CommScope fiber optic cabling systems Field Testing Guidelines

Structured Connectivity Solutions

Field Testing Guidelines for

Fiber-Optic Cabling Systems

February 2013

www.commscope.com

Contents

1. Introduction

2. Passive Link Segments

3. General Testing Guidelines

4. Acceptable Attenuation Values

5. Testing Procedure for Single Fiber Connector Solutions

5.1 Overview

5.2 Relative Power Measurements

5.3 Test Cord Performance Verification

5.4 Link Segment Testing 11

5.4.1 Case 1: Matching Connector Types between Test Equipment and Cabling 11

5.4.2 Case 2: Differing Connector Types Between Test Equipment and Cabling 12

5.5 TIA and ISO/IEC Standards 14

6. Testing Procedure for Solutions Utilizing MPO Connectivity

6.1 Overview

6.2 MPO Case 1: Link with an MPO Trunk Connected to MPO to LC

(or SC, ST) Modules on Each End

6.3 MPO Case 2: MPO Trunk Cable Testing – For 40/100G Applications or When MPO-LC Fan-out Cord Will be Connected at a Later Date

15

15

8

8

8

9

15

7. Troubleshooting

7.1 Cable Plant Defect Detection and Resolution

7.2 Test Equipment Checklist

Appendix A: Encircled Flux Launch Conditions

17

18

18

19

20

Test Instrument Data Sheet

Link Attenuation Measurement Record for Power Meters Displaying

Absolute Power Levels

21

23

5

7

3

4

www.commscope.com

2

1. Introduction

The following guidelines describe CommScope’s recommended procedure for field testing multimode and single-mode cabling systems. CommScope only requires testing of link attenuation for Enterprise networks. While other fiber-optic cabling system parameters such as bandwidth are equally important, they are not normally adversely affected by the quality of the installation and therefore do not require field testing.

This document describes how and where attenuation testing should be performed for Enterprise systems. This issue replaces the previous one dated January 2012. In addition, TIA-568-C.0 and its second addendum, TIA-568-C.0-2, provide standard requirements and guidelines for testing installed optical fiber cabling systems. Optical loss (link attenuation), length verification and polarity testing are defined therein as Tier 1 testing, while OTDR testing is Tier 2 and an optional test.

IMPORTANT NOTE FOR MULTIMODE FIBER TESTING

The fiber optic industry has long understood the importance of a consistent launch condition for accurate and repeatable multimode measurements in both the field and the factory. This has led to mode conditioning of the test cord attached to the light source. For multimode fiber testing in the field, this mode conditioner has traditionally been a mandrel around which the launch cord is wrapped. Standards have recently been updated to specify Encircled Flux (EF) launch conditions. These new requirements are defined in TIA-526-14-B (an adoption of IEC 61280-

04-1ed.2) and normatively referenced in TIA-568-C.0-2 (August 2012), ISO/IEC 11801 and ISO/IEC 14763-3. It is important to note that customers who require compliance to these standards also require the use of EF launch conditions for all multimode cabling attenuation tests. This change was driven by the recognition that loss budgets have diminished as data rates have increased, thus necessitating more precise measurements.

CommScope strongly recommends the use of optical test equipment that provides an Encircled

Flux–compliant launch condition, but at this time EF testing will not be a requirement for

Business Partners requesting the warranty of SySTImAx

®

installations. However if a customer requires TIA adherence, CommScope will not waive the EF testing requirement. CommScope will update these testing requirements as standards and product offerings continue to evolve.

Review appendix A for more information on Encircled Flux.

www.commscope.com

3

2. Passive Link Segments

Attenuation testing should be performed on each passive link segment of the cabling system.

A link segment consists of the cable, connectors, adapters and splices between two fiber-optic termination units (patch panels, information outlets, etc.). Each terminated fiber within a link segment should be tested. The link segment attenuation measurement includes the representative attenuation of connectors at the termination unit interface on both ends of the link, but does not include the attenuation associated with the active equipment interface. This is illustrated in

Figure 1.

Figure 1 Tested Link Segment

www.commscope.com

4

3. General Testing Guidelines

SAFETY NOTE: Unterminated connectors may emit radiation if the far end is connected to a

laser or LED. Do not view the end of a cable until absolutely sure that the fiber is disconnected from any laser or LED source. The best practice is to only view the end face of a connector through a videoscope, so that no direct eye contact to the laser light is possible. Today’s inspection kits are available to view multifiber mPO connectors as well as single-fiber types.

• multimode horizontal link segments should be tested in one direction at EITHER 850 nm or

1,300 nm wavelength.

• multimode backbone and composite link segments should be tested in one direction at

• 850 nm and 1,300 nm wavelengths.

• Single-mode horizontal link segments should be tested in one direction at EITHER 1,310 nm or 1,550 nm wavelength.

• Single-mode backbone and composite link segments should be tested in one direction at

BOTH 1,310 nm and 1,550 nm wavelengths.

Note 1: Horizontal link segments are short enough that attenuation differences caused by

wavelength are insignificant. As a result, single wavelength testing is sufficient. Backbone and composite links may be longer, and attenuation may strongly depend on wavelength in such links. Therefore, it is necessary to test at both wavelengths.

Note 2: The minor attenuation differences due to test direction are on par with the accuracy

and repeatability of the test method. Therefore, testing in only one direction normally suffices.

However, test in both directions if the installation contains fibers of different core sizes. This is to detect inadvertent mixing of fibers with different core sizes, as the loss in one direction will differ from the loss in the other direction by at least 2 dB if different core sizes are connected together (e.g., 50 µm connected to 62.5 µm) when measured using 62.5 µm test cords.

Note 3: Today’s standards only ask for uni-directional Light Source and Power meter (LSPm)

testing, however many customers are requesting bidirectional results. While bidirectional

LSPm testing may provide more data, there is a trade-off with the extra time required and the additional opportunity for dirt and dust to be introduced during the testing process. Bi directional test results are optional; if used, the direction with the higher loss measurement would be used to determine pass/fail for the link.

CommScope recommends multimode field tests to be performed with the Encircled Flux launch condition as defined in TIA-526-14-B and IEC 61280-4-1 ed. 2. Defining a particular launch condition reduces measurement error and variability. This particular launch will produce field measurements that correlate well with component specifications. A mode conditioner device is recommended over the prior mandrel-wrapped cord method. Refer to Appendix A for more information.

www.commscope.com

5

In compliance with TIA/EIA-526-14-B “Optical Power Loss measurements of Installed multimode Fiber Cable Plant”, IEC 61280-4-1 edition 2, “Fibre-Optic Communications

Subsystem Test Procedure – 49 Part 4-1: Installed cable plant – multimode attenuation measurement”, TIA/EIA-526-7 “measurement of Optical Power Loss of Installed Single-mode

Fiber Cable Plant” and IEC 61280-4-2 ed 1 “Fibre optic cable plant – Single-mode fibre optic cable plant attenuation,” the following information should be recorded during the test procedure:

1. Names of personnel conducting the test

2. Type of test equipment used (manufacturer, model, serial number and calibration date*)

3. Date test is being performed

4. Optical source wavelength, spectral width

5. Fiber identification

6. End point locations

7. Test direction

8. Reference power measurement (when not using a power meter with a Relative Power measurement mode)

9. measured attenuation of the link segment

10. Acceptable link attenuation

*Test equipment should be calibrated according to the test equipment manufacturer’s specifications.

See Appendix A for sample measurement recording forms.

IMPORTANT NOTE: Ensure that all connectors/modules are cleaned prior to mating test cords,

trunk cables or patch cords.

Contamination as small as 0.001 mm can block the fiber core generating strong back reflections (low Return Loss) and may affect attenuation (Insertion Loss). mating a contaminated connector to a clean connector will result in poor performance and can transfer contamination and permanently damage the connection. CommScope recommends that fiber optic connectors are inspected with a microscope prior to mating.

Please refer to the CommScope Fiber Optic Connector and Adapter Cleaning Procedures and the CommScope Fiber Optic Connector Cleaning and Inspection kit for more detailed information. Also refer to Section 7 in this document.

www.commscope.com

6

4. Acceptable Attenuation Values

LSPm testing is used to evaluate the overall loss of an entire optical link. Although individual component specifications can be reviewed on each component’s specification sheet, simply adding these values together would likely overestimate the loss of that link. CommScope provides a link loss calculator that shall be used to determine the maximum acceptable loss for each link evaluated. This calculator can be downloaded from the website, www. mycommscope.com or you can consult your local CommScope representative.

Information to be selected or entered in the link loss calculator:

1. Select the fiber type and test wavelength combination from the pull-down menu

2. Select the unit of length in feet or meters from the pull-down menu

3. Enter the total link length under Test

4. Enter the number of connections of each type

5. Enter the number of splices (each Qwik type connections counts as a connection plus a splice).

An example of the format for the SySTImAx

®

Fiber LinkLoss Calculator, available at www.

mycommscope.com, is given in Figure 2. A similar version of the LinkLoss Calculator is available for evaluating the loss of Uniprise

®

systems.

Figure 2

A connection is defined as the joint made by mating fibers terminated with rematable connectors (LC, SC, mPO, etc). For example, an LC connector pair composed of two connectors would count as only one connection within the link loss calculator.

When using the InstaPATCH 360 module, each module actually contains two connection points. This equates to 1 x LC/SC/ST and 1 x mPO per module for the Fiber LinkLoss

Calculator.

The value provided is the maximum acceptable loss allowable to ensure that the solution will meet the performance as described in the CommScope Performance Specifications guides.

Note that this loss will likely be LESS than would be defined by TIA and IEC standards.

Additionally, this value will also likely be LESS than would be calculated by adding the potential maximum loss of all individual components together.

www.commscope.com

7

5. Testing Procedure for Single

Fiber Connector Solutions

5.1 Overview

1. Verify test cord performance (see section 5.2).

2. Obtain a reference power level (see section 5.1).

3. measure link power throughput (see section 5.3).

4. Record link attenuation (see section 5.2).

Two worksheets in the back of these guidelines may be used for recording measurement information.

The first is for use with power meters that display absolute power levels without a selectable reference. The second is for power meters that display power levels relative to a measured reference level. Of course, today most test sets will allow the user to record the data within the test units to access electronically later. Electronic recording is the preferred method of recordkeeping.

5.2 Relative Power measurements

If the power meter supports measurements relative to a reference measurement (in units of dB), select this mode because such readings do not necessitate manual calculation. If the meter does not have a Relative Power measurement mode, perform the following calculation to determine attenuation:

• If P sum

and P ref

are in the same logarithmic units (dBm, dBµ, etc.):

Attenuation (dB) = | P ref

- P sum

• If P sum

and P ref

are in the same linear units (Watts, milliWatts (mW), mircoWatts (µW)):

Attenuation (dB) = | 10 x LOG10 [P ref

/P sum

]|

Where: P sum

is the power reading of the item under test and P reference measurement.

ref

is the power level of the

Caution: Stable reference power levels are critical to the accuracy of subsequent attenuation

measurements. Instability may arise from at least two common causes: battery health and mechanical changes at the connection to the source. Ensure the battery is in good operating condition and fully charged in both the source and power meter. Avoid disturbing the connection in any way from the source to the launch cord after the reference measurement.

Disturbances include disconnection, lateral side-loading, and axial tension. Any of these disturbances is cause for making a new reference measurement. The chances of encountering these disturbances may be minimized by securing the launch cord to the source test set by means of tape or cable tie applied at the launch conditioning device (described later).

CommScope fiber solutions require the use of power meters that accept plugs of the type used to terminate the cabling system under test. CommScope recommends all multimode launch cord performance verifications and link attenuation measurements to be performed with the Encircled

Flux launch condition as defined in TIA-526-14-Band IEC 61280-4-1 ed. 2. See Appendix A for more information.

Caution: Laser light sources, including Vertical Cavity Surface Emitting Lasers (VCSELs), cannot

meet the minimum spectral width requirements defined by TIA-526-14-B for LSPms. Therefore, laser and VCSEL sources are not accepted for certifying multimode fiber systems.

CommScope fiber solutions require all single-mode cord performance verifications and link attenuation measurements to be performed with a launch test cord containing a single loop < 30 mm (1.2 inches) in diameter to suppress multimode propagation. This loop may be created by either wrapping the cord around a mandrel or in free space by securing the cord to itself.

www.commscope.com

8

5.3 Test Cord Performance Verification

In compliance with TIA/EIA-526-14-B and TIA/EIA-526-7 (and IEC equivalents), test cords shall be 1 to 5 meters long and have the same fiber construction (i.e. core diameter and numerical aperture) as the link segment being tested. Before carrying out any test, clean the test cord connectors and test adapter.

Procedure:

1. Prepare the required launch cord with the necessary launch conditioner to meet the

Encircled Flux launch conditions for multimode measurements or mode suppression loop for single-mode measurements.

2. Clean all test cords connectors and the test adapter per the manufacturer’s instructions.

3. Follow the test equipment manufacturer’s initial adjustment instructions.

4. Connect the launch cord between the light source and the power meter. See Figure 3.

Launch cord

Light

Source

Tx Rx

Power meter

Launch conditioner

Figure 3

5. Record the Reference Power measurement (P ref

Relative Power measurement mode.

) or, preferably, select the power meter’s

6. Disconnect the launch cord from the power meter.

7. Connect the receive cord between the power meter and launch cord using the test adapter. See Figure 4.

www.commscope.com

9

Light

Source

Tx

Launch cord

Launch conditioner

Adapter

Receive cord

Rx

Power meter

Figure 4

8. Record the Power measurement (P sum

). Perform the calculations given in section 5.1 if not using Relative Power measurement mode. This measurement provides the attenuation of the receive cord cable (very minimal) plus the connection between the launch and receive cords. The measured attenuation must be less than or equal to the corresponding value given in Table Unacceptable attenuation measurements may be attributable to either of the test cords. Examine each cord with a portable videoscope and clean, polish, or replace if necessary.

9. Flip the ends of the receive cord so that the end originally connected to the power meter is now connected to the adapter and the end originally connected to the adapter is now connected to the power meter.

10. Record the new Power measurement (P sum

). Perform the calculations given in section 5.1 if not using Relative Power measurement mode. The attenuation must be less than or equal to the corresponding value found in Table 1.

TABLE 1 ACCEPTABLE TEST CORD ATTENUATION

Fiber Type

62.5 µm Multimode

LazrSPEED 50 µm

Single-mode

Connection Type Between Test Cords

ST or SC LC

0.30 dB Max

0.30 dB Max

0.55 dB Max

0.20 dB Max

0.20 dB Max

0.30 dB Max

If both measurements are found to be less than or equal to the values found in Table 1, the receive cord is acceptable for testing purposes.

11. Repeat this test procedure from the beginning, reversing the launch and receive cords in order to verify the performance of the launch cord. Remember to remove the existinglaunch conditioner or loop from the former launch cord and apply the same to new launch cord

(formerly the receive cord).

www.commscope.com

10

5.4 Link Segment Testing

5.4.1 Case 1: matching Connector Types between Test Equipment and Cabling

In order to include all connections in the measurement, the One-cord Reference method specified in TIA/EIA-526-14-B (for multimode fibers) and TIA/EIA-526-7 (for single-mode fibers) shall be used to test each link segment. As previously mentioned, in order to perform the onecord reference method, it is necessary that the receptacle on the power meter accept the plug type used on the cabling.

Procedure:

1. Use known test cords, each verified by following the procedure in section 5.2.

2. Prepare the required launch cord with the necessary launch conditioner for multimode measurements or mode suppression loop for single-mode measurements (Launch cord in

Figure 5).

3. Clean the test cord connectors.

4. Follow the test equipment manufacturer’s initial set-up instructions.

5. Connect the launch cord between the light source and the power meter. See Figure 5.

Launch cord

Light

Source

Tx Rx

Power meter

Launch conditioner

Figure 5

6. Record the Reference Power measurement (P ref

) or, preferably, select the power meter’s

Relative Power measurement mode and set the reading to 0.0 dB.

7. Disconnect the launch cord from the power meter and connect it to the receive cord.

Do NOT disconnect the launch cord from the light source. Connect the other end of the receive cord to the meter port. Verify that the connector loss is at or below the value shown in Table 1 above.

8. Separate the launch cord from the receive cord and connect to the ends of the system under test as shown in Figure 6. DO NOT disturb the connection to the source.

www.commscope.com

11

Launch cord

Light

Source

Tx

Launch conditioner

LINK SEGMENT

Splice

Interconnection

Termination Unit:

Patch Panel, Faceplate, etc. w/Adapter

Receive cord

Rx

Power meter

Figure 6

9. Record the power measurement (P sum

) by either performing the calculations given in section

5.1 or, if the meter is in relative power mode, by reading the value directly from the power meter. This measurement provides the attenuation of the link segment cable(s), splice(s) and connections, including the connections on its ends. If the measurement value is less than or equal to the value calculated using the link loss calculator (see section 4), the link segment attenuation is acceptable. If not acceptable see section 7 for troubleshooting guidance.

5.4.2 Case 2: Differing Connector Types Between Test Equipment and Cabling

The One-cord Reference method in TIA/EIA-526-14-B (for multimode fibers) and TIA/EIA-526-7

(for single-mode fibers) assumes the test equipment to have the same connector type as in the link-under test. The three reference cord test method that was outlined in the march 2005

(section 5.2.2) CommScope Fiber Testing Guidelines is no longer needed, except when testing

InstaPATCH

®

trunk cables only (see section 6). This modified adaptation method is necessary when the optical power loss meter receptacle does not mate with the connector of the installed cabling.

Today’s equipment should have a meter port that can be replaced to match the field connector.

This will allow the technician to adjust the connector types as needed to provide a true one-cord reference. Follow the procedures outlined in 5.2.1, changing out the meter port as required to have the appropriate connection type.

Hence, CommScope requires the use of optical power loss meters directly compatible with the plugs installed on the cabling plant.

Note that the cord on the source side is not removed and therefore the source port does not need to be adjustable. A cord with different connector types on each end may be needed to connect to the source port and the field connector.

www.commscope.com

12

Figures 7 and 8 show the test set-up to evaluate an optical link with LC connections and

LC-SC patch cords when the test equipment provided has an SC optical source port and an adjustable meter port.

Figure 8 - System Test

Mode conditioner

Mode conditioner

Meter port adapters should be interchangeable for ease of referencing and testing

Testing an LC system with LC-SC duplex Jumpers:

•LC port needed for referencing

•SC port needed for testing

1-Jumper Reference

Photos courtesy of Fluke ® Network

1. Disconnect from Meter Port

2. Add Test Jumpers at the

Meter and validate mating

3. Test the system

Mode conditioner

Mode conditioner

Photos courtesy of Fluke

®

Network

Figure 7 Reference set-up

www.commscope.com

13

Optimal for this configuration on the ends of the link under test

Adapters on both ends

Plugs on both ends

Plug on one end, adapter on the other

5.5 TIA and ISO/IEC Standards

ISO/IEC 14763-3 covers “Implementation and Operation of Customer Premises Cabling:

Testing of Optical Fiber Cabling” and references.

• IEC 61280-4-1 for installed multimode fiber optic cable plant attenuation measurement

• IEC 61280-4-2 for installed single-mode fiber optic cable plant attenuation measurement

Besides the TIA/EIA-526-14-B and TIA/EIA-526-7 standards already discussed, ANSI/TIA

568-C.0 covers additional guidelines for field testing length, loss and polarity of optical fiber cabling systems.

Table 2 provides the link configurations and the associated reference test methods required by the different standards.

Number of end connection losses included in measurement

2

0

1

TABLE 2 LINk CONFIGURATIONS AND ASSOCIATED REFERENCE TEST mETHODS

Commonly used description

1-cord reference method

3-cord reference method

2-cord reference method

IEC 61280-4-1 ed.2 and ANSI/TIA

526-14-B description

(multimode)

Annex A, One-cord reference method

Annex B, Three-cord reference method

Annex C, Two-cord reference method

IEC 61280-4-2 ed.1 description (single- mode) (Note 1)

Method 1a, One jumper-cable measurement

Method 1c, Three jumper-cable measurement

Method 1b, Two jumper-cable measurement

TIA-526-7 description

(single-mode) (Note 2)

Method A.1,

One jumper-cable measurement

Method A.3,

Three jumper-cable measurement

Method A.2,

Two jumper-cable measurement

Note 1: As of 2011, draft IEC 61280-4-2 edition 2 uses the same descriptions as for multimode.

Note 2: CommScope anticipates that ANSI/TIA-526-7-A will be an adoption of IEC 61280-4-2 edition 2.

The CommScope testing guidelines are in accordance with TIA and IEC 61280-4 series of standards. The one-cord reference method is the most commonly used because most links under test stop at a patch panel on each end and are tested before equipment cords are deployed.

Note that Optical Time Domain Reflectometer (OTDR) test is optional for verifying CommScope enterprise systems.

www.commscope.com

14

6. Testing Procedure for Solutions

Utilizing mPO Connectivity

6.1 Overview

With the inevitable migration to applications using parallel optics technologies such as

40G/100G Ethernet, there is a need to test link segments consisting of mPO array cabling, as seen within the CommScope InstaPATCH

®

360 solution. The mPO connector allows for the consolidation of many fibers within one array. Although typically provided with 12 fibers, an mPO may house eight or 24 fibers less commonly, with other values of fibers possible.

The discussion and figures will focus on 12-F mPO solutions, but the process is relevant to the others.

6.2 mPO Case 1: Link with an mPO Trunk Connected to mPO to LC (or SC, ST) modules on Each End

As you can see in Figure 9, the mPOs are behind the wall and not connected directly to the test cords. If testing two fibers at a time, the technician could test all 12 fibers of the mPO link with six individual tests. In this case, the link can be tested through the single-fiber connections and the testing process follows the procedures outlined in section 5.

170 m (578 ft)

Courtesy of Fluke

®

Network

Figure 9

www.commscope.com

15

Figure 10 MPO-LC harnesses may take the place of MPO-LC modules and LC duplex patch cords

The extra connections do need to be accounted for within the link loss calculator. An mPO to LC (or SC, ST) module will count as two connections on each side because the mPO and single-fiber connections make separate connections. Add one connection for both the singlefiber and mPO connector within the link loss calculator. In contrast, use of an mPO to singlefiber array cord (Figure 8) will only count as one mPO connection because the single-fiber connector will be plugged directly into the electronics. In this case use the three-cord reference measurement described in section 6.3.

In the test shown in Figure 9 above, there are two mPO connections and two LC connections.

An example of how the link loss calculator is used to determine the maximum loss for this link is show in Figure 11.

Figure 11

www.commscope.com

16

6.3 mPO Case 2: mPO Trunk Cable Testing – For

40/100G Applications or When mPO-LC Fan-out

Cord Will be Connected at a Later Date

In this case, there are no single-fiber connectors with which to attach traditional single-fiber test cords. In laboratory or factory settings, there would be test equipment available that could directly attach to mPO connectors. This requires 12 output sources and either 12 input ports or an mPO port with a very wide area detector to accept the light from all 12 (or 24 fibers). This set-up is fairly impractical for field-testing today.

Instead, the technician can use an mPO to LC fan-out cord (See Figure 8) to separate the trunk into single-fiber channels for testing. Because of the additional fan-out cords, a three-cord reference is required to offset the additional loss of the test connections.

The basic steps for performing field attenuation measurements of an mPO trunk are:

1. Verify test cord performance (see section 5.1).

2. Obtain a reference power level with the series of three cords in place per the diagram on the top right of Figure 12.

3. Remove the middle patch cord and add a known good LC to mPO array cord on each side.

4. Attach the mPO-LC cords to the mPO trunk and measure the loss at the first LC per the diagram in the lower left corner of Figure 12.

5. Record and measure the loss at the second LC and continue to the last connection.

Photos courtesy of Fluke

®

Network

Note: EVERY test must measure at or below the maximum value obtained in the link loss calculator in order for the entire MPO link to be acceptable.

Figure 12

www.commscope.com

17

7. Troubleshooting

Link attenuation, exceeding expectations may arise from several reasons. These include contamination, defects in the cable plant, or improper test equipment usage. mPO solutions are particularly susceptible to contamination because of the number of fibers, number of connections and tight loss budgets. Frequent cleaning may be required.

7.1 Cable Plant Defect Detection and Resolution

Contamination is the most common cause of optical loss within connections. For multimode and single-mode cabling, the test cords and the ports under test should be clean and free of damage in accordance with IEC-61300-3-35. Check connector end-faces for dirt and defects

(see Table 3 and Figures 13 and 14, and check link segment for broken fiber, poor splices and tight bends.

TABLE 3

Possible Cause

Adhesive bead left on the tip of a connector

Poorly polished connectors (see Figure 12)

Dirty connectors and/or adapters (see Figure 11)

Broken fiber

Poor mechanical or fusion splices

Excessively tight bends in the cabling

Patch cord does not match the fiber type (compare jacket color and print statement) of the behind-the-wall cabling

Resolution

Examine connectors with a portable microscope and repolish if necessary.

Examine connectors with a portable microscope and repolish if necessary.

Examine connections and clean per manufacturer’s instructions;

Identify break with a Visible Fault Locator or OTDR and splice fiber or replace cable.

Identify poor splices with a Visible Fault Locator or

OTDR and resplice if necessary.

Identify tight bends by inspection or with a Visible Fault

Locator or OTDR and increase the bend radius above minimum specifications.

Replace test leads to match BTW cabling. Reset the reference and retest.

Good and Clean Connector Fingerprint on Connector Dirty Connector

Figure 13

One dirty fiber of an mPO Clean mPO fibers

Pictures courtesy of Fluke Networks

Figure 14

www.commscope.com

18

7.2 Test Equipment Checklist

q

Check Test Cord Conformance

Follow Section 5.3 to verify that the performance of test cords used conform to the values given in Table 1.

q

Check Light Source Conformance

Ensure the source and launch cord combination meets launch condition specifications and the source meets requirements for center wavelength and spectral width according to the standards referenced within section 3.

q

Check Reference Level Stability

Ensure battery-operated equipment batteries are in good condition with sufficient charge.

Ensure that the connection of launch cord to the light source is not disturbed after the reference level measurement. Disturbances include disconnection and reconnection, lateral or axial stresses such as tugging, bumping the connector or bending the cordage. Any of these may

www.commscope.com

19

Appendix A: Encircled Flux

Launch Conditions

IEC 61280-4-1 ed.2 and ANSI/TIA-526-14-B define a precision launch condition used when measuring the attenuation of multimode cabling that uses a metric called Encircled Flux. This metric was established to reduce the measurement variability that is often observed between different test sets because of variations in the launch condition. Reducing this variability is important because loss budgets have become smaller as data rates have increased. Previously defined CPR-plus-mandrel-wrap prescriptions are incapable of assuring sufficiently small variability between test sets, especially when commissioning cabling to support 850 nm applications that operate at data rates above 1 Gb/s.

Encircled Flux compliance is determined using a near-field imaging instrument and analysis software that measures the light distribution at the output end of a test launch cord when transmitting light from the intended test source. Although it is possible to produce a compliant native launch at the output port of the source, a mode conditioning device is typically required between the light source port and the launch test cord output to create a compliant condition.

Reference grade launch cords are generally required to meet the launch specifications.

Reference grade cords and launch conditioning devices may be available from the test set manufacturer. Following the test set manufacturer’s recommendations should produce a compliant launch condition without necessitating actual near-field image verification in the field.

Figure 15 illustrates the use of such mode conditioning devices applied near the output of the sources in a bidirectional test.

Photos courtesy of Fluke

®

Network

Figure 15

www.commscope.com

20

Test Instrument Data Sheet

Manufacturer:

Spectral Width:

850 nm:

1,300 nm:

1,310 nm:

1,550 nm:

Manufacturer:

Model:

LIGHT SOURCE

Serial Number:

Launch Condition Compliance Methodology:

850 nm:

1,300 nm:

1,310 nm:

1,550 nm:

Model:

POWER METER

Serial Number: www.commscope.com

21

Link Attenuation measurement

Record for Power meters

Displaying Absolute Power Levels

Test Personnel: Date:

Light Source Test Location:

Wavelength:

Power Meter Test Location:

Reference Power Measurement (P ref

): Page of

# Fiber

Identification

16

17

18

19

12

13

14

15

20

21

22

23

24

5

6

7

8

1

2

3

4

9

10

11

Power

(P sum

)

Link Seg.

Attn. (dB)

Acceptable

Attn. (dB)

# Fiber

Identification

40

41

42

43

36

37

38

39

44

45

46

47

48

29

30

31

32

25

26

27

28

33

34

35

Power

(P sum

)

Link Seg.

Attn. (dB)

Acceptable

Attn. (dB)

www.commscope.com

22

www.commscope.com

Visit our Web site or contact your local CommScope representative for more information.

© 2013 CommScope, Inc. All rights reserved.

All trademarks identified by

®

or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc.

This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products or services.

II-106524EN (2/13)

Link Attenuation measurement

Record for Power meters

Displaying Absolute Power Levels

Test Personnel: Date:

Light Source Test Location:

Wavelength:

Power Meter Test Location:

Reference Power Measurement (P ref

): Page of

# Fiber

Identification

16

17

18

19

12

13

14

15

20

21

22

23

24

5

6

7

8

1

2

3

4

9

10

11

Link Seg.

Attn. (dB)

Acceptable

Attn. (dB)

# Fiber

Identification

40

41

42

43

36

37

38

39

44

45

46

47

48

29

30

31

32

25

26

27

28

33

34

35

Link Seg.

Attn. (dB)

Acceptable

Attn. (dB)

www.commscope.com

23