Quick Reference Guide

Colorado™ Zoom Tour WW QRG

About This

Guide

Disclaimer

The Colorado™ Zoom Tour WW Quick Reference Guide (QRG) only contains the product’s connection and mounting information, as well as the menu options and the DMX values.

• This Quick Reference Guide does not replace the product’s User

Manual, available at www.chauvetpro.com

.

• You must read ALL the disclaimers and safety notes in this document, as well as those in the product’s User Manual before installing, operating, or maintaining this product.

Notes

Safety

• DO NOT open this product unless instructed. It contains no user-serviceable parts.

•

DO NOT aim this product toward the Sun. The lenses could concentrate the solar energy and cause internal overheating.

•

•

DO NOT look at the light source when this product is on.

DO NOT touch the product when it is operating because it may be very hot.

•

•

•

DO NOT install or operate this product where there is less than 50 cm to the nearest surface to allow adequate ventilation around it.

• the risk of fire.

•

DO NOT mount this product overhead without using a safety cable.

• This product is for indoor use only! To prevent risk of fire or shock, do not expose this product to rain or moisture.

•

DO NOT leave any flammable material within 50 cm from this product while operating or connected to the power outlet to minimize

DO NOT operate this product if you see damage on the housing, lenses, or cables. Have the damaged parts replaced by an authorized technician immediately.

DO NOT connect this product to a dimmer or rheostat.

ONLY connect this product to a grounded and protected circuit.

What Is

• One Colorado™ Zoom Tour WW

Included

• One Neutrik® powerCON® to

Edison Plug Input Power Cord

• One Gel Frame

• One Accessory Holder

• One Warranty Card

• One Quick Reference Guide

• One Safety Cable

Page 2 of 8

Colorado™ Zoom Tour WW QRG

Features

• 1, 4, or 5-channel DMX control

• Operating modes:

1-channel: Dimmer

4-channel: Dimmer, macro, zoom, zoom reset

5-channel: WW, CW, dimmer, zoom, zoom reset

• Color temperature control with or without DMX control

• 8~27.5° zoom control with or without DMX control

• Five distinct dimming curves

• Cool and warm white LEDs

• Electronic dimmer

• Electronic power supply

• Neutrik® powerCON® connectors

• 3- and 5-pin DMX input and output connectors

• Additional power output: max 7 units @ 120 V

• LED display with password protection

• Gel frame holder (4 mm max. thickness)

• Double-bracketed yoke doubles as floor stand

• Color calibration

• Flicker-free operation for HD Video

Page 3 of 8

Colorado™ Zoom Tour WW QRG

Product

Description

The Colorado™ Zoom Tour WW is a Warm White LED wash light. A single module houses the internal power supply, the main control, the control panel, the LED drivers, the LED boards, and motorized moving lenses, as well as the power and signal connectors. The Colorado™

Zoom Tour WW features a variable zoom enabling you to change the beam angle via DMX or control panel. One mounting bracket doubles as a floor mount or hanging support.

DMX In

Double- bracketed

Yoke

Bottom View

Front View

Power In/Out

DMX Out

Page 4 of 8

Colorado™ Zoom Tour WW QRG

AC Power

Power

Linking

DMX

Linking

DMX

Connection

Master/Slave

Connection

Start Address

This product has an auto-ranging power supply that works with an input voltage range of 100~240 VAC, 50/60 Hz.

You can link up to 7 Colorado™ Zoom Tour WW units at 120

VAC, 12 at 208 VAC, or 14 at 230 VAC.

The Colorado™ Zoom Tour WW can work with a DMX controller when linked using a regular DMX serial connection.

If you are not familiar with the DMX standard, please download the

DMX Primer document from www.chauvetpro.com

.

The Colorado™ Zoom Tour WW uses a regular DMX data connection for its 3 DMX personalities, UNO, STD.P, and STD.W.

Download the Colorado™ Zoom Tour WW User Manual. Refer to the Setup chapter to learn how to connect this product for DMX operation. To learn how to configure this product for DMX operation, refer to the Operation chapter.

The Colorado™ Zoom Tour WW uses the DMX data connection for its Master/Slave mode.

Download the Colorado™ Zoom Tour WW User Manual. Refer to the Setup chapter to learn how to connect this product for

Master/Slave operation. To learn how to configure this product for

Master/Slave operation, refer to the Operation chapter.

To ensure full access to all channels in each DMX mode, the highest recommended DMX addresses are as follows:

Mode Address

UNO

STD.P

512

509

STD.W 508

Page 5 of 8

Colorado™ Zoom Tour WW QRG

Mounting

Before mounting this product, read the Safety Notes in this guide and in the product’s User Manual. Then, follow the mounting procedure

Product

Mounting

Diagram indicated in the Setup chapter of the User Manual.

Overhead Mounting

Floor Mounting

Page 6 of 8

Colorado™ Zoom Tour WW QRG

Programming

For details on how to program this product, please refer to the product’s User Manual.

Control Panel

Description

<MENU> Exits from the current menu or function

Enables the currently displayed menu or sets the

<ENTER> currently selected value into the selected function

Button Function

<UP>

Navigates upwards through the menu list and increases the numeric value when in a function

<DOWN>

Navigates downwards through the menu list and decreases the numeric value when in a function

Password

After being prompted to enter the password, press:

<UP>, <DOWN>, <UP>, <DOWN>, <ENTER>.

Menu Options

Main Level

STAT

DMX

RUN

PERS

SET

CALIB1

KEY

ZOOM

Programming Levels Description

W.

C. 000~255

Combines Warm White and Cool White to generate a custom color (0~100%)

Z.

REST

DIM

DERR

CALE

ZOOM

001~512

DMX

SLAV

STD.W

Sets 8~27.5° zoom

Sets the DMX starting address

Receives signals from DMX controller

Receives signals from Master unit

5-channel: WW, CW, D, Z, ZR

STD.P

UNO

4-channel: D, Macro, Z, ZR

1 channel: D

Enter password Defaults product

OFF

DIM1~4

BLAK

No dimmer

Dimmer curve

SAVE

All LEDs turn off when DMX signal is lost

All LEDs stay on the last command used when the DMX signal is lost

YES

NO

BASE

POS.1

POS.2

Allows calibration setting to be changed

Locks out changes to calibration

Sets default zoom position (full movement)

Sets position 1 setting for zoom limit

Sets position 2 setting for zoom limit

WH 01~05

W

C.

ON/OFF

POS.1

POS.2

000~255 White calibration

000~255

000~255

Turns the password on or off

Sets the value limit of the zoom preset

Page 7 of 8

Colorado™ Zoom Tour WW QRG

DMX Values

UNO

Channel Function

1

Value

Master Dimmer 000  255 0~100%

Percent/Setting

STD.P

Channel Function

1

2

3

Value Percent/Setting

Master Dimmer 000  255 0~100%

Macro

Zoom

000  010

011  050

051  080

081  110

111  140

141  255

No Function

White 1

White 2

White 3

White 4

White 5

000  255 0~100%

4 Zoom Reset

000  200

201  220

221  255

No Function

Zoom Reset

No Function

STD.W

Channel Function

1

Value

Master Dimmer 000  255 0~100%

Percent/Setting

2 Warm White 000  255 0~100%

3 Cool White 000  255 0~100%

4 Zoom 000  255 0~100%

5 Zoom Reset

000  200

201

 220

221  255

No Function

Zoom Reset

No Function

Contact Us

World Headquarters

CHAUVET®

General Information

Address: 5200 NW 108th Avenue

Sunrise, FL 33351

Voice:

Fax:

Toll free:

Technical Support

(954) 929-1115

(954) 929-5560

(800) 762-1084

Voice:

Fax:

(954) 929-1115 (Press 4)

(954) 756-8015

Email: [email protected]

World Wide Web www.chauvetpro.com

Colorado™ Zoom Tour WW QRG – Rev. 09

© Copyright 2012 CHAUVET®

All rights reserved.

Printed in the P. R. C.

United Kingdom and Ireland

CHAUVET® Europe Ltd.

General Information

Address: Unit 1C

Brookhill Road Industrial Estate

Voice:

Fax:

Pinxton, Nottingham, UK

NG16 6NT

+44 (0)1773 511115

+44 (0)1773 511110

Technical Support

Email: [email protected]

World Wide Web www.chauvetlighting.co.uk

Page 8 of 8