CR Series
High Resolution Box Camera
Instruction Manual
Parts Descriptions
3 4 3 4
5
1 2
Top View
1. Back Focus Adjustment
2. Bracket Mount
3. Function Control DIP Switches
4. BNC Composite Video Output
5. Power LED Indicator
6. Video Lens Drive Terminal Block
7. Power Input Terminal Block
(DC/AC Low Voltage)
8. AC Power Input Socket
(AC Mains)
9. CCD Sensor
10. DC Lens Connector
6 7
AC/DC
Low Voltage
Rear View
6
AC Mains
8
9
Front View
Specifications
Power & Dimensions
Power Source
Power Consumption
Operating Temperature
Storage Temperature
Dimensions
Weight
AC Mains: 100~240VAC
Low Voltage: 12VDC / 24VAC
4.5W Max.
-10ºC to +50ºC
-20ºC to +60ºC
66mm (W) x 57mm (H) x 121mm (L)
251.6 g (without lens)
General
Image Picture Element
Scanning Element
Effective Picture Element
Approximate pixels
Resolution
Minimum Illumination
S/N Ratio
D/N Control
AGC Control
Back Light Compensation
Exposure Control
Shutter Speed (AES)
AWB Range
Synchronization
Video Output
NTSC PAL
1/3” Format Interline CCD Sensor
2:1 Interlace 2:1 Interlace
H:15750Hz V:59.94Hz
768(H) x 494(V)
380K
H:15625Hz V:50.0Hz
752(H) x 582(V)
440K
540 TV lines
0.3 lux @ F=1.2
48 dB
Off / On
Normal / Turbo
Off / On
Auto IRIS Lens / Auto Electronics Shutter
Auto illumination Control
1/60 (1/50) ~ 1/100000 sec Max.
2700°K ~ 9700°K
Internal / Line Lock
1.0Vpp 75Ω BNC unbalanced
10
Side View
5
Connection and Adjustment
Precautions
This product must be installed and maintained in accordance with good installation practices by qualified personnel only.
To prevent damage to your camera or injury to yourself or to others, read and comply with the safety precautions as follows:
Never attempt to disassemble or modify the camera. Any modification could lead to damages that are not covered by the guarantee.
Make sure the power source is switch off and disconnected before installation. Refer servicing to qualified personnel only.
To prevent fire or electrical shock, use only regulated power supply and the wiring should be used for the appropriate input terminal.
Do not expose or operate the camera in wet areas.
Moisture may damage the camera and also increase the danger of electrical shock.
Do not attempt to aim the camera at the sun or other extremely bright objects. This may cause damage to the CCD and the void of warranty.
Do not touch the lens or the CCD by hands while installing or adjusting the camera. This may cause damage to the camera.
Camera Installation
The camera can be mounted by using either the bracket mount on the top or bottom (see part descripton 2).
The bracket mounts accept standard photographic mounting bolts (1/4" BSW or 20 UNC).
Bracket Mount
Ensure the bracket and mounting surface can support the load of the camera and bracket.
Connecting to the Power Source and Video Output
AC/DC Low Voltage Power Supply:
The camera operates in either 24 VAC or 12 VDC.
Connections are indicated in the rear panel of the camera.
The power supply must be stable power source and should only be installed by qualified personnel.
Connect the 75 Ohm coaxial cable to video output (see part description 7).
Video Output
Power Input
Terminal
AC Mains Power Supply:
The camera operates directly from the mains supply and is supplied with a detachable power supply cord. The operating voltage is 100~240 VAC.
Connect the 75 Ohm coaxial cable to video output
(see part description 7).
Video Output
Please visit our website for more information: www.deview.com
Product specifications subject to change without notice.
Certain product names mentioned herein may by trade names and/or registered trademarks of other companies.
Power Socket
V531-CR005-200
Ver.09/2009
Connection and Adjustment
Lens Installation
Installing the Lens
Protective
Cover
Before installing a lens, you must first remove the protective cover from the camera. If mounting a C-Mount lens, attach the CS mount to the camera.
Adjust the Back Focus to acquire a sharp image
(see Back Focus Adjustment).
Zoom and Focus
Adjustment
Lens
(Optional)
Back Focus Adjustment
There is a mechanism for back focus adjustment.
Unscrew (loosen) the back focus screw.
Move the adjustment to the proper position so as to make the better camera image.
Tighten the screw to lock the back focus adjustment in place.
Manual / Fixed Lens Connection
Back Focus
Adjustment
CS Mount
(for C-type Lens)
Back Focus Adjustment
1. If using a C-mount lens, attach the C-mount before installaing the lens.
2. Movet the back focus adjustment fully to the left with the lens facing towards you
(see Back Focus Adjustment).
3. Install the lens on to the camera.
4. Adjust the Back Focus to the proper positon then secure the screw.
5. Adjust the Zoom and Focus levers of the lens to acquire the clear image.
Back Focus
Adjustment
Zoom and Focus
Adjustment
Lens (Optional)
Direct Drive (D.C.) Lens Connection
1. If using a C-mount lens, attach the C-mount before installaing the lens.
2. Movet the back focus adjustment fully to the left with the lens facing towards you
(see Back Focus Adjustment).
3. Install the lens on to the camera.
4. For Direct Drive Lens application, Connect the DC Lens Connector to the side of the camera. Fit the lens to the camera according to the following connection assignments.
5. Adjust the Back Focus to the proper positon then secure the screw.
6. Adjust the Zoom and Focus levers of the lens to acquire the clear image.
Back Focus
Adjustment
Zoom and Focus
Adjustment
Lens (Optional)
Lens
Connector
4
3
2
1
DC Lens
Pin Assignments
Pin Number DC Drive
Pin 1 Damp-
Pin 2
Pin 3
Damp +
Drive +
Pin 4 Drive -
Video Drive Lens Connection
1. If using a C-mount lens, attach the C-mount before installaing the lens.
2. Movet the back focus adjustment fully to the left with the lens facing towards you (see Back Focus Adjustment).
3. Install the lens on to the camera.
4. For Video Drive Lens application, connect the wires to the rear panel of the camera. Fit the lens to the camera according to the following connection assignments.
5. Adjust the Back Focus to the proper positon then secure the screw.
6. Adjust the Zoom and Focus levers of the lens to acquire the clear image.
Back Focus
Adjustment
Zoom and Focus
Adjustment
Video Lens
Connector
Lens (Optional)
Camera Setup
Camera Configuration
There is a bank of DIP switches in the rear of the camera.
The DIP Switches allow the settings as follows:
LL / INT
In LL Mode, the V-Phase may be adjusted to compensate for connected supply phase differences.
Only applicable for AC supply – otherwise the camera should be operates with INT (internal) sync.
SDN / ON
This feature enables the camera operates in monochrome mode in reduced lighting. Switch to ON to activate.
BLC / ON
The Backlight Compensation feature eliminates the effect of strong background lighting, maintaining the correct exposure.
Switch to ON to activate. When switched to BLC, the feature is off.
AGC / TURBO
The Automatic Gain Control feature can improve picture quality in low lighting conditions. Select TURBO for most applications.
Setting to AGC will remove 'noise' from the image, but it will also limit the camera's sensitivity
AES/ ON
Selecting ON enables Electronic Iris mode, which compensates for excessive light levels by automatically adjusting the camera shutter speed. This mode should only be used with fixed or manual iris lenses.
F.L. / ON
When this switch is set to ON, the camera reduces flicker in the image under fluorescent lighting.
