switch (SW4) for camera ID (Default is 0) 2. Point the remote control towards the camera, then press and hold [0] until the Red LED light start flashing. 3. Press and hold the KEY button, until LED turns a solid RED. 4. Press the Plus sign (+) to ZOOM IN, Minus sign (‐) to ZOOM OUT 5. Press the [ENT] button to enter the setup Menu and press [KEY] button to exit. ③ 1.2.4.8 ① ④ ② KEY BUTTON ※ ADJUSTMENT OSD BUTTON 1. Separate opening cap from CAMERA BODY. 2. Camera settimg 3. Assemble opening cap with CAMERA BODY. ① ID NUMBER SWITCH Zoom Focus Control Buttons 1.2.4.8(BCD Code) means ID number and ID contains 10 number from 0 to 9. ID Buttons BUTTON ② SECOND VIDEO OUT CONNECTOR If installer do setting with protable monitor, this connector should be connected. Note : B2372TIR has no Alarm function. ③ ADJUSTING LEVEL VOLUME CCW (Low) Closes the lens iris, making the entire image darker CW(High) Opens the lens iris, making the entire image drighter CONNECTION ④ OSD MENU CONTROL SETUP FUNCTION SUMMARY LENS MANUAL.DC - DC : bright level SHUTTER FIXED,MANUAL,FLK - MANUAL : Manual shutter adjust. BLC ON,OFF AGC ON,OFF WHITE BAL ATW,AWB,FIXED,MANUAL ADJUST CONTRAST,SHARPNESS CB_GAIN,CR_GAIN - BLC AREA - BLC RATIO - AGC GAIN: Min~ Max - MANUAL : RED,BLUE - FIXED : MODE 1,2,3,4 - CONTRAST adjust. - SHARPNESS adjust. - CB_GAIN adjust. - CR_GAIN adjust. FUNCTION ☜ CAMERA ID ON,OFF MIRROR ON,OFF DAY NIGHT AUTO,B/W,COLOR CAUTION : Check for polarity when using a DC 12V power supply. - CAMERA ID 2'nd video cable - POSITION - Mirror image on/off CAMERA SETING ANGLE - AUTO: DELAY START LEVEL END LEVEL - AREA MOTION ON,OFF ① - MOTION TH - MOTION TRACE ON/OFF PRIVACY ON.OFF GAMMA USER, 0.05~1.0 LANGUAGE RESET EXIT - AREA SEL - AREA STATE - GAMMA set. ENGLISH,Korean,Chinese1,Chinese - Language set. Japanes e 2,日本語 YES,NO - Returns to the level - Save out ② ※ ATTENTION 1. Do not rotate ① more than 360˚. 2. Do not twist ② many times unnecessarily. Specifications Model B2372TIR Ture Day/Night Digital Bullet IR Camera Mount 3D Bracket Device 1/3" Super HAD II CCD Image Pixels-Total 811(H) x 508(V) Pixels-Effective 768(H) x 494(V) System 525 line, 2:1Interlace Scanning Horizontal Frequency Internal Mode15,734Hz Vertical Frequency Internal Mode 59.94Hz 0.0 Lux Min. Scene Illumination IR-LED on IR 70 feet range IR DISTANCE BLC ON/OFF (Area Setting) OSD Controls AGC ON/OFF (Gain Adjust) AWB ATW / AWB / Fixed / Manual Mirror ON/OFF Motion Detection ON/OFF (Area / Sensitivity / Trace ON/OFF) Privacy Zone 4 Programmable Zone / Size Focal Length Pan-Focus Lens [2.9 ~ 8.5mm (3x Optical)] Lens Horizontal 540 TV Lines [at TDN (B/W) :570 TV Lines] Resolution VBS 1.0Vp-p VBS 1.0Vp-p(75 Load) Video Output S/N Ratio 48dB S/N Ratio Environmental Condition Operating Temperature -10℃ ~ +55℃(14℉ ~ 131℉) Humidity Less than 90% Power Requirement 12VDC / 24VAC Power 12VDC: 258mA (LED OFF), 418mA (LED ON) 1A (Heater ON) Power Consumption 24VAC: 225mA (LED OFF), 408mA (LED ON), 500mA (Heater Dimensions(H x L) 75.5 x 231.5mm Physical Specification Nema Type IP66 Camera TYPE Certifications Color/BW Weight CE, FCC, RoHS 2.3 lbs Certified
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project