BLUE FLAME VENT-FREE

NATURAL GAS SPACE

HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

Do not store, or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS l Do not try to light any appliance.

l Do not touch any electrical switch; do not

use any phone in your building.

l Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

l If you cannot reach your gas supplier, call

the fire department.

Installation and service must be performed by a qualified installer, service agency or gas supplier.

MN200HBA MN200TBA

MN300HBA MN300TBA

Table of Contents

Important Safety Information.................................2

Product Features.....................................................3

Proper Ventilation & Fresh Air...............................4

Installation................................................................6

Operating Your Heater...........................................10

Cleaning & Maintenance.......................................13

Trouble Shooting...................................................14

Specifications..........................................................17

Parts List.................................................................19

WARNING: If the information in this

manual is not followed exactly, a f i r e o r e x p l o s i o n m a y r e s u l t causing property damage, personal injury, or loss of life.

WA RN I N G : I m p r o p e r in s t a l l a t i o n ,

adjustment, alteration, service or maintenance can cause injury or property damage.

Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or gas supplier.

This appliance may be installed in an aftermarket* permanently located, manufactured

(mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

WARNING: This is an unvented gas-fired

heater. It uses air (oxygen) f r o m t h e r o o m i n w h i c h i t i s installed. Provisions for adequate combustion and ventilation air must b e p r o v i d e d . R e f e r t o A i r F o r Combustion and Ventilation section on page 4 of this manual.

CONTINENTAL APPLIANCE INC/U.S. OFFICE

5 Musick 4600 Highlands Parkway S.E

.

Irvine Suite # D/E

CA 92618 Smyrna, GA 30080

Nanjing PRO-COM Electric Appliance Co.,Ltd.

#6 Chuangye Road,High New Tech.Zone,

Great Bridge Road North,Nanjing,210061,

China.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.

WATER VAPOR: A BY-PRODUCT OF UNVENTED

ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one

(1) ounce (30ml) of water for every 1,000 BTU’s

(.3KW’s) of gas input per hour. Refer to page 3.

Installer: Please leave these instructions with the consumer.

Consumer: Please retain these instructions for future use.

TOLL-FREE PHONE NUMBER: (877)886-5989

PR-ML062-07-0803

IMPORTANT

SAFETY INFORMATION

WARNINGS

IMPORTANT: Read this owner’s manual carefully and c o m p l e t e l y b e f o r e t r y i n g t o assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, f i r e , e x p l o s i o n , e l e c t r i c a l shock, and carbon monoxide poisoning.

WARNING: Do not use any accessory not approved for use with this heater.

WARNING: Any change to this heater or its controls can be dangerous.

Do not place clothing or other flammable material on or near the appliance. Never place any objects on the heater.

Due to high temperatures, heater s h o u l d b e k e p t o u t o f traffic and away from furniture and draperies.

Surface of heater becomes very hot when running heater.

Keep children and adults away from hot surface to avoid burns or clothing ignition. Heater will remain hot for a time after shuting down. Allow surface to cool before touching.

C a r e f u l l y s u p e r v i s e y o u n g children when they are in the same room with heater.

Make sure grill guard is in place before running heater.

Keep the appliance area clear a nd fr e e f r o m co m b us t i bl e materials, gasoline, and other flammable vapors and liquids.

WARNING

Modeles MN200HBA, MN300HBA,

MN200TBA, MN300TBA are equipped for natural gas. Field conversion is not permitted.

State of Massachusetts:

The installation must be made by a licensed plumber or gas fitter in the

Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

In the state of Massachusetts, unvented propane or nature gas-fired space heaters shall be prohibited in bedrooms and bathrooms.

1. This appliance is only for use

with the type of gas indicated

on the rating plate. This

appliance is not convertible for

use with other gases.

2. If you smell gas l Shut off gas supply.

l Do not try to light any appliance.

l Do not touch any electrical switch;

do not use any phone in your

building.

l Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

l If you cannot reach your gas

supplier, call the fire department.

3. This heater shall not be

installed in a bedroom or

bathroom.

4. This heater needs fresh,

outside air ventilation to run

properly. This heater has an

Oxygen Depletion Sensor

(ODS) safety shutoff system.

The ODS shuts down the

heater if not enough fresh air

is available. See Fresh Air for

Combustion and Ventilation

pages 4 and 5.

5. Keep all air openings in front

and at the bottom of heater clear

and free of debris. This will

insure enough air for proper

combustion.

6. If heater shuts off. Do not

relight until you provide fresh,

outside air. If heater keeps

shutting off, have it serviced.

7. Do not operate heater l where flammable liquids or vapors

are used or stored l under dusty conditions

8. Turn heater off before using

furniture polish, wax, carpet

cleaner, or similar products. If

heated, the vapors from these

products may create a white

powder residue within burner

box or on adjacent walls or

furniture.

9. Do not use heater if any part

has been under water

Immediately call a qualified

service technician to inspect

the room heater and to replace

any part of the control system

and any gas control which has

been under water.

10. Turn off heater and let cool

before servicing. Only a quali

fied service person should

service and repair heater.

11. Operating heater above eleva

tions of 4,500 feet could cause

pilot outage.

DANGER: Carbon monoxide poisoning may lead to death!

Carbon Monoxide Poisoning.

Early signs of carbon monoxide poisoning resemble the flu with headaches, dizziness, or nausea

If you have these signs, the heater may not be working properly. Get

fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, persons with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.

Natural Gas: Natural gas is odorless. An odor-making agent is added to natural gas. The odor helps you detect a natural gas leak .

However, the odor added to natural gas can fade. Natural gas may be present even though no odor exists.

Make certain you read and unders t a n d a l l w a r n i n g s . K e e p this manual for reference. It is your guide to safe and proper operation of this heater.

2

PRODUCT FEATURES

Figure1-Vent-Free Natural Gas Heater

SAFETY DEVICE

A standard requirement for all vent-free room heaters. This heater has a pilot with an Oxygen

Depletion Sensor(ODS) safety shutoff system.

The ODS/pilot shuts off the heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater is equipped with a piezo ignitor.

This system requires no matches, batteries, or other sources to light heater.

LOCAL CODES

Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of National Fuel Gas Code ANSZ223.1, also known as NFPA 54*.

*Available from :

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

THERMOSTATIC HEAT

CONTROL ON THERMOSTAT

MODELS

These heaters have a control valve with a thermostat sensing bulb. This results in the greatest heater comfort and may result in lower gas bills.

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging applied to

heater for shipment.

3. Check heater for any shipping damage. If heater

is damaged. promptly inform dealer where you

bought heater.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one

(1) ounce (30ml) of water for every 1,000 BTU’s

(.3KW’s) of gas input per hour.

Unvented room heaters are recommended as supplemental heat (a room) rather than a primary heat source (an entire house). In most supplemental heat applications, the water vapor does not create a problem. In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather.

The following steps will help insure that water vapor does not become a problem.

1. Be sure the heater is sized properly for the application, including ample combustion air and circulation air.

2. If high humidity is experienced, a dehumidifier may be used to help lower the water vapor content of the air.

3. Do not use an unvented room heater as the primary heat source.

3

FRESH AIR FOR

COMBUSTION AND

VENTILATION

WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and v e n t i l a t i o n a i r . R e a d t h e f o l l o w i n g i n s t r u c t i o n s t o insure proper fresh air for this and other fuel-burning appliances in your home.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from

National Fuel Gas Code. NFPA 54/

ANS Z223.1, Section 5.3. Air for

Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will help you classify your space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation.

However, in buildings of unusually tight construction, l you must provide additional fresh air.

Unusually tight construction is defined as construction where: a. walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of one perm (6 × 10 -11 kg per pa-sec-m 2 ) or less with openings gasketed or sealed and b. weather stripping has been added on openable windows and doors and c. caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings. If your home meets all of the three criteria above, you must provide additional fresh air.

See Ventilation Air From Outdoors, page 6.

If your home does not meet all of the three criteria abov, see Determining

Fresh-Air Flow for Heater Location, page 4, 5.

Confined and

Unconfined Space

The National Fuel Gas Code ANS

Z223.1 defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m 3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m 3 per kw) of the aggregate input rating of all appliances installed in that space.

Rooms communicating directly with t h e s p a c e i n w h i c h t h e appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.

This heater shall not be installed in a confined space or unusually t i g h t c o n s t r u c t i o n u n l e s s provisions are provided for adequate combustion and ventilation air.

* A d j o i n i n g r o o m s a r e communicating only if there are doorless passageways or ventilation grills between them.

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if you Have a Confined or Unconfined Space*

Use this worksheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space (length

Length

× width × height).

× Width × Height= cu.ft. (volume of space)

Example: Space size 20ft. (length) × 16ft.( width) × 8ft. (ceiling height)=2560cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

(volume of space)

÷

50 cu. ft.=(Maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space)

÷

50 cu.ft.=51.2 or 51,200(maximum Btu/Hr t he space can support)

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Coda, ANS Z223.1, Section 5.3

or applicable local codes.

4

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater Btu/Hr

Gas water heater* Btu/Hr

Gas furnace Btu/Hr

Vented gas heater Btu/Hr

Gas Fireplace logs Btu/Hr

Other gas appliances* + Btu/Hr

Total = Btu/Hr

Example:

Gas water heater 40,000 Btu/Hr

Vent free heater + 20,000 Btu/Hr

Total = 60,000 Btu/Hr

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and

vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

Btu/Hr (maximum the space can support)

Btu/Hr (actual amount of Btu/Hr used)

Example : 51,200 Btu/Hr(maximum the space can support)

60,000 Btu/Hr(actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.

You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air from

Inside Building, page 5.

B. Vent room directly to the outdoors. See Ventilation Air from Outdoors, page 6 .

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no additional fresh air ventilation.

AIR FOR COMBUSTION AND VENTILATION

Continued

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12 and one within 12

"

of the ceiling

"

of the floor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National

Fuel Gas Code NFPA 54/ANS Z223.1.

Section 5.3, Air for Combustion and

Ventilation for required size of ventilation grills or ducts

WARNING: Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces.

Figure 2 -Ventilation Air from Inside Building

5

VENTILATION AIR

Figure 3 -Ventilation Air from Outdoors

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater. as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualified service person must install heater. Follow all local codes.

CHECK GAS TYPE

Use only natural gas. If your gas supply is not natural, do not install heater. Call dealer where you bought heater for proper type heater.

INSTALLATION NEEDS

Before installing heater, make sure you have the items listed below.

l piping (check local codes) l sealant (resistant to natural gas) l equipment shutoff valve* l ground joint union l test gauge connection* l sediment trap l tee joint l pipe wrench

*A CSA/AGA design-certified equip-ment shutoff valve with 1/8

"

NPT tap is an acceptable a l t e r n a t i v e t o t e s t g a u g e connection. Purchase the optional

CSA/AGA design certified equipment shutoff valve from your dealer. See Accessories, page 17.

LOCATING HEATER

This heater is designed to be mounted on a wall. You can locate heater on floor, away from a wall.

An optional floor mounting stand is needed. Purchase the floor mounting stand from your dealer.

See Accessories, page 17.

For convenience and efficiency, install heater l where there is easy access for

operation, inspection, and service l in coldest part of room

An optional fan kit is available from your dealer. See Accessories, page 17. If planning to use fan, locate heater near an electrical outlet.

CAUTION: If you install the heater in a home garage l heater pilot and burner must

be at least 18 inches above

floor.

l locate heater where moving

vehicle will not hit it.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts: You must provide two permanent openings: one within 12

12

"

of the ceiling and one within

"

of the floor.

Connect these items directly to the outdoors or spaces open to the outdoors.

These spaces include attics and crawl spaces. Follow the National Fuel Gas

Code NFPA 54/ANS Z223.1, Section 5.3.

Air for Combustion and Ventilation for required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled power vent.

Heated air entering the attic will activate the power vent.

CAUTION: This heater creates warm air currents.

These currents move heat to wall surfaces next to h e a t e r . I n s t a l l i n g h e a t e r next to vinyl or cloth wall c o v e r i n g s o r o p e r a t i n g heater where impurities (such as tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist may discolor walls.

WARNING: Never install the heater l in a bedroom or bathroom.

l in a recreational vehicle.

l where curtains, furniture,

clothing, or other flammable

objects are less than 36 inches

from the front, top, or sides of

the heater.

l as a fireplace insert.

l in high traffic areas.

l in windy or drafty areas.

6

WARNING: Maintain the minimum clearances shown i n F i g u r e 4 . I f y o u c a n , provide greater clearances from floor, ceiling, and joining wall.

INSTALLATION

FASTENING HEATER TO WALL

Mounting Bracket

The mounting bracket is located on back panel of heater (see figure 6). It has been taped there for shipping. Remove mounting bracket from back panel.

Figure 6 -Mounting Bracket

Location

Removing Lower Front Panel Of

The Heater

1. Remove two screws near bottom

corners of lower front panel

2. Pull bottom of lower front panel

forward, then down (see Figure 7).

Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls

(wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1. Tape mounting bracket to wall where heater will be located.

Make sure mounting bracket is level.

WARNING: Maintain minimum clearances shown in

Figure 8. If you can, provide greater clearances from floor and joining wall.

Figure 4 -Mounting Clearance as

Viewed From Font Of Heater

IMPORTANT: Vent-free heaters add moisture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See

Fresh Air for Combustion and

Ventilation, pages 4 and 5.

INSTALLING THERMOSTAT

SENSING BULB

For T-Stat Models Only

1. Pull out the sensing bulb from the

two clips located in the shippng

position according to the direction

as shown by the arrow. There is no

need to take out the two bulb clips.

2. Take out the bulb clip from the

hardware package and insert it into

the square hole and then insert the

sensing bulb into the bulb clip (see

Figure 5).

Figure 7 - Removing Lower Front

Panel Of Heater

Methods For Attaching Mounting

Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes are 16 inches apart from center.

Attach mounting bracket to wall o n l y i n o n e o f t w o w a y s :

1. Attaching to wall stud

2. Attaching to wall anchor

Attaching To Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Figure 5 - Moving Thermostat

Sensing Bulb

2. Mark screw locations on wall. (see Figure 8)

Note: Only mark last hole on each end of mounting bracket.

Insert mounting screws through these holes only.

3. Remove tape and mounting bracket from wall.

Model MN300HBA MN300TBA

Model MN200HBA MN200TBA

Figure 8 - Mounting Bracket

Clearances

7

INSTALLATION

Attaching Mounting Bracket to

Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hardware package is provided with heater.

Attaching To Wal l Stud Method

For attaching mounting bracket to wall studs

1. Drill holes at marked locations

using 9/64

"

drill bit.

2. Place mounting bracket onto

wall. Line up last hole on each

end of bracket with holes drilled

in wall.

3. Insert mounting screws through

bracket and into wall studs.

4. Tighten screws until mounting

bracket is firmly fastened to

wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)

1. Drill holes at marked locations

using 5/16

"

drill bit. For solid

walls (concrete or masonry),

drill at least 1

"

deep.

2. Fold wall anchor as shown in

Figure 9 below.

IMPORTANT: Do not hammer key! For thick walls

(over 1/2

"

thick) or solid walls, do not pop open wings.

Figure 10 - Popping Open Anchor

Wing For Thin Walls

5. Place mounting bracket onto

wall. Line up last hole on

each end of bracket with wall

anchors.

6. Insert mounting screws through

bracket and into wall anchors.

7. Tighten screws until mounting

bracket is firmly fastened to

wall.

Placing Heater On Mounting

Bracket

1. Locate two horizontal slots on

back panel of heater (see

Figure 11).

2. Place heater onto mounting

bracket. Slide horizontal slots

onto stand-out tabs on

mounting bracket.

Figure 12 - Installing Bottom

Mounting Screws

2. Mark screw locations on

wall.

3. Remove heater from mounting

bracket.

4. If installing bottom mounting

screws into hollow or solid wall,

install wall anchors. Follow steps

1 through 4 under Attaching To

Wall Anchor Method. If installing

bottom mounting screw into

wall stud, drill holes at marked

locations using 9/64

"

drill bit.

5. Replace heater onto mounting

bracket.

6. Place spacers between

bottom mounting holes and

wall anchor or drilled holes.

7. Hold spacer in place with one

hand. With other hand, insert

mounting screw through

bottom mounting hole and

spacer. Place tip of screw in

opening of wall anchor

or drilled holes.

8. Tighten both screws until heater

i s f i r m l y s e c u r e d t o

wall. Do not over tighten.

l Note: Do not replace front panel

at this time. Replace front

panel after making gas

connections and checking for

leaks (see pages 8 and 9).

Figure 9 - Folding Anchor

3. Insert wall anchor (wings

first) into hole. Tap anchor

flush to wall.

4. For thin walls (1/2

"

or less),

insert red key into wall

anchor. Push red key to

" pop

"

open anchor wings.

(see Figure 10).

Figure 11 - Mounting Heater Onto

Mounting Bracket

Installing Bottom Mounting

Screws

1. Locate two bottom mounting

holes. These holes are near

bottom on back panel of

heater(see Figure 12).

8

INSTALLATION

CONNECTING TO GAS SUPPLY

WARNING: A qualified service person must connect heater to gas supply. Follow all local codes.

WARNING: This appliance requires a 3/8

"

NPT (National

Pipe Thread) inlet connection to the pressure regulator.

WARNING: Never connect heater to private (non-utility) gas well. This gas is commonly known as well-head gas.

IMPORTANT: Check your gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 10.5 inches of water. If gas line pressure is higher, heater regulator damage could occur.

CAUTION: Use only new, b l a c k i r o n o r s t e e l p i p e .

Internally-tinned copper tubing may be used in certain areas.

Check your local codes. Use pipe of large enough diameter to allow proper gas volume to heater.

If pip e is too small, undue loss of pressure will occur.

Typical Inlet Pipe Diameters

All models up to 20,000 BTU’s use

3/8’’ or greater pipe;

All models 25,000 BTU’s and higher, use 1/2” or greater pipe.

Installation must include an equipment shutoff valve, union, and plugged 1/8

"

NPT tap. Locate

NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure

13).

Figure 13 -Gas Connection

*A CSA/AGA design-certified equipment shutoff valve with 1/8

"

NPT tap is an acceptable alternative to test gauge connection. Purchase the optional

C S A / A G A d e s i g n - c e r t i f i e d e q u i p m e n t s h u t o ff v a l v e f r o m your dealer. See Accessories, page 17.

IMPORTANT: Install an equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.

Install sediment trap in supply line as shown in Figure 13. Locate sediment trap where it is within reach for cleaning. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

CAUTION: Use pipe joint sealant that is resistant to natural gas.

IMPORTANT: Hold pressure regulator with wrench when connecting it to gas piping and/or fittings.

9

CHECKING GAS

CONNECTIONS

WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once.

WARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.

Pressure Testing Gas Supply

Piping System

Test Pressures In Excess Of

1/2 PSIG (3.5 K Pa)

1. Disconnect appliance with its

appliance main gas valve

(control valve) and equipment

shutoff valve from gas supply

piping system. Pressures in

excess of 1/2 psig will damage

heater regulator.

2. Cap off open end of gas pipe where equipment shutoff valve

was connected.

3. Pressurize supply piping s y s t e m b y e i t h e r u s i n g compressed air or opening main gas valve located on or

near gas meter.

4. Check all joints of gas supply piping system. Apply mixture of liquid soap and water to gas joints. Bubbles forming show

a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment

shutoff valve to gas supply. Check reconnected fittings for leaks.

Test Pressures Equal To or

Less Than 1/2 PSIG (3.5 K Pa)

1. Close equipment shutoff valve

(see Figure 14).

2. Pressurize supply piping system

by either using compressed air

or opening main gas valve

located on or near gas meter.

3. Check all joints from gas meter to

equipment shutoff vane (see

Figure 15). Apply mixture of

liquid soap and water to gas

joints. Bubbles forming show

a leak.

4. Correct all leaks at once.

INSTALLATION

Pressure Testing Heater Gas

Connections

OPERATING YOUR HEATER

THERMOSTAT MODELS

1. Open equipment shutoff valve

(see Figure 14).

2. Open main gas valve located

on or near gas meter.

3. Make sure control knob of

heater is in the OFF position.

4. Check all joints from equipment

shutoff valve to control valve

(see Figure 15 ). Apply mixture of

liquid soap and water to gas

joints. Bubbles forming show

a leak.

5. Correct all leaks at once.

6. Light heater (see Operating

Heater, pages 10 and 11 for thermostat models or page 12 for non-thermostat models).

Check the rest of the intemal

joints for leaks.

7. Turn off heater (see To Turn Off

Gas to Appliance, page 11 for thermostat models or page 12

for non-thermostat models).

8. Replace lower front panel.

n

FOR YOUR SAFETY

n

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may r e s u l t c a u s i n g p r o p e r t y damage, personal injury or loss of life.

A. When lighting the pilot, follow

these instructions exactly.

B. BEFORE LIGHTING smell all

around the appliance area for

gas. Be sure to smell next to

the floor because some gas is

heavier than air and will settle

on the floor .

Figure 14 -Equipment Shutoff Valve

WHAT TO DO IF YOU SMELL GAS l Do not try to light any appliance.

l Do not touch any electric switch;

do not use any phone in your

building.

l Immediately call your gas

supplier from a neighbor’s

phone. Follow the gas

supplier’s instructions.

l If you cannot reach your

gas supplier, call the fire

department.

Figure 15 -Checking Gas Joints

WARING

:

Do not over tighten gas

connections.

C. Use only your hand to push in

or turn the gas control knob.

Never use tools. If the knob

will not push in or turn by

hand, don’t try to repair it, call

a qualified service technician or

gas supplier. Force or attempted

repair may result in a fire or

explosion.

D. Do not use this appliance if any

part has been under water.

Immediately call a qualified

service technician to inspect

the appliance and to replace

any part of the control system

and any gas control which has

been under water.

1 0

THERMOSTAT MODELS

n LIGHTING n

INSTRUCTIONS

1. STOP! Read the safety

information on the side of

heater.

2. Check that gas supply to

heater is on.

3. Push in gas control knob

slightly and turn clockwise

to the OFF position.

NOTE: knob cannot be turned from

“PILOT” to “OFF” unless knob is pushed in slightly. Do not use force.

4. Wait five (5) minutes to clear

out any air. Then smell for

gas, including near the floor.

If you smell gas, STOP!

Follow “B” in the safety

information on the side of the

heater. If you do not smell

gas, go to the next step.

5. Push in gas control knob

slightly and turn

counterclockwise to

“PILOT/IGN” and depress for

five(5) seconds

NOTE: The first time that the h e a t e r i s o p e r a t e d a f t e r connecting the gas supply , the control knob should be depressed for about thirty (30) seconds. This will allow air to bleed from the gas system.

OPERATING YOUR HEATER

7. Keep control knob pressed in

for thirty (30) seconds after

lighting pilot. After 30

seconds, release control knob.

l If control knob does not pop

up when released, contact a

qualified service person or

gas supplier for repairs.

This increases or decreases the burner flame height. At times the room may exceed the set temperature. If so, the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set to any heat level between HI and LO. Selecting the HI setting will cause the burner to remain fully on without modulating down in most cases.

NOTE: If pilot goes out, repeat steps 3 through 7. Wait one (1) minute before lighting pilot again

8. Turn control knob

counterclockwise to

desired heating Level. The

main burner should light. Set

control knob to any heat level

between HI and LO.

NOTE: the thermostat sensing bulb measures the temperature of air near the heater cabinet. This may not always agree with room temperature

(depending on housing construction.

installation location, room size, open air temperatures, etc.). frequent use of your heater will let you determine

your own comfort levels.

Figure 16 - Control Knob In The

OFF Position

n TO TURN OFF n

GAS TO APPLIANCE

Shutting Off Heater

1. Turn control knob clockwise

to the OFF position.

2. Turn off all electric power to

the appliance if service is to

be performed.

SHUTTING OFF BURNER ONLY

(PILOT STAYS LIT)

Turn control knob clockwise to the PILOT/IGN position.

6. With control knob pressed in,

push down and release the

ignitor button. This will light

pilot. If needed, keep pressing

ignitor button until pilot lights.

NOTE: If pilot does not stay lit, refer to Troubleshooting, pages

14 through 16. Also contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match.

To light pilot with match, see

Manual Lighting Procedure.

Figure 17 - Pilot

n THERMOSTAT n

CONTROL

OPERATION

The thermostatic control used on these models differs from standard thermostats. Standard thermostats simply turn on and off the burner.

The thermostat used on this heater senses the room temperature. The thermostat adjusts the amount of gas flow to the burner.

n MANUAL LIGHTING n

PROCEDURE

1. Remove lower front panel (see

Figure 7 page 7).

2. Follow steps 1 through 5

under Lighting Instructions.

3. With control knob pressed in,

strike match. Hold match to

pilot until pilot lights.

4. Keep control knob pressed in

for 30 seconds after lighting

pilot. After 30 seconds, release

control knob. Follow step 8

under Lighting Instructions.

5. Replace lower front panel.

1 1

NON-THERMOSTAT MODELS n FOR YOUR SAFETY n

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A. When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area for gas.

Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

OPERATING YOUR HEATER

WHAT TO DO IF YOU SMELL GAS l Do not try to light any

appliance.

l Do not touch any electric switch, do not use any phone

in your building.

l Immediately call your gas supplier from a neighbor’s p h o n e . F o l l o w t h e g a s

supplier’s instructions.

l if you cannot reach your gas supplier, call the fire

department.

n LIGHTING n

INSTRUCTIONS

1. STOP! Read the safety

information, on the side of

heater.

2. Make sure equipment shutoff

valve is fully open.

3. Push in control knob slightly and turn clockwise to the

OFF position (see Figure 18).

4. Wait five minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas.STOP! Follow

"

B

"

in the safety information on the side of

heater. If you don’t smell gas. go to the next step.

5. Push in and turn control knob counterclockwise to PILOT position. Press in control knob

for five(5) seconds.

Note: You may be running this heater for the first time after hooking up to gas supply.

If so, you may need to press in control knob for 30 seconds.

This will allow air to bleed from

the gas system.

6. With control knob pressed in, push down and release the ignitor button. This will light pilot. if needed, keep pressing ignitor button until pilot lights.

7. Keep control knob depressed for ten(10) seconds after lighting pilot. If pilot goes out, repeat steps 5,6 and 7.

8. To select the desired heating level, partially press down the control knob slightly and rotate counterclockwise . Release the downward pressure on the knob while continuing to turn until the knob locks at the desired setting position. Do not operate between locked positions.

n TO TURN OFF n

GAS TO APPLIANCE

Shutting Off Heater

1. Turn control knob clockwise

to the OFF position.

2. Turn off all erlectric power to the appliance if service is to

be performed.

3. Turn off all erlectric power to the appliance if service is to

be performed.

Shutting Off Burner Only (pilot stays lit )

Slightly press in control, turn control knob clockwise to the

PILOT position.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by hand, don’t try to repair it , call a qualified service technician or gas supplier.

Force or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service t e c h n i c i a n t o i n s p e c t t h e appliance and to replace any part of the control system and any gas control which has been under water.

Figure 18 - Control Knob In The

OFF Position

Figure 19 - Pilot

n MANUALLIGHTINGn

PROCEDURE

1. Remove lower front panel (see

Figure 7 page 7).

2. Follow steps 1 through 5 under

Lighting Instructions, page 12.

3. With control knob pressed in,

strike match. Hold match to pilot

until pilot lights.

4. Keep control knob pressed in for

30 seconds after lighting pilot. After

30 seconds, release control knob.

Follow step 8 under Lighting

Instructions.

5. Replace lower front panel.

1 2

INSPECTING BURNER

Check pilot flame pattern and burner flame pattern often.

PILOT FLAME PATTERN

Figure 20 shows a correct pilot flame pattern. Figure 21 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching thermocouple. This will cause the thermocouple, to cool. When the thermocouple cools, the heater will shut down. If pilot flame pattern is incorrect, as shown in Figure 21.

l turn heater off (see To Turn

Off Gas to Appliance, page 12 for non-thermostat models or

page 11 for thermostat models.) l see Troubleshooting. pages 14

through 16.

Figure 20 - Correct Pilot Flame

Pattern

Figure 21 - Incorrect Pilot Flame

Pattern

BURNER FLAME PATTERN

Figure 22 shows a correct burner flame pattern. Figure 23 shows an incorrect burner flame pattern. If pilot flame pattem is incorrect, as shown in Figure 23.

l turn heater off (see To Turn Off

Gas to Appliance. page 12 for nonthermostat models or page

11 for thermostat models) l see Troubleshooting. pages 14

through 16

WARNING: If yellow tipping o c c u r s , y o u r h e a t e r c o u l d produce increased levels of c a r b o n m o n o x i d e . I f b u r n e r flame pattern shows yellow tipping, follow instructions at bottom of this page.

Notice: Do not mistake orange flames with yellow tipping. Dirt or other fine particles enter the heater and burn causing brief patches of orange flame.

Figure 22 - Correct Burner Flame

Pattern

Figure 23 - Incorrect Burner

Flame Pattern

CLEANING ODS/PILOT AND

BURNER l Use a vacuum cleaner,pressurized air or a small, soft bristled brush to clean.

CLEANING BURNER

PILOT AIR INLET HOLE

We recommend that you clean the unit every 2,500 hours of operation or every three months. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSl.

Your local computer store, hardware store or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can, you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow the unit to cool for

at least thirty minutes.

2. Inspect burner, pilot for dust

and dirt.

3. Blow air through the ports/slots

and holes in the bumer.

Also clean the pilot assembly. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 24).

With the unit off lightly blow air through the air inlet hole. You may blow through a drinking straw if comp r e s s e d a i r i s n o t a v a i l a b l e .

CLEANING AND

MAINTENANCE

WARNING: Turn off heater and let cool before servicing.

CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean.

Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

Figure 24 - Pilot Inlet Air Hole

CLEANING HEATER CABINET

Air Passageways l Use a vacuum cleaner or pressurized air to clean.

Exterior l Use a soft cloth dampened with

a mild soap and water mixture.

Wipe the cabinet to remove dust.

1 3

TROUBLESHOOTING

Note : All troubleshooting items are listed in order of operation.

WARNING: Only a qualified service person should service and repair heater.

CAUTION: Never use a wire, needle, or similar object to clean

ODS/pilot. This can damage

ODS/pilot unit.

OBSERVED PROBLEM

When ignitor button is pressed in, there is no spark at ODS/pilot.

ODS/pilot lights but flame goes out when control knob is released.

POSSIBLE CAUSE REMEDY

1. Ignitor electrode is positioned

wrong.

2. Ignitor electrode is broken.

3. Ignitor electrode is not connected

to ignitor cable.

4. Ignitor cable pinched or wet.

1. Replace ignitor.

2. Replace ignitor.

3. Reconnect ignitor cable.

5. Broken ignitor cable.

6. Bad piezo ignitor.

4. Free ignitor cable if pinched by

any metal or tubing. Keep

ignitor cable dry.

5. Replace ignitor cable.

6. Replace piezo ignitor.

1. Gas supply is turned off or equip-

ment shutoff valve is closed.

2. Control knob not fully pressed in

while pressing ignitor button.

3. Air in gas lines when installed.

4. ODS/pilot is clogged.

5. Gas regulator setting is not correct.

6. Control knob not in PILOT position.

1. Turn on gas supply or open

equipment shutoff valve.

2. Fully press in control knob

while pressing ignitor button.

3. Continue holding down control knob. Repeat igniting operation

until air is removed.

4. Clean ODS/pilot (see Cleaning and

Maintenance. Page 13 ) or

replace ODS/pilot assembly.

5. Replace gas regulator.

6.Turn control knob to PILOT position.

When ignitor button is pressed in, there is a spark at ODS/pilot but no ignition.

1. Control knob is not fully pressed

in.

2. Control knob not pressed in long

enough.

3. Equipment shutoff valve is not

fully open.

4. Thermocouple connection loose

at control valve.

5 Pilot flame is not touching thermo-

couple.This allows thermocouple

to cool, causing pilot flame to go

out. This problem could be caused

by one or both of the following:

A) Low gas pressure

B) Dirty or partially clogged

ODS/pilot

6. Thermocouple damaged.

7. Control valve damaged.

1. Press in control knob full.

2. After ODS/pilot lights, keep control

knob pressed in 30 second.

3. Fully open equipment shutoff valve.

4. Hand tighten until snug, then

tighten 1/4 turn more.

5. A) Contact local natural gas

company.

B) Clean ODS/pilot (see Cleaning

and Maintenance, Page 13)

or replace ODS/pilot asse-

mbly.

6. Replace thermocouple.

7. Contact Dealer or PRO-COM.

1 4

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

Burner(s)does not light after

ODS/pilot is lit.

POSSIBLE CAUSE

1. Burner orifice is clogged.

Delayed ignition of burner(s).

2. Burner orifice diameter is too small

3. Inlet gas pressure is too low.

1. Manifold pressure is too low.

2. Burner orifice is clogged.

Burner backfiring during combustion.

Yellow flame during burner combustion.

1. Burner orifice is clogged or

damaged.

2. Burner is damaged.

3. Gas regulator is defective.

1. Not enough air.

2. Gas regulator is defective.

REMEDY

1. Clean burner orifice (see Cleaning

and Maintenance, Page 13) or

replace burner orifice.

2. Replace burner orifice.

3. Contact local natural gas company.

1. Contact local natural gas company.

2. Clean burner (see Cleaning and

Maintenance, Page 13) or replace

burner orifice.

1. Clean burner orifice (see Clean

ing and Maintenance, Page 13) or

replace.

2. Contact Dealer or PRO-COM.

3. Replace gas regulator.

1. Check burner for dirt and debris. If

found, clean burner (see Cleaning

and Maintenance, Page 13).

2. Replace gas regulator.

Slight smoke or odor during initial operation.

Heater produces a whistling noise when burner is lit.

Heater produces a clicking/ticking noise just after burner is lit or shut off.

White powder residue forming within burner box or on adjacent walls or furniture.

1. Residues from manufacturing

processes.

1. Turning control knob to HI position

when burner is cold.

2. Air in gas line.

3. Air passageways on heater are

blocked.

4. Dirty or partially clogged burner

orifice.

1. Metal is expanding while heating or

contracting while cooling.

1. When heated the vapors from

furniture polish, wax, carpet

cleaners, etc. turn into white

powder residue.

1. Problem will stop after a few hours

of operation.

1. Turn control knob to LO position

and let warm up for a minute.

2. Operate burner until air is removed

from line. Have gas line checked

by local natural gas company.

3. Observe minimumin stallation

clearances (Figure 4, p7).

4. Clean burner (see Cleaning and

maintenance, Page13) or replace

burner orifice.

1. This is common with most

heaters. if noise is excessive,

contact qualified service person

1. Turn heater off when using

furniture polish, wax, carpet

cleaner, or similar products.

1 5

TROUBLESHOOTING

Continued

WARNING: If you smell gas l Shut off gas supply.

l Do not try to light any appliance.

l Do not touch any electrical switch; do not use any phone in your building.

l Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

l If you cannot reach your gas supplier, call the fire department.

IMPORTANT Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigaretle smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors.

OBSERVED PROBLEM

Heater produces unwanted odors.

POSSIBLE CAUSE REMEDY

1. Heater is burning vapors from

paint, hair spray, glues, etc.

(See IMPORTANT statement

above).

2 . G a s l e a k . S e e W a r n i n g

statement at top of page.

1. Ventilate room. Stop using odor

causing products while heater

is running.

2. Locate and correct all leaks(see

Checking Gas Connections,

Page 10).

Heater shuts off in use (ODS operates).

Gas odor even when control knob is in OFF position.

Gas odor exists during combustion.

Heater produces a clicking/ticking noise just after burner is lit or shut off.

Moisture/condensation noticed on windows.

1. Not enough fresh air is available.

2. Low line pressure.

3. ODS/pilot is partially clogged.

1. Open window and/or door for

ventilation.

2. Contact local natural gas

company.

3. Clean ODS/pilot (see Cleaning

Page 13).

1. Gas leak. See Warning

Statement at top of page.

2. Control valve defective.

1. Locate and correct all leaks(see

Checking Gas Connections,

Page 10).

2. Contact Dealer or PRO-COM

1. Foreign matter between control

valve and burner.

2. Gas leak. See Warning

Statement at top of page.

1. Take apart gas tubing and

remove foreign matter.

2. Locate and correct all leaks

(see Checking Gas Connections,

Page 10).

1. Metal expanding while heating

or contracting while cooling.

1. This is common with most

heaters. If noise is excessive,

contact qualified service person.

1. Not enough combustion/ventilation

air.

1. Refer to Air for Combustion and

Ventilation requirements (Page

4).

1 6

SPECIFICATIONS

MN200HBA

Btu(available)

Gas Type

Ignition

Pressure Regulator setting

Inlet Gas Pressure *(inches of water)

Maximum

Minimum

Dimensions, Inches (HxWxD)

Heater

Carton

Weight (pounds)

Heater

Shipping

10,500/20,000

Natural Only

Piezo

3" W.C.

10.5"

4"

23 1/2×19 1/4×8

26 1/2×21 3/4×9 1/4

21

25

MN200TBA

9,000/20,000

Natural Only

Piezo

3" W.C.

10.5"

4"

23 1/2×19 1/4×8

26 1/2×21 3/4×9 1/4

23

27

MN300HBA

15,000/30,000

Natural Only

Piezo

3" W.C.

10.5"

4"

23 1/2×26 5/8×8

26 1/2×28 1/2×9 1/4

26

31

MN300TBA

14,000/30,000

Natural Only

Piezo

3" W.C.

Note: Dimensions listed are outer most points on the heater (includes control knobs and grill).

* For purposes of input adjustment.

10.5"

4"

23 1/2×26 5/8×8

26 1/2×28 1/2×9 1/4

28

33

REPLACEMENT PARTS

Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealer from whom you purchased this product.

If they are unable to supply original replacement part(s), call the number on the front of manual When contacting your dealer or PRO-COM, have ready.

l your name l your address l model and serial numbers of

your heater l how heater was malfunctioning l type of gas used (propane/LP or

natural gas) l purchase date l warranty card

Usually, we will ask you to return the defective part to the factory.

PARTS NOT UNDER

WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s), call PRO-COM’S phone number (877)886-5989.

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. If so, contact

PRO-COM’S phone number (877)

886-5989.

ACCESSORIES

Purchase these heater accessories from your local dealer. If they can not supply these accessories, contact PRO-COM for information.

You can also write to the address listed on the front of this manual.

EQUIPMENT SHUTOFF VALVE

For all models. Equipment shutoff valve with 1/8

"

NPT tap.

FAN PF06-YJLF-B

Optional FAN Kit

The optional fan kit, part PF06-YJLF-B fits all models noted in this manual.

The fan has 3 settings ON/OFF/Auto.

The thermostatically controlled PF06-

YJLF-B improves heater efficiency and includes installation and operating instructions.

FLOOR MOUNTING STAND

For locating heater on the floor, away from a wall. Complete installation instructions provided with floor mounting stand.

1 7

ILLUSTRATED

PARTS BREAKDOWN

THERMOSTAT MODELS

MN200TBA MN300TBA

1 8

ODS/Pilot Assembly

PARTS LIST

MN200TBA

MN3OOTBA

This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page

17 of this manual.

MN200TBA

PART NO.

MB10055

MB09052

MB11054

ML086-02

ML087-02

ML088-02

ML069-02

SIT545-200

845-4.8x60Z

ML111-01

ML083-03

ML073-01

NRV81FI-3

96-4Z

ML079-01

MB40006

MB40022

MB40023

NBB20-000B1

ML101-01

ML091-04

ML103-01

ML104-01

ND1103x800x9

ND0803-8

ND0807

ML105-01

6170-5Z

MB29002

ML157-02

ML060-01

KEY

NO.

1

24_2

25

26

27

28

29

18

19

20

21

22

23

24

24_1

14

15

16

17

10

11

12

13

8

9

6

7

4

5

2

3

MN300TBA

PART NO.

MB10052

MB09051

MB11052

ML086-01

ML087-01

ML088-01

ML069-02

SIT545-250

845-4.8x60Z

ML111-01

ML083-03

ML073-01

NRV81FI-3

ML038-01

ML079-01

MB40006

MB40022

MB40023

NBB30-000B1

ML101-01

ML091-02

ML103-01

ML104-01

ND1103x800x9

ND0803-8

ND0807

ML105-01

6170-5Z

MB29001

ML157-01

ML060-01

DESCRIPTION

Cabinet Assembly

Lower Front Assembly

Reflector Unit

Glass

Uper Glass retainer

Lower Glass Retainer

Self Tapping Screw

Thermostat Valve Assembly

Screws

Thermosstat Valve Base Assembly

Ignitor Assembly

Ignitor Line

Pressure Regulator

Washer

Self Locking Screw

Main Inlet Tube Assembly

ODS Line Assembly

Burner inlet Tube Assembly

Burner

Burner Connector

Injector

Left Burner Support Bracket

Right Burner Support Bracket

ODS

Thermocouple

Ignitor Electrode

ODS Upper Deflector

NUT

Grill Guard

Middle Panel

Mounting Bracket

MB28001

ML070-21

ML071-01

ML072-01

ML065-01

MB28001

ML070-23

ML071-01

ML072-01

ML065-01

Hardware Kit

CSA/AGA Label

Gas Instruction Decal

Inside Warning Label

Thermostat Sensing Bulb Clip

QTY

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

2

1

1

1

1

1

16

1

2

1

2

1

1

1

1

1

1

2

1 9

ILLUSTRATED

PARTS BREAKDOWN

NON-THERMOSTAT MODELS

MN200HBA MN300HBA

2 0

ODS/Pllot Assembly

PARTS LIST

MN200HBA

MN300HBA

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page17 of this manual.

KEY

NO.

1

26

27

28

28-1

28-2

29

30

31

32

33

22

23

24

25

18

19

20

21

14

15

16

17

10

11

12

13

8

9

6

7

4

5

2

3

MN200HBA

PART NO.

MB11056

MB09052

MB11054

ML086-02

ML087-02

ML157-02

ML088-01

ML069-02

NV2020-14

ML073-01

MB16002

ML029-01

NRV81FI-3

96-4Z

ML079-01

MB40016

MB40018

MB40019

MB40020

MB40021

ML096-01

MB40017

NBB20-000B1

ML101-01

ML091-03

ML103-01

ML104-01

ND1103x800x9

ND0803-8

ND0807

ML105-01

6170-5Z

MB29002

ML083-03

ML060-01

MN300HBA

PART NO.

MB10053

MB09051

MB11052

ML086-01

ML087-01

ML157-01

ML088-01

ML069-02

NV2020-14

ML073-01

MB16002

ML029-01

NRV81FI-3

96-4Z

ML079-01

MB40016

MB40018

MB40019

MB40020

MB40021

ML096-01

MB40017

NBB30-000B1

ML101-01

ML091-01

ML103-01

ML104-01

ND1103x800x9

ND0803-8

ND0807

ML105-01

6170-5Z

MB29001

ML083-03

ML060-01

DESCRIPTION

Cabinet Assembly

Lower Front Panel Assembly

Reflector Unit

Glass

Uper glass retainer

Middle Panel

Lower Glass Retainer

Self Tapping Screw

Control valve

Ignitor Line

Control Knob Assembly

Control Valve Fixed Nut

Pressure Regulator

Washer

Self Locking Screw

Main Inlet Tube Assembly

ODS Line Assembly

Lower Gas Outline Tube Assembly

Medium Gas Outline Tube Assembly

High Gas Outline Tube Assembly

4-Way Connector

Burner Inlet Tube Assembly

Burner

Burner Connector

Injector

Left Burner Support Bracket

Right Burner Support Bracket

ODS/Pilot Assembly

Thermocouple

Ignitor Electrode

ODS Upper Deflector

NUT

Grill Guard lgnitor Assembly

Mounting Bracket

MB28001

ML070-15

ML071-01

ML072-01

MB28001

ML070-17

ML071-01

ML072-01

Hardware Kit

CSA/AGA Label

Gas Instruction Decal

Inside Warning Label

QTY

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

2

1

1

1

1

1

1

16

1

1

1

1

1

1

1

1

1

2 1