Standard Horizon CP190i CPF190i Owner's Manual

PDF

Document

CP190i - GPS Chart Plotters
CPF190i - GPS Chart Plotters/Fish Finder
Owner's Manual
CP190i
CPF190i
WARNING!!!
Electronic charts displayed by the GPS Chart Plotter are believed to be accurate and
reliable, but are not intended to be a substitute for the official charts, which should
remain your main reference for all matters related to the execution of safe
navigation.
For this reason you should always keep the official published and approved nautical
charts on board.
FCC Compliance Statement
This device complies with Part 15 of the FCC limits for Class A digital devices. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed or used in accordance with the instructions may cause harmful interference
with radio communications.
There is no guarantee that interference will not occur in a particular instance. If this
equipment does cause harmful interference to other equipment, try to correct the
problem by relocating the equipment.
Consult an authorized STANDARD HORIZON dealer or other qualified service
technician if the problem cannot be corrected. Operation is subject to the following
conditions: (1) This device cannot cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
Copyright 2011. VERTEX STANDARD CO., LTD. All rights reserved. Printed in Italy.
No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD.
OM
CODE:
Page
4 S4x2SH5c_0ww 16.50bD78 - 310311
CP190i and CPF190i
CAUTION
- The GPS Chart Plotter is designed for maritime use. To avoid water intrusion,
ensure the C-MAP BY JEPPESEN C-CARD door is completely closed.
- Extensive exposure to heat may result in damage to the GPS Chart Plotter.
- The GPS Chart Plotter contains dangerous high-voltage circuits which only
experienced technicians can handle.
- STANDARD HORIZON will not be liable for errors contained herein, or for
incidental or consequential damages in connection with the performance or use
of this material.
CLEANING PROCEDURE FOR THE GPS CHART PLOTTER SCREEN
Cleaning of the chart plotter screen is a very important operation and must be done
carefully. Since the surface is covered by a antireflective coating, the procedure for
cleaning all the surfaces can be performed using the following procedure: Use a
clean, soft, lint-free cloth to clean the glass. We recommend using a micro-fiber
cloth. Spray a small amount of ammonia-free cleaner (isopropyl alcohol) onto the
cloth. Spraying on the cloth will prevent overspray. Fold the cloth or lens cloth into
a triangular shape, moisten the tip and use the index finger behind a corner to move
the cloth across the surface in overlapping side to side strokes. If the cloth is too wet,
a noticeable wet film will be left in its path and you will need to repeat the process.
If tooand
dry,
the cloth won’t glide easily, and may damage the surface.
CP190i
CPF190i
Page 5
Page
6
CP190i and CPF190i
TABLE OF CONTENTS
1. INTRODUCTION ................................................................................................................. 13
1.0 GENERAL INFORMATION .................................................................................... 13
1.1 PACKING LIST ....................................................................................................... 14
1.1.0 Packing List ................................................................................................ 14
1.2 OPTIONAL DOME OR OPEN ARRAY RADAR ANTENNAS ................................ 14
1.3 OPTIONAL ACCESSORIES .................................................................................. 15
2. INSTALLATION ................................................................................................................... 17
2.0 MOUNTING THE GPS CHART PLOTTER ............................................................ 17
2.1 BRACKET MOUNTING .......................................................................................... 17
2.2 FLUSH MOUNTING ................................................................................................ 18
2.3 MOUNTING THE OPTIONAL EXTERNAL GPS ANTENNA ................................. 19
2.3.0 Flush mounting the antenna ...................................................................... 19
2.4 CONNECTIONS ..................................................................................................... 20
2.4.0 CP190i Connection Table .......................................................................... 21
2.4.1 CP190i Connections .................................................................................. 21
2.4.2 CPF190i Connection Table ........................................................................ 23
2.4.3 CPF190i Connections ................................................................................ 23
2.5 BATTERY CONNECTIONS ................................................................................... 25
2.6 NMEA CONNECTIONS .......................................................................................... 25
2.7 GPS POSITION ON A VHF RADIO ....................................................................... 25
2.8 CP190i: OPTIONAL BLACK BOX FISH FINDER .................................................. 25
2.9 RADAR ANTENNA (USA ONLY) ........................................................................... 26
2.10 PERSONAL COMPUTER CONNECTIONS ........................................................... 26
2.11 NMEA DATA PAGE ................................................................................................ 27
2.12 DEMO MODE (For DEALER USE) ........................................................................ 27
3. CONTROLS AND INDICATORS ...................................................................................... 29
3.0 CONTROLS AND CONNECTIONS ....................................................................... 29
3.1 GETTING STARTED .............................................................................................. 30
3.1.0 Power On, Off and ShuttlePoint Knob operation ...................................... 30
3.1.1 Cursor Vs. Home Mode ............................................................................. 32
3.1.2 Cursor and Menu selection speed ............................................................. 32
3.1.3 Changing the Ship Icons ........................................................................... 33
3.1.4 Changing the Backlight and Contrast ........................................................ 33
3.1.5 Selecting North Up or Course Up .............................................................. 33
3.2 AUTOMATIC TIME ................................................................................................. 34
3.3 SELECTING LORAN TD OR OTHER COORDINATE SYSTEM .......................... 35
3.4 CHANGING THE CHART COLOR ......................................................................... 36
3.5 SELECTING LANGUAGE ...................................................................................... 36
3.6 SETTINGS IN GENERAL SETUP MENU .............................................................. 38
3.7 ABOUT PAGE ........................................................................................................ 39
4. FIND SERVICES ............................................................................................................... 41
4.0 USING FIND SERVICES &amp; MORE FUNCTIONS .................................................. 41
4.0.0 Port Services .............................................................................................. 41
4.0.1 Port ............................................................................................................. 42
CP190i and CPF190i
Page 7
4.0.2
4.0.3
4.0.4
4.0.5
4.0.6
4.0.7
4.0.8
4.0.9
4.0.10
Tide Stations .............................................................................................. 42
Wrecks ....................................................................................................... 43
Obstructions ............................................................................................... 44
Lakes Information ...................................................................................... 45
Lakes By Name ......................................................................................... 47
Points Of Interest ....................................................................................... 47
User Points ................................................................................................ 48
Coordinates ................................................................................................ 48
Information ................................................................................................. 49
5. MAX CARTOGRAPHY OVERVIEW ................................................................................. 51
5.0 BUILT-IN CHARTS ................................................................................................. 51
5.0.0 Coverage areas and details ....................................................................... 51
5.0.1 Updating Built-In Charts ............................................................................. 51
5.1 INSERTING THE OPTIONAL MAX C-CARD ........................................................ 52
6. MAP FUNCTIONS ............................................................................................................ 55
6.0 MAX FUNCTIONS MENU ...................................................................................... 55
6.0.0 Zoom Type ................................................................................................. 55
6.0.1 Icon Size .................................................................................................... 56
6.0.2 Place Name Size ....................................................................................... 56
6.0.3 Perspective View ....................................................................................... 57
6.0.4 Dynamic Nav-Aids ..................................................................................... 58
6.0.5 Safety Status Bar (DSI - Data Safety Indicator) ........................................ 58
6.0.6 Satellite Imagery ........................................................................................ 59
6.0.7 Currents Prediction .................................................................................... 60
6.0.8 Chart Language ......................................................................................... 61
6.0.9 Pictures or Diagrams ................................................................................. 61
How to show the Pictures or Diagrams of a Object .................................. 62
6.0.10 Enhanced Port Info .................................................................................... 63
7. CREATING MARKS ......................................................................................................... 65
7.0 CREATING A NEW MARK USING THE CHART PAGE ....................................... 65
7.1 EDITING A MARK .................................................................................................. 65
7.1.0 Deleting a Mark or Waypoint ..................................................................... 66
7.1.1 Moving a Mark or Waypoint ....................................................................... 66
7.2 MARKS/WAYPOINTS LIST ................................................................................... 67
7.3 CREATING A NEW MARK WITH THE USER POINTS LIST ............................... 68
7.4 GOTO CURSOR, ROUTE AND MARK .................................................................. 69
8. MAN OVER BOARD (MOB) FUNCTION ......................................................................... 71
8.0 PLACING A MOB POINT ....................................................................................... 71
8.1 DELETING A MOB POINT ..................................................................................... 71
9. ROUTES ........................................................................................................................... 73
9.0 CREATING A ROUTE USING WAYPOINTS ........................................................ 73
9.1 CHANGING THE NAME OF A ROUTE ................................................................. 74
9.2 CREATING AN OLYMPIC ROUTE ........................................................................ 74
9.3 MAKING ADDITIONAL ROUTES ........................................................................... 75
9.4 CREATING A ROUTE USING MARKS ON THE CHART PAGE .......................... 75
9.5 INSERTING A WAYPOINT INTO A ROUTE ......................................................... 76
9.6 GOTO A ROUTE .................................................................................................... 77
9.6.0 Using [GOTO] to select Route ................................................................... 77
Page
8
CP190i and CPF190i
9.7
9.8
9.6.1 Using the ShuttlePoint knob ...................................................................... 77
DELETING A ROUTE ............................................................................................. 77
OTHER SETTINGS IN ROUTE MENU .................................................................. 78
9.8.0 Route Check .............................................................................................. 78
10. TRACKS ............................................................................................................................ 81
10.0 TRACKING ............................................................................................................. 81
10.0.0 Saving and starting a new Track ............................................................... 82
10.0.1 Deleting a Track ......................................................................................... 82
10.0.2 Other settings ............................................................................................. 82
10.1 TRIP LOG ............................................................................................................... 83
10.1.0 Using the Trip Log ..................................................................................... 83
10.1.1 Setup / Reset ............................................................................................. 83
11. USER C-CARD ................................................................................................................. 85
11.0 USER C-CARD MENU ........................................................................................... 85
11.0.0 Formatting the optional User C-CARD ...................................................... 85
11.0.1 Transferring files to the optional User C-CARD ........................................ 85
11.0.2 Loading a file from the optional User C-CARD ......................................... 86
11.0.3 Deleting a file from the optional User C-CARD ......................................... 86
11.0.4 Refreshing the optional User C-CARD ...................................................... 86
12. PAGES .............................................................................................................................. 87
12.0 CHART PAGE ......................................................................................................... 87
12.0.0 Change Focus on Dual Chart Page .......................................................... 88
12.0.1 Single Chart Page ...................................................................................... 88
12.0.2 Window Selections .................................................................................... 89
12.0.3 Customizing the Data Windows ................................................................ 89
12.0.4 Additional Functions on Chart Page .......................................................... 90
12.0.5 Turning Off Information on Icon Points ..................................................... 91
12.0.6 Display Mode ............................................................................................. 91
12.0.7 Marine Settings .......................................................................................... 92
12.0.8 Depth Settings ........................................................................................... 93
12.0.9 Land Settings ............................................................................................. 93
12.0.10 Chart Settings ............................................................................................ 93
12.0.11 Underwater Objects Settings ..................................................................... 95
12.1 CUSTOMIZING CHART SETTINGS ...................................................................... 95
12.2 NAVIGATION PAGE .............................................................................................. 95
12.3 HIGHWAY PAGE ................................................................................................... 96
12.4 CELESTIAL PAGE ................................................................................................. 97
Changing date ......................................................................................................... 97
12.5 GPS STATUS PAGE .............................................................................................. 98
12.5.0 WAAS/EGNOS Setting .............................................................................. 98
12.5.1 Setup Menu ................................................................................................ 99
12.6 NMEA DISPLAY PAGE .......................................................................................... 99
Changing the NMEA Page Windows ................................................................... 100
12.7 NMEA DATA PAGE .............................................................................................. 100
12.8 NMEA TREND PAGES ........................................................................................ 101
12.9 VHF DIGITAL SELECTIVE CALLING .................................................................. 102
12.9.0 Interfacing ................................................................................................ 102
12.9.1 Distress Call ............................................................................................. 102
12.9.2 Position Request ...................................................................................... 103
CP190i and CPF190i
Page 9
13. ADVANCED SETTINGS ................................................................................................. 105
13.0 INPUT/OUTPUT (NMEA, AIS, RADAR) .............................................................. 105
13.0.0 Input ......................................................................................................... 105
13.0.1 Ouput ....................................................................................................... 105
13.1 NAVIGATE ............................................................................................................ 106
13.1.0 Loran TD .................................................................................................. 107
13.2 COMPASS ............................................................................................................ 107
13.3 ALARMS ............................................................................................................... 107
13.4 SIMULATION ........................................................................................................ 108
13.4.0 Navigating a Route in Simulation mode .................................................. 109
13.5 DSC POLLING ...................................................................................................... 109
14. AIS ................................................................................................................................... 111
14.0 SYSTEM DEFINITIONS ....................................................................................... 111
14.1 MENU .................................................................................................................... 112
14.2 AIS SETUP ........................................................................................................... 112
14.3 QUICK INFO ON AIS TARGET ............................................................................ 112
14.4 LIST ....................................................................................................................... 113
14.5 AIS TARGET COLORS ........................................................................................ 114
15. C-WEATHER SERVICE .................................................................................................. 115
15.0 C-WEATHER SERVICE MENU ........................................................................... 115
15.0.0 Download ................................................................................................. 115
15.0.1 Copy From User C-CARD ....................................................................... 116
15.0.2 Weather Forecast .................................................................................... 116
15.0.3 Real Time View ........................................................................................ 116
15.0.4 Type of Data ............................................................................................ 116
16. MOBILARM ..................................................................................................................... 117
16.0 MOBILARM-GPS CHART PLOTTER CONNECTION ......................................... 117
16.1 SOFTWARE SETUP ............................................................................................ 118
16.2 MOBILARM STATUS ........................................................................................... 118
16.3 MOBILARM PTX ................................................................................................... 119
16.3.0 MOBILARM MOB alert is received .......................................................... 119
16.4 PLACING CURSOR ON THE PTX ICON ............................................................ 120
16.4.0 Delete PTX ............................................................................................... 120
16.4.1 Goto PTX ................................................................................................. 120
16.4.2 The MOBILARM Alarm Status List .......................................................... 121
17. FISH FINDER for CPF190i ............................................................................................ 123
17.0 ENABLE/DISABLE ............................................................................................... 123
17.1 UNDERSTANDING THE FISH FINDER PAGE ................................................... 124
17.1.1 Understanding the Fish Finder display .................................................... 125
17.2 DISPLAYING THE FISH FINDER PAGE ............................................................. 126
17.2.0 Auto Full Page ......................................................................................... 127
17.2.1 200 kHz Full, 50 kHz Full and 50&amp;200kHz Display Pages ..................... 127
17.2.2 200 kHz and 50 kHz Zoom Pages ........................................................... 127
17.2.3 200 kHz and 50 kHz Fish/Chart Pages ................................................... 128
17.3 SETUP MENU ...................................................................................................... 128
17.4 FISH FINDER COLOR ......................................................................................... 128
17.5 PRESETS ............................................................................................................. 129
17.6 FREQUENCY ....................................................................................................... 129
17.7 GAIN MODE ......................................................................................................... 130
Page 10
CP190i and CPF190i
17.8
17.9
17.10
17.11
17.12
17.13
17.14
17.15
17.16
17.7.0 Auto Mode ................................................................................................ 130
17.7.1 Manual Mode ........................................................................................... 130
RANGE MENU ...................................................................................................... 130
17.8.0 Range Mode ............................................................................................. 130
17.8.0.0Manual Mode .............................................................................. 130
17.8.0.1Auto Range ................................................................................. 130
17.8.0.2Bottom Lock ............................................................................... 130
17.8.1 Depth ........................................................................................................ 131
17.8.2 Shift .......................................................................................................... 131
INTERFERENCE REJECTION ............................................................................ 131
SENSITIVITY MENU ............................................................................................ 131
17.10.0 Gain .......................................................................................................... 132
17.10.1 STC (Sensitivity Time Control) ................................................................ 132
17.10.2 Surface Noise Filter ................................................................................. 133
DISPLAY SETUP .................................................................................................. 134
17.11.0 Color Settings .......................................................................................... 134
17.11.1 Scrolling Speed ........................................................................................ 134
17.11.2 White Line ................................................................................................ 134
17.11.3 Fish Symbols ........................................................................................... 135
17.11.4 A-Scope ................................................................................................... 135
TRANSDUCER SETUP ........................................................................................ 135
17.12.0 Keel Offset ............................................................................................... 135
17.12.1 Calibrate Water Speed ............................................................................ 135
17.12.2 Calibrate Water Temp ............................................................................. 135
17.12.3 Set Defaults ............................................................................................. 135
ALARMS ............................................................................................................... 136
17.13.0 Shallow Water .......................................................................................... 136
17.13.1 Deep Water .............................................................................................. 136
17.13.2 Fish .......................................................................................................... 136
17.13.3 Temperature Upper .................................................................................. 136
17.13.4 Temperature Lower .................................................................................. 136
17.13.5 Temperature Rate .................................................................................... 136
SAVE SETTINGS TO USER C-CARD ................................................................. 137
LOAD SETTINGS FROM USER C-CARD ........................................................... 137
RESTORE CURRENT PRESET DEFAULTS ...................................................... 137
18. TROUBLESHOOTING .................................................................................................... 139
19. TECHNICAL TESTS ....................................................................................................... 141
19.0 SYSTEM TEST ..................................................................................................... 141
19.0.0 RAM Menu (reset) .................................................................................... 141
19.0.1 DIM Menu ................................................................................................. 141
19.0.2 Cartridges ................................................................................................. 142
19.0.3 Serial Ports .............................................................................................. 142
20. SPECIFICATIONS .......................................................................................................... 143
20.0 CP190i/CPF190i SPECIFICATIONS .................................................................... 143
20.1 CPF190i FISH FINDER SPECIFICATIONS ......................................................... 143
20.2 CP190i/CPF190i DIMENSIONS ........................................................................... 144
20.3 OPTIONAL FF525 FISH FINDER SPECIFICATIONS (use with CP190i) ........... 144
20.4 OPTIONAL WAAS GPS RECEIVER SPECIFICATIONS .................................... 145
CP190i and CPF190i
Page 11
21. APPENDIX: TERMS ....................................................................................................... 147
ANALYTICAL INDEX ............................................................................................................ 151
Page 12
CP190i and CPF190i
1. INTRODUCTION
Congratulations on your purchase of the Standard Horizon GPS Chart Plotter. Whether this
is your first Navigation device, or if you have other STANDARD HORIZON equipment,
STANDARD HORIZON organization is committed to ensuring your enjoyment of this
Navigation device. STANDARD HORIZON technical support personnel stand behind every
product we sell. Our Product Support team invites you to contact us should you require
technical advice or assistance, at 800/767-2450 or [email protected].
1.0
GENERAL INFORMATION
The CP190i (with internal GPS antenna) and CPF190i (with internal GPS antenna and Fish
Finder) are precision-crafted high-performance receivers for the Global Positioning System
(WAAS GPS) constellation of satellites that provide precise location data with a host of
navigation features and are ideal for nautical use and sealed against water ingress. The
CP190i and CPF190i are housed in rugged, impact-resistant cases with outstanding
ergonomic design for effortless operation. The CP190i and CPF190i are IP56 water resistent.
The advanced features of the GPS Chart Plotter/Fish Finder include:
&middot; Built-In Charts for coastal navigation of USA including Alaska, Hawaii and Great Lakes,
Canada, Bahamas, Caribbean, Cuba, Puerto Rico, and Central America
&middot; 5” 320x232 high resolution sunlight-readable display
&middot; Internal 50 channel WAAS GPS antenna
&middot; Optional connection for external 50 channels WAAS GPS antenna with 30 feet of cable
&middot; Dual chart window with independent zoom levels
&middot; CP190i: Fish Finder capable when the optional FF525 50/200kHz (Black Box Fish
Finder) are installed. Radar / AIS capable
&middot; CPF190i: Built-in Fish Finder. Radar and AIS capable
&middot; Selectable sailboat and power boat ship icons with red and green for port and starboard
&middot; Compass Rose indication around ship icon
&middot; Satellite images on base chart
&middot; Route Checking
&middot; Color Targets AIS
&middot; Dedicated AIS List page
&middot; Navigate to an Olympic Route
&middot; SOG Speed Filter function to resolve erratic speed redings in rough seas
&middot; Dedicated MARK, ROUTE and FIND keys
&middot; Supplied swivel mounting bracket and flush mounting hardware
&middot; CP190i: NMEA 0183 connections: 2 Inputs, 3 Outputs
&middot; CPF190i: NMEA 0183 connections: 1 Inputs, 2 Outputs
&middot; 3000 Marks / 50 Routes / 10000 Track Points
&middot; 3 year Waterproof Warranty
CPF190i: Fish Finder features:
&middot; 16/256 colors display user selectable
&middot; Built-in 600W Dual Frequency Fish Finder
&middot; 50 and 200kHz Frequency selection
CP190i and CPF190i
Page 13
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
2x and 4x Zoom
Bottom Lock and White Line selections
Sensitivity Time Control (STC) and Surface Noise Filter
Speed through water (if available on transducer)
Alarms - Shallow, Depth, Temp Upper and Lower
Temperature (if available on transducer)
1.1
PACKING LIST
When the package containing the Navigation device is first opened, please check for the
following contents. If any parts are missing contact the dealer this Navigation device was
purchased from.
Accessories and replacement parts may be ordered from STANDARD HORIZON’s Parts
Department at 741/827-7600 extension 6800 or e-mail at [email protected].
1.1.0
Packing List
PART CODE
ITEM
S8002224A
S8002225
S8002222
T9101553
S8002223
EM022U500
XUCMP0052
EM050U100
EM023U511
External bracket
Mounting knob with two washers
Dust cover
Power data cable
Flush mounting screws
Flush mount template
2 Amp fuse and holder
Owner’s Manual
Quick Reference Guide
1.2
OPTIONAL DOME OR OPEN ARRAY RADAR ANTENNAS
The Radar antennas are supplied by SI-TEX (631) 996-2690 in the USA and Canada. Refer
to the table below for compatible models:
MODEL NUMBER
DESCRIPTION
MDS-1
MDS-8
MDS-9
MDS-10-4
MDS-10-5
2kW 24 Mile 12.4” diameter Radome antenna
2kW 24 Mile 20” diameter Radome antenna
4kW 36 Mile 23.5” diameter Radome antenna
4kW 48 Mile 4FT Open Array
4kW 48 Mile 5FT Open Array
NOTE
For additional information, refer to the Radar Installation and Radar Operation Manuals located at
www.standardhorizon.com.
Page 14
CP190i and CPF190i
1.3
OPTIONAL ACCESSORIES
ACCESSORIES PARTS NAME
ITEM
Q7000619A
50 Channel GPS Antenna Unit GSU-5H Series UXOGSU51SD
FF525
50/200kHz Black Box Fish Finder (CP190i ONLY)
DST520
600W 2&quot; Nylon Thru-hull depth temp Transducer
DST521
600W Transom mount depth, speed temp Transducer
DST523
600W 2&quot; Bronze Thru-hull depth temp Transducer
DST525
600W In-hull Transducer
DST526
600W 2&quot; Bronze Thru-hull depth, speed temp Transducer
DST527
1000W In-hull depth Transducer (FF525 ONLY)
DST528A
1000W Bronze long stem depth temp Transducer (FF525 ONLY)
Dual
Freq
uenc
y Fish
Finde
r
CP190i and CPF190i
Page 15
Page 16
CP190i and CPF190i
2. INSTALLATION
NOTE
Throughout this Owner’s Manual same conventions are used. See the legend below:
[MENU]If you see brackets around a bold and capital letter word this refers to a key press.
GENERAL SETUP When a word(s) is bold capital letters and underlined, this refers to a menu
selection item.
A GPS Receiver and antenna are located inside the CP190i and CPF190i and are designed
to be bracket mounted. Both models may be flush mounted, however an optional external
GPS antenna may be needed to receive GPS satellite signals.
To use the external GPS antenna, the internal GPS antenna must be turned off, using the
procedure below:
1. Turn the CP190i and CPF190i On and select the GPS STATUS page.
2. Press [ENT] to show the GPS SETUP menu.
3. Move the ShuttlePoint knob to highlight INTERNAL GPS and press [ENT].
4. Move the ShuttlePoint knob to highlight OFF and press [ENT].
Off
On
INTERNAL GPS
RESTART GPS
NAVIGATION SPEED
NAVIGATION FILTER
High
DIFF CORRECTION SOURCE
WAAS/EGNOS
Figure 2 - GPS Setup menu
5. Press [CLR] to exit the GPS SETUP menu.
6. Confirm the GPS Status page is showing satellite signal strength bars and receive a fix.
2.0
MOUNTING THE GPS CHART PLOTTER
The CP190i and CPF190i are supplied with a swivel mounting bracket which allows them
to be dash mounted. When flush mounting, the optional GPS antenna may be needed to
receive GPS satellite signals. Refer to the images below for Bracket and Flush mounting.
NOTE
The CP190i and CPF190i are designed to be bracket and flush mounted. However when bracket
mounting the CP190i and CPF190i in an area where satellite reception is not possible with the
internal antenna or when flush mounted, the optional GPS antenna must be installed.
2.1
BRACKET MOUNTING
Before installing ensure the area the bracket is mounted to is strong enough to support the
weight of the GPS Chart Plotter especially while under way. After the location is found,
attach the mounting base to the area using the supplied hardware.
CP190i and CPF190i
Page 17
Figure 2.1 - Example of Bracket installation on CPF190i
2.2
FLUSH MOUNTING
The CP190i and CPF190i are supplied with a flush mount template for the cutout hole and
screw holes required to install the GPS Chart Plotter.
NOTE
Before drilling holes make sure there is enough room to mount the GPS Chart Plotter and there
are no obstructions.
Figure 2.2 - Example of Flush installation on CPF190i
Page 18
CP190i and CPF190i
1. After a location is found, peel the template label from the backing and apply the label
to the mounting area.
2. Drill a hole in one area of the cutout area that will allow the blade of a jig saw to be
inserted. Insert and cut out the area on the panel using the jig saw.
3. Next drill the four holes required to insert the GPS Chart Plotter with the mounting studs.
4. Install the mounting studs on the GPS Chart Plotter and insert into the mounting hole.
5. Attach the GPS Chart Plotter to the mounting location by attaching the supplied
hardware to the mounting studs.
2.3
MOUNTING THE OPTIONAL EXTERNAL GPS ANTENNA
An external WAAS GPS antenna is available when the CP190i or CPF190i is flush mounted
or mounted in an area where satellite reception is not possible with the internal antenna.This
antenna is designed to be mounted on a base, installed on an extension or flush mounted.
Choose a location for the antenna that has a clear view of the sky and is not located within
3Feet of a Radar or other transmitting antennas. Ensure there are no major obstructions or
fixtures in the immediate proximity to the antenna. The antenna relies on direct “line of sight”
satellite reception. If you are unsure of the chosen location, temporarily mount the antenna
in the desired location to verify correct operation. If mounted close to Radar, after the GPS
Chart Plotter has a fix, turn on the Radar to ensure the GPS Chart Plotter holds the fix (use
the GPS Status Page).
The thread used on the antenna is an industry standard (1inch 14TPI) used on a wide range
of mounting brackets.
NOTE
The antenna cable can be cut and spliced to ease installation. Care must be taken when
reconnecting the antenna cable to protect from water and corrosion.
2.3.0
Flush mounting the antenna
NOTE
Before drilling holes, it is recommended the antenna be positioned where the location is planned,
cable connected to the GPS Chart Plotter and power turned on to ensure a GPS Fix is received.
1.
2.
3.
4.
5.
6.
7.
Remove the threaded base from the antenna dome.
To ease installation a flush mounting template for the antenna has been included.
Apply the mounting template sticker to the area that was verified for GPS reception.
Then, drill out the 0.78” (20mm) and 0.13” (3.2mm) holes, and remove the template.
Insert the cable into the 0.78” (20mm) hole and route to the GPS Chart Plotter.
Apply a small amount or RTV to the underside of the antenna.
Place the antenna and then screw it into place using the screws.
NOTE
In some cases the screw may not be long enough. If this happens simply apply more RTV to the
underside of the antenna to glue it into place.
CP190i and CPF190i
Page 19
S8002348
Figure 2.3.0 - Installing the External GPS antenna (I)
3.2
” [&Oslash;
0.13
mm]
]
20 mm
0.78&quot; [&Oslash;
GPS OVERALL SHAPE
Figure 2.3.0a - Installing the External GPS antenna (II)
Smart GPS Cable
Pin
1
2
3
4
5
6
2.4
Wire Color
Red
Green
Brown
Black/Yellow
Description
Battery Positive
Smart GPS NMEA Input
Smart GPS NMEA Output
NC
NC
Battery Ground
CONNECTIONS
The CP190i and CPF190i have connectors that allow them to be connected to a Power
supply, optional WAAS GPS antenna, optional FF525 50/200kHz BLACK BOX FISH
FINDER (only for CP190i) and NMEA Devices* such as VHFs, AIS Receiver, Digital
Instruments and autopilots.
NOTE*
RS232 not opto-isolated electrical interface.
Page 20
CP190i and CPF190i
NOTE
The GPS Chart Plotter can send many sentences to external NMEA devices*. The NMEA Output
wires are yellow and white. If you have connected devices as shown in the table on the next page
and need to feed NMEA to other devices (Autopilot, RADAR…) you can parallel wires from the
yellow, brown or white wires to other devices.
2.4.0
CP190i Connection Table
Power Data Cable
Pin
1
2
3
4
5
Wire Color
Black
Red
Green
Blue
Brown
Description
Battery Ground
Battery Positive
NMEA Common
Port1 Input
Port1 Output
Connection Example
6
7
8
Grey
White
Yellow
Port2 Input
Port2 Output
Port3 Output
Additional Comments
Connect to Battery Ground
Connect to Battery Positive
Common (ground) for NMEA devices*
Connect to Output of NMEA devices*
Default is NMEA0183
Connect to Input of NMEA devices*
Default is NMEA0183 with GGA, GLL, RMC,
DBT, DPT, MTW, VHW and XTE sentences
Connect to FF520 or FF525
Default is Fish Finder
Connect to FF520 or FF525
Default is Fish Finder
Connect to Input of NMEA devices*
Default is NMEA0183 with APA, APB, BOD,
GGA, GLL, RMC and BOD sentences**
*NOTE
RS232 not opto-isolated electrical interface.
**NOTE: AUTOPILOT CONNECTION
Care must be taken when connecting the GPS Chart Plotter to an Autopilot. Normally Port
3 (Yellow wire) will be used to connect to an Autopilot input, however older autopilots may
not be able to read the sentences due to the talker ID that is being used (II Integrated
Instrument). If the Autopilot connections are made to Port3 (Yellow wire) and the Autopilot
is not reading the sentences, change the connections to Port1 (Brown wire) and change the
sentences to APA, APB, BOD, GGA, GLL, RMC and XTE.
2.4.1
CP190i Connections
2.4.1.0 DC Power Connection
Optional WAAS
GPS Antenna
CP190i
Red
Black
PWR &amp; ACC 1 Cable
CP190i and CPF190i
Switch
2A
Fuse
-
+
Battery
10-35Vdc
Page 21
2.4.1.1 Connection of the FF525, AIS Receiver, VHF and Autopilot
Optional WAAS
GPS Antenna
Red
Black
Switch
2A
Fuse
CP190i
Green
Blue
Brown
Gray
White
Yellow
-
+
Battery
10-35Vdc
NMEA Common
Port 1 Input
Port 1 Output
Port 2 Input
Port 2 Output
Port 3 Output
VHF
AIS
PILOT
PWR &amp; ACC 1 Cable
Optional WAAS
GPS Antenna
Tee
Red
Black
CP190i
Switch
2A
Fuse
Optional
Fish Finder
-
+
Battery
10-35Vdc
Green
Blue
Brown
Gray
White
NMEA Common
Port 1 Input
Port 1 Output
Port 2 Input
Port 2 Output
Yellow
Port 3 Output
AIS
Transducer
VHF
PWR &amp; ACC 1 Cable
NOTE
Port2 Input and Output is used by the optional FF525. In the diagram above you will notice Port2
Input and Output wires are shown in gray and not used.
2.4.1.2 AIS Setup
The CP190i has to be set up to be able to receive NMEA information from the AIS receiver.
The GPS Chart Plotter reads the AIS NMEA message VMD, type 1, 2, 3 and 5 for AIS Class
A and type 18, 19, 24 for AIS Class B. Select the used port and transmission speed by
following the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight IN/OUT CONNECTIONS and press [ENT] or
move the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight PORT1 INPUT and press [ENT] or move the
ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob up/down to select AIS 38400 and press [ENT] or move the
ShuttlePoint knob to the right.
NOTE
If an AIS receiver is not connected, Port1 Input can be connected to most DSC VHF’s for position
polling.
Page 22
CP190i and CPF190i
2.4.2
CPF190i Connection Table
Power Data Cable
Pin
1
2
3
4
5
Wire Color
Black
Red
Green
Blue
Brown
Description
Battery Ground
Battery Positive
NMEA Common
Port1 Input
Port1 Output
6
7
8
Grey
White
Yellow
NC
NC
Port 3 Output
Connection Example
Additional Comments
Connect to Battery Ground
Connect to Battery Positive
Common (ground) for NMEA devices*
Connect to Output of NMEA devices*
Default is NMEA0183
Connect to Input of NMEA devices*
Default is NMEA0183 with GGA, GLL, RMC,
DBT, DPT, MTW, VHW and XTE sentences
Connect to Input of NMEA devices*
Default is NMEA0183 with APA, APB, BOD,
GGA, GLL, RMC and XTE sentences**
*NOTE
RS232 not opto-isolated electrical interface.
**NOTE: AUTOPILOT CONNECTION
Care must be taken when connecting the GPS Chart Plotter to an Autopilot. Normally Port
3 (Yellow wire) will be used to connect to an Autopilot input, however older autopilots may
not be able to read the sentences due to the talker ID that is being used (II Integrated
Instrument). If the Autopilot connections are made to Port3 (Yellow wire) and the Autopilot
is not reading the sentences, change the connections to Port1 (Brown) and change the
sentences to APA, APB, BOD, GGA, GLL, RMC and XTE.
2.4.3
CPF190i Connections
2.4.3.0 DC Power Connection
Optional WAAS GPS
antenna
CPF190i
Red
Black
PWR &amp; ACC 1 Cable
Switch
2A
Fuse
-
+
Battery
10-35Vdc
Transducer
CP190i and CPF190i
Page 23
2.4.3.1 Connection of the AIS Receiver, VHF and Autopilot
Optional WAAS GPS
antenna
Red
Switch
Black
2A
Fuse
CPF190i
-
+
Battery
10-35Vdc
Green
Blue
NMEA Common
Port 1 Input
Yellow
Port 3 Output
AIS
VHF
PWR &amp; ACC 1 Cable
Transducer
Optional WAAS GPS
antenna
Red
Black
Switch
2A
Fuse
CPF190i
-
+
Battery
10-35Vdc
Green
Blue
Brown
NMEA Common
Port 1 Input
Port 1 Output
Yellow
Port 3 Output
VHF
PILOT
PWR &amp; ACC 1 Cable
Transducer
2.4.3.2 AIS Setup
The CP390i has to be set up to be able to receive NMEA information from the AIS receiver.
The GPS Chart Plotter reads the AIS NMEA message VMD, type 1, 2, 3 and 5. Select the
used port and transmission speed by following the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight IN/OUT CONNECTIONS and press [ENT] or
move the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight PORT1 INPUT and press [ENT] or move the
ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob up/down to select AIS 38400 and press [ENT] or move the
ShuttlePoint knob to the right.
NOTE
If an AIS receiver is not connected, Port1 Input can be connected to most DSC VHF’s for position polling.
NOTE
The Input and Output baud rate for each port is set using the Advanced Setup&gt;In/Out Connections
menu. For example if Port1 is set for AIS 38400, the Input and Output both operate at 38400 baud.
Page 24
CP190i and CPF190i
2.5
BATTERY CONNECTIONS
1. The GPS Chart Plotters are supplied with a fuse and holder. This fuse should be
installed into the Black wire to protect the NMEA Output/Input circuits from possible
damaged.
2. Connect the Red and Black wires from the GPS Chart Plotter to a 12VDC source as
directly as possible.
2.6
NMEA CONNECTIONS
The GPS Chart Plotter can be connected to external devices with NMEA and display
information. Examples:
&middot; DSC VHF Radio
&middot; Depth Sounder, Speed Log, Wind Instrument, Autopilot etc.
&middot; Radar (USA ONLY)
&middot; Personal Computer
&middot; AIS Receiver
&middot; MOBILARM System
2.7
GPS POSITION ON A VHF RADIO
STANDARD HORIZON has pioneered Digital Selective Calling (DSC) on VHF radios.
Advancements in DSC have made it possible to show the coordinates of a vessel that has
transmitted a DSC Distress Call or even Polled the location of another vessel and show
the position of that vessel on the display of STANDARD HORIZON VHFs.
STANDARD HORIZON has taken this feature one step further. If a CP190i or CPF190i is
connected to a DSC capable VHF, the vessel in Distress or the polled position of the vessel
is shown on the display of the GPS Chart Plotter, making it easy to navigate to the location
of the vessel. This is a great feature that could save someone’s life or for anyone wanting
to know the position of another vessel.
Other DSC VHF Manufactures
GPS Chart Plotter
Green
Brown
Blue
Description
NMEA Common Ground
NMEA Positive Output
NMEA Positive Input
VHF
Connect to NMEA Ground
Connect to NMEA Input
* Connect to NMEA Output (if available)
* Some manufacturers of DSC VHF’s are not capable of outputting NMEA DSC and DSE sentences to
the CP190i or CPF190i. Refer to the Owner’s Manual and confirm the VHF can output NMEA DSC
and DSE sentences.
NOTE
Refer to VHF Digital Selective Calling Section for operation.
2.8
CP190i: OPTIONAL BLACK BOX FISH FINDER
STANDARD HORIZON offers an optional BLACK BOX FISH FINDER called the FF525. Please
refer to the Owner's Manual supplied with the Fish Finder for connections and operation.
CP190i and CPF190i
Page 25
Dual
Frequ
ency
Fish
Finder
Figure 2.8 - FF525 50/200kHz BLACK BOX FISH FINDER
NOTE
The FF520 is also compatible.
2.9
RADAR ANTENNA (USA ONLY)
Please refer to Par. “1.3 Radar Unit supplied by SI-TEX USA”. The Radar antenna includes the
necessary electronics to deliver Radar information to a compatible STANDARD HORIZON
GPS Chart Plotter, and is supplied with mounting hardware kit, interconnection cable and
a Radar Junction Box.
Please refer to the Radar Installation Manual and Radar Operation Manual available at
www.standardhorizon.com.
2.10
PERSONAL COMPUTER CONNECTIONS
The GPS Chart Plotter can be connected to output Marks and Routes to many available PC
programs. To send or receive User Points the PC Program must be able to receive NMEA
WPL and RTE sentences. Refer to the table below for connection to a Serial DB9 connector.
Pin
2
3
5
PC DB9 connection
Receive
Transmit
Signal ground
Port 1 connection
Brown
Blue
Green
By default Port1 is set to receive or send User Points to and from a PC. The GPS Chart
Plotter may be set up to send and receive the User Points on a different Port using the
following procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight IN/OUT CONNECTIONS and press [ENT] or
move the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight SEND/REC RTE &amp; MARKS and press [ENT]
or move the ShuttlePoint knob to the right to show the popup window.
5. Move the ShuttlePoint knob to desired Port and press [ENT].
The PC COM settings are:
&middot; Baud Rate
: 4800
&middot; Parity
: None
&middot; Data Bits
:8
&middot; Stop Bits
:1
&middot; Flow Control : None
Page 26
CP190i and CPF190i
The format of the sentences that are sent:
&middot; MARK
$GPWPL,3249.061,N,00710.651,E,MRK002*22
&middot; WAYPOINT $GPWPL,3933.008,N,00639.969,E,WPT012*22
&middot; ROUTE
$GPWPL,2544.362,N,08011.672,W,WPT003*32
$GPWPL,2543.921,N,08011.481,W,WPT004*31
$GPWPL,2543.493,N,08011.768,W,WPT005*37
$GPRTE,2,1,c,ROUTE01,WPT003,WPT004,WPT005*21
2.11
NMEA DATA PAGE
The NMEA Data page is very useful to see if an external device (example: Depth Sounder)
is transmitting NMEA sentences to the GPS Chart Plotter. This page can also be used to
see if the GPS Chart Plotter NMEA Output is being loaded down by an external NMEA
device the GPS Chart Plotter is connected to. Example: A VHF radio is connected but the
radio is not receiving a GPS Position. Usually the VHF radio will be connected to the Green
and Brown wires. To check to see if the GPS Chart Plotter is transmitting the sentences:
1. Press [MENU], move the ShuttlePoint knob to highlight NMEA DISPLAY and press [ENT].
2. Move the ShuttlePoint knob to highlight DATA and press [ENT].
3. The NMEA DATA page is shown.
4. Connect the Blue Wire on the GPS Chart Plotter to the junction of the Brown wire and
the VHF wire. The display should look similar to the following picture.
Figure 2.11 - NMEA Data page
2.12
DEMO MODE (FOR DEALER USE)
In Demonstration Mode the GPS Chart Plotter automatically places a Destination point on
the Chart page and simulates navigation to the point. Also, the active page displayed on the
screen changes every 10 seconds. The pages are shown in the following order: Start-up
screen, GPS Status page, Chart/Compass tape page, Chart/Fish Finder page, Fish Finder
Full page, Radar page, Navigation page, Highway Page, Celestial page, NMEA Display
page.
NOTE
This mode is used by dealers to promote the features of the CP190i or CPF190i when on a retail
shelf.
The Demo mode can be selected from the Simulation Menu following the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move
CP190i and CPF190i
Page 27
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight SIMULATION and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight DEMO MODE and press [ENT] or move the
ShuttlePoint knob to the right to show the popup window.
5. Move the ShuttlePoint knob to select ON and press [ENT] or move the ShuttlePoint
knob to the right.
6. Demo mode is now activated.
Once the Demo Mode is enabled, it is possible to temporally exit Demo Mode by pressing
a key and return to the GPS Chart Plotter normal operation. If a key in not touched for 30
seconds the Demo Mode will re-start.
To disable the Demo Mode follow the procedure above selecting OFF at point 5.
Page 28
CP190i and CPF190i
3.
CONTROLS AND INDICATORS
NOTE
This section defines each control of the CP190i or CPF190i. For instructions, refer to Getting
Started and Advanced Settings sections of this Owner's Manual.
NOTE
Throughout this Owner’s Manual same conventions are used. See the legend below:
[MENU]If you see brackets around a bold and capital letter word this refers to a key press.
GENERAL SETUP When a word(s) is bold capital letters and underlined, this refers to a menu
selection item.
3.0
CONTROLS AND CONNECTIONS
The CP190i or CPF190i is controlled by using the keys located on the front panel. These
labeled keys are dedicated to specific functions. As you press a key, a single audio beep
confirms the key action; every time a key press is not valid, three rapid beeps sound to
indicate that the key action is not valid. There is also a ShuttlePoint knob to move the cursor
across the screen.
The ZOOM IN and ZOOM OUT keys
Pressing [ZOOM IN] shows more detail of a smaller area, by changing the chart scale and
zooming in on your display. Press [ZOOM OUT] to change the scale and show a wider,
otherwise less detailed view. Pressing and holding [ZOOM IN]/[ZOOM OUT] allows for
quick zoom, that is the fast change of the chart scale where only the land areas are drawn.
When [ZOOM IN]/[ZOOM OUT] is released all chart details are shown.
NOTE
The GPS Chart Plotter contains a Worldwide background that allows you to zoom in to 2NM. For
more detail, a C-MAP BY JEPPESEN NT+/MAX C-CARD must be purchased and installed.
The ShuttlePoint knob
The ShuttlePoint knob moves the cursor around the Chart Page (cursor mode) and
highlights menu items. It changes the GPS Chart Plotter from Home mode to Cursor mode
on the Chart Screen. For a detailed explanation of Cursor VS Home mode refer to Par. 3.1.1.
The ENT key
Press [ENT] to select the desired option or to confirm the selection.
The CLR key
When on the Chart Page, press [CLR] to set Home Mode, clear a selected function, leave
a menu, step backwards in a menu or exit a menu.
The MENU key
Selects the Main Menu. When in the Setup Menu mode, moving the ShuttlePoint knob to
the right enters a selection and moving the knob to the left clears the function.
Pressing and holding [MENU] for 3 seconds allows you to change the fields contained within
the data windows while on the Chart, Navigation, Highway, GPS Status or NMEA Display
page.
CP190i and CPF190i
Page 29
The GOTO key
This key is very useful when you desire to start navigating (goto) to a destination point. When
pressed, a popup window will be shown allowing you to select to start navigating to the a
Mark, a Route or the position of the cursor.
To stop navigation to a point, press [GOTO] and select Stop in the popup window.
The MARK key
This key places a Mark under the ship’s position when in Home Mode. When the cursor is
shown and [MARK] is pressed it will place a Mark under the location of the cursor.
The ROUTE key
When pressed places a Waypoint. Succeeding presses place more Waypoints to form a Route.
The PWR key (Backlight and Contrast)
Press and hold [PWR] to turn the GPS Chart Plotter On or Off. Once on, press [PWR] to
show and change the Contrast and Backlight settings.
The MOB key
When pressed the GPS Chart Plotter automatically places a Mark on the Chart Page under
the boat’s position to aid in the rescue or a person that may have fallen aboard. To stop
navigating, press [GOTO], select STOP and press [ENT].
The FIND key
A dedicated key that allows searching the optional C-MAP BY JEPPESEN NT+/MAX C-CARD
for Port Services, Ports, Tide Stations, Wrecks, Obstructions, Points Of Interest, Lakes
Information, Lakes By Name, User Points, GPS Coordinates or Information on any point on
the chart.
3.1
GETTING STARTED
The Getting Started section will take you through the frequently used operations and assist
you to customize the look of the GPS Chart Plotter.
3.1.0
Power On, Off and ShuttlePoint Knob operation
1. Press and hold [PWR] until the display shows the Start-Up page (see the following
picture). To turn Off, press and hold [PWR] until the display turns Off.
CPF190i
GPS Chart Plotter
Fish Finder
Software V16.30 00R
Figure 3.1.0 - Example of Start-Up page on CPF190i
2. When the power is first turned on two pages the Start-Up page and the Caution pages are
Page 30
CP190i and CPF190i
briefly shown before the GPS Status page.
WARNING
WARNING-LIMITATIONS ON USE
This product, including the C-MAP by Jeppesen charts, is intended to be used only as
an aid to navigation. It should facilitate use of official government charts, not replace
them. Only Official Government Charts and Notices to Mariners contain all the current
information needed for safe navigation. This product’s features cannot be relied on as
complete or accurate and may vary depending on location. It is the captain’s
responsibility to use official government charts, notices to mariners, caution, sound
judgment and proper navigational skills when operating their boat using this product.
This product contains a limited set of built-in C-MAP by
Jeppesen Charts.
This product supports C-MAP by Jeppesen electronic charts. Their use is subject to a
separate Jeppesen Data License Agreement which can also be found at
www.jeppesen.com, where users may also register to receive regular product safety
information.
Contact your dealer or Jeppesen for upgrade options.
Register with Jeppesen to receive
regular product safety information.
The built- in C-MAP by Jeppesen background charts of this product contain a limited
version of chart datasets only for general awareness.
Press ENTER to proceed.
By pressing ENTER, you confirm that you:
1. acknowledge the above warning and accept the limitations of this product and the
C-MAP by Jeppesen charts
2. have read the documentation for this product, including its notes, and the Jeppesen
Data License Agreement, and agree to be bound by the terms of the Jeppesen Data
License Agreement.
Figure 3.1.0a - Caution pages
NOTE
The Caution page on the left is shown only if the data C-CARD is over one year old.
IMPORTANT
The built-in C-MAP by Jeppesen charts are out-of-date, and may be
unsafe for navigation, which could place you and others at risk. You
are encouraged to contact your local dealer or Jeppesen to update
the built-in charts. Register with Jeppesen
(www.jeppesen.com) for real-time product updates and safety notices.
Press ENTER to proceed .
Figure 3.1.0b - Built-In Charts warning pages
3. When the GPS Chart Plotter is first turned on it will take some time for the GPS to acquire
a fix of your position. Look closely at the GPS Status page and you will see satellites and
relative signal strengths of each satellite. After a fix is received the GPS Chart Plotter
will automatically switch to the Chart Page with the ship icon centered on the screen.
1
WAAS
3D
2
1.2
1.5
3
20
11
25
31
1
Cursor
2 Ship
Icon
3 Cursor
window
Figure 3.1.0c - GPS Status and Chart pages
CP190i and CPF190i
Page 31
4. On the Chart page the ShuttlePoint knob is used to pan around the chart. Move the ShuttlePoint
knob to the left and you will notice a cross hair appears, this is called the cursor.
5. When you move the ShuttlePoint knob you will notice DST and BRG values in the Data
window change. This shows the Distance and Bearing from the GPS Fix of your vessel
to the position of the Cursor.
6. If the cursor is moved to the edge of the screen the GPS Chart Plotter will automatically
pan in the desired direction.
3.1.1
Cursor Vs. Home Mode
Cursor Mode
When the cursor is shown on the Chart Page, the chart plotter is in Cursor Mode.
In Cursor Mode the position of the vessel will not stay in the center of the page and will move
right off the edge of the screen (as your boat moves). Cursor Mode allows you to pan around
and look at areas on the chart. In this mode you can also create Marks, Routes, measure
distance and bearings from your current position.
Home Mode
When the ship icon is shown on the Chart Page (cursor is not shown) you are in Home
Mode. Now as the ship moves through the water the vessel’s position will be kept in the
center of the display.
NOTE
To change from Cursor Mode to Home Mode press [CLR].
3.1.2
Cursor and Menu selection speed
The CP190i and CPF190i allow you to control the speed the Cursor moves when the
ShuttlePoint knob is pressed. To change the speed:
Figure 3.1.2 - Cursor Speed menu
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight CURSOR SPEED and press [ENT] or move the
ShuttlePoint knob to the right.
4. The menu now shows two selections, Chart and Menu which allow the Cursor Speed
to be selected as High, Medium or Low on the Chart Page or within the menus.
Page 32
CP190i and CPF190i
5. With CHART or MENU selected, press [ENT] or move the ShuttlePoint knob to the right.
Move the ShuttlePoint knob to the desired setting and press [ENT] or move the
ShuttlePoint knob to the right.
6. Press [CLR] until the menu disappears or an easier method is to press the ShuttlePoint
knob to the left a few times.
7. Move the cursor on the Chart Page and see if the speed is to your liking.
3.1.3
Changing the Ship Icons
The cursor may be changed to any of the following. The default setting is Icon 6.
Icon 1
Icon 2
Icon 3
Icon 4
Icon 5
Icon 6
Icon 7
Figure 3.1.3 - Ship icons
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight SHIP ICON and press [ENT] or move the
ShuttlePoint knob to the right to show the popup window with ship icons.
4. Move the ShuttlePoint knob to select the desired icon and press [ENT] or move the
ShuttlePoint knob to the right to select a new icon.
5. Press [CLR] or move the ShuttlePoint knob to the left to exit the menu and show the
Chart Page.
3.1.4
Changing the Backlight and Contrast
With the CP190i and CPF190i turned on, briefly press [PWR] to show the backlight and
contrast popup window. Move the ShuttlePoint knob to the left or right to adjust the LCD
backlight intensity or up or down to change the LCD contrast. Press [ENT] to set.
Figure 3.1.4 - Backlight and Contrast adjustment
3.1.5
Selecting North Up or Course Up
The default selection is COURSE UP: the top of the Chart page oriented so it will always
show the area ahead of the direction your vessel is travelling.
CP190i and CPF190i
Page 33
Figure 3.1.5 - Course Up/North Up menu
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight COURSE UP/NORTH UP and press [ENT] or
move the ShuttlePoint knob to the right.
4. Another popup window will be shown with NORTH UP and COURSE UP, move the
ShuttlePoint knob to the desired selection and press [ENT] or move the ShuttlePoint
knob to the right.
5. Press [CLR] or move the ShuttlePoint knob to the left to exit the menu and show the
Chart page.
NOTE
When the CP190i and CPF190i are in Course Up mode a small arrow icon
Chart page indicating North.
3.2
will be shown on the
AUTOMATIC TIME
The time information supplied by the GPS satellites is in Universal Time Coordinates (UTC or
Greenwich England Mean Time). To change the GPS Chart Plotter to read the correct time, first
you must figure out the offset and if it is Daylight Savings Time. For example on the West coast of
the United States or Pacific Standard Time the offset needed would be –08:00 or –07:00 for Daylight
Savings Time, Eastern Standard Time –05:00 or –04:00 for Daylight Savings Time.
Figure 3.2 - Adjusting Time
Page 34
CP190i and CPF190i
The Time Setup menu allows you to enter a time zone offset for your location, selection to
automatically adjust the time for daylight savings and to configure the time in 12 or 24 hour
formats.
Figure 3.2a - Time Setup menu
NOTE
By setting the time in the steps below, the time shown on the Celestial page is automatically set up.
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight TIME SETUP and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight TIME ZONE and press [ENT] or move the
ShuttlePoint knob to the right.
5. Look at the table and find the time zone for your area. Move the ShuttlePoint knob up
or down to select the desired zone and press [ENT].
6. Next move the ShuttlePoint knob to highlight DAYLIGHT SAVING and press [ENT] or
move the ShuttlePoint knob to the right.
7. Daylight Saving menu has 3 options:
7.1 OFF
Select Off when your location does not recognize Daylight Savings Time;
7.2 ON
Select On to manually turn Daylight Savings Time On. This is the default
selection;
7.3 AUTO When selected the Daylight Savings Time offset is automatically changed.
8. Press [CLR] or move the ShuttlePoint knob to the left until the Chart Page is shown.
3.3
SELECTING LORAN TD OR OTHER COORDINATE SYSTEM
The GPS Fix coordinates can be changed to show Latitude/Longitude, Loran TDs or UTM.
Below is the window that will appear when customizing the Coordinate System.
CHART DATUM
CHART ORIENTATION RES
Figure 3.3 - Coordinate System menu
CP190i and CPF190i
Page 35
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight NAVIGATE and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight COORDINATE SYSTEM and press [ENT] or
move the ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob to highlight the desired coordinate type and press [ENT] or
move the ShuttlePoint knob to the right.
6. Press [CLR] or move the ShuttlePoint knob to the left until the Chart page is shown.
NOTE
If the TD is selected, you should set the Chain, Pair, ASF1, ASF2 and Alter. If the TD numbers are
not correct the Pair letters may be backwards. Reversing the two letters usually solves this issue.
Example: Y/Z change to Z/Y.
3.4
CHANGING THE CHART COLOR
The CP190i and CPF190i have preprogrammed settings allowing you to customize the look
of the Chart page. The default is Sunlight, however there are other settings: Classic, NOAA,
Night and Normal. Night is very useful during evening hours so not to impair night vision.
Figure 3.4 - Display Color menu
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight DISPLAY COLOR and press [ENT] or move the
ShuttlePoint knob to the right.
4. A popup window will be shown with Normal, Classic, NOAA, Night and Sunlight. Move
the ShuttlePoint knob to the desired selection and press [ENT] or move the ShuttlePoint
knob to the right.
5. Press [CLR] or move the ShuttlePoint knob to the left to exit the menu and show the
Chart page.
3.5
SELECTING LANGUAGE
To ease operation in different countries, the software includes translation and display of the
following 16 Languages:
Page 36
CP190i and CPF190i
&middot; English
&middot; Italian
&middot; French
&middot; German
&middot; Spanish
&middot; Norwegian
&middot; Swedish
&middot; Portuguese
&middot; Chinese (Traditional)
&middot; Danish
&middot; Dutch
&middot; Greek
&middot; Finnish
&middot; Russian
&middot; Chinese (Simplified)
&middot; Japanese
The translations are included in Menu descriptions and on Info Functions to ease operation.
See also Par. 6.0.7. Set the language to be displayed on menus, data pages, warning/alarm
messages, full/quick info, list of objects found by find/nearest function, and on charts (such
as place’s names and buoy’s names and so on). The selection now includes the capability
to display languages in non-Latin characters (UNICODE format).
To select the language you want:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight LANGUAGE and press [ENT] or move the
ShuttlePoint knob to the right.
4. Another popup window will be shown with the available languages, move the ShuttlePoint knob to the desired language and press [ENT] or move the ShuttlePoint knob to
the right.
5. Press [CLR] or move the ShuttlePoint knob to the left to exit the menu and show the
Chart page.
CHAR
Figure 3.5 - Language Selection menu
NOTE
If the selected language is not available on cartographic data, English is used.
WARNING
If you have accidentally selected a language and are unable to return to the Language Selection
menu, perform the following procedure:
a. Select the Chart page.
b. Press [MENU] two times, move the Shuttlepoint knob to highlight the first (top) selection in the
menu and press [ENT].
c. Move the Shuttlepoint knob to highlight the LANGUAGE item and press [ENT].
d. A language window will be shown, select your language and press [ENT].
CP190i and CPF190i
Page 37
3.6
SETTINGS IN GENERAL SETUP MENU
The GENERAL SETUP menu has other selections that allow you to customize the display.
All selections are listed below:
TIME SETUP
Select the Time Zone offset, enable or disable Daylight Savings time and select the
Time Format and switch between 12 or 24 hours time format.
DATE FORMAT
Select the Date format among MM-DD-YY (default), DD-MM-YY or YY-MM-DD.
COURSE UP/NORTH UP
Select North Up (the top of the page is fixed to North) or Course Up (the top of the page
is orientated to the direction the vessel is heading. This is the default).
KEYPAD BEEP
Allows the beep produced when a key is pressed to be turned On (default) or Off.
UNITS OF MEASURE
Units of Measure can be selected for Distance*, Speed, Depth, Altitude and Temperature.
NAV AIDS PRESENTATION Allows the Nav Aids presentation to be drawn using NOAA symbology when US (default)
is selected or International symbols when International is selected. When selected these
functions affect how the icons for Lights, Signals, Buoys and Beacons are displayed.
DISPLAY COLOR
Changes the background colors of the chart page to enhance the visibility of the screen
depending on the surrounding light conditions. Normal is recommended when the GPS
Chart Plotter is not exposed to the direct sunlight. When this mode is set the charts are
displayed in order to use colors as similar as possible to ones used in the original paper
charts. Classic uses vivid chart colors presentation. NOAA allows setting NOAA paper
chart colors presentation. Night is recommended when the environment is dark in order
to reduce the glare of the display. The GPS Chart Plotter displays charts and screen in
darker colors. SunLight (default) is designed to enhance the visibility of the screen when
the GPS Chart Plotter is exposed to sunlight. The charts are much brighter than in the
other modes and the depth areas are filled with the white color so different depth areas
are not easily distinguishable.
SHIP ICON
Select from a variety of ship icons that represent your vessels position on the Chart Page.
The default is Icon 6.
COMPASS ROSE
Allows selection of compass direction indication around ship icon. The default is On.
CURSOR SPEED
MEASURE DISTANCE
START point
WINDOWS SETUP
Page 38
Selects the speed among Low, Medium (default) and High for the cursor in the CHART
page and within the MENU.
When this function is On, and the ShuttlePoint knob is moved to a location where you want
to start measuring a distance and press [ENT]. Move the ShuttlePoint knob to move the
cursor to a second location where you want to finish measuring a distance and press
[ENT]. A line will appear between the Start and Finish points and a popup window will be
shown indicating the distance and bearing from the Start and Finish points. Press [ENT]
to delete both points. (Off is the default).
Finish point
This menu selection allows the data windows to be customized on the CHART PAGE and
NAVIGATION PAGE (refer to section 12.0.0).
CP190i and CPF190i
LANGUAGE
AUTO INFO
Allows changing the language for menus and data screens.
When the cursor is moved over a buoy, Mark or other item a popup window will show
information of the item. This menu item allows the window to be turned Off, On Points
(default) or On All.
Auto Info ON POINTS
Auto Info OFF
CURSOR WINDOW
By default when the cursor is moved a window is shown with the Lat/Lon Distance and
Bearing from the vessels location to the cursor. This selection allows the window to be
turned On (default) or Off. The Cursor Window is automatically disabled when General
is set in Windows Setup option.
Cursor Window OFF
Cursor Window ON
CURSOR POSITION
COG TIME LINE
Auto Info ON ALL
The position of the cursor can be customized so it is centered in the middle (if Center
selected) or centered on the bottom of the Chart page (if Bottom selected, default).
It is a line projected from the ship icon which indicates the distance your vessel will travel
at the current speed. Selections are 2, 10 (default), 30 minutes, 1, 2 hours and infinite.
NOTE*
The available Units of Measure for Distance are: Nm, Sm, Km, Nm+Ft, Nm+m. Note when “Nm+Ft”
is selected if the distance is less than 1.0 Nm, it turns to Feet. When “Nm+m” is selected if the
distance is less than 1.0 Nm, it turns to Meters.
3.7
ABOUT PAGE
From Main Menu page it is possible to select the About page containing Software, Chart and
optional devices information.
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight About... and press [ENT] or move the
ShuttlePoint knob to the right.
3. The Information page appears on the screen (see the following picture).
CP190i and CPF190i
Page 39
1 Software System Information
XXXXXX
YY.YY
1
2 Cartography Information
INTCHART 1
: WW-M012.03 MARINE FRESHWATER WWBK
BUILT-IN CHARTS: NA-Z010.00
: M-NA-M632.00 L. ANGELES and S. PEDRO BAYS
2
3
Designed for
3 Storage Capacity
Figure 3.7 - Example of About page
4. Press [CLR] or move the ShuttlePoint knob to the left to exit and show the Chart Page.
Page 40
CP190i and CPF190i
4.
4.0
FIND SERVICES
USING FIND SERVICES &amp; MORE FUNCTIONS
The CP190i and CPF190i have a dedicated [FIND] key that allows searching the optional
C-MAP BY JEPPESEN NT+/MAX C-CARD for Port Services, Ports, Tide Stations, Wrecks,
Obstructions, Points Of Interest, Lakes, User Points, GPS Coordinates or Information on
any point on the Chart.
4.0.0
Port Services
This feature is used to locate Port Services nearest the position of your vessel.
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight PORT SERVICES and press [ENT] or move the
ShuttlePoint knob to the right.
3. A popup window will be shown with a list of different Port Services. The table below
shows a list of the available Port Services:
Figure 4.0.0 - Port Services Table
4. Move the ShuttlePoint knob to highlight the desired type of service and press [ENT].
5. Another popup window will appear displaying the distance and position of the services
closest to your location.
6. Using the ShuttlePoint knob, highlight the desired service and press [ENT]. This will
show information about the service.
7. Press [CLR] to show the actual position of the service on the Chart Page.
8. Press [CLR] again at any time to return your cursor to your vessel’s position.
CP190i and CPF190i
Page 41
WAAS 3D
WAAS 3D
Figure 4.0.0 - Find Port Services
4.0.1
Port
This feature is used to locate the 10 nearest Ports to the position of your vessel.
A Port is represented with a
on the Chart Page.
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight PORT and press [ENT] or move the ShuttlePoint knob to the right.
3. A popup window will be shown with a list of nearest Ports.
4. Move the ShuttlePoint knob to highlight the desired Port and press [ENT].
5. Another window will appear displaying the details of the selected Port.
6. Press [CLR] to show the actual position of the Port on the Chart Page.
7. Press [CLR] again at any time to return your cursor to your vessel’s position.
WAAS 3D
Figure 4.0.1 - Find Port
4.0.2
Tide Stations
This feature is used to locate the 10 nearest Tide Stations to the position of your vessel.
Once a Tide Station is selected the Tide Graph can be used to determine Tide height and
draught of the Tide based on a user-specified time.
A Tide Station is represented with a
on the Chart Page.
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight TIDE STATIONS and press [ENT] or move the
ShuttlePoint knob to the right.
3. A popup window will be shown with a list of nearest Tide Stations.
4. Move the ShuttlePoint knob to highlight the desired Tide Station and press [ENT].
Page 42
CP190i and CPF190i
5. Another window will be shown detailing the selected Tide Station information.
6. Press [CLR] to show the actual position of the Tide Station on the Chart Page.
7. Press [CLR] again at any time to return your cursor to your vessel’s position.
WAAS 3D
Figure 4.0.2 - Find Tide Stations
1
2
3
Figure 4.0.2a - Tide Graph page
Refer to the image above. The time (3) displayed corresponds to the location of the crosshair cursor (2) in the Tide Graph (1). Moving the ShuttlePoint knob to the left or right changes
the time, and moving the ShuttlePoint knob up or down selects the Tide height and Tide
draught on the Tide Graph.
NOTE
The Local Offset matchs the Time Offset entered in the Time Setup menu (see Par. 3.2)
4.0.3
Wrecks
This feature is used to locate the 10 nearest Wrecks to the position of your vessel. A Wreck
is represented with an icon on the chart. See the following table:
ICON
DESCRIPTION
non-dangerous wreck
dangerous wreck
#
F o u l
Masts
distributed remains of wreck
wreck showing mast/masts
wreck showing any portion of hull or superstructure
Figure 4.0.3 - Wreck icons Table
CP190i and CPF190i
Page 43
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight WRECKS and press [ENT] or move the
ShuttlePoint knob to the right.
3. A popup window will be shown with a list of nearest Wrecks.
4. Move the ShuttlePoint knob to highlight the desired Wreck and press [ENT].
5. Another window will be shown detailing the Wreck information.
6. Press [CLR] to show the actual position of the Wreck on the Chart Page.
7. Press [CLR] again at any time to return your cursor to your vessel’s position.
WAAS 3D
Figure 4.0.3a - Find Wrecks
4.0.4
Obstructions
This feature is used to locate the 10 nearest Obstructions to the position of your vessel.
An Obstruction is represented with an icon on the chart, see the following table:
ICON
Obstn
Mast (1- 2 )
Wk
DESCRIPTION
snag/stump
wellhead
diffuser
#
crib
#
fish haven
foul area
#
F o u l
foul ground
ice boom
46 Obstn
ground tackle
Figure 4.0.4 - Obstruction icons Table
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight OBSTRUCTIONS and press [ENT] or move the
ShuttlePoint knob to the right.
3. A popup window will be shown with a list of nearest Obstructions.
4. Move the ShuttlePoint knob to highlight the desired Obstruction and press [ENT].
5. Another window will be shown detailing the Obstruction information.
6. Press [CLR] to show the actual position of the Obstruction on the Chart Page.
7. Press [CLR] again at any time to return your cursor to your vessel’s position.
Page 44
CP190i and CPF190i
WAAS 3D
Figure 4.0.4a - Find Obstructions
4.0.5
Lakes Information
This feature is used to find information on the 10 closest Lakes near the position of your
vessel.
A Lake Info is represented with a
on the Chart page.
NOTE
An optional MAX Lake CARD must be inserted into the GPS Chart Plotter to take advantage Lakes
Information. The available MAX Lake CARDs are: NA-M017 USA: North; NA-M018 USA:
East;NA-M019 USA: South; NA-M020 USA: West; NA-M029: Alaska; NA-M048: Canada.
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight LAKES INFORMATION and press [ENT] or
move the ShuttlePoint knob to the right.
3. A popup window will be shown with a list of Outdoor Recreational Area objects.
4. Move the ShuttlePoint knob to highlight the desired object and press [ENT].
5. Another popup window will appear displaying the distance and position of the Lakes
closest to your location.
6. Using the ShuttlePoint knob, highlight the desired Lake and press [ENT]. This will show
information on the Lake.
7. Press [CLR] to show the actual position of the Lake on the Chart Page.
8. Press [CLR] twice to return your cursor to your vessels position.
WAAS 3D
WAAS 3D
INFORMATION
Figure 4.0.5 - Find Lakes Information
4.0.5.0 Quick Info On Lakes
Upon viewing the chart of a lake, you can click on the Lake Info icon to query the available
information immediately displayed with many details. For example, see the following picture:
CP190i and CPF190i
Page 45
Figure 4.0.5.0 - Example of Lakes info
When the cursor is placed over the icon, the icons of the available services are shown:
Figure 4.0.5.0a - Quick Info: available services
If you press [ENT] all available information about the cartographic point under the cursor
will be shown. See the next paragraph.
4.0.5.1 Full Info On Lakes
The following is an example of Full Info on Lakes:
Figure 4.0.5.1 - Example of Full Info page
To see the &quot;Fishing&quot; object press [MENU] (when the &quot;Fishing&quot; object is highlighted). On the
screen appears:
Page 46
CP190i and CPF190i
Figure 4.0.5.1a - Example of picture associated to the Fishing object
4.0.6
Lakes By Name
This feature is used to locate Lakes By Name nearest the position of your vessel.
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight LAKES BY NAME and press [ENT] or move
the ShuttlePoint knob to the right.
3. A popup window will be shown with a list of nearest Lakes.
WAAS 3D
INFORMATION
Figure 4.0.6 - Find Lakes By Name
4. Move the ShuttlePoint knob to highlight the desired Lake. Otherwise press [MENU] to
enter the desired Lake name. A window will be shown: move the ShuttlePoint knob to
highlight the edit of Lake name and press [ENT] to accept: another popup window will
appear displaying the distance and position of the Lake.
5. Press [ENT] to show the actual position of the Lake on the Chart Page.
6. Press [CLR] twice to return your cursor to your vessel’s position.
4.0.7
Points Of Interest
This feature is used to locate Points Of Interest nearest the position of your vessel.
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight POINTS OF INTEREST and press [ENT] or
move the ShuttlePoint knob to the right.
3. A (Category) popup window will be shown with a list of Category types (i.e. attractions,
emergency, entertainment).
4. Move the ShuttlePoint knob to highlight the desired Category and press [ENT].
5. A (Type) popup window will be shown with a list of types.
6. Move the ShuttlePoint knob to highlight the desired Type and press [ENT].
7. A popup window will be shown with a list of nearest Points Of Interest that fall into the
Category and Type you have selected.
CP190i and CPF190i
Page 47
8. Move the ShuttlePoint knob up/down to highlight the desired Point Of Interest and press [ENT].
9. Another window will be shown with detailing the Point Of Interest information.
10. Press [CLR] to show the actual position of the Point Of Interest on the Chart Page.
11. Press [CLR] again at any time to return your cursor to your vessel’s position.
WAAS 3D
WAAS 3D
INFORI
Figure 4.0.7 - Find Points Of Interest
4.0.8
User Points
This feature is used to search for User Points (Marks and Waypoints you have created
and stored) by name quickly and efficiently.
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight USER POINTS and press [ENT] or move the
ShuttlePoint knob to the right.
3. The (Select Name) popup window will appear. This window will allow you to enter in the
name of the User Point you wish to locate.
4. Move the ShuttlePoint knob up/down to change each number or letter and left/right to
move to the next or previous position in the name of the Mark.
5. Once the name of the desired Mark reads in the (Select Name) window, press [ENT]
to show the location the Mark on the Chart Page.
6. Press [CLR] at any time to return your cursor to your vessel’s position.
WAAS 3D
INFORM
Figure 4.0.8 - Find User Points (Marks and Waypoints)
4.0.9
Coordinates
This feature allows you to enter Coordinates (Latitude/Longitude) and view the entered
position on the Chart Page.
Page 48
CP190i and CPF190i
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight COORDINATES and press [ENT] or move the
ShuttlePoint knob to the right.
3. A (Coordinate) popup window will be shown to allow you to enter in a specified Latitude
and Longitude.
4. Move the ShuttlePoint knob up/down to change each number or letter and left/right to
move to the next or previous position in the Coordinates.
5. Once the Coordinates are entered, press [ENT] to show the location the Mark on the
Chart Page.
6. Press [CLR] at any time to return your cursor to your vessel’s position.
WAAS 3D
INFORMATION
Figure 4.0.9 - Find GPS Coordinates
4.0.10 Information
This feature allows you to obtain information on any position on the Chart page.
1. Press [FIND].
2. Move the ShuttlePoint knob to highlight INFORMATION and press [ENT] or move the
ShuttlePoint knob to the right.
3. A page will be shown with objects information. The upper side of the page contains the
Info Tree and the lower side contains the expanded information. While moving the
ShuttlePoint knob through the Info Tree, all the relevant information of the selected
object is shown on the lower part of the page.
4. Press [CLR] again at any time to return your cursor to your vessel’s position.
Figure 4.0.10 - Find Information
CP190i and CPF190i
Page 49
Page 50
CP190i and CPF190i
5.
MAX CARTOGRAPHY OVERVIEW
5.0
BUILT-IN CHARTS
5.0.0
Coverage areas and details
Figure 5.0.1 - Coverage Area
The CP190i and CPF190i have Built-In Charts for coastal navigation of USA including
Alaska, Hawaii and Great Lakes, Canada, Bahamas, Caribbean, Cuba, Puerto Rico, and
Central America which include:
a. Depth contours and spot soundings to 66 feet (20 meter) on lower scale charts and 33
feet (10 meters) on higher scale charts
b. All nav-aids with icon
c. Tidal diamond symbols on Chart Page
1. Marina symbol with name and the list of services symbols
5.0.1
Updating Built-In Charts
The Built-In Charts can be updated by purchasing a Chart Update Card from your local
marine electronics dealer or C-MAP USA at (800) 424-2627.
This Chart Update Card may be used ONE time to update the charts in a GPS Chart Plotter.
After the updating, the Chart Update Card will not update other GPS Chart Plotters.
After purchasing the Chart Update Card, follow the procedure below to update the charts.
CP190i and CPF190i
Page 51
1.
2.
3.
4.
Turn Off the GPS Chart Plotter.
Insert the Chart Update Card into the slot.
Press and hold [PWR] to turn the GPS Chart Plotter On.
The GPS Chart Plotter’s display will show a message that the Built-In Charts are being
uploaded.
5. After uploading the GPS Chart Plotter will check to ensure the charts have been loaded
correctly and show a message.
NOTE
If the message shows the charts were not updated correctly, follow steps 1-4 again. If the GPS
Chart Plotter shows a error message again, contact C-MAP USA at (800) 424-2627 for assistance.
5.1
INSERTING THE OPTIONAL MAX C-CARD
Hold the C-CARD by the long inclined side so that you can see the C-MAP BY JEPPESEN label.
Figure 5.1 - Inserting C-CARD
Open the door, gently push the C-CARD into the slot: push the C-CARD in as far as it will
go, then close the door.
ser.n
ser.n
e
code dat
e
code dat
class
class
Figure 5.1a - Inserting C-CARD (details)
NOTE
The small connector below the C-CARD is only used by Standard Horizon repair technicians.
Page 52
CP190i and CPF190i
Key points are:
Data Features
&middot; ISO Certification (electronic chart production process with quality certification)
&middot; Extra Large Coverage (all the C-Map electronic chart detail and a huge coverage
without having to change cartridge)
&middot; Official data source (data based on use of official data sources Hydrographic Offices
Release)
&middot; Detailed World Background (worldwide background chart with details)
&middot; Depths &amp; Land Elevation (color shading of sea depth and land altitude for improved
chart appearance)
&middot; Bathymetric &amp; Spot Soundings (Data Base with depth and bathy information for an
extraordinary view of the seabed depth)
&middot; Detailed Port Plan to information (complete port and marina charts with detail)
&middot; Search &amp; Find (quickly locates chart contents and objects)
&middot; Tides Preview (allows viewing of current, future and past tide cycles of specific NOAA
Tide Stations)
&middot; Dynamic Currents (current arrows showing speed and direction of current, future and
past currents)
&middot; Dynamic Nav-Aids (selection to enable the Nav-Aids to blink to their specifications
and appear on the chart in color)
&middot; Port Info (searchable data base of service in ports)
&middot; Enhanced Port Info &amp; Roads (searchable data base of detailed information that
include facilities and services in ports and surrounding areas)
&middot; Object Info (moving cursor over object to show restricted area details and related
information)
&middot; Quick Info (moving cursor over wrecks, shoals, Nav-Aids to show restricted area
details and related information and object to show details)
&middot; Photos &amp; Diagrams (high definition pictures of ports, piers, bridge diagrams and navaids)
&middot; Multilanguage Support (allows the plotter to show language of your choice in using
proper character set for Asian and other countries)
&middot; True-Type Font (improves text on chart for optimal reading)
Presentation Features
&middot; Clear View (advanced legibility techniques providing more chart data on the screen)
&middot; Clear Info (sophisticated &quot;Human Dictionary&quot; to translate Nav-Aid abbreviations found
on paper charts)
&middot; Flexi-Zoom (increased Under and Over Zoom between chart levels, resulting in
optimal scale display for any situation)
&middot; Perspective View (&quot;Real World&quot; perspective view of the chart, updated real-time
during navigation)
&middot; Enhanced Mixing Levels (seamless data presentation)
&middot; Off-line redraw (cartography level transition without image construction)
Cartographic Data related Features
&middot; Guardian Alarm (the Guardian Alarm is a user defined area in front of your vessel to
alert you while navigating of possible obstacles on the chart)
&middot; Safety Status Bar (a status bar with six boxes to show the status of certain functions.
Any warning or alarm condition is identified by the red color to indicate possible risk)
CP190i and CPF190i
Page 53
&middot; Safety Route Check (sophisticated function that checks for dangerous objects along
your navigation route)
MAX and NT/NT+ C-CARD coexistence
&middot; When NT+ data and MAX data cover different areas, the GPS Chart Plotter receives
data from both charts (depending on the current position).
&middot; When NT+ data and MAX data cover the same area, the GPS Chart Plotter receives
data only from MAX chart.
Page 54
CP190i and CPF190i
6.
6.0
MAP FUNCTIONS
MAX FUNCTIONS MENU
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right. The MAX Functions menu appears on the screen:
Figure 6.0 - Max Functions Menu
The available Max Functions menu is described in the following.
6.0.0
Zoom Type
Zoom Type refers to the chart scale selection. It has two options: Standard (default) or FlexiZoom. When Zoom Type is set to Flexi-Zoom, a short [ZOOM IN]/[ZOOM OUT] push
causes a change of chart level, while a long [ZOOM IN]/[ZOOM OUT] push (press and hold)
causes an expansion or compression of the chart image, without a chart level change.
CHART: US,NOS,GRAPH,11472H
SCALE: 1:40000
ACQUIRING
SH
CHART: US,NOS,GRAPH,11472H
SCALE: 1:40000
G
ON
PU
L
ACQUIRING
CHART: US,NOS,GRAPH,11474
SCALE: 1:80000
ACQUIRING
SH
OR
TP
US
H
Figure 6.0.0 - Zoom Type
CP190i and CPF190i
Page 55
Note that in the top of the previous picture the chart scale remains the same but it is
graphically compressed.
By pressing [ZOOM IN]/[ZOOM OUT] a popup window is displayed on a corner of the chart
screen. The window shows the current zoom factor: Normal is the original chart level (1:1
scale), Over-Zoom x2, x4, x16, x32, Under-Zoom x1/2, x1/4.
To activate this function follow the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight ZOOM TYPE and press [ENT] or move the
ShuttlePoint knob to the right.
4. The menu now shows two selections, STANDARD or FLEXI-ZOOM.
5. Move the ShuttlePoint knob to select the selection and press [ENT].
6. Press [CLR] until the menu disappears or an easier method is to move the ShuttlePoint
knob to the left a few times.
6.0.1
Icon Size
On MAX charts it is possible to set the size of all icons drawn on the charts, selecting
between Standard (default) and Large size.
ICONS SIZE standard
ICONS SIZE large
Figure 6.0.1 - Icons Size
To activate this function follow the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight ICONS SIZE and press [ENT] or move the
ShuttlePoint knob to the right.
4. The menu now shows two selections, STANDARD or LARGE.
5. Move the ShuttlePoint knob to select the selection and press [ENT].
6. Press [CLR] until the menu disappears or an easier method is to move the ShuttlePoint
knob to the left a few times.
6.0.2
Place Name Size
On MAX charts it is possible to set the size of all names drawn on the charts, selecting
between Standard (default), Medium and Large size.
Page 56
CP190i and CPF190i
PLACE NAMES SIZE standard
PLACE NAMES SIZE large
PLACE NAMES SIZE medium
Figure 6.0.2 - Place Names Size
To activate this function follow the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight PLACE NAMES SIZE and press [ENT] or move
the ShuttlePoint knob to the right.
4. The menu now shows three selections, STANDARD, MEDIUM or LARGE.
5. Move the ShuttlePoint knob to select the selection and press [ENT].
6. Press [CLR] until the menu disappears or an easier method is to move the ShuttlePoint
knob to the left a few times.
6.0.3
Perspective View
The Chart page may be show in a perspective (fly over) or normal mode during navigation.
Perspective view of the chart is a type of “bird’s eye” view of a chart, and give you a more
realistic perspective of the chart. As the upper side of the chart is more compressed than
the lower side, a wider chart area is visible, so it allows showing more chart information
immediately ahead and around the cursor.
Perspective View ON
Perspective View OFF
Figure 6.0.3 - Perspective View
To activate this function follow the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight PERSPECTIVE VIEW and press [ENT] or
move the ShuttlePoint knob to the right.
4. The menu now shows two selections, ON or OFF.
5. Move the ShuttlePoint knob to select the selection and press [ENT].
6. Press [CLR] until the menu disappears or an easier method is to move the ShuttlePoint
knob to the left until the Chart Page is shown.
CP190i and CPF190i
Page 57
6.0.4
Dynamic Nav-Aids
This function allows the blinking of the Nav-Aids to be turned On or Off. The blink period and
color of each Nav-aid is read from the Nav-Aid attributes stored on the optional C-MAP BY
JEPPESEN C-CARD. When the ship is inside the Nav-Aid nominal range, the light of the NavAid will start blinking. When Dynamic Nav-Aids option is set to On, when the flashing light
is Off, or when fix position is out of the sector, the light color is displayed by using a faint light
color.
To activate this function follow the procedure below:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight DYNAMIC NAV-AIDS and press [ENT] or move
the ShuttlePoint knob to the right.
4. The menu now shows two selections, ON or OFF.
5. Move the ShuttlePoint knob to select the selection and press [ENT].
6. Press [CLR] until the menu disappears or an easier method is to move the ShuttlePoint
knob to the left until the chart page is shown.
6.0.5 Safety Status Bar (DSI - Data Safety Indicator)
When the Safety Status Bar is enabled, a status bar with six boxes show the status of certain
functions. Any warning or alarm condition is identified by the red color to indicate possible
risk.
To activate this function follow the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight SAFETY STATUS BAR and press [ENT] or
move the ShuttlePoint knob to the right.
4. The menu now shows the following selections: ON (The Safety Status Bar is shown),
OFF (The Safety Status Bar is not shown), ICON (The Safety Status Bar is not shown,
but a Warning alarm Icon is shown on the corner of the Chart Page as soon as any item
controlled by the DSI function returns an alarm condition. The Warning Icon remains
displayed until the alarm condition persists. Placing the cursor over this Icon, a quick
help message is shown next to the Icon, allowing the Safety Status Bar to be shown.
In this case - when the Safety Status Bar is opened via Warning alarm Icon - it is allowed
to obtain information about each “active” Safety Status box (the red ones): it is possible
to select them by ShuttlePoint knob movement left/right, and a list of active alarms is
shown underneath the selected box. By pressing [CLR], the Safety Status Bar is
removed from the screen.
5. Move the ShuttlePoint knob to select the selection and press [ENT].
6. Press [CLR] until the menu disappears or an easier method is to press the ShuttlePoint
knob to the left a few times.
Page 58
CP190i and CPF190i
2
3
BEST MAP
DATA OFF
1
O.ZOOM
4
DECLUT.
5
DANGERS
6
CAUTIONS
Safety Status Bar
1 Normal: when the chart is displayed at normal
scale.
U. Zoom: red when the chart is under-zoomed out
more than twice normal scale, gray otherwise.
O. Zoom: red when the chart is over-zoomed in
more than twice normal scale, gray otherwise.
No Chart: red when the chart is zoomed in more
than twice normal scale, gray otherwise.
WAAS 3D
2 Red when a more detailed chart is available under
the cursor position.
3 Red when at least one of the following objects or
layers is turned off (by the user) Depths/soundings;
Wrecks/obstructions; Tracks/routes; Attention Areas; Nav-Aids.
4 Displays red when clearing overlapping objects.
5 Red when &quot;Guardian Technology&quot; detects one of the following objects: Land, Intertidal, Depth
Area, Rocks, Obstructions, Shoreline Constructions, Fishing Facility, Wrecks, Dragged area,
Diffusion area, Mooring facilities, Pingos and Production installations.
6 Red when &quot;Guardian Technology&quot; detects cautionary or restricted area.
Figure 6.0.5 - Safety Status Bar
6.0.6
Satellite Imagery
This function allows to overlay the Satellite image for background chart. When it is set On,
the Palette is set to Normal to display the proper colors.
NOTE
The satellite image is only shown on 100NM, 50NM and 20NM scales.
To activate this function follow the procedure below:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight SATELLITE IMAGERY and press [ENT] or
move the ShuttlePoint knob to the right.
4. The menu now shows two selections, ON or OFF.
5. Move the ShuttlePoint knob to select the selection and press [ENT].
6. Press [CLR] until the menu disappears or an easier method is to move the ShuttlePoint
knob to the left until the Chart Page is shown.
CP190i and CPF190i
Page 59
WAAS 3D
Figure 6.0.6 - Example of Satellite Imagery
6.0.7
Currents Prediction
The worldwide database with Tidal stream information is available with MAX C-CARDs.
When data/time is available, Tidal stream arrows are shown on the charts, indicating the
direction and strength of the Tide:
Figure 6.0.7 - Tidal stream arrows
If no data/time is available from the GPS or the GPS Chart Plotter is not in Simulation mode, the
icon on the chart is generic one. The color of the arrow denotes the strength of the current as follows:
0 to 0.1 kn
0.2 to 1.0 kn
1.1 to 2.0 kn
2.1 to 3.0 kn
3.1 to 9.9 kn
-
Yellow
Yellow
Orange
Orange
Red
Figure 6.0.7a - Tidal stream arrows table
When the GPS Chart Plotter receives a valid position fix, the Tide icons are shown on the
charts on the basis of the current date and time: the screen displays and changes arrows
as date/time changes.
It is possible to see the variation of the Tidal arrows on the selected area at any given time.
To activate this function follow the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight CURRENTS PREDICTION and press [ENT] or
move the ShuttlePoint knob to the right.
Page 60
CP190i and CPF190i
4. A window is shown on the low-left side of the chart. Press [ENT] to set the date and time
manually, and [GOTO]/[MENU] to increase/decrease time; press [CLR] to exit.
6.0.8
Chart Language
The CP190i and CPF190i may be customized to show the local language of the chart.
To select the Chart Language you want:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight MAX FUNCTIONS and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight CHART LANGUAGE and press [ENT] or move
the ShuttlePoint knob to the right. A new popup window will appear on the screen. The
available functions are described in the table below.
Language
Mode
: Allows setting the language to display chart information. The language is chosen among the list
of languages available on the cartographic data (data cartridge or embedded charts).
: Defines how objects are translated. Selections are:
Off
: Enables the language chosen in the Language menu above. If the selected
language is not present on the objects information, English is used.
English : Always uses English.
Local : Uses the Local language present on C-MAP BY JEPPESEN C-CARD. If no Local
language is available, English is used.
4. After the selection is made, press [CLR] repeatedly or move the ShuttlePoint knob to
the left repeatedly until the Chart Page is shown.
NOTE
a. When the Chart Language is changed, the following settings are automatically selected: MODE
is set to Off and Chart Language is set to your selection.
b. If the C-CARD is removed or changed, the Chart Language should be confirmed and changed
if necessary.
6.0.9
Pictures or Diagrams
Using optional C-MAP BY JEPPESEN MAX data cards allows you to show pictures or diagrams
on the CP190i and CPF190i display. These Pictures are typically used to facilitate the
identification of cartographic objects or places around the chart: they can be the landscape
layout nearby a harbor, the shape of a bridge or of a buoy etc. On some objects, such as
bridges, the image associated can represent the Diagram representing the shape of the
objects and the various characteristics (length, height, type of bridge etc.).
Figure 6.0.9 - Pictures and Diagrams
CP190i and CPF190i
Page 61
How to show the Pictures or Diagrams of a Object
They are shown on the Chart Page with the camera icon
, see the figure below:
WAAS 3D
Figure 6.0.9a - Example of camera icon
Move the cursor over the camera icon. You are get the Quick Info on the object and there
is the camera icon on the top bar of the window:
WAAS 3D
Figure 6.0.9b - Example of Quick Info on camera icon
Press [ENT] for 1 second to display the image on the screen:
Figure 6.0.9c - Example of displayed image
Otherwise press [ENT] to open the Full Info on the object. Note that on the Full Info there
is the small camera icon on a corner of the square containing the object icon. To see the
picture press [MENU] when the object with a picture is highlighted.
Page 62
CP190i and CPF190i
When the picture is shown, it is possible to fit it to screen by pressing [ENT], to change the
contrast by pressing [ZOOM IN] or [ZOOM OUT] and to display the next picture associated,
if any, by moving the ShuttlePoint knob left or right.
6.0.10 Enhanced Port Info
Optional C-MAP BY JEPPESEN MAX C-CARDs include additional Port Services that were not
present before.
Additional attributes of Port Areas and Port Marinas have been included as Location,
Country, Region, State, Harbour master telephone number etc., see the following figure.
WAAS 3D
1
1 PORT icon
Figure 6.0.10 - Example of enhanced Port Info
CP190i and CPF190i
Page 63
Page 64
CP190i and CPF190i
7.
CREATING MARKS
Definitions:
MARK
Can be a stand alone position or be linked to a Route. A Mark is place on the Chart Page
using [MARK] or by entering in information in the MARK/WAYPONTS menu and selecting
NEW MARK.
WAYPOINTS
Always linked to a Route. Are placed on the Chart page using [ROUTE].
NOTE
The difference between a Mark and a Waypoint is
a. When a Route is created using WAYPOINTS and the ROUTE is deleted the WAYPOINTs are
also deleted.
b. If a Route is created using MARKS and the ROUTE is deleted the MARKs remain.
7.0
CREATING A NEW MARK USING THE CHART PAGE
1. Move the ShuttlePoint knob to the desired or approx. Lat/Lon and press [MARK].
2. You will notice a Mark is placed under the location of the Cursor and a popup window
is shown with the exact Lat/Lon of the Mark.
3. If the position is incorrect press [ENT], select EDIT using the ShuttlePoint knob and
press [ENT]: it will allow you to change the position, Mark name and icon type. Refer
to Par. 7.1 for details.
1 Mark placed under Cursor
2
4
Lat/Lon of Mark, DST/BRG
from vessel location
Press [ENT] to delete, to move,
3 to edit a Mark or to show the
Marks/Waypoint List (Directory)
2
1
3
4 Vessel location
Figure 7.0 - Mark creation
NOTE
After entering in all the Marks it is a good practice to back up the points to an User C-CARD. Refer
to Section 11.
7.1
EDITING A MARK
If a Mark has previously been created and you wish to Edit it, move Cursor over the top of
the Mark.
1. After a Mark is created press [ENT], move the ShuttlePoint knob to highlight EDIT and
press [ENT].
CP190i and CPF190i
Page 65
Figure 7.1 - Mark editing
2. The Mark Icon is selected, press [ENT]. A popup window appears:
Figure 7.1a - Mark Icons
3. Move the ShuttlePoint knob to select the desired Mark Icon, when finished press [ENT].
4. Move the ShuttlePoint knob to the right to select the Mark Name. Press [ENT] and the
first digit in the name will be highlighted.
5. Move the ShuttlePoint knob up or down to select the first character.
6. Move the ShuttlePoint knob to the right to select the next character.
7. Repeat steps 4 and 5 until the Mark name is shown. Press [ENT].
8. Move the ShuttlePoint knob to the right to select the Lat/Lon and press [ENT].
9. Move the ShuttlePoint knob up or down to select the first character.
10. Move the ShuttlePoint knob to the right to select the next character.
11. Repeat steps 9 and 10 until the desired position is shown. Press [ENT] and [CLR] to
store the Mark.
7.1.0
Deleting a Mark or Waypoint
1. Move the ShuttlePoint knob over the Mark or Waypoint to delete.
2. Press [ENT], move the ShuttlePoint knob to highlight DELETE and press [ENT]. A
popup window will be shown to confirm deleting the point.
3. Move the ShuttlePoint knob to highlight YES and press [ENT].
7.1.1
Moving a Mark or Waypoint
1. Move the ShuttlePoint knob over the Mark or Waypoint you want to move.
2. Press [ENT], move the ShuttlePoint knob to highlight MOVE and press [ENT].
3. Use the ShuttlePoint knob to move the cursor. A dotted line, connecting the previous
Waypoint position to the new position, is shown:
Page 66
CP190i and CPF190i
Figure 7.1.1 - Moving Mark or Waypoint (1)
4. Press [ENT] ([CLR] to abort the move), the Waypoint appears in the new position.
Figure 7.1.1a - Moving Mark or Waypoint (2)
7.2
MARKS/WAYPOINTS LIST
The MARKS/WPTS List shows all the Marks and Waypoints that have been stored into the
GPS Chart Plotter. This page also allows you to:
ICON
FIND
LOCATE
EDIT
NEW MARK
MODE
DELETE
SORT
SEND*
Allows sorting by icon type. Selections are:
a. SELECT - Only User Points with the selected icon are shown
b. ALL - All User Points are shown
Searches through the Marks or Waypoints to find a point by name using the ShuttlePoint knob
Shows the position of a Mark or Waypoint on the Chart page
Allows you to edit a previous stored Mark or Waypoint
Allows you to create and edit a new Mark. Useful when entering man y Marks from a list.
This selection controls how the Marks or Waypoints are shown on the Chart page. Selections are:
a. SHOW - icon and name are shown
b. ICON - only icon (no name) is shown
c. HIDE - Mark or Waypoint is hidden
d. SHOW ALL - All Marks or Waypoints are shown
e. ICON ALL - All Icons are shown without name
f. HIDE ALL - All Marks or Waypoints are hidden
Allows deleting User Points. Selections are:
a. DELETE SELECTED - for deleting the selected point
b. DELETE ALL - for deleting all stored points
Allows sorting the name of User Points. Selections are:
a. A-Z ASCENDING - Sorts the name of the Mark or Waypoint in ascending order
b. Z-A DESCENDING - Sorts the name of the Mark or Waypoint in descending order
Sends the stored points to a external device (PC) capable of listening to NMEA WPL and RTE
sentences.
CP190i and CPF190i
Page 67
RECEIVE*
When selected, receives points from an external device (PC) that is capable of sending NMEA
WPL sentence.
NOTE*
The SEND and RECEIVE functions are used to receive or transmit User Points (Marks and
Waypoints) to and from a Personal Computer (see also Par. 2.10).
Figure 7.2 - Example of Marks/Waypoints List
7.3
CREATING A NEW MARK WITH THE USER POINTS LIST
NOTE
This function is very useful if you have a list of Marks that you want to enter into the GPS Chart
Plotter.
1.
2.
3.
4.
Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press [ENT].
Move the ShuttlePoint knob to highlight MARKS/WPTS and press [ENT].
The MARKS/WAYPOINTS List page will be shown (see previous Figure).
To create a New Mark, move the ShuttlePoint knob to the right to highlight NEW MARK
and press [ENT]. A row is added for the new Mark.
5. Move the ShuttlePoint knob to highlight EDIT and press [ENT]; then press [ENT] again
to display a popup icons window and change the icon.
6. Move the ShuttlePoint knob to highlight the desired Icon and press [ENT].
7. Move the ShuttlePoint knob to the right to select the Mark name. Press [ENT] and the
first digit in the name will be highlighted.
8. Move the ShuttlePoint knob up or down to select the first character.
9. Move the ShuttlePoint knob to the right to select the next character.
10. Repeat steps 8 and 9 until the Mark name is shown. Press [ENT].
11. Move the ShuttlePoint knob to the right to select the Lat/Lon and press [ENT].
12. Move the ShuttlePoint knob up or down to select the first character.
13. Move the ShuttlePoint knob to the right to select the next character.
14. Repeat steps 12 and 13 until the desired position is shown. Press [ENT].
15. Move the ShuttlePoint knob to the right to select the Mode field and press [ENT].
16. Move the ShuttlePoint knob up or down to select the mode to show the Mark. You can
choose among SHOW to show on the chart the name and icon of Mark, ICON to show
on the chart only the icon of Mark or HIDE to hide on the Chart Page the created Mark.
Press [ENT].
17. Press [CLR] to save the created Mark.
18. Press [CLR] again and the new Mark appears on the Chart Page.
Page 68
CP190i and CPF190i
WARNING
After entering in all the Marks it is a good practice to backup the points to a User C-CARD. Refer
to Section 11.
7.4
GOTO CURSOR, ROUTE AND MARK
The CP190i and CPF190i can easily be set to start navigating to the Cursor on the Chart
Page, a saved Mark or a Route that was created.
GOTO CURSOR
1. Move the ShuttlePoint knob to the exact position you want to navigate to.
2. Press [GOTO] and a GOTO popup window will be shown
Figure 7.4 - GOTO menu (1)
3. Move the ShuttlePoint knob to highlight CURSOR and press [ENT].
Figure 7.4a - GOTO menu (2)
4. The GPS Chart Plotter is now navigating from your current position to the location
selected at step 1. A bearing line between the vessels location and the destination point
is shown. A popup window shows the Distance (DST) and Bearing (BRG) from the
vessels location to the destination point.
CP190i and CPF190i
Page 69
Figure 7.4b - GOTO menu (3)
5. The GPS Chart Plotter is in Cursor mode, to switch to Home mode press [CLR] so the
vessel will stay in the center of the page.
6. To STOP Navigation, press [GOTO] and a WARNING window is shown. Move the
ShuttlePoint knob to highlight STOP and press [ENT].
Figure 7.4c - Warning window
GOTO ROUTE
When a Route is shown on the Chart page, move thecursor over the designed Waypoint
and press [GOTO]. For more information about Routes refer to Section 9.
GOTO MARK
1. Move the ShuttlePoint knob to an open position (no buoy, warning etc. under the cursor)
on the Chart page.
2. Press [GOTO] to show the GOTO popup window.
3. Move the ShuttlePoint knob to highlight MARK and press [ENT] to show the MARKS/
WAYPOINTS List.
4. Move the ShuttlePoint Knob to the highlight the desired Mark or Waypoint and press
[GOTO].
5. You will notice a circle is drawn around the Icon Symbol. This means the GPS Chart
Plotter is now navigating to the point.
6. Press [CLR] to switch to the Chart page or Highway page to start navigating to the point.
Page 70
CP190i and CPF190i
8.
MAN OVER BOARD (MOB) FUNCTION
During navigation, the “MOB” feature provides a one-touch method of storing a location,
such as a point were a crew member fell overboard. In this mode, the CP190i or CPF190i
places a MOB point on the Chart page and all the navigation data shown is related to
navigating back to this point, allowing you to retrace your path to the MOB point efficiently.
8.0
PLACING A MOB POINT
1. On the Chart page, press [MOB] to start navigating back to the point.
2. You will notice a MOB Mark will be on the Chart page and all navigation is referring back
to this point.
3. To stop navigating to the MOB point, press [GOTO], select STOP and press [ENT].
Figure 8.0 - MOB point
8.1
DELETING A MOB POINT
1. Move the ShuttlePoint knob until the cursor is over the top of the MOB icon.
2. Press [ENT], move the ShuttlePoint knob to highlight DELETE and press [ENT]: a
popup window will be shown to confirm deleting the MOB point.
3. Move the ShuttlePoint knob to highlight YES and press [ENT].
Figure 8.1 - Deleting MOB point
CP190i and CPF190i
Page 71
Page 72
CP190i and CPF190i
9.
ROUTES
The CP190i and the CPF190i have the capability to store 50 Routes with 100 Waypoints
or Marks in each Route. A Route can consist of Waypoints or Marks. The difference is when
a Route is made using Waypoints and the Route is deleted the Waypoints are also deleted.
However if a Route is made of Marks and the Route is deleted the Marks stay in memory.
WPT002
WPT001
(Destination)
PERPENDICULAR TO
THE NAVIGATION LINE
NAVIGATION LINE
(or DESTINATION Line)
Navigation Course
STARTING Position
When the Ship passes the
perpendicular of the
NAVIGATION LINE, the
Destination is moved to then
next Waypoint in the Route
SHIP
Figure 9 - Example to show how the plotter switches from one Waypoint to another
9.0
CREATING A ROUTE USING WAYPOINTS
1. On the Chart Page move the ShuttlePoint knob to the Lat/Lon of the Starting Waypoint
in the Route.
2. Press [ROUTE], you will notice the Starting Waypoint
will be placed under the
cursor.
in the Route.
3. Move the ShuttlePoint knob to the second Lat/Lon of the next leg
4. Press [ROUTE]. You will notice another Waypoint is shown under the cursor and a line
joins the starting Waypoint to the Second Waypoint.
Figure 9.0 - Creating a Route using Waypoints
5. Repeat steps 3 and 4 until all Waypoints are entered into the Route.
CP190i and CPF190i
Page 73
NOTE
At this point the Route is saved as ROUTE01. If you would like to save the Route under a specific
name follow the next steps.
9.1
CHANGING THE NAME OF A ROUTE
To name the Route:
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight ROUTE and press [ENT].
3. Move the ShuttlePoint knob to highlight EDIT ROUTE and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight NAME and press [ENT]. A popup window will
be shown.
5. Move the ShuttlePoint knob up/down to change the characters and left/right to select
a different character in the Route’s Name.
EDIT ROUTE
Figure 9.1 - Edit Route (Route Report)
6. When finished press [ENT] to save.
7. Press [CLR] to show the Chart Page.
9.2
CREATING AN OLYMPIC ROUTE
This feature allows the starting point in a Route to be saved as the final destination point.
1. On the Chart page move the ShuttlePoint knob to the Lat/Lon of the Starting Waypoint
in the Route.
2. Press [ROUTE], the Starting Waypoint will be placed under the cursor.
3. Move the ShuttlePoint knob to the second Lat/Lon of the next leg in the Route.
4. Press [ROUTE]. Another Waypoint is shown under the cursor and a line joins the
Starting Waypoint to the second Waypoint.
5. Repeat steps 3 and 4 until all Waypoints are entered into the Route.
Page 74
CP190i and CPF190i
Figure 9.2 - Olympic Route creation (1)
6. Then move the ShuttlePoint knob to the last Waypoint and press [ENT].
7. Move the ShuttlePoint knob to highlight OLYMPIC and press [ENT]. A line joins the
starting Waypoint and the last Waypoint.
Figure 9.2a - Olympic Route creation (2)
9.3
MAKING ADDITIONAL ROUTES
To create another Route the GPS Chart Plotter must be told that you want to create a second
Route.
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight ROUTE and press [ENT].
3. Move the ShuttlePoint knob to highlight SELECT and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to an open Route number example Route 2.
5. Press [ENT] or move the ShuttlePoint knob to the right.
6. Press [CLR] or move the ShuttlePoint knob to the left until the Chart Page is shown.
7. To create the new Route, follow the steps in Creating a Route using Waypoints or Marks
sections.
9.4
CREATING A ROUTE USING MARKS ON THE CHART PAGE
To create a Route containing Marks you first must create the Marks and show them on the
Chart Page.
1. Move the ShuttlePoint knob over the top of a Mark that you wish to be the starting point
in the Route and press [ROUTE].
2. Next move the ShuttlePoint knob until the cursor is over the Mark that you want to be
the next leg in the Route.
CP190i and CPF190i
Page 75
3. Press [ROUTE]. You will notice a bearing line joins the first and second Mark which
means these Marks are selected into the Route.
4. Repeat steps 3 and 4 until all Marks are entered into the Route.
NOTE
At this point the Route is saved as ROUTE01. If you would like to save the Route under a specific
name follow the remaining steps.
5. To name the Route press [MENU]. Move the ShuttlePoint knob to highlight USER
POINTS and press [ENT].
6. Move the ShuttlePoint knob to highlight ROUTE and press [ENT].
7. Move the ShuttlePoint to highlight EDIT ROUTE and press [ENT] or move the
ShuttlePoint knob to the right.
8. Move the ShuttlePoint knob to highlight NAME and press [ENT] or move the ShuttlePoint knob to the right. A popup window will be shown.
9. Move the ShuttlePoint knob up/down to change the characters and left/right to select
a different character in the Routes Name.
10. When finished press [ENT] to save.
11. Press [CLR] to show the Chart Page is shown.
9.5
INSERTING A WAYPOINT INTO A ROUTE
Place the cursor on the navigation line between two Waypoints and press [ROUTE]. The
line between the two Waypoints is turned into a dotted line, see the following picture.
Figure 9.5 - Inserting Waypoint procedure (1)
Move the ShuttlePoint knob to the desired location for the new Waypoint: the line will
“rubber-band”, drawing a dotted line between the previous Waypoint and the cursor, and
another dotted line between the cursor and the next Waypoint (see the left side of the above
picture). Once you have positioned the cursor at the location you want, press [ENT] (see
the right side of the above picture).
Figure 9.5a - Inserting Waypoint procedure (2)
Page 76
CP190i and CPF190i
9.6
GOTO A ROUTE
By having created some Routes, you can choose one of them to place a GOTO on.
9.6.0
Using [GOTO] to select Route
1. Move the ShuttlePoint knob to an open position (no buoy, warning etc. under the cursor)
on the Chart Page.
2. Press [GOTO] to show the GOTO popup window.
3. Move the ShuttlePoint knob to highlight ROUTE and press [ENT].
4. The SELECT ROUTE popup window will be shown.
Figure 9.6.0 - GOTO ROUTE procedure (1)
5. Move the ShuttlePoint knob to the highlight the desired Route and press [ENT].
6. On the Chart page a circle with a flag is shown on the first leg of the Route and a navigation
line is shown, indicating the GPS Chart Plotter is navigating to the first Waypoint in the
Route.
Figure 9.6.0a - GOTO ROUTE procedure (2)
9.6.1
Using the ShuttlePoint knob
1. On the Chart page move the ShuttlePoint knob until the cursor reaches the starting point
of the Route.
2. Press [GOTO] to start following the Route.
3. Press [CLR] twice to revert to Home mode.
9.7
DELETING A ROUTE
To delete a Route follow the procedure below:
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
CP190i and CPF190i
Page 77
2. Move the ShuttlePoint knob to highlight ROUTE and press [ENT].
3. Move the ShuttlePoint knob to highlight DELETE and press [ENT] or move the
ShuttlePoint knob to the right.
4. A Warning message appears to confirm. Move the ShuttlePoint knob to highlight YES
and press [ENT]. The Route has been deleted.
WARNING
An active Route (one that you are navigating to) cannot be deleted until you stop navigating to the
Route.
9.8
OTHER SETTINGS IN ROUTE MENU
You will notice the ROUTE menu has other selections.
SELECT
REVERSE
COLOR
EDIT
SEND
RECEIVE
THICKNESS
9.8.0
Choose an available Route to create or choose a stored Route to show and follow on the Chart page.
Reverses the Route, when chosen Starting point is at the end of the Route.
Allows changing the color of the navigation lines between each leg in the Route.
The Edit Route (Route Report) menu is useful to show details of the Waypoints contained within the
Route. This menu also allows you to enter in your average speed and fuel consumption and calculate
the approximate fuel used when following the Route.
Sends the stored points to a external device (PC) capable of listening to NMEA RTE sentence.
Receive the points from an external device (PC) capable of sending NMEA RTE sentence.
Selection that allows the Route line to be easily seen; default selection is Thick.
Route Check
The Route Check function is used after you have created a Route to ensure you and your
vessel will not have problems while navigating. This is done by the CP190i and CPF190i by
reviewing the Route and looking for the following hazards that may effect safe navigation.
&middot; Land Areas
&middot; Shallow Water
&middot; Intertidal Areas (areas emerged at low tide)
&middot; Rocks
&middot; Wrecks
&middot; Obstructions
&middot; Shoreline Constructions
&middot; Fishing Facility
&middot; Dredged Areas
&middot; Diffusers (submarine pipeline)
&middot; Mooring/Warping Facility
&middot; Production Installation (an installation for the exploitation of natural resources)
&middot; Pingos (small conical hills having a large central core of ice formed from the
encroachment of permafrost and the resulting hydrostatic pressure)
&middot; No Data Available (no adequate data coverage)
If any of these alarm conditions is detected, the function returns the list of dangerous objects
and the relative dangerous Route leg, that is drawn with a different color.
&middot; Route legs which were classified as dangerous are displayed in RED. It means that
there is at least one dangerous object in the vicinity of this leg and it has been found.
&middot; Route legs which were classified as safe are displayed in GREEN. It means that the
data was checked on detailed chart levels and no problems were found for all segments
of the leg.
Page 78
CP190i and CPF190i
&middot; Route legs for which there was not sufficient data to be checked are displayed in
YELLOW. It means that no problems were found but the data was not sufficient or not
available at all to classify such a leg as safe.
Figure 9.8.0 - Example of dangerous objects found on the chart
To activate this function:
AUTOMATIC CHECK
Turns the Route Check feature On or Off. Turn the Automatic Route Check on after you
have created a new Route, or if you inserted a new Waypoint, deleted, moved or edited
any Waypoint in a saved Route to confirm the Route can be safely navigated.
This selection allows you to select the width from the left and right of the Route leg where
the GPS Chart Plotter will check to confirm navigation threats. See the picture below. The
default for this selection is 0.04NM.
This selection allows you to select the water depth in the Route width area so the GPS
Chart Plotter can check and confirm underwater threats. It checks if some objects with
the depth attribute (like Shallow Water, Dredged Areas, Diffusers, Obstructions, Pingos,
Production Installation and Wrecks) are above this depth level. Only if the depth attribute
is above the depth limit are they found and considered as dangerous. See the picture
below. The default setting is 10FT.
Defines a segment length into which a leg of the Route is divided in order to execute the
search for dangerous objects with better accuracy. When accuracy is maximal, a
segment length is the shortest. When accuracy is minimal, a segment length is the
longest. Selects among Minimum, Low, Medium, High and Maximum. See the picture
below. The default setting is Medium.
Shows the list of the dangerous objects found on the charts crossed by the Route.
ROUTE WIDTH
DEPTH LIMIT
ACCURACY
ROUTE CHECK REPORT
F
E
C
A
A-B = Width
C-D = Depth
E-F = Accuracy
B
D
Figure 9.8.0a - Route Check parameters
CP190i and CPF190i
Page 79
NOTE
Although the functionality is called Route Check, it can also be activated when the navigation is set
to a single point (like DSC, MOB, Mark). In the case of checking a single point towards which the
navigation is started, the leg for which the Route Check is executed is defined by the current position
(the leg’s starting point) and the destination point (the leg’s ending point).
Page 80
CP190i and CPF190i
10. TRACKS
The CP190i and the CPF190i have the capability to store 20 individual Tracks and record
up to 10000 Track Points.
Before using the Track function you will need to setup the Track function that suits your boat.
The Track function records your tracks your vessels location as it moves through the water.
The Track function can be setup to lay down a Track for a predetermined time or distance
interval. If you have a fast moving boat you may want to setup the CP190i and the CPF190i
to record a Track point every 0.5NM or if you have a sail boat you may want to setup to lay
down a Track point once every 1 minute.
NOTE
Please note the Track point memory capacity is 10,000 points. This means for a long journey you may
have to adjust the time or distance to be able to track your journey. It should be noted when the 10,000
Track points are used up, the first Track point layed down will be deleted when a new point is placed
on the chart.
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight TRACK and press [ENT].
3. Move the ShuttlePoint knob to highlight STEP UNIT and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight Dist or Time and press [ENT] or move the
ShuttlePoint knob to the right.
Figure 10 - Distance Units and Time Units
5. Move the ShuttlePoint knob to highlight DISTANCE or TIME step interval and press
[ENT] or move the ShuttlePoint knob to the right.
6. Move the ShuttlePoint knob up/down to the desired step value and press [ENT] or move
the ShuttlePoint knob to the right.
7. Press [CLR] or move the ShuttlePoint knob to the left until the Chart Page is shown.
10.0
TRACKING
When using the tracking feature you will notice every time a Track Point is layed down on
the Chart page a small filled in circle is shown on the Track line. If you move the cursor over
the top of the circle a popup window will be shown with the Time, Water Temperature, Speed
and Course Over Ground (COG). This is very useful if you are fishing and want to review
the conditions where the fish were being caught.
CP190i and CPF190i
Page 81
Figure 10.0 - Tracking
10.0.0 Saving and starting a new Track
A Track is automatically saved and retained in memory when the power is turned off. To start
a new Track:
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight TRACK and press [ENT].
3. Move the ShuttlePoint knob to highlight ACTIVE TRACK and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob up/down to select the next available open Track and press
[ENT] or move the ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob to highlight TRACKING and press [ENT] or move the
ShuttlePoint knob to the right to set On.
6. Press [CLR] or move the ShuttlePoint knob to the left until the Chart Page is shown.
7. A new Track now will be laid down.
10.0.1 Deleting a Track
To delete a Track:
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight TRACK and press [ENT].
3. Move the ShuttlePoint knob to highlight DELETE and press [ENT] or move the
ShuttlePoint knob to the right.
4. A warning popup window will be shown to confirm if you want to reset the Track. Move
the ShuttlePoint knob to highlight YES and press [ENT] or move the ShuttlePoint knob
to the right. The Track is now deleted.
5. Press [CLR] or move the ShuttlePoint knob to the left until the Chart Page is shown.
10.0.2 Other settings
You will notice the Track menu has other selections:
TRACKING
ACTIVE TRACK
VISIBLE
LINE COLOR
DELETE
STEP UNIT
Page 82
Allows turning on or off the tracking function
This selection allows you to save a Track to one of the 20 Tracks available
Shows or hides a Track shown in ACTIVE TRACK menu
Selects the color of the Track line
Deletes a Track selected in the ACTIVE TRACK menu
Allowable selection are Distance or Time
CP190i and CPF190i
DISTANCE
TIME
10.1
User adjustable Distance interval of when Track point is laid down on the Chart page.
User adjustable Time interval of when Track point is laid down on the Chart page.
TRIP LOG
10.1.0 Using the Trip Log
On the Chart, Navigation, Highway and NMEA Data pages the windows may be customized
to show Trip Log information.
1. Select one of the pages listed above, press and hold [MENU]. You will notice one of the
data boxes will be highlighted.
2. Press [ENT] and move the ShuttlePoint knob to highlight TLOG, press [ENT] or move
the ShuttlePoint knob to the right.
3. A popup window will be shown with Nm (Nautical Mile), Sm (Statute Mile), Km
(Kilometer) and RESET. Move the ShuttlePoint knob to select the desired units of
measure and press [ENT] or move the ShuttlePoint knob to the right.
4. Press [CLR] or move the ShuttlePoint knob to the right until the selected page (Chart,
Navigation, Highway or NMEA Data Page) is shown.
10.1.1 Setup / Reset
When Trip Log is selected in one of the data windows and you want to reset the log:
1. Press and hold [MENU] until a field is highlighted (it will be shown in a yellow frame).
2. Move the ShuttlePoint knob to highlight the Trip Log window TLOG and press [ENT].
3. A popup window will be shown. Move the ShuttlePoint knob to TLOG and press [ENT].
4. Another popup window will be shown. Move the ShuttlePoint knob to RESET and press
[ENT].
5. A warning popup window will be shown to confirm if you want to reset the Trip Log. Move
the ShuttlePoint knob to highlight YES and press [ENT].The Trip Log is now reset.
6. Press [CLR] to store and exit the editing mode
Figure 10.1. 1 - Trip Log Reset
CP190i and CPF190i
Page 83
Page 84
CP190i and CPF190i
11. USER C-CARD
The optional User C-CARD is used to backup Marks, Routes, and Tracks stored in your
GPS Chart Plotter's memory. In the USA the User C-CARD is available directly from
Jeppesen Marine at 800/424-2627. The User C-CARD is similar to a backup disk used with
a PC, in case you have to clear the RAM to resolve an issue or load new software, or if you
would like to transfer Waypoint, Track and Route information from one STANDARD
HORIZON GPS Chart Plotter to another.
11.0
USER C-CARD MENU
This optional card is similar to using a floppy disk or memory stick on a PC to backup your
files or to transfer the information tht you have stored to a friends GPS Chart Plotter. The
information shown below will assist you to transfer the User Points, Routes and Track
history to the optional User C-CARD.
1 Time of file creation
1
4
2 Date of file creation
3
Type of data contained in the
file (Mark file, Waypoint file...)
4 File name
2
5
6
5 Number of Selected file
Information on stored User
6 Points on Internal Memory
3
Figure 11.0 - User C-CARD Menu
11.0.0 Formatting the optional User C-CARD
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT].
3. Move the ShuttlePoint knob to highlight FORMAT and press[ENT].
4. A popup Warning window will to confirm you want to format the User C-CARD.
5. Select YES and press [ENT] to confirm (select NO otherwise). The format of User
C-CARD must be done before using a new User C-CARD: this operation prepares the
User C-CARD to receive and store information.
NOTE
Formatting permanently erases all files previously saved on the User C-CARD.
11.0.1 Transferring files to the optional User C-CARD
1. Remove a C-MAP B JEPPESEN NT+/MAX C-CARD if present and insert the optional
User C-CARD into the slot.
CP190i and CPF190i
Page 85
2. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
3. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT].
4. A screen will appear. Move the ShuttlePoint knob to the left to highlight SAVE and
press [ENT].
5. A popup SAVE FILE window will appear. In this window you can change the name
and the file type by using the ShuttlePoint knob and pressing [ENT], when finished
press [CLR] once.
6. To save the file, move the ShuttlePoint knob to SAVE in window and press [ENT].
7. A Information pop window will momentarily be shown SAVING then show SAVING OK.
8. Press [ENT] to confirm.
11.0.2 Loading a file from the optional User C-CARD
If you have a problem and accidentally loose the User Points in the GPS Chart Plotter
with the optional User C-CARD it is possible to load the data back into the GPS Chart
Plotter using the following procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT].
3. Select the saved file from the User C-CARD list by using the ShuttlePoint knob and
press [ENT].
4. Move the ShuttlePoint knob to the left to highlight LOAD and press [ENT].
5. A popup information window will appear when loading is complete.
6. Press [ENT] to confirm.
11.0.3 Deleting a file from the optional User C-CARD
You may want to delete a saved file on the User C-CARD.
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT].
3. Select the saved file from the User C-CARD list by using the ShuttlePoint knob and
press [ENT].
4. Move the ShuttlePoint knob to the left to highlight DELETE and press [ENT].
5. A popup Warning window will to confirm you want to delete the file.
6. Press [ENT] to confirm.
11.0.4 Refreshing the optional User C-CARD
You may want to change the User C-CARD inserted in the slot with a new one.
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT].
3. Open the door, remove the User C-CARD from the slot and insert another User
C-CARD into the same slot.
4. Move the ShuttlePoint knob to highlight REFRESH and press [ENT]. This &quot;new&quot;
User C-CARD is now ready to receive and store information.
Page 86
CP190i and CPF190i
12. PAGES
The CP190i and CPF190i have many pages that are designed to ease your navigation.
NAVIGATION
CHART
WAAS
GPS STATUS
3D
NMEA DISPLAY
WAAS
CELESTIAL
HIGHWAY
WAAS
3D
Chart and Fish Finder
Display example with RADAR connected
3D
Figure 12 - Example of screen display pages
The pages can be selected in the following way:
1. Press [MENU]. The following menu is shown on the screen:
Figure 12a - Main Menu
2. Move the ShuttlePoint knob to highlight the desired page and press [ENT].
12.0
CHART PAGE
The Chart page is the main page of the GPS Chart Plotter. From this page the user can zoom
in/out, pan around the chart, show information about cartographic objects, see the exact
vessel position with the COG and SOG, place points, GOTO a destination point, show Track
history etc. The GPS Chart Plotter come with Built-In Charts for coastal navigation of USA
including Alaska, Hawaii and Great Lakes, Canada, Bahamas, Caribbean, Cuba, Puerto
Rico, and Central America. For detail refer to Par. 5.0. For more detail, optional C-MAP BY
JEPPESEN NT+/MAX C-CARDs or to update the Built-In Charts, refer to Par. 5.1.
It is possible to set the chart as a single or two charts side by side.
1. Press [MENU], move the ShuttlePoint knob to highlight CHART and press [ENT].Two
Chart Page types are available: Single and Dual.
CP190i and CPF190i
Page 87
2. Move the ShuttlePoint knob to highlight Single or Dual and press [ENT].
WAAS 3D
WAAS 3D
Figure 12.0 - Chart selection menu
NOTE
may appear on the unused window of the Dual Chart page. It happens when the GPS Chart
Plotter updates the displayed chart in the not active window. So the user understands that the GPS
Chart Plotter is busy.
12.0.0 Change Focus on Dual Chart Page
When Dual Chart is selected, you will notice one of the chart windows will have a red boarder
around it. This red boarder indicates which chart window the chart plotter has the Focus on,
meaning if the ShuttlePoint knob is moved the cursor on chart window will move. The focus
may be changed to to the other chart window with the procedure below:
1. Press and hold [FIND] for 2 seconds. The red boarder around the window is moved from
active window to the other.
Repeat the step 1. to move the focus from a window to another.
12.0.1 Single Chart Page
1
1 Time
2
3
2 Speed Over Ground
4
WAAS 3D
5
3 Course Over Ground
4 Fix status
Time To Go
5 (If plotter is not navigating to a
point TTG will show --:-- )
Distance from Fix to Destination
6 (If plotter is not navigating to a
point DST will show ---.- )
Bearing from Fix to Destination
7 (If plotter is not navigating to a
point BRG will show --- o )
8 Chart Scale
6
8
7
9
10
9 Cursor Coordinates
10 Distance &amp; Bearings from Fix to Cursor
Figure 12.0.1 - Example of single Chart Page
Page 88
CP190i and CPF190i
12.0.2 Window Selections
The default is the Two Line Small window. The CP190i and CPF190i windows may be
changed by the procedure below.
FULL CHART (None)
1 LINE SMALL
GENERAL
1 LINE LARGE
WAAS
WAAS
2 LINES SMALL
HIGHWAY
3D
COMPASS
Figure 12.0.2 - Data window layout
1. To change, press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and
press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight WINDOWS SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight CHART PAGE and press [ENT] or move the
ShuttlePoint knob to the right.
5. Select the desired window, HIGHWAY or COMPASS, and press [ENT] or move the
ShuttlePoint knob to the right.
6. Press [CLR] or move the ShuttlePoint knob to exit the menu and show the Chart Page.
12.0.3 Customizing the Data Windows
The data fields contained on the General, 1 Line Small/Large and 2 Line Small data windows
can be changed to the following selections:
&middot; MAX SPD = Max Speed
&middot; SOG
= Speed Over Ground
&middot; COG
= Course Over Ground
&middot; DST
= Distance to Destination1
&middot; BRG
= Bearing to Destination1
&middot; XTE
= Cross Track Error
&middot; TTG
= Time To Go
&middot; STR
= Steering
&middot; HDG
= Heading from Electronic Compass
&middot; DTP
= Depth
&middot; SPD
= Speed
&middot; ALT
= Altitude
&middot; AWS
= Apparent Wind Speed
&middot; AWD
= Apparent Wind Direction
&middot; TWS
= True Wind Speed
&middot; TWD
= True Wind Direction
CP190i and CPF190i
Page 89
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
HDOP
VDOP
Temp
TLOG
DATE
TIME
VMG
ETA
TRACKING
SCALE
GPS Status
=
=
=
=
=
=
=
=
=
=
=
Horizontal Dilution of Precision
Vertical Dilution of Precision
Water Temperature
Trip Log
Current Date
Current Time
Velocity Made Good
Estimated Time of Arrival
Tracking
Chart Scale
Shows GPS Fix Status (WAAS, 3D, 2D, ...)
NOTE1
When the GENERAL window is selected and the GPS chart plotter is in Home Mode, the BRG will
show - - -, unless the GPS chart plotter is navigating to a point. When in Cursor Mode, the BRG
shows the Bearing from the ship’s position to the cursor location.
To select the desired field, follow the procedure:
1. Press and hold [MENU] until a field is highlighted (it will be shown in a yellow frame).
2. Move the ShuttlePoint knob to the desired data field (the yellow frame is moved to the
desired data field) and press [ENT]. The popup window will be shown.
3. Move the ShuttlePoint knob up/down or left/right to choose the desired setting and press
[ENT].
4. Press [CLR] to store and exit the editing mode.
NOTE
Data window field on the NAVIGATION, HIGHWAY, GPS STATUS and NMEA pages may be
customized in the above manner.
WAAS 3D
AAS 3D
WAAS 3D
Figure 12.0.3 - Customizing the Data Windows
NOTE
See Par. 10.1.0 if Trip Log is selected in one of the data windows and you want to reset the log.
12.0.4 Additional Functions on Chart Page
When on the Chart page you will notice icons of Buoys, Towers, Lights, Wrecks, Tide
Stations and Port Icons. If the cursor is moved over the top of these icons a popup window
will be shown with information about the icon.
Page 90
CP190i and CPF190i
12.0.5 Turning Off Information on Icon Points
The GPS Chart Plotter allows you to select to see information On Points, On All items or
to turn this function Off. The default setting is On Points.
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight AUTO INFO and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob up or down to highlight OFF, ON POINTS or ON ALL and
press [ENT] or move the ShuttlePoint knob to the right.
5. Press [CLR] or move the ShuttlePoint knob to the left until the Chart Page appears.
AUTO INFO Off
AUTO INFO On Points
AUTO INFO On All
Figure 12.0.5 - Example of Auto Info settings
12.0.6 Display Mode
Selects from a pre-defined table what cartographic objects are displayed and which display
options are set. Pre-programmed settings are user selectable from Full, Medium, Low,
Radar (reduces the information on the display to simulate items that would be shown on a
RADAR display. Please note this function is not actually showing RADAR information it is
only showing what typically would be shown by a separate dedicated RADAR display),
Tides, Custom (default mode).
To change to one of the pre-programmed settings
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight CHART CONFIGURATIONS and press [ENT]
or move the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight DISPLAY MODE and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob up or down to select the preset and press [ENT].
5. Press [CLR] or move the ShuttlePoint knob to the right until the Chart Page is shown.
CHART
Figure 12.0.6 - Display Mode settings
CP190i and CPF190i
Page 91
The table below shows the selections for each mode:
Setting
Full
Place Names
On
Name Tags
On
Nav Aids &amp; Light Sectors
On
Attention Areas
On
Tides &amp; Currents
On
Seabed Type
On
Ports &amp; Services
On
Tracks &amp; Routes
On
Depth Range Min
0FT
Depth Range Max
32804FT
Land Elevations
On
Land Elevation Values
On
Roads
On
Points Of Interest
On
Lat/Lon Grid
On
Chart Boundaries
On
Value Added Data
On
Chart Lock
On
Mixing Levels
On
Underwater Ob. Limit
1000FT
Rocks
Icon + Depth
Obstructions
Icon + Depth
Diffusers
Icon + Depth
Wrecks
Icon + Depth
Medium
Low
Radar
Tides
Custom
(Default values)
On
Off
No Sectors
On
Off
Off
On
Off
0FT
32804FT
On
Off
Off
Off
Off
Auto
Off
On
On
32FT
Icon
Icon
Icon
Icon
On
Off
No Sectors
Off
Off
Off
Off
Off
0FT
32804FT
Off
Off
Off
Off
Off
Off
Off
On
On
32FT
Icon
Icon
Icon
Icon
On
Off
No Sectors
Off
Off
Off
On
Off
0FT
32804FT
Off
Off
Off
Off
Off
Off
Off
On
On
32FT
Icon
Icon
Icon
Icon
On
Off
Off
Off
On
Off
Off
Off
0FT
32804FT
Off
Off
Off
Off
Off
Off
On
On
On
32FT
Icon
Icon
Icon
Icon
On
Off
On
Off
On
On
On
On
0 Ft
32804FT
Off
On
On
On
Off
Off
On
On
On
1000FT
Icon
Icon
Icon
Icon
12.0.7 Marine Settings
To control the display on the chart of the marine features.
Place Names
Name Tags
: Turns the local area names On or Off.
: Turns a tag for particular chart objects that either includes the Name of the chart object or
the Depth of an Underwater chart object On or Off.
Nav Aids &amp; Light Sectors: Turns the presentation of Lights, Signals, Buoys and Beacons On (Nav-Aids &amp; Light
Sectors are shown), Off (Nav-Aids &amp; Light Sectors are not shown) or No Sector (Nav-Aids
are shown, Light Sectors are hidden).
Attention Areas
: Turns the Attention Areas (areas in which special attention by the mariner is required
because of natural or man-made hazards sailing regulations and restrictions) On or Off.
Tides &amp; Currents
: Turns the Tides and Currents On or Off.
When data/time is available, Tidal stream arrows are shown on the charts, indicating the
direction and strength of the Tide. If no data/time is available from the GPS or the GPS
Chart Plotter is not in Simulation mode, the icon on the chart is generic one. The color of
the arrow denotes the strength of the current as follows:
0 to 0.1 kn
0.2 to 1.0 kn
1.1 to 2.0 kn
2.1 to 3.0 kn
3.1 to 9.9 kn
Seabed Type
Ports &amp; Services
Page 92
-
Yellow
Yellow
Orange
Orange
Red
When the GPS Chart Plotter receives a valid position fix, the Tide icons are shown on
the charts on the basis of the current date and time: the screen displays and changes
arrows as date/time changes.
: Turns the Seabed type On or Off.
: Turns the Ports and Service icons On of Off. Areas along the shore with facilities for
mooring, downloading and uploading of ships, generally sheltered from waves and winds.
Port installations are piers, wharves, pontoons, dry docks, cranes....
CP190i and CPF190i
Tracks &amp; Routes
: Turns the underwater objects On or Off. Objects are obstructions, wrecks, cable etc.
12.0.8 Depth Settings
To control the display on the chart of the depth informations.
Depth Range Min
Depth Range Max
: Sets the minimum depth limit to show Depth Sounding, Bathymetric Lines and Depth Area.
: Sets the max depth limit to show Depth Sounding, Bathymetric Lines and Depth Area.
50-100 Ft
0-1000 Ft
Figure 12.0.8 - Depth Settings
12.0.9 Land Settings
To control the display on the map of the terrestrial features.
Land Elevations
Land Elevation Values
Roads
Points Of Interest
:
:
:
:
Turns the Land Elevations On or Off.
Turns the Land Elevation Values On or Off.
Turns the Roads On or Off.
Turns the Points of Information On or Off.
1
2
1 ROAD
2 POINT OF INTEREST (LIBRARY)
Figure 12.0.9 - Example of Roads and Points Of Interest
12.0.10
Chart Settings
Settings that control how the chart features will be shown on the Chart Page of the GPS
Chart Plotter.
CP190i and CPF190i
Page 93
Lat/Lon Grid
: Turns the Latitude and Longitude grid lines on or off on the chart page. See the following figure:
Lat/Lon Grid OFF
Lat/Lon Grid ON
Chart Boundaries : Turns the Chart Boundaries On, Off or Auto. The Chart Boundaries are the “ticked” boxes
sourround the coastline. Each box indicates an area where more detail is available. The Chart
Boundaries are only show when a C-MAP BY JEPPESEN NT+ or MAX CARD is inserted into the GPS
Chart Plotter. See the pictures below:
Chart Boundaries ON
Chart Boundaries OFF
Value Added Data : Turns the Value Added Data On or Off. The Value Added Data (VAD) is a collection of additional
cartographic objects which are not present on the original paper chart (from which the electronic
chart derives). These objects have been obtained from other sources and then merged to the
electronic charts in order to provide more information useful for the navigation. VAD object can
be any cartographic objects and it can be distinguished from the official-chart-objects from the
Quick Info. A dedicated icon is shown on the Quick Info window to indicate that the object queried
is a VAD. The same icon is also shown on the Full Info page and in addition the extended text Value
Added Data is shown on the details of the VAD object. See the figure below:
1
1 Example of VAD object
Chart Lock (*)
Mixing Levels
Page 94
: Turns the chart function On/Off. When Chart Lock is On, the available zoom scales are only the
ones containing cartographic data. Instead when Chart Lock is Off, it is possible to zoom down
into zoom scales not covered by cartographic data after the last available zoom scale covered by
cartographic data. The DSI (Data Safety Indicator) window, if present, will show “NO CHART”,
when an empty level is entered in the location of chart expansion mode.
: When the chart coverage at the current chart scale does not fill the entire display, the GPS Chart
Plotter draws the rest of the chart using charts from above and below the current scale. When this
function is turned on you will notice the display may redraw 2 to 3 times to show all the details.
CP190i and CPF190i
NOTE(*)
When an empty level is entered, the message “No cartographic coverage” is shown on a window
in a corner of the chart display. The warning message is always displayed as long as the current
zoom has no data coverage.
12.0.11
Underwater Objects Settings
The following selections are used to control which Underwater Objects are shown on the
Chart Page.
Underwater Object Limit : Selects the max depth value to display Underwater Objects. If value is set to 0 Feet, the
Underwater Objects are not shown on the charts. Menu options are grayed out. If value is more
than 0 Feet (i.e. 10 Feet), in the Range from 0 Feet to the selected value the Underwater Objects
are displayed according to their setting below.
Rocks
: Sets Off/Icon/Icon+Depth* the displaying of the Rocks.
Obstructions
: Sets Off/Icon/Icon+Depth* the displaying of the Obstructions.
Diffusers
: Sets Off/Icon/Icon+Depth* the displaying of Diffusers (Diffuser is a structure on an outfall
through which liquids are discharged. The structure will usually project above the level of the
outfall and can be an obstruction to navigation).
Wrecks
: Sets Off/Icon/Icon+Depth* the displaying of Wrecks.
NOTE(*)
Choose the options: OFF (the object is not visible independently of the selected “Underwater Object
Depth Value”); ICON (the object icon is visible without tags, in the range selected from “Underwater
Object Depth Value” option); ICON+DEPTH (the object icon and tag is visible, in the range selected
from “Underwater Object Depth Value” option).
12.1
CUSTOMIZING CHART SETTINGS
The GPS Chart Plotter also allows you to customize items shown on the chart (discussed
in above sections) instead of using a pre-defined table discussed in Par. 12.0.4 Display Mode.
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight CHART CONFIGURATIONS and press [ENT]
or move the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight DISPLAY MODE and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight Custom and press [ENT] or move the
ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob up or down to select the desired item within the groups
Marine Settings, Depth Settings, Land Settings, Chart Settings or Underwater Settings
and press [ENT]. See the above sections for details on selections.
12.2
NAVIGATION PAGE
This page is useful to show information when heading to a destination, following a compassa
heading or navigating to a Mark or a Route. The default page is shown with a Compass
Rose, however this can be customized to show a Compass Tape.
1. To change to show the Compass Tape, select the Chart Page, press [MENU]. Move the
ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight GENERAL SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
CP190i and CPF190i
Page 95
3. Move the ShuttlePoint knob to highlight WINDOW SETUP and press [ENT] and press
[ENT] or move the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight NAVIGATION PAGE and press [ENT] and
press [ENT] or move the ShuttlePoint knob to the right.
5. Move the ShuttlePoint up or down to select COMPASS TAPE and press [ENT].
6. Press [CLR] or move the ShuttlePoint knob to the right until the Chart Page is shown.
1 Fix position
1
2 Time
2
3 Speed Over Ground
3
WAAS
4 Course Over Ground
3D
4
5 Bearing to Destination
8
5
6 Time To Go
7 Distance to Destination
6
8 Compass Rose
7
Figure 12.2 - Navigation page with Compass Rose
1 Fix position
5
2 Compass Tape
1
3 Time
WAAS
3D
2
4 Time To Go
5 Speed Over Ground
6 Distance to Destination
7 Course Over Ground
6
3
7
4
8
8 Bearing to Destination
Figure 12.2a - Navigation page with Compass Tape
NOTE
The COG heading is computed and supplied to the plotter from the internal GPS or external GPS.
12.3
HIGHWAY PAGE
Shows a 3D view of the vessel travelling through the water when Navigating to a destination
point, Mark or following a Route. Press [ZOOM IN] or [ZOOM OUT] to change the highway
scale.
Page 96
CP190i and CPF190i
1 Speed Over Ground
1
2 Course over ground
2
3 Bearing
3
4 Highway Display
4
5 Highway Scale
5
WAAS
3D
Figure 12.3 - Highway page
12.4
CELESTIAL PAGE
The Celestial page contains Tide information critical for safe navigation. This page is also
useful for boaters that are concerned about the height of the water under a bridge or by
fisherman that wish to know the tide and moon phase of a specific date.
Changing date
1. Press [ENT] and a popup window will be shown.
2. Moving the ShuttlePoint knob up or down changes the digits and left and right selects
the month, day and year.
3. Press [CLR] to exit and view the information.
WAAS 3D
1
2
3
Figure 12.4 - Celestial page
Refer to the image above. The time (1) displayed corresponds to the location of the crosshair cursor (3) in the Tide Graph (2). Moving the ShuttlePoint knob to the left or right changes
the time, moving the ShuttlePoint knob up or down selects the Tide height and draught
(draft) on the Tide Graph.
NOTE
The draught window shows the height of the tide water during a 24hr period of time. For example
if the ShuttlePoint knob is pressed up to move the cursor to the top of the Tide Graph this is the High
Water Level and if the cursor is moved to the bottom of the Tide Graph the draught will show the
Low Water Level.
CP190i and CPF190i
Page 97
Example 1
You anchor in 15Feet of water (under your keel) at a time of day where the water is the
highest (High Water). Let’s say the High Water window shows 5Feet and the Low Water
window shows 1Feet this means the water under your vessel over a 24 hour period of time
could fall 4Feet (High Water - Low Water). With your vessel in 15Feet of water and with a
maximum water change of 4Feet during the day, the worst case situation there will be
11Feet of water under your vessel.
12.5
GPS STATUS PAGE
This page is used as a reference to see how well the GPS is receiving satellites.
1
Ship’s Coordinates
2
Date and Time
3
WAAS/GPS Icon
4
Vertical Dilution of Precision
Horizontal Dilution of Precision
5
Tracked, but not used, Satellite
6
Used Satellite
7
COG (Course Over Ground)
1
WAAS
3D
3
4
2
5
A
6
14
5
28
6
20 C
D
31
25
7
E
B
Figure 12.5 - GPS Status page
The WAAS/GPS Icon area may change due to the satellite reception:
ACQUIRING
GPS2D
GPS3D
WAAS 2D/3D
HDOP
VDOP
:
:
:
:
:
:
the GPS is trying to receive a valid position fix.
The GPS is receiving at least 2 valid Satellites
the GPS is receiving at least 3 Satellites.
the GPS is receiving a 2D or 3D position and the correction from the WAAS Satellite.
Horizontal Dilution of Precision
Vertical Dilution of Precision
12.5.0 WAAS/EGNOS Setting
From this page it is possible to disable the WAAS/EGNOS function following this procedure:
1. Press [MENU], move the ShuttlePoint knob to enter GPS STATUS page and press
[ENT].
2. Press and hold [ENT]. The GPS SETUP menu appears on the screen.
3. Move the ShuttlePoint knob to highlight DIFF CORRECTION SOURCE and press
[ENT].
4. Move the ShuttlePoint knob to highlight None (to disable) and press [ENT].
5. Press [CLR] until the menu disappears or an easier method is to move the
ShuttlePoint knob to the left until the menu disappears.
Page 98
CP190i and CPF190i
12.5.1 Setup Menu
Off
On
INTERNAL GPS
RESTART GPS
NAVIGATION SPEED
NAVIGATION FILTER
High
DIFF CORRECTION SOURCE
WAAS/EGNOS
Figure 12.5.1 - Setup menu
From this page it is possible to activate the GPS Setup menu following this procedure:
1. Press [MENU], move the ShuttlePoint knob to enter GPS STATUS page and press
[ENT].
2. Press and hold [ENT]. The GPS SETUP menu appears on the screen. See the
following table:
Internal GPS
: Enables (On) or disables (Off) the Internal GPS. The default setting is On.
Restart GPS
: Restarts all GPS processes. Once executed, the message &quot;Done&quot; is shown.
Navigation Speed
: Allows setting the Navigation Speed among Low and High. The default setting is High.
Speed Filter
: Allows to resolve erratic speed readings in rough seas. Available values are Off, Low,
Medium, High. The default setting is Off.
Differential Correction Source : Allows setting what kind of Differential Correction will be used by the GPS between
WAAS-EGNOS and none. The default setting is WAAS-EGNOS.
3. Move the ShuttlePoint knob to highlight the preferred item and press [ENT].
4. Press [CLR] until the menu disappears or an easier method is to move the
ShuttlePoint knob to the left until the menu disappears.
12.6
NMEA DISPLAY PAGE
The GPS Chart Plotter is capable of displaying information in the customizable data
windows from external NMEA 0183 devices. Depth sounder, Speed Log with temp, Wind
speed and direction, Flux gate compass, and GPS information can be shown in any of the
boxes. The default NMEA Display shows 3 windows. When going to a destination, this
screen is useful to navigate as to get to the destination keep the Course Over Ground (COG)
and Bearing (BRG) figures the same.
Figure 12.6 - NMEA Display page
The NMEA sentences read from external devices are: BWC, DSC, DSE, GGA, GLL, GSA,
GSV, HDG, HDM, HDT, RMC, VHW, VTG, DPT, DBT, MTW, VWR, VWT, TLL, WPL, RTE.
CP190i and CPF190i
Page 99
Changing the NMEA Page Windows
1. Press [MENU], move the ShuttlePoint knob to highlight NMEA DISPLAY and press
[ENT].
Figure 12.6a - NMEA Display menu
2. Move the ShuttlePoint knob to highlight DISPLAY and press [ENT].
3. To change the 5 different pages move the ShuttlePoint knob to the left or right.
12.7
NMEA DATA PAGE
The NMEA Data page is very useful to see if a External device (example: Depth
Sounder) is transmitting NMEA sentences to the GPS Chart Plotter. This page can
also be used to see if the GPS Chart Plotter NMEA output is being loaded down by a
external NMEA device the GPS Chart Plotter is connected to.
Scenario: VHF Radio connected but the Radio is not receiving a GPS Position.
Usually the VHF Radio will be connected to the Green and Brown wires. To check to
see if the GPS Chart Plotter is transmitting the sentences:
1. Press [MENU], move the ShuttlePoint knob to highlight NMEA DISPLAY and
press [ENT].
Figure 12.7 - NMEA Display menu
2. Move the ShuttlePoint knob to highlight DATA and press [ENT].
3. Connect the BLUE Wire on the GPS Chart Plotter to the junction of the Brown wire
and the VHF wire. The display should look similar to the following picture.
Page 100
CP190i and CPF190i
Figure 12.7a - NMEA Data page
4. Press [ENT] to freese the data on the display so it is easy to read and understand.
5. Press [ENT] again to receive data again.
6. View data from a device connected to another data port, press the [ZOOM IN].
12.8
NMEA TREND PAGES
The CP190i* and CPF190i have the following NMEA Trend pages.
Trends will be shown for Depth, Temp and Speed (DST521 or DST526 must be connected
to show speed through the water) when a Standard Horizon transducer is connected. To
show Wind trend information the CP190i and CPF190i must be connected to the NMEA
output of a external Wind instrument.
NOTE*
The CP190i must be connected to the Optional FF525 (or FF520) 50/200kHz BLACK BOX FISH
FINDER.
To select a NMEA Trend Page:
1. Press [MENU], move the ShuttlePoint knob to highlight NMEA DISPLAY and press
[ENT].
Figure 12.8 - NMEA Display menu
2. Move the ShuttlePoint knob to select DEPTH TREND, WIND SPEED TREND, TEMP
TREND or SOG TREND and press [ENT].
CP190i and CPF190i
Page 101
17 5
18.5
18.
17.5
17
Figure 12.8a - NMEA Trend pages
12.9
VHF DIGITAL SELECTIVE CALLING
Digital Selective Calling is a semi-automated method of establishing a VHF radio call. DSC
had also been designated as part of the Global Maritime Distress and Safety System
(GMDSS).
This new system allow mariners to instantly send a distress call with GPS position (when
connected to the transceiver) to the US Coast Guard and other vessels within range of the
transmission. DSC will also allow mariners to initiate POSITION Request, POSITION
Report calls to or from another vessel equipped with a DSC transceiver.
Compatible VHF Marine Radios with Digital Selective Calling are able to be interfaced with
the GPS Chart Plotter which feeds GPS data to the VHF and listens for DSC calls from the
VHF. By connecting a few wires between the compatible DSC VHF radios and the GPS
Chart Plotter it will receive:
1. a vessel that has transmitted a DSC Distress call
2. a vessel that has transmitted a DSC Position Send Call
3. The position of a vessel that transmitted a DSC Position Request Call
12.9.0 Interfacing
To take advantage of these functions the GPS chart plotter must be interfaced (wired) to
a STANDARD HORIZON or compatible DSC VHF.
For additional information refer to Par. 2.4 Connections.
12.9.1 Distress Call
STANDARD HORIZON GPS chart plotters are able to display the location of a vessel in
distress when interfaced to a compatible DSC VHF with NMEA 0183 output and the radio
Page 102
CP190i and CPF190i
receives a DSC Distress Call. STANDARD HORIZON GPS chart plotter also log DSC
Distress calls to review at a later date.
1. Press [MENU] and move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight DSC Log and press [ENT].
03-03-10 MAN OVER
08:31 PM BOARD
33&deg;30.505 N
GO GO
0080457645 08:31 PM 118&deg;18.529 W
NO
03-04-10 ABANDONING ROY
33&deg;34.167 N
00:11 PM SHIP
0023244524 00:11 PM 118&deg;21.864 W YES
03-04-10
09:31 PM
SINKING
BOBI
33&deg;31.211 N
0056477743 09:31 PM 118&deg;29.151 W
NO
Figure 12.9.1 - DSC Log - Distress Call
12.9.2 Position Request
STANDARD HORIZON GPS chart plotters are able to display the location of a vessel when
connected DSC VHF radio and when a Position Request or Report call is received.
STANDARD HORIZON GPS also log DSC Distress calls to review at a later date.
1. Press [MENU] and move the ShuttlePoint knob to highlight USER POINTS and press
[ENT].
2. Move the ShuttlePoint knob to highlight DSC Log and press [ENT].
3. Move the ShuttlePoint knob to the right to select POSITION REQUEST and press
[ENT].
03-03-01
08:31 PM
33&deg;30.505
118&deg;18.529
N
W
0080457645
NO
03-04-01
00:11 PM
33&deg;34.167
118&deg;21.864
N
W
ROY
0023244524
YES
03-04-01
09:31 PM
33&deg;31.211
118&deg;29.151
N
W
BOBI
0056477743
NO
Figure 12.9.2 - DSC Log - Position Request
CP190i and CPF190i
Page 103
Page 104
CP190i and CPF190i
13. ADVANCED SETTINGS
The Advanced Setup menu allows customization of many GPS functions, Alarms and
NMEA interfacing.
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
While in this menu you will see many selections which are described in the next sections.
13.0
INPUT/OUTPUT (NMEA, AIS, RADAR)
13.0.0 Input
The CP190i has 2 Inputs and 3 Outputs connections. The CPF190i has 1 Input and 2
Outputs connections.
These ports may be set up to receive and output the following.
&middot; NMEA-0183 - NMEA devices* set to 4800 Baud (default setting)
&middot; Fish Finder: Only for CP190i: FF525 50/200kHz BLACK BOX FISH FINDER - refer to
Fish Finder Owner’s Manual
&middot; C-COM - C-Weather refer to Section 15
&middot; Radar - SI-TEX optional Radar refer to Radar Owner’s Manual
&middot; AIS38400 - AIS Receiver, refer to Section 14
&middot; MOBILARM - Mobil-arm receiver, refer to Section 16
&middot; Disabled - allow the port to be disabled.
NOTE*
RS232 not opto-isolated electrical interface.
NOTE
When a Port is configured, both the Input and Output have the same setting.
Port1 is set to Radar, both the Input and Output wires are set to SI-TEX proprietary Radar
sentences. This means other devices should not be connected to the Input or Output wires.
13.0.1 Ouput
The ports may be setup to output NMEA sentences. The table below shows the default
setting each port.
CP190i
Sentence
GLL
VTG
BWC
WCV
APA
Port1
On
Off
Off
Off
Off
CP190i and CPF190i
Port2
On
Off
Off
Off
Off
Port3
On
Off
Off
Off
On
Page 105
APB
HDG
BOD
XTE
RMA
RMB
RMC
GGA
HSC
DBT
DPT
MTW
VHW
GSA
GSV
Off
Off
Off
On
Off
Off
On
On
Off
On
On
On
On
On
On
Off
Off
Off
On
Off
Off
On
On
Off
Off
Off
Off
Off
Off
Off
Port1
On
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
On
On
Off
On
On
On
On
On
On
Port2
On
Off
Off
Off
On
On
Off
On
On
Off
Off
On
On
Off
Off
Off
Off
Off
Off
Off
On
Off
On
On
Off
Off
On
On
Off
Off
Off
Off
Off
Off
Off
CPF190i
Sentence
GLL
VTG
BWC
WCV
APA
APB
HDG
BOD
XTE
RMA
RMB
RMC
GGA
HSC
DBT
DPT
MTW
VHW
GSA
GSV
13.1
NAVIGATE
The Navigate Menu allows customization of the Coordinate System (Loran TD's), Chart
Datum, Chart Orientation Resolution (angle the vessel has to change before the chart is
redrawn) and Static Navigation. See the following table
Coordinate System
Chart Datum
Page 106
: Selections are:
a. TD: Time Difference, based on Loran (see the following Par. 13.1.0)
b. UTM: Universal Transverse Mercator Grid
c. ddd mm.mmm: Degrees Minutes and Thousands of Minutes
d. ddd mm.mm: Degrees Minutes and Hundredths of Minutes
e. ddd mm.ss: Degrees Minutes and Seconds (default)
: Allows selection of Chart Datums. The default Datum is WGS84 as C-MAP BY JEPPESEN
cartography has been compiled using the WGS84 Datum. A datum is a mathematical
model of the Earth which approximates the shape of the Earth, and enables calculations
such as position and area to be carried out in a consistent and accurate manner.
CP190i and CPF190i
Chart Orientation Resolution : Sets the angle the vessel has to change before the chart is redrawn. The default setting
is 30 degrees. Example: if the vessel is heading 000T at a speed of 25 Knots, the display
will redraw:
a. In Home mode the GPS Chart Plotter centers the location of the vessel in the center
of the display. To keep the vessel in the center of the display the GPS Chart Plotter
will occasionally redraw.
b. If the vessel changes course greater than 330T or more than 30T the chart will be
redrawn.
Static Navigation
: Sets up a threshold for the speed. When the speed received from the positioning device
is under that threshold, the GPS Chart Plotter displays zero. The default setting is 0.9 Kts.
13.1.0 Loran TD
The Loran TD selection allows the GPS Chart Plotter to be set up so the user can enter in
LORAN TD’s directly into the GPS Chart Plotter. After the TD’s have been entered, and the
user changes to ddd mm.sss (Degrees Minutes and Seconds) the TD’s will be converted
to Lat / Lon coordinates.
To use the TD Coordinate System the user must setup the Chain and Pair information of
the TD’s. If you do not know this information, refer to paper charts that show the Chain and
Pair information.
ASF1/2
: Additional Secondary phase Factor (TD Coordinate System)
Correction to TD1/2 values which can be inserted by the user to take in account the
additional signal propagation delay aver a mixed land/seawater path compared to on allseawater path. Normally the user does not enter a ASF value. However for experienced
users this function allows entering of signal delay values to fine adjust the calculated
position. The user should enter delay values to fine adjust the position calculated.
: Alternate Solution (TD Coordinate System)
Parameter selected by the user that is applied in the conversion of geographical coordinates
Lat/Lon to TD values. To be used if the position displayed is roughly not correct.
Alter
13.2
COMPASS
The GPS Chart Plotter computes compass direction from the constellation of GPS
Satellites. For the GPS Chart Plotter to compute direction the vessel must be moving
through the water unless connected to an optional Flux Gate Compass sensor. The
Compass menu allows the GPS Chart Plotter to customize the following selections:
Bearings
: Selects between True and Magnetic. When Magnetic bearings is enabled, the GPS Chart Plotter applies
the selected MagneticVariation (Auto or Manual, see next paragraph) to compute Magnetic bearing.
Variation : Allows the user to select Auto or Manual. When Auto mode is selected the GPS Chart Plotter computes
the ofset by the curent GPS fixed location. Manual mode allows the user to enter in a magnetic variation
that is applied in the True conversion.
Calibration : This function allows a user to enter in the offset for areas that the vessel may cruise instead of entering
in a manual offset for one location. This offset is useful for cruising vessels or vessels that travel
internationally often.
Figure 13.2 - Compass Table
13.3
ALARMS
The Alarms menu is used to select and setup audible and visual Alarms. Available alarms
are Arrival, XTE, Depth,Anchor and Grounding Alarm.
CP190i and CPF190i
Page 107
Arrival Alarm
: Alerts when the vessel is approaching single destination point or when arriving at a leg in
a Route. Available seletions: 0.00 to 9.99NM.
XTE Alarm
: Alerts when the vessel is deviating from a defined course. Available selections: 0.00 to
9.99NM.
Depth Alarm
: Alerts when the received depth Value is lower than the selected value. Available selections:
0000 to 3000FT.
Anchor Alarm
: Alerts when the ships moves off a selected locations by a selected distance. Available
selections: 0.00 to 9.99NM.
Audible Alarm
: Enables or disables the alarm beep.
Grounding Alarm
: This function looks ahead of the vessels heading to see if a potential danger exists. When
the Grounding Alarm is enabled the GPS Chart Plotter will draw a triangle in front of the vessel
on the Chart page showing the area that is being searched as shown below. The depth and
range (distance) of the area the GPS Chart Plotter looks ahead for a shallow area can be set
using this function.
Grounding Alarm Range : This function allows setting the distance of the grounding alarm zone (the length of the sector
to be detected) among the 0.25, 0.5, 1.0 Nm selections. When a depth or any of the searched
objects is found in the scanned area, a tick marker is printed on the relative box in the Grounding
Alarm Report page to identify which dangerous objects have been currently detected.
Grounding Alarm Report: This function allows displaying a report of the dangerous objects currently detected.
The following warning appears when the Grounding Alarm is enabled.
NOTES
The Grounding Alarm function is available only if a NT+/MAX C-CARD is inserted. It also affects the
screen redraw speed so we suggest to disable it when not used.
When any of the objects checked are found for the first time, the GPS Chart Plotter shows a pop
up window to alert the user of the possible danger. The name of each new dangerous object found
is reported in the warning window. In the Grounding Alarm Report page the relative item has a tick
marker next to it, to identify the dangerous object currently detected. If in the next search cycle the
same objects are found again, the alarm window will not be shown. Instead, if in the next searches
the objects found before are no longer detected, their relevant item in the Grounding Alarm Report
page is cleared (note that in this case, if the same object type is found again later, the Alarm will
be shown). The GPS Chart Plotter shows an icon on the charts that identifies when a Grounding
Alarm is detected.
Figure 13.3 - Grounding Alarm
13.4
SIMULATION
The built-in Simulator function allows you to become proficient in the use of the GPS Chart
Plotter, see the Simulation menu below:
Simulation Mode
Page 108
: Three selections:
a. Off - turn the simulation mode Off
b. On - enable the simulator mode, where the speed and course are adjusted by
entering in values in the Course and Speed selection discussed later in this table.
CP190i and CPF190i
Course
Speed
Date
Time
Cursor Control
Demo Mode
c. Route - this selection allows you to navigate to a saved route.
To start the simulator you can insert the Course value.
To start the simulator you can insert the Speed value.
To start the simulator you can insert the date.
To start the simulator you can insert the time.
Enables (On)/disables (Off) the cursor control. Moving the ShuttlePoint knob up or down will
change the SOG and left or right will change the COG of the simulated vessel.
: In Demo mode the GPS Chart Plotter automatically places a Destination point on the Chart
page and simulates navigation to the point. Also, the active page changes automatically
every 10 seconds. The pages are shown in the following order: Start-up screen, GPS Status,
Chart/Compass tape, Chart/Fish Finder, Full page Fish Finder, Full page Radar, Navigation, Highway, Celestial, NMEA. Once the Demo mode is enabled, pressing any key it is
possible to temporally exit and returns to GPS Chart Plotter normal operation, but if you do
not touch any key for 30 seconds Demo mode re-starts.
:
:
:
:
:
13.4.0 Navigating a Route in Simulation mode
This selection allows you to navigate to a saved Route to see how data windows on the Chart
page and how the Navigation and Highway pages operate.
1. Create a Route. Refer to Par. 9.0 Route.
2. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press
[ENT].
3. Move the ShuttlePoint knob down to highlight ADVANCED SETUP, then press [ENT].
4. Move the ShuttlePoint knob to highlight SIMULATION and press [ENT].
5. Move the ShuttlePoint knob to highlight SIMULATION MODE and press [ENT] to show
a popup window.
6. Move the ShuttlePoint knob to highlight ROUTE and press [ENT] which will show a
popup window with the Route(s) that are stored in the GPS Chart Plotter’s memory.
7. Highlight the desired Route and press [ENT].
8. Move the ShuttlePoint knob to highlight SPEED and press [ENT].
9. Enter in the speed you want to vessel to travel at in simulation mode, by moving the
ShuttlePoint knob left or right to select a number and up or down to change a number.
10. When the speed is adjusted, press [ENT].
11. Press [CLR] multiple times until the Chart Page is shown.
13.5
DSC POLLING
This menu is used to enable or disable features related to the DSC function.
Auto Position
Auto Info
: Selects between Manual or Auto. See also the Par. 12.8.1. When Auto Position item is set to
Manual and receiving the Position Request, the Position Request pop-up window is not displayed
and the cursor does not move to the position of the received Position Request data point.
Otherwise when Auto Position item is set to Auto, the GPS chart plotter works as follows:
1 : when receiving the Position Request, the Position Request popup window is displayed;
2 : when selecting VIEW ON CHART, the position is indicated on the chart marked with “P”.
The cursor is moved to the point “P” and shows the point in the center of the screen;
3 : when moving the cursor from “P”, the location can be confirmed. At this time, the same
MMSI Position Request data that were received before are remaining and displayed.
: Enables or disables the Auto Info. This selection is available only when Auto Position is set to
Manual. If Auto Info is set to On, when receiving the Position Request it is possible to center the
cursor over the top of the Position Request icon and show the Position Request popup window
CP190i and CPF190i
Page 109
Page 110
CP190i and CPF190i
14. AIS
AIS is an Automatic Identification System. It has been introduced to improve the safety of
navigation by assisting in the efficient operation of ship-to-ship location reporting and VTS
applications. The system should enable operators to obtain information from the ship
automatically, requiring a minimum of involvement of ship’s personnel, and should have a high
level of availability. AIS transponders installed on IMO vessels use VHF frequencies to:
&middot; Transmit details of their own vessel
&middot; Receive details from other vessels or navigation aids within VHF range.
STANDARD HORIZON GPS Chart Plotters are able to display AIS target (for collision
avoidance) on the Chart Page and AIS list pages when connected to a AIS receiver
(GX2100 or GX2150 STANDARD HORIZON VHF/AIS transceiver) or transponders which
output NMEA 0183 VDM sentence at 38400 or 4800 baud. The Chart Plotters are able to
show targets from both Class A (commercial) and Class B targets.
14.0
SYSTEM DEFINITIONS
&middot; Target: It is a vessel equipped with AIS. Information about the targets is being received
by AIS Receiver and displayed on the screen.
&middot; CPA : Closest Point of Approach is the closest distance that will be achieved between
your vessel and the tracked target, based on your vessel’s speed and direction and the
target’s speed and direction.
&middot; CPA Limit: This is the distance from your vessel that a target may reach before a target
is deemed a threat.
&middot; CPA Alarm: Occurs if CPA is less or equal to CPA Limit. This test is done for active
targets only.
&middot; TCPA: Time to closest Point of Approach is the time remaining until the CPA will occur.
&middot; TCPA Limit: This is the time remaining before the CPA is reached.
&middot; TCPA Alarm: Occurs if TCPA is less or equal to TCPA Limit. This test is done for active
targets only and if CPA value is less or equal to CPA Limit.
&middot; Radio Call Sign: International call sign assigned to vessel, often used on voice radio.
&middot; Name: Name of ship, 20 characters.
&middot; MMSI: Maritime Mobile Service Identity.
&middot; MMSI number: A unique 9 digit number that is assigned to a DSC radio station. It
primarily registers the boat information in the U.S. Coast Guard’s national distress
database for use in emergency situations.
&middot; Active Target: Target located within the Activation Range. Active target is represented
by oriented triangle with COG and Heading vectors. Rate of turn may also be displayed.
&middot; Dangerous Target: Target detected by CPA or TCPA Alarm. Dangerous target is
Active Target by definition. For better visibility Dangerous Target symbol is flashing.
&middot; Sleeping Target: Target located outside the Activation Range. Sleeping target is
represented by a small oriented triangle.
&middot; Lost Target: When the AIS info is not received from that vessel for 3.5 minutes. The
presentation will be a flashing black triangle with a cross through.
&middot; Activation Range: Range around your boat where targets become active. AIS target
CP190i and CPF190i
Page 111
become active within this range. Activation Range should be greater than CPA Limit
by definition.
NOTE
A target is removed from the screen if data is not received for 10 minutes.
The maximum number of tracked Class A or B targets is 200.
This information is updated every 3 seconds to 6 minutes depending on speed and rate of turn,
enabling the track of the vessels in range to be plotted.
Figure 14.0 - AIS Symbols
14.1
MENU
To configure the GPS Chart Plotter to receive AIS data, follow the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight AIS SETUP and press [ENT] or move the
ShuttlePoint knob to the right. The new AIS menu appears on the screen. The available
functions are described in the following table.
Display
: Turns the display of AIS Targets overlay on the cartography On or Off. The default setting is On.
Activation Range : Defines the range from the fix within which the AIS Target becomes active. The values allowed
are from 0.1 to 20 Nm. The default setting is 5 Nm.
CPA Alarm
: Turns On or Off the alarm. The default setting is On.
CPA Limit
: The values allowed are from 0.1 to 10 Nm. The default setting is 0.5 Nm.
TCPA Alarm
: Turns On or Off the alarm. The default setting is On.
TCPA Limit
: The values allowed are from 1 to 30 Min. The default setting is 10 Min.
14.2
AIS SETUP
Refer to Par. 2.4 for connections.
14.3
QUICK INFO ON AIS TARGET
By placing the cursor over a AIS Target icon using the ShuttlePoint knob, the following
information is displayed (see the following picture):
&middot; Vessel Name
&middot; MMSI number
&middot; Radio Call Sign
&middot; SOG
&middot; COG
&middot; CPA and TCPA values
Page 112
CP190i and CPF190i
Figure 14.3 - Quick Info on AIS
NOTE
The selected AIS Target icon is surrounded by a square frame when user places the cursor over
the icon.
14.4
LIST
It is possible to show the AIS List page that show basic information of the Target ship with
the ability to select a Target ship and locate it on the chart.
Follow the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight USER POINTS and press [ENT].
2. Move the ShuttlePoint knob to highlight AIS LIST and press [ENT].
Figure 14.4 - AIS List page
3. Move the ShuttlePoint knob up or down to select the Target and scroll the page up or
down. Press [ENTER] exits the page and shows the Target ship on the Chart page along
with the current position of the GPS Chart Plotter.
CP190i and CPF190i
Page 113
14.5
AIS TARGET COLORS
The received AIS Targets are shown in color. The color depicts the type of AIS ship shown
on the Chart Page. Refer to following table.
TYPE OF SHIP
GRAPHICAL PRESENTATION
Undefined
(yellow)
Fishing
(white)
Pleasure Craft
(light green)
Tanker
(dark blue)
Pilot Vessel
(light gray)
SAR
(black)
Tug
(pale green)
Port tenders
(brown)
Vessels with antipollution facilities or equipment
(light blu)
Low enforcement vessels
(light red)
Medical transport
(dark green)
Vessels according to Resolution N o 18 (Mob-83)
(cyan)
HSC
(red)
Passenger ship
(magenta)
Cargo ship
(dark gray)
Figure 14.5 - Color AIS Targets
Page 114
CP190i and CPF190i
15. C-WEATHER SERVICE
C-Weather is a free service available on the CP190i and CPF190i. C-Weather service gives
excellent coverage for the whole World. Weather forecasts are based on data received from
the leading meteorological centers. This data is processed by Jeppesen server and made
available via INTERNET connection to be transferred by using the C-Map BY JEPPESEN PCPlanner Windows Application. Then the weather data can be saved into a User C-CARD
to be loaded by the GPS Chart Plotter (see Par. 15.0.1).
Features: 5-day weather forecast updated every 6 hours; coverage of 180x180 Nm with
information frequency of 0.5&deg; Lat/Lon; wind direction and strength; wave height and
direction; ground temperature; level of humidity; visibility in miles.
Data Type
Display
WIND (Speed &amp; Dir)
0
WAVE Height &amp; Dir
1
TEMPERATURE
18&deg;
HUMIDITY (%)
30
VISIBILITY
20
WEATHER TYPE: Sun
WEATHER TYPE: Rain
WEATHER TYPE: Fog
WEATHER TYPE: Snow
WEATHER TYPE: Clouds
WEATHER TYPE: Partly Cloudy
WEATHER TYPE: Thunderstorm
Figure 15 - Weather data package
15.0
C-WEATHER SERVICE MENU
To select the menu:
1. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight C-WEATHER SERVICE and press [ENT] or
move the ShuttlePoint knob to the right.
The C-Weather menu is shown on the screen, the items are described in the following
paragraphs.
15.0.0 Download
Allows to connect the software to the weather server and to download weather data directly
via C-COM.
Select Country To Call : Allows the selection of the country to call. The whole telephone number set is automatically
updated after every download.
SIM Pin
: Allows inserting of the Pin of the SIM.
Download Area
: Allows the weather download: a squared grey area, where the weather data will be
downloaded, is centered on cursor position. See the following picture.
CP190i and CPF190i
Page 115
Area of coverage of
downloaded data is
located by default with
its center on the
cursor position
Cursor is locked to the
gray area.
Moving the cursor also
moves the gray area
allowing locating it
over the area where
the user wants to
download the forecast.
Indicates the LAT/LON
position of the cursor
Figure 15.0.0 - Example of Download Area
Press [ENT] to activate the C-Weather Download: the whole data package (see the
previous &quot;Weather data package&quot; table) are downloaded. [CLR] allows to interrupt the data
download. At the end of the operation press [CLR] to close the window.
15.0.1 Copy From User C-CARD
Allows the whole data package C-Weather loading from the User C-CARD.
15.0.2 Weather Forecast
Allows selecting the layer of specific weather data to be displayed on the screen and to
change date and time of the forecast preview. The following functions are available:
&middot; Panning: default usage of the cursor key is the normal panning function.
&middot; Zoom in/out: zoom in/out functions are allowed as usual by using [ZOOM IN]/[ZOOM
OUT].
&middot; Set of date and time: [GOTO] to modify date and time values.
&middot; Layer selection: [MENU] to cycle of the weather layers.
&middot; Exit: [CLR] to close the weather prediction page.
15.0.3 Real Time View
The following selections are available:
&middot; Real Time View On: the data is shown (the area of the download) at the current date
and time (received from the GPS).
&middot; Real Time View Off: the Weather data is not displayed.
The layer displayed is the one selected into the previous menu item.
15.0.4 Type of Data
Allows selecting the type of data, refer to the table in the Figure 15.
Page 116
CP190i and CPF190i
16. MOBILARM
The MOBILARM is an automated crew monitoring system dedicated to monitoring onboard
crew by maintaining a constant link between the crew member and the boat. When a man
over-board event happens, an automatic alarm is sounded, and the vessels position is shown
on the Standard Horizon GPS Chart Plotter.
16.0
MOBILARM-GPS CHART PLOTTER CONNECTION
Connect the MOBILARM system to one of the Ports on the Standard Horizon GPS Chart
Plotter. Refer to Par. 2.4.0 “Connection Table” for CP190i, Par. 2.4.2 “Connection Table”
for CPF190i and MOBILARM Owner’s Manuals for connections.
Connection Example
To Standard Horizon
GPS Chart Plotter
Blue
Brown
PWR ACC 1 Cable
Black
Green
Red
Figure 16.0 - Connection Example
CP190i and CPF190i
Page 117
NOTE
Note the CP190i and CPF190i have only one NMEA Input so Port1 will have to be set to
MOBILARM.
Port 1 Example
Chart Plotter
Blue
Brown
Red
Black
MOBILARM
NMEA Out
NMEA In
GPS V+
GPS V-
NOTE
Refer to the Figure 16.0, the Blue and Brown wires are from Port1. If these wires are being used
to connect to another NMEA device, choose another wire pair and configure the port associated
with the wires.
16.1
SOFTWARE SETUP
After the Port has been chosen and connected in Par. 16.0, the GPS Chart Plotter must be
setup to communicate with the MOBILARM.
Use the steps below to set up the Port the MOBILARM is connected to the GPS Chart
Plotter.
1. Select the Chart page.
2. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT].
3. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight IN/OUT CONNECTIONS and press [ENT] or
move the ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob to highlight any input port and press [ENT] or move the
ShuttlePoint knob to the right.
6. Move the ShuttlePoint knob up/down to select MOBILARM and press [ENT] or move
the ShuttlePoint knob to the right. Selecting MOBILARM format, activates the function.
7. Press [CLR] or move the ShuttlePoint knob to the left until the Chart Page is shown.
The GPS Chart Plotter continuously verifies the communication status with MOBILARM
PTX (Personal Transponder) device. When a signal from the PTX is lost for more than one
minute, the MOBILARM sends a NMEA message to the GPS Chart Plotter which will
produce an alarm and a popup window will be shown on Standard Horizon GPS Chart
Plotter.
16.2
MOBILARM STATUS
To confirm the status of the MOBILARM, select the About page:
1. Select the Chart Page.
2. Press [MENU] two times. Move the ShuttlePoint knob to highlight About... and press
[ENT].
On the About page you can see the status of the MOBILARM, below are the possible
messages.
a. Function not Activated : MOBILARM has not been setup in the I/O Connections
Page 118
CP190i and CPF190i
menu. Refer to Par. 16.1.
b. Not connected/detected : possible wiring problem, confirm wires are correct connected from the GPS Chart Plotter to the MOBILARM
device.
c. Connected
: the communication with MOBILARM device is Ok.
d. Signal Lost
: the MOBILARM has been connected in the past, however no signal is being detected from the MOBILARM.
Check wire connections from the GPS Chart Plotter to
the MOBILARM.
e. No valid GPS position
: the communication with MOBILARM device is Ok, but the
GPS position fix is not received from the GPS Chart
Plotter.
See the following example of About page:
1 MOBILARM status Information
XXXXXX
YY.YY
INTCHART 1
: WW-M012.03 MARINE FRESHWATER WWBK
BUILT-IN CHARTS: NA-Z010.00
: M-NA-M632.00 L. ANGELES and S. PEDRO BAYS
1
Designed for
Figure 16.2 - Example of About page with MOBILARM information
16.3
MOBILARM PTX
A PTX is the Personal Transponder device that is worn by the crew. If a crew member falls
in the water the MOBILARM sends a signal to the GPS Chart Plotter which creates and
displays a PTX icon on the Chart Page.
16.3.0 MOBILARM MOB alert is received
When crew member falls in the water, the MOBILARM sends a signal to the GPS Chart
Plotter which creates and displays a PTX MOB icon on the Chart Page.
Figure 16.3.0 - The PTX icon
On the GPS Chart Plotter all menus and/or pages are closed and the chart is centered on
the PTX MOB received position. A Audible Alarm is heard and a pop-up warning window
appears to notify that a PTX has been received:
CP190i and CPF190i
Page 119
Figure 16.3.0a - Example of PTX warning window
It is possible to Goto (navigate) to the received MOBILARM PTX position (see Par. 16.4.1)
or open the MOBILARM Alarm Status List page (see Par. 16.4.2). Selecting Goto or Alarm
Status List will mute the Audible Alarm.
NOTE
When the same PTX is received again:
a. If the received PTX is not the active one, the user must confirm to navigate to it.
b. If the received PTX is the active one, navigation data is updated. The PTX icon appears at the
new position and a pop-up warning window appears.
16.4
PLACING CURSOR ON THE PTX ICON
Moving the ShuttlePoint knob so the cursor is over the PTX icon on the Chart page will show
an information window and allow you to Goto the location of the PTX, delete the PTX icon
or show the Alarm Status list as shown below.
Figure 16.4 - Example of PTX information window
16.4.0 Delete PTX
The Delete PTX function permamently removes the selected PTX from the MOBILARM
Alarm Status List and from the Chart Page.
Using the ShuttlePoint knob, move the cursor over the PTX icon and then press [ENT],
select DELETE using the ShuttlePoint knob and press [ENT]. A warning pop-up window will
be shown. Select YES and press [ENT].
16.4.1 Goto PTX
When Goto is selected on the GPS Chart Plotter, navigation will start to the PTX icon
location. After the GPS Chart Plotter has received a PTX MOB alarm, using the ShuttlePoint
Page 120
CP190i and CPF190i
knob move the cursor over the PTX to navigate to and then press [ENT], select GOTO using
the ShuttlePoint knob and press [ENT].
Figure 16.4.1 - Example of Goto PTX
If the navigation is set to the selected PTX icon, to terminate the navigation press [ENT],
select STOP GOTO using the ShuttlePoint knob and press [ENT].
Figure 16.4.1a - Example of Stop Goto PTX
16.4.2 The MOBILARM Alarm Status List
The MOBILARM Alarm Status List shows the list of all PTX that the GPS Chart Plotter has
received an alarm from. To review the page:
1. Select the Chart Page.
2. Press [MENU] to show the Main menu.
3. Move the ShuttlePoint knob to highlight USER POINTS and press [ENT].
4. Move the ShuttlePoint knob to highlight MOBILARM and press [ENT].
1 PTX number
2
1
Time the PTX alarm was received
Recovered
03:45:14 PM
213&deg;22.120W
20&deg;01.022N
Recovered
10:31:24 PM
305&deg;04.015W
79&deg;56.320N
Recovered
2
3 PTX position
4 PTX status
3
4
Figure 16.4.2 - Example of MOBilarm PTX List page
CP190i and CPF190i
Page 121
This page allows you to:
GOTO
DELETE
SHOW
SHOW ALL
Activates navigation to the selected PTX. Once the navigation has been activated, close all
menus/data pages (if open) and center the chart selected PTX.
Deletes the selected PTX.
Centers the chart on the selected PTX.
Selects the best chart scale to see al PTX icons on the chart at the same time.
Page 122
CP190i and CPF190i
17. FISH FINDER
FOR
CPF190i
The Fish Finder consists of a high power transmitter, sensitive receiver and a transducer.
The Fish Finder sends an electrical pulse to the transducer, which contains an element that
converts the pulse into acoustic (sound) waves, which is sent through the water. As this
wave travels from the transducer to the bottom, it may strike fish, structures, thermalclines
(temperature changes in the water). When the wave strikes an object(s) a certain amount
of the wave is reflected back to the transducer depending on the composition and shape of
the object. When the reflected wave is returned to the transducer it is converted into a
voltage and is amplified by the receiver, processed and sent to the display. The speed of
sound in water is roughly 4800FT/sec, so the time lapse between the transmitted signal and
the received echo can be measured and the distance to the object determined.
Figure 17 - Fish Finder working principle
17.0
ENABLE/DISABLE
The internal Fish Finder may be enabled (default setting) or disabled by the following
procedure:
1. From the Chart Page, press [MENU], move the ShuttlePoint knob to highlight SETUP
MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight IN/OUT CONNECTIONS and press [ENT] or
move the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight FISH FINDER and press [ENT] or move the
ShuttlePoint knob to the right.
CP190i and CPF190i
Page 123
5. Move the ShuttlePoint knob up/down to select OFF and press [ENT] or move the
ShuttlePoint knob to the right.
6. Press [CLR] or move the ShuttlePoint knob to the left until the Chart Page is shown.
17.1
UNDERSTANDING THE FISH FINDER PAGE
The display on CPF190i shows a time history of the echoes received by the transducer. The
CPF190i has a menu that allows adjustments to receiver sensitivity, depth range and
scrolling speed of the Fish Finder display.
1
Warning message
2
Fish Finder window
3
Digital Depth
4
Water temperature
5
Shallow Alarm Bar
1
6
Range Bar
2
7
Variable Depth Marker (VDM)
8
A-Scope
9
Deep Alarm Bar
10
5
6
7
8
9
3
10
4
Transmit Frequency
Figure 17.1 - The Fish Finder page
The following is a brief description of terms listed in the previous Figure:
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
&middot;
Warning Message
Flashing label that is turned On when the echo sounder is in Simulation mode.
The following is the list of the warning messages (see also Par. 5.8):
SHALLOW WATER
DEEP WATER
HIGH WATER TEMP
LOW WATER TEMP
WATER TEMP RATE
FISH SPOT
NO DATA
Fish Finder window
Graphic presentation of sonar soundings recorded as a continuous profile scrolling
across the screen from right to left. Such recordings represent the image of the water
beneath your boat, items appear as they pass under your transducer; the items on the
right side of the screen are closer to you than those on the left. The correct interpretation
of the Fish Finder page allows retrieving useful information about what is under the
boat.
Digital Depth
Readout of the current bottom depth.
Water Temperature
Readout of the current water temperature returned by the temperature sensor included
in DST520, DST521, DST523, DST525, DST526, DST527, DST528A.
Page 124
CP190i and CPF190i
Shallow Alarm Bar
Located on the right side of the Range Bar, the Shallow Alarm Bar shows the range
outside of which the depth measurement will trigger a Shallow Alarm.
Range Bar
Vertical graduated bar that is located along the right side of the screen. It is a scale
which reflects the depth of the area being displayed.
Variable Depth Marker (VDM)
Horizontal line on to the Fish Finder page window with a depth label. Move the
ShuttlePoint knob Up or Down to change the position of the VDM. The label displays
the depth of the cursor position. The VDM can be moved to any location pinpointing the
depth of a target.
A-Scope
Real time representation of fish and bottom features passing through the beam of the
transducer, drawn as column of horizontal lines whose length and hue is proportional
to the echo strength returned. The color of the echo strength depends on the selected
display color. When the default palette is selected, the strongest sonar returns will be
shown as red and weaker returns will be shown blue.
Deep Alarm Bar
Bar located on the left side of the Range Bar, showing the portion of the Echogram
currently represented in the zoomed window (on the left part of the screen). It is turned
On selecting the Echosounder Split page.
Transmit Frequency
Shows the selected depth transmit frequency. As a reference, 200kHz selection is
normally used to see targets in depth up to 400FT, and 50kHz is used in water over
400FT.
17.1.1 Understanding the Fish Finder display
1
1
Fish
2
Thermoclines
3
White Line
4
Surface Clutter
2
5
Structures
3
6
Bottom Echo Profile
4
5
6
Figure 17.1.1 - The Fish Finder display
Fish
Fish are usually represented by small dots on the display when using 200kHz and by
arches when using 50kHz.
Thermoclines
Are the zones where two layers of different water temperatures meet. The greater the
temperature differential, the denser the thermocline shows on the screen. Thermoclines are represented as horizontal stripes of noise. They are very important for fishing
since often many species of game fish like to suspend in, just above, or just below the
thermoclines.
CP190i and CPF190i
Page 125
White Line
The White Line shows the difference between hard, soft bottoms and even distinguishes between fishes and structures located near the bottom. In this way it is easier to tell
the difference between a hard and soft bottom and even to distinguish fishes and
structures located nearby the bottom.
Surface Clutter
Appears like noise at the top of the screen extending many feet below the surface. It’s
caused by many things, including air bubbles, bait fish, plankton and algae.
Structures
Generally, the term “structure” is used to identify objects like wrecks and weeds rising
from the bottom.
Bottom Echo Profile
Bottom profile recorded by the Fish Finder. When the echo sounder is set in Auto
Range mode, the bottom is kept in the lower half in the display.
17.2
DISPLAYING THE FISH FINDER PAGE
This section explains how to show and customize the selection of the Fish Finder display
pages.
1. From all pages (except the Fish Finder page), press [MENU].
From Fish Finder page, press [MENU] two times.
Figure 17.2 - Main Menu
2. Move the ShuttlePoint knob to highlight RADAR/FISH and press [ENT].
Figure 17.2a - Fish Finder page selection menu
Page 126
CP190i and CPF190i
3. Move the ShuttlePoint knob to select the desired display and press [ENT]. The Page
options are shown in the following paragraphs.
17.2.0 Auto Full Page
When this page is selected, the Fish Finder automatically changes the transmit frequency
to show depths. Automatic switching occurs when depth of water is less than 400FT
(200kHz) and greater than 400FT (50kHz).
17.2.1 200 kHz Full, 50 kHz Full and 50&amp;200kHz Display Pages
Allows the user to setup the GPS Chart Plotter display to show 200kHz, 50kHz or 200/50
kHz split screen Fish Finder.
200kHz
50kHz
50/200kHz
Figure 17.2.1 - Full Display pages
17.2.2 200 kHz and 50 kHz Zoom Pages
Allows the user to zoom into the 200kHz or 50kHz Fish Finder display to show detail of the
area selected by the VRM (Variable Range Marker). Referring to Figure 17.2.2, the left
display shows the zoomed display and the right display shown the unzoomed display.
To select the area to be zoomed in move the ShuttlePoint knob Up or Down which moves
the VRM line.
To zoom In or Out, press [ZOOM IN] or [ZOOM OUT].
The zoom ranges are 2x and 4x the normal Fish Finder display.
30.0Ft
Figure 17.2.2 - Zoom Full page
CP190i and CPF190i
Page 127
17.2.3 200 kHz and 50 kHz Fish/Chart Pages
Selects the GPS Chart Plotter display to show the Chart page on the left half of the screen
and the Fish Finder on the right half of the screen. 200kHz or 50 kHz Fish Finder can be
selected on the right half of the display.
Figure 17.2.3 - Fish/Chart page
When the Fish/Chart Page has been selected use [FIND] to place the focus on the Chart
Page or on the Fish Finder window.
With the focus on the Chart Page the cursor may be moved and all chart menus can be
selected. When focus is on the Fish Finder window the Variable Range Marker can be
moved to see the depths of targets and Fish Finder menus can be accessed.
17.3
SETUP MENU
This section explains how to show the Fish Finder Setup menu and describe the Fish Finder
Setup menu sub-options.
1. From the Full Fish Finder page, press [MENU]. The following menu appears:
Figure 17.3 - Fish Finder Setup menu
17.4
FISH FINDER COLOR
Allows you to choose the Fish Finder color between 16 and 256 colors.
Page 128
CP190i and CPF190i
Figure 17.4 - Fish Finder Color menu
17.5
PRESETS
To simply menu selections, the Fish Finder has two presets that can be easily selected for
Fishing or Cruising:
Gain
Range mode
Gain offset
Shift
STC
FISH
Auto
Auto
0%
0
Short
CRUISE
Auto
Auto
10%
0
Short
Noise level
Scrolling Speed
Fish Symbols
A-Scope
Surface Declutter
2
10
Echo
On
4
4
10
Echo
On
4
Figure 17.5 - Presets table
NOTE
For Gain and Gain Offset settings refer to Sensitivity menu (see Par. 17.10).
For Range and Shift settings refer to Range menu (see Par. 17.8).
17.6
FREQUENCY
Allows you to choose the frequency among Auto, 50 kHz, 200 kHz or 50&amp;200 kHz when
single frequency page is selected.
Figure 17.6 - Frequency menu
CP190i and CPF190i
Page 129
17.7
GAIN MODE
Figure 17.7 - Gain Mode menu
17.7.0 Auto Mode
Allows the Fish Finder to automatically adjust receiver Gain depending on water depth.
17.7.1 Manual Mode
Allows the user to change the Gain manually to fine tune the Fish Finder’s receiver.
17.8
RANGE MENU
Figure 17.8 - Range menu
17.8.0 Range Mode
Selects among Manual, Auto Range and Bottom Lock.
17.8.0.0
Manual Mode
Used to set the depth Range (from the surface) the Fish Finder display will show.
17.8.0.1
Auto Range
The Fish Finder determines automatically the Range as to keep the bottom visible in the
lower bottom of the screen. In this mode, Shift is always set to 0.
17.8.0.2
Bottom Lock
The Bottom Lock function keeps the screen display locked onto a certain Range around the
Page 130
CP190i and CPF190i
bottom. Let’s say the bottom is 400FT and the Bottom Lock Range is set to display 30FT
around the bottom, the screen (instead of displaying from 0FT to e.g. 450FT) will display only
a Range of 30FT around the bottom, e.g. from 380FT to 410FT.
17.8.1 Depth
Moves the display from showing the bottom to the depth value entered.
17.8.2 Shift
Shifts the display from the bottom of the transducer to the depth value entered.
Example: Your vessel is in about 57FT of water, however there is fish suspended in 35FT
of water. You want to display to 10FT area around the fish. Shift would be set
to 30FT and Depth would be set to 40FT shown in example below.
30
Top of display
Shift = 30Ft
35
40
Bottom of display
Depth = 40Ft
Figure 17.8.2 - Example of Depth and Shift
17.9
INTERFERENCE REJECTION
Figure 17.8 - Interference Rejection menu
Turns On or Off a filter to remove noise from other Fish Finder or Depth Sounders that may
be near by when fishing.
17.10 SENSITIVITY MENU
All settings in the Sensitivity menu are related to the selected Fish Finder transmit frequency
(50 or 200kHz).
CP190i and CPF190i
Page 131
Figure 17.10 - Sensitivity menu
17.10.0
Gain
Allows you to control the Sensitivity of the unit’s receiver from 0 to 100%. To see more detail,
increase the receiver Sensitivity by selecting a higher Gain percentage. If there is too much
detail or if the screen is cluttered, lowering the Sensitivity may increase the clarity of the
display.
NOTE
When the Gain Mode option is set to Auto, the receivers Gain cannot be changed.
When the Gain Mode option is set to Manual, the Gain can be manually adjusted. When switching
from Automatic to Manual Mode, the Gain + Offset value is copied into the Manual Gain setting of
the receiver.
17.10.1
STC (Sensitivity Time Control)
The STC function attenuates echos from surface down to the specified STC depth by
changing the sensitivity of the receiver, decreasing it near the surface and gradually
increasing it as the depth increases.
STC impacts bottom finding so can be particularly useful i.e. to better track a rock sea
bottom distinguishing it from the mud in suspension over it for example when close to rivers
outlet to the sea (consider to use at same time also Dual Frequency mode and White Line
for an easier identification of real sea bottom), as well as to solve issues in false bottom
detection when in presense of significant surface clutter.
Its default value is SHORT for the 200 kHz frequency and MID for the 50 KHz frequency.
Such values are good in most conditions. However when navigating in very shallow waters
it may be necessary to switch it to OFF, while in very deep waters with a lot of Surface Clutter
it may be better to increase it to MID or LONG.
NOTE
In some situations it may be necessary to adjust the STC so the sounder can read through the
surface noise and show the bottom. One indication that the STC needs to be changed is when the
display intermittently changes the depth from the correct depth to a very shallow depth.
Figure 17.10.1 - STC - Surface Clutter
The STC can be changed from Short, Mid, Long and Custom.
Page 132
CP190i and CPF190i
17.10.1.0
STC Length
This is the depth range which the STC operates. In custom mode it can be varied from 0FT
to 1000FT (60FT or 255FT on previous software versions). In preset mode it’s value is
reported in the following table (See Par. 17.9.1.2).
17.10.1.1
STC Strength
It is the starting attenuation value of the STC. It acts by attenuating the Gain of the given
percentage value. In custom mode it can be varied from 0% to 100%. The STC effect is
maximum near the surface, to mitigate the Surface Clutter and it progressively diminishes
to 0 at the selected STC depth.
17.10.1.2
Preset values table
STC Depth (Ft)
STC Length
OFF
1
0
Short
60
10%
Mid
60
30%
Long
255
57%
Figure 17.10.1.2 - STC Preset values table
If in VERY SHALLOW WATER the Fish Finder display is showing a bottom or digital
readout deeper than the actual depth this situation may occur if STC is set to LONG or
MID when the bottom is shallow. This issue may be resolved by adjusting the STC value
to SHORT or even to OFF in very shallow waters.
If in DEEP WATER the Fish Finder display is showing a very shallow bottom or digital
readout this may happen because in conditions of strong Surface Clutter the Fish Finder
may erroneously look on to the Surface Clutter. To solve this situation try to increase the
STC to LONG or to CUSTOM increasing the STC length and strength.
If in DEEP WATER the Fish Finder doesn’t see the bottom, this may happen because the
bottom is out of range or is very near to the maximum depth that can be tracked by the
Fish Finder. In the latter case this may happen if the bottom composition is soft as mud,
if the sea conditions are bad, there are thermoclines or the water is full of suspended
materials (silt, plankton). All these factors may affect considerably the performance of the
Fish Finder to be able to see the bottom. In these cases change the RANGE MODE from
AUTO to MANUAL Range and manually adjust the depth range until the bottom echo
becomes visible on the Fish Finder display.
17.10.2
Surface Noise Filter
An automatic filter that attempts to dynamically remove Surface Clutter that causes the
screen to be filled up with strong return echoes just below the surface. It may seem that
the same functionality could be archived using on the STC control however there is main
difference between such control in fact the STC control impacts the capability to detect
and track the bottom and is not designed to cancel completely the surface noise, on the
other side the Surface Noise Filter attempts to cancel completely the surface noise but it
doesn’t affect the capability to detect and track the bottom.
Filter gradually attenuates surface noises. The Surface Noise Filter has 9 settings: OFF, 1,
..., 8. When it is set to OFF the Surface Noise is not cancelled. When it is set to 1 the Surface
Noise is attenuated from surface down to a depth of 5 Ft, increasing the Surface Noise
increases the depth in which the Surface Noise is attenuated as well as the attenuation level
increases; when the preset is set to 8 the attenuation is maximum and is applied from
surface level down to a depth of 255 Ft, as shown in the Surface Noise Filter Table reported:
CP190i and CPF190i
Page 133
Surface Noise Filter Depth
Preset
1
Depth (Ft)
5
2
10
3
15
4
20
5
30
6
60
7
130
8
255
Figure 17.10.2 - Surface Noise Filter Depth table
17.11 DISPLAY SETUP
Allows the Fish Finder’s display page appearance to be changed.
Figure 17.11 - Display Setup menu
17.11.0
Color Settings
Allows you to change the color of the Fish Finder display from Blue (default), White, Black,
Gray scale.
Figure 17.11.0 - White and Blue background examples
17.11.1
Scrolling Speed
Controls the rate the Fish Finder scrolls and updates the Fish Finder display.
17.11.2
White Line
Controls how the bottom type (hard or soft) is shown on the display. When the White Line
is Off the bottom return will display as red. When the White Line is On it can be used to
determine bottom hardness.
NOTE
The White Line option is not available in the 50 &amp; 200 kHz page.
Page 134
CP190i and CPF190i
17.11.3
Fish Symbols
Controls the graphical representation of underwater-suspended targets.
Echo
: shown as arches (echoes)
Icon + Echo
: shown as arches with the Fish icon
Icon + Echo + Depth : shown as arches with the Fish icon and relative depth values
Echo + Depth
: shown depth values
Icon
: shown as Fish icons without the arches
Icon + Depth
: shown as Fish icons and their relative depth values (shown accordingly to currently selected depth unit)
17.11.4
A-Scope
Shows the real time display of the echo from the bottom.
17.12 TRANSDUCER SETUP
This menu allows you to calibrate the speed through the water, water temperature and the
keel/prop offset of the transducer.
Figure 17.12 - Transducer Setup menu
17.12.0
Keel Offset
The keel offset can be set to cause the Fish Finder to display an offset depth below the keel
or the actual water depth from the surface. To setup to show the depth below the keel, enter
a negative depth value or a positive depth to show offset from the transducers face to the
water surface.
17.12.1
Calibrate Water Speed
Used to calibrate the Water Speed readings from the transducer. Adjustment can be made
from -10% to +10%.
17.12.2
Calibrate Water Temp
Used to calibration on the Water Temperature sensor in the transducer.
17.12.3
Set Defaults
Restores the factory settings.
CP190i and CPF190i
Page 135
17.13 ALARMS
The Alarms menu allows you to define alarm settings for Shallow Alarm, Depth Alarm and
Temperature Upper/Lower/Rate.
Figure 17.13 - Alarms menu
To set an Anchor Alarm, enter in a shallow water and deep water value above and below
your actual anchoring depth. The alarm will sound when the depth becomes shallower or
deeper than the settings.
17.13.0
Shallow Water
Triggers an alarm when depth becomes shallower than the set depth.
17.13.1
Deep Water
Triggers an alarm when depth becomes deeper than the set depth.
17.13.2
Fish
The Fish Alarm can be set to detect and alert you depending on the size of fish. The options
are: Off, Small, Medium, Big and Huge. The alarm sounds if the set size (or bigger) is
detected.
17.13.3
Temperature Upper
Triggers an alarm when the transducer reports a temperature above the set temperature.
17.13.4
Temperature Lower
Triggers an alarm when the transducer reports a temperature below the set temperature.
17.13.5
Temperature Rate
Triggers an alarm when the transducer reports a temperature variation rate above the set
temperature.
Page 136
CP190i and CPF190i
17.14 SAVE SETTINGS TO USER C-CARD
This option saves the complete set of Fish Finder settings to an optional User C-CARD. This
is useful to avoid the user having to retune up Fish Finder after a RAM Clear operation or
a software update.
Figure 17.14 - C-CARD - Save settings
17.15 LOAD SETTINGS FROM USER C-CARD
This option loads the complete set of Fish Finder settings from the User C-CARD (Memory
Card that may be used to backup the User Points and Tracks too).
Figure 17.15 - C-CARD - Load settings
17.16 RESTORE CURRENT PRESET DEFAULTS
This option restores the default values only for the current presets and does not affect the
other presets.
Figure 17.16 - C-Card - Restore settings
CP190i and CPF190i
Page 137
Page 138
CP190i and CPF190i
18. TROUBLESHOOTING
The GPS Chart Plotter does not turn On. The voltage or the polarity may not be correct.
Make sure that the correct voltage (10-35 volt dc) is present. Check also that the polarity
is correct.
The GPS Chart Plotter does not get a valid fix. The external WAAS GPS antenna may
not be in a open sky position or the antenna cable may not be properly connected. Make
sure that no metal obstacle (solar panel about the plotter) is placed around the chart plotter
(or external antenna when connected) acting as a shield for the antenna and disconnect and
connect again the antenna cable to the GPS Chart Plotter. If, after 15 minutes, the GPS
Chart Plotter does not get the fix, turn it Off and On again.
The GPS Chart Plotter does not turn Off. The GPS Chart Plotter may be in an
unpredictable status. If, after pressing [PWR] (for at least 3 seconds) the GPS Chart Plotter
does not turn Off, turn Off the voltage.
The GPS Chart Plotter screen becomes very dark after a long exposure to direct
sunlight. The internal temperature is very high. Protect the GPS Chart Plotter from direct
sunlight.
The GPS Chart Plotter does not respond to any command. The GPS Chart Plotter may
be in an unpredictable status. Try to turn Off, and then turn On. If the problem persists, reset
the RAM or remove power from the battery.
The location of my fix is not shown correctly on the Chart page. Please report to C-Map
USA (800/424-2627) the Latitude &amp; Longitude of your vessels position, the position where
you think your vessels should be and details of the cartography such as “Compilation scale”,
“Notice to mariners” and “Horizontal datum” (which can be seen by selecting the Chart
Page, press [FIND], move the ShuttlePoint knob to Data Source and press [ENT]).
After storing the Chart Plotter over the winter, It takes a long time to receive a fix.
This is usually caused by the internal rechargeable memory battery from becoming low
which could cause the Internal RAM memory to become corrupted. To solve this issue,
perform a RAM clear (refer to Section 19).
NOTE
After performing a RAM Clear all Marks, Routes and tracks will be erased. To back up these points
refer to Section 11 for details.
CP190i and CPF190i
Page 139
Page 140
CP190i and CPF190i
19. TECHNICAL TESTS
19.0
SYSTEM TEST
If you have connected your GPS Chart Plotter according to the instructions, and chosen the
proper menu selection for your device, and are still having problems with your GPS Chart
Plotter, the extended auto-test should help determine the problem. Make sure the GPS
Chart Plotter is turned Off. While pressing and holding any other key, turn the GPS Chart
Plotter On. A new menu will appear on the display:
Figure 19.0 - System Test
Use the ShuttlePoint knob to select the desired test. Choose the test, press [ENT]. To exit
from any submenu press [CLR]. To exit from the System Test turn Off the GPS Chart Plotter.
19.0.0 RAM Menu (reset)
This test verifies the integrity of the memories and if desired during this test all the internal
memory can be erased and the default setting restored.
RAM Clear
To clear internal memory. If the GPS Chart Plotter exhibits unusual operations, or appears
to be malfunctioning, it may be possible to correct the problem by clearing RAM.
This operation will erase all Marks, Routes, stored Track plots and Destinations. It will also
return all selections (Input Data Format, Autopilot selection, etc.) to original default values.
To confirm clear RAM press [ENT] again (but if at this time you do not wish to clear RAM
press [CLR]).
19.0.1 DIM Menu
To select the desired value for brightness and keypad light.
Contrast
Each time you move the ShuttlePoint knob to right, the screen will decrease brightness,
move it to the left to increase brightness.
Backlight
The second option allows to set the backlight. Operates in similar mode as Contrast.
CP190i and CPF190i
Page 141
19.0.2 Cartridges
To check the C-CARD and its connector.
Internal Data Base Test
To test the Worldwide background.
C-CARD Test
To test the C-CARD. There are the possible situations:
1. if there is a C-CARD inserted in the slot and there is not a malfunction, the name of the
C-CARD zone and the message &quot;OK&quot; are shown.
2. if there is a C-CARD inserted in the slot, but it is a defective C-CARD, the name of the
C-CARD zone and the message &quot;Faulty&quot; are shown.
3. if there is not any C-CARD inserted in the slot, the message &quot;not present&quot; is shown.
4. if there is a User C-CARD inserted in the slot, the message USER C-CARD is shown.
C-CARD Connector
Indicates if there is a malfunction in the connector.
19.0.3 Serial Ports
If you are having problems receiving data from the position-finding instrument, this test
should help determine the problem.
Change Parameters
To change the parameters of the serial interface. This menu allows to select the Port (Signal
Source) between PORT 1, PORT 2, PORT 3; the Baud Rate between 300, 1200, 2400,
4800, 9600, 38400, 115200; the Data Bits (Word Length) between 7 or 8, the Parity
between even, odd or none, the Stop Bits between 1 or 2. Default settings are: Port = PORT
2, Baud Rate = 4800, Data Bits = 8, Parity = none, Stop Bits = 1.
Input Data Display
To allow the GPS Chart Plotter to act as a computer terminal and display the incoming data
exactly as it is received.
If the data displayed on the screen are unrecognizable, you may have selected the wrong
input parameters for your particular receiver, for example, Baud Rate 9600 instead of Baud
Rate 4800. Check your receiver manual to be sure that you have selected the proper
parameter. If the screen is blank, you may have a broken connection, and no data is being
received or you may have connected the device to the other input port.
Use [ZOOM IN] to stop (or continue after pause) data displaying, [ENT] to show data in hex
or ASCII mode (normal or small) and [CLR] to exit.
Loop-Back Test
This is a special test done during the production phase to check the serial ports integrity.
This function is only required by Standard Horizon.
Page 142
CP190i and CPF190i
20. SPECIFICATIONS
20.0
CP190i/CPF190i SPECIFICATIONS
Power Consumption Max Backlight :
:
Power supply
:
Interface
:
Display
:
Display Resolution
:
Cartography
:
Operating temperature range
:
Storage temperature
:
Water Resistance
:
Memory
:
Keyboard
:
Weight (without bracket)
:
User Points (Marks/Waypoints)
:
Routes
:
Track Points
:
NMEA Output sentences
:
NMEA Input sentences
20.1
CP190i = 0.5A@12VDC
CPF190i = 1.3A@12VDC
10-35 Volt DC
Input/Output Interface NMEA-0183
TFT Color LCD (active area 5&quot;) sunviewable technology
320 x 232 pixels
C-MAP BY JEPPESEN NT+/MAX C-CARD
32&deg;F/+131&deg;F (0&deg;C/+55&deg;C)
-4&deg;F/+158&deg;F (-20&deg;C/+70&deg;C)
splash-proof
Permanent
Silicon rubber, backlight
1,655 lb (750 g)
3000
50 (max 100 Waypoints each)
10000 (recordable in 20 Tracks)
GLL, VTG, BWC, WCV, APA, APB, HTG, BOD,
XTE, RMA, RMB, RMC, GGA, HSC, DBT, DPT,
MTW, VHW, WPL, RTE, GSA, GSV
: BWC, DSC, DSE, GGA, GLL, GSA, GSV, HDG,
HDM, HDT, RMC, VHW, VTG, DPT, DBT, MTW,
VWR, VWT, TLL, WPL, RTE
CPF190i FISH FINDER SPECIFICATIONS
Power Output
: 600W
Frequency
: 50 and 200kHz
Minimum Depth
: 5Feet at 50kHz, 2.5Feet at 200kHz
Maximum Depth
: 1500Feet at 50kHz, 700Feet at 200kHz
Airmar X-DUCER ID
: Must use Standard Horizon transducers
Advanced Digital Signal Processing
Speed &amp; Temperature Sensor (if available on transducer)
Alarms (shallow water, depth, Fish, temp)
Trip Log, Fish Symbols
STC, Interference Rejection, Automatic noise reduction
A-Scope, White Line, Zoom x2/x4
Auto range/gain/frequency/shift/ping rate
16/256 colors display user selectable
CP190i and CPF190i
Page 143
CP190I/CPF190i DIMENSIONS
OM
ZO IN
2.9&quot; [74.9mm]
4.05&quot; [103mm]
]
m
m
.2
27
1
[
5&quot;
ZOO
OU M
T
ENT
CLR
MENU
GOTO
MARK
ROUTE
FIND
MOB
REMOVABLE
Grip
4.4&quot; [111mm]
20.2
1.4&quot; [36.5mm]
PWR
REMOVABLE
Mounting Bracket
3.9&quot; [98.6mm]
7.1&quot; [181mm]
3.7&quot; [94mm]
0.6&quot;
[14mm]
0.8&quot;
[20mm]
&Oslash;
[&Oslash; 0.2
4m &quot;
m]
1.7&quot;
[44mm]
1.8&quot; [45mm]
2.1&quot; [53mm]
1.5&quot;
1.5&quot;
[37mm] [37mm]
0.2&quot; [4.1mm]
Figure 20.2 - CP190i/CPF190i Dimensions [inch/mm]
20.3
OPTIONAL FF525 FISH FINDER SPECIFICATIONS
(USE WITH CP190i)
Power Output
: 600W or 1kW depending on connected transducer
Frequency
: 50 and 200kHz
Minimum Depth
: 5Feet at 50kHz, 2.5Feet at 200kHz
Maximum Depth
: 1500FT at 50kHz, 700FT at 200kHz
Airmar X-DUCER ID
: Must use Standard Horizon transducers
Advanced Digital Signal Processing
Speed &amp; Temperature Sensor (if available on transducer)
Alarms (shallow water, depth, Fish, temp)
Trip Log, Fish Symbols
STC, Interference Rejection, Automatic noise reduction
A-Scope, White Line, Zoom x2/x4
Auto range/gain/frequency/shift/ping rate
16/256 colors display user selectable
Page 144
CP190i and CPF190i
20.4
OPTIONAL WAAS GPS RECEIVER SPECIFICATIONS
This optional WAAS GPS Receiver is based on a ultimate GPS engine that delivers
accuracy better than three meters by decoding the GPS correction signals from the satellitebased WAAS (Wide Area Augmentation System). The GPS engine, interface electronics
and the passive antenna are enclosed inside the water-proof plastic housing. This provides
advanced state of the art GPS performance in an easy to use package.
Physical Characteristics
Color
Dimensions
Weight (without cable)
Cable
Electrical Characteristics
Input Voltage
Input Current
GPS Receiver Sensitivity
GPS Performance
GNSS Systems
Ivory white
97mm in diameter x 32mm in height (flush mounted) or 61,5mm on flag-pole mount
0,35 lb (160 g)
white 15 meter 8x28AWG cable with 6 pins female connector
10 Vdc to 35 Vdc unregulated
0.8 Wmax
Tracking, Navigation
:-160 dBm
Acquisition, Reacquisition :-160 dBm
Cold Starts
:-145 dBm
GPS
GALILEO
SBAS
: L1 C/A
: L1
: WAAS (North America), EGNOS (Europe), MSAS (Asia),
GAGAN (Indian)
Geodetic Datum
Channels
WGS84
32 + 18
Acquisition Time
Reacquisition
Hot Start
Warm Start
Cold Start
&lt; 1 second
1 second outdoor, 10 seconds indoor
29 seconds
29 seconds
Accuracy
GPS
with SBAS
&lt; 2.5m
&lt; 2.0m
NMEA Output
Messages
GGA, RMC, GSA, GSV, TXT
CP190i and CPF190i
Page 145
Page 146
CP190i and CPF190i
21. APPENDIX: TERMS
ALT (Altitude) – Shows the Altitude of the GPS Antenna on the mean sea level. It i received
from GPS, sentence GGA.
APP Wind DIR SPD (Apparent Wind Direction) – Shows the Apparent Wind Direction when
a external wind instrument with NMEA is connected.
APP Wind SPD (Apparent Wind Speed) – Shows the Apparent Wind Speed when a
external wind instrument with NMEA is connected.
BRG (Bearing) – The direction from your current position to a Destination point.
COG (Course Over Ground) – The course your vessel is heading.
DATE – Shows the current date received by the GPS.
DEPTH – Shows the water depth when the optional Digital Depth Sounder is connected.
DEPTH AREAS – Depth Areas are the sea areas included in the user selectable range of
minimum and maximum depth limits. The sea area that is beyond the selected range is filled
by an uniform white color, the sea area that is inside the selected range is filled by ordinary
multicolor shading. The Spot Soundings and Depth Contours are displayed on the range only.
DRAUGHT – Depth of water the vessel draws.
The definition of draught (or draft) of a ship’s hull is the vertical distance between the
waterline and the bottom of the hull (keel). Draught determines the minimum depth of water
a ship or boat can safely navigate.
On the Celestial page the “draught” window shows the height of the tidal water during a
24hr period of time. This height is dependant on the time of day selected using the
ShuttlePoint knob.
DSC (Digital Selective Calling) – Digital Selective Calling is a semi-automated method of
establishing a VHF Radio call. DSC had also been designated as part of the Global Maritime
Distress and Safety System (GMDSS). It is planned that DSC will eventually replace aural
watches on distress frequencies and will be used to announce routine and urgent maritime
safety information broadcasts.
DST (Distance) – The distance from your current position to a Destination point.
ETA – Estimated Time of Arrival
GPS Constellation – The Global Positioning System (GPS) is a space-based radionavigation system consisting of a constellation of satellites and a network of ground stations
used for monitoring and control. A minimum of 24 GPS satellites orbit the Earth at an altitude
of approximately 11,000 miles providing users with accurate information on position,
velocity and time anywhere in the world and in all weather conditions.
GPS2D – The GPS is receiving at least 3 valid satellites.
GPS3D – The GPS is receiving at least 4 Satellites.
HDG (Heading) – Shows heading from a External Flux Gate Compass when connected.
HDOP/VDOP – Horizontal/Vertical Dilution of Precision. It is a parameter indicating the
precision of the positioning system (GPS). The smaller the HDOP/VDOP value, the more
CP190i and CPF190i
Page 147
accurately the position fix is provided.
HEIGHT – The current tide height referred to the vertical cursor.
HIGH WATER – The maximum level of the tide height in 24 hours.
LOW WATER – The minimum level of the tide height in 24 hours.
PINGO – It is a mound of earth-covered ice found in the Arctic and subarctic that can reach
up to 70 metres (230FT) in Height and up to 600 metres (2.000 FT) in diameter.
Position Request – Marine DSC VHF Function of transmitting a GPS position to another
Marine DSC VHF. When GPS Chart Plotter is connected to STANDARD HORIZON GPS
the position of another vessel is shown on the Chart page.
SPEED – Shows the Speed Thru the Water when a Digital Speed Log is connected.
SOG (Speed Over Ground) – The speed you vessel is travelling at.
STEER – Heading to steer to destination Waypoint.
TIME – Shows the current time received by the GPS.
TRIP LOG – Shows the distance the vessel has travelled since the trip log was reset.
TRU Wind DIR (True Wind Direction) – Shows the True Wind Direction when an external
wind instrument with NMEA is connected.
TRU Wind SPD (True Wind Speed) – Shows the True Wind Speed when an external wind
instrument with NMEA is connected.
TTG (Time To Go) – Shows time to go to reach a Destination point.
UNITS
Nm Nautical Mile (1 NM = 1.15 Sm or 1.85Km)
Sm Statue Mile (1Sm = 0.87Nm or 1.61Km)
Km Kilometer (1 Kilometer = 0062 Sm or 0.54Nm)
FT Feet (1 Foot = 0.167 Fathoms or 0.305 Meters)
FA Fathom (1 Fathom = 6 Feet or 1.83 Meters)
Mt Meter (1 Meter = 3.28 Feet or 0.55 Fathoms)
Kts Knot (1 Knot = 1.15 MPH or 1.85 KPH)
MPH Miles Per Hour (1 MPH = 0.87 Knots or 1.61 KPH)
Kmh Kilometer Per Hour (1 KPH = 0.54 Knots or 0.62 MPH)
VMG – It is the destination closing Velocity. The VMG is calculated using the current speed
of the vessel (SOG) and the difference between the current vessel course and the bearing
to the Destination.
WAAS 2D/3D – The GPS is receiving a 2D or 3D position and the correction from the WAAS
Satellite. WAAS consists of approximately 25 ground reference stations positioned across
the United States that monitor GPS satellite data. Two master stations, located on either
coast, collect data from the reference stations and create a GPS correction message. This
correction accounts for GPS satellite orbit and clock drift plus signal delays caused by the
atmosphere and ionosphere. The corrected differential message is then broadcast through
one of two geostationary satellites, or satellites with a fixed position over the equator. The
information is compatible with the basic GPS signal structure, which means any WAASenabled GPS receiver can read the signal.
Page 148
CP190i and CPF190i
WATER TEMP – Shows the sea water temperature for when a Digital Speed Log/Temp
instrument with NMEA is connected.
XTE (Cross Track Error) – The distance your vessel is off course (left or right) to a
Destination point.
CP190i and CPF190i
Page 149
Page 150
CP190i and CPF190i
ANALYTICAL INDEX
1 Line Small/Large ............................ 89
16/256 colors display ...... 13, 143, 144
2 Line Small ...................................... 89
200 kHz Full .................................... 127
50 kHz Full ...................................... 127
50&amp;200kHz ..................................... 127
A
A-Scope ................................. 125, 135
About ................................................. 39
ABOUT PAGE ................................... 39
About page ............................... 40, 119
Accessories ...................................... 14
ACCURACY ...................................... 79
ACQUIRING ...................................... 98
Activation Range .................... 111, 112
Active Target ................................... 111
ACTIVE TRACK ......................... 82, 83
ADDITIONAL ROUTES .................... 75
Adjusting Time .................................. 34
ADVANCED SETUP ....................... 105
Advanced Setup menu .................... 105
AIS ........................................... 13, 111
AIS List ..................................... 13, 114
AIS List page ................... 13, 113, 114
AIS MENU ....................................... 112
AIS NMEA message .................. 22, 24
AIS Receiver ........ 20, 22, 24, 25, 105
AIS SETUP ..................................... 112
AIS Setup ................................... 22, 24
AIS Symbols ................................... 112
Alarm Status List ............................. 121
Alarms menu .......................... 107, 136
Alaska ................................. 13, 51, 87
ALT .......................................... 89, 147
Alternate Solution ............................ 107
Altitude .............................. 38, 89, 147
Anchor Alarm .................................. 108
APA ............................... 105, 106, 143
APB ........................................ 106, 143
Apparent Wind Direction .......... 89, 147
Apparent Wind Speed .............. 89, 147
Arrival Alarm ................................... 108
ASF ................................................... 36
ASF1/2 ............................................ 107
assistance ......................................... 13
CP190i and CPF190i
Attention Areas ................................. 92
Audible Alarm .................................. 108
Auto Full page ................................. 127
AUTO INFO ............................... 39, 91
Auto Info .......................................... 111
Auto Info settings .............................. 91
Auto Mode ....................................... 130
Auto Position ................................... 109
Auto Range ..................................... 130
AUTOMATIC CHECK ....................... 79
Automatic Route Check .................... 79
AUTOMATIC TIME ........................... 34
Autopilot ........................ 20, 22, 24, 25
AUTOPILOT CONNECTION ..... 21, 23
AWD ................................................. 89
AWS .................................................. 89
B
Backlight .................................. 33, 141
backup .............................................. 85
Bahamas ............................. 13, 51, 87
Bathymetric ....................................... 53
BATTERY CONNECTIONS .............. 25
Baud Rate ....................................... 142
Beacons ............................................ 92
Bearing ..................................... 69, 147
bearing line ....................................... 69
Bearing to Destination ...................... 89
Bearings .......................................... 107
BOD ....................................... 106, 143
Bottom Echo Profile ........................ 126
Bottom Lock .................................... 130
BRACKET MOUNTING .................... 17
BRG .................................. 69, 89, 147
BUILT-IN CHARTS ........................... 51
Built-In Charts ................................... 13
Buoys ......................................... 90, 92
BWC ....................... 99, 105, 106, 143
C
C-CARD ...... 51, 52, 54, 85, 137, 142
C-CARD Connector ........................ 142
C-CARD Test .................................. 142
C-COM ................................... 105, 115
C-Weather .................... 105, 115, 116
C-Weather menu ............................ 115
Page 151
Calibrate Water Speed ................... 135
Calibrate Water Temp ..................... 135
Calibration ....................................... 107
camera icon ..................................... 62
Canada ............................... 13, 51, 87
Caribbean ........................... 13, 51, 87
CARTOGRAPHY .............................. 51
Cartography .................................... 143
Cartridges ....................................... 142
Category ........................................... 47
CAUTION ............................................ 5
Caution page ..................................... 30
CELESTIAL PAGE ............................ 97
Central America .................. 13, 51, 87
Chain ........................................ 36, 107
Change Focus ................................... 88
change the fields ............................... 29
change the scale ............................... 29
Chart ................................................. 83
Chart Boundaries ....................... 92, 94
CHART CONFIGURATIONS ............ 95
Chart Datum .................................... 106
Chart Language ................................ 61
Chart Lock .................................. 92, 94
CHART PAGE ............................ 38, 87
Chart page ........................................ 31
Chart Scale ....................................... 90
chart scale selection ......................... 55
Chart selection menu ........................ 88
Chart Settings ............................ 93, 95
Chinese ............................................. 37
Classic ....................................... 36, 38
Clear Info .......................................... 53
Clear View ......................................... 53
CLR ................................................... 29
COG ................... 81, 87, 89, 112, 147
COLOR ............................................. 78
Color AIS Targets ........................... 114
Color Settings ................................. 134
COLOR TARGET AIS ..................... 114
Color Targets AIS ............................. 13
COMPASS ........................................ 89
Compass menu ............................... 107
COMPASS ROSE ............................. 38
Compass Rose ................... 13, 95, 96
Compass Table ............................... 107
COMPASS TAPE .............................. 96
Compass Tape ........................... 95, 96
confirm selection ............................... 29
Connect the MOBILARM ................ 117
CONNECTIONS ............................... 20
Page 152
Contrast ................................... 33, 141
CONTROLS ...................................... 29
conventions ................................ 17, 29
Coordinate System .................. 35, 106
Coordinates ....................................... 48
Copyright ............................................. 4
Course ............................................ 109
Course Over Ground ........ 81, 89, 147
COURSE UP ..................................... 38
Course Up ......................................... 33
Coverage areas ................................ 51
CP190i Connection Table ................. 21
CP190i Connections ......................... 21
CPA ........................................ 111, 112
CPA Alarm ............................. 111, 112
CPA Limit ............................... 111, 112
CPF190i Connection Table ............... 23
CPF190i Connections ....................... 23
create a Route .................................. 75
Creating a Route ............................... 73
CREATING MARKS .......................... 65
cross hair .......................................... 32
Cross Track Error .................... 89, 149
Cuba ................................... 13, 51, 87
Current Date ..................................... 90
Current Time ..................................... 90
Currents Prediction ........................... 60
CURSOR .......................................... 69
cursor ................................................ 32
Cursor Control ................................ 109
Cursor mode .............................. 29, 32
CURSOR SPEED ............................. 38
Cursor Speed menu .......................... 32
CURSOR WINDOW ......................... 39
Customizing the Data Windows ........ 90
D
dangerous ......................................... 78
Dangerous Target ........................... 111
Danish ............................................... 37
Data Bits ......................................... 142
Data Safety Indicator ................. 58, 94
Data window layout ........................... 89
Data Windows ................................... 89
DATE ....................................... 90, 147
Date ................................................ 109
DATE FORMAT ................................ 38
Datum ............................................. 106
DBT ................................. 99, 106, 143
DC Power Connection ............... 21, 23
Deep Alarm Bar .............................. 125
CP190i and CPF190i
DEEP WATER ................................ 124
Deep Water ..................................... 136
DELETE ..................................... 82, 86
delete a Route ................................... 77
Delete PTX ...................................... 120
Deleting a file .................................... 86
Deleting a Mark ................................. 66
DELETING A MOB ........................... 71
DELETING A ROUTE ....................... 77
Deleting a Track ................................ 82
Deleting a Waypoint .......................... 66
deleting User Points .......................... 67
DEMO MODE ................................... 27
Demo Mode .................................... 109
Demonstration Mode ........................ 27
DEPTH ............................................ 147
Depth ................................ 38, 89, 131
Depth Alarm .................................... 108
DEPTH AREAS ............................... 147
Depth contours .................................. 51
DEPTH LIMIT .................................... 79
Depth Range Max ...................... 92, 93
Depth Range Min ....................... 92, 93
Depth Settings ........................... 93, 95
Depth Sounder .................................. 25
DEPTH TREND .............................. 101
Depths ............................................... 53
destination point ................................ 69
Detailed Port Plan ............................. 53
Detailed World Background .............. 53
Diagrams .................................... 53, 61
DIFF CORRECTION SOURCE ........ 98
Differential Correction Source ........... 99
Diffusers .............................. 78, 92, 95
Digital Depth ................................... 124
Digital Instruments ............................ 20
Digital Selective Calling .................. 102
DIM Menu ....................................... 141
Dimensions ..................................... 144
disable Demo mode .......................... 28
Display ............................................ 143
display ............................................... 13
DISPLAY COLOR ............................. 38
Display Color ....................... 17, 36, 99
Display Mode .................................... 91
Display Mode settings ....................... 91
display of AIS Targets ..................... 112
Display Setup menu ........................ 134
DISTANCE ........................................ 83
Distance ..................................... 38, 69
Distance to Destination ..................... 89
CP190i and CPF190i
Distance Units and Time Units ......... 81
Distress Call .................................... 102
Download Area ............................... 115
download weather data ................... 115
DPT ................................. 99, 106, 143
DRAUGHT ...................................... 147
draught .............................................. 97
Dredged Areas .................................. 78
DSC ............... 99, 102, 109, 143, 147
DSC Distress Call ........................... 102
DSC POLLING ................................ 109
DSC VHF Radio ................................ 25
DSE .......................................... 99, 143
DSI ............................................. 58, 94
DST ................................... 69, 89, 147
DTP ................................................... 89
Dual Chart page ................................ 88
Dutch ................................................. 37
Dynamic Currents ............................. 53
Dynamic Nav-Aids ..................... 53, 58
E
EDIT .................................................. 67
Edit .................................................... 65
EDIT ROUTE ............................. 74, 76
Edit Route .................................. 74, 78
EDITING A MARK ............................. 65
EGNOS ............................................. 98
Electronic chart ................................... 4
ENABLE/DISABLE .......................... 123
Enhanced Mixing Levels ................... 53
Enhanced Port Info .................... 53, 63
ENT ................................................... 29
Estimated Time of Arrival .................. 90
ETA .......................................... 90, 147
external GPS antenna ....................... 17
Extra Large Coverage ....................... 53
F
FA ................................................... 148
FCC ..................................................... 4
features ............................................. 13
FF MODULE ................................... 144
FF520 ....................................... 26, 101
FF525 ... 13, 20, 22, 25, 26, 101, 105
FIND .................................... 13, 30, 67
Find ................................................... 53
find a point ........................................ 67
Find GPS Coordinates ...................... 49
Find Information ................................ 49
Find Lakes By Name ......................... 47
Page 153
Find Lakes Information ..................... 45
Find Obstructions .............................. 45
Find Points Of Interest ...................... 48
Find Port ........................................... 42
Find Port Services ............................ 42
FIND SERVICES .............................. 41
Find Tide Stations ............................. 43
Find User Points ............................... 48
Find Wrecks ...................................... 44
Finnish .............................................. 37
Fish ........................................ 125, 136
FISH FINDER ............. 13, 20, 25, 123
Fish Finder display .......................... 125
Fish Finder page ............................. 124
Fish Finder page selection .............. 126
Fish Finder Setup menu ................. 128
Fish Finder window ......................... 124
FISH SPOT ..................................... 124
Fish Symbols .................................. 135
Fish/Chart page .............................. 128
Fishing Facility .................................. 78
fix .................................................... 139
Fix coordinates .................................. 35
Flexi-Zoom ................................. 53, 55
FLUSH MOUNTING .......................... 18
Flush mounting antenna ................... 19
Focus ................................................ 88
focus ............................................... 128
Forecast .......................................... 116
form a Route ..................................... 30
FORMAT ........................................... 85
Formatting ......................................... 85
French ............................................... 37
FREQUENCY ................................. 129
FT .................................................... 148
Full Display pages ........................... 127
Full Info On Lakes ............................. 46
Full Info page .................................... 46
G
Gain ................................................ 132
GAIN MODE ................................... 130
General ............................................. 89
German ............................................. 37
GGA ................................ 99, 106, 143
GLL ......................... 99, 105, 106, 143
GOTO ........................................ 30, 87
GOTO A ROUTE .............................. 77
GOTO CURSOR ............................... 69
GOTO MARK .................................... 70
GOTO menu ..................................... 69
Page 154
Goto PTX ........................................ 120
GOTO ROUTE .................................. 70
GPS .................................................. 99
GPS antenna ............................. 17, 19
GPS Constellation ........................... 147
GPS Coordinates .............................. 30
GPS Receiver .......................... 17, 145
GPS SETUP menu ........................... 98
GPS Setup Menu .............................. 99
GPS Status ....................................... 90
GPS STATUS PAGE ........................ 98
GPS Status page .............................. 31
GPS2D ..................................... 98, 147
GPS3D ..................................... 98, 147
Great Lakes ........................ 13, 51, 87
Greek ................................................ 37
Grounding Alarm ............................. 108
Grounding Alarm Range ................. 108
Grounding Alarm Report ................. 108
GSA ......................................... 99, 143
GSV ......................................... 99, 143
Guardian Alarm ................................. 53
H
Hawaii ................................. 13, 51, 87
HDG ................. 89, 99, 106, 143, 147
HDM ......................................... 99, 143
HDOP ................................ 90, 98, 147
HDT .......................................... 99, 143
Heading ............................................. 89
HEIGHT .......................................... 148
HIGH WATER ................................. 148
High Water ........................................ 98
HIGH WATER TEMP ...................... 124
HIGHWAY ......................................... 89
Highway ............................................ 83
HIGHWAY PAGE .............................. 96
highway scale ................................... 96
Home mode ............................... 29, 32
Horizontal Dilution of Precision ......... 90
HSC ....................................... 106, 143
HTG ................................................ 143
I
ICON ................................................. 67
Icon Size ........................................... 56
Info Tree ............................................ 49
Information ................................. 30, 49
Input ................................................ 105
Input Data Display ........................... 142
INPUT/OUTPUT ............................. 105
CP190i and CPF190i
INSERTING A WAYPOINT ............... 76
Inserting C-CARD ...................... 51, 52
INSTALLATION ................................ 17
Interface .......................................... 143
Interference Rejection menu ........... 131
Internal GPS ..................................... 99
internal GPS antenna ........................ 17
INTERNET ...................................... 115
Intertidal Areas .................................. 78
IP56 ................................................... 13
ISO Certification ................................ 53
Italian ................................................ 37
J
Japanese .......................................... 37
K
Keel Offset ...................................... 135
key .................................................... 29
Keyboard ......................................... 143
KEYPAD BEEP ................................. 38
Km ................................................... 148
Kmh ................................................. 148
Kts ................................................... 148
L
Lake .................................................. 45
Lake CARD ....................................... 45
Lakes By Name .......................... 30, 47
Lakes Information ...................... 30, 45
Land Areas ........................................ 78
Land Elevation .................................. 53
Land Elevation Values ............... 92, 93
Land Elevations ......................... 92, 93
Land Settings ............................. 93, 95
LANGUAGE ...................................... 39
Language ................................... 36, 61
Language Selection .......................... 37
Lat/Lon Grid ............................... 92, 94
Latitude ...................................... 35, 48
LCD backlight .................................... 33
LCD contrast ..................................... 33
legend ........................................ 17, 29
Lights ......................................... 90, 92
LINE COLOR .................................... 82
LOAD ................................................ 86
Load settings ................................... 137
Loading a file ..................................... 86
LOCATE ............................................ 67
locate Points Of Interest ................... 47
locate Port ......................................... 42
CP190i and CPF190i
locate Port Services .......................... 41
locate Tide Stations .......................... 42
locate Wrecks ................................... 43
Longitude ................................... 35, 48
Loop-Back Test ............................... 142
Loran ................................................. 35
Loran TD ......................................... 107
LOW WATER ................................. 148
Low Water ......................................... 98
LOW WATER TEMP ...................... 124
M
Main Menu ........................ 29, 87, 126
MAN OVER BOARD ......................... 71
Manual Mode .................................. 130
Marine Settings .......................... 92, 95
MARK .................................. 13, 30, 65
Mark ............. 13, 30, 48, 65, 66, 67,
73, 75, 85, 143
Mark editing ...................................... 66
Mark Icons ........................................ 66
MARKS/WAYPOINTS LIST .............. 67
Marks/Waypoints List ....................... 68
MARKS/WPTS .................................. 67
MAX .................................... 51, 54, 55
Max Functions ................................... 55
Max Speed ........................................ 89
MEASURE DISTANCE ..................... 38
Memory ........................................... 143
memory ............................................. 85
MENU ............................................... 29
Mixing Levels ...................... 53, 92, 94
MMSI ............................................... 111
MMSI number ........................ 111, 112
MOB ........................................... 30, 71
MOBILARM ............................ 105, 117
MOBilarm PTX List page ................ 121
MOBILARM System .......................... 25
Mooring ............................................. 78
mounting bracket .............................. 13
mounting the antenna ....................... 19
Moving a Mark .................................. 66
Moving a Waypoint ........................... 66
MPH ................................................ 148
Mt .................................................... 148
MTW ............................... 99, 106, 143
Multilanguage Support ...................... 53
N
Name Tags ....................................... 92
NAME TO A ROUTE ......................... 74
Page 155
O
Object Info ......................................... 53
Obstruction icons Table .................... 44
Obstructions ........... 30, 44, 78, 92, 95
Off-line redraw .................................. 53
Official data source ........................... 53
OLYMPIC ROUTE ............................ 74
Olympic Route .................................. 13
Olympic Route creation .................... 75
OM CODE ........................................... 4
On All ................................................ 91
On Points .......................................... 91
Open Array ........................................ 14
Ouput .............................................. 105
Over-Zoom ........................................ 56
Pair ........................................... 36, 107
Palette ............................................... 59
Parity ............................................... 142
PC COM settings .............................. 26
PC-Planner ..................................... 115
PERSONAL COMPUTER ................. 26
Personal Computer ........................... 25
Perspective View ....................... 53, 57
Photos ............................................... 53
Pictures ............................................. 61
Pin ................................................... 115
PINGO ............................................ 148
Pingos ............................................... 78
Place Name Size .............................. 56
Place Names ..................................... 92
Places a Mark ................................... 30
places a Waypoint ............................ 30
PLACING A MOB .............................. 71
Points Of Interest .......... 30, 47, 92, 93
Port .......................................... 42, 142
Port Areas ......................................... 65
Port Icons .......................................... 90
Port Info ..................................... 53, 65
Port Marinas ..................................... 65
Port Services ...................... 30, 41, 65
Port Services Table .......................... 41
Ports .................................................. 30
Ports &amp; Services ............................... 92
Portuguese ........................................ 37
POSITION Request ........................ 102
Position Request .................... 103, 148
Position Request Call ..................... 102
POSITION Send ............................. 102
Position Send Call ........................... 102
Power Consumption ........................ 143
Power Data Cable ...................... 21, 23
Power On, Off ................................... 30
Power supply ........................... 20, 143
Presets table ................................... 129
Production Installation ...................... 78
PTX ........................................ 118, 119
PTX icon ......................................... 119
PTX information window ................. 120
PTX warning window ...................... 120
Puerto Rico ......................... 13, 51, 87
PWR ................................................. 30
P
package ............................................ 14
Packing List ....................................... 14
PAGES .............................................. 87
Q
Quick Info .......................................... 53
QUICK INFO ON AIS ...................... 112
Quick Info on AIS ............................ 113
Nav Aids &amp; Light Sectors .................. 92
NAV AIDS PRESENTATION ............ 38
nav-aids ............................................ 51
Navigate Menu ................................ 106
Navigation ......................................... 83
NAVIGATION PAGE ........... 38, 95, 96
Navigation Speed .............................. 99
NEW MARK ............................... 67, 68
Night ........................................... 36, 38
night vision ........................................ 36
Nm .................................................. 148
NMEA ..................... 67, 68, 78, 83, 99
NMEA CONNECTIONS .................... 25
NMEA DATA PAGE ........................ 100
NMEA Data page ..................... 27, 101
NMEA Devices .................................. 20
NMEA Display menu ....................... 100
NMEA DISPLAY PAGE .................... 99
NMEA Input ..................................... 143
NMEA Output ........................... 21, 143
NMEA sentences .............. 27, 99, 105
NMEA TREND PAGES ................... 101
NMEA-0183 .................................... 105
NO DATA ........................................ 124
NOAA .................................. 36, 38, 53
Normal ....................................... 36, 38
NORTH UP ....................................... 38
North Up ............................................ 33
Norwegian ......................................... 37
NT/NT+ ............................................. 54
Page 156
CP190i and CPF190i
Quick Info On Lakes ......................... 45
quick zoom ........................................ 29
R
Radar .......................... 13, 14, 25, 105
RADAR ANTENNA ........................... 26
Radio Call Sign ...................... 111, 112
Radome ............................................ 14
RAM ................................................ 139
RAM Clear ...................................... 141
RAM Menu ...................................... 141
Range Bar ....................................... 125
RANGE MENU ................................ 130
Range Mode ................................... 130
Real Time View ............................... 116
RECEIVE ................................... 68, 78
record a Track point .......................... 81
REFRESH ......................................... 86
Refreshing ......................................... 86
replacement parts ............................. 14
REPORT ........................................... 74
Resolution ....................................... 143
Restart GPS ...................................... 99
Restore settings .............................. 137
REVERSE ......................................... 78
RMA ....................................... 106, 143
RMB ....................................... 106, 143
RMC ................................ 99, 106, 143
Roads .................................. 53, 92, 93
Rocks .................................. 78, 92, 95
ROUTE ............................... 13, 30, 65
Route
13, 30, 65, 73, 77, 85, 109, 143
Route Check .............................. 13, 78
Route Check parameters .................. 79
ROUTE CHECK REPORT ................ 79
Route leg ........................................... 78
ROUTE MENU .................................. 78
Route Report ..................................... 74
ROUTE WIDTH ................................ 79
RTE ...................... 27, 67, 78, 99, 143
Russian ............................................. 37
S
safe navigation ........................... 78, 97
Safety Route Check .......................... 54
Safety Status Bar ....................... 53, 58
Satellite ...................................... 13, 98
Satellite Imagery ............................... 59
satellite reception .............................. 98
SAVE ................................................ 86
CP190i and CPF190i
Save settings .................................. 137
SCALE .............................................. 90
screen ........................................ 5, 139
screen display pages ........................ 87
Scrolling Speed ............................... 134
Seabed Type ..................................... 92
Search ............................................... 53
SELECT ............................................ 78
Select Country To Call .................... 115
SELECT ROUTE .............................. 77
select the language ........................... 37
SEND ......................................... 67, 78
Sensitivity menu .............................. 132
sentences .......................................... 27
Serial Ports ..................................... 142
Setup / Reset .................................... 83
Setup Menu ....................................... 99
Shallow Alarm Bar .......................... 125
SHALLOW WATER ........................ 124
Shallow Water .......................... 78, 136
Shift ................................................. 131
Ship icons .................................. 13, 33
Shoreline Constructions .................... 78
ShuttlePoint knob .............................. 29
SI-TEX .............................. 14, 26, 105
Signals .............................................. 92
SIM Pin ........................................... 115
Simulation Menu ............................... 27
Simulation menu ............................. 108
Simulation Mode ............................. 108
Single Chart page ............................. 88
Sleeping Target ............................... 112
slot .................................................... 52
Sm ................................................... 148
Smart GPS Cable ............................. 20
Software ............................................ 39
SOG ................... 13, 87, 89, 112, 148
SOG TREND ................................... 101
SORT ................................................ 67
Spanish ............................................. 37
SPD ................................................... 89
SPECIFICATIONS ................. 143, 144
SPEED ............................................ 148
Speed .......................... 38, 81, 89, 109
Speed Filter ................................ 13, 99
Speed Log ......................................... 25
Speed Over Ground ................. 89, 148
Spot Soundings ................................. 53
spot soundings .................................. 51
start a new Track .............................. 82
start navigating ........................... 30, 69
Page 157
Start-Up page .................................... 30
starting Waypoint .............................. 73
Static Navigation ............................. 107
STC ................................................. 132
STC Length ..................................... 133
STC Preset values table ................. 133
STC Strength .................................. 133
STEER ............................................ 148
Steering ............................................. 89
STEP UNIT ................................ 81, 82
Stop Goto PTX ................................ 121
stop navigation .................................. 30
STR ................................................... 89
Structures ....................................... 126
SunLight ..................................... 36, 38
Surface Clutter ....................... 126, 132
Surface Noise Filter ........................ 133
Surface Noise Filter Depth table ..... 134
Swedish ............................................ 37
System Test .................................... 141
T
Target .............................................. 111
TCPA ..................................... 111, 112
TCPA Alarm ........................... 111, 112
TCPA Limit ............................. 111, 112
TD ................................... 35, 106, 107
technical support ............................... 13
Temp ................................................. 90
TEMP TREND ................................. 101
Temperature .............................. 14, 38
temperature ..................................... 143
Temperature Lower ......................... 136
Temperature Rate ........................... 136
Temperature Upper ......................... 136
TERMS ........................................... 147
Thermoclines .................................. 125
THICKNESS ..................................... 78
Tidal .................................................. 51
Tidal stream ...................................... 60
Tide ............................................ 42, 60
Tide draught ...................................... 43
Tide Graph ................................. 43, 97
Tide height ................................. 43, 97
Tide information ................................ 97
Tide Stations ....................... 30, 42, 90
Tides &amp; Currents ............................... 92
Tides Preview ................................... 53
TIME ................................. 83, 90, 148
Time ......................................... 81, 109
Time Format ...................................... 38
Page 158
TIME SETUP .................................... 38
Time To Go ....................................... 89
TLL ........................................... 99, 143
TLOG ......................................... 83, 90
Towers .............................................. 90
Track ................................... 81, 85, 87
Track Points ............................. 81, 143
Track points ...................................... 13
TRACKING ......................... 81, 82, 90
Tracks &amp; Routes ........................ 92, 93
transducer ................................ 14, 101
Transducer Setup menu ................. 135
Transferring files ............................... 85
Transmit Frequency ........................ 125
TRIP LOG ................................ 83, 148
Trip Log ...................................... 83, 90
Trip Log Reset .................................. 83
TROUBLESHOOTING .................... 139
True Wind Direction ................. 89, 148
True Wind Speed ..................... 89, 148
True-Type Font ................................. 53
TTG .......................................... 89, 148
turn the GPS Chart Plotter On ... 30, 52
TWD .................................................. 89
TWS .................................................. 89
Type .................................................. 47
Type of Data ................................... 116
U
Under-Zoom ...................................... 56
Underwater Ob. Limit ........................ 92
Underwater Object Limit ................... 95
Underwater Objects Settings ............ 95
Underwater Settings ......................... 95
UNITS ............................................. 148
UNITS OF MEASURE ...................... 38
Updating Built-In Charts .................... 51
US English ........................................ 37
User C-CARD .. 65, 85, 115, 116, 137
User C-CARD Menu ......................... 85
User Points ....................... 30, 48, 143
Using the Trip Log ............................. 83
UTC ................................................... 34
UTM ......................................... 35, 106
V
VAD ................................................... 94
Value Added Data ...................... 92, 94
Variable Depth Marker .................... 125
Variation .......................................... 107
VDM ................................................ 125
CP190i and CPF190i
VDOP ................................ 90, 98, 147
Velocity Made Good .......................... 90
Vertical Dilution of Precision ............. 90
Vessel Name ................................... 112
vessel position .................................. 87
VHF ............................................ 22, 24
VHF RADIO ...................................... 25
VHF radio ........................................ 102
VHF’s ................................................ 20
VHW ............................... 99, 106, 143
VISIBLE ............................................ 82
VMG ......................................... 90, 148
VTG ......................... 99, 105, 106, 143
VWR ........................................ 99, 143
VWT ......................................... 99, 143
W
WAAS ............................... 90, 98, 145
WAAS 2D/3D ........................... 98, 148
WAAS GPS ....................................... 13
WAAS GPS antenna ......................... 20
WAAS/EGNOS ................................. 98
Warning Message ........................... 124
Warping Facility ................................ 78
Warranty ........................................... 13
Water Resistance ........................... 143
water resistent .................................. 13
WATER TEMP ................................ 149
WATER TEMP RATE ..................... 124
CP190i and CPF190i
Water Temperature ........... 81, 90, 124
Waypoint ...... 30, 48, 65, 66, 67, 73,
76, 143
WCV ............................. 105, 106, 143
Weather data package .................... 115
Weather Forecast ........................... 116
Weight ............................................. 143
WGS84 ........................................... 106
White Line .............................. 126, 134
Wind Instrument ................................ 25
WIND SPEED TREND .................... 101
WINDOW SETUP ............................. 96
WINDOWS SETUP ................... 38, 89
WPL ..................... 27, 67, 68, 99, 143
Wreck icons Table ............................ 43
Wrecks ..... 30, 43, 51, 78, 90, 92, 95
X
XTE ....... 89, 105, 106, 108, 143, 149
XTE Alarm ..................... 105, 106, 108
Z
zoom ................................................. 29
zoom factor ....................................... 56
Zoom Full page ............................... 127
ZOOM IN ........................................... 29
ZOOM OUT ....................................... 29
Zoom Type ........................................ 55
Page 159
PLEASE NOTE
The following &quot;Limited Warranty&quot; is for customers that have purchased products in
the United States. For Limited Warranty details outside the United States, contact the
dealer in your country.
STANDARD HORIZON LIMITED WARRANTY
STANDARD HORIZON (a division of Vertex Standard USA) warrants, to the original purchaser
only, each new Marine Product (&quot;Product&quot;) manufactured and/or supplied by STANDARD HORIZON against defects in materials and workmanship under normal use and service for a period of
3 years from the date of purchase.
In the event of a defect, malfunction or failure of the Product during the warranty period, Standard
Horizon's liability for any breach of contract or any breach of express or implied warranties in
connection with the sale of Products shall be limited solely to repair or replacement, at its option,
of the Product or part(s) therein which, upon examination by STANDARD HORIZON, appear to be
defective or not up to factory specifications. STANDARD HORIZON may, at its option, repair or
replace parts or subassemblies with or reconditioned parts and subassemblies.
To receive warranty service, the purchaser must deliver the Product, transportation and Insurance
prepaid, to STANDARD HORIZON (Marine Division of Vertex Standard) - Attention Factory Service
- 10900 Walker Street - Cypress, CA 90630, include proof of purchase indicating model, serial
number and date of purchase.
STANDARD HORIZON will not warrant installation, maintenance or service of the Products. In all
instances, STANDARD HORIZON's liability for damages shall not exceed the purchase price of the
defective Product. This warranty only extends to Products sold within the 50 States of the United
Stated of America and the District of Columbia.
STANDARD HORIZON will pay all labor and replacement parts charges incurred in providing the
warranty repair service except where purchaser abuse or other qualifying exceptions exist. The
purchaser must pay any transportation expenses incurred in returning the Product to STANDARD
HORIZON for service.
This limited warranty does not extend to any Product which has been subjected to misuse, neglect,
accident, incorrect wiring by anyone other than STANDARD HORIZON, improper installation, or
subjected to use in violation of instructions furnished by STANDARD HORIZON, nor does this
warranty extend to Products on which the serial number has been removed, defaced, or changed.
STANDARD HORIZON cannot be responsible in any way for ancillary equipment not furnished by
STANDARD HORIZON which is attached to or used in connection with Products, or for the
operation of the Product with any ancillary equipment, and all such equipment is expressly excluded
from this warranty. STANDARD HORIZON disclaims liability for range, coverage, or operation of
the Product and ancillary equipment as a whole under this warranty.
STANDARD HORIZON reserves the right to make changes or improvements in Products, during
subsequent production, without incurring the obligation to install such changes or improvements
on previously manufactured Products. The implied warranties which the law imposes on the sale
of this Product are expressly LIMITED, in duration, to the time period specified above. STANDARD
HORIZON shall not be liable under any circumstances for consequential damages resulting from
the use and operation of this Product, or from the breach of this LIMITED WARRANTY, any implied
warranties, or any contract with STANDARD HORIZON. IN CONNECTION WITH THE SALE OF
ITS PRODUCTS, STANDARD HORIZON MAKES NO WARRANTIES, EXPRESS OR IMPLIED
AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, EXCEPT AS EXPRESSLY SET FORTH HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitation on how an implied warranty lasts, so the above limitation or exclusions may not apply. This
warranty gives specific legal right, and there may be other right which may vary from state to state.
Page 160
CP190i and CPF190i
">

Hello! I am an AI chatbot specifically trained to assist you with the Standard Horizon CP190i CPF190i Owner's manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!