advertisement
15P1200Nd
P1200/Nd Series
KEY FEATURES
• Real 1200 W AES power handling
• Sensitivity: 97 dB @ 2.83V
• 4” duo technology voice coil
• Forced air convection circuit for low power compression
• Extended controlled displacement: Xmax ± 9.5 mm.
• Massive mechanical displacement capability: 52 mm p-p
GENERAL DESCRIPTION
This model is the result of an extensive and intense research of every single constituent part of an electro-dynamic loudspeaker, rethinking the basics and taking care of every detail, to withstand the extreme power conditions it has been designed to work in.
All this investigation is reflected in the new and innovative technologies developed by Beyma and applied in this new transducer.
DUO TECHNOLOGY 4” VOICE COIL
• Laminated former combining two different advanced technology materials to enhance the voice coil life.
• Voice coil winding coiled over the two faces of the former.
• Double insulation paper (inner and outer) for optimum force transmission.
• Superficial treatment of the voice coil winding to provide further protection to the voice coil wire.
MOVING ASSEMBLY
• High stiffness weather resistant paper cone.
• Beyma Double Conex Spider technology (D.C.S.): the conex is a fireproof material that insures the preservation of the spider mechanical properties under extreme power conditions.
• Beyma Mechanical Mirror Suspension System
(M.M.S.S.): the diaphragm surround and the double spider have been carefully designed with the assistance of
Finite Element calculations in order to match coherently, enabling long and controlled cone displacements.
HEAT DISSIPATION
• Low power compression due to the use of a forced convection mechanism.
• This design has been optimized with the extensive use of miniature high temperature probes and real-time temperature acquisition systems, together with a thermographic camera to obtain real images of the heat distribution in the voice coil and forced convection effects.
UNDER-POLE NEODYMIUM MAGNET TOPOLOGY
• F.E.A. optimized under-pole magnet topology. This geometry maximizes the flux density in the air-gap and completely eliminate the leakage magnetic field, avoiding any possible magnetic interference with other equipment.
• High temperature neodymium magnets.
FREQUENCY RESPONSE AND DISTORTION CURVES FREE AIR IMPEDANCE CURVE
Note: on axis frequency response measured with loudspeaker standing on infinite baffle in anechoic chamber, 1w @ 1m.
TECHNICAL SPECIFICATIONS
Nominal diameter
Rated impedance
Minimum impedance
Power capacity*
Program power
Sensitivity
Frequency range
Recom. enclosure vol.
Voice coil diameter
Magnetic assembly weight
BL factor
Moving mass
Voice coil length
Air gap height
X damage (peak to peak)
380 mm. 15 in.
8 ohms
6.1 ohms
1200 w AES
2400 w
97 dB 2.83v @ 1m @ 2 p
30 - 2000 Hz
40 / 150 l 1.4 / 5.3 ft.
3
100 mm. 4 in.
6 kg. 13.2 lb.
26.3 N / A
0.150 kg.
25 mm
14 mm
52 mm
MOUNTING INFORMATION
Overall diameter
Bolt circle diameter
Baffle cutout diameter:
- Front mount
- Rear mount
Depth
Volume displaced by driver
Net weight
Shipping weight
388 mm. 15.28 in.
370 mm. 14.57 in.
352 mm. 13.86 in.
355 mm. 13.98 in.
155 mm. 6.10 in.
7 l 0.25 ft.
3
7.7 kg. 16.94 lb.
8.7 kg. 19.14 lb.
THIELE-SMALL PARAMETERS**
Resonant frequency, fs
D.C. Voice coil resistance, Re
Mechanical Quality Factor, Qms
Electrical Quality Factor, Qes
Total Quality Factor, Qts
Equivalent Air Volume to Cms, Vas
Mechanical Compliance, Cms
Mechanical Resistance, Rms
Efficiency, hhhhho (%)
Effective Surface Area, Sd (m 2 )
Maximum Displacement, Xmax***
Displacement Volume, Vd
Voice Coil Inductance, Le @ 1 kHz
45 Hz
5.3 ohms.
7.73
0.33
0.31
84 l
81 mmmmmm / N
5.7 kg / s
2.3
0.0855 m 2
9.5 mm
815 cm 3
2.3 mH
15P1200Nd
P1200/Nd Series
DIMENSION DRAWINGS
POWER COMPRESSION LOSSES
6,0
5,0
4,0
3,0
2,0
1,0
0,0
100 200 300 400 500 600 700 800 900 1000 1100 1200
Power (W)
Note: These losses are calculated from a five minutes AES power test applying band limited pink noise (50-500 Hz). The loudspeaker is free-air standing.
MATERIALS
• Basket: Cast aluminium
• Cone: Paper
• Surround: Treated cloth
• Voice coil: Copper wire
• Magnet: Neodymium
Notes:
*The power capacity is determined according to AES2-1984 (r2003) standard.
Program power is defined as the transducer’s ability to handle normal music program material.
**T-S parameters are measured after an exercise period using a preconditioning power test.
The measurements are carried out with a velocity-current laser transducer and will reflect the long term parameters (once the loudspeaker has been working for a short period of time).
***The Xmax is calculated as (Lvc - Hag)/2 + Hag/3.5, where Lvc is the voice coil length and Hag is the air gap height.
Polígono Industrial Moncada II · C/. Pont Sec, 1c · 46113 MONCADA - Valencia (Spain)
· Tel. ( 34 ) 96 130 13 75 · Fax ( 34 ) 96 130 15 07 · http://www.beyma.com · E-mail: [email protected] ·
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project