EBV260BN
Blower Vac
w w w. a x m i n s t e r. c o . u k
211927
User Manual
Axminster Reference No:
EBV260BN Part No: 211927
INTRODUCTION
EBV260BN engine blower has been designed and built to
deliver superior performance and reliability without
compromise to quality, compromise to quality, comfort, safety,
or durability EBV260BN high performance engines represent
the leading edge of 2-cycle engine technology, delivering
exceptionally high power at remarkably low displacement and
weight . As a professional owner/operator, you’ll soon discover
why EBV260BN is simple in a class by itself!
IMPORTANT!
The information contained in this manual describes available at
the time of production. While every attempt has been made to
give you the very latest information about your
EBV260BN,there may be some differences between your
machine and what is described here . We reserves the right to
make changes in production without prior notice, and without
obligation to make alterations to machines previously
manufactured. Before using this product, consult local
regulation noise restrictions and hours of operation.
CAUTION!
This EBV260BN engine machine is
equipped with a speak-arresting muffler.
Never operate this machine without both the
muffler and spark arrestor installed and
properly functioning!
1
-
-
CONTENTS
Attention Statements………………………3
Product Description……………………… 4
Specifications………………………………4
Assembling the Machine……………………5
Mixing Fuel…………………………………8
Filling the Fuel Tank…………………………9
Starting the Machine…………………………10
Adjusting Engine Speed……………………13
Routine Maintenances………………………15
Storage………………………………………17
Troubleshooting………………………………18
2
-
-
ATTENTION STAEMENTS
This manual contains special “attention statements” surrounded
by boxes and preceded by the triangular Attention Symbol
CAUTION!
WARNING!
A statement preceded by
WARNING contains
Information that should be
acted upon to prevent
serious bodily injury.
A statement preceded by
the word “CAUTION”
contains information that
should be acted upon to
prevent machine damage.
Additional attention statements that are not preceded by the
Attention Symbol are:
IMPORTANT!
A statement preceded by the word “IMPORTANT” is one that
possesses special significance.
NOTE:
A statement proceeded by word “NOTE” contains information
that is handy to know and may make your job easier.
Read and follow this manual. Failure to do so
could result in serious injury.
Wear eye and hearing protection at all times during
the operation of this machine
3
-
-
Do not operate this machine if you are tired, ill or
under the influences of alcohol, drugs, or Medicine.
PRODUCT DESCRIPTION!
The operational procedures described in this manual are
intended to help you get the most from your machine and to
protect you and others from harm. These procedures are general
guidelines only, and are not intended to replace any safely
rules/laws that may be in force in your area. If you have any
question regarding your EBV260BN blower ￡ vacuum, or if
you do not understand something in this manual, your dealer
will be glad to assist you.
WARNING!
Do not make unauthorized
Modifications to this machine
SPECIFICATIONS
Model………………………………………EBV260BN
Dimensions(L×W×H)………………580×355×370
Engine Type……………………………1E34FBN
Cylinder Diameter………………………34mm
Displacement……………………………25.4cc
Fuel…………………………Gasoline/oil mixture 40:1
Carburetor…………Membrane type primer pump
Way of ignition……………………………CDI
Spark plug………………………………RCJ6Y
Starting…………………………………Recoil starter
Fuel Tank Capacity………………………0.5L
Weight…………………………………4.3kg
4
-
-
ASSEMBLING THE MACHINE
1. Assembling the vacuum
(1) Nomenclature
Inhale
pipe
Discharging
NO.1
pipe
Inhale
pipe
NO.2
Dust bag
Lower handle
Fan cover
(2)Assembly
Open the fan cover,
connect inhale pipe
No.1 and No.2
Insert discharging pipe into dust
bag from the jaws of the slide
fastener according to the picture
discharging pipe.
5
-
-
discharging pipe
Put the discharging pipe to the machine.
Herein, use screw M5×10
to reinforce.
2. Install blower machine
(1) Terms
Stop switch
Throttler lever handle
Cleaner cover
Starter handle
Fuel tank
Lower handle
6
-
-
Blow pipe A
Blow pipe B
(2)Install
Put blow pipe B to the machine
by rotating
Put blow A to B by
rotating
Use screw M5×10 to
reinforce
IMPORTANT!
Mix only enough fuel for your immediate needs! If fuel must be
stored longer than 30-days,it should first be treated with a
stabilizer or equivalent product!
7
-
-
WARNING!
Danger form rotating impeller! Stop the engine before
installing or removing the machine tubes! Never perform any
maintenance or assembly procedures on this machine while
the engine is running.
MIXING FUEL
Fuel requirements
□ Use only fresh, clean fuel
□ Use only fuel with an octane rating of 90 or high
□ Mix all fuel with premium 2-cycles engine oil at a
gasoline/oil ratio of 40:1
CAUTION!
Never attempt to mix fuel in the machine fuel tank! Always mix
all fuels in a clean. approved container!
Some gasoline contain alcohol as an oxy genated! Oxy genated
fuels may cause increased engine operating temperatures! Under
certain conditions, alcohol-based fuels may also reduce the
lubricating qualities of some mixing
oils! Never use any fuel containing more than 10% alcohol by
volume! When an oxygenated fuel must be used fuel containing
an ether-based oxygenates such as MTBE is to be
preferred over alcohol!
Whenever possible use 2-cycle oil or equivalent oil mixed at a
40:1 ratio. Be aware that generic oils and some outboard mixing
oils may note intended for use in high-performance air cooled
2-cycle engines, and should never be used in your engine
machine.
8
-
-
WARNING
Danger of fire! Never transfer or store fuels in the presence
Of combustible materials! Before starting the engine, always
move the machine to a clear area at least 10-feet
(3-meters) away form fuels and other combustible materials!
IMPORTANT!
Mix only enough fuel for your immediate needs! If fuel must be
stored longer than 30-days, it should first be treated with a
stabilizer or equivalent product!
FILLING THE FUEL TANK
Remove the fuel cup
WARNING!
Danger of fire and burn injury!
□ Always use extreme care when handling fuel! Fuel is highly
flammable!
□ Never operate this blower if fuel system components are
damaged or are leaking!
□ Never attempt to refuel the engine while it is running !
□ Never attempt to refuel a hot engine! Always allow the
blower engine to cool before fueling!
9
-
-
□ Never smoke or light any fires near the blower or fuel!
□Always transport and store fuels in an approved container!
□ Never place flammable maternal close to the engine muffler!
□ Never operate the blower without a properly functioning
muffler and spark arrestor installed!
□ Never operate the blower unless it is properly assembled and
in good working condition!
1. Place the machine on the ground or on a sturdy work surface,
and wipe any debris from around the fuel cap.
2. Remove the fuel cap.
3. Fill the tank with clean, fresh fuel.
4. Replace the cap, and wide away any spilled fuel before
starting the machine.
STARTING THE MANCHINE
WARNING!
Danger from rotating impeller! The impeller will rotate
Whenever the machine is operated! Never operate this machine
unless the intake cover and machine tubes are properly installed
and in good working order!
Danger from thrown dust or debries! Always wear eye
protection when operating this machine! Never direct the
machine stream toward people or animals!
Never operate this machine unless all controls are properly
installed and in good working order!
10
-
-
WARNING!
The recoil starter can be damaged by abuse!
<Never pull the starter cord to its full length!
<Always engage the starter before cranking the engine!
<Always rewind the starter cord slowly!
Never operate the machine if the tubes are missing or damaged
Starting procedure
1. Prime the fuel system by repeatedly depressing the fuel
primer bulb until no air bubbles are visible in the fuel
discharge line.
2. Cold engine only. Choke the engine by pulling the choke
control to the fully extended position ( choke is closed)
3. Place the machine on the ground, and hold the machine
handle firmly with your right hand .
4. Pull the starter cord slowly until you feel the engine.
5. Start the machine by pulling the starter cord upward rapidly.
If necessary, repeat step 5 two or three times until the engine
starts.
Fuel discharge line
Fuel primer bulb
11
-
-
When the engine starts
IMPORTANT
For maximum vacuum performance and operating life, allow the
engine to warm before use.
1. Run the engine at idle speed until operating temperature is
reached(2 to 3 minutes)
2. As the engine warms, open the choke gradually by slowly
pushing the choke control in to the fully retracted position.
3. The machine should now be ready for use.
If the engine dose not start
Repeat the appropriate starting procedures for “hot” or “cold”
engine. If the engine still will not start, follow the “Starting a
Flooded Engine” procedure (below).
WARNING!
Incorrect spark plug installation
Can result in serious engine
damage!
Choke
rod
Starting a flooded engine
1. Disconnect the spark plug lead, and use the spark plug
wrench to remove the plug in a counterclockwise direction.
2. If the spark plug is fouled or is soaked with fuel, clean or
replace the plug as required.
3. Clean excess fuel form the combustion chamber by cranking
the engine several times while the spark is removed.
12
-
-
4. Install the spark plug and firmly tighten it with the spark
plug wrench. If a torque wrench. If a torque wrench is
available, torque the spark plug to 148-165 inch-pounds.
Reconnect the spark plug lead.
5. Repeat the starting procedures for “ warm engine”
6. If the engine still fails to fire or start, refer to the
troubleshooting flowchart at the end of this manual.
ADJUSTING ENGING IDLE SPEED
Idle speed adjustment
screw
1. Start the engine by following the procedures described on the
preceding pages.
2. Run the engine at idle speed until operating temperature is
reached (2-3 minutes)
3. Use a screwdriver to adjust the engine idle speed to
3000±200r/min
□ Turn the idle screw clockwise to increase engine idle speed.
□ Turn the idle screw counterclockwise to decrease engine idle
speed.
IMPORTANT!
Machine tubes and intake cover must be installed while
adjusting engine idle! Engine idle speed will also be affected if
either the intake cover or machine tubes are blocked, damaged
or incorrectly installed!
STOPPING THE ENGINE
1. Cool the engine by allowing it to run at idle for 2 to 3
minutes.
13
-
-
2. Stop the engine by pulling the stop switch.
(1) Machine noise increases at higher throttle setting!
Always use the lowest throttle setting required to get the
job done!
(2) Never operate the blower when visibility is poor.
(3) Always wear eye protection such as face shield or
goggles while operating this machine.
(4) Wear a dust mask to reduce the risk of inhalation injures.
(5) Wear close-fitting clothing to protect your legs and arms.
(6) Wear hearing protection when operating this machine.
(7) Never operate the blower if any component parts are
damaged, loose, or missing.
1
Using the vacuum
2 Using the blower
Always be aware of the
strength and direction of stream.
Never direct the blower discharge
stream toward people or animals.
14
-
-
ROUTINE MAINTEANCES
Daily maintenance
□ Remove dirt
WARNING!
Before performing any maintenance
and debris
on this machine, stop the engine and
from the blower
disconnect the spark plug wire!
Exterior.
□ Inspect the engine, tank ,and hose for possible fuel leaks, and
repair as necessary.
□ Inspect the engine cooling fins for accumulations of dirt or
debris, and clean as necessary.
□ Inspect the entire machine for damage, loose or missing
components or fastenings, and repair as necessary.
EVERY 10 HOURS (MORE FREQUENTLY IN DUSTY
CONDITIONS)
1. Loosen the air cleaner cover retaining screw, and remove the
cover and filer element.
2. Inspect the element. If the element is distorted or damaged,
replace it with a new one.
3. Wash the element in clean fuel, and squeeze or blow dry.
Wash the air cleaner cover in clean fuel, and wipe or blow
dry.
4. Install the element and cover, and the tighten the cover
retaining screw.
EVERY 10/15 HOURS
1. Use the spark plug wrench to remove the spark plug ( turn
counter-clockwise to remove)
2. Clean and adjust the spark plug gap to 0.6-0.7mm. Replace
any damaged or visibly worn plug with a champion RCJ6Y
or equivalent.
3. Install the spark plug finger-tight in the cylinder head, and
15
-
-
then tighten it firmly with the spark plug wrench. If a torque
wrench is available, torque the spark plug to 148-165 inch
pounds.
EVERY 50 HOURS
More frequently if you note reduced performance
INSPECTION Inspect the entire machine and tubes for damage,
including loose or missing components, and repair as necessary.
SPARK PLUG Replace the spark plug with a champion RCJ6Y,
gapped to (0.6-0.7)mm.
FUEL FILTER Use a wire hook to extract the fuel filter from
inside the fuel filter, and then remove and wash the filer element
in clean fuel.
Before reinstalling the filter, inspect the condition of the fuel
line. If damage or deterioration is noted, the vacuum should be
removed from service until it can be inspected by a trained
service technician.
CAUTION!
Never allow dirt or debris to enter the cylinder bore!
Before removing the speak plug. Thoroughly clean the
the spark plug and cylinder head area!
Allow the engine to cool before servicing the spark plug!
Cylinder tightening or loosening the spark plug while
the engine is hot!
Incorrect spark plug installation can result in serious engine
damage!
16
-
-
STORAGE(30 days or longer)
□ CLEANING Thoroughly clean the machine exterior.
□ INSPECTION Inspect the entire machine and tubes for
damage, including loose or missing components, and repair
as necessary.
□ FUEL Drain the fuel tank, and the clear the carburetor and
lines by running the machine until it stops from lack of fuel.
□ LUBRICATION Remove the spark plug, and then pour
approximately 1/4-oz of oil into the cylinder through the
spark plug hole. Before reinstalling the spark plug, pull the
recoil starter 2 to 3 times to distribute the oil over the
cylinder walls.
□ AIR CLEANER Remove, clean, and reinstall the filter
element as described under .
17
-
-
1E34FBN汽油机明细表（Ⅰ)
Appendix List Engine Parts of Attached Fig
序号
ERP编号
Item
ERP NO.
1
3480
2
5711
3
0956
4
7431
5
0508
6
6457
7
0513
8
4555
9
0498
10
3355
11
4653
12
0473
13
4567
14
7433
15
7438
16
0047
17
6074
18
6468
19
5774
20
8575
21
4562
22
7437
23
4373
24
1957
25
6144
26
0377
27
1848
零部件名称
Part Name
火花塞 RCJ6Y
Spark plug RCJ6Y
螺钉组合 M5X20
Bolt M5X20
缸体
Cylinder
缸体垫
Gasket,cylinder
活塞环
Ring,piston
活塞
Piston
活塞销 8X28
Pin,piston 8X28
活塞销挡环
Ring, snap
滚针轴承8*11*9
Needle bearing
止推垫圈
Washer,thrust
曲轴连杆组
Crank shaft assy
轴承 6001/P5
Bearing 6001/P5
定位销 B3X10
PIN B3X10
曲轴箱垫
Gasket,crankcase
后半曲轴箱
Rear crankcase
油封 12X22X7
Oil seal 12X22X7
挡圈GB896
Stop ring
起动拨盘
Starter pulley
启动扭簧
Starter pawl spring
启动抓
Starter pawl
半圆键 3*3.7*12
Woodruff key
前半曲轴箱
Front crankcase
螺钉 M5X30
Bolt M5X30
磁电机转子
Rotor
进气管垫
Gasket,insulator
进气管
Insulator
螺钉组合 M5X20
Bolt assy M5X20
数量
序号
ERP编号
Qty
Item
ERP NO.
(Ⅰ)
零部件名称
Part Name
化油器垫
Gasket,carburetor
化油器总成
Carburetor comp
数量
Qty
1
28
1154
4
29
1067
1
30
1028
阻风门手柄
Choke Handle
1
1
31
1355
空滤器内罩
Cleaner inside cover
1
2
32
1339
1
33
4238
1
34
0745
2
35
4402
1
36
0963
2
37
1000
1
38
0955
2
39
0900
2
40
6536
1
41
7813
1
42
4459
2
43
4451
2
44
3477
1
45
0957
2
46
0919
2
47
4242
1
1
3
1
1
1
2
阻风门
Choke
自攻螺钉 ST4×10
Bolt ST4×10
空滤器滤芯
Air filter element
螺钉组合 M5X60
Bolt assy M5X60
空滤器外罩
Cover, cleaner
大头螺钉
Knob,cover
消音器垫
Gasket,muffler
消音器(带触媒)
Muffler assy
平垫 5
Washer 5
弹垫 5
Washer 5
螺钉 M5×50
SCREW M5X50
加大平垫 4
Washer 4
隔热垫
Space,ig coil
停车线
Stop wire
磁电机定子
Ignition coil comp
螺钉组合 M4×20
SCREW M4X20
1
1
1
1
1
2
1
1
1
1
4
4
2
2
2
1
1
2
EBV260BN MACHINE PARTS LIST
EBV260BN 机具明细表 (Ⅱ)
序号 ERP编码
Ser.NO. Erp NO.
2-1
5307
2-2
5308
2-3
4342
2-4
6536
2-5
5318
2-6
4388
2-7
5315
2-8
(Ⅱ)
名称
Part Name
吸尘管一
INHALE PIPE NO.1
吸尘管二
INHALE PIPE NO.2
螺钉 M5×16
数量
Qty
序号
ERP编码
Ser.NO. Erp NO.
1
2-32
6622
1
2-33
0957
14
2-34
24
2-35
1
名称
Part Name
自攻丝 4.2×10
ST4.2×10
数量
Qty
1
停车线
STOP WIRE
1
汽油机(1E34FBN)
GASOLING ENGING(1E34FBN)
1
4109
平垫
WASHER
1
2-36
5349
启动绳轮
STARTER POPE REEL
1
6
2-37
8973
启动平簧
COLE SPRING
1
连接块保护罩
CONNECTER SAFETY COVER
1
2-38
7032
5299
保险开关
SAFETY SWITCH
1
2-39
4483
2-9
5310
按钮连接块
BUTTON CONNECTER
1
2-40
3517
启动绳
STARTER POPE
1
2-10
4263
钢平垫 6
WASHER 6
1
2-41
1079
起动手柄
STARTER HANDLE
1
2-11
1000
大头螺钉
SCREW
1
2-42
5309
出尘管
TAIL PIPE
1
2-12
5313
风机网罩
FAN NET COVER
1
2-43
5296
油门绳
THROTTLE WRIE COMP
1
2-13
5282
扭簧轴
WREST SPRING SHAFT
1
2-44
5293
集叶袋
LEAVES ASSY
1
2-14
5281
扭簧
WREST SPRING
1
2-45
5294
背带组合
HARNESS ASSY
1
2-15
5312
1
2-46
8600
回油管(L=70)
RETURN FUEL PIPE(L=70)
1
2-16
4243
1
2-47
0709
油管胶塞
FUEL PIPE RUBBER BUNG
1
2-17
4111
1
2-48
2718
进油管(L=220)
INLET FUEL PIPE(L=220)
1
2-18
5317
1
2-49
0554
燃油过滤器
FILTER CLEANER
1
2-19
4373
4
2-50
6632
油箱盖组合
LID ASSY
1
2-20
5285
左手把胶套
LEFT HANDLE RUBBER COVER
1
2-51
4281
弹垫8
WASHER 8
1
2-21
5311
前蜗壳
FRONT COCHLEA CASE
1
2-52
7493
垫片23*8*1
WASHER 23*8*1
1
2-22
5283
底座
PEDESTAL
4
2-53
5302
2-23
5316
1
2-54
5306
2-24
3310
2
2-55
5402
2-25
5304
下手把
LOWER HANDLE
1
2-56
3785
2-26
5280
油操轴
THROTTLE LEVER SHAFT
1
2-57
6120
2-27
5305
油操手柄
THROTTLE LEVER HANDLE
1
2-58
6305
2-28
5292
停车开关组合
STOP SWITCH COMP
1
2-59
4237
2-29
5295
短停车线
SHORT STOP WIRE
2
2-60
4358
2-30
5303
上手把
UPPER HANGLE
1
2-61
7813
2-31
5285
右手把胶套
RIGHT HANGLE RUBBER COVER
1
2-62
SCREW M5×16
￠5平垫
WASHER 5
管接罩
CONNECT COVER
螺钉 M5×10
SCREW M5×10
后蜗壳
REAR COCHLEA CASS
螺母 M8×1
NUT M8×1
粉碎齿
SHATTER TOOTH
叶轮
IMPELLER
螺钉 M5×30
SCREW
M5×30
油箱
FUEL TANK
螺钉 M5×20
SCREW M5×20
防护罩
volute case
螺钉 M5×30
SCREW M5×30
出风管 A
BLOW THE BREEZE TUBE A
出风管 B
BLOW THE BREEZE TUBE B
起动绳套
GUIDE,rope
轴套
BUSHING
停车线胶塞
PLUG,lead wire
0 型圈 2.5X2
“O” SEALING WASHER
螺钉 M5×30
SCREW M5×30
螺钉组合 M5×10
SCREW M5×10
弹垫 5
WASHER 5
1
3
1
1
1
1
1
1
2
1
4
EBV260BN Blower Vac
211927
Axminster Reference No:
EBV260BN Part No: 211927
Axminster Devon EX13 5PH UK
FREEPHONE 0800 371822
www.axminster.co.uk
">
