Murphy TTD Annunciators Quick Start Guide

Below you will find brief information for TTD. This quick start guide helps users configure the TTD Annunciator using MConfig software. It covers opening configuration templates, setting port parameters, and performing uploads or downloads to synchronize settings. The guide also explains how to handle common errors during configuration, ensuring optimal operation for your device.

PDF

Document

nd
5311 S. 122 East Avenue
Tulsa, OK 74146
918-317-4100
www.fwmurphy.com
December 10, 2004
MCONFIG Quick Start Guide to Configure TTD
After installing MConfig, run the program and choose Open from the File menu.
In the Open dialog, choose Files of type and select the TTD Configuration as shown below. This action
will filter the files to show only templates related to TTD.
Choose a template saved from a previous session or the Default.TTD template. When the proper file
has been selected, click Open.
Confidential
Page 1 of 3
MConfig Quick Start for TTD .doc
nd
5311 S. 122 East Avenue
Tulsa, OK 74146
918-317-4100
www.fwmurphy.com
After loading the desired template, choose Port Settings from the Transfer menu. The setting
requirements vary for different devices.
The graphic below depicts the requirements for the TTD Annunciator. Make the necessary adjustments
to the settings and click Ok. To access some of the parameters shown, click the Advanced button.
The TTD will not accept Modbus writes for some registers while in the Run Mode. To perform a
complete Download, it is necessary to be in Shutdown Mode on the TTD.
To connect with the TTD, choose Upload or Download from the Transfer menu. Upon completing a
Transfer the TTD is connected to MConfig and polling will be continuous.
The Status of the connection is shown at the bottom of the MConfig client window. The Status for the
connection will be Offline until a successful Upload or Download has been performed. The Status will
change to Online when MConfig is continuously polling (reading) information from the TTD.
Use Upload to read parameters from the TTD into MConfig. This action overwrites any values
currently set in the loaded template with the parameters stored in the TTD.
Once the reading have been updated to MConfig the information can be saved to a file or modifications
can be made to the TTD in real time by changing a value of a parameter while connected.
This method is best for making minor changes to parameter in the TTD without affecting all settings.
Because Upload begins by first synchronizing MConfig with settings in the TTD, only changes made to
parameters while connected with MConfig will be changed in the TTD.
To configure the TTD with a desired template of settings use Download from the Transfer menu. This
action overwrites any values currently set in the TTD with parameters from the loaded template. There
are certain rules that the TTD adheres to in order to prevent improper setup. During Download, settings
that violate these rules will cause an error to be logged. In some instances, the captured errors may
also be related to communication problems.
MConfig will attempt to write each parameter up to the number of retries configured in the Port Settings
dialog. If the TTD responds with an exception, MConfig will continue to Download all parameters
before displaying the MConfig Transfer Status dialog. If no errors are detected, MConfig will enter the
Online mode and continuously poll the TTD without displaying the MConfig Transfer Status dialog.
Confidential
Page 2 of 3
MConfig Quick Start for TTD .doc
nd
5311 S. 122 East Avenue
Tulsa, OK 74146
918-317-4100
www.fwmurphy.com
The graphic below depicts a typical error that occurs when Downloading a configuration to the TTD.
The Sensor Mode Setting, for example, can cause the errors shown below.
Because the TTD will not allow individual channels Sensor Types to be set when the Sensor Mode
Setting is set to a value other than zero, the TTD responds with Illegal Data Value when MConfig
attempt to write to these parameters.
If the errors reported are Response: Illegal Data Value, some of the rules have been violated and some
parameters stored in the template may not have been Downloaded to the TTD. This is normal and
expected because MConfig does not know the rules, it just attempts to Download all settings.
To continue in Online mode, just press Connect on the MConfig Transfer Status dialog. It is always a
good idea to verify all the settings meet requirements before ending any session.
To end a session, choose Disconnect from the Transfer menu. After the status line shows Offline, any
changes made to parameters are not changed in the connected TTD.
Save
If the settings need to be preserved for later Download or reference, just Save the template using the
Save As choice in the File menu.
Print
A document reference can be generated by using the Print function from the file menu. Use either
Print Page or Print All to generate a copy of all the parameters from the loaded template. This can be
done Online or Offline, however, values may be changing if connected to a TTD in Online mode.
Confidential
Page 3 of 3
MConfig Quick Start for TTD .doc
">

Hello! I am your AI assistant, and I've reviewed the MCONFIG Quick Start Guide for the Murphy TTD Annunciator. This document details how to use MConfig software to set up and manage your TTD device, covering essential steps like loading templates, configuring port settings, and performing data transfers. I can help you understand the connection process, troubleshoot common download errors, or clarify any specific parameters. Feel free to ask me anything about configuring your TTD!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

MConfig software configuration
Supports TTD Annunciator device
Upload/Download device parameters
Modbus write compatibility
Run and Shutdown modes for configuration
Error logging during download
Online/Offline connection status monitoring
Parameter saving and printing capabilities

Frequently asked questions

After installing MConfig, run the program, choose Open from the File menu, and select a TTD Configuration template (like Default.TTD).

The TTD must be in Shutdown Mode to accept Modbus writes for a complete download of parameters.

When the Status changes to "Online", it means MConfig is successfully connected to the TTD and is continuously polling (reading) information from it.

This error often occurs when MConfig attempts to write parameters that violate the TTD's internal rules, such as trying to set individual channel Sensor Types when the Sensor Mode Setting is not zero.