PetSafe

®

In-Ground Radio Fence

™

Plus Trainer

Operating and Training Guide

Please read this entire guide before beginning

+

PROGRAM

2

Thank you for choosing PetSafe ® , the #1 selling brand of electronic training solutions in the world. Our mission is to ensure your pet’s safety by providing you the tools and techniques to successfully train your pet. If you have any questions, please contact the Customer Care Center at 1-800-732-2677 or visit our website at www.petsafe.net.

____________________________________________________________________________________________________________

Table of Contents

Components ................................................................................................................................... 3

Other Items You May Need .............................................................................................................. 3

How the Fence System Works .......................................................................................................... 4

Fence Key Defi nitions ..................................................................................................................... 4

How the Remote Training System Works .......................................................................................... 5

Remote Trainer Key Deffi nitions ...................................................................................................... 5

Fence Operating Guide

Locate the Fence Transmitter ....................................................................................................... 6

Lay Out the System ..................................................................................................................... 6

Position the Boundary Wire ......................................................................................................... 8

Connect the Wires to the Fence Transmitter ................................................................................. 9

Prepare the Receiver Collar ......................................................................................................... 9

Set the Boundary Width and Test the Receiver Collar ...................................................................10

Install the Boundary Wire ...........................................................................................................11

Place the Boundary Flags ...........................................................................................................12

Fit the Receiver Collar ................................................................................................................12

Remote Operating Guide

Prepare the Remote Transmitter ..................................................................................................14

Understanding the Remote Transmitter .......................................................................................14

Fence Training Guide

Be Patient With Your Pet .............................................................................................................15

Days 1 and 2 - Boundary Flag Awareness ....................................................................................15

Days 3 and 4 - Continue Boundary Flag Awareness .....................................................................16

Days 5 thru 8 - Distraction Phase ...............................................................................................16

Days 9 thru 14 - Unleashed Supervision ......................................................................................17

Days 15 thru 30 - Pet Monitoring ...............................................................................................17

Taking Your Pet Out of the Pet Area ............................................................................................17

Remote Training Guide

Eliminating Unwanted Behavior .................................................................................................18

Accessories ....................................................................................................................................20

Frequently Asked Questions ...........................................................................................................20

Troubleshooting .............................................................................................................................21

Short Loop Test .............................................................................................................................22

To Locate a Break in the Wire .........................................................................................................22

Remote Trainer Testing ...................................................................................................................23

Terms of Use and Limitation of Liability .........................................................................................24

FCC ..............................................................................................................................................24

Caution .........................................................................................................................................24

Layout Grid ...................................................................................................................................28

Mounting Template ........................................................................................................................28

1-800-732-2677

Components

Power

Adapter

+

PRO

GRA

M

Fence

Transmitter

Boundary Wire - 500 ft.

Receiver

Collar w/Short

Contact Points

Battery

(PetSafe ®

Wire Nuts

RFA-67)

A F E P E T

A

P P

Y OWN

E

In-Ground

R A D I O F E N C E

™

Video CD compatible with most DVD players and computer

CD-ROM drives

VHS Tape available through our Customer

Care Center at

1-800-732-2677

Streaming Video available at

402-871 www.petsafe.net

Installation and Training

Video CD

RFA-141

Installation and Training

Video CD

Boundary Flags - 50

Test Light

Tool

W ar ranty

9-Volt Battery

Warranty

Card

Remote

Transmitter

Long

Contact Points

Operating and

Training Guide

Other Items You May Need

• Additional wire and fl ags (Part #PRFA-500)

• Tape measure

• Small Phillips screwdriver

• Drill & mounting hardware

• Shovel or lawn edger

• Pliers

• Wire stripping pliers

• Scissors

• Lighter

• Electrical tape

• Additional wire nuts

• Waterproofi ng compound (e.g. silicone caulk)

• PVC pipe or water hose

• Circular saw with masonry blade

• Patching compound

• Staple gun

• Non-metallic collar and leash

Note: For information on professional installation of your new PetSafe In-Ground Radio Fence TM , contact the Customer Care Center at 1-800-732-2677 or visit our website at www.petsafeprofessional.com.

www.petsafe.net 3

How the Fence System Works

The PetSafe In-Ground Radio Fence TM has been proven safe, comfortable, and effective for all pets over 8 pounds. The system works by producing a radio signal from the Fence Transmitter through up to 835 feet of Boundary Wire. The

Boundary Wire is buried or attached to a fi xed object to enclose the Pet Area. You temporarily defi ne this Pet Area with

Boundary Flags for a visual aid in training your pet. Your pet wears a Receiver Collar with Contact Points that touch his neck, and, once trained, is allowed to roam freely in the Pet Area. When your pet reaches the Warning Zone, the Receiver

Collar gives a warning beep. If your pet continues into the Static Correction Zone, a safe Static Correction will be delivered through the Contact Points to get his attention until he returns to the Pet Area.

Fence Key Definitions

Fence Transmitter: The device that transmits the radio signal through the Boundary Wire.

Pet Area: The area within the Warning Zone where your pet can roam freely.

Warning Zone: The outer edge of the Pet Area where your pet’s Receiver Collar begins to beep, warning him not to go into the Static Correction Zone.

Static Correction Zone: The zone beyond the Warning Zone where your pet’s Receiver Collar will emit a Static

Correction, signaling him to return to the Pet Area.

Boundary Width: The combination of the Warning Zone and the Static Correction Zone.

Receiver Collar: The device that receives the radio signal from the Boundary Wire.

Contact Points: The contacts through which the Receiver Collar delivers the safe Static Correction when your pet moves into the Static Correction Zone.

Power Jack: The jack where the Power Adapter plugs into the Fence Transmitter. The Fence Transmitter is powered by a standard 120-volt outlet.

Boundary Control Switch: The switch to adjust according to the length of Boundary Wire used.

Boundary Wire Terminals: The terminals where the Boundary Wires connect to the Fence Transmitter in order to complete a continuous loop.

Loop Indicator Light: The light that indicates that the Boundary Wire makes a complete loop, enabling the signal to be transmitted.

Boundary Width Control: The knob that adjusts the width of the Warning and Static Correction Zones. Note: Adjusting the knob does not change the level of Static Correction on the Receiver Collar.

Fence Transmitter

Fence

Transmitter

Pet Area

Static Correction

Zone

Warning

Zone

Receiver Collar

Battery

BATTER

Y 6V

RFA-67

4

Static Correction

Zone

Warning

Zone

Boundary

Width Washers

Contact Points

1-800-732-2677

Power

Jack

Boundary

Control

Switch

} Boundary Wire

Terminals

Loop Indicator Light

Power Light

Boundary Width

Control

How the Remote Training System Works

The PetSafe Remote Trainer has been proven safe, comfortable, and effective for all pets over 8 pounds. This system assists you in controlling your pet without a leash inside the Pet Area. At the push of a button, the Remote Transmitter sends a signal, activating your Fence System. Using the Remote Trainer consistently and correctly, many misbehaviors that your pet exhibits can be corrected or any basic obedience commands can be taught.

Important: The Remote Trainer only operates within the established Boundary.

Remote Key Definitions

Remote Transmitter: Transmits the Radio Signal to the Receiver Collar.

Transmitter Indicator Light: Indicates when any button on the Remote

Transmitter is pressed. This light also serves as a low battery indicator.

Tone Only Button: Sends an audible tone to your pet. There is no stimulation associated with this button.

Programming Button: Delivers stimulation to your pet through the Contact

Points. When this button is held down continuously for 8 seconds, the Remote

Transmitter will “time-out”, and you must release and press the button again before any additional stimulation can be delivered to your pet.

Remote Transmitter

+

PROG

RAM

Transmitter

Indicator Light

Stimulation and

Tone Button

Tone Only Button

Programming

Button

www.petsafe.net 5

6

Fence Operating Guide

Step

1

Locate the Fence Transmitter

Place the Fence Transmitter:

• In a dry, well ventilated, protected area (1A, 1B).

• In an area where temperatures do not fall below freezing (e.g., garage, basement, shed, closet).

• Secured to a stationary surface using appropriate mounting hardware (not included). A mounting template is included in the back of this guide.

• At least 3 feet from large metal objects or appliances as these items may interfere with the signal consistency (1C).

Once you have mounted the Fence Transmitter, the Boundary Wire must exit the building. This can be accomplished via a window or through a 1/8” hole drilled through the wall. Ensure the drill path is clear of any utilities. Make sure the Boundary Wire is not cut off or pinched by a window, door, or garage door, as this can damage it over time.

To prevent fi res and electrical hazards, install the Fence Transmitter in buildings that are in accordance with state and local electrical codes.

1A 1B 1C

3ft.

____________________________________________________________________________________________________

Step

2

Lay Out the System

Basic Planning Tips

• The Boundary Wire MUST start at the Fence Transmitter and make a continuous loop back (2A).

• Design a layout that is suitable for your yard. Sample layouts are provided in this section, and a grid for designing your layout is provided in the back of this guide.

2A 2B

• Always use gradual turns at the corners to produce a more consistent boundary (2B). Do not use sharp turns, as this will cause gaps in your boundary.

• Avoid making passageways too narrow for your pet to move about freely (e.g., along the sides of a house).

• The Receiver Collar can be activated inside the house if the Boundary Wire runs along the outside wall of the house. If this occurs, remove your pet’s Receiver Collar before bringing him inside, decrease the range using the Boundary Width Control knob or consider an alternative layout.

1-800-732-2677

Sample Layouts

Sample 1:

Perimeter Loop

(Single Loop)

The Perimeter

Loop is the most common layout. This will allow your pet to freely and safely roam your entire property (2C). It can also protect gardens, pools and landscaping (2D).

B

C

D

A

E

Sample 2 (2E): Perimeter Loop Using Existing

Fence (Single Loop)

This layout allows you to include your existing fence as part of your layout and keep your pet from jumping out or digging under your existing fence. It reduces the amount of wire which will need to be buried. From the

Fence Transmitter, run the wire to A, A to B, B to C, C to D, D to E, E to A, twist the wires from A back to the

Fence Transmitter. See the “Install the Boundary Wire” section for more information on attaching the wire to a fence.

www.petsafe.net 7

Step

3

Position the Boundary Wire

Lay out the Boundary Wire using your proposed boundary and test the system BEFORE burying the wire or attaching it to an existing fence. This will make any layout changes easier.

Running the Boundary Wire parallel to and within fi ve feet of electrical wires, neighboring containment systems, telephone wires, television or antenna cables, or satellite dishes will cause an inconsistent signal. If you must cross any of these, do so at 90-degree angles (perpendicularly).

If separating the wire by at least fi ve feet from a neighboring containment system’s wire does not reduce the inconsistent signal, contact the Customer Care Center at 1-800-732-2677.

To Twist the Boundary Wire (3A)

Twisting the Boundary Wire cancels the signal and allows your pet to cross over that area safely. Plastic or metal piping will not cancel the signal.Twist the Boundary Wire 8 to 10 times per foot to cancel the signal.

To Splice or Repair the Boundary Wire (3B)

If you need additional Boundary Wire to expand your wire loop, you will need to splice the wires together. Note the locations of all splices for future reference. Most Boundary Wire breaks occur at splices.

Strip approximately one-half inch of insulation off the ends of the Boundary Wires to be spliced. Make sure the copper Boundary Wire is not corroded. If the Boundary Wire is corroded, cut it back to expose clean copper wire.

Insert the stripped ends into the wire nut and twist the wire nut around the wires. Pull on the wires to make sure you have a strong splice connection. Apply waterproofi ng compound (e.g. silicone caulk) in and around the wire nut or wrap the wires and the wire nuts with electrical tape to prevent moisture from corroding the copper.

If your splice pulls loose, the entire system will fail. Make sure your splice is secure.

1/2" 1/2"

2

1

10 T wists/ft.

8 1-800-732-2677

Additional Boundary Wire

We recommend the use of 20 gauge insulated multi-strand copper wire for direct burial. Extra Boundary Wire can be purchased in 500 foot spools at the store where you purchased the kit or through the

Customer Care Center at 1-800-732-2677.

Note: When adding Boundary Wire, it must act as a continuous loop.

Acres

1/4

1/3

1/2

1

Feet of Wire Needed

415

480

590

835

The table at right indicates the approximate length of Boundary Wire needed for a rectangular, Single Loop layout. Length will vary due to the amount of twisted wire and layout used.

____________________________________________________________________________________________________

Step

4

Connect the Wires to the Fence Transmitter

Boundary Wire (4A)

1. Run the Boundary Wire to the Fence Transmitter through a window, under a door, through a crawl space vent, or any other appropriate available access.

You can also drill a hole through your wall.

2. Strip the ends of the Boundary Wire approximately one-half inch.

3. Insert the Boundary Wires into the Boundary Wire Terminals on the Fence

Transmitter.

4. Turn the Boundary Width Control knob to 10. This will set the Warning Zone at the maximum width.

5. Plug the Power Adapter into the Power Jack and a 120-volt outlet.

6. The Power Light and Loop Indicator Lights should come on. If this does not happen, see the “Troubleshooting” section.

4A

Power

Jack

} Boundary Wire

Terminals

Loop Indicator

Light

Power Light

Boundary Width

Control

Lightning Protection

You may purchase a Lightning Protection Kit through the Customer Care Center at 1-800-732-2677. The

Lightning Protection Kit protects the system against surges that travel through the power source and/or the

Boundary Wire.

____________________________________________________________________________________________________

Step

5

Prepare the Receiver Collar

Your Receiver Collar comes with short Contact Points installed. Use the long Contact

Points for pets with long or thick hair. Tighten the Contact Points with pliers one-half turn beyond finger tight (5A). Check the tightness weekly.

To Insert and Remove the Battery

Note: Do not install the battery while the Receiver Collar is on your pet.

This Receiver Collar utilizes a replaceable PetSafe ® battery (RFA-67). This unique battery is designed to make battery replacement easier and increase water protection.

To insert the battery, align the symbols on the battery (arrow) and Receiver Collar

(triangle) (5B). Use a large coin to turn the battery clockwise until the arrow lines up with the lock symbol on the housing (5C) .

To remove the battery, turn the battery counter-clockwise using a large coin (5D, 5E).

DO NOT attempt to cut into or pry open the battery. Be sure to discard the used battery properly.

A replacement PetSafe ® battery (RFA-67) can be found at many retailers. Contact the Customer Care Center at 1-800-732-2677 or visit our web site at www.petsafe.

net to locate a retailer near you.

www.petsafe.net 9

10

Step

6

Set the Boundary Width and Test the Receiver Collar

The Boundary Control Switch on the side of the

Fence Transmitter has three settings (6A). Setting B is used for most properties. The following table will indicate the setting you should use.

6A

Amount of Wire

Up to 1300 feet

1300-2400

Greater than 2400 feet

Setting

B

C

A

6B

3

2

1

0

4

5

6

7

8

10

9

Use the Boundary Width Control knob to set the width of the Warning Zone and Static Correction

Zone (6B). Set the Boundary Width as wide as possible to give your pet the widest Warning and

Static Correction Zones without reducing the

Pet Area too much.

Note: The Boundary Width Control knob does not change the Static Correction Level.

6C

To identify the Warning and Static Correction

Zones, make sure the Receiver Collar battery is properly installed and the Test Light

Contacts are touching the Contact Points

(6C, 6D). Walk toward the Boundary Wire with Contact Points pointing up and holding the Receiver Collar at your pet’s neck level

(6E) until the Receiver Collar beeps (6F).

Test Light Contacts

3

2

1

0

4

5

6

7

10

9

8

6D

Note: The Receiver Collar is waterproof, which can make the beep hard to hear.

6E 6F 6G

If the Receiver Collar does not beep at the desired range, adjust the Boundary

Width Control knob to the desired setting. Turning the

BoundaryWidth Control knob clockwise increases the Boundary Width while

Boundary

Wire turning it counterclockwise decreases it (6B). Repeat this activity as needed until the Receiver Collar beeps at the desired distance from the Boundary Wire.

Boundary

Wire

The numbers on the Boundary Width Control knob indicate signal strength and are not representative of Boundary

Width footage. If adjusting the Boundary Width Control knob does not give the desired range, adjust the Boundary

Control Switch to another setting to achieve your desired range. If using a Double Loop, you may need to increase the separation of the Boundary Wire to achieve desired range.

The Receiver Collar beeps as a warning tone and ticks when delivering a Static Correction. After hearing the beep, continue to walk towards the wire. The Receiver Collar should tick and the Test Light should fl ash, indicating the

Static Correction as you enter the Static Correction Zone (6G). A warning tone and the fl ashing of the Test Light indicate that the Receiver Collar and the system are working properly and that you are ready to start burying the

Boundary Wire. If the Receiver Collar did not beep or the Test Light did not fl ash, see the “Troubleshooting” section.

Save Test Light for future testing.

Note: The Boundary Width is broken down into 20% Warning Zone and 80% Static Correction Zone.

1-800-732-2677

Step

7

Install the Boundary Wire

To Bury the Boundary Wire

Burying the Boundary Wire is recommended to protect it and prevent disabling the system.

1. Cut a trench 1-3 inches deep along your planned boundary.

2. Place the Boundary Wire into the trench maintaining some slack to allow it to expand and contract with temperature variations.

3. Use a blunt tool such as a wooden paint stick to push the Boundary Wire into the trench. Be careful not to damage the Boundary Wire.

To Attach the Boundary Wire to an Existing Fence

The Boundary Wire of the PetSafe In-Ground Radio Fence™ can be attached to a chain link fence, split rail fence, or a wooden privacy fence. The Boundary Wire can be attached as high as needed. However, make sure the

Boundary Width is set at a high enough range for the pet to receive the signal. If using a Double Loop with an existing fence at least three feet tall, run the Boundary Wire on top of the fence and return it on the bottom of the fence to get the three to fi ve foot separation needed.

• Chain Link Fence (7A): Weave Boundary Wire through the links or use plastic quick ties.

• Wooden Split Rail or Privacy Fence (7A): Use staples to attach Boundary Wire. Avoid puncturing the insulation of the Boundary Wire.

• Gate (Single Loop) (7B) : Bury the Boundary Wire in the ground across the gate opening. Note: The signal is still active across the gate. Your pet cannot pass through an open gate.

7A 7B

WEAVE WIRE INTO FENCE

STAPLE WIRE TO FENCE

STAPLE WIRE

TO FENCE

SINGLE LOOP

www.petsafe.net 11

12

To Cross Hard Surfaces (driveways, sidewalks, etc.)

• Concrete Driveway or Sidewalk

(7D): Place the Boundary Wire in a convenient expansion joint or create a groove using a circular saw and masonry blade. Place the Boundary

Wire in the groove and cover with an appropriate patching compound. For best results, brush away dirt or other debris before patching.

• Gravel or Dirt Driveway (7E): Place the Boundary Wire in a PVC pipe or water hose to protect the Boundary

Wire before burying.

7D 7E

____________________________________________________________________________________________________

Step

8

Place the Boundary Flags

The Boundary Flags are visual reminders for your pet of where the Warning Zone is located.

1. Hold the Receiver Collar at your pet’s neck height.

2. Walk towards the Warning Zone until the

Receiver Collar beeps (8A).

3. Place a Boundary Flag in the ground (8B).

4. Walk back into the Pet Area until the beeping stops.

5. Repeat this process around the Warning

Zone until it is marked with Boundary Flags every 10 feet.

8A 8B

Note: If you cannot hear the beep, see the Test Light

Instructions in Step 6.

____________________________________________________________________________________________________

Step

9

Fit the Receiver Collar

Important: The proper fit and placement of your Receiver Collar is important for effective training. The

Contact Points must have direct contact with your pet’s skin on the underside of his neck.

To assure a proper fit, please follow these steps:

1. Make sure that the battery is not installed in the Receiver Collar.

2. Start with your pet standing comfortably (9A).

3. Center the Contact Points underneath your pet’s neck, touching the skin. If your pet has a long or thick coat, use the enclosed long Contact Points to reach through the hair.

Note: It is sometimes necessary to trim the hair around the Contact Points to make sure that contact is consistent.

9A

1-800-732-2677

4. Check the tightness of the Receiver Collar by inserting one finger between the end of a Contact Point and your pet’s neck. The fit should be snug but not constricting (9B).

5. Allow your pet to wear the collar for several minutes then recheck the fit. Check the fit again as your pet becomes more comfortable with the Receiver Collar.

6. Trim the collar as follows (9C): a. Mark the desired length of the Receiver Collar with a pen. Allow for growth if your pet is young or grows a thick winter coat.

b. Remove the Receiver Collar from your pet and cut off the excess.

c. Before placing the Receiver Collar back onto your pet, seal the edge of the cut collar by applying a flame along the frayed edge.

9B

9C

Important: For comfort, safety and effectiveness of product, please ensure the following:

• During the fi rst 2 weeks of training, do not use the training device on your pet without direct supervision.

• Check the fi t to prevent excessive pressure by being able to insert one fi nger between the Contact Point and your pet’s skin.

• Your pet must be carefully examined daily for any signs of a rash or sore.

• If a rash or sore is observed, discontinue the use of the Receiver Collar for a few days.

• If the condition persists beyond 48 hours, see your veterinarian.

• Your dog’s neck and the Contact Points must be washed weekly with a wash cloth and mild hand soap, then rinsed thoroughly.

A condition called Pressure Necrosis, which is a devitalization of the skin due to excessive and prolonged contact against the Contact Points, may occur if the steps above are not followed.

To Re-Thread the Collar

Slide Buckle

The slide buckle prevents the collar from becoming loose around your pet’s neck.

Ridges

The ridges must be facing up; the collar will slip if it is not properly threaded.

www.petsafe.net 13

Remote Operating Guide

Prepare the Remote Transmitter

To Insert and Remove the Battery

1. Hold the Remote Transmitter face down and pull the battery door open (1A).

2. Insert the 9-volt battery (1B).

3. Replace the battery door by positioning the bottom edge (1C), and snap the battery door into place.

1A 1B 1C

Transmitter Indicator Light – Function and Response

Remote Transmitter

Function

Transmitter Indicator Light

Response

Any button is pressed

Low battery

Solid in color

Flashes every 4 to 5 seconds

___________________________________________________________________________________________________________

Understanding the Remote Transmitter

To train using the Tone Only Button:

The audible sound emitted by the Receiver Collar can be just as effective as the stimulation for some dogs. The Transmitter

Indicator Light will glow for as long as this button is pressed. To use this button for training, simply substitute “Tone Only

Button” whenever “Stimulation Only Button” is used in the Training Guide section.

To train using the Stimulation Only Button:

You control the timing of the stimulation being applied to your pet. The stimulation stays on as long as the Stimulation

Only Button is pressed. If this button is pressed longer than 8 seconds, the Remote Transmitter will “time-out,” the

Transmitter Indicator Light will turn off, and stimulation will no longer be delivered to your pet. This is a safety feature in the Remote Transmitter. If the Remote Transmitter times out, release the Stimulation Only Button and press it again to deliver stimulation.

Note: For either one or both of these training methods to be effective, they must be used consistently along with the command you are trying to teach your pet.

14 1-800-732-2677

Fence Training Guide

Be Patient With Your Pet

Important: Proper training of your pet is essential to the success of the PetSafe In-Ground Radio

Fence™. Read this section completely before beginning to train your pet. Remember that the PetSafe

In-Ground Radio Fence™ is not a solid barrier.

• Have fun with your pet throughout the training process. Training should be fun, fair, firm and consistent.

• Train for 10 to 15 minutes at a time. Don’t try to do too much too quickly. More-frequent short sessions are better than less-frequent longer sessions.

• If your pet shows signs of stress, slow down the training schedule, add additional days of training, or increase the amount of play time with your pet in the Pet Area. Common stress signals include:

- Pet pulling on leash toward the house

- Ears tucked

- Body lowered

- Nervous / frantic movement or stiffening of pet’s body

• Your pet must be completely comfortable near the Boundary Flags at the end of every training session. Spend at least 5 minutes of “play time” at the completion of each session within 10 feet of the Boundary Flags.

• Finish each training session on a positive note with lots of praise and play.

• Remove the Receiver Collar after each training session.

• Be sure to contain your pet by another means during the training period (e.g. pen, tie-out, leash, etc.).

• During training, if you need to take your pet out of the Pet Area, remove the Receiver Collar and either pick your pet up or put him in the car to pass out of the Pet Area.

• Even if you think your pet is responding well to the training, complete the entire training. Reinforcement is important!

____________________________________________________________________________________________________

Days 1 and 2 - Boundary Flag Awareness

Perform three training sessions per day, each lasting 10-15 minutes.

Phase

1

Goal:

To familiarize your pet with the Boundary Flags.

Steps:

1. Begin by walking your pet on a leash in the Pet

Area. Your pet will not wear the Receiver Collar for this training step. Calmly praise and talk to your pet.

2. Move toward the Boundary Flags. Just before your pet’s head reaches the fl ag line (10A), give him a quick horizontal or downward “jerk and release” correction on the leash. Do not correct verbally.

3. Lead your pet back into the Pet Area (10B) to about 15 feet away from the Boundary Flags and praise him.

4. Repeat this process at several different Boundary Flags.

10A 10B

www.petsafe.net 15

16

Days 3 and 4 - Continue Boundary Flag Awareness

Perform three training sessions per day, each lasting 10-15 minutes.

Phase

2

Goal:

To introduce your pet to the Static Correction and teach where it happens.

Setup:

• Place the Receiver Collar on your pet’s neck.

• Put a separate non-metallic collar on your pet’s neck ABOVE the Receiver Collar and attach a leash. Note: Be sure the extra collar does not put pressure on the Contact

Points.

11A

Steps:

1. Walk your pet on a leash in the Pet Area. Calmly praise and talk to your pet.

2. Allow your pet to move toward the Boundary Flags.

3. When your pet enters the Warning Zone, the Receiver Collar will activate and start beeping. As your pet continues past the fl ags into the Static Correction Zone

(11A), he will receive a Static Correction.

4. Immediately after your pet receives a correction, lead him back into the Pet Area.

Praise him warmly and keep very calm body language.

5. Repeat this process at several different Boundary Flags. Never pull or call your pet into the Static Correction Zone. Lead him to the Boundary Flags, and if he decides to not move past the fl ags, he is learning the system.

____________________________________________________________________________________________________

Days 5 thru 8 - Distraction Phase

Perform three training sessions per day, each lasting 10 to 15 minutes.

Phase

3

Goal:

To train your pet to stay within the Pet Area with distractions outside of the Pet Area.

Setup:

• Put a separate non-metallic collar on your pet’s neck ABOVE the Receiver Collar and attach a leash. Note: Be sure the extra collar does not put pressure on the Contact Points.

• Create distractions to tempt your pet to enter the Warning and Static Correction Zones, such as:

- Have a family member cross from inside the Pet Area to outside of it.

- Throw a ball outside of the Pet Area.

- Have a neighbor walk their pet outside of the Pet Area.

Steps:

1. Walk your pet on a leash toward the Boundary Flags. Have a family member walk outside the boundary. If your pet follows, let him feel a correction and quickly lead him back into the Pet Area and praise him. If your pet does not follow the family member, praise him warmly.

2. Have a family member or a neighbor with a dog walk outside the Pet Area paralell to the Boundary Flag line.

Repeat the interaction with your pet as in step 1.

3. With your pet on a leash, throw a ball outside the Boundary Flag line. Again, repeat the interaction with your dog as in previous steps.

4. Repeat distractions at several different Boundary Flags.

1-800-732-2677

Days 9 thru 14 - Unleashed Supervision

Training sessions should start at 10-15 minutes, gradually increasing to over an hour.

Phase

4

Your pet is ready for this step only when he clearly avoids the entire Boundary Flag line, regardless of any distractions or temptations. During this step, do not leave your pet unattended.

Goal:

To give your pet free run of the Pet Area off the leash.

Steps:

1. Walk around the yard and play with your pet, staying within the Pet Area at all times.

2. Preoccupy yourself with another task in the yard while watching your pet.

3. Should your pet escape, take the Receiver Collar off or turn the system off at the

Fence Transmitter and lead him back into the Pet Area.

____________________________________________________________________________________________________

Days 15 thru 30 - Pet Monitoring

Your pet is ready to run! Check in on your pet at regular intervals.

Phase

5

Note: After you are satisfied your pet’s training is complete, remove every other Boundary Flag every 4 days until all flags are removed. Save Boundary Flags for future use.

____________________________________________________________________________________________________

Taking Your Pet Out of the Pet Area

Important: Remove the Receiver Collar and leave it in the Pet Area.

Once your pet learns the Boundary Zone, he will be reluctant to cross it for walks or car rides.

Option 1: Replace the Receiver Collar with a regular collar. Put your pet in a car that is within the Pet Area and drive him out of the Pet Area.

Option 2: Replace the Receiver Collar with a regular collar and leash. Walk your pet out of the Pet Area while giving a command such as “OK” at a specific place of the

Boundary Zone (the end of your driveway, sidewalk, etc.). Always leave the Pet Area with a leash at this place and your pet will associate leaving the Pet Area only on a leash, only at this place, and only with a person. You may initially need to convince your pet to leave the Pet Area with a food treat and lots of praise.

Note: You may also carry your pet out of the Pet Area.

www.petsafe.net 17

Remote Training Guide

General Tips

• Eliminate one misbehavior at a time. If you move too fast with the training, your pet may become confused.

• Be consistent. Give your pet a tone or stimulation with each misbehavior.

• Do not over-correct your pet. Use as few stimulations as possible to train your pet.

• Unless you can supervise him, it is recommended that you restrict your pet from situations in which he has a history of misbehaving. However, setting up a situation as a training session can dramatically improve your chances of success.

• If your pet reacts to the training by hiding or acting fearful, redirect his attention to a simple and appropriate behavior such as the “Sit” command.

• Never use the Remote Trainer to correct or eliminate any form of aggressive behavior. If you are unsure if your dog is aggressive, please consult your veterinarian or a certified trainer.

____________________________________________________________________________________________________________

Eliminating Unwanted Behavior

Jumping Up

Pets typically jump up to get attention. If you do not want your pet to jump on you, then friends or members of the family should not encourage this behavior. That means every time your pet jumps on someone, he should be reprimanded or redirected to an alternate and acceptable behavior, for which he can receive praise.

Note: It is best if your pet first understands the “Sit” command.

1. Put a seperate non-metallic collar on your pet’s neck ABOVE the Receiver

Collar, and attach a leash.

Note: Be sure the extra collar does not put pressure on the Contact Points.

2. As soon as your pet lifts his paws off the ground to jump on you, press the

Stimulation Only Button and give the command “Sit.”

3. Release the Stimulation Only Button immediately once your pet is sitting, and verbally praise him.

4. Practice this exercise in several different areas and use different people for distractions.

___________________________________________________________________________________________________________

Digging

It is important to first understand why your pet is digging. Many dogs, such as terriers, were bred to flush out prey, and digging is very innate to them. Other dogs may be digging to find a cool spot to lie down, or simply out of boredom. Your pet may no longer have the desire to dig if he is provided with the following:

• A cool, shaded area in which to lie down, and plenty of water.

• An alternate activity, such as a favorite toy.

• Plenty of play, exercise, and attention.

• A yard free from rodents or prey that he may be trying to flush out.

18 1-800-732-2677

1. Place the Receiver Collar on your pet and wait at least 10 minutes before placing him in the yard. No other people or pets should be in the yard, as you do not want your pet to associate the stimulation with anything other than his digging. Your pet must be securely fenced in or contained during training.

2. From a window or area where your pet cannot see you, wait until your pet begins to dig.

3. While your pet digs, press the Stimulation Only Button and release it when he stops digging. Only press the button while your pet is in the act of digging, and do not say anything to him.

4. Continue to watch your pet, as he may choose another area to dig.

Trash Raiding

The easiest way to prevent trash raiding is to remove garbage and tempting food from your pet’s environment. You can use the Remote Trainer to teach your pet to stay away from these items; however, you must be prepared to correct your pet every time he approaches them.

1. Pick a temptation for your pet and position yourself where he cannot see you.

2. While your pet’s mouth is touching the temptation, press and hold the Stimulation Only Button. Immediately release the button when your pet leaves the temptation.

3. Do not say anything, as you want your pet to associate the stimulation with his behavior, not you.

4. Repeat this process in several different locations with different temptations.

Excessive Barking

Barking is an instinctive behavior for dogs. It is impossible to keep your dog from barking entirely, but you can teach him be quiet when you give him a command.

Note: This will only be effective when you are at home with your dog.

1. Put your dog in a situation that will tempt him to bark.

2. When your dog begins to bark, press the Stimulation Only Button and give him the command “Quiet.”

3. Immediately release the button once your dog stops barking and praise him.

4. Practice this exercise in different areas using different situations that would cause your dog to bark.

www.petsafe.net 19

Accessories

To purchase additional accessories for your PetSafe In-Ground Radio Fence™, contact the Customer Care Center at

1-800-732-2677 or visit our website at www.petsafe.net to locate a retailer near you.

Component

Battery - two pack

Power Adapter for the Fence Transmitter

Lightning Protection Kit

Replacement Collar

Installation & Training Video (VHS)

Additional Receiver Collar

Super Pet Receiver Collar

Additional Boundary Wire

Additional Boundary Flags

Wire & Flag Accessory Kit

Fence Transmitter

Wire Break Locator

Part Number

RFA-67D-11

RFA-28

RFA-41-1

RFA-146

UL-250BM

RF-275

RFA-1

RFA-2

PRFA-500

RFA-50

Frequently Asked Questions

Is the stimulation safe and humane?

While the stimulation is unpleasant, it is harmless to your pet. Electronic training devices require interaction and training from the owner to achieve desired results.

How old does my pet have to be before using the PetSafe Remote Trainer?

Your pet should be able to recognize basic obedience commands such as

“Sit” or “Stay”. The Receiver Collar may be too large for pets under 8 pounds.

Is the Receiver Collar waterproof?

Yes. When changing the batteries, be sure to keep the area free of dirt and debris. Also, make sure the screws are flush with the Battery Lid.

No. This system is designed for use with one pet only.

Can I use the Remote Trainer with more than one pet?

Can I use the Remote Trainer on aggressive dogs or stop my dog from being aggressive?

Will I get exactly 100 yards of range with the Remote Trainer?

How long can I continuously deliver stimulation to my pet?

What do I do if my pet’s neck becomes red and irritated?

Can I attach a leash to the Receiver

Collar?

We do not recommend any of our products to be used on aggressive dogs.

If you are unsure if your dog is aggressive, please consult your veterinarian or a certified trainer.

The range of the Remote Trainer will vary according to terrain, weather, vegetation, as well as transmission from other radio devices. See “How the

System Works” for tips on maximizing your range.

The maximum amount of time you can press the Stimulation Only Button and deliver stimulation to your pet continuously is 8 seconds. After this, the

Remote Transmitter will time-out, and the Stimulation Only Button must be released and pressed again.

Discontinue use of the Receiver Collar for a few days. If the condition persists beyond 48 hours, see your veterinarian. Once the skin returns to normal, monitor your pet’s skin condition closely.

No. This can result in pulling the Contact Points too tightly against your pet’s neck. Use a separate collar placed above the Receiver Collar to attach a leash.

20 1-800-732-2677

Troubleshooting

Receiver Collar is not beeping or correcting.

The Receiver Collar is beeping, but the pet is not responding to the Static

Correction.

The Receiver Collar has to be held on top of the Boundary Wire to activate.

The Receiver Collar activates inside the house.

I have an inconsistent signal.

The Power and Loop Indicator Lights are off.

The Power Light is on, the Loop

Indicator Light is off, and the Fence

Transmitter loop alarm is sounding.

My pet does not respond when I press the Tone or Stimulation Only Button.

• Check battery to make sure it is installed properly.

• Check that both lights are lit on the Fence Transmitter. If not, perform the “Short Loop Test”.

• Test the Receiver Collar with the Test Light.

• If the Test Light fl ashes, check the fi t of the Receiver Collar.

• Trim your pet’s fur where the Contact Points touch the neck and/or switch to the longer Contact Points.

• Repeat training steps to reinforce training.

• Purchase a stronger Receiver Collar by contacting the Customer Care

Center at 1-800-732-2677.

• Replace battery.

• Adjust Boundary Width Control knob clockwise to increase the distance from the Boundary Wire that the Receiver Collar activates. You can also adjust the Boundary Control Switch to another setting.

• If using a Double Loop, make sure Boundary Wires are separated 3 to 5 feet.

• If the Receiver Collar still has to be held on top of the Boundary Wire, perform the “Short Loop Test.”

• Turn the Boundary Width Control knob counterclockwise to decrease the distance from the Boundary Wire that the Receiver Collar activates.

• Make sure the Boundary Wire is not running too close to the house. The signal can transmit through the walls of your house.

• Make sure Boundary Wires are twisted from Boundary to the Fence

Transmitter.

• Make sure Fence Transmitter is at least 3 feet from large metal objects or appliances.

• Make sure all Boundary Wire turns are gradual.

• Make sure the Boundary Wire is not running parallel to and within 5 feet of electrical wires, neighboring containment systems, telephone wires, television or antenna cables, or satellite dishes.

• If a neighboring containment system may be causing an inconsistent signal, contact the Customer Care Center at 1-800-732-2677 to see if a different frequency system will help your situation.

• Check that the Power Adapter is plugged into the Fence Transmitter.

• Try plugging into another 120-volt outlet.

• If the lights still do not come on, the Fence Transmitter and/or Power

Adapter needs to be replaced. Contact the Customer Care Center at

1-800-732-2677.

• Make sure both ends of the Boundary Wire are plugged into Boundary

Wire Terminals and that ½ inch of the insulation is stripped so that the copper wire is exposed.

• Perform the “Short Loop Test” to determine if the Fence Transmitter needs to be replaced or if the Boundary Wire is broken.

• If the Fence Transmitter is functioning properly, you have a break in your

Boundary Wire. See the “Locating a Break in the Wire” section in this guide.

• Test the Receiver Collar. See “Test Light Instructions.”

• Make sure the Contact Points are placed snugly against your pet’s skin.

• Trim your pet’s fur where the Contact Points touch the neck and/or switch to the longer Contact Points.

www.petsafe.net 21

Additional Information

• The Boundary Wire is buried so that it is not accidentally tripped over or cut. Use care when using a weed eater or when digging near the Boundary Wire to prevent damage.

• The system should only be used with healthy pets. Contact your veterinarian if you have concerns about the medical condition of your pet (medication, pregnant, heart conditions, etc.).

• This system is not for vicious or aggressive pets. If your pet may pose a threat to others, DO NOT USE THIS SYSTEM.

If you are unsure if your dog is aggressive, please consult your veterinarian or a certifi ed trainer.

• The PetSafe In-Ground Radio Fence™ is for residential use only.

• The Static Correction will get your pet’s attention, but will not cause harm. It is designed to startle, not to punish.

• Test the Receiver Collar every 3 to 6 months. Battery life depends upon how often the Receiver Collar is activated.

____________________________________________________________________________________________________________

Short Loop Test

The Short Loop Test is a simple test to determine if each component (Fence Transmitter, Receiver Collar and Boundary

Wire) is functioning properly.

1. Disconnect the Boundary Wire.

2. Cut approximately 10 feet of unused Boundary Wire and connect it to the Boundary Wire Terminals.

3. Attach the Test Light to the Receiver Collar.

4. Spread the Boundary Wire out into a circle. Set the Boundary Control Switch to B.

5. Set the Boundary Width Control knob to 10.

6. If the Loop Indicator Light is not lit, then your Fence Transmitter is not functioning properly. Contact the Customer

Care Center at 1-800-732-2677.

7. If the Loop Indicator Light is lit, disconnect one end of the Boundary Wire from the Boundary Wire Terminal.

8. If the loop alarm does not sound, the Fence Transmitter needs to be replaced. Contact the Customer Care Center at

1-800-732-2677.s

9. If the loop alarm does sound, plug the Boundary Wire back into the Boundary Wire Terminal.

10. Hold the Receiver Collar next to the 10-foot length of Boundary Wire. The Receiver Collar should beep about one foot away from the Boundary Wire. The Test Light should then fl ash as you hold the Receiver Collar closer to the Boundary

Wire.

11. If Receiver Collar does not beep and the Test Light does not fl ash, replace the battery in the Receiver Collar. If it still does not beep and the Test Light does not fl ash, contact the Customer Care Center at 1-800-732-2677.

12. If the Receiver Collar beeps, there may be a complete or partial break in the Boundary Wire. See the “To Locate a Break in the Boundary Wire” section.

___________________________________________________________________________________________________________

To Locate a Break in the Boundary Wire

Please follow these steps in determining where you have a break in your Boundary Wire:

1. Locate your original splice(s) and verify they have a good, solid connection.

2. Check your yard to determine any possible damage to the Boundary Wire (e.g. recent digging, aerating, rodent burrowing, or any other noticeable disturbance in your yard next to the Boundary Wire).

If you still cannot fi nd the break in the Boundary Wire, there are two options for locating it:

Option 1: Contact the Customer Care Center at 1-800-732-2677 to purchase a Wire Break Locator that will locate the break in the Boundary Wire.

22 1-800-732-2677

Option 2: Follow the procedure below:

1. Unplug the Fence Transmitter.

2. Connect both ends of your twisted Boundary Wire to one Boundary Wire

Terminal.

3. Measure and cut a Test Wire which is half the length of your total Boundary

Wire footage.

4. Connect one end of Test Wire to the other Boundary Wire Terminal.

5. Locate the halfway point of your boundary and cut the Boundary Wire.

Test

Wire

6. Splice the other end of the Test Wire to either side of your Boundary Wire where you cut it in half.

7. Plug in the Fence Transmitter and check the Loop Indicator Light. If the Loop

Indicator Light is on, you can assume the break is in the other half of the

Boundary Wire.

8. If the Loop Indicator Light did not come on, you may assume there is a break in this portion of the Boundary Wire. However, there is a small chance of having more than one break in your system. Be sure to check both halves of your entire loop.

9. Replace the damaged Boundary Wire with new Boundary Wire.

10. Reconnect the Boundary Wire to the Fence Transmitter.

11. Check the Loop Indicator Light. If the Loop Indicator Light is on, test the system with the Receiver Collar.

___________________________________________________________________________________________________________

Remote Trainer Testing

1. Hold the Test Light Contacts to the Contact Points

2. Press a Stimulation Button on the Remote Transmitter

3. The Test Light will fl ash.

Note: At higher Intensity Levels the Test Light will fl ash brighter.

Save the Test Light for future testing.

If the Test Light does not fl ash, refer to the Troubleshooting section, or call the

Customer Care Center.

www.petsafe.net 23

Terms of Use and Limitation of Liability

1. Terms of Use

This Product is offered to you conditioned upon your acceptance without modification of the terms, conditions and notices contained herein. Usage of this Product implies acceptance of all such terms, conditions, and notices.

2. Proper Use

This Product is designed for use with pets where training is desired. The specific temperament of your pet may not work with this Product. We recommend that you not use this Product if your pet is less than 8 pounds or if your pet is aggressive. If you are unsure whether this is appropriate for your pet, please consult your veterinarian or certified trainer.

Proper use includes reviewing the entire Guide provided with your Product and any specific Caution statements.

3. No Unlawful or Prohibited Use

This Product is designed for use with pets only. This pet training device is not intended to harm, injure or provoke. Using this Product in a way that is not intended could result in violation of Federal, State or local laws.

4. Limitation of Liability

In no event shall Radio Systems Corporation be liable for any direct, indirect, punitive, incidental, special or consequential damages, or any damages whatsoever arising out of or connected with the use or misuse of this Product.

Buyer assumes all risks and liability from the use of this Product.

5. Modification of Terms and Conditions

Radio Systems Corporation reserves the right to change the terms, conditions and notices under which this Product is offered.

____________________________________________________________________________________________________________

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a practical installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate the interfered receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different to that to which the receiver is connected.

• Contact the Customer Care Center at 1-800-732-2677.

Unauthorized changes or modifi cations to the equipment, not approved by Radio Systems Corporation, could result in not meeting compliance with FCC regulations and could void the user’s authority to operate the equipment.

____________________________________________________________________________________________________________

Caution

The PetSafe In-Ground Radio Fence™ is NOT a solid barrier. The system is designed to act as a deterrent to remind pets by electric stimulation to remain in the boundary established. It is important that you reinforce training with your pet on a regular basis. Since the tolerance level to electrical stimulation varies from pet to pet, Radio Systems Corporation

CANNOT guarantee that the system will, in all cases, keep a pet within the established boundary. Not all pets can be trained to avoid crossing the boundary! Therefore, if you have reason to believe that your pet may pose a danger to others or harm himself if he is not kept from crossing the boundaries, you should NOT rely solely upon the PetSafe In-Ground

Radio Fence™ to confine your pet. Radio Systems Corporation shall NOT be liable for any property damage, economic loss or any consequential damages, sustained as a result of any animal crossing the boundary.

24 1-800-732-2677

www.petsafe.net 25

26 1-800-732-2677

www.petsafe.net 27

Mounting

Template

3.000"

(7.62 cm)

Layout Grid

Radio Systems Corporation

10427 Electric Avenue

Knoxville, TN 37932

1-800-732-2677 www.petsafe.net

400-722

©Copyright 2005, Radio Systems Corporation