Quick Installation Guide

TV-IP212/TV-IP212W

TV-IP312/TV-IP312W

H/W: A1.0R

English ...................................................................................................... 1

1. Before You Start ................................................................................

2. Hardware Installation ........................................................................

3. Configure the Internet Camera Server ...........

....................................

1

2

3

Troubleshooting ........................................................................................

7

Version 02.17.2009

1. Before You Start

Package Contents

TV-IP312W

( TV-IP212W/TV-IP312W only)

System Requirements

Application

Wireless 2-Way Audio

Internet Camera Server

(TV-IP212W)

2-Way Audio

Internet Camera Server

(TV-IP212)

54Mbps Wireless 10/100Mbps

Internet

Modem

300Mbps Wireless N

Gigabit Router

(TEW-633GR)

Wireless 2-Way Audio Day/Night

Internet Camera Server

(TV-IP312W)

2-Way Audio Day/Night

Internet Camera Server

(TV-IP312)

1

English

2. Hardware Installation

1. Attach the Antenna.

(TV-IP212W/TV-IP312W only)

2. Connect a RJ-45 network cable from a Switch/Router to the

Ethernet port of the Internet

Camera server.

3. Connect external speaker to the

Internet Camera Server (optional)

4. Connect the AC Power Adapter to the Internet Camera Server and then to a power outlet.

5. Connect USB flash drive to the

Internet Camera Server (optional)

(TV-IP212W/TV-IP312W only).

6. Verify the Power and Link LEDs are on.

2

English

3. Configure the Internet Camera Server

Note: It is recommended that you configure the Internet Camera Server from a wired computer. Since the Internet Camera's default IP address is

192.168.10.30, make sure no other network devices are assigned an IP address of 192.168.10.30.

1. Insert the Utility CD-ROM into your

CD-ROM drive and then click IP

Setup.

2. Follow the IPSetup Setup Wizard instructions and then click Next.

3. Click Close.

4. Go to Start -> Programs ->

TRENDnet -> IPSetup and click

IPSetup.

3

English

5. Select the camera server and click

Change IP.

6. Configure the IP address to be in the same subnet as your network, type in the Administrator ID and

Password and click Change. By default:

ID: admin

Password: admin

7. Click OK and wait 30 seconds.

8. Click OK.

9. Double click the camera server to access the browser configuration.

4

English

10. Enter the User name and

Password, and then click OK. By

default:

User Name: admin

Password: admin

11. Right click and select Install

Active X Control.

12. Click Install.

13. Click Setup, Network and then

click Wireless. Configure your

wireless settings to match your

wireless network's settings and

then click Apply (Enable/Enter

the WEP/WPA key when your

wireless network is encrypted.

Contact your network

administrator for more information). (TV-IP212W/

TV-IP312W only)

5

English

14. Disconnect the RJ-45 cable and

unplug the power to the camera

server. Then plug the power back

in (TV-IP212W/TV-IP312W).

Note: The TV-IP212W/TV-IP312W will not work wirelessly until you disconnect the Ethernet cable from the back of the camera.

15. Verify the Power and Link LEDs

are on.

16. Click Live View.

Your configuration is now complete.

For detailed information regarding the TV-IP212/TV-IP212W/TV-IP312/

TV-IP312W configuration and advanced settings, please refer to the User's

Guide included on the Utility & Driver CD-ROM or TRENDnet's website at www.trendnet.com

Register Your Product

To ensure the highest level of customer service and support, please take a moment to register your product Online at:

www.trendnet.com/register

Thank you for choosing TRENDnet

6

English

Troubleshooting

Q1:

The IPSetup Setup Wizard does not detect my Internet Camera Server. What should I do?

A1:

First, verify that you have followed all the steps in Section 2: Hardware Installation. Second, disable any software firewall programs such as ZoneAlarm or Norton Internet Security. If you are using Windows XP or Windows Vista, disable the built in firewall. Third, click on Search in IPSetup.

Fourth, take a pin or paper clip. Then press on the Reset button on the back on the Internet

Camera Server for 10 seconds, then let go. Fifth, connect the Internet Camera Server directly to your computer. Put a static IP address on your computer in the same subnet as the camera (e.g.

192.168.10.5). Then open up your browser and enter the IP address of the Internet Camera

Server into the address bar. By default, the IP address is 192.168.10.30. Follow steps 9-15 in

Section 3: Configure the Internet Camera Server. Click Setup, click Network and then click

Network to change the IP address. Then click Apply. See instructions below to put a static IP

address on a Windows PC.

1. Go into the Control Panel and double-click the Network Connections icon, and then right-click the Local Area Connection icon and then click Properties.

2. Click Internet Protocol (TCP/IP) and then click Properties. Then click on Use the

following IP address, and make sure you assign your network adapter an IP address in the subnet of 192.168.10.x.

Q2:

The Image is blurry. How can I adjust the focus on the Internet camera?

A2:

You can adjust the Internet Camera’s focus by rotating the lens.

Q3: When I click on Live View the image does not load?

A3:

First, make sure that you are using a browser that supports ActiveX or Java.

Second, make sure that Active X or Java is installed.

Q4: How do I connect the TV-IP212W/TV-IP312W to my wireless router or access point?

A4:

Make sure that you configure the camera to have the same SSID, encryption mode and key (if enabled). Follow the instructions in section 2 to configure the camera with the SSID and encryption key.

Q5: After I successfully configured the TV-IP212W/TV-IP312W to match my wireless network settings, I can not connect to the camera.

A5:

First, verify that the wireless settings match your wireless network settings. Second, verify in the wireless section of the browser configuration that the Enable option is checked.

Third, make sure to disconnect the Ethernet cable from the camera and verify that the LINK

LED is blinking green.

If you still encounter problems or have any questions regarding the TV-IP212/TV-IP212W/

TV-IP312/TV-IP312W, please contact TRENDnet’s Technical Support Department.

7

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received. Including interference that may cause undesired operation.

Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local

Authority or Retailer for recycling advice.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

ADVERTENCIA

En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.

Product Warranty Registration

Please take a moment to register your product online.

Go to TRENDnet’s website at http://www.trendnet.com/register

20675 Manhattan Place

Torrance, CA 90501

USA

Copyright ©2009. All Rights Reserved. TRENDnet.