advertisement
SCH-a570 Series
P O R T A B L E D u a l - M o d e
M O B I L E P H O N E
User Guide
Please read this manual before operating your phone, and keep it for future reference.
YJ16.05_CB_102705_F5
Intellectual Property
All Intellectual Property, as defined below, owned by or which is otherwise the property of Samsung or its respective suppliers relating to the SAMSUNG Phone, including but not limited to, accessories, parts, or software relating there to (the “Phone
System”), is proprietary to Samsung and protected under federal laws, state laws, and international treaty provisions. Intellectual
Property includes, but is not limited to, inventions (patentable or unpatentable), patents, trade secrets, copyrights, software, computer programs, and related documentation and other works of authorship. You may not infringe or otherwise violate the rights secured by the Intellectual Property. Moreover, you agree that you will not (and will not attempt to) modify, prepare derivative works of, reverse engineer, decompile, disassemble, or otherwise attempt to create source code from the software. No title to or ownership in the Intellectual Property is transferred to you. All applicable rights of the Intellectual Property shall remain with SAMSUNG and its suppliers.
Samsung Telecommunications America (STA),
Inc.
Headquarters:
1301 E. Lookout Drive
Richardson, TX 75082
Tel: 972.761.7000
Customer Care Center:
1000 Klein Street
Plano, TX 75074
Toll Free Tel: 1.888.987.HELP (4357)
Internet Address: http://www.samsungusa.com
©2005 Samsung Telecommunications America, Inc. is a registered trademark of Samsung Electronics America, Inc. and its related entities.
Licensed by Qualcomm Incorporated under one or more of the following patents: U.S. Patent No. 4, 901, 307; 5, 056, 109; 5, 099, 204;
5, 101, 501; 5, 103, 459; 5, 107, 225; 5, 109, 390.
Printed in South Korea
GH68-08021A
Openwave® is a registered Trademark of Openwave, Inc.
RSA® is a registered Trademark RSA Security, Inc.
Disclaimer of Warranties; Exclusion of Liability
EXCEPT AS SET FORTH IN THE EXPRESS WARRANTY
CONTAINED ON THE WARRANTY PAGE ENCLOSED WITH
THE PRODUCT, THE PURCHASER TAKES THE PRODUCT “AS
IS”, AND SAMSUNG MAKES NO EXPRESS OR IMPLIED
WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT
TO THE PRODUCT, INCLUDING BUT NOT LIMITED TO THE
MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR
ANY PARTICULAR PURPOSE OR USE; THE DESIGN,
CONDITION OR QUALITY OF THE PRODUCT; THE
PERFORMANCE OF THE PRODUCT; THE WORKMANSHIP
OF THE PRODUCT OR THE COMPONENTS CONTAINED
THEREIN; OR COMPLIANCE OF THE PRODUCT WITH THE
REQUIREMENTS OF ANY LAW, RULE, SPECIFICATION OR
CONTRACT PERTAINING THERETO. NOTHING
CONTAINED IN THE INSTRUCTION MANUAL SHALL BE
CONSTRUED TO CREATE AN EXPRESS OR IMPLIED
WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT
TO THE PRODUCT. IN ADDITION, SAMSUNG SHALL NOT BE
LIABLE FOR ANY DAMAGES OF ANY KIND RESULTING
FROM THE PURCHASE OR USE OF THE PRODUCT OR
ARISING FROM THE BREACH OF THE EXPRESS WARRANTY,
INCLUDING INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, OR LOSS OF ANTICIPATED PROFITS OR
BENEFITS.
Table of Contents
Section 1: Getting Started ................................. 9
Activating Your Phone .................................................... 10
Charging the Battery ...................................................... 12
Setting Up Your Voice Mail ............................................. 13
Understanding this User Manual ..................................... 14
Section 2: Understanding Your Phone ............ 15
Features of Your Phone .................................................. 16
Closed View of Your Phone ............................................. 16
Open View of Your Phone ............................................... 18
Understanding the Display Screen .................................. 20
Section 3: Call Functions ................................. 23
Making a Call—Number Entry Dialing ............................ 24
Making a Call—Speed Dialing ........................................ 25
Making a Call—Voice Dialing ......................................... 26
Answering a Call ............................................................ 29
Ignoring a Call ................................................................ 30
Adjusting the Call Volume ............................................... 30
Calls Log ........................................................................ 31
Phone Modes ................................................................. 35
Roaming ........................................................................ 40
Section 4: Menu Navigation ............................ 41
Menu Navigation ............................................................ 42
In Use Menu Outline ....................................................... 44
Menus and sub-menus .................................................. 45
Section 5: Entering Text .................................. 53
Text Entry Modes ........................................................... 54
Entering Upper and Lower Case Letters .......................... 54
Entering Symbols ........................................................... 55
Entering Numbers .......................................................... 56
Table of Contents 5
6
Using T9 Mode ...............................................................56
Changing the Text Entry Mode ........................................57
Section 6: Understanding Your Contacts ........ 59
Your Contacts List ..........................................................60
Adding a New Contacts Entry ..........................................61
Finding a Contacts Entry .................................................66
Editing an Existing Contact Entry ....................................71
Renaming a Contacts Group ...........................................75
Deleting a Contact Entry .................................................75
Finding My Phone Number .............................................76
Memory ..........................................................................77
Section 7: @metro ........................................... 79
@metro Catalog .............................................................80
Settings ..........................................................................81
Help ...............................................................................82
Section 8: MyMetro .......................................... 85
Monthly Bill ....................................................................86
MetroConnect .................................................................86
MetroPCS Card ...............................................................87
Section 9: Messaging ...................................... 89
Creating and Sending New Messages .............................90
Message Send Options ...................................................91
Retrieving New Messages ..............................................92
Voice Mail ......................................................................93
Message Folders ............................................................94
Message Settings ...........................................................98
Deleting Messages .......................................................100
Section 10: Sounds ........................................ 103
Volume/Vibrate .............................................................104
Ringer Type ..................................................................104
Key Beep ......................................................................105
Alerts ........................................................................... 106
Power On/Off ............................................................... 107
Roam Ringer ................................................................ 108
Whisper Mode .............................................................. 108
Section 11: Tools ........................................... 109
Tools ............................................................................ 110
Voice ............................................................................ 112
Today ........................................................................... 122
Calendar ...................................................................... 124
To-Do List .................................................................... 125
Alarm Clock ................................................................. 127
Memo Pad ................................................................... 129
World Time .................................................................. 130
Calculator .................................................................... 131
Count Down ................................................................. 132
Section 12: Mobile Web ................................. 135
Mobile Web .................................................................. 136
Launching Mobile Web ................................................. 136
Using Mobile Web ........................................................ 137
Using Links .................................................................. 138
How Mobile Web Keys Work ......................................... 138
Section 13: Set Up ......................................... 141
Location Setting ........................................................... 142
Network Selection ........................................................ 142
Security Settings .......................................................... 143
Display Settings ........................................................... 148
Ringer Settings ............................................................ 154
Call Options .................................................................. 154
Shortcut ....................................................................... 159
Language ..................................................................... 160
Clock Set ..................................................................... 160
Version ......................................................................... 161
Table of Contents 7
8
Section 14: Health and Safety Information ... 163
Health and Safety Information .......................................164
Consumer Information on Wireless Phones ...................166
Road Safety ..................................................................176
Operating Environment .................................................178
Using Your Phone Near Other Electronic Devices ..........179
Potentially Explosive Environments ...............................180
Emergency Calls ...........................................................181
FCC Notice and Cautions ..............................................183
Other Important Safety Information ...............................184
Product Performance ....................................................184
Availability of Various Features/Ring Tones ...................186
Battery Standby and Talk Time .....................................186
Battery Precautions ......................................................186
Care and Maintenance ..................................................188
Section 15: Warranty Information ................. 191
Standard Limited Warranty ...........................................192
Index ............................................................... 199
Section 1: Getting Started
Topics Covered
• Activating your phone
• Charging the Battery
• Setting Up Your Voice Mail
• Understanding this User Manual
This section explains how to start using your phone by activating your service, setting up your voice mail, contacting customer support, or getting an understanding of how this manual is put together.
Section 1: Getting Started 9
Activating Your Phone
Contact your Wireless Carrier and follow their instructions for obtaining service, if necessary. We suggest that you read this guide to fully understand the services your phone supports.
Install the Battery
Note: Your phone comes packaged with a partially charged rechargeable standard Li-Ion battery and travel adapter.
Important: You can use your phone while the battery is charging, but you must fully charge the battery the first time you use your phone, otherwise you could damage the battery.
1. Insert the bottom end of the battery first, matching the gold contacts on the inside of the battery to those on the phone.
2. Press the top end of the battery down into the phone until you hear it snap into place.
10
Activating Your Phone
Remove the Battery
1. Press and hold the key to turn off the phone (if on).
2. Slide the battery release latch (1) toward the top end of the phone and hold.
1
2
3. Lift the battery (2) up and away from the phone, top end first.
Turn Your Phone On
1. Fully extend the antenna for the clearest reception, then open the folder on your phone.
2. Press and hold the key for two or more seconds.
Note: As with any other radio-transmitting device, do not touch the antenna while using your phone as this can affect call quality and can cause the phone to operate at a higher power level than is necessary.
3. “MetroPCS” momentarily appears in the display and your phone begins searching for a network signal.
4. Once the phone finds a signal, the time, date and day appear in the bottom of the display.
5. You’re now ready to place and receive calls.
Note: If you are outside of your carrier’s coverage or roaming area, the No
Service icon ( ) appears at the top of the phone’s display. If you cannot place or receive calls, try later when service is available.
Section 1: Getting Started 11
Turn Your Phone Off
â– Press and hold the key for two or more seconds. Your phone powers off.
Note: If your phone is on and you press for less than one second, the phone will not power off. This prevents your phone from being turned off accidentally.
Charging the Battery
Your phone is powered by a rechargeable standard Li-
Ion battery. Only use Samsung-approved charging devices and batteries. Samsung accessories are designed to maximize battery life. Using other accessories may invalidate your warranty and may cause damage.
Use the Travel Adapter
The travel adapter included with your phone is a convenient, light-weight charger that rapidly charges your phone from any 120/220 VAC outlet.
1. Plug the large end of the Travel Adapter into a standard
120 VAC or 220 VAC wall outlet.
2. Insert the smaller end of the
Travel Adapter into the charger/accessory connector at the bottom end of your phone.
12
Setting Up Your Voice Mail
Low battery indicator
The battery indicator ( ) in the upper-right corner of the display indicates power level. Monitor the battery strength and ensure your battery is adequately charged.
• Four bars ( ) indicate a full charge.
• An empty battery icon ( ) indicates a near empty battery.
• A blinking empty battery icon ( ) and a tone sounding indicate you have two to three minutes before the battery is too low to operate the phone.
If you continue to use your phone without charging its battery, the phone shuts down.
Setting Up Your Voice Mail
1. In standby mode, press and hold the key. Voice
Mail answers and begins playing your account greeting message.
2. Press the key to interrupt the greeting.
3. Follow the prompts in the new user tutorial to setup you mailbox.
Section 1: Getting Started 13
Understanding this User Manual
The chapters of this guide generally follow the same order as the menus and sub-menus in your phone.
Also included is important safety information that you should know before using your phone. Most of this information is near the back of the guide, beginning on
If you still have questions, we’ll be happy to answer them. Just call our Samsung Customer Care Center tollfree at 1.888.987.HELP (4357).
14
Section 2: Understanding Your Phone
Topics Covered
• Features of Your Phone
• Closed View of Your Phone
• Open View of Your Phone
• Understanding the Display Screen
This section outlines some key features of your phone. This section also explains the screen and the icons that are displayed when the phone is in use.
Section 2: Understanding Your Phone 15
Features of Your Phone
• 128 X 160 pixel Liquid Crystal Display
• High speed data (CDMA 2000 1X Technology)
• Global Positioning Technology (GPS)
• PIM functions (Scheduler, To Do List, and more)
• Short Message Service (SMS)
• Voice Dial
• 32-Note Polyphonic Ringtones
Closed View of Your Phone
16
Closed View of Your Phone
Command Keys and Features
1. Headset Connector—Used for handsfree,
Teletypewriter (TTY), and Telecommunication Device for the Deaf (TDD) equipment.
2. Volume Key—Lets you adjust the ringer volume in standby mode (with the folder open) or adjust the voice volume during a call. To mute the ringer during an incoming call, press the volume key up or down.
3. Speaker—The speaker, on the front of the folder, plays sounds such as ring tones and alerts.
4. External LCD—Indicates when you have an incoming call or a message.
5. Service LED—The Service LED on the top of the phone has the following functions.
䢇 Lights red while charging. Green when charging is complete.
䢇 Flashes to indicate an incoming call or message.
䢇 Lights momentarily when you power up the phone and flashes red when the phone is in need of a charge
6. Antenna—Used to exchange signals with the network.
Extendable for improved reception.
Section 2: Understanding Your Phone 17
Open View of Your Phone
Command Keys and Features
7. Display Icons—This screen displays all the information needed to operate your phone.
8. Mobile Web—In Idle mode, launches Mobile Web.
9. Left Soft Key—Performs the functions indicated by the screen text on the bottom of the display.
10. SEND Key—This key is used to initiate your calls.
18
Open View of Your Phone
11. OK Key—Pressing when navigating through a menu accepts the highlighted choice in the menu.
12. Voice Mail Key—Press and hold to automatically dial your voice mail.
13. Alphanumeric Key Pad—Use these keys to enter numbers, letters, and characters.
14. Hot Key—Lets you enter and exit silent mode.
15. Charger/PC Data Link Cable Jack—The Charger/PC
Data Link Cable Jack is used to plug in the charging accessories and connect any available accessory cable
16. Microphone—The microphone used during phone calls and voice memo recordings.
17. CLR (clear) Key—Deletes characters from the display when you are in text entry mode. When in a menu, press to return to the previous menu.
18. Messages—In Idle mode, launches the Messages menu.
19. END/Power/Exit Menu Key—Ends a call. Press and hold this key for a few seconds to turn your phone On or
Off. When you receive an incoming call, press to mute the ringer and send the call to voice mail.
20. Right Soft Key—Performs the functions indicated by the screen text on the bottom of the display.
21. @metro—In Idle mode, launches @metro.
22. User Defined Shortcut—Lets you customize key.
23. Earpiece—Used to listen.
Section 2: Understanding Your Phone 19
Understanding the Display Screen
The top line of your phone’s display contains icons that indicate network status, battery power, signal strength, connection type, and more. The following list contains icons that may appear in your display.
Display screen icons
Signal strength—Always appears when your phone is on and indicates the current signal strength. More lines indicate higher signal strength.
Service indicator—Indicates a call in progress. When dialing a number, this icon flashes until the call connects.
No service indicator—Indicates your phone cannot find a signal because you’re outside a service area. You cannot make or receive calls. Wait for a signal or move into an open area to try and find a signal. The no service indicator always appears when you turn on your phone and disappears once service is located.
Roam—Extended roaming indicator. Roaming occurs when you use your phone outside your home area. While roaming, a wireless provider's system other than
MetroPCS handles your call, so the service rate for the call may be higher than those made within your home area. Please refer to information from your Wireless
Provider on roaming rates.
New Message—Indicates that you’ve received a new text, page, or web alert message. You’re also notified by a visual and audible alert.
20
Understanding the Display Screen
Voice Mail—Indicates that you’ve received a new voice mail.
1X Protocol—Indicates your phone is using the 1X protocol.
IS95-2G Protocol—Indicates your phone is using the
IS95-2G protocol. This protocol is not capable of high speed data.
Battery strength—Indicates the battery charge level.
The more black bars, the greater the charge. When the battery becomes very low, a flashing empty battery icon displays and the phone sounds an audible alert, which indicates your phone is about to shut down.
Alarm clock—The alarm clock is set.
GPS (911 only)—This icon represents Global Positioning
Service (GPS) for 911.
GPS—Indicates GPS is on for location.
Vibrate plus Ring—Your phone is in vibrate plus ring mode. When you receive a call, the phone vibrates and rings.
Ring—Your phone is in ring/beep mode. When you receive a call, the phone rings/beeps once.
Ringer Silent—The ringer has been set to Ringer Off using the volume key on the side of the phone.
Section 2: Understanding Your Phone 21
22
Silent mode—Indicates your phone is in silent mode.
Ringer is silenced for all alerts, incoming calls, and incoming messages. The phone alerts you of incoming calls, alerts, and messages by vibration and a flashing
Service LED.
Vibrate mode—Your phone is in vibrate mode. When you receive a call, the phone vibrates instead of ringing.
Section 3: Call Functions
Topics Covered
• Making a Call—Number Entry Dialing
• Making a Call—Speed Dialing
• Making a Call—Voice Dialing
• Answering a Call
• Ignoring a Call
• Adjusting the Call Volume
• Calls Log
• Phone Modes
• Roaming
This section explains how to make or answer a call.
This section also includes the features and functionality associated with making or answering a call.
Section 3: Call Functions 23
Making a Call—Number Entry Dialing
1. With the phone on, enter the number you wish to call using the keypad.
2. Press the key to place the call.
Manual Pause Calling
When you call automated systems (like banking services), you are often required to enter a password or account number. Instead of manually entering the numbers each time, you can store the numbers in your
Contacts along with special characters called pauses.
• P pause—A hard pause stops the calling sequence until further input from you.
• T pause—A two-second pause stops the calling sequence for two seconds and then automatically sends the remaining digits.
To manually call a number with pause(s) without storing it to your Contacts:
1. Enter the number you wish to call.
2. Press the Option (left) soft key ( ). A pop-up menu appears in the display containing the following options:
䢇 P pause—a hard pause (awaits input from you).
䢇 T pause—a two-second pause.
3. Use the navigation keys to highlight the desired pause option.
4. Press to enter the highlighted pause into your number sequence.
5. Press to call the number.
24
Making a Call—Speed Dialing
Making a Call—Speed Dialing
You can store phone numbers and contact names in your phone’s Contacts list. Speed Dialing lets you quickly and easily dial any contact in your Contacts list by using that contact’s location number in the list. You can assign and change location (speed dial) numbers
for your contacts. (See “Assigning Speed Dial
Numbers” on page 72 for more information.)
One-Touch Dialing
Memory locations 001 through 009 are special One-
Touch dialing locations. You can call the phone numbers stored in your phone’s Contacts list from 001 through 009 by pressing and holding a single key.
Example: For location number 001, press and hold the key until the name and number appear in the display and the number is dialed.
Two-Touch Dialing
Memory locations 010 through 099 are special Two-
Touch dialing locations.
Example: For location number 013, briefly press the key, then press and hold the key until the name and number appear in the display and the number is dialed.
Section 3: Call Functions 25
Three-Touch Dialing
Memory locations 100 through 500 are special Three-
Touch dialing locations.
Example: For location number 113, briefly press the key, briefly press the key again, then press and hold the key until the name and number appear in the display and the number is dialed.
Pause Dialing From a Contacts Entry
• If you speed dial a contact that contains (two-second) T pause(s) simply wait for the pauses to pass and the dialing to complete.
• If you speed dial a contact that contains (hard) P pause(s), wait for the appropriate prompt(s) from the number you are calling
(credit card number, bank account number, and so on) and enter the appropriate response(s).
Making a Call—Voice Dialing
Your SCH-a570 mobile phone includes state-of-the-art voice recognition software that lets you dial numbers using your voice.
Using Voice Dial
Use the Voice Dial command to dial any number stored in your Contacts list by saying the name of the contact
(Name Dialing). You can also use Voice Dial to dial any valid telephone number, even numbers not stored in your contact list, by speaking the individual digits in the number (Digit Dialing).
26
Making a Call—Voice Dialing
Voice Dialing Tips:
• Wait for the beep before speaking.
• Speak clearly at a normal volume, as if you were talking to someone on the phone.
• When saying a name, say the first name then the last name.
Dialing a Name
To dial a name, do the following:
1. In standby mode, press and hold the key.
“Say a Command” appears in the display and is pronounced through the earpiece.
2. Say, “Voice Dial”.
You are prompted to “Say the name or number”.
3. Speak clearly and say the name of a person in your
Contacts list, first name followed by last name.
If the name is recognized, Voice Dial repeats the name and dials the number.
If Voice Dial is not sure which name you said, it displays a choice list of up to three names and prompts you with
“Did you say?” followed by the first name on the list.
4. Say “Yes” to confirm the name or “No” to hear the next name, or use the keypad to select the correct name
from the list. (See “Choice Lists Settings” on page 118,
for more information.)
䢇 Press the Repeat (right) soft key ( ) to say the name again.
䢇 Press the Settings (left) soft key ( ) and press the Cancel right soft key ( ) to exit Voice Dial without dialing.
Section 3: Call Functions 27
If the recognized name has multiple numbers stored for it
(that is, Mobile, Office, Home, and so on), Voice Dial displays the possible choices and prompts you with
“Which number?”
5. Say one of the following number types:
䢇 “Mobile”
䢇 “Office”
䢇 “Home”
䢇 “Pager”
䢇 “Fax”
Voice Dial dials the specified number.
Dialing a Number
To dial a number using Voice Dial, do the following:
1. In standby mode, press and hold the key.
“Say a Command” appears in the display and is pronounced through the speaker.
2. Say “Voice Dial”.
VoiceSignal prompts you to “Say the name or number.”
3. Speak clearly and say the telephone number of the person you want to call. For example, say “7 8 1 9 7 0 5
2 0 0."
If it recognizes the number, Voice Dial repeats it and dials the number. If Voice Dial is not sure it has recognized the number, it displays a choice list of up to three numbers and prompts you with “Did you say?” followed by the first number on the list.
28
Answering a Call
4. Say “Yes” to confirm the number or “No” to hear the next one, or use the keypad to select the correct number
from the list. (See “Choice Lists Settings” on page 118,
for more information.)
䢇 Press the Repeat (right) soft key ( ) to say the number again.
䢇 Press the Settings (left) soft key ( ) and press the Cancel right soft key ( ) to exit Voice Dial without dialing.
Pause Dialing From a Contacts Entry
• If you voice dial a contact that contains (two-second) T pause(s) simply wait for the pauses to pass and the dialing to complete.
• If you voice dial a contact that contains (hard) P pause(s), wait for the appropriate prompt(s) from the number you are calling
(credit card number, bank account number, and so on) and enter the appropriate response(s).
Answering a Call
Your phone notifies you of a call in the following ways:
• A ring tone sounds and/or your phone vibrates
(Your phone provides: nine ring volume settings including 1- beep , Vibrate , Ringer Off , or Vibrate+Ring, and/or different ring types to distinguish callers.)
• The Activity LED flashes.
• A phone number (unless blocked by the caller) and a name appear in the display (If the caller’s number and name are stored in your Contacts list).
• If the caller can’t be identified, Call from unavailable#, Call
from restricted number, or no number appears in the display.
Section 3: Call Functions 29
Your phone continues to notify you of the call until one of the following events occurs:
• You answer the call.
• You ignore the call.
• The calling party ends the call.
• The call is sent to voice mail.
Answering an Incoming Call
â– Press the key. The ring tone and/or vibration stop and the caller’s voice can be heard in the earpiece.
Tip: You can set your phone to answer calls when you open the folder, when you press any key but the
key, or automatically. (See “Call
Options” on page 154 for more information.
Ignoring a Call
When you ignore an incoming call, the call is immediately forwarded to your voice mail.
â– During an incoming call, press the Ignore (left) soft key
( ). The caller is forwarded to your voice mail.
Adjusting the Call Volume
In standby mode, repeatedly press the volume key ( ) down until the Call Volume Level desired appears in the display. The volume key is on the left side of phone.
30
Calls Log
Calls Log
The Calls log retains information about Outgoing,
Incoming, and Missed calls. You can also view times for your last call and the time totals for all calls.
Review the Calls Log
1. In standby mode, press the Menu (left) soft key ( ), then press the key (for Calls). The following options appear in the display:
䢇 Press
䢇 Press for Outgoing calls. for Incoming calls.
䢇
䢇
䢇
䢇 for Data Counter.
2. Press the number key associated with the Calls log that you wish to review or the function you wish to access.
Note: In cases where there is a Contacts match for a Calls log entry, the name associated with the number appears in the display instead of the number.
Outgoing Calls
Your phone retains information about the last 20 outgoing calls and stores them in the Outgoing calls log. You can review the Outgoing calls log for the time and date of a call, as well as other information.
Note: To quickly view your most recent calls, briefly press in standby mode. Up to 20 of your most recent outgoing, incoming, and missed calls appear in the display.
Section 3: Call Functions 31
1. In standby mode, press the Menu (left) soft key ( ), then press (for Calls) and for Outgoing. A list of your outgoing calls appears in the display.
2. Use the navigation keys to highlight a call, then press the
key to view further information about the call.
3. Press the Option (left) soft key ( ). A pop-up menu appears in the display containing the following options:
䢇 Talk—Call the selected number.
䢇 Save—Save the number to your Contacts.
䢇 Prepend—Add a prefix to the number.
䢇 Erase—Erase the selected call from your Outgoing call log.
4. Use the navigation keys to highlight an option.
5. Press the key to perform the highlighted option’s function.
Incoming Calls
Your phone retains information about the last 20
Incoming calls and stores them in the Incoming call log.
You can review the Incoming call log for the time and date of the call, as well as other information.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Calls) and for Incoming. A list of your Incoming calls appears in the display.
2. Use the navigation keys to highlight a call, then press the
key to view further information about the call.
32
Calls Log
3. Press the Option (left) soft key ( ). A pop-up menu appears in the display containing the following options:
䢇 Talk—Call the selected number
䢇 Save—Save the number to your Contacts
䢇 Prepend—Add a prefix to the number
䢇 Erase—Erase the selected call from your incoming call list.
4. Use the navigation keys to highlight an option.
5. Press the key to perform the highlighted option’s function.
Missed Calls
Your phone retains information about the last 20 missed calls (call that were never picked up) and stores them in the Missed call log. You can review the Missed call log for the time and date of the call, as well as other information.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Calls) and for Missed. A list of your missed calls appears in the display.
2. Use the navigation keys to highlight a call, then press the
key to view further information about the call.
3. Press the Option (left) soft key ( ). A pop-up menu appears in the display containing the following options:
䢇 Talk—Call the selected number.
䢇 Save—Save the number to your Contacts.
䢇 Prepend—Add a prefix to the number.
䢇 Erase—Erase the selected call from your incoming call list.
4. Use the navigation keys to highlight an option.
Section 3: Call Functions 33
5. Press the key to perform the highlighted option’s function.
Erase Logs
You can erase the Outgoing, Incoming, or Missed calls log or you can erase All Calls.
Erase All Calls
1. In standby mode, press the Menu (left) soft key ( ), then press
for Erase All Calls.
“Erase All Calls?” appears in the display as well as the following options:
䢇 Yes—Erases all calls in the Calls log.
䢇 No—Cancels erasing calls.
2. Use the navigation keys to highlight the desired option, then press the key.
Call Timer
View the duration of your last call, total calls, and calls made during the life cycle of you phone using the Call
Timer feature.
Note: Call Timer is not for billing purposes.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Calls) and for Call Timer. The following options appear in the display:
䢇 Last Call—View the duration of your last call.
䢇 Total—View the duration of the total call, incoming and outgoing, made on your phone since the last erasure.
34
Phone Modes
䢇 LifeTime—View the duration of all calls on your phone since activation (LifeTime timers cannot be erased).
䢇 Erase Total—Erases the counters for the Total call timer.
Press the number of the option you wish enter, or use the navigation keys to highlight the option and press the key.
2. Press the key if you wish to exit the menu.
Note: Although Total call timers can be erased, LifeTime call timers can never be erased.
Phone Modes
Standby Mode
Standby mode is the state of your phone once it is powered on and has found a wireless service. Your phone goes into standby mode:
• After you power the phone on.
• When you press the key after a call or from within a menu or phone function screen.
When in standby mode, you will see the time, day, and date in the display as well as all currently active icons.
When in standby mode, you can:
• Make calls.
• Receive calls and messages.
• Access your phone’s menus.
• Change your phone’s mode.
• Activate Voice Command.
Section 3: Call Functions 35
Receive Messages in Standby Mode
You can receive messages while in standby mode. An alert tone sounds and a notification message appears in the display when a new message arrives.
• Press the View (right) soft key ( ) to view the message now.
• Press the Ignore (left) soft key ( ) to view the message later.
Talk Mode
While in a call your phone is in talk mode. Press the left soft key ( ) to display a list of In-Use menu options.
(See “In Use Menu Outline” on page 44 for more
information).
Lock Mode
When you lock your phone using the Lock Mode menu
option (see “Lock Phone” on page 143 for more
information), the following restrictions are placed on use of your phone:
• You can receive messages and calls.
• You cannot make outgoing calls (except for emergency numbers).
• You cannot access your phone’s menus.
• The volume key is disabled.
Unlock your phone by following the prompts and entering the lock code.
Silent Mode
With a single press of the key you can silence the call ringer and tones that your keypad makes whenever you press a key.
36
Phone Modes
When you receive a call, the phone vibrates instead of ringing.
Enter Silent Mode
â– In standby mode, press and hold the key.
“Entering Silent Mode” briefly appears in the display and your phone returns to standby mode.
The Silent Mode icon ( ) appears in the top line of the display.
Exit Silent Mode
â– In standby mode, press and hold the key.
“Exit Silent Mode” briefly appears in the display and your phone returns to standby mode.
Vibrate Mode
You can set your phone to vibrate whenever you receive an incoming call using either of the following methods:
â– In standby mode, repeatedly press the Down volume key
( ) until Vibrate appears in the display. or do the following:
1. In standby mode, press the Menu (left) soft key ( ), then press Volume/
Vibrate), and for Calls.
2. Press the Left navigation keys until “Vibrate” appears in the display, then press the key.
Section 3: Call Functions 37
Text Input Modes
You use your phone’s text input modes (ABC, Symbol,
123, or T9 WORD) to enter text, numbers, or symbols into messages, events, and other functions. The current text input mode is indicated in the lower right part of the display.
Note: See “Section 5: Entering Text” on page 53 for more information
about text input modes.
ABC Mode
Enter characters while in ABC mode by pressing the key with the desired characters (such as for “a”).
• Press the key repeatedly until the desired character (letter, number, or symbol) appears in the display.
• Pause briefly and the displayed character is accepted and inserted into your message.
• Press to enter a space.
Tip: To enter large numbers of symbols or numbers quickly, use Symbol mode or 123 mode as described in the following sections.
Symbol Mode
Symbol mode lets you use keypad number keys to enter symbols such as @ or % into a text message, event, or e-mail address without going through repeated key presses as with ABC mode.
You press the key that corresponds with the symbol that you wish to enter. For example, press exclamation point (!).
for an
38
Phone Modes
123 Mode
123 mode lets you use keypad number keys to enter numbers into a text message, event, or e-mail address without going through repeated key presses as with
ABC mode.
T9 Word Text Entry Mode
T9 Word recognizes a commonly used word that is represented by a sequence of number key presses and inserts that word into your message. (For example, entering ‘8378’ would insert ‘test’ into your message.)
Using T9 Word is much faster than the more traditional text input method (ABC mode) and requires only one press of a key per letter of the word that you’re entering. (For example, in ABC mode, you would have to enter ‘83377778’ for ‘test’ instead of entering ‘8378’ for ‘test’ as in T9 Word mode.)
Note: See “Using T9 Mode” on page 56 for more information about using
the T9 Word text input mode.
Section 3: Call Functions 39
Roaming
What is Roaming
Roaming lets you use your SCH-a570 phone when you travel outside of your Wireless Provider’s coverage area. The Roaming icon ( ) appears in the top line of the display when Roaming is active, and extra charges may apply when making or receiving calls.
Note: Some features may be unavailable while roaming. Roaming also consumes additional power from the battery requiring more frequent recharging. Contact your Wireless Provider for more information about
Roaming.
How Roaming Works
Roam Option lets you set roaming preferences if you move in and out of your home network. The following roaming options are available:
• Home only—Your phone is available for normal operation only in the designated coverage area.
• Automatic—Your Wireless Provider’s Preferred Roaming List
(PRL) of networks is used to acquire service. If no preferred networks are found, any digital system is acquired.
40
Section 4: Menu Navigation
Topics Covered
• Menu Navigation
• In Use Menu Outline
• Menus and sub-menus
This section explains the menu navigation for your phone. It also includes an outline of all the available menus associated with your phone.
Section 4: Menu Navigation 41
Menu Navigation
You access the menus and sub-menus in your phone by using the navigation keys ( ), soft keys ( ), or a shortcut.
Navigate Using Keys
1. In standby mode, press the Menu (left) soft key ( ).
The Main menu (the first of several menus) appears in the display.
2. Use the navigation keys to browse through the menus in your phone.
3. Press the key to select a menu or sub-menu that then appears in the display.
Return to the Previous Menu
There are two methods for exiting a menu or list.
• Press the Back (right) soft key ( ).
• Press the Clear key ( ).
Navigate Using a Shortcut
You can also access menus and sub menus using menu numbers. This method is often called a “shortcut.” To shortcut to a menu or sub menu, press the Menu (left) soft key ( ), then enter the menu and/or sub menu
number(s) for the feature in question. Use “Navigation
Key Shortcuts” on page 43, for looking up the menu
shortcut number.
Note: Use the list of menus and sub-menus, which begins on page 45, to
navigate using shortcuts.
42
Menu Navigation
1. In standby mode, press the Menu (left) soft key ( ).
The Main menu appears in the display.
2. Press the number of the menu, sub-menu, and so on for the feature that you wish to access.
Example: Press the key, then press the key and then the key. This takes you to the Tools
(Menu 8), and then to the To Do List (sub-menu 4).
Navigation Key Shortcuts
Some applications can be launched by pressing one of the four navigation keys (see the illustration) while in standby mode. The Up key (defaulted to Calendar) can be customized in the Shortcut menu , , .
Section 4: Menu Navigation 43
In Use Menu Outline
Your phone includes both a Main menu and an In-Use
Menu. The In-Use Menu is accessible only when you are in a call.
1. Press the Menu (left) soft key ( ), while in a call to display the following options.
䢇 Calls —Checks your call log for outgoing, incoming, and missed calls. You can also erase your call logs from this menu.
䢇
Contacts —Accesses Contacts menu options.
䢇 Voice Memo —Allows to record, and save memos.
䢇 Silent/Quit —Activates or deactivates Silent Mode. In Silent
Mode, your phones ringer is silent and keypad tones are also muted. This feature should not be used when you access automated services that require you to select options, or enter numbers (such as your voice mail password).
䢇
Send Tel# —Send your phone number to the other party of the call.
䢇 Send DTMF —Send your phone number as tones (if you’re the recipient of the call). Send the recipient’s phone number as tones (if you’re the originator of the call).
䢇
Voice Privacy —Set Voice Privacy to enhanced or standard mode. Voice Privacy prevents the receiving party from seeing your number when you call.
䢇
Location —Enable the GPS setting for emergency calls only, or fully enable GPS (always on).
䢇 Version —View the software and hardware versions for your phone.
Note: You can mute the microphone on your phone by pressing the Mute
(left) soft key ( ). To unmute, press the Menu (left) soft key ( ), then the
Unmute (left) soft key ( ).
44
Menus and sub-menus
2. Use the navigation keys to highlight an option. Press the
key to select the In-Use Menu option of your choice.
Menus and sub-menus
1 My Metro
1.1
Monthly Bill
1.2
MetroConnect
1.3
MetroPCS Card
1.3.1 Request Balance
1.3.2 Pay Monthly Bill
1.3.2.1
1.3.2.2
1.3.2.3
Credit Card
MetroPCS Card
Other Options
2 Contacts
2.1
Find
2.2
Add
2.2.1 Number
2.2.2 E-Mail
2.3
Rename Group
2.3.1 Friend
2.3.2 Family
2.3.3 Colleague
2.3.4 VIP
2.3.5 No Name
2.4
My Phone#
2.5
Memory
Section 4: Menu Navigation 45
3 Messages
3.1
Send New Msg
3.2
Voice Mail
3.3
Inbox
3.4
Outbox
3.5
Draft
3.6
Saved
3.7
Wap Push
3.8
Msg Setting
3.8.1 Send Setting
3.8.1.1
3.8.1.2
3.8.1.3
3.8.1.4
3.8.1.5
Save In Outbox
Callback#
Entry Mode
Insert Sign.
Delivery Ack
3.8.2 Msg. Alert
3.8.2.1
3.8.2.2
3.8.2.3
Volume/Vibrate
Ringer Type
3.8.2.2.1
3.8.2.2.2
3.8.2.2.3
3.8.2.2.4
3.8.2.2.5
Voice Mail
Page
Text Msg
Wap Push
Alert On Call
Reminder
3.8.3 Auto Play
3.8.4 Auto View
3.8.5 Auto Erase
3.8.6 Block/Unblock
3.8.6.1
3.8.6.2
3.8.6.3
Block
Unblock
View Blocked List
46
Menus and sub-menus
3.8.7 Quick Text
3.8.8 Signature
3.9
Erase Msg
3.9.1 Voice
3.9.2 Inbox
3.9.3 Outbox
3.9.4 Draft
3.9.5 Saved
3.9.6 All Messages
4 Mobile Web
4.1
Get In Web
5 Calls
5.1
Outgoing
5.2
Incoming
5.3
Missed
5.4
Erase Logs
5.4.1 Outgoing
5.4.2 Incoming
5.4.3 Missed
5.4.4 All Calls
5.5
Call Timer
5.5.1 Last Call
5.5.2 Total
5.5.3 LifeTime
5.5.4 Erase Total
5.6
Data Counter
Section 4: Menu Navigation 47
5.6.1 Transmit
5.6.2 Received
5.6.3 Total
5.6.4 Erase Total
6 @metro
6.1
@metro
7 Sounds
7.1
Volume/Vibrate
7.1.1 Calls
7.1.2 Alarm
7.2
Ringer Type
7.2.1 Calls
7.2.2 Alarm
7.2.3 Data
7.2.4 Calendar
7.3
Key Beep
7.3.1 Volume
7.3.2 Tone Length
7.4
Alerts
7.4.1 Minute Beep
7.4.2 Service
7.4.3 Connect
7.4.4 Disconnect
7.4.5 Fade
7.4.6 Roam
7.4.7 Privacy
48
Menus and sub-menus
7.5
Power On/Off
7.6
Roam Ringer
7.7
Whisper Mode
8 Tools
8.1
Voice
8.1.1 Voice Command
8.1.2 Voice Memo
8.1.2.1
8.1.2.2
8.1.2.3
8.1.3 TTS
Record
Review
Erase All
8.1.4 Voice Setting
8.1.4.1
8.1.4.2
8.1.4.3
8.1.4.4
8.1.4.5
8.1.4.6
Digit Dialing
8.1.4.1.1
8.1.4.1.2
Adapt Digits
Reset Digits
Sensitivity
8.1.4.2.1
8.1.4.2.2
Commands
Names
Choice Lists
8.1.4.3.1
8.1.4.3.2
8.1.4.3.3
Name Dialing
Digit Dialing
Contacts
Sound
8.1.4.4.1
8.1.4.4.2
8.1.4.4.3
8.1.4.4.4
Voice Launch
Prompts
Digits
Names
Name Settings
About
8.2
Today
8.3
Calendar
8.4
To Do List
Section 4: Menu Navigation 49
8.5
Alarm Clock
8.5.1 Alarm Clock 1
8.5.2 Alarm Clock 2
8.5.3 Alarm Clock 3
8.6
Memo Pad
8.7
World Time
8.8
Calculator
8.9
Count Down
9 Set Up
9.1
Location
9.2
Network
9.2.1 Set NAM
9.2.2 Roam Option
9.3
Security
9.3.1 Lock Phone
9.3.2 Change Lock
9.3.3 Emergency #
9.3.4 Voice Privacy
9.3.5 Restriction
9.3.5.1
9.3.5.2
9.3.5.3
Outgoing Call
Incoming Call
Contacts
9.3.6 Erase Memory
9.3.7 Reset Phone
9.4
Display
9.4.1 Menu Style
9.4.2 Animation
50
Menus and sub-menus
9.4.2.1
9.4.2.2
9.4.2.3
Opening
9.4.2.1.1
9.4.2.1.2
Closing
9.4.2.2.1
9.4.2.2.2
Wallpaper
9.4.2.3.1
9.4.2.3.2
9.4.3 Banner
9.4.4 Backlight
9.4.4.1
9.4.4.2
9.4.4.3
LCD
Keypad
Power save
9.4.5 Contrast
9.4.5.1
9.4.5.2
Main LCD
Front LCD
9.4.6 Auto Hyphen
9.4.7 Dial Digits
9.4.8 Dial Screen
9.4.9 Service LED
Preloaded
My Image
Preloaded
My Image
Preloaded
My Image
9.5
Call Options
9.5.1 Call Answer
9.5.2 Auto Answer
9.5.3 Auto Retry
9.5.4 Data
9.5.4.1
9.5.4.2
Auto Detect
Baud Rate
9.5.5 TTY Mode
9.6
Shortcut
9.7
Language
Section 4: Menu Navigation 51
52
9.8
Clock Set
9.9
Version
Section 5: Entering Text
Topics Covered
• Text Entry Mode
• Entering Upper and Lower Case Letters
• Entering Symbols
• Entering Numbers
• Using T9 Mode
• Changing the Text Entry Mode
This section outlines how to select the desired text input mode when entering characters into your phone. This section also describes how to use the T9 predictive text entry system to reduce the amount of key strokes associated with entering text.
Section 5: Entering Text 53
Text Entry Modes
You can compose text messages using alphabetical characters, symbols, and numbers. Each method of character entry (symbol, number, and so on) is called a text entry mode. There are four text entry modes, as indicated:
• ABC—Alphabetical text entry mode. Options are:
䢇 ABC—All upper case
䢇 Abc—Initial capital
䢇 abc—All lower case
• Symbol—Symbol entry mode. Enter symbols into your message by pressing the corresponding number that appears above it in the display.
• 123—Number entry. Enter numbers by pressing the corresponding key on the keypad.
• T9 Word—Predictive text mode. Press each key only once to enter the letter of the word that you’re spelling.
Your current mode of text entry (ABC, Symbol, 123, or
T9 Word ) is indicated in the lower right part of the display when composing a text message.
Entering Upper and Lower Case Letters
1. Enter characters while in ABC mode by pressing the key with the desired characters (such as, pressing
“g”).
for
2. Press the key repeatedly until the desired character appears in the display (such as, pressing two times for “h”).
54
Entering Symbols
3. Pause briefly and the displayed character is accepted and inserted into your message.
4. Press the key to enter a space.
Entering Symbols
Symbol mode enables you to enter symbols such as @ or % in a text message.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Messages) and (for Send
New Msg) to compose a new text message.
2. Enter the phone number of the recipient, then press the
key.
3. Press the Option (left) soft key ( ). A pop-up menu appears in the display containing the following options:
䢇 ABC
䢇 Quick Text
4. ABC is highlighted. Use the Left and Right navigation keys to display Symbol, then press the key. The first of four screens of symbols appear in the display.
5. Use the Left and Right navigation keys to page through the other symbols, if necessary.
6. Enter the key that corresponds with the symbol that you wish to enter. For example, press for an exclamation point (!).
7. Repeat steps 3 through 6 to insert as many symbols into your message as desired.
Section 5: Entering Text 55
Entering Numbers
Enter numbers into a text message while in number
â– While in 123 mode, press the key containing the corresponding number that you wish to insert into your message.
Using T9 Mode
T9 Word recognizes commonly used words for the numeric sequence of keypresses and inserts the word into your message. It’s much faster than the traditional method of text entry (ABC mode) and requires only one
key press per letter of the word that you’re spelling.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Messages) and (for Send
New Msg) to compose a new text message.
2. Enter the phone number of the recipient, then press the
key.
3. Press the Option (left) soft key ( ). A pop-up menu appears in the display containing the following options:
䢇 ABC
䢇 Quick Text
56
Changing the Text Entry Mode
4. ABC is highlighted. Use the Left and Right navigation keys to display T9 Word, then press the key.
Now, for practice, enter the work ‘Samsung’ into your message by pressing each of the following keys only once:
S A M S U N G
T9 Word recognizes that the most commonly used word for the numeric sequence you just entered is
“Samsung.”
Note: If more than one word shares the same numeric sequence (such as,
“263” for both “and” and “cod”), T9 Word provides the most commonly used word (such as, “and” for “263”). Press the words, if any are available.
key to display other
Changing the Text Entry Mode
1. While composing a text message, press the Option (left) soft key ( ). A pop-up menu appears in the display containing the following options:
䢇 ABC
䢇 Quick Text
ABC is highlighted. Use the Left and Right navigation keys to choose from one of the other three text entry modes of Symbol, 123, or T9 Word. Each of the text
entry modes are explained in greater detail in ‘Section 9:
Section 5: Entering Text 57
58
Section 6: Understanding Your Contacts
Topics Covered
• Your Contacts List
• Adding a New Contacts Entry
• Finding a Contacts Entry
• Editing an Existing Contacts Entry
• Renaming a Contacts Group
• Deleting a Contacts Entry
• Finding My Phone Number
• Memory
This section explains how to manage your daily contacts by storing their name and number in your
Contacts. Contacts entries can be sorted by name, entry, or group.
Section 6: Understanding Your Contacts 59
Your Contacts List
Your Contacts list can store up to 500 numbers, with each contact having up to five associated phone numbers, an e-mail address, and a picture ID.
Each phone number can be up to 20 digits in length, including hard pauses. Contact names can be up to 22 characters in length. You can also specify a memory location for each entry, and you can restrict access to the
Contacts list to prevent unauthorized use.
Tip: One-Touch, Two-Touch, and Three-Touch Dialing allow you to call
numbers stored in your Contacts list faster. (See page 25.)
Open Your Contacts List
1. In standby mode, press the Menu (left) soft key ( ), then press for Contacts. The following Contacts sub-menus and options appear in the display:
䢇 Find—Find a phone number By Name, By Entry, or By Group.
䢇 Add—Add a number or e-mail to your Contacts.
䢇 Rename Group—Rename one of your five groups.
䢇 My Phone#—View the 10-digit number assigned to your phone by your Wireless Provider.
䢇 Memory—View available memory for dial entries.
Note: You can also access your Contacts list from standby mode by pressing the Contacts (right) soft key ( ). The Contacts Find screen appears in the display.
2. Use the navigation keys to highlight the Contacts submenu or option of your choice, and press the key.
60
Adding a New Contacts Entry
Tip: You can also access a sub-menu or menu option by pressing the number key corresponds to the menu item number. For example, press
for Add.
Adding a New Contacts Entry
You can add an entirely new entry to your Contacts list or add information to an existing entry.
Using the Contacts Add Option
1. In standby mode, press the Menu (left) soft key ( ), then press (for Contacts) and for Add. The following options appear in the display:
䢇 Number—Lets you enter a number to be dialed when calling the new contact.
䢇 E-mail—Lets you enter an e-mail address for the new contact.
2. Use the navigation keys to highlight the desired option and press the key.
3. Enter the phone number or e-mail address for the new
Contacts entry, then press the key. The following options appear in the display:
䢇 New Entry—Lets you create a new Contacts entry.
䢇 Find—Lets you add the number or e-mail address you just entered to an existing Contacts entry.
Section 6: Understanding Your Contacts 61
4. Use the navigation keys to highlight New Entry, then press the key. The following (number type) icons appear in the display:
Home Office Mobile
Pager Fax
5. Use the navigation keys to highlight the number type that matches your new entry and press the key. The
Contacts information screen appears in the display with the Name field highlighted.
6. Enter a name or phrase to associate with the type using
the keypad. (See “Section 5: Entering Text” on page 53
for more information.)
7. Press the key to save the entry.
Adding Pauses to Contacts Numbers
When you call automated systems (like banking services), you are often required to enter a password or account number. Instead of manually entering the numbers each time, you can store the numbers in your
Contacts along with special characters called pauses.
• P pause—A hard pause stops the calling sequence until further input from you.
• T pause—A two-second pause stops the calling sequence for two seconds and then automatically sends the remaining digits.
Tip: You can enter multiple two-second pauses to extend the length of a pause. For example, two consecutive two-second pauses cause a total pause time of four seconds.
62
Adding a New Contacts Entry
Note: Keep in mind that pauses count as digits towards the 20-digit maximum.
Store Pauses in a Contacts Entry
1. In standby mode, enter the number you wish to store
(such as your bank’s teleservice number).
2. Press the Option (left) soft key ( ). The following pause menu options appear in the display:
䢇 P pause—a hard pause (awaits input from you).
䢇 T pause—a two-second pause.
P pause is highlighted.
3. Use the navigation keys to highlight the pause option of your choice.
4. Press the key to enter the highlighted pause into your number sequence.
5. When you’re finished entering the number and pauses, press the Save (right) soft key ( ) to store the number in your Contacts.
Saving a Number from a Call
Once you’ve finished a call, you can save the number of the caller to your Contacts list.
Note: If the call was incoming and Caller ID information was unavailable, then the Save option is also unavailable.
1. After you press the key to end your call, the call time, length of call, phone number, and name of the other party (if available) appear in the display.
Section 6: Understanding Your Contacts 63
2. Press the Save (right) soft key ( ). The following options appear in the display:
䢇 New Entry—Lets you create a new Contacts entry.
䢇 Find—Lets you add the number or e-mail address you just entered to an existing Contacts entry.
Tip: You can also store a phone number by entering the number, and pressing the Save (right) soft key ( ).
3. Use the navigation keys to highlight New Entry, then press the key. The following (number type) icons appear in the display:
Home Office Mobile
Pager Fax
4. Use the navigation keys to highlight the number type that matches your new entry and press the key. The
Contacts information screen appears in the display with the Name field highlighted.
5. Enter a name or phrase to associate with the type using
the keypad. (See “Section 5: Entering Text” on page 53
for more information.)
6. Press the key to save the entry.
Storing Number from a Calls Log
You can store numbers from the Calls logs to your
Contacts.
1. In standby mode, press the Menu (left) soft key ( ), then press for Calls.
64
Adding a New Contacts Entry
2. Press the corresponding number on the keypad to view the following Calls logs:
䢇
䢇
䢇
A list of your calls appears in the display.
3. Use the navigation keys to highlight the number you wish to store in Contacts, then press the key.
4. Press the Option (left) soft key ( ).
5. Use the navigation keys to highlight Save, then press the
key. The following options appear in the display:
䢇 New Entry—Lets you create a new Contacts entry.
䢇 Find—Lets you add the number or e-mail address you just entered to an existing Contacts entry.
6. Use the navigation keys to highlight New Entry, then press the key. The following (number type) icons appear in the display:
Home Office Mobile
Pager Fax
7. Use the navigation keys to highlight the number type that matches your new entry and press the key. The
Contacts information screen appears in the display with the Name field highlighted.
8. Enter a name or phrase to associate with the type using
the keypad. (See “Section 5: Entering Text” on page 53
for more information.)
Section 6: Understanding Your Contacts 65
9. Press the key to save the entry.
Finding a Contacts Entry
Voice Method
Use the VoiceSignal Contacts command to view contact information for any named contact stored in your
Contacts list by saying the name.
Note: The Contacts command shows the requested contact information in the display but does not dial any phone numbers for the contact.
To look up information for a specific contact:
1. In standby mode, press and hold the key to launch
VoiceSignal.
“Say a Command” appears in the display and is pronounced through the speaker.
2. Say “Contacts”.
VoiceSignal prompts you to “Say the name.”
3. Speak clearly and say the full name of the person you want to call, exactly as it is entered in your contact list.
䢇 If VoiceSignal recognizes the name you said, the contact information for that name appears in the display.
䢇 If VoiceSignal does not recognize the name you said, a choice list of up to three names appears in the display, and
VoiceSignal prompts you with “Did you say?” followed by the first name on the list.
66
Finding a Contacts Entry
4. Say “Yes” to confirm the name or “No” to hear the next name, or use the keypad to select the correct name from
the list. (See “Choice Lists Settings” on page 118, for
more information.)
䢇 To say the name again, press the Repeat (right) soft ( ) key.
䢇 To exit VoiceSignal without dialing, press the Settings (left) soft
( ) key and press the Cancel (right) soft ( ).
5. The contact information for the name you selected appears in the display.
Menu Method
If you’ve stored a named contact in your Contacts list,
Find lets you locate the entry quickly.
1. In standby mode, press the Contacts (right) soft key
( ). The Find screen appears in the display with By
Name showing.
2. Use the navigation keys to select the method you wish to use to find the entry. The available Find methods are:
䢇 By Name—Search the Contacts alphabetically by name.
䢇 By Entry—Search the Contacts by entry number.
䢇 By Group—Search the Contacts by selecting from one of the five available groups.
Find by Name
This option lets you find a Contacts list entry by its contact name.
1. In the Find screen, use the navigation keys to show By
Name in the display.
2. Enter the name of the contact as it appears in your
Contacts list.
Section 6: Understanding Your Contacts 67
Example: If you saved a contact name as “Amy Smith”, begin your search for that contact by pressing for “A”.
Note: As you enter letter, the entry number and names of the closest matches (thus far) appear in the display.
3. When the desired Contacts entry is listed in the display, highlight the contact using the navigation keys (if necessary). Then:
Press the key to dial the number associated with the named contact.
Or
Press the key to view information about the contact.
Or
Press the Option (left) soft key ( ). The following options appear in the display:
䢇 Talk—Dials the selected contact.
䢇 Edit—Lets you edit details of the highlighted name.
䢇 Send Msg—Lets you send an SMS message to the selected number.
䢇 Erase—Erases the selected Contacts entry.
4. Use the navigation keys to highlight an option, then press the key to enter that option’s sub-menu.
68
Finding a Contacts Entry
Find by Entry
This option lets you find a Contacts list entry by its
Location number.
1. In the Find screen, use the navigation keys to show By
Entry in the display.
2. When the desired Contacts entry is listed in the display, highlight the contact using the navigation keys (if necessary). Then:
Press the key to dial the number associated with the named contact.
Or
Press the key to view information about the contact.
Or
Press the Option (left) soft key ( ). The following options appear in the display:
䢇 Talk—Dials the selected contact.
䢇 Edit—Lets you edit details of the highlighted name.
䢇 Send Msg—Lets you send an SMS message to the selected number.
䢇 Erase—Erases the selected Contacts entry.
3. Use the navigation keys to highlight an option, then press the key to enter that option’s sub-menu.
Find by Group
This option lets you find a Contacts list entry with a specific Group name.
1. In the Find screen, use the navigation keys to show By
Group in the display.
Section 6: Understanding Your Contacts 69
70
2. Use the navigation keys to highlight the Group field.
3. Use the navigation keys to show the name of the group you wish to search. As each group name appears in the display, entries that are assigned that group name are listed in the display beneath it.
4. When the desired Contacts entry is listed in the display, highlight the contact using the navigation keys (if necessary). Then:
Press the key to dial the number associated with the named contact.
Or
Press the key to view information about the contact.
Or
Press the Option (left) soft key ( ). The following options appear in the display:
䢇 Talk—Dials the selected contact.
䢇 Edit—Lets you edit details of the highlighted name.
䢇 Send Msg—Lets you send an SMS message to the selected number.
䢇 Erase—Erases the selected Contacts entry.
5. Use the navigation keys to highlight an option, then press the key to enter that option’s sub-menu.
Editing an Existing Contact Entry
Editing an Existing Contact Entry
Once stored in the Contacts, an entry can be changed quite easily.
1. In standby mode, press the Contacts (right) soft key
( ). The Find screen appears in the display with By
Name showing.
2. Use the navigation keys to display the search method that you wish to use (By Name, By Group, or By Entry).
3. Enter information to find the Contacts list entry, or use the navigation keys to highlight the entry containing the number that you wish to edit.
4. Once the entry is highlighted, press the key.
5. Use the navigation keys to highlight the number within the entry that you wish to edit.
6. Press the Option (left) soft key ( ). The following options appear in the display:
䢇 Talk—Dial the selected number.
䢇 Edit—Edit selected number.
䢇 Send Msg—Send an SMS message to the selected number.
䢇 Erase—Erase the selected number.
7. Use the navigation keys to highlight Edit, then press the
key.
8. Press to backspace and delete numbers.
9. Press and hold to clear all numbers in the highlighted field.
Section 6: Understanding Your Contacts 71
10. When you’re finished editing the number, press the key. Your changes are saved and a confirmation message appears in the display.
Assigning Speed Dial Numbers
When you add an entry to the Contacts list, you have the option of letting the phone assign a Location (Speed
Dial) number or of selecting or entering a Location number. You can also change a contact’s Location number.
1. In standby mode, press the Contacts (right) soft key
( ). The Find screen appears in the display with By
Name showing.
2. Use the navigation keys to display the search method that you wish to use (By Name, By Group, or By Entry).
3. Enter information to find the Contacts list entry, or use the navigation keys to highlight the entry containing the
Location number that you wish to change.
4. Once the entry is highlighted, press the key.
5. Use the navigation keys to highlight SpeedDial.
6. With SpeedDial highlighted, press the Edit (left) soft key
( ).
7. Enter the new SpeedDial Location number.
8. Press the key to save your changes.
Add a Number or E-mail Address to an Existing Entry
1. In standby mode, press the Menu (left) soft key ( ), then press (for Contacts) and for Add. The following options appear in the display:
72
Editing an Existing Contact Entry
䢇 Number—Lets you enter a number to be dialed when calling the new contact.
䢇 E-mail—Lets you enter an e-mail address for the new contact.
2. Use the navigation keys to highlight the desired option and press the key.
3. Enter the phone number or e-mail address for the new
Contacts entry, then press the key. The following options appear in the display:
䢇 New Entry—Lets you create a new Contacts entry.
䢇 Find—Lets you add the number or e-mail address you just entered to an existing Contacts entry.
4. Use the navigation keys to highlight Find, then press the
key.
5. Use the navigation keys to show the search method that you wish to use (By Name, By Group, or By Entry).
6. Enter information to find the entry and/or use the navigation keys to highlight the desired entry and press the key. The following number types appear in the display:
Home Office Mobile
Pager Fax
7. Use the navigation keys to highlight the number type that matches the number you are adding, then press the key.
8. Press the key again at the Contacts menu. The number is added to the existing entry.
Section 6: Understanding Your Contacts 73
Edit an Existing E-mail Address
1. In standby mode, press the Contacts (right) soft key
( ). The Find screen appears in the display with By
Name showing.
2. Use the navigation keys to display the search method that you wish to use (By Name, By Group, or By Entry).
3. Enter information to fine the entry, or use the navigation keys to highlight the entry that you wish to edit.
4. Once the entry is highlighted, press the left soft key ( )
Option. A pop-up menu appears in the display with Edit highlighted.
5. Press the key.
6. Use the navigation keys to highlight the E-mail field.
7. Use the keypad to edit the E-mail address. (See “Section
5: Entering Text” on page 53 for more information.)
To insert the @ symbol, press the Option (left) soft key
( ). A pop-up menu appears in the display with ABC highlighted.
8. Use the navigation keys to select Symbol. Then press
74
e-mail address using the keypad. (See “Section 5:
Entering Text” on page 53 for more information.)
10. Press the left soft key ( ) Option.
11. Use the navigation keys to highlight .com, then use the navigation keys to show the desired domain type (.com,
.edu, .net), then press the key.
Renaming a Contacts Group
12. Press the key to save your changes.
Renaming a Contacts Group
Use this option to rename a group in your Contacts list.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Contacts) and for Rename
Group. The following default group names (or any changed group names) appear in the display:
䢇 Friend
䢇 Family
䢇 Colleague
䢇 VIP
䢇 No Name
2. Use the navigation keys to highlight the group that you wish to rename, then press the key. The current name of the group appears in the display with a flashing cursor at the end of the name.
3. Enter a new group name using the keypad, then press the
key. (See “Section 5: Entering Text” on page 53
for more information.)
Deleting a Contact Entry
1. In standby mode, press the Contacts (right) soft key
( ). The Find screen appears in the display with By
Name showing.
2. Use the navigation keys to display the search method that you wish to use (By Name, By Group, or By Entry).
Section 6: Understanding Your Contacts 75
3. Enter information to find the entry, or use the navigation keys to highlight the entry that you wish to erase.
4. Press the Option (left) soft key ( ). A pop-up menu containing the following options appears in the display:
䢇 Talk—Dial the selected number.
䢇 Edit—Edit selected number.
䢇 Send Msg—Send an SMS message to the selected number.
䢇 Erase—Erase the selected number.
5. Use the navigation keys to highlight Erase.
6. Press the key. The phone prompts you to confirm the erasure.
7. Use the navigation keys to highlight Yes or No, then press the key.
Finding My Phone Number
My Phone# displays the ten-digit number assigned to your phone by your Wireless Provider.
â– In standby mode, press the Menu (left) soft key ( ), then press (for Contacts) and for My Phone#.
The phone number assigned by your Wireless Provider appears in the display.
76
Memory
Memory
Use the Memory sub-menu to view the amount of
Contacts entries you have stored, as well as the remaining memory.
â– In standby mode, press the Menu (left) soft key ( ), then press (for Contacts) and for Memory.
The amount of memory used and remaining for Contacts entries appear in the display.
Section 6: Understanding Your Contacts 77
78
Section 7: @metro
Topics Covered
• @metro Catalog
• Settings
• Help
This section provides explanations of how you can use
@metro on your phone to do the following:
• Download full featured applications over the air including games, personalized ring tones, pictures, and more; and
• Browse the web to catch up on all the latest news.
Section 7: @metro 79
@metro Catalog
1. In standby mode, press the right navigation key ( @). The
@metro menu containing the following icons appears in the display:
@metro Access @metro catalog.
Settings View and change @metro settings.
Help View @metro tutorials.
The @metro icon ( ) is highlighted.
2. Press . A connection message pop-up appears in the display, then the @metro Catalog menu containing the following options appears in the display:
• New Arrivals
• Featured Apps
• @pics
• @tones
• @games
• @info
• SPANISH
• search
3. Use the navigation keys to highlight the category you want, then press .
4. Select the application you want to download and follow the online directions.
80
Settings
Settings
Use the Settings menu within @metro to manage, move, order applications, and much more.
1. In standby mode, press the right navigation key ( @). The
@metro menu containing the following icons appears in the display:
@metro Access @metro catalog.
Settings View and change @metro settings.
Help View @metro tutorials.
The @metro icon ( ) is highlighted.
2. Use the navigation keys to highlight the Settings icon
( ), then press . The options listed in the following table appear in the display.
• Order Apps—Download applications over the network.
• Move Apps—Move previously downloaded applications between available folders.
• Manage Apps—View used and available memory.
• Main Menu View—Select whether you want to view the main
@metro menu in a list or icon format.
• Screen Savers—View downloaded screensavers.
• View Log—View the @metro log, which displays information about recent activity using @metro.
3. Use the navigation keys to highlight an option.
4. Press to enter the option’s sub menu and to view or change @metro settings.
Section 7: @metro 81
Help
The Help menu within @metro lists short tutorials on several @metro features. View information about charges, cancelling subscriptions, buying apps, disabling apps, and more.
1. In standby mode, press the right navigation key ( @). The
@metro menu containing the following icons appears in the display:
@metro Access @metro catalog.
Settings View and change @metro settings.
Help View @metro tutorials.
The @metro icon ( ) is highlighted.
2. Use the navigation keys to highlight the Help icon ( ), then press .
The Help subjects listed in the following sections appear in the display.
Buying New Apps
To buy new and exciting applications (apps), visit the
@metro Shop. This feature provides you with a variety of applications you can choose from.
What do I pay?
If you buy an application you will be charged for the purchase cost of the application (app) and the network connections to download it. Charges will also apply when
82
Help you use apps that require network connections, such as downloading information and sending TXT messages.
Charges
Charges will apply for network connections. A network connection is used when you are browsing the @metro
Shop, downloading and restoring apps, or cancelling subscription apps. Charges will also apply when you use apps that require network connections, such as downloading information and sending TXT messages.
Cancelling Subscription
To cancel a subscription to an application, choose
Settings , then choose Manage Apps.
Select the application subscription you want to cancel.
Demo Apps
A Demo app is free and is designed to demonstrate the app’s main features. It usually expires after a certain period of time or number of uses and often has limited functions.
Removing Apps
Note: When you remove an app, you cannot use it unless you purchase it again. If you expect or want to use the app again in the future, disable the app instead of removing it.
You may remove apps that are no longer needed.
To remove an app, choose Settings, then choose Manage
Apps .
Select the app you want to remove.
Section 7: @metro 83
Disabled Apps
You can install new apps if the memory of your phone is full by partially removing (disabling) apps you haven’t used recently.
Note: When you need to use a disabled app, you can restore it at no additional purchase cost.
Restoring Apps
Disabled apps can be quickly restored at no additional purchase cost. To restore an app, run the application you want to restore from the Main Menu. You will be guided through the restoration process.
Expired Apps
An Expired App is an application purchased for a certain number of uses. To purchase additional uses visit the
@metro Shop.
84
Section 8: MyMetro
Topics Covered
• Monthly Bill
• MetroConnect
• MetroPCS Card
This section explains how you can use MyMetro on your
SCH-a570 phone to view and pay your monthly metroPCS bill(s) on-line or make other payment arrangements.
Section 8: MyMetro 85
Monthly Bill
The Monthly Bill option lets you review your monthly metroPCS bill.
1. In standby mode, press the Menu (left) soft key ( ), then press for MyMetro. The following MyMetro menu options appear in the display:
• Monthly Bill—View your current monthly bill.
• MetroConnect—View the current balance of your account.
• MetroPCS Card—View and pay the current balance of your account or make payment arrangements.
The Monthly Bill option is highlighted.
2. Press . Your current bill information appears in the display.
3. Use the navigation keys to scroll through the contents of your monthly bill.
MetroConnect
The MetroConnect option lets you review the current balance for your account.
1. In standby mode, press the Menu (left) soft key ( ), then press for MyMetro. The following MyMetro menu options appear in the display:
• Monthly Bill—View your current monthly bill.
• MetroConnect—View the current balance of your account.
• MetroPCS Card—View and pay the current balance of your account or make payment arrangements.
The Monthly Bill option is highlighted.
86
MetroPCS Card
2. Use the navigation keys to highlight the MetroConnect option.
3. Press . Your current account balance appears in the display.
MetroPCS Card
The MetroPCS Card sub menu contains options that let you review and pay the current balance for your account.
1. In standby mode, press the Menu (left) soft key ( ), then press for MyMetro. The following MyMetro menu options appear in the display:
• Monthly Bill—View your current monthly bill.
• MetroConnect—View the current balance of your account.
• MetroPCS Card—View and pay the current balance of your account or make payment arrangements.
The Monthly Bill option is highlighted.
2. Use the navigation keys to highlight the MetroPCS Card option.
3. Press . The following options appear in the display:
• Request Balance
• Pay Monthly Bill
The Request Balance option is highlighted.
Section 8: MyMetro 87
Request Balance
The Request Balance option lets you review the current balance of your account before making a payment.
â– At the MetroPCS Card menu, press the key to select the highlighted Request Balance option. Your current account balance appears in the display.
Pay Monthly Bill
The Pay Monthly Bill option lets you pay the current balance of your account on-line or make other payment arrangements.
1. At the MetroPCS Card menu, use the navigation keys to highlight the Pay Monthly Bill option.
2. Press . The following options appear in the display:
• Credit Card—Use a credit card other than your metroPCS card to pay your current account balance on-line.
• MetroPCS Card—Use your metroPCS card to pay your current account balance on-line.
• Other Options—Automatically call metroPCS to make other payment arrangements.
88
Section 9: Messaging
Topics Covered
• Creating and Sending New Messages
• Message Send Options
• Retrieving New Messages
• Voice Mail
• Message Folders
• Message Settings
• Deleting Messages
This section explains how to create, send, receive, and view different types of messages. This section also includes the features and functionality associated with messaging.
Section 9: Messaging 89
Creating and Sending New Messages
This section guides you through the procedure to create and send various types of messages.
Creating and Sending a Text (TXT) Message
1. In standby mode, press the Down navigation key, then
Or
Press the Menu (left) soft key ( ), then press (for
Messages) and for Send New Msg.
2. Enter the phone number of the recipient, then press the
key.
3. Enter the text for your message using the keypad. (See
“Section 5: Entering Text” on page 53 for more
information.)
4. At any point while composing a message, press the
Option (left) soft key ( ). The following options appear in the display:
䢇 ABC—The entry mode for your message. Other modes, which are hidden, are Symbol, 123, and T9 Word. Use the navigation keys to show each of the text entry modes.
䢇 Quick Text—Insert a pre-composed message into the body of your current message.
5. Once you’re finished entering your message, press the
key. The following New Message options appear in the display:
䢇 Edit Send To—Edit the recipient’s Send To number.
䢇 Edit Text—Edit the content of your message.
90
Message Send Options
䢇 Send Options—Choose the Priority, Privacy, Delivery
Acknowledgement, and whether you wish to Insert a Signature or Call Back # in the message.
䢇 Save in Draft—Save the message to your Draft folder.
䢇 Save Text—Save the text in your message as a Quick Text message. Quick Text messages are pre-composed messages that can be inserted into any message you choose.
6. To send your message, press the Send (left) soft key
( ).
Message Send Options
You can set priority, privacy, validity, and other options before you send a message.
1. After you’ve composed a message and pressed the key, you’re returned to the New Message menu.
2. Use the navigation keys to highlight Send Options, then press the key. The following Send Options appear in the display:
䢇 Priority—Assign a priority to your message.
䢇 Privacy—Lets you attach a privacy indicator (NotRestricted,
Restricted, or Confidential) to the message.
䢇 Delivery Ack—Lets you activate or deactivate the message delivery acknowledgement function. When this function is activated, the network informs you whether or not this message has been delivered.
䢇 Insert Sign.—Insert your pre-composed signature text into the message.
䢇 Call Back #—Insert a number into your message for the recipient to call you back.
Section 9: Messaging 91
3. Use the navigation keys to display the various Send
Options for each menu item.
4. When the desired send option is highlighted, press the
key to confirm the selection or to enter the send option’s sub-menu.
Retrieving New Messages
When you receive a message in standby mode, the ringer sounds (unless turned off) and New Message appears in the display along with the closed envelope icon ( ). The date and time of the message also appear in the display.
• Press the Ignore (left) soft key ( ) to return your phone to standby mode. The message is saved to your Inbox where you can view it later.
• Press the View (right) soft key ( ) to open the message, where you have the option to Reply, Forward, Erase, Save Text,
Save Msg, Save Contact, or Block sender.
Retrieve Messages While in a Call
When you receive a message while in a call, New
Message appears in the display along with the closed envelope icon ( ). To view the message without disconnecting the call:
• Press the Ignore (left) soft key ( ) to ignore the message and save it to your inbox where you can view it later.
• Press the View (right) soft key ( ) to open the message, your call remains connected.
92
Voice Mail
Voice Mail
Voice Mail allows callers to leave voice messages in your voice mailbox, and lets you review, play, and delete your voice messages any time you are in a network coverage area.
Voice Mail Setup
Before callers can leave voice mail messages, you must
first set up your account. See “Setting Up Your Voice
Mail” on page 13 for more information.
Check your Voice Mail
1. In standby mode, press and hold the key until you’re connected to the voice mail system. A recorded message prompts you for a password.
2. Enter your password, then press the key. Follow the recorded prompts, to listen to your voice message, change administrative options, and so on.
Section 9: Messaging 93
Message Folders
Voice Mail
New voice messages in your voice mailbox are logged in the Voice Mail folder of the Messages menu. Open the Voice Mail folder to view the Callback # (if available), Urgency, and other details of new voice mail messages.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Messages) and (for Voice
Mail). A Voice Mail status screen indicating the number of new messages in your voice mailbox, their urgency, and any callback numbers appears in the display.
2. Press the key to call your voice mailbox and listen to the message.
Note: You can also press and hold the key to dial your voice mailbox.
Inbox
Received messages of all types (except Voice Mail) are stored in the Inbox.
1. In standby mode, press the Down navigation key, then press Inbox) to open the Inbox folder,
Or
Press the Menu (left) soft key ( ), then press (for
Messages) and (for Inbox) to open the Inbox folder.
Tip: While in a call, press the MSG (right) soft key to open the
Messages menu.
94
Message Folders
2. Use the navigation keys to highlight an incoming message that you wish to view.
3. Press the key to view the highlighted message.
4. While viewing your message, press the Options (left) soft key ( ), The following options appear in the display:
䢇 Reply—Lets you reply to a message.
䢇 Forward—Lets you forward the message to other Email addresses or phone numbers.
䢇 Erase—Erases the selected message.
䢇 Save Text—Saves text in the message to Quick Text.
䢇 Save Msg—Save the message to the Saved message folder.
䢇 Save Contact—Save the sender’s number to your Contacts.
䢇 Block Sender—Block future messages from the sender.
5. Use the navigation keys to highlight an option. Press the
key to perform the function for the highlighted option.
Section 9: Messaging 95
Outbox
Your phone stores outgoing messages in the Outbox, regardless of whether the message was successfully transmitted to, or received by, the addressee.
Tip: Verify whether and when a message or e-mail was successfully received by enabling the Delivery Report feature.
1. In standby mode, press the Down navigation key, then
Or
Press the Menu (left) soft key ( ), then press (for
Messages) and (for Outbox).
A list of your outgoing messages appears in the display.
2. Use the navigation keys to highlight a message that you wish to review, the press the key.
3. Press the Option (left) soft key ( ). The following options appear in the display:
䢇 Re-send—Re-send the message.
䢇 Save Msg—Save the message to the Saved Msg folder.
䢇 Erase—Erase the message.
4. Use the navigation keys to highlight the desired option.
5. Press the key to perform the function for the highlighted option.
96
Message Folders
Draft Box
Messages in the Draft Box are those that have been composed but never sent. You can return to the Draft
Box at any time to view, edit, or send a draft message.
1. In standby mode, press the Down navigation key, then
Or
Press the Menu (left) soft key ( ), then press (for
Messages) and (for Draft Box).
A list of your draft messages appears in the display.
2. Use the navigation keys to highlight the message that you wish to view, the press the key.
3. Press the left soft key ( ) Options, to display the options listed.
䢇 Edit—Edit the message.
䢇 Erase—Erase the message.
4. Use the navigation keys to highlight the desired option.
5. Press the key to perform the function for the highlighted option.
Saved Box
Messages in the Save Msg folder are messages that have been saved.
1. In standby mode, press the Down navigation key, then
Or
Press the Menu (left) soft key ( ), then press (for
Messages) and (for Saved).
Any saved messages appear in the display.
Section 9: Messaging 97
2. Use the navigation keys to highlight the message you wish to view, the press the key.
3. Press the left soft key ( ) Option, to display the message options.
䢇 Edit—Edit the message.
䢇 Erase—Erase the message.
4. Use the navigation keys to highlight the desired option.
Press the key to perform the highlighted option.
Messages and Lock Mode
Your phone can still receive messages while in Lock
Mode. The time and date of the message appear in the display, but you cannot access the message until you
enter the lock code. (See “Lock Phone” on page 143 for
more information.)
Message Settings
The Msg Settings folder lets you define numerous message settings such as ringer types and save options.
1. In standby mode, press the Down navigation key, then press Msg Setting),
Or
Press the Menu (left) soft key ( ), then press (for
Messages) and (for Msg Setting).
The following Msg Setting options appear in the display:
䢇 Send Setting—Options to Save In Outbox, Callback #, Entry
Mode, Insert Sign., Delivery Ack.
䢇 Msg Alert—Set Volume/Vibrate, Ringer type, and Reminder.
98
Message Settings
䢇 Auto Play—Auto Play auto scrolls messages that are two pages or more.
䢇 Auto View—Select Auto View on/off.
䢇 Auto Erase—Automatically erase first message received after memory is full.
䢇 Block/Unblock—Block messages from a specified web address or phone number.
䢇 Quick Text—Insert a pre-composed message into the message.
䢇 Signature—Create a signature, which appears at the bottom of all outgoing messages.
2. Use the navigation keys to highlight the desired submenu. Press the key to enter the sub-menu and adjust the selected message settings.
Message Alerts
1. In standby mode, press the Down navigation key, then press Msg Setting) and for Msg Alert,
Or
Press the Menu (left) soft key ( ), then press (for
Messages),
Alert.
Msg Setting), and for Msg
The following sub-menus appear in the display:
䢇 Volume/Vibrate—Lets you set the default volume for message alerts.
䢇 Ringer Type—Lets you assign ringer types and melody tones for message alerts.
䢇 Reminder—Lets you set how often the message alert reminder sounds (Off, Once, or Every 2 min.)
Section 9: Messaging 99
2. Use the navigation keys to highlight the desired submenu, then press the key to enter the sub-menu and adjust settings.
Deleting Messages
You can erase all of the messages in each/all of your message folders from one convenient location.
Note: This function erases all messages in a selected message folder or in all message folders. To delete a single message, from the Messages menu, open the message folder where the message to be deleted is stored, then select and delete the message from the Option menu while viewing the message content.
1. In standby mode, press the Down navigation key, then
Or the Menu (left) soft key ( ) key, then press (for
Messages) and for Erase Msg.
The following options appear in the display:
䢇 Voice—Lets you delete all voice mail log entries from your
Voice Main folder.
䢇 Inbox—Lets you delete all messages from your Inbox.
䢇 Outbox—Lets you delete all messages from your Outbox.
䢇 Draft—Lets you delete all draft messages from the Draft folder.
䢇 Saved—Lets you delete all messages from the Saved folder.
䢇 All Messages—Lets you delete all messages from all message folders.
2. Use the navigation keys to highlight the folder containing the messages that you wish to delete.
100
Deleting Messages
3. Press the key to open the highlighted folder. You are prompted to confirm the erasure of all messages in the folder.
4. Use the navigation keys to highlight Yes or No, then press the key.
Section 9: Messaging 101
102
Section 10: Sounds
Topics Covered
• Volume/Vibrate
• Ringer Type
• Key Beep
• Alerts
• Power On/Off
• Roam Ringer
• Whisper Mode
This section explains how you can customize your phone’s ring tones, keypad tones, alerts, shut down sounds, and more.
Section 10: Sounds 103
Volume/Vibrate
Use the Volume/Vibrate menu to set the default volume for incoming calls and alarms, or to set your phone to vibrate mode.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Sounds) and for the Volume/
Vibrate sub menu.
2. Use the navigation keys to highlight Calls or Alarm, then press .
3. Use the up and down volume keys to select the volume level (1 – 5) or one of the following vibration modes for the selected option:
• Ringer off—No sound or vibration.
• 1 Beep—Plays a single beep without vibration.
• Vibrate—Phone Vibrates without sound.
• Vib+Ring—Phone Vibrates first, then follows with sound.
Ringer Type
The Ringer Type menu allows you to set a unique ring for voice calls, data, alarms, and Tools alerts. As you change a ringer type, it plays so you can preview it.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Sounds) and for the Ringer
Type sub menu.
The following ringer types appear in the display:
• Calls
104
Key Beep
• Alarm
• Data
• Calendar
2. Use the navigation key to highlight a ringer type, then press . A pop-up menu containing the following options appears in the display:
• Preloaded—Preview sounds included with your phone.
• My Melody—Preview sounds you have downloaded and saved.
A list of bells and melodies appears in the display, each playing as it is highlighted.
3. Use the navigation keys to browse through available ring tones.
4. When the desired ringer type plays, press to save the setting.
Key Beep
Use the Key Beep menu to adjust the tone volume and the type of tone that your keypad generates when you press a key.
Key Beep Volume
1. In standby mode, press the Menu (left) soft key ( ), then press (for Sounds) and for Key Beep.
The following Key Beep menu items appear in the display:
• Volume
• Tone Length
Section 10: Sounds 105
Volume is highlighted.
2. Press .
3. Use the volume keys or the navigation keys to set the volume level for keypad tones. A tone sounds as you increase or decrease the volume setting.
4. Press when the key beep volume setting you want displays. You’re returned to the Key Beep menu.
Key Beep Tone Length
1. While in the Key Beep menu, use the navigation keys to highlight Tone Length, then press .
2. Use the navigation keys to highlight Long or Normal.
3. Press to save your settings.
Alerts
You can set your phone to sound an alert whenever you enter or leave your service area, connect or disconnect a call, as well as other options.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Sounds) and for Alerts.
The following Alerts menu items appear in the display:
• Minute Beep—Sound an alert ten seconds before each elapsed minute of a call.
• Service—Sound an alert when you enter or leave your service provider’s coverage area.
• Connect—Sound an alert and/or produce a unique VibeTonz touch sensation when you answer a call.
106
Power On/Off
• Disconnect—Sound an alert and/or produce a distinctive
VibeTonz touch sensation when a call is dropped.
• Fade—Sound an alert when a call is dropped during a conversation.
• Roam—Sound an alert when you leave your home service area during a call.
• Privacy—Sound a tone whenever you are in enhanced privacy mode.
2. Use the navigation keys to highlight the alert setting you want to change, then press . A prompt containing On and Off options appears in the display.
3. Use the navigation keys to highlight Off or On.
4. Press to save your selection.
Power On/Off
Set your phone to play a sound and/or VibeTonz touch sensation whenever you turn the phone on or off.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Sounds) and for Power On/
Off. The following options appear in the display:
• On
• Off
2. Use the navigation keys to highlight the option you want, then press .
Section 10: Sounds 107
Roam Ringer
Set your phone to sound a unique tone when a call is received outside your home service area.
Note: By default, this feature is set to On.
1. In standby mode, press the Menu (left) soft key ( ), then press
Ringer.
(for Sounds) and for Roam
A prompt containing On and Off options appears in the display.
2. Use the navigation keys to highlight Off or On.
Whisper Mode
This feature lets you talk in a low volume during a phone conversation and still be heard by the other party.
1. In standby mode, press the Menu (left) soft key ( ), then press (Sounds) and for Whisper Mode.
2. Use the navigation keys to highlight On or Off, then press
.
108
Section 11: Tools
Topics Covered
• Tools
• Voice
• Today
• Calendar
• To Do List
• Alarm Clock
• Memo Pad
• Voice Memo
• World Time
• Calculator
• Count Down
This section explains how to use your phone’s digital assistant functionality to schedule events, set reminders, create a “to do” list, perform calculations, and more.
Section 11: Tools 109
Tools
Planner is a suite of Personal Digital Assistant (PDA) applications such as a Calendar, To Do List, and Memo
Pad that run on your phone. You can use your phone to schedule events, set reminders, create a to do list, perform calculations, and more with the functions provided by this useful feature.
Opening Tools
1. In standby mode, press the Menu (left) soft key ( ), then press for Tools. The following sub-menus appear in the display:
䢇 Voice—Lets you access voice commands and adapt voice recognition to your voice.
䢇 Today—Lets you review and schedule events that will occur today.
䢇 Calendar—Lets you view the current, past, or future month in a monthly calendar layout.
䢇 To Do List—Lets you create and maintain a task list.
䢇 Alarm Clock—Lets you set an alarm to go off once, or daily, at a specified time.
䢇 Memo Pad—Lets you store and review useful information.
䢇 World Time—Lets you view the current time of day or night in another part of the world.
䢇 Calculator—Lets you perform calculations, including addition, subtraction, multiplication, and division.
䢇 Count Down—Lets you view the amount of time between the current date and any event that you want to schedule.
2. Use the navigation keys to highlight an application, then press the key to enter the application’s sub-menu.
110
Tools
The following sections provide detailed descriptions of the applications and how to use their functions.
Tip: You can also set the Down navigation key as a shortcut to launch one of the following PDA applications:
• Today
• Calendar
• To Do List
• Alarm Clock
• Memo Pad
• Calculator
• Voice Memo
See “Shortcut” on page 159 for more information.
Section 11: Tools 111
Voice
Voice Signal is state-of-the-art voice recognition software for your mobile phone that lets you dial numbers, lookup contact information, and open applications using your voice.
VoiceSignal Commands
VoiceSignal includes the following commands:
• Voice Dial—Lets you dial the phone by saying any name stored in your contact list, without ever having to record, or “train” that name. VoiceSignal automatically voice-activates all your contacts, even if you have hundreds of them stored on your phone. You can also dial any telephone number, even if it is not stored in your contact list, by saying the digits in the number.
(See “Making a Call—Voice Dialing” on page 26 for more
information.)
• Voice Memo—Lets you access the voice memo feature of your
phone. (See “Voice Memo” on page 114 for more information.)
• Today—Lets you access the Today feature of your phone. (See
“Today” on page 122 for more information.)
• Calendar—Lets you access the Calendar feature of your
phone. (See “Calendar” on page 124 for more information.)
• Contacts—Lets you look up and display contact information for any name stored in your Contacts list by saying the name. (See
“Finding a Contacts Entry” on page 66 for more information.)
• Status—Lets you say a single command (“Status”) to check your phone's network coverage, signal strength, and battery.
Voice-Activating Your Contacts List
When you first start VoiceSignal, it reads your Contacts list and voice-activates all the names stored there.
When you have add or change contacts, VoiceSignal automatically reloads and voice-activates the entire list.
112
Voice
Ending Calls Before Restarting the VoiceSignal Software
When you use VoiceSignal to make a call, you must end that call before you can use VoiceSignal again.
Starting VoiceSignal
To start VoiceSignal, press and hold the key for about a second, and then release the key.
Note: You can also set your phone to start VoiceSignal when you open the
phone. See “Voice Launch” on page 121 for more information.
To change the way you launch VoiceSignal:
1. In standby mode, press and hold the key to launch
VoiceSignal.
“Say a Command” appears in the display and is pronounced through the speaker.
2. Press the left soft key to select Settings, and then press
for Voice Launch to select how you want to launch
VoiceSignal.
When you start VoiceSignal, it displays its main menu of voice commands and prompts you to “Say a command.”
Note: Speaking clearly, say the command that you want to use. If, after a few seconds, the device has not recognized a command, it prompts you to repeat the command. If, after a few more seconds, it still has not recognized a command, it tells you “Sorry, no match found,” and cancels voice recognition.
Voice Command Tips:
• Make sure you wait for the beep before speaking
• Speak clearly at a normal volume, as if you were talking on the phone.
Section 11: Tools 113
Voice Memo
You can use your phone to record voice memos for later playback. You can also record the caller on the other end of the line during a phone conversation.
Note: There is limited space for the number and length of recordings.
• The maximum number of voice memos is 10.
• The maximum length for a single voice memo is 60 seconds.
Record a Voice Memo
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools),
Voice Memo), and for Record. The phone prompts,
“Please record after the beep.”
Tip: To launch Voice Memo using a voice command—In standby mode, press and hold until the phone prompts, “ Say a command.
” Say
“ Voice Memo ” into the microphone.
2. Wait for the beep, then start speaking. As it is recording the phone displays a countdown timer that shows the seconds remaining for the recording.
䢇 To pause the memo, press the Pause (left) soft key ( ).
When a memo is paused, select Resume to resume recording.
3. Press the Stop (right) soft key ( ) once you’re finished recording. The Memo Review screen appears in the display with the new recording highlighted.
4. To review the new recording, press the Play (right) soft key ( ).
114
Voice
5. For other voice memo options, press the Option (left) soft key ( ). The following options appear in the display:
䢇 Erase—Deletes the selected voice memo.
䢇 Erase All—Deletes all voice memos.
䢇 Edit Caption—Lets you change or replace the name of the selected voice memo.
䢇 Info—Shows the Memo Title, Length and Size, and Recorded at date and time for the selected voice memo.
6. Use the navigation keys to highlight an option. Press the
key to perform the function for that option.
7. To save the voice memo, select Save from the pop-up menu, then press the key.
8. Enter a name for the voice memo using the keypad.
9. Press the key to save the voice memo.
Review and Erase Voice Memos
If you’ve saved any voice memos, you can review them anytime.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools), Voice),
Voice Memo), and for Review. A list of saved voice memos appears in the display.
2. Use the navigation keys to highlight the voice memo you wish to review, and press the key. Information about the voice memo appears in the display.
3. Press the Play (right) soft key ( ) to play the voice memo.
4. Press the Option (left) soft key ( ) to show the Erase,
Erase All, Edit Caption, and Info options.
Section 11: Tools 115
Erase All Voice Memos at One Time
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools), Voice),
Voice Memo), and for Erase All. “Erase all Voice
Memos?” appears in the display.
2. Use the navigation keys to highlight Yes (to erase all memos) or No (to return to the previous menu).
3. Press the key to confirm your selection.
Adapting Digits
If you regularly have trouble getting VoiceSignal to recognize the numbers you say, try adapting digit dialing to your voice. Adapting can improve the accuracy of digit recognition, especially for people with strong regional accents.
Adaptation involves recording several sequences of four digits each. The recording process takes about a minute.
Tips for Adapting Digit dialing:
• Adapt digits in a quiet place.
• Make sure you wait for the beep before starting to speak.
• Speak clearly, and say each digit distinctly.
• If you make a mistake while recording a sequence of digits, or if there is an unexpected noise that spoils the recording, rerecord that sequence.
• Only adapt digits if you are regularly having problems with digit dialing. Once you adapt, digit dialing will not work as well for other people using your phone. (You can always reset digit adaptation to its original state, as described below.)
116
Voice
Voice Command Method
To adapt digit dialing:
1. In standby mode, press and hold the key to launch
VoiceSignal.
“Say a Command” appears in the display and is pronounced through the speaker.
2. Press the Settings (left) soft key ( ), then press
(for Digit Dialing) and for Adapt Digits.
3. Follow the instructions on the display.
To reset digit adaptation:
1. In standby mode, press and hold the key to launch
VoiceSignal.
“Say a Command” appears in the display and is pronounced through the speaker.
2. Press the Settings (left) soft key ( ), then press
(for Digit Dialing) and for Reset Digits.
Voice Setting Menu Method
To adapt digit dialing:
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools),
Voice Setting), Digit Dialing), and for
Adapt Digits. A description of the Adapt Digits process appears in the display.
2. Press the OK (left) soft key ( ) to begin the process.
3. Follow the instructions played through the earpiece and shown on the display.
Section 11: Tools 117
To reset digit adaptation:
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools),
Voice Setting), Digit Dialing), and for
Reset Digits.
Choice Lists Settings
VoiceSignal uses choice lists when it is not confident it has correctly recognized a name or number. In this case, it can display a list of up to three possible choices, and prompt you to confirm the correct one.
You can change the way that VoiceSignal uses choice lists with name dialing, digit dialing, and contacts. For each feature, you can choose to always see a choice list
(even if there is only one choice), or never see a choice list (even if there are multiple choices). If you leave the setting at “Automatic,” VoiceSignal displays a choice list only when it is not confident it has correctly recognized the name or number.
Voice Command Method
To change the way VoiceSignal uses choice lists:
1. In standby mode, press and hold the key to launch
VoiceSignal.
“Say a Command” appears in the display and is pronounced through the speaker.
2. Press Settings, and then select Choice Lists.
3. Select Name Dialing, Digit Dialing, or Contacts.
118
Voice
4. Click the radio button for the choice list behavior you want:
䢇 Automatic—VoiceSignal displays a choice list only when it is not sure if it has correctly recognized the name or number.
䢇 Always On—VoiceSignal always displays a choice list, even when there is only one choice.
䢇 Always Off—VoiceSignal never displays a choice list.
5. Press to accept the new setting.
Voice Setting Menu Method
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools), Voice),
Voice Setting), and for Choice Lists.
2. Select Name Dialing, Digit Dialing, or Contacts.
3. Click the radio button for the choice list behavior you want:
䢇 Automatic—VoiceSignal displays a choice list only when it is not sure if it has correctly recognized the name or number.
䢇 Always On—VoiceSignal always displays a choice list, even when there is only one choice.
䢇 Always Off—VoiceSignal never displays a choice list.
4. Press the OK (left) soft key ( ) to accept the new setting.
Section 11: Tools 119
Text-To-Speech (TTS)
TTS lets you enable audio playback of Main Menu names and 1st level sub-menu option/menu labels.
1. In standby mode, press the Menu (left) soft key ( ), then press Voice), and for
TTS. The following options appear in the display:
䢇 TTS On — Enables audio playback of menu/sub-menu labels.
䢇 TTS Off — Disables audio playback of menu/sub-menu labels.
2. Use the navigation keys to highlight the desired setting.
3. Press the key to accept the new setting.
Voice Settings
Sound
Sound lets you specify what (if any) text prompts you want your phone to read to you through the earpiece.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools),
Voice Setting), and for Sound. The following options appear in the display:
䢇 Prompts — Enables or disables audio prompts.
䢇 Digits — Enables or disables audio digit playback.
䢇 Names — Enables or disables audio name playback.
䢇 Name Settings — Lets you adjust the speed and volume of your phone’s audio name playback.
2. Use the navigation keys to highlight the desired setting.
3. Press the OK (left) soft key ( ) to accept the new setting.
120
Voice
Voice Launch
Voice Launch lets you select the action you wish to take to launch VoiceSignal.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools), Voice),
Voice Setting), and for Voice Launch. The following options appear in the display:
䢇 Zero Only? — Only pressing and holding launches
VoiceSignal.
䢇 Zero or Flip? — Pressing and holding or opening folder launches VoiceSignal.
䢇 Zero or EarMic? — Pressing and holding or plugging a headset into the headset jack launches VoiceSignal.
2. Use the navigation keys to highlight the desired setting.
3. Press the OK (left) soft key ( ) to accept the new setting.
About
This option causes the About VoiceSignal screen to appear in the display, showing version and build information about the VoiceSignal software included on your phone.
Section 11: Tools 121
Today
Today lets you schedule up to nine events for the current day by indicating each event’s start time and advance notification time. You can set alarms for these events so that you can be alerted before each event takes place.
Events, previously created for the present day using your phone’s Calendar, automatically appear in your
Today events list. (See “Calendar” on page 124 for more
information.)
Add a New Event
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for Today.
Tip: To launch Today using a voice command—In standby mode, press and hold until the phone prompts, “ Say a command.
” Say “ Today ” into the microphone.
You’re prompted to enter a New Event.
2. Enter details of the event using the keypad. (See
“Section 5: Entering Text” on page 53 for more
information.)
3. Press the Option (left) soft key ( ). A pop-up menu appears in the display containing the following text entry mode options:
䢇 T9 Word
䢇 ABC
䢇 Symbol
䢇 123
122
Today
Note: The current mode of text entry is indicated in the lower right of the
display. See “Text Entry Modes” on page 54 for more information on text
entry modes.
4. Use the navigation keys to highlight the entry mode that you wish to use and press the key, or press the key to exit the pop-up menu.
5. When you’re finished entering details for the event, press the key. You’re prompted to enter the time and date for the event.
6. Use the Left and Right navigation keys to change between AM or PM.
7. Enter the time and date for the event using the keypad.
8. When you’re finished entering the time and date, use the navigation keys to highlight Alarm Option field.
9. Use the navigation keys to select the amount of time before the event occurs that you wish to be notified by an alert.
10. Press the key to store the event in your calendar. An alert will notify you prior to the event, if you set a notification alert.
Section 11: Tools 123
Calendar
Calendar lets you view the current, past, or future month in a monthly calendar layout. While viewing the calendar, the current date is highlighted and days with scheduled events are surrounded by a box.
View an event
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for Calendar.
Tip: To launch Calendar using a voice command—In standby mode, press and hold until the phone prompts, “ Say a command.
” Say
“ Calendar ” into the microphone.
A calendar appears in the display with the current date highlighted. The month and year also appear.
2. Use the navigation keys to move around within the calendar.
• Press the to open the highlighted date.
• Press the volume up key ( ) to view previous months.
•
Press the volume down key ( ) to view future months.
• Press the Option (left) soft key ( ) while viewing the calendar to display the following options.
䢇 View—View events for any date surrounded by a box.
䢇 Add new—Add a new event for the date.
䢇 Jump to date—Lets you jump to any date you specify.
124
To-Do List
To-Do List
The To Do List lets you create a task list. You can store, prioritize and manage up to twenty To Do List tasks.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for To Do List. The
Add To Do screen appears in the display.
2. Enter details of the task using the keypad. (See “Section
5: Entering Text” on page 53 for more information.)
3. Press the left soft key ( ) Option to display a pop-up menu containing the following text entry mode options.
䢇 T9 Word
䢇 ABC
䢇 Symbol
䢇 123
4. Use the navigation keys to highlight the entry mode that you wish to use and press the key, or press to exit the pop-up menu.
5. When you’re finished entering details for the task, press the key. You’re prompted to enter the priority for the task.
6. Use the navigation keys to select High or Low.
7. Use the navigation keys to highlight the Time field.
Use the navigation keys to select PM or AM.
8. Enter a time and date for the task using the keypad.
9. Press the key to store the task.
Section 11: Tools 125
Add, Edit, and Erase To-Do List Tasks
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for To Do List.
2. Use the navigation keys to browse tasks in your To Do
List. Events are presented in order of priority.
3. Press the Option (left) soft key ( ) while viewing your
To Do List. A pop-up menu containing the following options appears in the display:
䢇 Add new—Add new task to the To Do List.
䢇 Edit—Edit the task currently appearing in the display.
䢇 Erase—Erase the task currently appearing in the display.
䢇 Erase All—Erase all tasks from your To Do List.
4. Use the navigation keys to highlight an option.
5. Press the key to perform the function for the highlighted option.
126
Alarm Clock
Alarm Clock
Your phone has an alarm clock that can be set to go off once, or daily at a specified time. Once set, the alarm clock is easy to change or turn off completely.
Note: The alarm doesn’t function when the phone is turned off. If the time for an alarm that was set for Once has elapsed and the phone is off, the alarm occurs at the same time on the following day.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for Alarm Clock.
The following options appear in the display:
䢇 Alarm Clock 1
䢇 Alarm Clock 2
䢇 Alarm Clock 3
2. Use the navigation keys to highlight Alarm selection, then press the key.
3. Enter the time for the alarm using the keypad.
4. Press the key when you’re finished entering the time for the alarm. The alarm is set and the alarm icon ( ) appears in the top of the display.
Section 11: Tools 127
When an Alarm Sounds
An animated alarm clock appears in the display and an alert sounds when the specified time for the alarm arrives.
â– Press the key to silence the alarm.
䢇 If the alarm was set as a Once only alarm, the alarm icon disappears from the top of the display.
䢇 If the alarm was set as a Daily alarm, the alarm icon remains in the top of the display.
䢇 If the alarm was as a Mon-Fri, the alarm icon remains in the top of the display.
䢇 If the alarm was as a Mon-Sat, the alarm icon remains in the top of the display.
䢇 If the alarm was set as a Every Sun only alarm, the alarm icon disappears from the top of the display.
䢇 If the alarm was set as a Every Sat only alarm, the alarm icon disappears from the top of the display.
䢇 If the alarm was set as a Every Weekend only alarm, the alarm icon disappears from the top of the display.
Turn Off the Alarm
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for Alarm Clock.
The following options appear in the display.
䢇 Alarm Clock 1
䢇 Alarm Clock 2
䢇 Alarm Clock 3
2. Use the navigation keys to highlight Alarm selection, then press the key.
128
Memo Pad
3. Alarm is highlighted, use the navigation keys to select
Off, then press the key. Select alarm is turned off.
Memo Pad
You can create a notes and store them in Memo Pad.
You can’t prioritize or set an alert for stored notes.
Return to Memo Pad anytime you wish to review and edit your notes.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for Memo Pad.
2. If you have any stored memos, they appear as a list in the display. If this is your first time in Memo Pad, you’re prompted to add a new memo.
3. Enter a memo using the keypad. (See “Section 5:
Entering Text” on page 53 for more information.)
4. Press the Option (left) soft key ( ). A pop-up menu containing the following text entry mode options appears in the display:
䢇 T9 Word
䢇 ABC
䢇 Symbol
䢇 123
5. Use the navigation keys to highlight the entry mode that you wish to use and press the key, or press to exit the pop-up menu.
6. When you’re finished entering details for the memo, press the key. The memo is stored.
Section 11: Tools 129
Review, Add, Edit, and Erase Memos
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for Memo Pad. Your list of stored memos appears in the display.
2. Use the navigation keys to browse memos. Press the key to open a highlighted memo.
3. Press the Option (left) soft key ( ) while viewing your memos. A pop-up menu with the options listed in the following table appears in the display:
䢇 Add new—Add a new memo to Memo Pad.
䢇 Edit—Edit the memo currently highlighted or appearing in the display.
䢇 Erase—Erase the memo currently highlighted or appearing in the display.
䢇 Erase All—Erase all memos from Memo Pad.
4. Use the navigation keys to highlight an option.
5. Press the key to perform the function for the highlighted option.
World Time
World Time lets you view the time of day or night in another part of the world. World Time displays time in the 24 different time zones around the world.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for World Time. A world map appears in the display.
130
Calculator
2. Use the navigation keys to display the city and time that you wish to view. The following cities/time zones are supported:
• Alaska • San
Francisco
• New York
• Denver/
Arizona
• Caracas • Chicago/
Mexico
• Brasilia • Mid Atlantic
•
•
•
London
Moscow
Alma-ata
• Seoul/
Tokyo
• Wellington
•
•
Paris/Berlin
Abu Dhabi
• Bangkok/
Jakarta
• Guam/
Sydney
• Samoa/
Midway
• Cape
Verde
• Athens/
Helsinki
• Tashkent
• Hongkong/
Beijing
• Okhotsk
• Honolulu,
Hawaii
Calculator
You can perform calculations, including addition, subtraction, multiplication, and division using your phone.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Tools) and for Calculator. The
Calculator appears in the display.
2. Enter the first number in your equation using the keypad
(numbers can be up to nine digits long).
Press to enter a decimal point.
Section 11: Tools 131
Press to change the sign for a number to a negative.
3. Use the navigation keys to set the type of calculation that you wish to perform. Your choices are as follows:
䢇 [+] Addition
䢇 [-] Subtraction
䢇 [x] Multiplication
䢇 [÷] Division
4. Use the keypad to enter the second number into your equation.
5. Press the key to perform the calculation and view the result.
Count Down
Count Down lets you view the amount of time between the current date and any event that you wish to schedule. You can create up to twenty Count Down events.
1. In standby by mode press the Menu (left) soft key ( ), then press (for Tools) and for Count Down.
Note: If you have multiple Count Down timers, the event that is scheduled closest to the current date appears in the display. Use the navigation keys to browse the other Count Down timers.
2. Enter details for the Count Down event using the
keypad. (See “Section 5: Entering Text” on page 53 for
more information.)
132
Count Down
3. Press the Option (left) soft key ( ) to display a pop-up menu containing the following text entry mode options:
䢇 T9 Word
䢇 ABC
䢇 Symbol
䢇 123
4. Use the navigation key to highlight the entry mode that you wish to use, or press to exit the pop-up menu.
5. Once you’ve finished entering details for the Count Down event, press . You’re prompted to enter a time and date for the scheduled event.
6. Use the Left or Right navigation keys for AM or PM, respectively.
Enter the time and date using the keypad.
7. Press to store the event.
Review, Add, Edit, and Erase Count Down Events
Review scheduled Count Down event to determine how much time remains between the current time/date and any event that you’ve scheduled. You can also add another event, or edit and erase previously scheduled events.
1. In standby by mode press the Menu (left) soft key ( ), then press (for Tools) and for Count Down.
2. Any stored Count Down events appear in the display.
The event scheduled closest to the current date appears first in the display.
Section 11: Tools 133
134
Event details, including the days, hours and minutes left until the occurrence of the scheduled event appear in the display. The day, date, and time of the scheduled event appear in the bottom of the display.
3. Press the Option (left) soft key ( ), while viewing your memos. A pop-up menu displays with the options listed.
䢇 Add new—Add anew event to Count Down.
䢇 Edit—Edit the event currently appearing in the display.
䢇 Erase—Erase the event currently appearing in the display.
䢇 Erase All—Erase all scheduled event from Count Down.
4. Use the navigation keys to highlight an option.
5. Press to perform the function for the highlighted option.
Section 12: Mobile Web
Topics Covered
• Mobile Web
• Launching Mobile Web
• Using Mobile Web
• Using Links
• How Mobile Web Keys Work
This section outlines how to launch Mobile Web, how to navigate to other pages on the web, and how the keys on the keypad are used with the web application. Additionally, links to other sites are briefly discussed.
Section 12: Mobile Web 135
Mobile Web
With Mobile Web, you can conveniently surf the web using your phone. Each time you launch Mobile Web, your phone connects to the Internet and the service indicator icon ( ) appears in the display.
Stored web content
Mobile Web ends an Internet connection after a certain period of inactivity, however some information from your session remains stored in the phone (if you leave your phone turned on). You can access this information without reconnecting to the Internet. However, if you are viewing stored information, and you select a link to a site that was not accessed in your last session, you automatically re-connect to the Internet.
Launching Mobile Web
The first time you use Mobile Web, you are prompted to go through a setup process that takes approximately three to five minutes.
1. In standby mode, press the Left navigation key. If this is the initial launch of Mobile Web, you’re prompted to enable security before proceeding.
2. Press the left soft key ( ) Yes to proceed.
3. A list of categories (each representing one or more web sites) appears in the display.
4. Use the navigation keys to browse the categories.
136
Using Mobile Web
5. Once the desired category is highlighted, press the left soft key ( ) to enter the category list.
Exit Mobile Web
Press to exit Mobile Web.
Using Mobile Web
When you use Mobile Web, some of the keys operate differently than during a normal phone call. Mobile
Web presents on-screen items in any of the following ways:
• Text or numeric input.
• Links (embedded in content).
• Numbered options (some may not be numbered).
• Simple text.
You can act upon options or links by using the soft keys.
Mobile Web soft keys
the bottom of the Mobile Web display is a bar that contains browser commands. The left and right ( soft keys on the keypad are used to execute the command that appears above them in the display.
These are called “soft keys” because their function changes depending on the application.
)
Section 12: Mobile Web 137
Place a call while using Mobile Web
You may place a phone call from Mobile Web if the site you are using supports this feature (the phone number may be highlighted and the left soft key ( ) is labeled
Call). Press the left soft key ( ) Call to call the number.
The Internet connection terminates when you initiate the call. After you end the call, your phone returns to standby mode.
Using Links
Links have several purposes, such as jumping to a different page, to a different site, or even initiating a phone call. Links are shown inside of brackets ([ ]).
You can normally use the left soft key ( ) to select a link when it is highlighted.
How Mobile Web Keys Work
The following table lists Mobile Web keys and their functions.
Navigation keys—Use to browse lists and options
CLR Key—A browse, back-up key. Press once to back up one page. Press and hold to go back to the Mobile
Web home page.
Press to clear the last number, letter, or symbol entered.
Press and hold to completely clear the display.
138
How Mobile Web Keys Work
Asterisk/Shift Key—Press before entering text to enable uppercase characters.
Next Key—Press to enter a zero (0), or to display another word in the dictionary when in T9 Word entry mode.
Pound/Space Key—Press to insert a space when entering text.
Numbers 1 through 9—Use the number keys to select items in a menu if they are numbered.
End Key—Press to exit the Mobile Web and return the phone to standby mode.
Left Soft Key—Press to activate the command that appears above it in the display.
Right Soft Key—Press to activate the command that appears above it in the display.
Section 12: Mobile Web 139
140
Section 13: Set Up
Topics Covered
• Location Setting
• Network Selection
• Security Settings
• Display Settings
• Ringer Settings
• Call Options
• Shortcut
• Language
• Clock Set
• Version
This section explains how to customize your phone to suit your needs and preferences.
Section 13: Set Up 141
Location Setting
This function identifies your location to the network via the Global Positioning System (GPS). You can set this function for continuous operation or to operate only in the event that you dial 911.
Note: Contact your Wireless Provider to determine whether, when, or where location-based services are available.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Location.
The following options appear in the display:
䢇 Location On—GPS location setting is on wherever the feature is available.
䢇 911 Only—GPS location setting is on only when you dial 911.
2. Use the navigation keys to highlight the option you want.
3. Press the key to select the desired Location setting.
You’re returned to the Setup menu.
Network Selection
The Network setting lets you select NAM settings, and
Roam Options .
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Network. The following sub-menus appear in the display:
䢇
Set NAM —If your service contract has two phone lines, set the NAM option to NAM 2 to use both lines. Set the NAM option to NAM 1 otherwise.
142
Security Settings
䢇 Roam Option —Set your phone’s roaming options to Home
Only or Automatic.
2. Use the navigation keys to highlight the desired submenu, then press the key.
3. Use the navigation keys and press the key to highlight and select from available options.
Security Settings
Use the Security menu to lock your phone, set up emergency numbers, enable or disable voice privacy, set restrictions, as well as other security options.
Lock Phone
Locking the phone limits all outgoing calls except calls to 911 emergency and the five user-programmable emergency numbers. You can lock the phone manually during use, or set the phone to lock automatically when it is turned on. With the phone in lock mode, you can answer incoming calls, but you must unlock the phone to place outgoing calls (except to emergency and secret numbers).
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Security.
You’re prompted to enter the lock code. The default lock code is the last four digits of your telephone number.
Section 13: Set Up 143
in appear in the display.
䢇 Never—The phone remains unlocked.
䢇 On power up—The phone locks automatically the next time your phone is powered ON and stays locked until you enter the lock code.
䢇 Now—The phone locks immediately and stays locked until you enter the locked code.
3. Use the navigation keys to highlight the Lock Phone option of your choice.
4. Press to perform the function for the highlighted option.
Change Lock
The default lock code for your phone is generally the last four digits of your phone number. It is advisable to change the default lock code to a secret code for security purposes.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Security.
You’re prompted to enter the lock code. The default lock code is the last four digits of your telephone number. the new lock code.
3. Enter the new lock code. You’re prompted to re-enter the new lock code for verification.
4. Enter the new lock code again. Your changes are stored.
144
Security Settings
Note: Your phone does not allow you to view the lock code for obvious security reasons. If you change the lock code, be sure to write down or memorize the new code.
Emergency #
Your phone provides the option of storing five emergency numbers. Each number can be up to 20 digits in length. All emergency numbers can be manually called at any time, even when your phone is locked or restricted. This can be a useful feature for controlling outgoing calls from your phone.
Note: Emergency number911 is hard-coded into your phone. You can dial this number any time, even when the phone is locked or restricted. If you call 911 an audible tone is heard and an Emergency prompt appears in the display for the duration of the call.
Important: Because of various transmission methods, network parameters, and user settings necessary to complete a call from your wireless phone, a connection cannot always be guaranteed. Therefore, emergency calling may not be available on all wireless networks at all times.
Important: DO NOT depend on this phone as a primary method of calling911 or for any other essential or emergency communications.
Remember to always turn your phone on and check for adequate signal strength before placing a call.
Section 13: Set Up 145
Store Emergency Numbers
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Security.
You’re prompted to enter the lock code. The default lock code is the last four digits of your telephone number.
2. Enter the lock code, then press for Emergency #.
3. Press , , the five entry openings.
, , or to select from
4. Enter the emergency number (up to 20 digits in length).
5. Press to save the number that you entered.
Call Emergency Numbers in Lock Mode
1. In standby mode, enter the emergency number via the keypad.
2. Press to place the call.
Voice Privacy
Voice privacy lets you prevent those you call from seeing your number in their display when receiving your call. Voice privacy options are Standard and
Enhanced.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Security.
You’re prompted to enter the lock code. The default lock code is the last four digits of your telephone number. listed appear in the display.
䢇 Standard—Voice privacy is disabled.
䢇 Enhanced—Voice privacy is enabled.
146
Security Settings
3. Use the navigation keys to highlight the Voice Privacy option of your choice, then press .
Restriction
Restriction lets you restrict the use of your phone for outgoing calls, incoming calls, and calls placed from your Contacts.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Security.
You’re prompted to enter the lock code. The default lock code is the last four digits of your telephone number.
3. Use the navigation keys to select Outgoing Call,
Incoming Call, or Contacts.
4. Press .
5. Use the navigation keys to highlight On, Off, or Contacts then press .
Erase Memory
Erase memory erases your Contacts. This feature is useful if you want to give your phone to a friend or family member.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Security.
You’re prompted to enter the lock code. The default lock code is the last four digits of your telephone number. appears in the display.
Section 13: Set Up 147
3. Use the navigation keys to highlight Yes or No, then press . A confirmation message appears in the display while your messages are being erased. Your phone then returns to the Security menu.
Resetting Your Phone
Reset Phone returns all setup options to their factory default.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Security.
You’re prompted to enter the lock code. The default lock code is the last four digits of your telephone number. display asking if you wish to restore default settings
(except for the Contacts and Voice Dial).
3. Use the navigation keys to highlight Yes or No, then press .
Display Settings
Using the Display menu, you can set the menu style, set the standby mode animation, customize the backlight settings, and more.
1. In standby mode, press the Menu (left) soft key ( ), then press Display. The following Display sub-menus appear in the display:
䢇 Menu Style—Allow you to choose the main menu style.
䢇 Animation—Choose the media that displays on your phone when you turn it on, turn it off, and while in standby mode.
148
Display Settings
䢇 Banner—Create your own personalized greeting that appears in the display when your phone is in standby mode.
䢇 Backlight—Set backlight options for the LCD and keypad.
䢇 Contrast—Set display contrast.
䢇 Auto Hyphen—With Auto Hyphen enabled, your phone automatically hyphenates phone numbers as they are entered.
䢇 Dial Digits—Choose how the number will display on the display screen.
䢇 Dial Screen—Adjust the color of the display.
䢇 Service LED—Turn the service LED on or off.
2. Use the navigation keys to highlight a sub-menu.
3. Press the key to enter the highlighted sub-menu.
The following sections describe the above listed display sub-menus in greater detail.
Menu Style
This sub-menu lets you select the Main menu display style. You can choose either Icon or Text.
Animation
Animation lets you choose the multi-media or pictures that appear in your phone’s display when you turn it on, turn it off, and while in standby mode (wallpaper).
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up), Display) and
for Animation. The following options appear in the display:
䢇 Opening—Choose the animation that appears in your display when you turn on your phone.
䢇 Closing—Choose the animation that appears in you display when you turn off your phone.
Section 13: Set Up 149
䢇 Wallpaper—Choose the graphic or animation that appears in your display when the phone is in standby mode.
2. Use the navigation keys to highlight the sub-menu that you wish to enter, then press the key.
3. Use the navigation keys to select Preloaded or My
Image, then press the key.
4. Use the navigation keys to browse available images and animations for the selected sub-menu.
5. Press the key to select the image or animation appearing in the display.
Banner
Create your own personalized greeting that appears in the display while your phone is in standby mode.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up), Display) and
for Banner.
Note: Press and hold to erase an existing banner, if necessary.
2. Enter a word or short phrase to appear in your phone’s display while in standby mode (Up to 12 characters).
3. Press the key to save the new banner.
Backlight
You can set the backlight for your display or keypad to remain on for a specified period of time or remain on as long as the folder is open.
Note: Prolonged backlight use drains your battery faster.
150
Display Settings
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up), Display) and
for Backlight. The following sub-menus appear in the display:
䢇 LCD—Sets the amount of time the backlight for the LCD remains on after a period of inactivity. Optional settings are 5,
10, and 15 seconds as well as Folder Open.
䢇 Keypad—Sets the amount of time the backlight for the keypad remains on after a period inactivity. Optional settings are 5, 10, and 15 seconds as well as Folder Open.
䢇 Power save—Unless the backlight setting for the LCD has been changed, the backlight dims after a minute of inactivity, and then turns off. With Power save enabled, the backlight for the LCD is always dim. After 1 minute of inactivity, Power save turns the backlight off.
2. Use the navigation keys to highlight a sub-menu.
3. Press the key to enter the highlighted option’s submenu and change settings as desired.
Contrast
Set the display contrast to your preference.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up), Display) and
for Contrast.
(for Front LCD).
3. Use the navigation left/right keys to adjust the contrast for the display to your preference.
Section 13: Set Up 151
Auto Hyphen
Auto Hyphen automatically hyphenates phone numbers as they are entered. For example: 580-437-0000.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up), Display), and
for Auto Hyphen. On and Off appear in the display.
2. Use the navigation keys to highlight the desired setting.
3. Press the key to confirm the setting.
Dial Digits
Dial Digits adjust the color of numbers as they are entered into the display when making a call.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up), Display), and
for Dial Digits. The following option appear in the display.
䢇 Hyphenated—Number sections divided by hyphens (Area
Code, Exchange Number, or Directory Number) appear in different colors.
Note: The Auto Hyphen option must be set to On before you can select this option.
䢇 Rainbow—Each digit appears in a different color.
䢇 Basic—All digits appear in black.
2. Use the navigation keys to highlight the desired setting.
3. Press the key to confirm the setting.
152
Display Settings
Dial Screen
This option lets you select the background color of the
Dial Screen.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up), Display) and
for Dial Screen. The following options appear in the display:
䢇 Color Setting—Lets you select a background color.
䢇 Off—Deactivates Dial Screen, resetting the Dial Screen background color to white.
2. Use the navigation keys to highlight the desired setting.
3. Press the key to confirm the setting.
Service LED
The Service LED, located on the front of your phone
serves the following functions. See “Closed View of
• Flashes red to indicate an incoming call or message
• Flashes green briefly when your phone is in service.
• Lights red when you power the phone on.
• Lights red continuously when travel adapter is connected.
• Lights green continuously when travel adapter is connected and phone is fully charged.
Turn the Service LED on or off
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up), Display) and
for Service LED. Off and On appear in the display.
2. Use the navigation keys to highlight your preference, then press the key.
Section 13: Set Up 153
Ringer Settings
1. In standby mode, repeatedly press the volume key ( ) on the left side of the phone up or down. Options are:
䢇 Ringer off
䢇 1 Beep
䢇 Vibrate
䢇 Vib+Ring
䢇 Level 1
䢇 Level 2
䢇 Level 3
䢇 Level 4
䢇 Level 5
2. Press once you’re satisfied with the setting. The phone returns to standby mode.
Call Options
Call Answer
You can select a specific answer mode when you receive an incoming call. Your phone can be preset to answer when you do any of the following:
• Send key—Press to answer an incoming call.
• Folder open—Open the folder to answer an incoming call.
• Any key—Press any key except or key to answer an incoming call.
154
Call Options
1. In standby mode, press the Menu (left) soft key ( ), then press Call Options, and
for Call Answer. The following options appear in the display:
䢇 Send Key
䢇 Folder Open
䢇 Any Key
2. Use the navigation keys to highlight the method you wish to use for answering calls, then press .
Auto Answer
Auto Answer enables your phone to automatically answer calls after a period of time that you specify.
1. In standby mode, press the Menu (left) soft key ( ), then press Call Options, and
for Auto Answer. The following options appear in the display:
䢇 Off
䢇 After 5 sec
䢇 After 3 sec
䢇 After 1 sec
2. Use the navigation keys to highlight the desired setting, then press .
Section 13: Set Up 155
Auto Retry
Auto Retry automatically re-dials a number if the connection fails. Depending upon your location, the number of times your phone automatically dials the number may vary.
1. In standby mode, press the Menu (left) soft key ( ), then press
for Auto Retry. The following options appear in the display:
䢇 Off
䢇 Every 10 sec
䢇 Every 30 sec
䢇 Every 60 sec
2. Use the navigation keys to highlight the desired setting, then press .
Data
Use the Data menu to configure data connection speed and automatic detection settings.
Auto Detect
Select phone options for receiving data or voice, or set data reception to off.
1. In standby mode, press the Menu (left) soft key ( ), then press
for Data.
The following Data menu items appear in the display:
• Auto Detect
• Baud Rate
156
Call Options
2. Use the navigation keys to highlight Auto Detect, then press the key. The following options appear in the display:
• data off—No incoming data calls accepted.
• data for next call—Wait for data call for the next 10 minutes.
• data until powered off—Data calls only, no voice calls accepted.
3. Use the navigation keys to highlight the Auto Detect option you want, then press the key.
The Data menu appears in the display.
Baud Rate
Set the data connection rate.
1. In standby mode, press the Menu (left) soft key ( ), then press Call Options, and
for Data.
The following Data menu items appear in the display:
• Auto Detect
• Baud Rate
2. Use the navigation keys to highlight Baud Rate, then press the key. The following Data Baud Rate options appear in the display:
• Auto
• 19200
• 38400
• 57600
• 115200
• 230400
Section 13: Set Up 157
3. Use the navigation keys to highlight the desired Data
Baud Rate option, then press the key.
The Data menu appears in the display.
TTY Mode
Your phone is fully TTY/TDD compatible. TTY/TDD equipment is connected to your phone through the headset connector on the left side of the phone. TTY
Mode must be enabled before you can use your phone with a TTY/TDD device.
1. In standby mode, press the Menu (left) soft key ( ), then press
for TTY Mode. The following options appear in the display:
䢇 TTY Full
䢇 TTY + TALK
䢇 TTY + HEAR
䢇 TTY Off
2. Use the navigation keys to highlight your selection and press . You’re returned to the Call Options menu.
Note: The TTY icon ( ) appears in the top of the display when the phone is in standby mode.
158
Shortcut
Shortcut
The Down navigation key can be customized to launch any one of numerous applications or functions from standby mode. Use the Shortcut sub-menu to choose the application that you wish the navigation down key to launch.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Shortcut. The following functions appear in the display:
䢇 Message inbox
䢇 Today
䢇 Calendar
䢇 To Do List
䢇 Alarm Clock
䢇 Memo Pad
䢇 Calculator
䢇 Voice Memo
2. Use the navigation keys to highlight the desired function, then press the key.
You can now press the navigation down key in standby mode to launch the function selected in step two.
Section 13: Set Up 159
Language
The language option on your phone can change the language of voice prompts, menus, and key-input.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Language.
The following options appear in the display:
䢇 English
䢇 Spanish
2. Use the navigation keys to highlight your language preference, then press the key.
Clock Set
Use the Clock Set sub-menu to set the time and date, which can be selected as Wallpaper in the Display menu.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Clock Set.The following options appear in the display:
䢇 Main Clock—Set the time and date.
2. Use the navigation keys to highlight the desired submenu, then press the key.
3. For Main Clock, enter the time and date using the keypad and navigation keys. Press the key to save your settings.
Note: In digital service mode, the Main Clock feature is disabled. The network adjusts time and date automatically.
160
Version
Version
You can view both the software version and hardware version running on your phone. This feature is helpful if you need to contact Customer Service.
1. In standby mode, press the Menu (left) soft key ( ), then press (for Set Up) and for Version.
Hardware and software information for your phone appears in the display.
2. Press the key to return to the Set Up menu.
Section 13: Set Up 161
162
Section 14: Health and Safety
Information
Topics Covered
• Health and Safety Information
Section 14: Health and Safety Information 163
Health and Safety Information
Exposure to Radio Frequency (RF) Signals
Certification Information (SAR)
Your wireless phone is a radio transmitter and receiver.
It is designed and manufactured not to exceed the exposure limits for radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the
U.S. government. These FCC exposure limits are derived from the recommendations of two expert organizations, the National Counsel on Radiation
Protection and Measurement (NCRP) and the Institute of Electrical and Electronics Engineers (IEEE). In both cases, the recommendations were developed by scientific and engineering experts drawn from industry, government, and academia after extensive reviews of the scientific literature related to the biological effects of
RF energy.
The exposure limit set by the FCC for wireless mobile phones employs a unit of measurement known as the
Specific Absorption Rate (SAR). The SAR is a measure of the rate of absorption of RF energy by the human body expressed in units of watts per kilogram (W/kg).
The FCC requires wireless phones to comply with a safety limit of 1.6 watts per kilogram (1.6 W/kg). The
FCC exposure limit incorporates a substantial margin of safety to give additional protection to the public and to account for any variations in measurements.
SAR tests are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all
164
Health and Safety Information tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
Before a new model phone is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the
FCC. Tests for each model phone are performed in positions and locations (e.g. at the ear and worn on the body) as required by the FCC. Body-worn operations are restricted to Samsung-supplied, approved, or non-
Samsung designated accessories that have no metal and must provide at least 1.5 cm separation between the device, including its antenna (whether extended or retracted) and the user's body. Non-compliance with the above restrictions may result in violation of FCC RF exposure guidelines.
The FCC has granted an Equipment Authorization for this mobile phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. The maximum SAR values for this model phone as reported to the FCC are:
• Head:1.17 W/Kg.
• Body-worn: 1.14 W/Kg.
SAR information on this and other model phones can be viewed on-line at www.fcc.gov/oet/fccid. To find information that pertains to a particular model phone,
Section 14: Health and Safety Information 165
this site uses the phone FCC ID number which is usually printed somewhere on the case of the phone.
Sometimes it may be necessary to remove the battery pack to find the number. Once you have the FCC ID number for a particular phone, follow the instructions on the website and it should provide values for typical or maximum SAR for a particular phone. Additional product specific SAR information can also be obtained at www.fcc.gov/cgb/sar.
Consumer Information on Wireless Phones
The U.S. Food and Drug Administration (FDA) has published a series of Questions and Answers for consumers relating to radio frequency (RF) exposure from wireless phones. The FDA publication includes the following information:
What kinds of phones are the subject of this update?
The term wireless phone refers here to hand-held wireless phones with built-in antennas, often called
“cell,” “mobile,” or “PCS” phones. These types of wireless phones can expose the user to measurable radio frequency energy (RF) because of the short distance between the phone and the user's head. These
RF exposures are limited by Federal Communications
Commission safety guidelines that were developed with the advice of FDA and other federal health and safety agencies. When the phone is located at greater distances from the user, the exposure to RF is drastically lower because a person's RF exposure decreases rapidly with increasing distance from the source. The so-called “cordless phones,” which have a
166
Consumer Information on Wireless Phones base unit connected to the telephone wiring in a house, typically operate at far lower power levels, and thus produce RF exposures well within the FCC's compliance limits.
Do wireless phones pose a health hazard?
The available scientific evidence does not show that any health problems are associated with using wireless phones. There is no proof, however, that wireless phones are absolutely safe. Wireless phones emit low levels of radio frequency energy (RF) in the microwave range while being used. They also emit very low levels of RF when in the stand-by mode. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low level RF that does not produce heating effects causes no known adverse health effects. Many studies of low level RF exposures have not found any biological effects. Some studies have suggested that some biological effects may occur, but such findings have not been confirmed by additional research. In some cases, other researchers have had difficulty in reproducing those studies, or in determining the reasons for inconsistent results.
What is FDA's role concerning the safety of wireless phones?
Under the law, FDA does not review the safety of radiation-emitting consumer products such as wireless phones before they can be sold, as it does with new drugs or medical devices. However, the agency has authority to take action if wireless phones are shown to emit radio frequency energy (RF) at a level that is
Section 14: Health and Safety Information 167
hazardous to the user. In such a case, FDA could require the manufacturers of wireless phones to notify users of the health hazard and to repair, replace or recall the phones so that the hazard no longer exists.
Although the existing scientific data do not justify FDA regulatory actions, FDA has urged the wireless phone industry to take a number of steps, including the following:
• “Support needed research into possible biological effects of RF of the type emitted by wireless phones;
• “Design wireless phones in a way that minimizes any RF exposure to the user that is not necessary for device function; and
• “Cooperate in providing users of wireless phones with the best possible information on possible effects of wireless phone use on human health.
FDA belongs to an interagency working group of the federal agencies that have responsibility for different aspects of RF safety to ensure coordinated efforts at the federal level. The following agencies belong to this working group:
• “National Institute for Occupational Safety and Health
• “Environmental Protection Agency
• “Federal Communications Commission
• “Occupational Safety and Health Administration
• “National Telecommunications and Information Administration
The National Institutes of Health participates in some interagency working group activities, as well.
FDA shares regulatory responsibilities for wireless phones with the Federal Communications Commission
168
Consumer Information on Wireless Phones
(FCC). All phones that are sold in the United States must comply with FCC safety guidelines that limit RF exposure. FCC relies on FDA and other health agencies for safety questions about wireless phones.
FCC also regulates the base stations that the wireless phone networks rely upon. While these base stations operate at higher power than do the wireless phones themselves, the RF exposures that people get from these base stations are typically thousands of times lower than those they can get from wireless phones.
Base stations are thus not the primary subject of the safety questions discussed in this document.
What are the results of the research done already?
The research done thus far has produced conflicting results, and many studies have suffered from flaws in their research methods. Animal experiments investigating the effects of radio frequency energy (RF) exposures characteristic of wireless phones have yielded conflicting results that often cannot be repeated in other laboratories. A few animal studies, however, have suggested that low levels of RF could accelerate the development of cancer in laboratory animals. However, many of the studies that showed increased tumor development used animals that had been genetically engineered or treated with cancercausing chemicals so as to be pre-disposed to develop cancer in absence of RF exposure. Other studies exposed the animals to RF for up to 22 hours per day.
These conditions are not similar to the conditions under which people use wireless phones, so we don't know
Section 14: Health and Safety Information 169
with certainty what the results of such studies mean for human health.
Three large epidemiology studies have been published since December 2000. Between them, the studies investigated any possible association between the use of wireless phones and primary brain cancer, glioma, meningioma, or acoustic neuroma, tumors of the brain or salivary gland, leukemia, or other cancers. None of the studies demonstrated the existence of any harmful health effects from wireless phones RF exposures.
However, none of the studies can answer questions about long-term exposures, since the average period of phone use in these studies was around three years.
What research is needed to decide whether RF exposure from wireless phones poses a health risk?
A combination of laboratory studies and epidemiological studies of people actually using wireless phones would provide some of the data that are needed. Lifetime animal exposure studies could be completed in a few years. However, very large numbers of animals would be needed to provide reliable proof of a cancer promoting effect if one exists. Epidemiological studies can provide data that is directly applicable to human populations, but ten or more years' follow-up may be needed to provide answers about some health effects, such as cancer. This is because the interval between the time of exposure to a cancer-causing agent and the time tumors develop - if they do - may be many, many years. The interpretation of epidemiological studies is hampered by difficulties in measuring actual RF exposure during day-to-day use of
170
Consumer Information on Wireless Phones wireless phones. Many factors affect this measurement, such as the angle at which the phone is held, or which model of phone is used.
What is FDA doing to find out more about the possible health effects of wireless phone RF?
FDA is working with the U.S. National Toxicology
Program and with groups of investigators around the world to ensure that high priority animal studies are conducted to address important questions about the effects of exposure to radio frequency energy (RF).
FDA has been a leading participant in the World Health
Organization international Electromagnetic Fields
(EMF) Project since its inception in 1996. An influential result of this work has been the development of a detailed agenda of research needs that has driven the establishment of new research programs around the world. The Project has also helped develop a series of public information documents on EMF issues.
FDA and Cellular Telecommunications & Internet
Association (CTIA) have a formal Cooperative
Research and Development Agreement (CRADA) to do research on wireless phone safety. FDA provides the scientific oversight, obtaining input from experts in government, industry, and academic organizations.
CTIA-funded research is conducted through contracts to independent investigators. The initial research will include both laboratory studies and studies of wireless phone users. The CRADA will also include a broad assessment of additional research needs in the context of the latest research developments around the world.
Section 14: Health and Safety Information 171
What steps can I take to reduce my exposure to radio frequency energy from my wireless phone?
If there is a risk from these products - and at this point we do not know that there is - it is probably very small.
But if you are concerned about avoiding even potential risks, you can take a few simple steps to minimize your exposure to radio frequency energy (RF). Since time is a key factor in how much exposure a person receives, reducing the amount of time spent using a wireless phone will reduce RF exposure.
• “If you must conduct extended conversations by wireless phone every day, you could place more distance between your body and the source of the RF, since the exposure level drops off dramatically with distance. For example, you could use a headset and carry the wireless phone away from your body or use a wireless phone connected to a remote antenna.
Again, the scientific data do not demonstrate that wireless phones are harmful. But if you are concerned about the RF exposure from these products, you can use measures like those described above to reduce your
RF exposure from wireless phone use.
What about children using wireless phones?
The scientific evidence does not show a danger to users of wireless phones, including children and teenagers. If you want to take steps to lower exposure to radio frequency energy (RF), the measures described above would apply to children and teenagers using wireless phones. Reducing the time of wireless phone use and increasing the distance between the user and the RF source will reduce RF exposure.
172
Consumer Information on Wireless Phones
Some groups sponsored by other national governments have advised that children be discouraged from using wireless phones at all. For example, the government in the United Kingdom distributed leaflets containing such a recommendation in December 2000. They noted that no evidence exists that using a wireless phone causes brain tumors or other ill effects. Their recommendation to limit wireless phone use by children was strictly precautionary; it was not based on scientific evidence that any health hazard exists.
Do hands-free kits for wireless phones reduce risks from exposure to RF emissions?
Since there are no known risks from exposure to RF emissions from wireless phones, there is no reason to believe that hands-free kits reduce risks. Hands-free kits can be used with wireless phones for convenience and comfort. These systems reduce the absorption of
RF energy in the head because the phone, which is the source of the RF emissions, will not be placed against the head. On the other hand, if the phone is mounted against the waist or other part of the body during use, then that part of the body will absorb more RF energy.
Wireless phones marketed in the U.S. are required to meet safety requirements regardless of whether they are used against the head or against the body. Either configuration should result in compliance with the safety limit.
Section 14: Health and Safety Information 173
Do wireless phone accessories that claim to shield the head from RF radiation work?
Since there are no known risks from exposure to RF emissions from wireless phones, there is no reason to believe that accessories that claim to shield the head from those emissions reduce risks. Some products that claim to shield the user from RF absorption use special phone cases, while others involve nothing more than a metallic accessory attached to the phone. Studies have shown that these products generally do not work as advertised. Unlike “hands-free” kits, these so-called
“shields” may interfere with proper operation of the phone. The phone may be forced to boost its power to compensate, leading to an increase in RF absorption. In
February 2002, the Federal trade Commission (FTC) charged two companies that sold devices that claimed to protect wireless phone users from radiation with making false and unsubstantiated claims. According to
FTC, these defendants lacked a reasonable basis to substantiate their claim.
What about wireless phone interference with medical equipment?
Radio frequency energy (RF) from wireless phones can interact with some electronic devices. For this reason,
FDA helped develop a detailed test method to measure electromagnetic interference (EMI) of implanted cardiac pacemakers and defibrillators from wireless telephones. This test method is now part of a standard sponsored by the Association for the Advancement of
Medical instrumentation (AAMI). The final draft, a joint effort by FDA, medical device manufacturers, and
174
Consumer Information on Wireless Phones many other groups, was completed in late 2000. This standard will allow manufacturers to ensure that cardiac pacemakers and defibrillators are safe from wireless phone EMI. FDA has tested wireless phones and helped develop a voluntary standard sponsored by the Institute of Electrical and Electronic Engineers
(IEEE). This standard specifies test methods and performance requirements for hearing aids and wireless phones so that no interference occurs when a person uses a compatible phone and a compatible hearing aid at the same time. This standard was approved by the IEEE in 2000.
FDA continues to monitor the use of wireless phones for possible interactions with other medical devices.
Should harmful interference be found to occur, FDA will conduct testing to assess the interference and work to resolve the problem.
Additional information on the safety of RF exposures from various sources can be obtained from the following organizations:
• FCC RF Safety Program: http://www.fcc.gov/oet/rfsafety/
• Environmental Protection Agency (EPA): http://www.epa.gov/radiation/
• Occupational Safety and Health Administration's (OSHA): http://www.osha.slc.gov/SLTC/radiofrequencyradiation/ index.html
• National institute for Occupational Safety and Health (NIOSH): http://www.cdc.gov/niosh/emfpg.html
• World health Organization (WHO): http://www.who.int/peh-emf/
Section 14: Health and Safety Information 175
• International Commission on Non-Ionizing Radiation Protection: http://www.icnirp.de
• National Radiation Protection Board (UK): http://www.hpa.org.uk/radiation/
• US food and Drug Administration: http://www.fda.gov/cellphones
Road Safety
Your wireless phone gives you the powerful ability to communicate by voice, almost anywhere, anytime. But an important responsibility accompanies the benefits of wireless phones, one that every user must uphold.
When driving a car, driving is your first responsibility.
When using your wireless phone behind the wheel of a car, practice good common sense and remember the following tips:
1. Get to know your wireless phone and its features, such as speed dial and redial. If available, these features help you to place your call without taking your attention off the road.
2. When available, use a hands-free device. If possible, add an additional layer of convenience and safety to your wireless phone with one of the many hands free accessories available today.
3. Position your wireless phone within easy reach. Be able to access your wireless phone without removing your eyes from the road. If you get an incoming call at an inconvenient time, let your voice mail answer it for you.
176
Road Safety
4. Let the person you are speaking with know you are driving; if necessary, suspend the call in heavy traffic or hazardous weather conditions. Rain, sleet, snow, ice and even heavy traffic can be hazardous.
5. Do not take notes or look up phone numbers while driving. Jotting down a “to do” list or flipping through your address book takes attention away from your primary responsibility, driving safely.
6. Dial sensibly and assess the traffic; if possible, place calls when you are not moving or before pulling into traffic. Try to plan calls when your car will be stationary.
If you need to make a call while moving, dial only a few numbers, check the road and your mirrors, then continue.
7. Do not engage in stressful or emotional conversations that may be distracting. Make people you are talking with aware you are driving and suspend conversations that have the potential to divert your attention from the road.
8. Use your wireless phone to call for help. Dial 9-1-1 or other local emergency number in the case of fire, traffic accident or medical emergencies. Remember, it is a free call on your wireless phone!
9. Use your wireless phone to help others in emergencies. If you see an auto accident, crime in progress or other serious emergency where lives are in danger, call 9-1-1 or other local emergency number, as you would want others to do for you.
Section 14: Health and Safety Information 177
10. Call roadside assistance or a special non-emergency wireless assistance number when necessary. If you see a broken-down vehicle posing no serious hazard, a broken traffic signal, a minor traffic accident where no one appears injured, or a vehicle you know to be stolen, call roadside assistance or other special non-emergency number.
“The wireless industry reminds you to use your phone safely when driving.”
For more information, please call 1-888-901-SAFE, or visit our web-site www.wow-com.com
Provided by the Cellular Telecommunications &
Internet Association
Operating Environment
Remember to follow any special regulations in force in any area and always switch your phone off whenever it is forbidden to use it, or when it may cause interference or danger. When connecting the phone or any accessory to another device, read its user's guide for detailed safety instructions. Do not connect incompatible products.
As with other mobile radio transmitting equipment, users are advised that for the satisfactory operation of the equipment and for the safety of personnel, it is recommended that the equipment should only be used in the normal operating position (held to your ear with the antenna pointing over your shoulder if you are using an external antenna).
178
Using Your Phone Near Other Electronic Devices
Using Your Phone Near Other Electronic Devices
Most modern electronic equipment is shielded from radio frequency (RF) signals. However, certain electronic equipment may not be shielded against the
RF signals from your wireless phone. Consult the manufacturer to discuss alternatives.
Pacemakers
Pacemaker manufacturers recommend that a minimum distance of 15 cm (6 inches) be maintained between a wireless phone and a pacemaker to avoid potential interference with the pacemaker.
These recommendations are consistent with the independent research and recommendations of
Wireless Technology Research.
Persons with pacemakers:
• should always keep the phone more than 15 cm (6 inches) from their pacemaker when the phone is switched on.
• should not carry the phone in a breast pocket.
• should use the ear opposite the pacemaker to minimize potential interference.
If you have any reason to suspect that interference is taking place, switch your phone off immediately.
Hearing Aids
Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may wish to consult your hearing aid manufacturer to discuss alternatives.
Section 14: Health and Safety Information 179
Other Medical Devices
If you use any other personal medical devices, consult the manufacturer of your device to determine if it is adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information. Switch your phone off in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.
Vehicles
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle.
Posted Facilities
Switch your phone off in any facility where posted notices require you to do so.
Potentially Explosive Environments
Switch your phone off when in any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.
180
Emergency Calls
Users are advised to switch the phone off while at a refueling point (service station). Users are reminded of the need to observe restrictions on the use of radio equipment in fuel depots (fuel storage and distribution areas), chemical plants or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often but not always clearly marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as propane or butane), areas where the air contains chemicals or particles, such as grain, dust or metal powders, and any other area where you would normally be advised to turn off your vehicle engine.
Emergency Calls
This phone, like any wireless phone, operates using radio signals, wireless and landline networks as well as user-programmed functions, which cannot guarantee connection in all conditions. Therefore, you should never rely solely on any wireless phone for essential communications (medical emergencies, for example).
Remember, to make or receive any calls the phone must be switched on and in a service area with adequate signal strength. Emergency calls may not be possible on all wireless phone networks or when certain network services and/or phone features are in use. Check with local Wireless Providers.
Section 14: Health and Safety Information 181
To make an emergency call:
1. If the phone is not on, switch it on.
2. Key in the emergency number for your present location
(for example, 911 or other official emergency number).
Emergency numbers vary by location.
3. Press the key.
If certain features are in use (call barring, for example), you may first need to deactivate those features before you can make an emergency call. Consult this document and your local Wireless Provider.
When making an emergency call, remember to give all the necessary information as accurately as possible.
Remember that your phone may be the only means of communication at the scene of an accident; do not cut off the call until given permission to do so.
Restricting Children's access to your Phone
Your phone is not a toy. Children should not be allowed to play with it because they could hurt themselves and others, damage the phone or make calls that increase your phone bill.
182
FCC Notice and Cautions
FCC Notice and Cautions
FCC Notice
The phone may cause TV or radio interference if used in close proximity to receiving equipment. The FCC can require you to stop using the phone if such interference cannot be eliminated.
Vehicles using liquefied petroleum gas (such as propane or butane) must comply with the National Fire
Protection Standard (NFPA-58). For a copy of this standard, contact the National Fire Protection
Association, One Batterymarch Park, Quincy, MA
02269, Attn: Publication Sales Division.
Cautions
Any changes or modifications to your phone not expressly approved in this document could void your warranty for this equipment, and void your authority to operate this equipment. Only use approved batteries, antennas and chargers. The use of any unauthorized accessories may be dangerous and void the phone warranty if said accessories cause damage or a defect to the phone.
Although your phone is quite sturdy, it is a complex piece of equipment and can be broken. Avoid dropping, hitting, bending or sitting on it.
Section 14: Health and Safety Information 183
Other Important Safety Information
• Only qualified personnel should service the phone or install the phone in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty applicable to the device.
• Check regularly that all wireless phone equipment in your vehicle is mounted and operating properly.
• Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the phone, its parts or accessories.
• For vehicles equipped with an air bag, remember that an air bag inflates with great force. Do not place objects, including both installed or portable wireless equipment in the area over the air bag or in the air bag deployment area. If wireless equipment is improperly installed and the air bag inflates, serious injury could result.
• Switch your phone off before boarding an aircraft. The use of wireless phone in aircraft is illegal and may be dangerous to the aircraft's operation.
• Failure to observe these instructions may lead to the suspension or denial of telephone services to the offender, or legal action, or both.
Product Performance
Getting the Most Out of Your Signal Reception
The quality of each call you make or receive depends on the signal strength in your area. Your phone informs you of the current signal strength by displaying a number of bars next to the signal strength icon. The more bars displayed, the stronger the signal.
If you're inside a building, being near a window may give you better reception.
184
Product Performance
Understanding the Power Save Feature
If your phone is unable to find a signal after 15 minutes of searching, a Power Save feature is automatically activated. If your phone is active, it periodically rechecks service availability or you can check it yourself by pressing any key.
Anytime the Power Save feature is activated, a message displays on the screen. When a signal is found, your phone returns to standby mode.
Understanding How Your Phone Operates
Your phone is basically a radio transmitter and receiver.
When it's turned on, it receives and transmits radio frequency (RF) signals. When you use your phone, the system handling your call controls the power level.
This power can range from 0.006 watts to 0.2 watts in digital mode.
Maintaining Your Phone's Peak Performance
For the best care of your phone, only authorized personnel should service your phone and accessories.
Faulty service may void the warranty.
There are several simple guidelines to operating your phone properly and maintaining safe, satisfactory service.
• Hold the phone with the antenna raised, fully-extended and over your shoulder.
• Try not to hold, bend or twist the phone's antenna.
• Don't use the phone if the antenna is damaged.
• Speak directly into the phone's receiver.
Section 14: Health and Safety Information 185
• Avoid exposing your phone and accessories to rain or liquid spills. If your phone does get wet, immediately turn the power off and remove the battery. If it is inoperable, call Customer
Care for service.
Availability of Various Features/Ring Tones
Many services and features are network dependent and may require additional subscription and/or usage charges. Not all features are available for purchase or use in all areas. Downloadable Ring Tones may be available at an additional cost. Other conditions and restrictions may apply. See your Wireless Provider for additional information.
Battery Standby and Talk Time
Standby and talk times will vary depending on phone usage patterns and conditions. Battery power consumption depends on factors such as network configuration, signal strength, operating temperature, features selected, frequency of calls, and voice, data, and other application usage patterns.
Battery Precautions
• Never use any charger or battery that is damaged in any way.
• Use the battery only for its intended purpose.
• If you use the phone near the network's base station, it uses less power; talk and standby time are greatly affected by the signal strength on the cellular network and the parameters set by the network operator.
• Battery charging time depends on the remaining battery charge and the type of battery and charger used. The battery can be charged and discharged hundreds of times, but it will gradually wear out. When the operation time (talk time and standby time)
186
Battery Precautions is noticeably shorter than normal, it is time to buy a new battery.
• If left unused, a fully charged battery will discharge itself over time.
• Use only Samsung-approved batteries and recharge your battery only with Samsung-approved chargers. When a charger is not in use, disconnect it from the power source. Do not leave the battery connected to a charger for more than a week, since overcharging may shorten its life.
• Extreme temperatures will affect the charging capacity of your battery: it may require cooling or warming first.
• Do not leave the battery in hot or cold places, such as in a car in summer or winter conditions, as you will reduce the capacity and lifetime of the battery. Always try to keep the battery at room temperature. A phone with a hot or cold battery may temporarily not work, even when the battery is fully charged.
Li-ion batteries are particularly affected by temperatures below
0 °C (32 °F).
• Do not short-circuit the battery. Accidental short- circuiting can occur when a metallic object (coin, clip or pen) causes a direct connection between the + and - terminals of the battery (metal strips on the battery), for example when you carry a spare battery in a pocket or bag. Short-circuiting the terminals may damage the battery or the object causing the short-circuiting.
• Dispose of used batteries in accordance with local regulations.
In some areas, the disposal of batteries in household or business trash may be prohibited. For safe disposal options for
Li-Ion batteries, contact your nearest Samsung authorized service center. Always recycle. Do not dispose of batteries in a fire.
Section 14: Health and Safety Information 187
Care and Maintenance
Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you fulfill any warranty obligations and allow you to enjoy this product for many years
• Keep the phone and all its parts and accessories out of the reach of small children's.
• Keep the phone dry. Precipitation, humidity and liquids contain minerals that will corrode electronic circuits.
• Do not use the phone with a wet hand. Doing so may cause an electric shock to you or damage to the phone.
• Do not use or store the phone in dusty, dirty areas, as its moving parts may be damaged.
• Do not store the phone in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.
• Do not store the phone in cold areas. When the phone warms up to its normal operating temperature, moisture can form inside the phone, which may damage the phone's electronic circuit boards.
• Do not drop, knock or shake the phone. Rough handling can break internal circuit boards.
• Do not use harsh chemicals, cleaning solvents or strong detergents to clean the phone. Wipe it with a soft cloth slightly dampened in a mild soap-and-water solution.
• Do not paint the phone. Paint can clog the device's moving parts and prevent proper operation.
• Do not put the phone in or on heating devices, such as a microwave oven, a stove or a radiator. The phone may explode when overheated.
188
Care and Maintenance
• Use only the supplied or an approved replacement antenna.
Unauthorized antennas or modified accessories may damage the phone and violate regulations governing radio devices.
• If the phone, battery, charger or any accessory is not working properly, take it to your nearest qualified service facility. The personnel there will assist you, and if necessary, arrange for service.
Section 14: Health and Safety Information 189
190
Section 15: Warranty Information
Topics Covered
• Standard Limited Warranty
Section 15: Warranty Information 191
Standard Limited Warranty
What is Covered and For How Long?
SAMSUNG TELECOMMUNICATIONS AMERICA,
L.P. (“SAMSUNG”) warrants to the original purchaser
(“Purchaser”) that SAMSUNG's Phones and accessories
(“Products”) are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase and continuing for the following specified period of time after that date:
Phone
Batteries
Leather Case/ Pouch
1 Year
1 Year
90 Days
Other Phone Accessories 1 Year
What is Not Covered? This Limited Warranty is conditioned upon proper use of Product by Purchaser.
This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical, electrical or electromechanical stress, or modification of any part of Product, including antenna, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) any plastic surfaces or other externally exposed parts that are scratched or damaged due to normal use; (d) malfunctions resulting from the use of Product in conjunction with accessories, products, or ancillary/ peripheral equipment not furnished or approved by
192
Standard Limited Warranty
SAMSUNG; (e) defects or damage from improper testing, operation, maintenance, installation, or adjustment; (f) installation, maintenance, and service of
Product, or (g) Product used or purchased outside the
United States or Canada. This Limited Warranty covers batteries only if battery capacity falls below 80% of rated capacity or the battery leaks, and this Limited
Warranty does not cover any battery if (i) the battery has been charged by a battery charger not specified or approved by SAMSUNG for charging the battery, (ii) any of the seals on the battery are broken or show evidence of tampering, or (iii) the battery has been used in equipment other than the SAMSUNG phone for which it is specified.
What are SAMSUNG's Obligations?
During the applicable warranty period, SAMSUNG will repair or replace, at
SAMSUNG's sole option, without charge to Purchaser, any defective component part of Product. To obtain service under this Limited Warranty, Purchaser must return Product to an authorized phone service facility in an adequate container for shipping, accompanied by
Purchaser's sales receipt or comparable substitute proof of sale showing the date of purchase, the serial number of Product and the sellers' name and address. To obtain assistance on where to deliver the Product, call
Samsung Customer Care at 1-888-987-4357. Upon receipt, SAMSUNG will promptly repair or replace the defective Product. SAMSUNG may, at SAMSUNG's sole option, use rebuilt, reconditioned, or new parts or components when repairing any Product or replace
Product with a rebuilt, reconditioned or new Product.
Repaired/replaced leather cases, pouches and holsters
Section 15: Warranty Information 193
will be warranted for a period of ninety (90) days. All other repaired/replaced Product will be warranted for a period equal to the remainder of the original Limited
Warranty on the original Product or for 90 days, whichever is longer. All replaced parts, components, boards and equipment shall become the property of
SAMSUNG. If SAMSUNG determines that any Product is not covered by this Limited Warranty, Purchaser must pay all parts, shipping, and labor charges for the repair or return of such Product.
WHAT ARE THE LIMITS ON SAMSUNG'S WARRANTY/LIABILITY?
EXCEPT AS SET FORTH IN THE EXPRESS
WARRANTY CONTAINED HEREIN, PURCHASER
TAKES THE PRODUCT “AS IS,” AND SAMSUNG
MAKES NO WARRANTY OR REPRESENTATION
AND THERE ARE NO CONDITIONS, EXPRESS OR
IMPLIED, STATUTORY OR OTHERWISE, OF ANY
KIND WHATSOEVER WITH RESPECT TO THE
PRODUCT, INCLUDING BUT NOT LIMITED TO:
• “THE MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS
FOR ANY PARTICULAR PURPOSE OR USE;
• “WARRANTIES OF TITLE OR NON-INFRINGEMENT;
• “DESIGN, CONDITION, QUALITY, OR PERFORMANCE OF THE
PRODUCT;
• “THE WORKMANSHIP OF THE PRODUCT OR THE COMPONENTS
CONTAINED THEREIN; OR
• “COMPLIANCE OF THE PRODUCT WITH THE REQUIREMENTS OF
ANY LAW, RULE, SPECIFICATION OR CONTRACT PERTAINING
THERETO.
NOTHING CONTAINED IN THE INSTRUCTION
MANUAL SHALL BE CONSTRUED TO CREATE AN
EXPRESS WARRANTY OF ANY KIND
194
Standard Limited Warranty
WHATSOEVER WITH RESPECT TO THE PRODUCT.
ALL IMPLIED WARRANTIES AND CONDITIONS
THAT MAY ARISE BY OPERATION OF LAW,
INCLUDING IF APPLICABLE THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE
HEREBY LIMITED TO THE SAME DURATION OF
TIME AS THE EXPRESS WRITTEN WARRANTY
STATED HEREIN. SOME STATES/PROVINCES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. IN
ADDITION, SAMSUNG SHALL NOT BE LIABLE FOR
ANY DAMAGES OF ANY KIND RESULTING FROM
THE PURCHASE, USE, OR MISUSE OF, OR
INABILITY TO USE THE PRODUCT OR ARISING
DIRECTLY OR INDIRECTLY FROM THE USE OR
LOSS OF USE OF THE PRODUCT OR FROM THE
BREACH OF THE EXPRESS WARRANTY,
INCLUDING INCIDENTAL, SPECIAL,
CONSEQUENTIAL OR SIMILAR DAMAGES, OR
LOSS OF ANTICIPATED PROFITS OR BENEFITS, OR
FOR DAMAGES ARISING FROM ANY TORT
(INCLUDING NEGLIGENCE OR GROSS
NEGLIGENCE) OR FAULT COMMITTED BY
SAMSUNG, ITS AGENTS OR EMPLOYEES, OR FOR
ANY BREACH OF CONTRACT OR FOR ANY CLAIM
BROUGHT AGAINST PURCHASER BY ANY OTHER
PARTY. SOME STATES/PROVINCES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY
Section 15: Warranty Information 195
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS, WHICH VARY FROM STATE
TO STATE/PROVINCE TO PROVINCE. THIS
LIMITED WARRANTY SHALL NOT EXTEND TO
ANYONE OTHER THAN THE ORIGINAL
PURCHASER OF THIS PRODUCT AND STATES
PURCHASER'S EXCLUSIVE REMEDY. IF ANY
PORTION OF THIS LIMITED WARRANTY IS HELD
ILLEGAL OR UNENFORCEABLE BY REASON OF
ANY LAW, SUCH PARTIAL ILLEGALITY OR
UNENFORCEABILITY SHALL NOT AFFECT THE
ENFORCEABILITY FOR THE REMAINDER OF THIS
LIMITED WARRANTY WHICH PURCHASER
ACKNOWLEDGES IS AND WILL ALWAYS BE
CONSTRUED TO BE LIMITED BY ITS TERMS OR AS
LIMITED AS THE LAW PERMITS. THE PARTIES
UNDERSTAND THAT THE PURCHASER MAY USE
THIRD-PARTY SOFTWARE OR EQUIPMENT IN
CONJUNCTION WITH THE PRODUCT. SAMSUNG
MAKES NO WARRANTIES OR REPRESENTATIONS
AND THERE ARE NO CONDITIONS, EXPRESS OR
IMPLIED, STATUTORY OR OTHERWISE, AS TO THE
QUALITY, CAPABILITIES, OPERATIONS,
PERFORMANCE OR SUITABILITY OF ANY
THIRDPARTY SOFTWARE OR EQUIPMENT,
WHETHER SUCH THIRD-PARTY SOFTWARE OR
EQUIPMENT IS INCLUDED WITH THE PRODUCT
DISTRIBUTED BY SAMSUNG OR OTHERWISE,
INCLUDING THE ABILITY TO INTEGRATE ANY
SUCH SOFTWARE OR EQUIPMENT WITH THE
PRODUCT. THE QUALITY, CAPABILITIES,
196
Standard Limited Warranty
OPERATIONS, PERFORMANCE AND SUITABILITY
OF ANY SUCH THIRD-PARTY SOFTWARE OR
EQUIPMENT LIE SOLELY WITH THE PURCHASER
AND THE DIRECT VENDOR, OWNER OR SUPPLIER
OF SUCH THIRD-PARTY SOFTWARE OR
EQUIPMENT, AS THE CASE MAY BE.
This Limited Warranty allocates risk of Product failure between Purchaser and SAMSUNG, and SAMSUNG's
Product pricing reflects this allocation of risk and the limitations of liability contained in this Limited Warranty.
The agents, employees, distributors, and dealers of
SAMSUNG are not authorized to make modifications to this Limited Warranty, or make additional warranties binding on SAMSUNG. Accordingly, additional statements such as dealer advertising or presentation, whether oral or written, do not constitute warranties by
SAMSUNG and should not be relied upon.
Samsung Telecommunications America, L.P.
1301 East Lookout Drive
Richardson, Texas 75082
Phone: 1-800-SAMSUNG
Phone: 1-888-987-HELP (4357)
©2005 Samsung Telecommunications America. All rights reserved.
No reproduction in whole or in part allowed without prior written approval. Specifications and availability subject to change without notice.
Printed in Korea
Section 15: Warranty Information 197
198
Index
Symbols
@metro
@metro Catalog
A
Alerts
B
Battery
charging
Low battery indicator
removal
Travel adapter
C
Call Functions
Adjusting the Call Volume
Answering a Call
Call Log
Making a Call—Number
Entry Dialing
Making a Call—Speed
Dialing
Making a Call—Voice Dialing
Call Options
Auto Answer
Auto Retry
Call Answer
TTY/TDD
Clock Set
Contacts List
open
Creating and Sending New
Messages
D
Display screen icons
Display Settings
Animation
Auto Hyphen
Backlight
Banner
Contrast
Dial Digits
Dial Screen
Menu Style
Service LED
E
Entering Text
Entering Numbers
Entering Symbols
Entering Upper and Lower Case Letters
Text Entry Modes
Erase memos
Exit Mobile Web
G
Getting Started
Activating Your Phone
Understanding this User
Manual
Voicemail
199
H
Health and Safety Information
I
In Use Menu Outline
K
Key Beep
L
Language
M
Memo Pad
Review, add, edit, and erase memos
Menu Navigation
Message Alerts
Message Folders
Draft Box
Inbox
Messages and Lock
Mode
Outbox
Saved Box
Voice Mail
Message Send Options
Message Setting
Messaging
Deleting Messages
Message Folders
Message Send Options
Message Settings
200
Retrieving New Messages
Sending New Messages
Voice Mail
MetroConnect
MetroPCS Card
Mobile Web
Using Links
Using Mobile Web
MyMetro
MetroConnect
MetroPCS Card
Monthly Bill
N
How Mobile Web Keys
Work
Launching Mobile Web
Number Entry Dialing
O
Open View of Your Phone
P
Personal Organizer
Alarm Clock
Calculator
Calendar
Count Down
Memo Pad
Today
To-Do List
Voice Memo
World Time
Phone Modes
R
Record memos
Retrieving New Messages
Ringer Settings
Ringer Type
Roam Ringer
Roaming
S
Security Settings
Change Lock
Emergency #
Erase Memory
Lock Phone
Resetting Your Phone
Restriction
Voice Privacy
Set Up
Call
Data
Display
Location
Network Selection
Ringer
Security
Shortcuts
Sound Settings
Whisper Mode
Sounds
Alerts
Key Beep
Power On/Off
Ringer Type
Roam Ringer
Volume/Vibrate
Speed Dialing
One-Touch Dialing
Three-Touch Dialing
Two-Touch Dialing
Standard Limited Warranty
T
Tools
U
Understanding Your Contacts
Adding a New Contact
Entry
Deleting a Contact Entry
Editing an Existing Contact Entry
Finding a Contact Entry
Finding My Phone Number
Memory
Pauses
Understanding Your Phone
Closed View of Your
Phone
Command Keys
Display Screen
201
Features of Your Phone
V
Version
Voice
Voice Dialing
Voice Kit
erase all memos
record memos
review and erase memos
Voice Mail
Voice Memo
VoiceSignal
Voice Memos
W
Warranty Information
202
advertisement
Related manuals
advertisement
Table of contents
- 9 Topics Covered
- 10 Activating Your Phone
- 10 Install the Battery
- 11 Remove the Battery
- 11 Turn Your Phone On
- 12 Turn Your Phone Off
- 12 Charging the Battery
- 12 Use the Travel Adapter
- 13 Low battery indicator
- 13 Setting Up Your Voice Mail
- 14 Understanding this User Manual
- 15 Topics Covered
- 16 Features of Your Phone
- 16 Closed View of Your Phone
- 17 Command Keys and Features
- 18 Open View of Your Phone
- 18 Command Keys and Features
- 20 Understanding the Display Screen
- 20 Display screen icons
- 23 Topics Covered
- 24 Making a Call-Number Entry Dialing
- 24 Manual Pause Calling
- 25 Making a Call-Speed Dialing
- 25 One-Touch Dialing
- 25 Two-Touch Dialing
- 26 Three-Touch Dialing
- 26 Pause Dialing From a Contacts Entry
- 26 Making a Call-Voice Dialing
- 26 Using Voice Dial
- 27 Voice Dialing Tips:
- 27 Dialing a Name
- 28 Dialing a Number
- 29 Pause Dialing From a Contacts Entry
- 29 Answering a Call
- 30 Answering an Incoming Call
- 30 Ignoring a Call
- 30 Adjusting the Call Volume
- 31 Calls Log
- 31 Review the Calls Log
- 31 Outgoing Calls
- 32 Incoming Calls
- 33 Missed Calls
- 34 Erase Logs
- 34 Erase All Calls
- 34 Call Timer
- 35 Phone Modes
- 35 Standby Mode
- 36 Receive Messages in Standby Mode
- 36 Talk Mode
- 36 Lock Mode
- 36 Silent Mode
- 37 Enter Silent Mode
- 37 Exit Silent Mode
- 37 Vibrate Mode
- 38 Text Input Modes
- 38 ABC Mode
- 38 Symbol Mode
- 39 123 Mode
- 39 T9 Word Text Entry Mode
- 40 Roaming
- 40 What is Roaming
- 40 How Roaming Works
- 41 Topics Covered
- 42 Menu Navigation
- 42 Navigate Using Keys
- 42 Return to the Previous Menu
- 42 Navigate Using a Shortcut
- 43 Navigation Key Shortcuts
- 44 In Use Menu Outline
- 45 Menus and sub-menus
- 53 Topics Covered
- 54 Text Entry Modes
- 54 Entering Upper and Lower Case Letters
- 55 Entering Symbols
- 56 Entering Numbers
- 56 Using T9 Mode
- 57 Changing the Text Entry Mode
- 59 Topics Covered
- 60 Your Contacts List
- 60 Open Your Contacts List
- 61 Adding a New Contacts Entry
- 61 Using the Contacts Add Option
- 62 Adding Pauses to Contacts Numbers
- 63 Store Pauses in a Contacts Entry
- 63 Saving a Number from a Call
- 64 Storing Number from a Calls Log
- 66 Finding a Contacts Entry
- 66 Voice Method
- 67 Menu Method
- 67 Find by Name
- 69 Find by Entry
- 69 Find by Group
- 71 Editing an Existing Contact Entry
- 72 Assigning Speed Dial Numbers
- 72 Add a Number or E-mail Address to an Existing Entry
- 74 Edit an Existing E-mail Address
- 75 Renaming a Contacts Group
- 75 Deleting a Contact Entry
- 76 Finding My Phone Number
- 77 Memory
- 79 Topics Covered
- 80 @metro Catalog
- 81 Settings
- 82 Help
- 82 Buying New Apps
- 82 What do I pay?
- 83 Charges
- 83 Cancelling Subscription
- 83 Demo Apps
- 83 Removing Apps
- 84 Disabled Apps
- 84 Restoring Apps
- 84 Expired Apps
- 85 Topics Covered
- 86 Monthly Bill
- 86 MetroConnect
- 87 MetroPCS Card
- 88 Request Balance
- 88 Pay Monthly Bill
- 89 Topics Covered
- 90 Creating and Sending New Messages
- 90 Creating and Sending a Text (TXT) Message
- 91 Message Send Options
- 92 Retrieving New Messages
- 92 Retrieve Messages While in a Call
- 93 Voice Mail
- 93 Voice Mail Setup
- 93 Check your Voice Mail
- 94 Message Folders
- 94 Voice Mail
- 94 Inbox
- 96 Outbox
- 97 Draft Box
- 97 Saved Box
- 98 Messages and Lock Mode
- 98 Message Settings
- 99 Message Alerts
- 100 Deleting Messages
- 103 Topics Covered
- 104 Volume/Vibrate
- 104 Ringer Type
- 105 Key Beep
- 105 Key Beep Volume
- 106 Key Beep Tone Length
- 106 Alerts
- 107 Power On/Off
- 108 Roam Ringer
- 108 Whisper Mode
- 109 Topics Covered
- 110 Tools
- 110 Opening Tools
- 112 Voice
- 112 VoiceSignal Commands
- 112 Voice-Activating Your Contacts List
- 113 Ending Calls Before Restarting the VoiceSignal Software
- 113 Starting VoiceSignal
- 113 Voice Command Tips:
- 114 Voice Memo
- 114 Record a Voice Memo
- 115 Review and Erase Voice Memos
- 116 Erase All Voice Memos at One Time
- 116 Adapting Digits
- 116 Tips for Adapting Digit dialing:
- 117 Voice Command Method
- 117 Voice Setting Menu Method
- 118 Choice Lists Settings
- 118 Voice Command Method
- 119 Voice Setting Menu Method
- 120 Text-To-Speech (TTS)
- 120 Voice Settings
- 120 Sound
- 121 Voice Launch
- 121 About
- 122 Today
- 122 Add a New Event
- 124 Calendar
- 124 View an event
- 125 To-Do List
- 126 Add, Edit, and Erase To-Do List Tasks
- 127 Alarm Clock
- 128 When an Alarm Sounds
- 128 Turn Off the Alarm
- 129 Memo Pad
- 130 Review, Add, Edit, and Erase Memos
- 130 World Time
- 131 Calculator
- 132 Count Down
- 133 Review, Add, Edit, and Erase Count Down Events
- 135 Topics Covered
- 136 Mobile Web
- 136 Stored web content
- 136 Launching Mobile Web
- 137 Exit Mobile Web
- 137 Using Mobile Web
- 137 Mobile Web soft keys
- 138 Place a call while using Mobile Web
- 138 Using Links
- 138 How Mobile Web Keys Work
- 141 Topics Covered
- 142 Location Setting
- 142 Network Selection
- 143 Security Settings
- 143 Lock Phone
- 144 Change Lock
- 145 Emergency #
- 146 Store Emergency Numbers
- 146 Call Emergency Numbers in Lock Mode
- 146 Voice Privacy
- 147 Restriction
- 147 Erase Memory
- 148 Resetting Your Phone
- 148 Display Settings
- 149 Menu Style
- 149 Animation
- 150 Banner
- 150 Backlight
- 151 Contrast
- 152 Auto Hyphen
- 152 Dial Digits
- 153 Dial Screen
- 153 Service LED
- 153 Turn the Service LED on or off
- 154 Ringer Settings
- 154 Call Options
- 154 Call Answer
- 155 Auto Answer
- 156 Auto Retry
- 156 Data
- 156 Auto Detect
- 157 Baud Rate
- 158 TTY Mode
- 159 Shortcut
- 160 Language
- 160 Clock Set
- 161 Version
- 163 Topics Covered
- 164 Health and Safety Information
- 164 Exposure to Radio Frequency (RF) Signals
- 164 Certification Information (SAR)
- 166 Consumer Information on Wireless Phones
- 166 What kinds of phones are the subject of this update?
- 167 Do wireless phones pose a health hazard?
- 167 What is FDA's role concerning the safety of wireless phones?
- 169 What are the results of the research done already?
- 170 What research is needed to decide whether RF exposure from wireless phones poses a health risk?
- 171 What is FDA doing to find out more about the possible health effects of wireless phone RF?
- 172 What steps can I take to reduce my exposure to radio frequency energy from my wireless phone?
- 172 What about children using wireless phones?
- 173 Do hands-free kits for wireless phones reduce risks from exposure to RF emissions?
- 174 Do wireless phone accessories that claim to shield the head from RF radiation work?
- 174 What about wireless phone interference with medical equipment?
- 176 Road Safety
- 178 Operating Environment
- 179 Using Your Phone Near Other Electronic Devices
- 179 Pacemakers
- 179 Persons with pacemakers:
- 179 Hearing Aids
- 180 Other Medical Devices
- 180 Vehicles
- 180 Posted Facilities
- 180 Potentially Explosive Environments
- 181 Emergency Calls
- 182 Restricting Children's access to your Phone
- 183 FCC Notice and Cautions
- 183 FCC Notice
- 183 Cautions
- 184 Other Important Safety Information
- 184 Product Performance
- 184 Getting the Most Out of Your Signal Reception
- 185 Understanding the Power Save Feature
- 185 Understanding How Your Phone Operates
- 185 Maintaining Your Phone's Peak Performance
- 186 Availability of Various Features/Ring Tones
- 186 Battery Standby and Talk Time
- 186 Battery Precautions
- 188 Care and Maintenance
- 191 Topics Covered
- 192 Standard Limited Warranty