E-Pos | 1000 (P4) | User manual | POS 1000 with B49 / B69 / B79 M/B Installation Guide

482000G1

Dec 2004 V2.0

POS 1000

with B49 / B69 / B79

M/B Installation Guide

Safety

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions carefully.Save these instructions for future reference.

2. Follow all warnings and instructions marked on the product.

3. Do not use this product near water.

4. Do not place this product on an unstable cart, stand, or table.The product may fall, causing serious damage to the product.

5. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.

6. This product should be operated from the type of power indicated on the marking label.

If you are not sure of the type of power available, consult your dealer or local power company.

7. Do not allow anything to rest on the power cord.Do not locate this product where persons will walk on the cord.

8. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and

(2) This device must accept any interference received, including interference that may cause undesired operation.

CD-ROM Safety Warning

DANGER

INVISIBLE RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM

Caution on Lithium Batteries

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

2 / 36

Index

1. Accessory....................................................................................................... 4

2. I/O Function.................................................................................................... 5

2.1 POS 1000 Front View .............................................................................. 5

2.2 POS 1000 Rear View............................................................................... 5

3. Specification ................................................................................................... 6

3.1 B69 & B79................................................................................................ 6

3.2 B49 .......................................................................................................... 8

3.3 System Memory Combination................................................................ 10

4. Jumper Setting ............................................................................................. 11

4.1 B69 M/B ..................................................................................................11

4.2 B79 M/B ................................................................................................. 13

4.3 B49 M/B ................................................................................................. 15

4.4 POS I/O Board Jumper Setting.............................................................. 17

5. Driver Installation.......................................................................................... 18

5.1 B69 M/B ................................................................................................. 18

5.2 B79 M/B ................................................................................................. 22

5.3 B49 M/B ................................................................................................. 26

6. Installation Cable Cover ............................................................................... 32

7. Installation the CPU Cooler .......................................................................... 33

8. Installation Cash Drawer .............................................................................. 34

8.1 Cash Drawer Pin Assignment ................................................................ 34

8.2 Cash Drawer Controller register ............................................................ 34

8.3 Cash Drawer control command example............................................... 35

9. Notices ......................................................................................................... 36

9.1 Maximum dimension of Interface card ................................................... 36

3 / 36

1. Accessory

a. Warranty Card c. Drivers Bank d. Installation Guide

b. Power Cable

The following drivers in the folders of Driver Bank are necessary for driver installation.

B69 Mainboard

<CD>:\B69\B69.htm

Folder/File File Description

B69 Driver list

B79 Mainboard

<CD>:\B79\B79.htm

Folder/File File Description

B79 Driver list

B49 Mainboard

Folder/File

<CD>:\B49\B49.htm

<CD>:\Common\VIA\Chipset

4 / 36

File Description

B49 Driver list

Chipset driver

2. I/O Function

2.1 POS 1000 Front View

2

5

6

1

2.2 POS 1000 Rear View

3

4 7

21

17 18 19 20

11

8 9

10 12 13 14 15 16

5

6

7

Slim CD-ROM

Floppy Disc Drive

Compact Flash

12

13

14

Note: DC output 24 V Pin Assignment

COM2

COM1

VGA

# Function # Function

1 Power & HDD Indicator 8 USB 1& 2

2 Key Lock 9 LPT

3

4

Power Button

USB 3 & 4

#

10 PS/2 Keyboard 17

11 PS/2 Mouse 18

Function

15 LAN

16 Audio (MIC & Line In & Line Out)

COM4

DC Output 24V/2.0A

19

20

21

Cash drawer

COM3

AC Inlet

Pin Assignment

1 NC

2 + 24V DC

3 Ground

5 / 36

3. Specification

3.1 B69 & B79

Model

MB

Core logic

1691 1791

B69 all-in-one Mainboard B79 all-in-one Mainboard

Intel 82815E B-STEP GMCH &

82801BA ICH2

Intel 82845GV GMCH &

820801DB ICH4

CPU Intel socket 370 CPU Celeron

/PIII FC-PGA/FC-PGA2

System memory 2x 168pin DIMM sockets support 100/133 MHz SDRAM up to 512MB

BIOS

Video display

Video memory

Award PnP BIOS

Built-in GMCH

Maximum resolution is up to

1600x1200 pixels.

Intel socket 478 CPU Celeron /P4

400/533 FSB with Hyper Threading

Technology support

2 x DDR DIMM 200/266/333 up to

2GB

Built-in GMCH

Maximum resolution is up to

1920x1080 pixels.

The internal graphics device use share system main memory structure and supports Intel Dynamic Video Memory Technology

(D.V.M.T.). Intel D.V.M.T. dynamically responds to application requirements by allocating the proper amount of display and texturing memory taken from system memory by driver control.

1MB On-Chip Frame Buffer Size For legacy OS, user control the for legacy OS. 1MB/8MB On-Chip Frame Buffer

Size by BIOS SETUP.

I/O controller

LAN controller

W83627HF x 1, W83697 HF x1

Realtek RTL8100BL 10/100Mb fast Ethernet controller

Support Wake-On-LAN & boot from LAN

IDE controller Built-in core logic support UDMA 33/66/100Mhz

HDD connector Primary: 1x 40-pin 2.54 pitch

Secondary: 1x 44pin 2.0 pitch, 1x Compact Flash socket

FDD connector 1x 34-pin 2.54 pitch

Audio controller AC’97 AD1881 (2ch)

Expansion Slot

M/B dimension

2x PCI slot

232x313mm

6 / 36

Storage Device

I/O Port Rear Panel:

1 x PS2 keyboard port

1 x PS2 Mouse port

2 x DB-9M RS-232 serial ports

(COM1/COM2, pin1 & 9 with 5V/12V power select)

1 x DB25F Parallel port

1 x DB15F VGA port

1 x RJ45 LAN port

2 x USB ports

1 x Line In,1 x Line out,1 x MIC

POS I/O port

1 x RJ11 cash drawer port

1 x 24V POS printer power port (max. 24V/2A)

2 x DB-9M RS-232 serial ports

(COM3/COM4, pin1 & pin9 with 5V/12V power selectable)

Front Panel:

1x Compact Flash socket

2x USB ports

1 x 3.5” FDD drive

1 x 3.5” HDD drive bay

Optional:

1 x slim CD-ROM /CD-RW/DVD-ROM drive bay

1 x 3.5” HDD drive bay

Power Supply FT818000 internal ATX 180W

System Dimension 300(w) x 335 (d) x 90 (h) mm without cable manage cover

Thermal CPU Cooler x1

Support hardware monitor for fan speed control and software throttling

Customer Display Optional: LED / VFD/ Graphic Customer Display

Pole height (9 /22 cm)

EMC FCC/CE Class B

CE mark: EN55022 / EN61000 -3-2 2000 / EN61000-3-3 / EN55024

Safety

Case Color

OS Support

LVD: EN60950 2000

Computer white/ Silver black

Win98/2000/XP/NT 4.0,Linux

7 / 36

3.2 B49

Model

M/B

Core Logic

1491

B49

VIA CLE266 (VT8623CE) North Bridge

VIA VT8235CD South Bridge

CPU

System Memory 2 x DDR266/200 DIMM up to 2Gbyte memory size

BIOS Award PnP BIOS

Video Display

VIA Eden / C3 EBGA Processors

Support for VIA C3 EBGA processors

133/100/66MHZ CPU Front Side BUS (FSB)

C3 EBGA 733 / 800 / 1.0G / 1.2G or High (Optional)

C3 EBGA 800 Standard to Use

Integrated ProSavage8 2D/3D Video Accelerator

MPEG-2 video textures

2D/3D resolutions up to 1400 x 1050 x 32

Video Memory 16/32/64 MB frame buffer using system memory

I/O Controller Winbond 83697HFx1, 83697HFx1, 83697UFx1

LAN controller Realtek RT8100BL 10/100Mb fast Ethernet controller

Support Wake-On-LAN and boot from LAN

TV – Out PAL / NTSC multi system support

VIA VT1622A TV Out (TV Encoder)

1 x 8pin-header support RCA /S-Video interface (Optional)

HDD connector Primary: 1x 40-pin 2.54 pitch

Secondary: 1x 44pin 2.0 pitch, 1x Compact Flash socket

FDD connector 1x 34-pin 2.54 pitch

USB Controller VT8235 Integrated support USB2.0

Audio controller AC’97 Realtek ALC202A (2ch)

Expansion Slot 2 x PCI slot

M/B dimension 232 mm (W) x 314 mm (D)

Storage Device 1 x 3.5” FDD drive

1 x 3.5” HDD drive bay

Optional:

1 x slim CD-ROM /CD-RW/DVD-ROM drive bay

1 x 3.5” HDD drive bay

Power supply FT818000 internal ATX 180W

System dimension 300(w) x 335 (d) x 90 (h) mm without cable manage cover

Thermal CPU Cooler x1

Support hardware monitor for fan speed control and software throttling

Customer Display Optional: LED / VFD/ Graphic Customer Display

Pole height (9 /22 cm)

8 / 36

EMI

Safety

I/O port

Case Color

OS Support

CE Class B

FCC Class B

LVD: EN60950 2000

Rear Panel:

2 x USB 2.0 ports

1 x DB-25F Parallel port

1 x 1*6Pin Double PS2 Keyboard / Mouse port

2 x DB-9M RS-232 Serial port

1 x DB-15F VGA port

1 x RJ-45 LAN port

1 x Audio jacks: line-out

1 x Line In

1 x Line out

1 x MIC

POS I/O port

1 x RJ11 cash drawer port

1 x 24V POS printer power port (max. 24V/2A)

2 x DB-9M RS-232 serial ports

(COM3/COM4, pin1 & pin9 with 5V/12V power selectable)

Option1:

1 x 2 nd

printer port on slot bracket

Option2:

2 x USB 2.0 ports (for slot user, support pin header)

Front Panel:

2 x USB 2.0 ports

1 x compact flash

Computer white/ Silver black

Windows 9x/ME/NT 4.0/2000/XP

Linux

9 / 36

3.3 System Memory Combination

3.3.1 POS 1000 B69 M/B

RAM Size

Slot

128MB 256MB 512MB

DIMM1 X 256 X

DIMM2 128 X 128 X 256

3.3.2 POS 1000 B79 M/B

RAM Size

Slot

DIMM1

128MB 256MB 512MB 1024MB 2048MB

X 128 128 256 X 256 512 X 512 1024 X 1024

DIMM2 128 X 128 X 256 256 X 512 512 X 1024 1024

Note:

1. Optimal Combination

CPU system bus

DIMM

400

DDR 266

533

DDR 333

2. In B79 memory 2048MB combination, if you want to use double stack memory that your DIMM1 and DIMM2 all should be double stack memory.

3.3.3 POS 1000 B49 M/B

RAM Size

Slot

DIMM1

128MB 256MB 512MB 1024MB 2048MB

X 128 128 256 X 256 512 X 512 1024 X 1024

DIMM2 128 X 128 X 256 256 X 512 512 X 1024 1024

10 / 36

4. Jumper Setting

4.1 B69 M/B

VGA1

RJ45-1

COM1 COM2

DIMM1 DIMM2

PS1

JP1

DATA1

JP2

U11

CN1

JP3 JP7

JP5

JP4 JP6

U14

CN2

FDD1

U7

PRN1

U8

IDE2

CN4

USB1

U46

PWR1

CN5

U47

BAT4

FAS_CPU1

U45

U24

IDE3

FAS_SYS1

U49

CN9

SW1

USB2 USB3

CN6

11 / 36

4.1.1 COM 1 Power Selection * Default Setting

Pin Function JP1 (SHORT)

*DCD# 1-2

1

VCC 3-4

9

+12V 5-6

*RI# 7-8

VCC 9-10

+12V 11-12

4.1.2 COM 2 Power Selection

Pin

1

9

Function JP2 (SHORT)

*DCD# 1-2

VCC 3-4

+12V 5-6

*RI# 7-8

VCC 9-10

+12V 11-12

4.1.3 Power Mode Selection

Function

*ATX Power

AT Power

4.1.4 CMOS Operation mode

Function

*CMOS Normal

CMOS Reset

JP3

OPEN

SHORT

JP6

OPEN

SHORT

4.1.5 Compact Flash Master/Slave Setting

Function JP7

*Master OPEN

Slave SHORT

Note:

OPEN

SHORT

12 / 36

4.2 B79 M/B

VGA1

RJ45-1

COM1

DIMM1 DIMM2

COM2

PS1

JP1

DATA1

JP2

U11

CN1

JP3 JP7

JP5

JP4 JP6

U14

CN2

FDD1

U7

PRN1

U8

IDE2

CN4

USB1

U18

PWR1

CN5

U19

FAN-SYS

BAT1

PWR2

FAN-CPU

U24

IDE3

CPU1

CN9

SW1

USB2 USB3

CN6

13 / 36

4.2.1 COM 1 Power Selection * Default Setting

Pin Function JP1 (SHORT)

*DCD# 1-2

1

VCC 3-4

9

+12V 5-6

*RI# 7-8

VCC 9-10

+12V 11-12

4.2.2 COM 2 Power Selection

Pin

1

9

Function JP2 (SHORT)

*DCD# 1-2

VCC 3-4

+12V 5-6

*RI# 7-8

VCC 9-10

+12V 11-12

4.2.3 Power Mode Selection

Function

*ATX Power

AT Power

4.2.4 CMOS Operation mode

Function

*CMOS Normal

CMOS Reset

JP3

OPEN

SHORT

JP6

OPEN

SHORT

4.2.5 Compact Flash Master/Slave Setting

Function JP7

*Master OPEN

Slave SHORT

Note:

OPEN

SHORT

14 / 36

4.3 B49 M/B

15 / 36

4.3.1 COM1 Power Select * Default Setting

Pin Function JP1(SHORT)

*DCD# 1-2

1

9

+5V 3-4

+12V 5-6

*RI# 7-8

+5V 9-10

+12V 11-12

4.3.2 COM2 Power Select

Pin Function JP2 (SHORT)

1

*DCD# 1-2

+5V 3-4

+12V 5-6

*RI# 7-8

+5V 9-10 9

+12V 11-12

4.3.3 Power Mode Setting

Function

* ATX Power

JP3 (SHORT)

1-2

AT Power 2-3

4.3.4 CMOS Clear Selection

Function JP6 (SHORT)

* Normal 1-2

Clear 2-3

4.3.5 Compact Flash Master/Slave Setting

Function

* Master

JP7

SHORT

Slave OPEN

Note:

OPEN

SHORT

16 / 36

4.4 POS I/O Board Jumper Setting

4.4.1 COM 3 Power Selection * Default Setting

Pin Function JP4 (SHORT)

*DCD# 1-2

1

VCC 3-4

9

+12V 5-6

*RI# 7-8

VCC 9-10

+12V 11-12

4.4.2 COM 4 Power Selection

Pin

1

9

Function JP3 (SHORT)

*DCD# 1-2

VCC 3-4

+12V 5-6

*RI# 7-8

VCC 9-10

+12V 11-12

4.4.3 Cash Drawer Power Selection

Function JP2 (SHORT)

24V 1-2

*12V 2-3

Note:

OPEN

SHORT

17 / 36

5. Driver Installation

5.1 B69 M/B

The following procedures are for Windows 98SE, other platforms are similar.

5.1.1 Chipset Driver Installation

Driver path: <CD>:\Common\INTEL\Chipset a. Click "Intel_Chipset_4_20_1006" on the

My Computer window.

b. Click "Next" button on the Welcome window. c. Click "Next" button on the License

Agreement window.

d. Click "Next" button on the Read me

Information window.

18 / 36

e. Click ”Finish” and restart your system.

5.1.2 VGA Driver Installation

Driver path: <CD>:\Common\INTEL\i815VGA a. Click "Setup" on the My Computer window.

b. Click "Next" button on the Welcome window. c. Click "Next" button on the License

Agreement window.

d. Click ”Finish” and restart your system.

19 / 36

5.1.3 LAN Driver Installation

Driver path: <CD>:\Common\Lan_driver\R8139_810x) a. Click ”Setup” on the My computer windows.

b. Click "Finish" button on the Maintenance complete window. c. Click ”OK” to restart the system.

20 / 36

5.1.4 Audio Driver Installation

Driver path: <CD>:\Common\Ac97_codec\ADI\AD1881A a. Click ” Next” button on the Add New

Hardware Wizard window.

b. Click ” Next” on the Add New Hardware

Wizard window. c. Browse the driver path and Click “Next” button.

d. Click ” Next” button on the Add New

Hardware Wizard window. e. Click ” Finish” button on the Add New

Hardware Wizard window.

21 / 36

5.2 B79 M/B

The following procedures are for Windows 2000, other platforms are similar.

5.2.1 Chipset Driver Installation

Driver path: <CD>:\Common\INTEL\Chipset a. Click ” Intel_Chipset_4_20_1006” on the b. Click “Next” button on the Setup window.

My computer windows. c. Click "Yes" button on the License

Agreement window.

d. Click "Next" button on the ReadME window. e. Click ”Finish” to restart the system.

22 / 36

5.2.2 VGA Driver Installation

Driver path: <CD>:\Common\INTEL\i845VGA a. Click ” Setup” on the My computer windows.

b. Click “Next” button on the Welcome window. c. Click "Yes" button on the License

Agreement window.

d. Click ”Finish” to restart the system.

23 / 36

5.2.3 LAN Driver Installation

Driver path: <CD>:\Common\LAN_driver\R8139_810x) a. Click “Setup” on the My computer window.

b. Click “Next” button on the Welcome window. c. Click “Finish” on the LanSetup window.

24 / 36

5.2.4 Audio Driver Installation

Driver path: <CD>:\Common\Ac97_codec\ADI\AD1881A a. Click ” Next” button on the Add New

Hardware Wizard window.

b. Click ” Next” on the Add New Hardware

Wizard window. c. Browse the driver path and Click “Next” button.

d. Click ” Next” button on the Add New

Hardware Wizard window. e. Click ” Finish” button on the Add New

Hardware Wizard window.

25 / 36

5.3 B49 M/B

The following procedures are for Windows XP, other platforms are similar.

5.3.1 Chipset Driver Installation

Driver path: <CD>:\Common\VIA\Chipset) a. Click “VIAHyperion4in1453v” on the My computer window.

b. Click “Next” button on the Welcome window. c. Click “Yes” button on the ReadME window.

d. Click “Next” button on the 4in1 Setup

Mode Option window.

26 / 36

e. Click “Next” button on the Setup

Component window.

f. Click “Next” button on the VIA PCI IDE

Bus Driver window. g. Click “Next” button on the VIA_GART

AGP Driver window.

h. Click “OK” button to restart the system.

27 / 36

5.3.2 VGA Driver installation

Driver path: <CD>:\Common\VIA\VGA\CLE266) a. Click “Setup” on the My computer window.

b. Click “Next” button on the Welcome window. c. Click “Next” button on the Start Copying

Files window.

d. Click “Continue Anyway” button on the

Hardware Installation window. e. Click “Finish” button to restart the system.

28 / 36

5.3.3 LAN Driver Installation

Driver path: <CD>:\Common\LAN_driver\R8139_810x) a. Click “Setup” on the My computer window.

b. Click “Next” button on the Welcome window. c. Click “Finish” button on the LanSetup window.

29 / 36

5.3.4 Audio Driver Installation

Driver path: <CD>:\Common\Ac97_codec\Realtek\ALC202A) a. Click “wdm_a3631” on the My computer b. Click “Next” button on the Welcome window. window. c. Click “Continue Anyway” button on the

Hardware Installation window.

d. Click ”Finish” button to restart system.

30 / 36

5.3.5 USB 2.0 Driver Installation

Driver path: <CD>:\Common\VIA\USB2.0) a. Click “Setup” on the My computer window.

b. Click “Next” button on the Welcome window. c. Click “Next” button on the Setup

Component window.

d. Click ”Yes” button to restart system.

31 / 36

6. Installation Cable Cover

a. Loosen the four screws (4mmx3, 6mmx1 (32UCN )). b. Insert the screw (8mm) into the plastics. c. Lock the two screws. d. Lock the brackets with 6 mm screws. e. Installation the cable cover. f. Finished.

32 / 36

7. Installation the CPU Cooler

(Note: Only for B79 Mainboard) a. Loosen the four screws to release the vent tube. b. Combination the CPU cooler and vent tube.

c. Connection the CPU cooler connector.

1

3

2 4 d. Lock the four screws on the Mainboard.

33 / 36

8. Installation Cash Drawer

You can install a cash drawer through the Cash Drawer port.

8.1 Cash Drawer Pin Assignment

Pin Signal

1 GND

4 12V/24V

6 GND

Data out address (200h)

Data in address (201h)

8.2 Cash Drawer Controller register

The Cash Drawer Controller use two I/O addresses to control Cash Drawer –Cash Drawer

Control Register and Cash Drawer Status Register.

8.2.1 Cash Drawer Control Register

Register Location: 200h

Size: 8bit

7 6 5 4 3 2 1 0

X X X X X X

Cash Drawer “DOUT bit0” pin output control

Cash Drawer “DOUT bit1” pin output control

Reserved

Bit 7-2: Reserved

Bit 1: Cash Drawer “DOUT bit1” pin output control.

= 1: Opening the Cash Drawer

= 0: Allow close the Cash Drawer

Bit 0: Cash Drawer “DOUT bit0” pin output control.

= 1: Opening the Cash Drawer

= 0: Allow close the Cash Drawer

Note: Please follow the Cash Drawer control signal design to control the Cash Drawer.

Suggest control the bit1/0 at the same time.

34 / 36

8.2.2 Cash Drawer Status Register

Register Location: 201h

Size: 8bit

7 6 5 4 3 2 1 0

X X X X X X X

Cash Drawer “DIN bit0” pin output control

Reserved

Bit 7-1: Reserved

Bit 0: Cash Drawer “DIN bit0” pin input status.

= 1: the Cash Drawer opened or not exist.

= 0: the Cash Drawer closed.

8.3 Cash Drawer control command example

Use Debug.EXE program under DOS or Windows98

Command

O 200 01

Cash Drawer

Opening

O 200 00 Allow to close

¾ Set the I/O address 200h bit0 =1 for opening Cash Drawer by “DOUT bit0” pin control.

¾ Set the I/O address 200h bit0 = 0 for allow close Cash Drawer.

Command Cash Drawer

I 201 Check status

¾ The I/O address 201h bit0 =1 mean the Cash Drawer is opened or not exist.

¾ The I/O address 201h bit0 =0 mean the Cash Drawer is closed.

35 / 36

9. Notices

9.1 Maximum dimension of Interface card

(Maximum dimension of Interface card: 183 mm x 104 mm)

183mm

104 mm

36 / 36