Cobra CPI M1500 Specifications


Add to my manuals
9 Pages

advertisement

Cobra CPI M1500 Specifications | Manualzz

BATTERY SWITCHES

Cole Hersee Battery Isolators

• Without Alternator Field Disconnect

• Installs in the same cutout and hole patterns as competitive switches

• High-impact, black molded cases are impervious to petroleum-based liquids for long life.

Order No

108669

108670

Mfg No

48070

48120

Amp Rating

70

140

List

$80.88

$151.43

8501 & 8502 8503

Perko Battery Selector Switch

For use with two or more batteries and single or dual engine systems.

• Permits selection between batteries for starting and charging, or operation of both batteries in parallel.

• For use in systems under 50 volts.

• Rated for 250 amps continuous, 360 amps intermittent.

• For dual engines where two switches are required.

Order No

700069

Mfg No

8501/DP

Type

Standard

List

$51.88

With Alternator Field Disconnect

Alternator Field Disconnect will interrupt the field current (reducing the possibility of damage) if turned “OFF” with the engine running.

Order No

340984

Mfg No

8503/DP

List

$81.25

Newmar Automatic Power Selector

The Automatic Power Selector (APS) is a solid state device which enables installation of a seamless, redundant power system for critical electronic loads. It selects the higher voltage of two isolated DC power sources and routes power to the load. Should one source falter or fail, the other will automatically supply the load with no transfer delay, operation continues uninterrupted.

Easy installation, two independent power sources are wired to the APS and routed in a single output to the vital load. Rugged, rust-proof anodized aluminum case.

Order No

107711

Mfg No

APS-70

List

$129.60

Perko Battery Selector Switch

• For use with two or more batteries and single or dual engine systems.

• Permits selection between batteries for starting and charging, or operation of both batteries in parallel.

• For use in systems under 50 volts.

• Rated for 450 amps continuous, 1200 amps intermittent

(15 seconds on, 5 minutes off.)

• For dual engines two switches are required.

Order No

340995

Mfg No

8603/DP

List

$216.50

Perko Main Battery Switch

• Ignition protected.

• Surface mounted in red plastic housing with large, black plastic knobs.

• Main disconnect “ON/OFF” switch.

• For use with systems under 50 volts.

• Rated for 250 amps continuous, 360 amps intermittent.

• 5-1/4” diameter x 2-5/8”

Order No

703473

Mfg No

9601DP

List

$64.98

Perko Heavy Duty Battery Disconnect Switch with Alternator Field Disconnect

• For use 6, 12, 24 and 32 volt marine electrical systems.

• Capacity - rated 450 Amps continuous, 1200 Amps intermittent (15 seconds on, 5 minutes off).

• For use in systems under 50 volts.

Dimensions” 5-1/4” square; depth 3-3/8”.

Order No

341006

Mfg No

9703/DP

List

$206.05

Prices and specifications subject to change without notice.

111

BATTERY SWITCHES

Blue Sea Systems e-Series Battery Switch Dual Circuit Plus™

• Allows temporary isolation of house loads from engine circuits during engine cranking to protect sensitive electronics

• Automatically combines battery banks during the charging cycle and isolates under discharge

• 12/24 Volt auto ranging voltage input

• Waterproof · Ignition protected.

• Remote LED indicates various functions

• Supports high-output alternators up to 120 Amperes

• Activates from any charging source - alternators, battery chargers, or solar panels

Continuous Rating: 120 Amperes DC

Intermittent Rating: 210 Amperes DC

Terminal Stud Size 3/8”-16 (accepts M10 ring terminal)

Maximum Cable Size 1/0 AWG

Agency Standards: ISO 8846 / Meets SAE J1171 external ignition protection requirements Width: 3.886”; Height: 3.502” e-Series Battery Switch Single Circuit ON/OFF

• Ignition protected - Safe for installation aboard gasoline powered boats

• Case design allows surface or rear panel mounting

• Meets American Boat and Yacht Council (ABYC) requirements for battery switches.

• Cranking amps max: 900

• Continuous amps max: 350

• Maximum voltage: 48 VDC

Order No

385747

Mfg No

9003e

List

$45.29

Order No

385769

Mfg No

7610

List

$107.99

Blue Sea m-Series (Mini) Battery Switches - Single

Circuit On/Off Switch

• Ignition protected - case design allows surface, front panel,

or rear panel mounting.

• Isolating cover with snap-on sections protects rear contacts

• Inrush Rating: 0.25 sec (10 repeats): 1500 Amps

• DC Cranking Rating: 9.75 sec (10 repeats): 700 Amps

• DC Intermittent Rating: 5 min (UL 1107) 500 Amps

• DC Continuous Rating: (UL 1107) 300 Amps

• DC Maximum Voltage Rating 48 Volts DC

Order No Mfg No

385714

385725

6005

6006

Description

Single Circuit ON/OFF Battery

Switch

Single Circuit ON/OFF Battery

Switch

Type

With Key

With Knob

List

$31.47

$31.47

386105 6011 Dual Circuit Plus™ Battery Switch With Knob $52.44

Blue Sea Systems e-Series Battery Switch Selector

• Make-before-break contact design allows switching between battery banks without power interruption.

• Ignition protected - Safe for installation aboard gasoline powered boats.

• Case design allows surface or rear panel mounting.

• Meets American Boat and Yacht Council requirements for battery switches.

• Cranking amps rating: 900

• Continuous amps rating: 350

• Maximum volts: 48 DC

Order No Mfg No

385736 9001e

Description

4 Position Selector

List

$48.38

386138 9002e

4 Position Selector with Alernator Field

Disconnect

$53.53

Blue Sea Systems HD-Series Battery Switch

• Meets American Boat and Yacht Council (ABYC) requirements for battery switches.

• Ignition protected - safe for installation aboard gasoline powered boats.

• Case design allows surface or rear panel mounting.

• Accepts two 4/0 AWG (95mm²) battery cables.

Order No Mfg No

386116

386127

112

3000

3002

Type

Single Circuit

On/Off

Selector-4

Pos.

Amp Rating List

Blue Sea Systems Shore Power / Generator Selector Switch

• Switches 2 - 120 or 230 Volt AC sources.

• Compact solution when circuit protection is provided elsewhere.

• Allows connecting one of two different AC sources to one circuit.

• Mounts in panels up to 0.16” (4.00mm) thick.

• Heavy duty industrial rated switch.

• Intuitive function - One hand operation.

• UL listed.

• Switches 120 or 230 Volt AC sources.

• 600 Volt AC max.

• Compact solution when circuit protection is provided elsewhere.

• Allows connecting one of several AC sources to one circuit.

• Mounts in panels up to 0.16” (4.00mm) thick.

• Heavy duty industral rated switch.

• Intuitive function - one hand operation.

Intermittent: 900A; Continuous:

600A

$95.02

Order No Mfg No Amp Rating

Intermittent: 700A; Continuous:

500A

$98.94

386330

386341

9009

9019

Prices and specifications subject to change without notice.

30A

65A

Positions

2 + Off

2 + Off

List

$125.00

$350.00

BATTERY SWITCHES

Guest Battery Selector Switch

• Single-pole, triple throw switch permits selection between two batteries, operation of both batteries in parallel, or complete disconnect of both batteries.

• Rated at 230 amps continuous or 345 amps momentary.

• 5-1/2” diameter, 2-5/8” high.

• Three mounting holes on 4-1/8” centers.

• Available with or without alternator field disconnect.

Guest Extra Heavy Duty Diesel On/Off Switch

• A heavy-duty on/off switch with alternator field circuit disconnect for use where high amperage service is required, such as starting diesel engines.

• Rated at 600 amps continuous, 900 amps momentary.

• 5-1/2” square base x 3-1/2” high.

• Four mounting holes on 4-1/2” centers.

Order No Mfg No

Alternator Field

Disconnect

List

Order No

233202

Mfg No

2304A

List

$258.35

233197

233198

2100

2101

Yes

No

$81.73

$81.73

Guest Cruiser Series Universal Mount Switch

• Without Alternator Field Disconnect.

• Installs in the same cutout and hole patterns as competitive switches.

• High-impact, black molded cases are impervious to petroleum-based liquids for long life.

• Diameter: 5-1/2”.

Hella Battery Master Switch

• For interrupting power (prevents theft and short-circuit during absence).

• Removable key.

• Max. load: 100A @ 12V continuous

• 500A @ 24V intermittent.

• Comes with a spare key.

Order No

231135

Mfg No

2843011

List

$27.50

Order No

233169

Mfg No

2111

List

$39.30

Guest Heavy Duty Battery Selector Switch

• Heavy-duty switch is designed for the high amperage of marine service.

• Especially important for the large currents needed to start diesel engines.

• Rated at 360 amps continuous, 600 amps momentary, with alternator field disconnect.

• 5-1/2” square base x 3-1/2” high.

• Four mounting holes on 4-1/2” centers.

Order No

233201

Mfg No

2300A

List

$184.50

Cole Hersee Master Disconnect Switch

• Protect against electrical fires, tampering, theft, etc.

when equipment is unattended.

• Igniton protected.

• Ratings: 175 amps continuous

• 800 amps intermittent

• 15 seconds On, 5 minutes Off

• For 6-36 volt, DC electrical systems

• Silver contacts

• Brass case

• Chrome plated lever

• Brass mounting stem 3/4” diameter, 1-13/32” long.

• Two 3/8” diameter stud terminals

• Fits panels up through 15/16” thick.

Order No Mfg No

108618 M284-01 BP

Prices and specifications subject to change without notice.

List

$77.12

113

MARINE BATTERIES

Exide Nautilus Marine Batteries

Features and benefits

• Heavier cast-on strap - to withstand vibration.

• Stainless steel threaded and SAE posts.

• Calcium/calcium construction. Install it. Forget it.

• Enveloped polypropylene separators - for enhanced vibration resistance.

• Rigid polypropylene case and cover - for longer life in the marine environment.

(1) Limited Options: Instrumentation, Bilge Pump, Blower, Lighting.

(2) Electronic Options: Includes limited options and electronics (Loran, GPS, VHF, Depth and Fish Finder, Auto Pilot, Trim Tabs, Chart Plotter.)

(3) Trolling: Includes limited options and electric trolling motor, live wells.

(4) Full Options: Includes instrumentation, Bilge Pump, Blower, Lighting, all electronic options plus Down Riggers, Windlass, Inverter, Trolling Plates, Full Galley and trolling options.

(5) Full Deep Cycle: Operating full options without engine or generator support, i.e. relying solely on battery for power supply.

Batteries available by store pick-up only. Not UPS Shipable.

Order No Mfg No

120012 EX16CLB

120010 XHDM24

Cranking Amps

300

625

Size

6-15/16” x 4” x 6-1/8”

11-3/8” x 6-3/4” x 10”

List

$74.99

$96.99

120007

120125

120009

120008

120005

120006

XXHDM24

NC24

NC27

NG27

NG4D

NG8D

1000

630

730

670

1400

1725

Application

Kawasaki, Yamaha Jet Skis

O/B and I/B engines up to 300 hp + limited options (1)

O/B and I/B engine up to 750 hp + limited options (1) and electronic options (2)

All engines to 350 hp

All engines from 150 hp to 300 hp with electronics options (2) + trolling (3) or cycling.

All engines from 150 hp to 600 hp with full options (4)

+ trolling (3) + full deep cycle (5)

All diesel engines + all auxiliary items

All diesel engines + all auxiliary items

11-3/8” x 6-3/4” x 10”

11-3/8” x 6-3/4” x 10”

13” x 6-13/16 x 10-1/4”

12” x 6-13/16 x 9-7/16”

20-11/16” x 8-11/16 x 9-7/8”

20-3/4” x 11-1/8” x 10-7/8”

$129.99

$118.99

$134.99

$163.99

$338.99

$406.99

Odyssey Marine Batteries

Phenomenal starting power and massive deep cycle reserve power in one battery!

Some batteries provide enormous cranking power. Others, deep cycle reserve power. The revolutionary ODYSSEY® battery is designed to do both.

How is this possible? The answer begins with flat plates made of 99.99% pure virgin lead - not lead alloy. Pure lead plates can be made thinner, so we can fit more of them in the battery. More ODYSSEY battery plates mean more plate surface area. And that means more power – twice as much as conventional batteries.

Batteries available by store pick-up only. Not UPS Shipable.

Order No

120003

Mfg No

PC1700T

120015 PC1500MST

120004 PC1200T

140389 PC625

Type

Proup 27 Low Profile w ith 3/8” Cable Bolt

Group 24; Most Powerful on Market

Trolling Motor

PWC (Fits most models)

Voltage Cranking Amps Length Width Height

12

12

12

12

875

880

550

265

13.02” 6.62”

10.85” 6.76”

7.87”

6.70”

6.66”

3.90”

6.93”

7.82”

6.80”

6.89”

Warranty

4 Year Free Replacement

4 Year Free Replacement

3 Year Free Replacement

2 Year Free Replacement

List

$455.81

$379.78

$312.27

$159.99

A/C Delco Voyager 12 Volt Batteries

Maintenance-free deep-cycle design allows batteries to provide long streams of power for extended periods.

• Heat-sealed covers provide added strength and rigidity.

• Rope handles with contoured handgrips for comfortable, convenient transport.

• Thermoplastic reinforced plates help increase protection against plate shorting and improve durability.

• Built-in “Green Eye” hydrometer.

• Both positive and negative grids are lead/calcium alloy to maximize corrosion resistance, increase cycle life, and reduce water consumption for battery durability.

Batteries available by store pick-up only. Not UPS Shipable.

Order No

200544

200545

200583

Mfg No

M24MF

M27MF

MM30HMF

Group

24

27

30

Cranking Amps

620

720

900

Dimensions

10.9” L x 6.8” Wx 9” H

12.6” L x 6.8” W x 9” H

30.5” L x 6.7” W x 9.1” H

List

$129.99

$139.99

$149.99

114 Prices and specifications subject to change without notice.

BATTERY BOXES • BATTERY TRAYS

Attwood Battery Holder Trays

Heavy-duty, non-corrosive black plastic. Includes adjustable height crossbar and two retaining bolts. Meets ABYC Standard E-10 and USCG requirements. Patented design.

Install with #10 screws.

Order No

244022

244021

Mfg No

9090-5

41507-1

Group

24

27

Dimensions

10-5/8” x 6-3/4” x 8-3/4”

12-1/8” x 6-3/4” x 8-3/4”

List

$12.10

$13.40

TH Marine Battery Boxes

• Patented quick snap locking lid.

• Combo model has adjustable divider panel.

• Rugged molded poly.

• Resists acid, U/V and chemicals.

Order No

303438

Mfg No

BB-31P

Fits

Groups 27, 29, 31

List

$17.75

Detmar Battery Holder

Keeps batteries securely in place. Prevents loosening of battery cables or spillage of battery acid. Easy to install. Adjustable height crossbar for secure fit. High-strength polypropylene cross piece with stainless steel hold down rods and fasteners.

Order No Mfg No List

233129

233130

10-15-12S

10-15-51S

$16.05

$16.05

Attwood Battery Boxes

All battery boxes meet U.S.C.G. spec. no. 183.420 as an OEM-installed battery hold down system. Polypropylene construction for total acid resistance. Hold-down straps resist 350 lbs. of force. Mounting hardware is included. Vented. Black.

Order No Mfg No

108159 9067-1

244020 9065-1

Group

27

24

Dimensions

16-7/8”x9-5/8”x10-7/8”

14”x9-5/8”x10-5/8”

List

$14.20

$11.90

Odyssey Battery Trays

Order No Mfg No

130505

140406

130504

PC1700-TRAY

PC2150-TRAY

0-01TRAY-PC1

Fits

13.30”L x 8.50”W x 6.75”H

13.30”L x 8.63”W x 8.30”H

8.90”L x 8.50”W x 6.60”H

List

$40.00

$47.00

$40.00

Moeller Roto-Molded Battery Boxes

Seamlessly designed to tackle the elements for long-life battery performance.

• Non-corrosive high-strength polyethylene construction resists chemicals and rust.

• Maintains tough properties with nominal 0.185” wall thickness on roto-molded

(mixed linear-black) boxes.

• Complies to industry requirements and meets Coast Guard regulations (E10).

T-H Marine Battery Holder Trays

Battery holder fits into a limited space and is simple to install. The patented polypropylene hold down strap with positive locking quick disconnect buckle matched with a molded base that mounts with four (4) #10 pan head screws provides not only simple installation but changing or replacing batteries is quick and easy. Meets

NMMA specs.

Order No

302664

302675

730258

Mfg No

BH-24P-DP

BH-27P-DP

BH-31P-DP

Group

24

27

29-31

List

$14.61

$14.61

$14.63

Order

No

Mfg No

259004 042208

259005 042209

259006 042204

259007 042212

Prices and specifications subject to change without notice.

Dimensions Fits

25.00” L x 14.87” W x 11.62” H 8D Battery

Low Profile

24.37” L x 14.50” W x 14.12” H 8D Battery

23.87” L x 12.50” W x 13.5” H

High Profile

4D Battery

17.50” L x 12.87” W x 11.25” H Double Battery Box

List

$118.25

$124.33

$118.65

$113.35

115

BATTERY CHARGERS

Guest Battery Pal™ Model 2602 Battery Charger

Storage/Maintenance Charger

A float charger that will keep your 12 volt batteries factory fresh without overcharging or boiling electrolyte. It supplies only the maintenance charge necessary to preserve battery life. Features an automatic safety shutoff and an LED indicator of proper operation.

Order No Mfg No List

233204 2602 $62.88

Guest Battery Charger Model 2611 Battery Charger Model 2611

A trolling motor charger for the boater who needs 10-12 hour full recovery. Ideal for systems with two 12 volt batteries or a 24 volt configuration. Comes prewired with a

6’ AC cord and two 4’ DC outputs. 10 amps output.

Dimensions: 7-3/4” W x 5-1/8” H x 2-1/16 D.”

Weighs 6 lbs.

Intelligent Charging System Chargers

• The most advanced charging devices available! Fastest Charge with advanced micro-technology for maximum performance!

• The control center is a membrane covered panel, positioned for easy view of all functions and easily accessible to the user selectable buttons.

• Features easy to read LED Indicators of charge status, user selectable buttons to tailor the charge for specific battery types (AGM/Flooded or Gel) per output, and warning indicators to alert you before a serious problem.

• Electronics system is mounted on an anodized aluminum base to provide efficient heat dissipation and decreased weight.

• Circuits are coated in epoxy to protect sensitive electronic components from water or vibration and case is slotted on the sides to provide convection cooling of the anodized aluminum base plate while maintaining an IP65 Water Resistance standard.

Order

No

Mfg No

Total

Amps

Amps per

Out

Input voltage

Output

Voltage

Dimensions

List

Order No

293440

Mfg No

2611A

List

$191.68

293540 16102 12 6/6

12 + 12 or 24

12 VDC

2.4” X

4.9” X

7.0”

$270.20

293551 16202 20 10/10

95-135

VAC,

50/60Hz,

5A

12 VDC

3.0” X

7.1” X

9.9”

$438.23

Guest 20 Amp Dual Trolling Motor Battery Charger

Total Amps: 20 Amps

Number of Outputs: 2

Amps per output: 10/10

Battery System: 2-12V or 1-24V

Output Voltage: 12VDC per output

DC Output: 2 -6’ DC Outputs w/ring terminals

Input Voltage: 100-130VAC/50-60Hz

Input Connection: 6’ AC Cord w/Connect Charge Pro

Dimensions: 9.60” x 7.0” x 2.63”

Weight: 8.0 Lbs.

Remote Indicator Panel

Same Dual Output Remote Indicator used for both 16102 and 16202.

Order No Mfg No List

293538 2620A $344.48

Order No

293562

Mfg No

16002-RI

List

$55.45

Guest Bluewater Cruiser Chargers

Common Features:

• Efficient 3-stage charging with low AC draw.

• Provides and extra boost for engine starting.

• Compact, corrosion- and water-resistant case.

• Overload protection.

• Igntion protected.

• Reverse polarity protection. Automatic reset.

A 3-bank, 30 amp charger (20A/5A/5A) with a built-in ammeter. The advanced electronic switching technology lets you charge three banks quickly without the excess weight, long charging cycles and annoying hum of old style chargers.

9” W x 12-1/4” H x 7-1/4” D.

116

Order No

293527

Mfg No

2632A

Guest ConnectCharge Inlet

For use with Guest Battery Chargers with Connect Charge Plug only.

Mounts to dash from rear with threaded locking ring or from the front with three screws through fact plate.

Eliminates rewiring, plug snaps into inlet locking tab.

Watertight lid protects AC plug.

List

$677.00

Order No

293573

Prices and specifications subject to change without notice.

Mfg No

150CCI

List

$25.58

BATTERY CHARGERS

Schumacher Ship ‘N Shore Supreme Automatic Battery Charger

The ultimate charger for deep cycle, marine and marine starting batteries. Charges and maintains most Marine Group 24 to 30, 12-Volt wet-cell batteries.

• 12 amp charge is 20% faster than a 10 amp

• Fully Automatic-Automatically maintains the battery when fully charged. Resumes continuous charging when battery becomes discharged.

• Charges up to 16 volts and is suitable for Delco Voyager and similar batteries.

• Manual Operation.

• Microprocessor controlled - provides a 3-step charging system that includes floatmode maintaining and desulfation mode.

• LEDs - Power On, Reversed Hook-up, and Charging and Maintaining.

Schumacher Battery Charger

• 10/2 amp

• 6/12-volt rate

• Excellent full-power charger for any size battery.

• 6” high x 9-1/2” wide x 8” deep.

Order No

220323

Mfg No

87102

Order No

299500

Mfg No

SS120A-PE

List

$109.99

List

$90.00

Schumacher Fully Automatic Battery Charger

• 10/2 amp

• 10 amp rate.

• Reverse polarity protection.

• Fully automatic

• Easy to read meter with LED light that signals when fully charged.

• Charges 12-volt batteries

• 2 Amp trickle/maintenance charge turns on and off ass needed.

• 2 year manufacturer’s limited warranty.

Automatic circuit assures full charge, even on deep cycle batteries. Output shuts off completely at full charge, but turns back on as needed.

Charles Marine 9000 Series Marine Ferroresonant

Battery Chargers

The 9000 Series uses a self-regulating ferroresonant transformer devoid of any complicated switching circuits to charge up to three battery banks simultaneously. Built with rugged stainless steel enclosures and UL recognized, high-quality components to withstand the harsh marine environment. Accurately charge lead-acid batteries only.

Features an easy-to-read ammeter to indicate rate of charge and ignition-protected components for safety. 12 VDC; 24 or 32VDC units available on special order basis.

Dripshield included. 5-year warranty. Made in the USA.

Battery Type: Lead Acid

Battery Banks: 15 AMP = 2, All Others = 3

Charge Voltage: Single Stage 13.8V finish on 12 VDC, 27.6V finish on 24VDC

DC Output Voltage: 12V

AC Input Voltage: 95-140VAC

Frequency: 60Hz

Temperature Range: -25°C to 55°C

Safety Features: Thermal, over current, reverse polarity and ignition protected

Housing: Stainless Steel

Order No

220322

Mfg No

SE-1275A

List

$99.99

Order No

232998

Mfg No

CI1230A

Amp Rating

30

List

$837.02

Schumacher Ship ‘N Shore Charger/ Maintainer/Tester

For 12 Volt Marine, Deep-Cycle, Automotive, AGM and Gel Cell Batteries.

15 Amp Fast Charge - charger monitors battery condition and adjusts charge rate downward to prevent battery damage; for car, truck, marine, RV, farm equipment,

AGM, gel cell and deep- cycle batteries

10 Amp Fast Charge - self-adjusting charge rate for everyday charging needs and keeping your battery in peak condition

2 Amp Slow Charge - for charging small batteries and maintaining large ones; charges motorcycle, ATV, snowmobile and lawn tractor batteries

Easy-To-Read Digital Meter

System Test - helps diagnose problems with battery and charging system*

Charles Marine 5000 Series 24VDC C-Charger

Marine Electronic Battery Chargers

Approved to Marine UL’s 1236 specifications.

20 Amp, 3 Bank

DC ammeter indicates the charge rate. AC and DC fuse protection. Ignition protected

(USCG-33 CFR 183-410). Multi-step charging with temperature compensation. Restores up to 3 individual battery banks simultaneously. Internal temperature compensation automaticaly adjusts output to precisely charge batteries according to ambient conditions. Constructed of tough, anodized aluminum housing that stands up to the elements - including extreme heat, humidity and salt air. Circuit boards with UL recommended coatings provide the ultimate in environmental protection and hydrolyte stability. Exterior slots for easy mounting. Cooling fan operates during peak current demands.

Order No

299537

Mfg No

SSC-1500A

List

$109.99

Order No

234601

Mfg No

93-24205SP-A

Dimensions

13¼” x 9½” x 3.7”

List

$904.12

Prices and specifications subject to change without notice.

117

BATTERY CHARGERS • INVERTERS

ProSport Battery Chargers

• Distributed-On-Demand™ Technology

• Automatically charge and maintain engine crank battery while sensing and distributing 100% of the available charging amps to trolling motor or house bank battery.

• Fully charge and extend the life of your batteries with ProSport’s multi-stage performance charge profiles. Automatically charges and conditions your batteries with a built-in safe maintenance mode for long or short term storage.

• 3 Charge Profiles - User selectable performance charge profiles for: Flooded(leadacid)/STD AGM, GEL & High Performance(HP) AGM.

• High Visibility LED Status Center provides at-a-glance status of: AC Power, Charge

Mode, Battery Type, and Ready/Maintenance Mode.

• Extruded Aluminum Housing for superior heat transfer and durability.

• Dynamic Thermal Output Control controls charging amps while maintaining the recommended charger temperature.

• Compact and rugged design, 100% waterproof and shockproof, dual inline DC safety fuses for trolling motor / accessory battery banks, dynamic thermal output control, over voltage, overload, overtemperature, reverse polarity, and ignition protection.

Prewired for easy installation

Order No Mfg No Voltage Amps Banks List

186001

186012

186023

42006

42012

42021

12

12 or 24

12 or 24 or 36

6

12

20

1

2

3

$129.99

$189.99

$262.00

ProNauticP Series Battery Chargers

Up to 12 performance and precision 4-stage charging profiles: Charge, Condition,

Maintain and Re-condition. Automatic power mode for 12 volt DC lighting and appliances. Factory set for Flooded (Lead Acid) batteries. AGM, GEL selectable.

Auto-ranging (100-250 VAC/50-60Hz) global AC input with reduced harmonic distortion allowing all models to operate off a household power outlet connection. Consumes less power so more AC power is available on board.

Automatically senses and distributes its maximum amp output to any one bank or combination of banks.

Automatically programs conditionaing time based on discharge stage of batteries.

Automatically de-sulfates batteries after 21 days in the maintain mode, improving reserve power performance and extending battery life.

After 72 hours of not seeing a load greater than 5 amps, float voltage will be lowered consuming less energy during storage periods (for flooded and sealed charge profiles).

Real time indication of wiring faults or adverse conditions that may impact the operation of boat’s charging system.

Quiet operation.Automatic temperature compensation and built-in safety remote temperature probe included.

Order No

186034

186045

186056

186067

Mfg No

63120

63130

63140

63180

Amps

20

30

40

30

Banks

3

3

3

3

Voltage

12

12

12

24

List

$422.00

$516.00

$560.00

$890.00

ProTournament Multi-Bank Battery Chargers

• Advanced Electronic, Fully Automatic 3-Step Marine Battery Charger.

• Distributed On-Demand Charging - Automatically senses and distributes a full 10,

15 or 30 amps (model specific) to any one bank or combination of all banks.

• Faster Charging - 2 to 3 times faster than traditional battery chargers with true

3 step charging technology. Each step is electronically controlled for the fastest charge.

• Professional Performance - 100% battery charge guaranteed. 100% charging output with AC power as low as 90 VAC while using long extension cords at the dock, lodging site or home. Proven to condition and extend the life of your batteries.

• Compact Lightweight Design - Rugged Space Saver all aluminum housing is half the height of leading traditional chargers. Unit is not potted and is completely serviceable for lifetime of use under ProMariner’s lifetime repair guarantee.

• Easy Operation - Pre-wired for easy installation. On-board Push-to-Test charge level and mode indicators . Internal battery selection-lead acid, gel or AGM compatible.

• True 3 Step Charging Electronically controlled for the Fastest Charge.

• Distributed On-Demand Charging will automatically distribute its full rated output of

10, 15 or 30 amps (model specific) to any one bank or combination of all battery banks. ProTournament distributes and uses every charging amp with no waste unlike other 2 and 3 bank chargers with an amp limit per bank.

Order No

130231

130230

Mfg No

51015

51020

Voltage

12 or 24

12 or 24

Amps

15

20

Banks

3

2

List

$449.99

$479.99

Cobra Electronics Jumpstarter / Powerpack / Compressor

• Provides AC/DC portable power source anywhere and anytime.

• Runs household appliances up to 100 watts.

• Charge electric devices with USB port at 500mA.

• Super bright emergency light.

• Boost vehicles at 1200 Watts within seconds.

• 260 PSI air compressor.

Order No

389769

Mfg No

CJI250

List

$124.99

118 Prices and specifications subject to change without notice.

JUMPSTARTER - COMPRESSOR • BATTERIES

CPI400 CPI850

Eveready 6 Volt Lighting Battery

Screw type terminals on top of battery.

Order No

220247

List

$7.29

CPI1575 CPI2550

Cobra Electronics Power Inverters

It converts battery power to 120 V AC household power, allowing you to power up office equipment and household appliances from your vehicle. Cigarette lighter cord and direct-to-battery cables are included. This unit is ideal for laptops, 13” TVs, video games, CD players, DVD players, cellular phone chargers and much more!

Duracell Batteries

Order No

389644

389658

389663

389671

Mfg No

CPI480

CPI880

CPI1575

CPI2575

Watts

400

800

1500

2500

List

$69.99

$99.99

$249.99

$399.99

Order No

220020

220897

221859

220019

220878

Mfg No

MN2400B4Z

MN2400B-10Z

MN24B16

MN1500B4Z

MN1500B10Z

Cobra Electronics Inverter Remote Control

Conveniently power on/off your Cobra inverter from a remote location. Includes 20 feet of cable.

This accessory works with the following inverter models:

• CPI 1000

• CPI 1500

• CPI 1550

• CPI 1575

• CPI 2500

• CPI 2550

• CPI 2575

• CPI M1500

• CPI M2200

221837

220017

220805

220016

220793

221826

220021

220885

221848

220022

MN1500B16

MN1400B2Z

MN1400R4Z

MN1300B2Z

MN1300R4Z

MN13R8DW

MN1604B1Z

MN1604B2Z

MN16B4DW

MN908

Order No

389679

Mfg No

CPI A20

List

$39.99

9V

9V

D

D

9V

C

D

AA

C

Size

AAA

AAA

AAA

AA

AA

6V Lantern Spring

Terminal

1

2

4

8

4

4

2

16

2

Pack

4

8

16

4

8

1

$19.95

$5.99

$10.99

$5.99

$10.99

$19.95

$5.99

$10.99

$19.95

List

$5.99

$10.99

$22.95

$5.99

$10.99

$19.99

Cobra Electronics

Microport 130 Watt Power Inverter

• Provides household power on the go! Its swiveling

12 V DC accessory port plug converts your vehicle’s cigarette lighter into 120 Volt AC household power.

• Power up office equipment and appliances under 130 watts, including most laptops.

• Also has a USB output, ideal for using/charging most small video games, an

IPod®, a Blackberry®, mobile phones, and many more USB devices. Its compact size and easy installation makes it ideal for travelers.

Duracell 3 Volt Lithium Batteries

Fits Monocular formerly carried by BOW.

Lithium battery 3 volt, 1400 mAH.

Size (mm): 34 x 16 x 16.

Order No

389615

Mfg No

CPI130

List

$49.99

Order No

221585

Mfg No

DL123ABPK

Prices and specifications subject to change without notice.

List

$8.95

119

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement