V1362DIR / V1363TIR / V1382TIR

Vandal Dome Camera

User Manual

ABOUT MANUAL

Be sure to keep it handy for future reference.

06212011

PRECAUTIONS

̰GG

Do not open or modify.

̰GG

Do not open the case except during maintenance and installation,

for it may be dangerous and can cause damages.

̰

G Do not put objects into the unit.

̰GGGG

Keep metal objects and flammable substances from entering the camera. It can cause fire, short- circuits, or other damages.

̰GGG

Be careful when handling the unit.

̰

To prevent damages, do not drop the camera or subject it to shock or vibration.

̰

Do not install near electric or magnetic fields.

̰

Protect from humidity and dust.

̰

Protect from high temperature.

̰

Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high levels.

̰

Cleaning

GGGGG

To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.

̰

Mounting Surface

GGGGG

The material of the mounting surface must be strong enough to support the camera.

2

TROUBSHOOTING

Before sending your camera out for repair, check the items below.

If the problem persists after checking these items, contact your service center.

̰

No Video

Is the coaxial cable attached securely?

Is there adequate illumination?

̰

Out-of-Focus Video

Is the lens in focus?

Is the lens dirty?

(commercially available) and a soft cloth or lens cleaning paper.

WARNING : TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

3

D

IMENSIONS IN MILLIMETERS*

109.6

103.1

41.3

6.5

ø145

91.0

85.0

91.0

85.0

ø4.5

VIDEO (YELLOW)

BNC JACK

DC 12V or AC24V

RED

BLACK

5mm TWIST SOLDERING

L= 300mm

ø5.0

117.0

125.0

4

I

NSTALLATION*

E

C

F

G

B

3. Detach the Gimbal (C) from the Base (E).

drill the screw holes at the two marked positions. camera unit through the cable hole in the ceiling.

7. Align the screw holes of the camera unit with the holes in the ceiling. Secure the camera to the ceiling with the two screws. camera window, and then fix it to the Base (E).

11. Attach the Upper Case (A) with the Base (E) and tighten the Fixing Screws (D).

A

D

5

C

ONNECTION*

DC12V

DC12V / AC24V

300.0

CAUTION : CHECK FOR POLARITY WHEN USING A DC12V POWER SUPPLY.

6

C

AMERA SETTINGS*

̰G LENS ADJUSTMENT

1. Focus Lever

2. Zoom Lever

1. Set the zoom level to the desired position by moving the Zoom Lever.

2. Set the focus, using the Focus Lever.

7

8

C

AMERA SETTING FOR SIDE OSD CONTROL BOARD*

V1362DIR, V1363TIR, V1382TIR

SW

RIGHT

UP

LEFT

DOWN

CON1

CON2

FUNCTIONAL OF CONTROL BOARD

[1] SW

Functional control of O.S.D(On Screen Display)

[2] CON1

Second Video output connector

[3] CON2

RS-485 connector

R

EMOTE CONTROL*

Menu Access and Control

Zoom Function Control

Key Button

̰G REMOTE CONTROL Instructions setting is 001. NOTE : you must reset the power for the new settings to apply. Once you reset the power, the camera will recognize the new Camera ID. will turn into the standby image. NOTE : The LED

ID Buttons

Motion Alarm

ON / OFF the Remote Controller. After the number has been input, the LED light will turn on, and the remote controller will be ready to use. NOTE : The ID number is 3 digits. to control the zoom of your camera lens and to select the zoom area of alarm function. Select the area where you wish to observe the movement of objects.

Key. Save the zoom range by pressing the TELE (8)

Key. NOTE: If the zoom range is smaller than the alarm standby range, the zoom range setting will not be saved.

NOTE : PRESS

EFAULT IS “001” FOR

GGGGGGGGGG PRESS TO ACCESS THE MENU

NOTE : THE CAMERA ID IS A DIGIT NUMBER.

9

M

ODULE OSD MENU*

(V1362DIR)

COLOR EXPOSURE

BRIGHTNESS

SHUTTER

BLC

AGC

WB MODE

DAY&NIGHT

D&N MODE

FUNCTION

MIRROR

SHARPNESS

GAMMA

SLC

HME

DRC

SYNC

SYNC

MOTION

ALARM

PRIVACY

MASK 1

MASK 2

MASK 3

MASK 4

COLOR SET

SETUP

CAMERA ID

TITLE EDIT

TITLE RESET

TITLE POSITION

DPC SET

LANGUAGE

PC CONT.

EXIT

EXIT

SAVE & EXIT

FACTORY RESET

10

O

SD MENU*

(V1362DIR)

EXPOSURE

BRIGHTNESS

SHUTTER

BLC

AGC

EXIT JUMP

COLOR

WB MODE

R-Y GAIN

B-Y GAIN

DAY & NIGHT

MANUAL (ELC LEVEL : 0 ~ 100) / DC (DC LEVEL : 0 ~ 31)

1/60, 1/100FLC, 1/120 ~ 1/100000

OFF / ON

BLC (Back Light Compensation)

OFF / 12dB ~ 36dB

AGC (Auto Gain Control)

EXIT / SAVE&EXIT / FACTORY SET

AWC / ATW / MANUAL / PUSHLOCK (AWC is recommended.)

0 ~ 255

0 ~ 255

Day & Night Mode

AUTO / COLOR / BW

COLOR --> BW: Switching from COLOR to BW; If the number is higher, the camera will only

BW --> COLOR: switch during a super low light condition.

S w i t c h i n g f r o m B W t o C O L O R ; T h i s n u m b e r s h o u l d b e a l w a y s l o w e r t h a n

Read Time:

COLOR --> BW

Time interval to switch from COLOR to BW

COLOR:

BW: BURST (OFF/ON); When the burst is OFF, the picture will have less noise.

EXIT / SAVE&EXIT / FACTORY SET EXIT JUMP

11

FUNCTION

MIRROR

SHARPNESS

GAMMA

OFF/ MIRROR

0 ~ 49

SLC

HME

DIS

USER / 0.45 / 0.6 / 1.00

OFF / ON (0 ~ 50)

SLC (Side Light Compensation)

OFF / ON (0 ~ 55)

HME (Highlight Masking Exposure)

OFF /ON

DIS (Digital Image Stabilizer)

EXIT / SAVE&EXIT / FACTORY SET EXIT JUMP

MOTION (OMNI-Plus Cameras Only)

OFF / ON

MOTION

EXIT JUMP

SET WINDOW

ALL SET (Set the Entire Screen)

ALL CLEAR (Clear the Entire Screen)

SENSITIVITY (0 ~ 55)

SHOW INDICATOR (OFF / ICON / TRACE)

DELAY OUT(1 ~ 15)

Motion Alarm Zoom-In Delay

EXIT / SAVE&EXIT / FACTORY SET

12

PRIVACY

MASK 1

MASK 2

MASK 3

MASK 4

COLOR SET

EXIT JUMP

SYNC

SYNC MODE

V-PHASE

EXIT JUMP

SETUP

CAMERA ID

TITLE EDIT

TITLE RESET

TITLE POS.

DPC

LANGUAGE

PC CONT.

EXIT JUMP

EXIT

EXIT

SAVE&EXIT

FACTORY SET

OFF / ON

OFF / ON

OFF / ON

OFF / ON

BLACK / GRAY / COLOR 1~ 6

EXIT / SAVE&EXIT / FACTORY SET

INTERNAL / AUTO

0 ~ 199

EXIT / SAVE&EXIT / FACTORY SET

0 ~ 255

OFF / AUTO

DPC ( Dead Pixel Cancellation)

English / Chinese

OFF / ON

EXIT / SAVE&EXIT / FACTORY SET

Exit the menu

Exit the menu and save the setting

Reset the menu setting to factory default

13

M

ODULE OSD MENU*

(V1363TIR)

COLOR EXPOSURE

BRIGHTNESS

SHUTTER

BLC / HME

AGC

STARLIGHT

NIGHT-UP

WB MODE

R-Y GAIN

B-Y GAIN

DAY&NIGHT

D&N MODE

C_SUP

A_SUP

FUNCTION

MIRROR

SHARPNESS

GAMMA

FREEZE

NEGATIVE

D-ZOOM

3D DNR

DRC

SYNC

SYNC

MOTION

MOTION

SETUP

TITLE EDIT

PC CONTROL

LANGUAGE

MONITOR

OSD COLOR

OMNI LENS

PRIVACY

PRIVACY

EXIT

EXIT

SAVE & EXIT

FACTORY RESET

14

O

SD MENU*

(V1363TIR)

EXPOSURE

BRIGHTNESS

SHUTTER

BLC/HME

AGC

STARLIGHT

NIGHT-UP

EXIT JUMP

COLOR

WB MODE

R-Y GAIN

B-Y GAIN

EXIT JUMP

DAY & NIGHT

Day & Night Mode

C-SUP

A-SUP

EXIT JUMP

0 ~ 100

1/60, FLK, 1/250 ~ 1/100000

OFF / BLC / HME

HIGH / MIDDLE / LOW / OFF

AGC (Auto Gain Control)

AUTO (x2 ~ x256) / OFF

NORMAL / HIGH

EXIT / SAVE & EXIT / FACTORY SET

AWC / AWT / PUSH LOCK / MANUAL / INDOOR / OUTDOOR

0 ~ 100

0 ~ 100

EXIT / SAVE & EXIT / FACTORY SET

AUTO: READ TIME(3~63) / S-LEVEL(0~100) / E-LEVEL(0~100)

COLOR --> BW: Switching from COLOR to BW; If the number is higher, the camera will only switch during a super low light condition

BW --> COLOR: Switching from BW to COLOR; This number should be always lower than

COLOR --> BW.

Read Time: Time interval to switch from COLOR to BW.

COLOR

B&W Mode: BURST (OFF / ON); There is less noise when the BURST is OFF.

SMART IR (OFF / ON)

Color Suppression: Color will be reduced at low illumination, if the C-SUP Level is set higher. 0 ~ 63

Aperture Suppression: The sharpness of the edges will be reduced at low illumination, if

A-SUP level is set higher. 0 ~ 15

EXIT / SAVE & EXIT / FACTORY SET

15

FUNCTION

MIRROR

SHARPNESS

OFF / MIRROR / V-FLIP / ROTATE

0 ~ 31

GAMMA

FREEZE

0.05 ~ 1.00 / USER

OFF / ON

OFF / ON NEGATIVE

D-ZOOM

3D-DNR

DRC

OFF / ON (x1.0 ~ x32 PTZ)

ON (0~100) / OFF

3D Digital Noise Reduction

OFF / INDOOR / OUTDOOR

Dynamic Range Compressor

EXIT / SAVE & EXIT / FACTORY SET EXIT JUMP

MOTION (OMNI-Plus Cameras Only)

OFF

MOTION

ON

AREA SELECT (AREA 1~4)

AREA SET (POSITION / SIZE)

SENSITIVITY (0~40)

MOTION TRACE (OFF / ON)

MOTION VIEW (OFF / ON)

RETURN

EXIT JUMP

PRIVACY

EXIT / SAVE & EXIT / FACTORY SET

PRIVACY

EXIT JUMP

OFF

ON

AREA SELECT (1~8)

AREA SET (POSITION / SIZE)

COLOR (0~15)

RETURN

EXIT / SAVE & EXIT / FACTORY SET

16

SYNC

SYNC

EXIT JUMP

SETUP

TITLE EDIT

PC CONTROL

(RS485 Control)

LANGUAGE

MONITOR

OSD COLOR

OMNI LENS

DEFECT

EXIT JUMP

EXIT

EXIT

SAVE & EXIT

FACTORY SET

INTERNAL / LINE

EXIT / SAVE & EXIT / FACTORY SET

OFF / ON

CAM ID / ID DISPLAY (OFF/ON) / BAUDRATE (2400 / 4800 / 9600)

The protocol is PELCO-D.

ENG / KOR / JPN / CHN1 / CHN2 / RUS / FRAN / SPAN / ITAL

CRT / LCD

Select LCD only if the camera is directly connected to the LCD monitor.

0 ~ 15

OFF (OMNI-Plus Cameras Only)

ON

ALARM / READ TIME / ALARM ZOOM / STAND BY / RETURN

WHITE DEFECT CANCEL MODE

EXIT / SAVE & EXIT / FACTORY SET

17

M

ODULE OSD MENU*

(V1382TIR)

COLOR EXPOSURE

BRIGHTNESS

SHUTTER

BLC

AGC

MAX_DR

STARLIGHT

WB MODE

R-Y GAIN

B-Y GAIN

DAY&NIGHT

D&N MODE

C_SUP

A_SUP

FUNCTION

MIRROR

SHARPNESS

GAMMA

FREEZE

NEGATIVE

3D DNR

D-ZOOM

SLC

HME

DIS

SYNC

SYNC

MOTION

MOTION

SETUP

CAMERA ID

TITLE

DPC

MONITOR

LANGUAGE

BAUDRATE

OMNI LENS

PRIVACY

MASK 1

MASK 2

MASK 3

MASK 4

MASK 5

MASK 6

EXIT

EXIT

SAVE & EXIT

FACTORY RESET

18

O

SD MENU*

(V1382TIR)

EXPOSURE

BRIGHTNESS

SHUTTER

BLC

AGC

MAX_DR

STARLIGHT

EXIT JUMP

COLOR

WB MODE

R-Y GAIN

B-Y GAIN

EXIT JUMP

DAY & NIGHT

Day & Night Mode

C-SUP

A-SUP

EXIT JUMP

0 ~ 99

1/60, 1/100FLC, 1/120~1/100000

OFF / ON

BLC (Back Light Compensation)

HIGH / MIDDLE / LOW / OFF

AGC (Auto Gain Control)

OFF / ON (0~20) (Electronic Wide Dynamic Range)

AUTO (x2 ~ x256) / OFF (x32 is recommended for low light application.)

EXIT / SAVE & EXIT / FACTORY SET

AWC / ATW / MANUAL / PUSHLOCK (AWC is recommended.)

0 ~ 255

0 ~ 255

EXIT / SAVE & EXIT / FACTORY SET

AUTO / COLOR / BW / EX-CONT

COLOR --> BW: Switching from COLOR to BW; If the number is higher, the camera will only switch during a super low light condition.

BW --> COLOR: Switching from BW to COLOR; This number should be always lower than

Read Time:

COLOR --> BW.

Time interval to switch from COLOR to BW.

COLOR

BW: BURST (OFF/ON); When the BURST is OFF, the picture will have less noise.

Color Suppression: Color will be reduced at low illumination, if the C_SUP Level is higher /

0 ~ 100. (Not available when 3D-DNR is ON.)

Aperture Suppression: Edge sharpness will be reduced at low illumination, if A_SUP Level is higher / 0 ~ 100. (Not available when 3D-DNR is ON.)

EXIT / SAVE & EXIT / FACTORY SET

19

FUNCTION

MIRROR

SHARPNESS

GAMMA

FREEZE

NEGATIVE

3D-DNR

D-ZOOM

SLC

HME

DIS

EXIT JUMP

EXIT JUMP

OFF/MIRROR/V-FLIP/ROTATE

0 ~ 49

0.05 ~ 1.00 / USER

OFF / ON

OFF/ ON

OFF / LOW / MIDDLE / HIGH

3D DNR (3D Digital Noise Reduction)

OFF / ON(x1.0 ~ x3.0 Digital PTZ)

OFF / ON

SLC (Side Light Compensation)

OFF / ON

HME (Highlight Masking Exposure)

OFF /ON

DIS (Digital Image Stabilizer)

EXIT / SAVE&EXIT / FACTORY SET

MOTION (OMNI-Plus Cameras Only)

OFF / ON

SET WINDOW

ALL SET (Set the Entire Screen)

ALL CLEAR (Clear the Entire Screen)

MOTION

SENSITIVITY (1 ~ 120)

SHOW INDICATOR (OFF / ICON / TRACE)

DELAY OUT (1 ~ 15)

Motion Alarm Zoom-In Delay

EXIT / SAVE&EXIT / FACTORY SET

20

PRIVACY

PRIVACY

EXIT JUMP

SYNC

SYNC MODE

V-PHASE

EXIT JUMP

SETUP

CAMERA ID

TITLE

DPC

MONITOR

LANGUAGE

BAUDRATE

OMNI LENS

EXIT JUMP

EXIT

EXIT

SAVE&EXIT

FACTORY SET

MASK 1 OFF / ON

MASK 2 OFF / ON

MASK 3 OFF / ON

MASK 4 OFF / ON

MASK 5 OFF / ON

MASK 6 OFF / ON

EXIT / SAVE&EXIT / FACTORY SET

INTERNAL / AUTO

0 ~ 199

EXIT / SAVE & EXIT / FACTORY SET

0 ~ 254

OFF / ON

OFF / AUTO

DPC (Dead Pixels Cancellation)

CRT / LCD (Select LCD only if the camera is directly connected to LCD monitor.)

English / Chinese

2400 / 4800 / 9600 / 14400 / 19200 / 38400

The protocol is

OFF / 1 ~ 10 (OMNI-Plus Cameras Only)

EXIT / SAVE & EXIT / FACTORY SET

Exit the menu

Exit the menu and save the setting

Reset the menu setting to factory default

21

S

PECIFICATIONS*

Model

Camera TYPE Color/BW

Image

Mount

Device

Size

Pixels-Total

Scanning

Min. Scene Illumination

Functions

Lens

Resolution

Video Output

S/N Ratio

OSD

Environmental Conditions

Power

System

Horizontal Frequency Internal Mode

Vertical Frequency Internal Mode

IR-LED On

BLC

AGC

AWB

Mirror

Motion Detection

Privacy Zone

Focal Length

Horizontal

VBS 1.0Vp-p

S/N Ratio

OSD

Operating Temperature

Humidity

Power Requirement

Power Consumption

Dimensions(φ x H)

IP66 IP Rating

V1362DIR

Vandal Dome Camera

Surface

Super HAD II CCD

1/3"

811(H) X 508(V)

768(H) X 494(V)

525 line, 2:1 Interlace

15,734Hz

59.94Hz

0.0 Lux

ON / OFF (Area Setting)

ON / OFF (Gain Adjust)

ATW / AWC / MANUAL / PUSHLOCK

ON / OFF

ON / OFF

4 Programmable Zone / Size

3.3 ~ 12mm Varifocal Auto Iris Lens

540 TV Lines

VBS 1.0Vp-p(75 Load)

50dB

YES

-10 o

C ~ 55 o

C (14 o

F ~ 131 o

F)

Less than 90%

12VDC / 24VAC

12VDC: 1.96W, 163.3mA / 24VAC: 2.2W, 91.7mA

12VDC: 4.4W, 366.7mA / 24VAC: 3.0W, 125mA (LED ON)

109.6 X 145mm, 4.31 X 5.71in

22

S

PECIFICATIONS*

Model

Camera TYPE Color/BW

Image

Mount

Device

Size

Pixels-Total

Scanning

Min. Scene Illumination

Functions

Lens

Resolution

Video Output

S/N Ratio

OSD

Environmental Conditions

Power

System

Horizontal Frequency Internal Mode

Horizontal Frequency Line-Lock Mode

Vertical Frequency Internal Mode

Vertical Frequency Line-Lock Mode

IR-LED On

STAR-LIGHT

3D-DNR

AGC

AWB

Motion Detection

Privacy Zone

Focal Length

Horizontal

VBS 1.0Vp-p

S/N Ratio

OSD

Operating Temperature

Humidity

Power Requirement

Power Consumption

Dimensions(φ x H)

IP66 IP Rating

23

V1363TIR

Vandal Dome Camera

Surface

Super HAD II CCD

1/3"

811(H) X 508(V)

768(H) X 494(V)

525 line, 2:1 Interlace

15.734Hz

15.750Hz

59.94Hz

60Hz

0.0 Lux

OFF / AUTO (x2 ~ x256)

OFF / ON

OFF / LOW / MIDDLE / HIGH

ATW / AWC / INDOOR / OUTDOOR / MANUAL / PUSHLOCK

OFF / ON (Area / Sensitivity)

8 Programmable Zone / Size

3.3 ~ 12mm Varifocal Auto Iris Lens

560TV Lines

VBS 1.0Vp-p (75 Load)

52dB

YES

-10 o C ~ 55 o C (14 o F ~ 131 o F)

Less than 90%

12VDC / 24VAC

12VDC: 1.96W, 163.3mA / 24VAC: 2.2W, 91.7mA

12VDC: 4.4W, 366.7mA / 24VAC: 3.0W, 125mA (LED ON)

109.6 X 145mm, 4.31 X 5.71in

S

PECIFICATIONS*

Model

Camera TYPE Color/BW

Image

Mount

Device

Size

Pixels-Total

Scanning

Min. Scene Illumination

Functions

Lens

Resolution

Video Output

S/N Ratio

OSD

Environmental Conditions

Power

System

Horizontal Frequency Internal Mode

Vertical Frequency Internal Mode

IR-LED On

EWDR

STAR-LIGHT

3D-DNR

DIS

Motion Detection

Privacy Zone

Focal Length

Horizontal

VBS 1.0Vp-p

S/N Ratio

OSD

Operating Temperature

Humidity

Power Requirement

Power Consumption

Dimensions(φ x H)

IP66 IP Rating

V1382TIR

Vandal Dome Camera

Surface

Super HAD II CCD

1/3"

811(H) X 508(V)

768(H) X 494(V)

525 line, 2:1 Interlace

15,734Hz

59.94Hz

0.0 Lux

ON / OFF

OFF / AUTO (x2 ~ x256)

OFF / LOW / MIDDLE / HIGH

ON / OFF

ON / OFF (Area / Sensitivity)

6 Programmable Zone / Size

2.9 ~ 8.5mm OMNI-Focus Lens

580 TV Lines

VBS 1.0Vp-p (75 Load)

50dB

YES

-10 o C ~ 55 o C (14 o F ~ 131 o F)

Less than 90%

12VDC / 24VAC

12VDC: 1.96W, 163.3mA / 24VAC: 2.2W, 91.7mA

12VDC: 4.4W, 366.7mA / 24VAC: 3.0W, 125mA (LED ON)

109.6 X 145mm, 4.31 X 5.71in

24

W

ARRANTY INFORMATION*

Digital Watchdog (referred to as “the Warrantor”) warrants the Camera Series against defects in materials or workmanship as follows.

LABOR : if the camera is determined to be defective, the Warrantor will repair or replace the unit, with new or refurbished product at its option, at no charge.

PARTS : In addition, the Warrantor will supply

To obtain warranty or out of warranty service, please contact a Technical Support Representative at

1-866-446-3595 Monday through Friday from 8:30AM to 8:00PM EST.

A purchase receipt or other proof of the original purchase date is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use.

This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God.

25

L

IMITS AND EXCLUSIONS*

There are no express warranties except as listed above.

The Warrantor will not be liable for incidental or consequential damages, including without limitation or damage to recording media, resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the are limited to the applicable warranty period set forth above.

Some States do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the exclusions or limitations listed above may not may also have other rights that vary from state to state.

If the problem is not handled to your satisfaction, then write to the Address listed on the next page.

Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in its sole discretion, are not covered. Costs of such service calls are the responsibility of the purchaser.

26

5436 W Crenshaw St. Tampa, FL 33634

Tel: 866-446-3595 / 813-888-9555

Fax: 813-888-9262 www.Digital-Watchdog.com

[email protected]

Technical Support Hours: Monday-Friday

8:30am to 8:00pm EST