Datasheet | Aritech ATS4000 Technical data

GE

Security

Advisor MASTER integrated intrusion and access control system designers manual

Version 1.11, January 2005

2

Aritech is a GE Security brand.

Copyright

(c) 2004 GE Security B.V.. All rights reserved. GE Security B.V. grants the right to reprint this manual for internal use only. GE

Security B.V. reserves the right to change information without notice.

ATS Designers Guide

C

ONTENTS

:

1 System components. ............................................................................................................................ 5

1.1

Control panels ............................................................................................................................... 5

1.2

User Interface.............................................................................................................................. 11

1.3

DGP Expansion modules ............................................................................................................ 16

1.4

System accessories .................................................................................................................... 22

1.5

ATS8100 – TITAN Software........................................................................................................ 25

2 System power supply. ........................................................................................................................ 27

2.1

System power supply .................................................................................................................. 27

2.2

System equipment power consumption. ..................................................................................... 29

2.3

Wiring. ......................................................................................................................................... 32

2.4

Connecting other power supplies................................................................................................ 32

3 Communications ................................................................................................................................. 33

3.1

System bus ................................................................................................................................. 33

3.1.1

Wiring........................................................................................................................... 34

3.1.2

Device Addressing....................................................................................................... 36

3.1.3

Bus topology ................................................................................................................ 37

3.2

Local bus..................................................................................................................................... 43

3.2.1

ATS1250/60 access control DGP................................................................................ 43

3.2.2

ATS1290 addressable sensor DGP ............................................................................ 44

3.2.3

ATS1230 Wireless devices DGP................................................................................. 46

3.2.4

ATS1105 and ATS1170 RAS station reader interface ................................................ 47

3.3

PC connection............................................................................................................................. 47

3.3.1

Service connection ...................................................................................................... 47

3.3.2

PC direct connection.................................................................................................... 48

3.3.3

Increasing the range between the control panel and PC. ........................................... 49

3.3.4

Modem connection ...................................................................................................... 50

3.4

Control Panel Network ................................................................................................................ 50

3.4.1

Control panel bus topology and wiring ........................................................................ 51

3.4.2

Examples of CP networks connected by various communications interfaces. ........... 51

3.5

Reporting events to the CS station ............................................................................................. 52

4 Configuration of the Advisor MASTER Integrated System ............................................................. 54

4.1

Control panel selection and configuration................................................................................... 55

4.1.1

The procedure of selecting and configuring the alarm system control panel .............. 56

4.2

Configuring the DGP expansion modules................................................................................... 59

4.3

Areas ........................................................................................................................................... 61

4.4

Access control............................................................................................................................. 61

4.4.1

Basic Access Control in the Control Panel .................................................................. 62

4.4.2

Advanced Access Control of the ATS1250 DGP. ....................................................... 63

4.4.3

Advanced Access Control of the ATS1260 DGP ........................................................ 65

4.5

Cards and Readers ..................................................................................................................... 66

4.5.1

Advisor MASTER System Readers ............................................................................. 66

4.5.2

Other readers............................................................................................................... 66

4.5.3

Cards. .......................................................................................................................... 68

5 Network System Configuration.......................................................................................................... 70

6 ATS system Smart Cards. .................................................................................................................. 71

6.1

Readers and cards...................................................................................................................... 71

6.2

Programmer and software........................................................................................................... 72

6.3

Credit Applications ...................................................................................................................... 72

6.4

Safeguards.................................................................................................................................. 73

7 Technical design data......................................................................................................................... 75

7.1.1

Housings dimensions................................................................................................... 75

ATS Designers Guide 3

7.1.2

Space in Hosings......................................................................................................... 75

7.1.3

Dimensions of devices PCB. ....................................................................................... 76

7.1.4

Control Panel and Memory configurations. ................................................................. 77

7.1.5

Current consupmtion. .................................................................................................. 79

7.1.6

Card Readers Technical Data. .................................................................................... 82

4 ATS Designers Guide

1 S

YSTEM COMPONENTS

.

1.1 Control panels

The main element of the Advisor MASTER system is the control panel. The idea behind the Advisor MASTER system is to supply a product with the best possible functional parameters for the end user, as well as for the installing technician. The control panel, as a product, is supplied as a set, consisting of:

Control panel mainboard;

• Metal housing;

• Mains power transformer;

• Mains power connector, equipped with a fuse;

• Battery connection cables;

• A set of 4k7 Ohm end of line resistors;

• User and installation manuals.

Common characteristics of the ATS system control panels:

Housing – There are three types of housing for the control panel and ATS expansions. All of them have a common characteristic set of holes and mounting points, which pattern enables the installation of every control panel type and/or other expansions and system accessories. The space allocation details for the different housing types, are contained in the appendices.

All control panels are equipped with the same switched mode power supply unit, Power unit – providing 2,2A @ 13,8V DC, enabled for buffered mode (battery back-up). The details for planning of the emergency power supply, batteries etc. can be found in chapter 2.

Mainboards – The control panels as well as other equipment parts have standardised sizes and placement of their mounting points. This enables the installation in any system housing.

Dialler –

The MI bus–

The control panel terminal blocks are detachable, which simplifies connection of the circuits.

A telephone communicator comes as standard, enabling communications with monitoring stations (CS) as well as modem connections with a PC. The baud rate is limited. The configuration details can be found in section 3.3.

The control panel can be extended with additional communications equipment via the MI bus. The available modules enable communication with CS stations via GSM or ISDN networks, as well as voice reporting. The configuration details can be found in section

3.5.

Service connection – Regardless of the type of control panel, each is equipped with a RS232 connector, allowing for service communications with the configuration program (TITAN). This connection is time-limited. For permanent connections, an appropriate expansion needs to be used.

System timer– The central unit is equipped with an autonomous Real Time Clock (RTC) circuit, synchronized via a quartz frequency generator. It ensures an exact measurement of time regardless of the CPU load, frequency of the mains power, or other external occurrences.

Alarm zones–

The systematic time correction can be set through the configuring software as –119 to

119 seconds per day.

All system inputs are processed by a A/D converter and then analysed as to their state through the control panel, or DGP processor. There are 8 or 16 alarm zone connections on the control panel mainboard. Their number can be increased using the ATS1202 expansion.

End of line resistors – The system supports three types of EOL resistors: 2k2, 4k7 and 10k. By default, the

4k7Ohm resistor is used.

Signal outputs – Each control panel has 3 high-current, monitored signal outputs, allowing the attachment of an external/internal siren or a signal lamp (beacon).


Memory – The inbuilt memory of the control panel is sufficient to support a typical, medium complexity alarm system (50 users, 250 events, 10 alarm groups). The control panel memory can be expanded using the appropriate modules.

System bus – The RS485 system bus enables the attachment of manipulators (RAS stations), as well as alarm and access control expansions. The same interface is used to connect the control panels into a network, or to the local bus of other equipment.

Expansions:

The MI bus –

Memory –

ISDN and GSM communicators, and a voice reporting module.

The control panel supports installation of one of three available memory modules. They increase the amount of users, logged events, alarm settings and access control groups supported by the system, as well as decreasing the reaction time of the system.

PC and printer interface – Enables the user to permanently connect the control panel to a PC, connect the control panels in a network to the PC and connect the control panel to a remote system for programming, maintenance and monitoring.

Alarm zones – The onboard alarm zone connectors can be expanded using the ATS1202 expansion up to a total of 32 alarm zones. Further lines are available through the use of DGP expansions connected to the system bus.

System outputs – The control panel connector supports 4 ‘OC’ outputs. By connecting a synchronous expansion card (ATS1811/20) to the output slot, the maximum relay output count can be increased to 128 and the ‘OC’ count can be increased to 256, limited by the maximum expansion module count, the available housing space, and the supplied power.

Additionally, the control panels are equipped with a NC/NO relay (not supported by the

ATS2000).

System bus – Enables the connection of 16 manipulators (RAS stations) and 15 expanders (DGP modules) allowing the use of all alarm zones and additional access control functions – elevator and door controllers.

The central unit of the Advisor MASTER system that defines its capacity, and through the availability of some expansions, its functionality is the control panel. The Advisor

MASTER system offers three types of control panels – ATS2000, ATS3000 and

ATS4000/4518. The differences between them are in the available zone quantity, and the availability of some expansions. This way, the system, regardless of its size or the control panel used provides the same functions, uses the same software, can be connected to the same equipment and a configuration created for one panel, can be freely used on all types of ATS control panels

1.1.1.1 ATS4000

16 alarm zones on board expandable to max. 32 zones;

256 zones in the system

16 independent areas

74-138 Alarm Groups

10-120 Door Groups

50-67k users

250-1000 alarm events

10-1000 access control events

M – ATS1643 housing

Programming controlled power output

Expansions:

Memory

Computer, printer interface

Communications

Input/Output

The ATS4000 control panel is the basic control panel type of the Advisor Master system.

The other central units are modifications of this device. Because of that, in the following chapters the application examples are shown using the ATS4000.

Table 1-1 Expansion modules, available for ATS4000.


Expansion Description Q-ty Size

Memory – mounted in the slot on the mainboard, only one of the following modules.

ATS1830 1Mb -

1 -

-

Computer, printer interfaces – mounted directly on the mainboard, only one of the following modules.

ATS1801

ATS1802

Computer, printer interface (two RS232 ports)

Printer interface(RS232 port)

1

B+

B+

Communications– MI bus , mounted in housing slots, below the mainboard .

1 A

2 B

1 B+

Inputs– mounted in available housing slots.

ATS1202 8 alarm zone expansion.

Outputs– mounted in available housing slots.

ATS1810 4 relay outputs.

ATS1811

ATS1820

8 relay outputs.

16 open collector outputs.

2

1

16

16

B

B

BB

B+

Table 1-2 ATS4000 housing space.

M – ATS1641 housing

Battery Capacity Free housing slots Free slots below the MBC*

BS127N 7,2Ah

2xBS127N 14,4Ah

BS131N 18Ah

4xB or 2xB+ or 2xBB

4xB or 2xB+ or 2xBB

2xB or 1xBB

6xB or 4xB+ or 2xA

*- Communication expansions can be mounted below the mainboard (Mother Board Circuit)

1.1.1.2 ATS4500 mainboard:



16 independent areas

138 Alarm Groups

120 Door Groups

11k-67k users

1000 alarm events

1000 access control events

L – ATS1644 housing


Expansions:

Memory


Communications

Input/Output

The ATS4500 control panel is equipped with the ATS4000 mainboard equipped with the basic ATS1830 1Mb memory expansion and a L – type housing. The extended memory and the larger housing, allowing the installation of more expansions, as well as a larger battery, make the ATS4500 a control panel best suited for systems providing access control.

The expansions for ATS4500 are identical with the ones for ATS4000 shown in Table

1-1, the difference being the ATS4500’s pre-installed ATS1830 memory expansion.


8

Table 1-3 ATS4500 housing space.

L – ATS1642 housing

Battery Capacity

BS127N 7,2Ah

2xBS127N 14,4Ah

BS131N 18Ah

BS129N 26Ah

2xBS129N 52Ah

Free housing slots

6xB or 3xBB or 4xB+ or

2xA

Free slots below the MBC*

6xB or 4xB+ or 2xA

*- Communication expansions can be mounted below the mainboard (Mother Board Circuit)

1.1.1.3 ATS3000



8 independent areas

74 -138 Alarm Groups

10 -120 Door Groups

50k-67k users

250 - 1000 alarm events

10 - 1000 access control events

S – ATS1642 housing


Expansions:

Memory


Communications

Input/Output

In this control panel, not all expansion combinations are available. Due to the layout of the device, it is not possible to install both the ATS1831/32 memory expansions and the

ATS1801/02 computer/printer interface.

Apart from that, the control panel is supplied in a smaller housing. This does not lead to less space for expansions, because the control panel’s mainboard is much smaller.

Table 1-4 Expansion modules, which can be installed in the ATS3000 control panel.



ATS1830 1Mb -

ATS1831 4Mb, IUM, interchangeable with ATS1801/02 1 -

ATS1832 8Mb, IUM, interchangeable with ATS1801/02 -

I Computer, printer interfaces – mounted directly on the mainboard, only one of the following modules can be installed, and not in conjunction with the memory expansions

ATS1831/32

ATS1801

ATS1802

Computer, printer interface (two RS232 ports)

Printer interface(RS232 port)

1

B+

B+


1 A

2 B

1 B+





3

1

B

B

ATS Designers Guide

Expansion

ATS1811

ATS1820

Description

8 relay outputs.


Q-ty

16

16

Size

BB

B+

Table 1-5 ATS3000 housing space..



BS127N 7,2Ah

2xBS127N 14,4Ah

BS131N 18Ah


6xB or 3xBB or 1xA

6xB or 3xBB or 1xA

4xB or 2xBB or 1xA

Free slots below the MBC*

4xB or 2xB+ or 1xA

*- Communication expansions can be mounted below the maiboard (Mother Board Circuit)

1.1.1.4 ATS2000



4 independent areas

74 Alarm Groups

10 Door Groups

50 users

250 alarm events

10 access control events

S – ATS1641 housing

Expansions:

Communications

Input/Output

The central panel does not include slots for memory expansion and computer/printer interface ATS1801 as well as a programming controlled power source. Additionally, the connector clamps in this model are fixed.

The mainboard is the same size, and is supplied in the same housing as the ATS3000.

Because of that the parameters for batteries and available expansion space are the same in ATS2000 and ATS3000 – see Table 1-5.

Table 1-6 Expansion modules, which can be installed in the ATS2000 control panel.



1 A

2 B

1 B+





ATS1811

ATS1820

8 relay outputs.


3

1

16

16

B

B

BB

B+


1.1.1.5 Comparison of most important characteristics

Table 1-7 Common characteristics of the control panels.

Parameter

Input expansions

Output expansions

Power source

Inbuilt PC communications

System bus

Inbuilt communications

Communication expansions

Time measurement

Alarm zones

End of line resistor

Value

Up to 32 zones

No limit

2,2A @ 13,8V DC

RS232 – service port

RS485

Analogue dialler

ISDN, GSM, voice module

Real-time clock circuit RTC

A/D converter

2k2, 4k7, 10k software defined

Table 1-8 Control panel characteristics.

Parameter

Onboard zones

With zone expansions fitted

System capacity – zones

ATS4500

16

32

256

ATS4000

16

32

256

ATS3000

8

32

64

ATS2000

8

32

32

Alarm groups

Door groups

138

120

70-138

10-120

70-138

10-120

70

10

Alarm event log

Access control log

IUM ATS1831/32 memory

Computer/printer interface

1000

1000

Yes

Yes

250-1000

10-1000

Yes

Yes

250-1000

10-1000

ATS1831/32 or

ATS1801/02

Housing type

Mainboard type

L

C

M

C

S

C-

*- The ATS1831/32 memory expansion is interchangeable with ATS1801/02

S

C-

250

10

No

No

Table 1-9 Important technical characteristics.

Parameter Value

Mains power supply

Max. mains power required

230VAC

58VA

Mains transformer output voltage 23VAC

PSU output voltage 13,8V DC (+/-10%)

PSU output current

Output current load:

The lamp and sirens

Relays

2,2A

1A

2A

OC type

Mainboard power consumption

Operating temperature

50mA

170mA

0-50 deg.C


1.2 User Interface

The user interface – manipulators, readers – is the only system element the user has direct contact with. It serves to inform the user of the state of the system, allow taking system control actions, and serves as a basic programming and maintenance channel for the installing technician and programmer. The Advisor MASTER system offers a whole range of RAS equipment, differing in appearance and functionality. It can also be made compatible with equipment by other manufacturers, through the use of the ATS1170

Wiegand interface.

The unique function offered by the ATS system is alarm system control – arming and disarming the alarm – through the readers and user cards. This is enabled by integrating the access control and alarm systems.

Each piece of RAS equipment can be used in the ATS system to unidirectionally control the access control passage. To ease the use of manipulators to control the doors, they have been equipped with appropriate hardware features – lock control output, door access switch (RTE) input – and software functions, through which access control on the control panel level can be provided for budget sensitive applications.

RAS stations characteristics:

Alarm system control – Arming and disarming the system is the basic function of each RAS unit. Beyond that, LCD-equipped units can serve to validate alarms, suspend zones, browse the event log etc. – the common maintenance tasks in an alarm system. It is required that there is at least one LCD manipulator present in the system configured for alarm system maintenance.

Basic programming interface – LCD manipulators are the basic programming interface for the system. It is strongly recommended that at least one LCD manipulator in the system is configured for

State LEDs – programming the system.

The RAS stations are equipped with LED diodes, which serve to display the state of the system. Commonly there are 3 diodes:

Green – Power On

Orange – unit failure

Red – alert.;

In some equipment the red diode also displays the state of the RAS station area. In that case the system state is encoded as follows:

System bus–

Alert – The diode is pulsing;

Arming– The diode is lit continuously, if any of the station’s zones is armed

Disarmed–The diode is not lit, provided all zones of the RAS station are disarmed.

The RAS units are connected via the RS485 bus – addressed and queried (polled) by the

Output–

Input– control panel. Each unit except ATS1190/92 is capable of terminating the bus.

Dedicated for controlling the execution units for control panel managed access control.

Dedicated for the exit button in access control.

Access control integration– Each unit can be used as an access control interface in control panel as well as locally in the access control DGP. Access control carried out in the control panel can use the dedicated inputs and outputs of the RAS station.

Additional equipment such as the ATS1340 – door connection box – as well as software programming capabilities – blocking the door alarm zone etc., is typical for access control.

CCTV integration – Control of a multiplexer – a DVMR/DTX recorder is accessible only through LCD manipulators.


Table 1-10 RAS device list (System Bus devices)

Product Description

ATS1100

ATS1105

ATS1110

ATS1111

ATS1115

ATS1116

ATS1155

ATS1151

ATS1156

ATS1190

ATS1192

ATS1170

Keypad, 2*16 characters LCD/8 zone LEDs

Keypad, 2*16 characters LCD /8 zone LEDs with

Wiegand reader interface.



Keypad, 2*16 characters LCD/16 zone LEDs with inbuilt ATS card reader.


Outdoor, vandal-proof keypad (metal), 3 diodes, detached electronics

LED keypad (3 diodes) in metal housing, no LCD

LED Manipulator (3 diodes) in metal housing with

ATC600 magnetic card reader (no LCD)

Proximity reader (does not require an interface)

High resistance proximity reader (does not require an interface) indoor/outdoor

Wiegand reader interface (single door controller) –

PCB B+

1.2.1.1 ATS1100/05

User interface

Alarm x

AC x

Prog. x x x x x x x x x x x x x x x x x x x x x x x x x x x x

LCD 2x16 characters

8 area state display diodes

3 system state diodes

4 programmable function keys

Opening and pry-off tamper alarm

ATS1105 contains a Wiegand equipment interface.

Dimensions (LxHxD, mm): 168x126x40

The ATS1100/05 unit is one of the most basic RAS stations of the ATS system, granting access to all control, management and programming functions of the system. The limited amount of diodes does not allow display of the status of all areas at once on a single device. By choosing (using a DIP switch) the area range for display, the manipulator can be configured to display zones 1-8 and 9-16. Like all RAS devices the ATS1100/05 has an input port for the exit button, and an output port for door lock control from the control panel. Additionally, the ATS1105 is equipped with a Wiegand reader interface. It enables the connection of such a reader without installing an additional Wiegand interface –

ATS1170.

The device address as well as bus termination, and other functions for example: keyboard and display backlight, can be set using DIP switches. The connector clamps and the DIP switches can be found after removing the unit’s cover.


1.2.1.2 ATS1110/11

LCD display 2x16 characters ATS1110

LCD display 4x16 characters ATS1111

16 area state diodes


Pry-off tamper alarm

Dimensions (LxHxD mm): 92x165x25.4

(closed cover)

The ATS1110/11 unit is one of the most basic RAS stations of the ATS system, providing, through the LCD display, access to all system functions. The design of the unit enables access to connector clamps and the DIP switches without opening the device housing.

The manipulator is attached to the surface via a metal plate. Assembling device on the mounting bracket, using only one screw. This is a major simplification of the installation process.

The DIP switch serves to set the device address and to set the bus termination. Other settings (diode light settings, LCD backlight, output control etc.) are set via the control panel programming menu.

1.2.1.3 ATS1115/16

LCD Display 2x16 characters ATS1115

LCD Display 4x16 characters ATS1116

16 area state diodes


Pry-off tamper alarm

Dimensions (LxHxD mm): 92x165x25,4

(closed cover)

This is an advanced product, containing an integrated ATS Smart Card reader. The integration allows the device to use only one bus address instead of two. The access control function ”Card and PIN” of the ATS1250 can be provided by one device.

The LCD display provides access to all system functions. The design of the unit enables access to connector clamps and the DIP switches without removing the device switches.

The manipulator is attached to the surface via a metal plate. Assembling device on the mounting bracket, using only one screw. This is a major simplification of the installation process.

The DIP switch serves to set the device address and to set the bus termination. Other settings (diode light settings, LCD backlight, output control etc.) are set via the control panel programming menu.

1.2.1.4 ATS1155


1 area state diode*

Tamper switch input

Detached keyboard and electronics.

Dimensions (LxH, mm): 118x75

*- the red state diode serves to display the RAS station area state as well.


14

The ATS1155 keyboard is a solution for areas with high risk of vandalism. The metal, damage resistant keyboard and the electronics part of the device are mounted separately. Additional system state diodes can be mounted separately as well. The set consists of the keyboard, a PCB board and connection cables.

The address and bus termination are set using a DIP switch.

1.2.1.5 ATS1151/56


1 area state diode*

Inbuilt magnetic card reader (ACT600 cards)

Opening and pry-off tamper alarm

Metal cover

Suitable for outdoor use

Dimensions (LxHxD mm) ATS1151: 96x67x28



The cover design has been proven in the ACC series access control systems from

Aritech. The design, as well as a heater integration option, enables the unit to be installed outdoors even in low temperatures.

1.2.1.6 ATS1190/92

2 system state diodes (programmable)

Reader configurable via a proximity card, or internal programming menu.

Optical pry-off tamper alarm

Suitable for outdoor use

Vandal-proof design

RS485 or Wiegand interface, automatically detected



Due to its characteristics and price, the ATS1190/92 is a very attractive solution for small to medium systems. A synthetic, water-proof resin that fills the housing makes the unit resistant to damage, as well as severe weather conditions.

Compatible with:

ATS147x cards

ATS1621 programmer

Additional accessories for the ATS1190 Reader are replaceable covers in white, red, grey, beige and black.

1.2.1.7 ATS1170

2 reader state diodes

Tamper input

Wiegand or Clock-Data reader interface

Door lock relay output

Supports autonomous mode for 20 cards

Dimensions: B+

Wiegand type card reader interface used to connect readers from other manufacturers and systems to the ATS system. This unit supports autonomous mode, independent of

ATS Designers Guide

the control panel. To prepare the unit for that mode, the unit has to be programmed with up to 20 user cards. The programming interface is accessible locally via setting the appropriate DIP switches.

1.2.1.8 Listing of the most important parameters

Table 1-11 Listing of the RAS stations characteristics.

Parameter

Display 2x16 4x16 2x16 4x16 - - - - - -

State 3 3 3 3 3 3 3 3 3 2 2 2

8 8 16 16 16 16 1* 1* 1* (1) (1) -

Yes

Bus - Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes


SC – SmartCard – ATS SmartCard reader

MC – MagneticCard – ACT600 Magnetic card reader

Table 1-12 Relevant technical parameters.

Parameter

Max cons.. 165 45

Power 32

Operating voltage

Min voltage 7.19 7.25

86 34 39 70

10.5 – 13.8 V DC

29 65

OC output load

7.4

50mA (12VDC)

IP30

7.35 9.6 7.99

1A*

IP30 IP30 IP30 IP54 IP54 - IP30

Temp. max. o

C 50

Temp. min. o

C 0

50

0 -25 0 -35 0

*- max. load of the relay connectors


1.3 DGP Expansion modules

The DGP expansion modules are system bus devices and are designed to expand the system capabilities. The main task of the DGP is to connect faraway alarm zones, providing a local power source and system outputs. The DGP idea encompasses also access control expansions that enhance the system’s functionality in its work area.

Distributed intelligence philosophy allows systems configured from DGP and RAS devices to cover a wide range of most complicated applications.

1.3.1.1 ATS1201 alarm zone DGP

8 alarm zones on board

32 alarm zones when maximally expanded

8 OC type outputs

16 outputs when maximally expanded.

High–current, monitored siren output

Integrated switched mode power supply 2,2A

Auxiliary battery back-up


A type mainboard

The basic DGP device, providing remote ATS zone handling. Full support of the selected area is provided by the integrated power supply (2A) with battery back-up feature, a housing big enough to hold additional expansions, and an option of controlling a siren.

Note that this device allows the alarm system to take advantage of the whole range of alarm zone addresses.

The configuration of the device is done via correct setting of the DIP switches.

Table 1-13 DGP ATS1201 compatible expansion modules:

Expansion Description

Inputs – installed in available housing slots

ATS1202 8 alarm zone expansion

Outputs – installed in available housing slots

ATS1810 4 relay outputs

ATS1811

ATS1820

8 relay outputs


Amt.

3

2

2

1

Size

B

B

BB

B+

Table 1-14 DGP ATS1201housing space



BS127N 7,2Ah

2xBS127N 14,4Ah

BS131N 18Ah


8xB or 4xBB or 4xB+

8xB or 4xBB or 4xB+

4xB or 2xBB or 2xB+


1.3.1.2 ATS1203 alarm zone DGP

8 alarm zones on board

32 alarm zones when maximally expanded

8 OC type outputs

32 outputs when fully expanded.

High – current, monitored siren output

Integrated switched mode power supply 3A



A new advanced DGP device, the ATS1203 provides support for a remote ATS area. Full support of the selected area is provided by the more powerful integrated power supply

(3A) with battery back-up feature, a housing big enough to hold additional expansions, and an option of controlling a siren. Note that this device allows the alarm system to take advantage of the complete range of alarm zone addresses.

In contrast to ATS1201 all device settings are configurable remotely via a control panel programming menu, or using the TITAN software.

Table 1-15 DGP ATS1203 compatible expansion modules

Expansion

Inputs – installed in available housing slots

ATS1202 8 alarm zone expansion



ATS1810

ATS1820

8 relay outputs

Description


Amt.

3

2

4

2

Size

B

B

BB

B+

Due to the fact that both the ATS1203 and ATS1201 come in an identical housing, and the dimensions of their circuit boards are the same, the parameters for configuring the batteries and additional housing space are the same for both models, and can be found in Table 1-14.

1.3.1.3 ATS1210/11/20 alarm zone DGP

8 onboard zones – 4 for zones on ATS1220

8 OC outputs

16 outputs when fully expanded (lack of housing space)

Power supply: 12V DC

ATS1210 – metal housing – ATS1643

ATS1211/20 – plastic housing – ATS1644

Dimensions: B+

This module is supplied with power directly form the system bus, or an external power source – the power supply planning details are outlined in chapter 2. The housing supplied with the units don’t provide space for any expansions. Any output expansion plans must be preceded by a housing replacement.


Table 1-16 ATS1210/11/20 DGP compatible expansion modules

Expansion Description



ATS1810

ATS1820

8 relay outputs


1.3.1.4 ATS1230 Wireless devices DGP

Amt.

2

4

2

16-32 programmable channels/Wireless devices

Device learning function

Operating Frequency: 433MHz


Lack of bus terminator

Dimensions (LxHxD mm):

Housing: plastic

Size

B

BB

B+

18

The device is suitable for locations inaccessible by standard wired solutions. A wide range of wireless devices – transmitters – detailed in the table below shows that this product can support all security related tasks. The only difficulty is the lack of the bus terminator, meaning the maximum distance of the ATS1230 module from the control panel is 300m. For larger distances, an additional terminating resistor needs to be used.

The data bus details are provided in section 3.1.

Table 1-17 DGP ATS1230 compatible list of transmitters.


RF320I4 Wireless magnetic sensor (or a transmitter for a wired sensor – type NO/NC), sabotage

RF352I4

RF354I4

RF356I4

RF360I4

Remote control, keyfob 2 buttons


Wireless panic button in form of a wristwatch.

Water resistant wireless panic button, belt clip or neck leash.

RF425I4

RF425I4PI

RF572NSTI4 Wireless optical-thermal smoke detector, sabotage alarm, internal siren

RF620I4 Wireless inertia and magnetic sensor, sabotage alarm, white

RF620I4B

Wireless PIR sensor, EV425, 9/16m, 9 screens, opening and tear-out sabotage alarm

Wireless PIR sensor, EV425, 9/16m, 9 screens, opening and tear-out sabotage alarm, PI version

RF903I4

RF900I4

Wireless inertia and magnetic sensor, sabotage alarm, brown

Wireless glassbreak detector, acoustic, plaster mounted, sabotage alarm

Diagnostic wireless sensor testing kit, 433MHz.

Range m

300

150

150

150

300

300

300

300

300

300

300

300

ATS Designers Guide

1.3.1.5 ATS1290 addressable devices DGP.

32 Point ID ® addressable devices

32 system outputs

PID bus learning mode


This new device in the Advisor MASTER system allows the use of the local communications bus interface of the DGP module to connect sensors to the alarm system. To communicate with the devices, an open architecture Point ID ® interface is used. The bus planning details, recommended wiring etc. can be found in section 3.2.2.

In addition to the DGP module a whole range of, Point ID compatible, devices is available, and listed in the table below.

The device can be programmed via the remote device menu. The DIP switches serve only to supply the DGP module address, and to activate the bus terminator.

The use of addressable sensor technology significantly reduces the cost of system wiring by simplifying it, reducing the installation time, the amount of materials used etc.

Table 1-18 List of available Point ID devices


SI-AD

AD011

AD044

Universal, single input Point ID module

Universal Point ID module, 1I/1OC

Universal Point ID module, 4I/4O, monitored, externally powered, relay outputs

AD111 Point ID module, 1I/1OC installable inside the sensor.

AP750-AD

EV435-AD

PIR sensor, range: 15,2m; 7 curtains;

PIR sensor, 9/16m, 9 curtains, Point ID interface

EV435AM-AD PIR sensor, 9/15m, 7 curtains, antimasking,

Point ID interface

Inputs Outputs

1

1

0

1

4(+4) 4

1 1

1

1

1

1

2 2

1.3.1.6 ATS1250 4 door Access Control DGP

4 bi-directional passages

4 direct Wiegand reader inputs

16 remote readers on the local bus

16 onboard alarm zones

4 door lock control relay outputs up to 48 additional outputs

Advanced access control functions

48 macrodefinitions

Full local copy of the user database

Autonomous operation mode

Integrated 4,5A switching mode power supply


L type housing

Dimensions: D

A 4 door controller provides advanced access control functions for the users of the

Advisor MASTER system. The device has been designed to work independently of the control panel unit. The autonomy of the controller is assured by a full local copy of all the system settings, including both user and card databases. Additionally the equipment has been designed to directly control locks, entry buttons (RTE), readers, door and lock alarm zones, tamper alarms etc. This ensures, that even when communication problems with the control panel occur, the controlled passages will function flawlessly. Communications with the control panel is not necessary for proper functioning of the passages, although the available DGP mainboard inputs, dedicated to access control tasks, can be


20 programmed to act as alarm zones of the alarm system. The readers and access control keyboards of the ATS1250 DGP can be used to the alarm system control functions.

Configuration details using the ATS1250 device can be found in section 4.4.2.

Table 1-19 DGP ATS1250 compatible expansion modules

Expansion Description Amt. Size


ATS1830 1Mb – pre-installed -

1 -

-

Outputs– mounted in available housing slots


ATS1811

ATS1820

8 relay outputs

16 open collector outputs

2

6

3

B

BB

B+

Table 1-20 DGP ATS1250.housing space

Battery

L – ATS1642 housing

Capacity

BS127N 7.2Ah

2xBS127N 14.4Ah

BS131N 18Ah

BS129N 26Ah

2xBS129N 52Ah


6xB or 3xBB or 4xB+

1.3.1.7 ATS1260 4 lift Access Control DGP.

4 elevators (lifts)

64 elevator floors

4 direct Wiegand reader inputs

16 remote readers on the local bus

15 local DGP (256 zones – one for every floor in each elevator)

16 dedicated onboard inputs

4 relay outputs (expandable to 256)


48 macrodefinitions

Full local copy of the user database

Autonomous operation mode

Integrated 4.5A switched mode power supply


L type housing

Dimensions: D

The lift controller was based on the ATS1250 4-door controller hardware. The device is supplied as a set ATS1250+ATS1260UP – a lift controller software and instruction manual package and the ATS1250. Because of that, the available space details in the

ATS1260 housing, are identical with those of ATS1250, detailed in Table 1-20.

Contrary to the ATS1250 the elevator control DGP requires installation of additional local

DGP modules in order o achieve the maximum amount of 256 floor request inputs

(4 elevators x 64 floors), and 256 outputs for visualization of the selected floors. The

ATS1260 DGP is compatible with every alarm zone DGP of the ATS system, and every

RAS station of the ATS system, see Table 1-10), using the ATS1170 and the IUM function with every Wiegand interface reader, and 48-bit cards. The local bus design procedure has been outlined in section 3.2.1.

Table 1-21 ATS1260 DGP compatible expansion modules.

ATS Designers Guide

Expansion Description Amt. Size


ATS1830 1Mb – preinstalled -

1 -

-



ATS1811

ATS1820

8 relay outputs.


1

16

16

B

BB

B+

1.3.1.8 Listing of the most important parameters.

Table 1-22 DGP device list (RS485 bus devices)

Product

ATS1201

ATS1203

ATS1210

ATS1211

ATS1220

ATS1290

ATS1230

ATS1250

ATS1260

Description

8 zones (max.32) and 8 outputs (max.16) expander, integrated 2A power supply, M type housing

8 zones (max.32) and 8 outputs (max.32) expander, integrated 3A power supply, M type housing

8 zones and 8 outputs expander, plastic housing (ATS1644)

8 zones and 8 outputs expander, metal housing (ATS1643)

4 zones and 8 outputs expander, plastic housing (ATS1644)

32 addressable sensors expander

433MHz wireless device receiver (up to 32 sensors and 16 remotes), plastic housing

4-doors access controller, integrated 4,5A power supply, L type housing

4-elevators (64 floors) controller, set of ATS1250+firmware, requires additional DGP modules

Table 1-23 Listing of the alarm zone DGP characteristics

Parameter ATS1201 ATS1203 ATS1210/11 ATS1220 ATS1230 ATS1290

Max. zones q-ty

Onboard outputs

Max. outputs q-ty

Siren output

Power supply

32

8 OC

16

Yes

32

8 OC

32

Yes

230V AC 230V AC

8

8 OC

16**

-

12V DC

ATS1644

*- addressable and wireless devices

**-output expansions possible only after replacing the housing

4

8 OC

16**

-

32*

-

-

-

32*

32*

32*

-

12V DC 12V DC 12V DC

ATS1643 Plastic ATS1644

104x132x27


Table 1-24 Listing of the access control DGP characteristics

Parameter

Number of passages

Number of onboard reader IF

Max. number of readers

Local DGP q-ty

Onboard zones

Max. onboard zones

Max. zone quantity

Onboard outputs

Max. output quantity

Siren output

Power supply

ATS1250

4 doors

4

16

-

16

16

16

4 relay.+ 8 OC

48

Yes

230V AC

ATS1260

4 lifts/ 64 floors

4

16

15

16

16

256

4 relay. + 8 OC

256

Yes

230V AC

Circuit board size A A

Parameter

Table 1-25 DGP technical characteristics

ATS1201 ATS1203 ATS1210/11 ATS1220 ATS1230 ATS1290 ATS1250/60

Avg. Power cons.

Operating voltage

Min. voltage

Power supply unit

75 75

230V AC 230V AC

±10%

2A

±10%

3A

50

12V DC

45 30 53

12V DC 12V DC 12V DC

10.5V DC 10.5V DC 10.5V DC 10.5V DC

- - - -

275

230V AC

±10%

4,5A

OC output load 50mA 50mA 50mA 50mA - - 50mA

Relay contacts load 1A@30V 1A@30V 1A@30V 1A@30V - - 1A@30V

Door lock relay load

Temp. max. o C

Temp. min. o C

- - - - - - 2A@30V

Humidity

1.4 System accessories

ATS1202

ATS1810

ATS1811

ATS1820

ATS1821

1.4.1.1 System input and output modules.

8 alarm zones.

Used for control panel and DGP expansion

Dimensions: B

4 relay outputs. Asynchronous device, not compatible with remaining output expansions. This module converts OC outputs into relay outputs.

Dimensions: B

8 relay outputs. Synchronous device, enabling cascade linking to provide additional outputs.

Dimensions: BB

16 OC outputs. Synchronous device, enabling cascade linking of modules.

Dimensions: B+

8 OC outputs. Synchronous device, it’s not possible to cascade link the modules.

Dedicated module for communications with external communicators not integrated with the ATS system..

Dimensions: B


1.4.1.2 Alarm communicator modules.

ATS7200

ATS1801

ATS1740

ATS1741

ATS1742

Connected to the control panel through the MI bus

Supports all ATS reporting functions

Uses standard protocols (SIA, CID, etc.)

Supports all ISDN configurations

Allows remote connections to the TITAN software

In case of a reporting need, takes control over the ISDN line.

Dimensions: A

Voice reporting module.


Supports voice reporting through all communication channels.

Total message duration 35sec.

8 voice messages (including greeting)

Flexible mapping of voice messages to events.

Up to 2 modules can be installed in the control panel.

Dimensions:: B+


Supports all ATS reporting functions

Uses standard protocols (SIA, CID, etc.)

Has an unique network delay adaptation function.

Network signal monitoring

External antenna

Integrated GSM phone module

Dimensions: B+

1.4.1.3 Computer and printer communication modules.

Computer and printer interface

The device provides two RS232 ports for the computer and printer each.

The printer port is unidirectional, and serves to send the events to a serial printer and to integrate the ATS system with CCTV systems that use DVMR digital recorders.

The computer port serves to directly, or remotely connect to a PC without time limits with a broaden bandwidth (4800bps)

Module connects directly do the mainboard, does not use housing expansion slots.

Dimensions:: B+

This device provides one RS232 printer port.

The printer port is unidirectional, and serves to send the events to a serial printer and to integrate the ATS system with CCTV systems that use DVMR digital recorders.

Module connects directly do the mainboard, does not use housing expansion slots.

Dimensions: B+

1.4.1.4 RS485 bus accessories.

Bus amplifier/isolator. Provides the RS485 bus signal amplification and galvanic insulation of the bus branch up to 1.5kV. Increases the range of the bus and allows implementation of complex RS485 bus networks.

Dimensions: B

Bi-directional RS485 – RS232 converter. The device converts bus signal for modem communications, and for linking control panels in a network.

Dimensions: B+

Loop interface. Allows creation of a RS485 bus loop.

Dimensions: BB


ATS1743

ATS1830

ATS1831

ATS1832

Fibre-optical converter. Converts the RS485 signal into optical signal, allowing the use of optical fibres in data bus construction.

Dimensions: B

Parameters:

Wavelength: 820nm

Optical fibre: 62,5/125um multimode

Converter: LED

Flux budget: 15dB

AGC: none

The ATS system has three memory modules:

1Mb memory module.

4Mb memory module, hardware IUM.

8Mb memory module, hardware IUM.

Functional details, and guidelines for choosing the right module are described in control panel configuration, section 4.1.

1.4.1.6 ATS system Wonder-Box housing

The ATS system housing provide a standard set of mounting points, which makes them compatible with every expansion. The expansions have standardised circuit board sizes.

Because of that, they fit exactly into the housing slots, which can be flexibly used to build the system. Detailed information concerning the housing, the free space inside etc. can be found in the appendices at the end of this document.

ATS1340

ATS1621

ATS1630

ATS1631

ATS1632

Door connection box.

Provides connectors for: a reader, an exit button, a door lock device, external power supply and the data bus..

Is equipped with lock control relays

Smart card programmer

RS232 temporary service connection cable

ATS18xx and ATS1202 expander connection cable

ATS1801 RS232 direct connection cable


1.5 ATS8100 – TITAN Software

The TITAN system provides a simple, Windows ® compatible interface, which simplifies programming of the Advisor MASTER system control panel.

A PC with a working TITAN system can be connected to the control panel either remotely

(via the inbuilt PSTN communicator), or locally (through a RS232 connection). The

RS232 connection can be time-limited (60 min) – if the inbuilt RS232 port is used – or permanent if an optional ATS1801 computer/printer interface is used. In any mode the

TITAN system can retrieve and store the whole database or just one setting at a time.

The TITAN system can be used to make backups, and store archive copies of the data from 9999 independent systems on one PC. Each system can consist of 1024 control panels using the same user database.

1.5.1.3 Reports

An efficient report printing function makes it possible to create detailed programming sheets for all the system information contained in the TITAN database. This provides help in quick fault removal, system expansion, programming and maintenance. It provides the option of generating a large number of customised log reports. The reports can encompass any combination of date/hour ranges, manipulators, users and other parameters. ATS Smart Card programming, can be done in place, using the TITAN system in conjunction with an optional card programmer.

Every ATS control panel, can be subjected to diagnostic sessions by the TITAN system, which gathers the reports. The parameters verified by the diagnostic software conform to the EN50131 standard and encompass analogue signal measurement such as input loop resistance as well as voltage and supplied current for all RAS stations and DGP modules connected to the data bus.

1.5.1.5 Zone maps

Alarm map images (floor diagrams or drawings) can be configured to provide detailed information for any zone in the system. In case of zone activation, the information is displayed on the map, which enables the operator to manually control the alarm on the map. To simplify the TITAN system operation, a ”Point & Click” interface has been implemented, using a context menu. All alarm events can be handled from the map level, and not only from the ALARM menu. Several operators can use the same TITAN system, each having appropriate access privileges, and being subjected to specific restrictions.

1.5.1.6 Real-time event logging

The real-time event log contains all triggered events, along with the date, hour, and event description. The information is then stored in the history database, which can be archived, reported and displayed as a permanently visible window.


The TITAN system provides a fully integrated Photo ID solution, which allows creation of user, guest or client identification cards with their photo. The photographs can be captured from a camera video stream, or imported in digital format. The TITAN system enables design and priming of any user card sets either with detailed information about the company and user (taken from the database), or without.

1.5.1.8 Control panel network monitoring

The TITAN system can support up to 16 COM ports simultaneously. Each COM port can support up to 16 ATS control panels. In total there can be 64 systems connected to the

TITAN software at the same time. Each control panel is an independent security system that reports to a single TITAN system.

1.5.1.9 ATS8100UP – Update

The software is provided in two versions – full and update. That way users of older versions of the software can easily extend their systems with new features. The UP version has a full range of database tools, and can, if needed, update and repair existing databases without the need to import them after finishing the update.

1.5.1.10 Licence

In Poland the TITAN software is distributed free of charge, and the associated royalties are included in the price of the control panel modules necessary to use the system’s functions. Nevertheless all licence provisions hold their power – see software appendix.

Table 1-26 Technical characteristics

Parameter Value

System requirements: Windows OS( 95/98, NT, 2000 or XP

Processor: Pentium 166 or better

32 MB RAM

100 MB free hard drive space

CD-ROM drive and mouse

1 (TITAN is single workstation software)

64

Maximum number of connected PC’s

Maximum number of simultaneously connected control panels

Maximum number of control panels in the system:

1024

Maximum number of systems in the database: 9999 systems

Maximum number of printers: Dependant on the number of assigned ports

Communication ports in the PC:

Recommended connection cable for

ATS1801:

Recommended cable for the inbuilt RS232 port:

Maximum wiring length for RS232:

Serial ports installed in the system (max. 16)

4-wire shielded RS232 data cable (not twisted pair)

ATS1630 (RS232 active cable)

15 metres


2 S

YSTEM POWER SUPPLY

.

In every security system, the power supply design is an essential part. Providing the equipment with adequate working conditions in critical situations is vital for building security. Below are some of the critical aspects of the power supply problem, pertaining to system design:

• Power supply efficiency;

• Backup power – batteries and their recharging;

• Power requirements of the equipment;

• Power transmission losses;

• Shielding and grounding.

Due to the area covered, and projected flexibility the Advisor MASTER system offers a distributed power supply system. The control panels, as well as the DGP (alarm and access control) are equipped with a switched mode power supply with current draw ranging from 2.2A to 4.5A (13.8V DC). Each device is designed to provide backup power, and to supply equipment connected directly, or through the system bus. This ensures the alarm system is constantly supplied from a local power source, connected to the central unit only through the data bus.

Each ATS system power supply is equipped with a backup power system. The batteries are charged from the main power supply. Because of that, it is necessary to secure a proper margin of power supply current draw to enable recharging of the batteries appropriately fast enough for system security level.

A unique feature about the ATS equipment is verification of not only the presence of a battery, but also its condition. During the battery test, the system switches to battery power for a while, checking how much power it drains from the battery (it measures the voltage drop, current and time). After restoring the mains power supply, the system verifies the amount of energy necessary to restore the battery to its starting state

(measuring the voltage, current and time). Based on the gathered data, the system verifies battery life and, if necessary, sends an appropriate service report. The event log will of course contain the appropriate entries.

Another feature of the Advisor MASTER system power supply is a battery deep discharge protection, which ensures the batteries do not get broken by complete discharge. During a longer period of operating on battery power, if the supplied voltage drops below a certain level, the system goes into a suspended state after sending the appropriate reports to a SMA station and logging the appropriate entries in the event log. When the main power supply becomes available again, the system will restore itself to full functionality, send the appropriate reports to the SMA station and log the appropriate entries in the event log.

2.1 System power supply

The system power supplies are available in the control panels, the ATS1201/03 basic system DGP and ATS1250 Access control DGP. The use of a system power supply is recommended whenever possible, due to the advanced power supply monitoring functions and the capability of testing the batteries. The power requirement data for the equipment does not include the power requirements for expansions and other system devices connected to them. The average values are given for equipment in stand-by mode – normal zones state etc. The peak values pertain to the system in alarm state – shorted zones, increased data bus communications etc. but do not include power requirements for signal outputs, and other devices supplied by the system. The power supply design should provide adequate supply for those devices. To simplify the definition of power requirements, the following lists have been assembled:


Table 2-1 Power supply efficiencies, and power requirements.

Device

PSU

Current

Draw

Current consumption

Max. Average

Comment

ATS1250 4.5A 275mA 275mA Access control device.

To simplify the work of the designer, we gathered data for the typical power supply and battery configurations and placed them in the table below (Table 2-3). The assumption for the evaluation in Table 2-3 is system security level 3 and 4 – The system is supplied in stand-by mode for 60 hours, and the batteries are recharged to 80% capacity in less than

12 hours (EN50131).

The battery configurations listed by housing and equipment size are gathered in Table

2-2.

Table 2-2 Battery configurations for Advisor MASTER devices.

Housing ATS1640 ATS1641 ATS1642 ATS1642 Battery capacity

Device ATS2000 ATS4000 ATS4500 ATS1250

Battery

Configurations

ATS3000 ATS1201

ATS1203

ATS1260

BS127N

BS130N

BS131N

x x x x 7.2Ah x * x *

x x 10Ah

x x 18Ah

2xBS127N

BS129N

2xBS129N x x 14.4Ah

x x 26Ah x

*- lack of expansion space underneath the control panel/DGP mainboard

52Ah

Recommended configurations x x x x x

Table 2-3 Security level 3 and 4 equipment power supply.

Device

Battery

Ah

Device power consumption mA

Additional load mA

Charging current mA

ATS2/3/4018 18 200 85 1715

ATS1201 7,2 75 39 1880

18 75 210 1710

25 75 320 1600

ATS1203

ATS4500

7,2 75 40 2685

18 75 220 2500

25 75 330 2395

18 200 85 1715

25 200 200 1600


2.2 System equipment power consumption.

Devices equipped with a power supply – control panels, and some DGP – have safety measures which prevent excessive battery discharging, switching them off if the voltage drops below 10.5V. For other devices, the minimum voltage required to operate correctly has been gathered in table Table 7-9 placed in the last chapter of the manual. The values for equipment connected to devices equipped with a power supply are only for orientation purposes.

Some devices have characteristic current consumption values depending on the connected equipment. In the table below the current consumption is given for the device with connected equipment. A detailed list of device parameters in different working conditions are given in chapter 7 of the manual in table Table 7-9.

Table 2-4 Characteristic power requirements for the ATS devices.

Device Connected equipment

Description

ATS1100 - Keypad, 2*16 characters LCD/8 zone LEDs

Keypad, 2*16 characters LCD /8 zone LEDs with

Wiegand reader interface.

ATS1105 manipulator with a magnetic card reader connected

ATS1110

ATS1111

-

-



Keypad, 2*16 characters LCD/16 zone LEDs with inbuilt

ATS card reader.

Keypad, 2*16 characters LCD/16 zone LEDs with inbuilt

ATS card reader.

ATS1151 - LED keypad (3 diodes) in metal housing, no LCD

Current con. mA

Max. Average

185 73

185 78

195 150

95

95

32

32

165 86

169 86

45 34

Outdoor, vandal-proof keypad (metal), 3 diodes, detached electronics

70 70

ATS1170

ATS1170+

ATS1190

High resistance proximity reader (does not require an interface) indoor/outdoor use

ATS1202

ATS1210/11

ATS1210/11+ ATS1810 ATS1210 with 4 relay outputs module connected

ATS1210/11+ ATS1811 ATS1210 with 8 relay outputs module connected

ATS1210 with 16 open collector outputs module connected

ATS1220

ATS1230

ATS1290

ATS1740

ATS1741

ATS1742

ATS1743

ATS1810

ATS1811

ATS1820

-

ATS1190 Interface with a proximity card reader connected.

-

-

-

-

-

-

-

-

-

-

-

-

-

ATC600 magnetic card reader

Wiegand reader interface (single door controller) – PCB


8 zones module for expander and control panel- PCB

8 zones and 8 outputs expander

4 zones and 8 outputs expander

433MHz wireless device receiver

Point ID addressable sensor expander.

Isolator/ RS485 bus repeater - PCB

RS485 / RS232 bus converter- PCB

RS485 bus loop interface – PCB

Fibre-optical bus converter- PCB

4 relay NO/NC outputs module – PCB

8 relay NO/NC outputs module – PCB

16 open collector outputs module – PCB

45 39

10

53

130

225

45

95

50

32

65

29

50 29

9

50

70

110

90 38

53

154

90

100

86

60

60

170

50

45

39

50

60

100

86

36

1

20

20


Device Connected equipment

Description Current con. mA

Max. Average

ATS1801

ATS1802

ATS1830

-

-

-

Control panel RS232 computer/ printer interface (2 ports) 60

Control panel RS232 printer interface 60

ATS3000/4000 control panel 1MB memory expansion

ATS4000/4500 control panel and ATS1250 controller

4MB Intelligent User Memory.

30

20

20

3

30 10

ATS4000,4518 control panel and ATS1250 controller

8MB Intelligent User Memory.

ATS7100

ATS7200

-

-

ISDN communicator module, B channel

30 10

92

ATS Master control panel voice module (2+6 messages) 50

45

23

ATS7300

ATS1410

-

-

GSM communicator module

Magnetic card reader

110 20

75

Several examples of power requirement calculations for expanded devices.

Table 2-5 Expanded ATS3000 control panel power requirements.

Device Description Current consumption mA

Comment

ATS3000 Control panel 8 zones(max.64), 8 areas, with a dialler, S type power supply housing

Max. Average

Maximum current for all zones shorted

Connected equipment

ATS1202 8 inputs module for expander and control panel- PCB


ATS1801 Control panel RS232 computer / printer interface (2 ports)

ATS1830 ATS3000/4018 control panel 1MB memory expansion

ATS1811 8 relay NO/NC outputs module for control panels and expanders

ATS1201 – PCB

Additional equipment total: 160

10 9

10 9

60 60

One port active

30 1

50 20

99

Together with the control panel: 410 269

Table 2-6 Expanded ATS4000 control panel power requirements.

Device

ATS4000

ATS1801

ATS1830

Description Current consumption mA

Comment

Control panel 16 zones (up to 256), 16 areas, with a dialler, M type power supply housing

Max. Average

250 200


Control panel RS232 computer/ printer interface (2 ports)

ATS3000/4018 control panel 1MB memory expansion

Additional equipment total:

60 60

One port active

30 1

90 61



Table 2-7 Expanded ATS4500 control panel power requirements..


Max. Average

ATS4500

Control panel 16 zones (up to 256), 16 areas, with a dialler, L type power supply housing

250 200





ATS1201 – PCB


ATS1201 – PCB

ATS1831 ATS4000,4518 control panel and

ATS1250 controller 4MB smart memory module.

ATS1801 Control panel RS232 computer/ printer interface (2 ports)

ATS7100 ISDN communicator module, B channel


10 9

10 9

50 20

50 20

30 10

60 60

330 178


Table 2-8 Expanded ATS1201 DGP power consumption.


Max. Average

ATS1201 8 Inputs (max.32) and 8 outputs

(max.16) expander, M type power supply housing

120 75






ATS1201 – PCB


ATS1201 – PCB


Together with the control panel:

10 9

10 9

10 9

50 20

50 20

130

250

67

142

Comment

Comment


2.3 Wiring.

The proper grounding and isolation of the devices is an important issue in each wide area system. All the system elements are equipped with a grounding connector, and should be connected to a common grounding point in the central station via a 2.5mm

2

wire. The data bus shield should be connected to common ground on one end only. The data shield should not under any circumstances be grounded on both ends of the transmitting wire.

The design should plan to include appropriate power supply wiring including a grounding wire connected to all devices that require it. To separate a part of the system galvanically the ATS1470 isolating module has to be used, as it provides insulation up to 1.5kV. Using the module you have to remember that it needs to be connected to system grounding on the side it’s powered from.

The powering elements further away than 100m from the control panel or a power supply- equipped DGP, needs to be laid separately from the data bus. Having the power supply alongside the data bus can lead to voltage dropping below 10.5V which can hamper system stability. A further limit is the maximum current load (1A) of the power output.

2.4 Connecting other power supplies.

When planning to connect another power supply, you have to ensure the proper connection to the system grounding and not connect the positive connectors to any other power supply. The system power supply in emergency situations requires that additional power sources ensure an adequate supply in case of mains power failure. For systems with higher security levels, the power supply needs to fulfil certain criteria of back up power duration and subsequent recharging of the batteries. Examples of calculations can be found in section 2.1. A further requirement is monitoring the mains power. For that, you need to provide one alarm zone, which will be activated in case of mains power failure. Drawing 2-1 shows an example of connecting an external power supply to the

ATS system. A 2A @138V DC power supply with battery backup is used. It is supplied with a transformer and housing, in which a BS127N(7.2 Ah) or BS130N(10Ah) battery can be installed. The power supply can also be installed in an empty ATS housing and use a bigger battery, but the power supply circuit board is not compliant with the ATS mounting holes standard.

Mains power monitoring zone

ATS device with a power supply

+ -

32

BU4

PG822

Other devices

Drawing 2-1 Connecting the PG822 power supply to the ATS system.

ATS Designers Guide

3 C

OMMUNICATIONS

The alarm and access control system has extended communication capabilities. Viewed globally, the communications, that is, the bi-directional data transmission, should be divided into two aspects: system internal communications, and communications between the system and the outside world – reporting events to monitoring stations.

System internal communications (Drawing 3-1) has been divided into 3 basic parts:

• Control Panel Network Bus – connecting the control panels to a computer with a managing program, connecting the panels into a network;

• System Bus – communications between the control panel and RAS, DGP expansions;

• Local Bus – communications of DGP and RAS with their peripheral equipment.

Due to its nature, the subject of Control Panel Network Bus has been divided into communication with a PC, and network operation of the control panels. Service connection with a PC has been described in the first part.

PC

Service

Diagnostics

PC

TITAN

System Management

Station

1

° Control Panel Network

Bus

SMA

SMA

SMA

Reporting

Control Panel

Control Panel

Control Panel

2

° System Bus

RAS

RAS

RAS

DGP

DGP

DGP

2

° Local Bus

Readers,

DGP,

Addressable sensors,

Wireless devices

Drawing 3-1 Advisor MASTER system communications diagram.

3.1 System bus

The ATS system design assumes communications between system elements (DGP,

RAS) with a master unit – the control panel (Drawing 3-2). Up to 16 RAS stations and 15

DGP devices can be connected to one control panel. The control panel itself is identified


as DGP number 16. The device number – its address – is set in each device attached to the bus by a DIP switch or through software. There are no limitations as to the sequence of addresses of the connected devices. The control panel queries each ATS system component connected to the system data bus. Lack of response to the polling signals sent triggers the tamper alarm with appropriate consequences. Therefore providing reliable communications between the control panel and peripheral equipment is very important to proper system function.

System Bus

ATS Control

Panel

(DGP 16)

RAS 1-16 DGP 1-15

Drawing 3-2 Basic construction of the Advisor MASTER system bus.

The system bus communications are implemented using the RS485 interface – a serial data port with balanced and symmetric connection – one of the most interference resistant systems used in electronics.

Table 3-1 Characteristic parameters of the system bus

Parameter Value

Interface RS485

Transmission mode Half Duplex

Bandwidth (bps)

Range (m)

Loop resistance (Ohm)

4800

1500

235

The provided bandwidth is adequate due to the system of distributed processing implemented. Each system expansion has it’s own processor, and all necessary data processing equipment for analyzing the system inputs. The RS485 interface range –

1500m – is guaranteed under optimal working conditions: with proper line fitting, and appropriate wiring.

Line fitting is done using resistors placed at the start and end of the transmission line.

This operation secures a typical value for system bus resistance is 235Ohm. All ATS system devices, except the ATS1190/92 Smart card readers, and hands free sensors expansion ATS1230, working with the system bus have inbuilt terminating resistors, activated via a jumper or DIP switch. Regardless of the circumstances the resistors can only be activated in the two most distant, opposite ends of the network.

3.1.1 Wiring

For proper data transmission only three wires are necessary, a twisted pair for D+ and D- signals, and power supply 0V for reference – Drawing 3-3. Nevertheless, to achieve the maximum data transfer range, care about the proper technical parameters of the wires must be taken.

Suggested cables: The suggested cables for the ATS system bus– RS485, 4800bps – are:

• Belden 8723

• Aritech WCAT52


• Aritech WCAT54

Use of the abovementioned cables guarantees failure-free operation, and the maximum declared bus range – 1500m. For data bus wiring, other cables can be used if meet following requirements: cat 5, twisted pair, STP or FTP.

Table 3-2 Technical parameters of the suggested cables.

Description

Cable type

Wire count

Pair count

Single wire resistance (Ohm/km)

Capacity between wires (nF/km)

Capacity between the wire and the shield (nF/km)

Maximum transmission range(m) 1500

Belden 8723 WCAT52 WCAT54

Cat 5.

Shielded

Twisted Pair

4

2

57,4

Cat 5.

Shielded

Twisted Pair

4

2

84

Cat 5.

Shielded

Twisted Pair

8

4

84

120 45 45

200 100 100

1500 1500

3.1.1.1 Shielding

The data cable shield needs to be connected to the system grounding. Every system ground needs to lead to a single point, and the shield cannot be grounded on both ends, due to the risk of current loops in the shield.

+12V

0

D+

D -

Drawing 3-3 Wire connections in the system bus

When using the ATS1470 isolators, the appropriate grounding rules need to be observed, and the shield needs to be connected properly. The shield has to be connected only to one cable, and only on the side of the system from which the isolator draws its power.

Although such a solution has significant limitations, it is possible to supply peripheral equipment with power using the data bus. The Drawing 3-3 shows such a connection..

The power supply output efficiency of the data bus is limited to 1A (F4 resistor in the control panel). Much more restrictive is the transmission cable load limit. The acceptable voltage for the system components is 10.5V DC. In case of the WCAT52/54 cable a load of 100mA would cause the voltage to drop from 12V to 10.5V after only 89m of cable. In case of the Belden 8723 cable such a drop would occur after 131m due to it’s lower resistance. Detailed calculations can be found in Table 3-3.

To increase the range, the number of power supply wires in the cable can be increased

(in pairs of +12V and 0V), but this solution is not advisable, and under no circumstances should it exceed a distance of 100m


36

5

9

Table 3-3 Data bus power supply – Maximum Range.

Current mA Belden WCAT52/54 WS108

50 261m 179m 167m

100 131m 89m 83m

150 87m 60m 56m

200 65m 45m 42m

250 52m 36m 33m

All the functional ATS devices – DGP and RAS – communicate with the control panel using the data bus. The data bus address space (RS485 – 32 devices) is divided into two groups, DGP and RAS, addressed separately. The system bus compatible RAS and DGP device list can be found in Table 1-10 and Table 1-22.

DGP addressing is carried out by setting the DIP switch on the PCB board of the device.

There can be maximum 15 DGP devices in the system, numbered 1 to 15. For the DGP device to be visible in the system, it’s pooling needs to be enabled. The ATS1250/60 devices accept addresses 1 to 12 due to the access control DGP count limit to 12 devices. The remaining addresses can be assigned to ATS1201/03/10/11/20 DGP units.

The control panel is identified as DGP number 16. The DIP switch settings for the DGP module addresses are presented in Table 3-4. DGP module addressing is vital for alarm zone addressing space usage.

Table 3-4 RAS and DGP addresses and numbers in the ATS system (DIP switch settings)

Device

Number

DGP Address

ATS1201/03

ATS1210/11

ATS1220

ATS1250

ATS1260

RAS Address

ATS11xx

1

13 1011 - 0011

14 0111 - 1011

15 1111 - 0111

16 Control 1111

The RAS station addressing is done either through software, or by an appropriate setting of the DIP switch on the device’s PCB board. The devices that can have their address set by programming are ATS1190 and ATS1192 – smart card readers. The default address value for their address is 16. There can be up to 16 RAS devices in the system, numbered 1 to 16. For the RAS devices to be visible in the system, they have to be activated by switching on the pooling of the appropriately numbered RAS device. By

ATS Designers Guide

default, after system memory restart, only the RAS number 1 is pooled. All RAS device activity is saved in the system according to their number. The RAS station number also defines the door number for central station based access control.

In accordance with the RS485 interface specification, the basic layout for the system bus is a cascade connection of 32 devices. 16 RAS devices and 15 DGP devices can be connected to the Advisor MASTER system data bus, which, along with the control panel, gives 32 sending/receiving devices connected to the RS485 interface.

The bus configuration limits are imposed by the signal propagation in complex networks.

The signal “echoes” – a consequence of the signal bouncing in long network branches due to different branches delay time – can cause multiple responses from one module, which would be interpreted by the control panel as system sabotage. According to its design, a system of class 3 and 4 should recognize and react to subsystem shutdown attempts by switching devices. The echo effect can be mitigated through the use of

ATS174x bus expansion modules. The maximum bus length limits come from timing dependencies of the device querying procedure. Any pooling errors or problems can be read from the system menu, or through the diagnostic module of the TITAN software.

Each device connected to the ATS control panel has an inbuilt communication error counter (max 255). That information can be used to test the bus configuration after system installation.

T

1

Because using only the cascade connection of system devices could be problematic, some modifications of the cascade connection, as well as developing more complex networks is permissible using the system bus accessories – the ATS174x devices.

2 3 . . . . 32

T

1500m

Drawing 3-4 Cascade connection

Standard data bus connections are the cascade connection and cascade connection with branches up to 1500m. The control panel can be located in an arbitrary location in the chain creating two branches. It has to be kept in mind that the total length of the bus cannot exceed 1500m.


T

1

9m

2

3

4 . . . . 32

T

5 31

T

1

1500m

Drawing 3-5 Chain connection with branches from the main bus course.

3.1.3.2 Increasing the system bus range

•

ATS1740 Repeaters - Isolators

The system bus can be increased using the insulator/amplifier ATS1740. Each repeater increases the bus range by 1500m. The total bus range is limited to 6km which means that the maximum number of cascade connected repeaters is 3.

Galvanic insulation1.5kV

2 . . . . 32

T

T

ATS1740

T

1500m 1500m

Drawing 3-6 Using the ATS1740 amplifier to increase the bus range.

•

ATS1743 Optical fibre interface.

Another method of increasing the bus range is by using optical fibres and the ATS1743 interface. The device uses the popular, and relatively cheap multi-mode 62,5/125um optical fibres, working in the lower infrared range – 820nm wavelength. It provides a cheap and tested solution to the bus range problem. The device can work in two modes:

− Point-To-Point – with a double optical fibre – this way 2 system branches, 1500m each, can be connected.

− Multi drop – with a single optical fibre– in this way the whole system bus can be designed using only optical fibres, or more branches can be connected in a star configuration (see chapter Star configuration) or branched bus.

The maximum distance between two ATS1743 interfaces is dependant on the parameters of the installed optical fibre and on the quality of the connections. A typical value of optical budget for the connection is 15dB.


T

1 2

Galvanic insulation . . . . 32

T

T

ATS1743 ATS1743

T

1500m

L

1500m

Drawing 3-7 Connecting two branches using two optical fibres via the ATS1743 interface.

A typical use of the fibre-optic modules, besides extending a single bus branch, is a branched bus configuration. The main bus is laid out using an optical channel, and the branches using the RS485 interface. This way, many branches can be designed that should total less than 6km in length and not exceed 1500m for a single branch. The fibreoptic bus length is dependant on the parameters of the fibre used.

1 2 . . . . 32

ATS1743 ATS1743

. . . . 32

ATS1743

ATS1743

. . . . 32

Drawing 3-8 Optical bus with RS485.branches

Basing the bus design on optical fibres creates a need for every device to have its own power supply. This can be troublesome in a system with control panel driven access control, because every RAS controlled door would need to have its own power supply with battery back-up.


1 . . . . 32

T

1

Galvanic insulation

Optic fibre

L

Drawing 3-9 Fibre-optic bus design using the ATS1743 interfaces

•

Dedicated leased line modem

A modem connection on a dedicated line can be used to extend the bus range. Maximum range of the connection is 3km – minimum cat. 2 phone cable, line without amplifiers,

MOD6000 modems. It is not permissible to use the internal phone network to connect the subsystems. Due to security concerns, the line must be dedicated to ensure permanent connection. Maximum length of connected bus branches is 1000m.

2 . . . .

T T

32

T

1000m 1000m

L

Drawing 3-10 Extending the bus, using modems and a dedicated leased line

More than two bus branches can be achieved using the ATS1470 repeater/insulator modules, or the fibre-optic modules. At the centre of the network is always the control panel.

•

ATS1740 Amplifier modules

When creating a star configuration network using the ATS1470 repeater/insulator modules up to 6 branches can be connected, with up to 1000m length each.

Table 3-5 Branch length L (m) depending on the number of branches.

Branch count Branch length

Number of

ATS1740

L (m)

1 1500

4 1500

6 1000

Expanding single branches using additional ATS1470 amplifier/insulator modules is possible if the total bus length would not exceed 6km. If the planned bus range is larger than this limit, the use of ATS1743 fibre-optic modules should be taken into consideration.


T

1

Galvanic insulation

1.5kV

. . . .

ATS1740

T

L

. . . .

ATS1740

T

L

5

T

15

T

. . . . 3

T

T

ATS1740

T

L

Drawing 3-11 Star configuration using ATS1740 insulators.

In case of replacing an older system with Advisor MASTER, the existing bus wiring can be adapted. In that case, using ATS1470 amplifier/insulator modules, up to 6 branches of non-twisted, non-shielded 300m cable can be connected.

•

ATS1743 fibre-optic modules

Using optical fibres for communications gives many possibilities for system expansion.

Creating a star configuration using fibre-optic modules is justified if the star configuration is both extensive and remote, or if the available bus branch range is not sufficient. In that case, the modules can be used to expand the range of single branches.


1

42

2

ATS1743

. . . . 5

ATS1743

ATS1743

. . . . 15

ATS1743

. . . . 12

Drawing 3-12 Star configuration using ATS1743 modules.

•

RS485 Loop

In the case of a risk of system bus severance, an ATS1742 loop interface can be used.

The device provides bus cut signalling, and sustains communications with both bus branches after bus cut. The loop interface also has an amplifier, so the length of the loop is not dependant on the connection topology. Unfortunately extending the loop using the methods described in paragraph Increasing the system bus range is impossible.

Therefore the maximum loop length is 1500m. Nevertheless all limitations mentioned there are valid.

5

1

T

T

.

T

T

31

32

L = 1500m L = 1500m

Drawing 3-13 System bus loop configuration.

ATS Designers Guide

T

1

•

Remote star

In case the need arises to design a remote star configuration too extensive to allow the use of the ATS1740 amplifier modules (the total of the branch length is more than 6km), the fibre-optic modules can be used – Drawing 3-14.

Galvanic insulation

Galvanic insulation

1.5kV

. . . . 5

T

ATS1740

T

L

1000m

. . . . 15

T

* -Additional power supply necessary

ATS1740

T

1000m

. . . . 3

T

T

ATS1740

T

1000m

Drawing 3-14 Remote star configuration.

3.2 Local bus

3.2.1 ATS1250/60 access control DGP

3.2.1.1 RS485

The ATS1250/60 access control DGP local bus has the same parameters as the system bus and is therefore subjected to the same design rules. All system bus specifications – the wiring, device addressing, topology etc. – hold their power when designing the access control DGP local bus.

Using the local bus, up to 16 readers and 15 DGP modules can be connected to the access control DGP. DGP expansions are used in the ATS1260 elevator controller only.

The ATS1250/60 controllers are equipped with 4 interfaces for direct connections with

Wiegand and Clock&Data readers. The interface automatically recognizes type of connected reader.

The maximum distance from the reader to the controller is 70m – the wiring should be done using UTP/FTP cat. 5 cables. Connection D0 and D1 within single pair of wires should be avoided. It is recommended to pair the D0 and D1 signals with the ground. The


reader inputs have been doubled as local bus devices – readers (local bus RAS) with addresses from 1 to 4.

3.2.2 ATS1290 addressable sensor DGP

The ATS1290 addressable sensor DGP uses the PointID ® interface for communications.

It is a serial, bi-directional, open–topology interface. Its range is limited only by the load of the devices connected to the bus. The bus can have either two or four wires, depending on the power supply assumptions for the devices.

A supplement for the DGP is a set of sensors and other addressable devices, listed in

Table 3-10. These are popular PIR sensors, also equipped with anti-masking capabilities, and a set of universal devices for use with standard alarm equipment.

Using the addressable device technology enables:

• Shortening of the installation time;

• Decreasing the cost and complexity of the wiring;

• Simplifying extensions for existing systems and projects.

Connecting advanced sensors, equipped with anti-masking, Walk-Test capabilities, or the control of LEDs, often requires cables with 6 or more wires. Besides, each sensor needs to be connected via a separate, cable, and should be properly installed. Often the wiring loom consists of tens of cables many wires each. Adding new elements often requires laying out a cable from the nearest expansion to the detector. The addressable device system is free from such limitations. Only one cable is necessary, laid out from sensor to sensor, DGP to connection box etc. in an arbitrary fashion. The cable can also be the same one that provides the system bus signal, and adding a new sensor consists of only connecting it to the nearest existing device.

Table 3-6 Point ID interface parameters

Parameter Value

Device communications

DGP communications

Addressing

Packet transmission time

Voltage based PPM

Synchronous CPM

Device: DIP, DGP: learning

Device 8ms, DGP 4ms

Number of wires

Number of devices

2/4

32 (256 addresses max.)

Max. Length 1500m

Termination No

3.2.2.1 Wiring.

There are two ways to design a Point ID

® connected to it:

bus, depending on the power supply of devices

• Power supplied directly form bus – two wire bus;

• Power supplied form an external source – 4-wire bus.

Although there are no limitations as to the type of wires used for the bus, it is necessary to use wires with the lowest possible resistance and capacity to achieve the maximum bus length – 1500m. Drawing 3-15 shows several possible bus topologies used during testing.


Q

Y

X X

Z D G P

P

R

D G P D G P

P a n e l

D is trib u te d

Drawing 3-15 Typical Point ID

® configurations.

The cables in Table 3-7 have been listed by preference. When using shielded cables, the shield should be left unconnected, as this causes an increase of bus wiring capacity.

Table 3-7 Tested cable types.

Product Description Diameter mm

2

WCAT54

WN108

FTP cat.5, 4 twisted pairs

Unshielded, 8 non-twisted wires

0,22

0,22

WS108 Shielded, 8 non-twisted wires 0,22

The two tables– Table 3-8 and Table 3-9 – contain the test result for different numbers of connected devices under different power demand conditions of the two and four wire system bus. The load is given in UL (1 Unit Load = 300 uA) – a typical load of one transmitter/receiver device of the Point ID ® bus. All the available wires in the cable have been used for connections. The presented data clearly shows that the bus range depends mostly on the load of the connected devices.

The minimum bus voltage is 9,5VDC.

Table 3-8 Characteristic lengths of w 2-wire Point ID

®

bus.

Devices

Q-ty

Load Cascade, Remote star. X (m) Star Q (m)

UL WN108 WS108 WCAT54 WN108 WS108 WCAT54

32 1 1600 1200 1600 200 160 200

16 16 200 200 200 150 120 150

16 32 100 100 100 100 75 100

When using cables with less wire cores (less wire gauge), the range should be appropriately reduced. Example: WN104 – 4 wires, 0.22mm

be avoided.

2

– the range is reduced by

50%. In case of twisted pair cables, the pair separation between PID+ and PID- should

Table 3-9 Characteristic lengths of w 4-wire Point ID

®

bus.

Devices

Q-ty

Load Cascade, Remote star. X (m) Star Q (m)

UL WN108 WS108 WCAT54 WN108 WS108 WCAT54

32 1 400 300 400 50 40 50


The Point ID ® interface address space contains 256 entries from 0 to 255. This allows addressing of a different number of devices depending on the number of supported inputs and outputs. The Point ID

®

interface assumes sequent addressing of the inputs and outputs and providing direct access to them in the alarm system. Each device connected to the bus has an address definable by DIP switch settings – it is the address of the first input of the Point ID

® device – the following inputs and outputs are automatically assigned the proper addresses. The device maps the PID bus inputs to the system zones appropriate for the DGP address.

Table 3-10 Point ID

®

device load.

Product

SI-AD

Description

Universal, single input module

Inputs

1

Outputs

0

PID Load

1UL(330uA)

AD044 Universal 4I/4O module, external power supply

AD111

AP750-AD

IO module, installed inside the sensor

PIR sensor, range: 7 screens, 15.2m;

EV435-AD PIR sensor, 9/16m, 9 screens

EV435AM-AD PIR sensor, 9/15m, 7 screens, antimasking

1

1

1

1

1

1

1UL(330uA)

1-10UL(250u-3mA)

16UL(4.8mA)

46

The ATS1230 wireless sensors DGP is a receiver for RF series devices – listed in Table

3-12. The characteristic parameters of the communications protocol are listed in Table

3-11.

Table 3-11 ATS1230 transmission parameters.

Parameter Value

Frequency 433Mhz

Transmission Data batch, asynchronous, ITI

Transmitter testing

Packet count

Packet transmission time

Time between packets

Transmitter code bits

Information per packet

Random , max. 64 minutes

3, Alarm/Tamper 8

20ms

Random 125 - 487ms

20 bits

66 bits

Communications are unidirectional, the sensor sending packets 58-66 bits long, containing the identification data, and information about its state, at random time intervals no longer than 64 minutes. Each time 3 packets (8 in case of activation or sabotage) are sent at random intervals from 120ms to 450ms. It prevents an accidental signal overlapping from several transmitters. The receiver device also detects the lack of an antenna and radio signal.

Each transmitter has a unique, factory assigned, 20 bit code. The unique code used to identify the device is stored during the programming of the device. Because of that, it is impossible to substitute the device or to wrongly identify the device by the DGP. Apart from the code, the transmitter sends information about the state of the sensor (normal

/alarm /tamper), and the battery condition. The RF devices use standard, commonly available lithium batteries. The average battery life is 4-5 years.

ATS Designers Guide

Table 3-12 List of ATS1230 DGP compatible transmitters.

Product

RF320I4

RF352I4

RF354I4

RF356I4

RF360I4

Description

Wireless magnetic sensor (or a transmitter for a wired sensor – type NO/NC), sabotage



Wireless panic button in form of a wristwatch.

RF425I4

RF425I4PI Wireless PIR sensor, EV425, 9/16m, 9 screens, opening and tear-out sabotage alarm, PI version

RF572NSTI4 Wireless optical-thermal smoke detector, sabotage alarm, internal siren

RF620I4 Wireless inertia and magnetic sensor, sabotage alarm, white

RF620I4B

Water resistant wireless panic button, belt clip or neck leash.

Wireless PIR sensor, EV425, 9/16m, 9 screens, opening and tear-out sabotage alarm

RF903I4

RF900I4

Wireless inertia and magnetic sensor, sabotage alarm, brown

Wireless glassbreak detector, acoustic, plaster mounted, sabotage alarm

Diagnostic wireless sensor testing kit, 433MHz.

Range m

300

150

150

150

300

300

300

300

300

300

300

300

The device programming is very simple and consists of ”learning” the DGP all the transmitters that it shall work with. The learning process consists of putting the DGP in transmitter storing mode, and activating the devices in order, in which they should appear in the system as alarm zones.

3.2.4 ATS1105 and ATS1170 RAS station reader interface

Both the RAS devices – ATS1105 and ATS1170 – have their own interface, for connecting a Wiegand/Clock&Data standard compliant reader. The ATS1170 has the reader type selectable by a DIP switch, and also can control the reader’s LEDs and buzzer. Additionally it can locally store data for 20 cards in case of a loss of contact with the superior unit.

The maximum distance form the reader to the controller is 70m – the wiring should be done using UTP/FTP cat. 5 cables. Connection D0 and D1 within single pair of wires should be avoided. It is recommended to pair the D0 and D1 signals with the ground.

3.3 PC connection.

A modern system, regardless of its complexity should offer an ability to connect to a PC.

The connection should enable communications with computer programs that provide automated system maintenance, system programming, managing and monitoring etc.

This chapter summarises the basic information regarding the configuration of a PC connection for communications with appropriate utilities.

Each ATS control panel has a RS232 service connector (J18), which enables a direct connection to a PC with the TITAN

® software installed. This approach enables system programming and maintenance without additional costs (required equipment in

Table 3-14), which is especially important in small systems, that do not require advanced system monitoring functions. The connection has some limits:


• Have to be initiated from the system keyboard;

• Must be confirmed by the Master User Code;

• The connection is limited to 40min – after that the connection is automatically discontinued.

Those limits, while protecting the system from unauthorized user access, define the use of the connection only for control panel programming and maintenance purposes.

Table 3-13 J18 transmission parameters.

Parameter Value

Interface RS232

Cable length 10m

Bandwidth 4800bps

Connection duration 40min.

Initiation Keyboard/Master User

Pooling Yes

Table 3-14 List of equipment necessary for J18 maintenance connection.

Required equipment

ATS1630

Description

RS232 port programming cable (from the J18 service port)

This approach enables system programming and maintenance without additional costs

(the necessary equipment consists of a RS232 cable), which is especially important in small systems that do not require constant system monitoring functions.

3.3.2 PC direct connection

A permanent connection between the control panel and a computer with a managing program is established in a different way. Besides the ATS2000, all control panels are equipped with a connector (J11) for installing the ATS1801 computer interface. Using the

ATS1801 interface, allows time – unlimited connection to a PC and system monitoring software. The connection is initiated by the managing software. The connection parameters are set via the control panel, and are the only parameters not available for modification by the managing software. They define the connection properties with regard to allowed operations depending on the system state – programming, system control in armed and disarmed state. In this mode, all the functions of the TITAN software are available.

Table 3-15 ATS1801 direct connection parameters.

Parameter Value

Interface RS232

Bandwidth 4800bps

Connection duration Not limited

Initiation Titan software

Querying Yes

Table 3-16 List of equipment for ATS1801 direct connection.


ATS1801

Description

ATS1632

Computer, printer interface (two RS232 ports) for the control panel

PC-RS232 connection cable for the ATS1801 interface (5m)


The ATS1801 interface has two RS232 ports that enable communications with a computer and printer or a digital video recorder. The connection isn’t time-limited and the connection security is ensured by a 10-digit security code that must be the same in the control panel, and the PC to activate the connection.

3.3.3 Increasing the range between the control panel and PC.

Often the control panel is located a considerable distance from the PC on which the system management program is running. Therefore the issue is vital for system design, and it is necessary to predict what elements are required to connect the control panel to the monitoring computer.

3.3.3.1 RS485

To increase the connection distance between the Advisor MASTER control panel, and the PC with the managing software the system bus accessories can be used. By converting the RS232 into RS485, we can achieve a maximum distance of 1500m. Bigger distances can be achieved by following the steps described above in section 3.1.3 paragraph Increasing the system bus range

Table 3-17 Equipment list for remote RS485 connection.


ATS1801

ATS1741

Description


RS485 / RS232 bus converter

3.3.3.2 Modem and a dedicated leased line

Amt.

1

2

Another solution is to use a leased phone line. Modems need to be installed on the control panel and computer side of the line.

Table 3-18 Equipment necessary for remote modem connection


ATS1801

Description

MOD6000


External modem for communication with

ARITECH systems.

3.3.3.3 TCP/IP

Amt.

1

2

By using RS232 – TCP/IP converters, the Ethernet network can be used to communicate with the control panel. Although the bandwidth used by the Advisor MASTER system is small the security system communications need to be made using separate wiring. This is dictated by the need to protect the system from access by unauthorised persons.

Table 3-19 Equipment necessary for TCP/IP connection.


ATS1801

ACA300

Description


TCP/IP to RS232 converter

Amt.

1

1


A serial port emulator is supplied together with the ACA300. Using the program enables the use of a network card for communications with the TITAN

® software, which only uses serial ports for communications.

3.3.4 Modem connection

The control panel communicators are equipped with a modem, which can be used for service communications, and for system programming. Using the inbuilt communication methods is limited by the small bandwidth, which excludes them from being used for system monitoring. Apart from that, it is the main reporting route to the CS station. As a result, blocking it for longer periods of time is not good practice.

The ATS system can be equipped with additional communications equipment that provides additional reporting channels. By design all communication routes for event reporting are equal. The same holds true for data transmissions.

Table 3-20 Equipment and connection parameters for a modem connection.

Communication channels

Expansion Bandwidth

All channels support connections in two modes:

• Multi-ring – the control panel responds to a connection attempt after a given number of rings and tries;

• Call-back – the control panel calls back a pre-programmed number after a given number of rings and tries;

Both modes are available on demand, or according to a pre-programmed connection schedule.

3.4 Control Panel Network

In cases when, due to any circumstances, one control panel is not enough to fill the requirements of the system, a network of control panels can be created by connecting them to a common computer system, equipped with system management and monitoring software. One computer system can support 64 control panels at the same time. Using time-limited connections, the TITAN software can support up to 1024 control panels, but at the same time only 64 control panels can be communicated with.

The basic control panel network configuration is the direct connection using the RS485 interface with the same communication parameters as the system bus. Using the available system bus accessories, a system bus branch is connected to the computer’s serial port. Up to 16 control panels can be connected to the branch.

Table 3-21 Advisor MASTER control panel parameters.

Parameter

Number of connections (ports)

Number of control panels with active connection.

Number of control panels connected to one port (max.)

Number of control panels in one TITAN system

Value

16

64

16

1024


3.4.1 Control panel bus topology and wiring

The basic control panel bus implementation is the RS485 interface. The design guidelines for the control panel bus are the same as the wiring– see 3.1.1 – and topology guidelines – see section 3.1.3 – for the system bus. Drawing3-17 shows a basic control panel network using the system bus interface and accessories.

To implement a single bus branch, the following components are necessary:

• Control panels with the ATS1801 interface;

• ATS1741 RS232-RS485 converters;

The table below (Table 3-22) shows how to select equipment necessary to connect the control panels this way.

Table 3-22 Equipment necessary to connect a network of N<16 control panels.

Product Description Amt.

ATS1801 Computer, printer interface (two RS232 ports) N

ATS1741 RS485 / RS232 bus converter N+1

PC

TITAN

RS232

ATS1741

T

RS485

RS232

ATS

Control Panel

+

ATS1801

RS232

ATS

Control Panel

+

ATS1801

T

Drawing 3-16 Basic control panel networking bus design.

The flexibility of querying the control panel by the TITAN software (the poling time, and timeout is set by software) allows the design of more complex networks than those based only on the RS485 interface. For more complex implementations, the connections described in sections 3.3.2 and 3.3.3 can be used. The paragraphs contain information about direct connections between the computer and the control panel, as well as increasing the distance between them. The following paragraph shows an example of a control panel network using the Ethernet network and other connection methods.

3.4.2 Examples of CP networks connected by various communications interfaces.

All control panels in the system are queried according to a programmed schedule, which means a lack of response from any of the control panels will be stored in the system event log. Depending on the system functions, and the security level expected from the system, the control panel network can be implemented in various ways. The provided example shows only one of the methods.

The network design assumes:


• The monitoring station has a direct connection to the control panels in the given location.

• One of the control panels is located in a separate building, connected only by

Ethernet wiring.

• Beyond the premises (eg: another city) are two additional control panels, which should be queried once a day, at a given time to synchronise the event log. One of them doesn’t have access to a phone line.

The provided solution assumes communications between the PC monitoring station and the local control panel using TCP/IP local network, and further along using the RS485 interface and bus accessories. The remote control panel can be accessed using the

Ethernet network, or connected directly. The control panels outside the premises can be contacted by modem using a phone connection (for the control panel with phone line access) and GSM connection (the control panel is equipped with the ATS7300 GSM communicator for connecting to the monitoring station and the CS reporting station).

The provided solution requires the use of 3 branches/ports of the TITAN software. Note that the maximum number of connections is 16 (older TITAN versions – 4 only).

If the remote location would require a service connection – programming, diagnostics without event archival and system control – the modem can be left out and the inbuilt communicator can be used. This solution is not advisable, as it doesn’t allow reporting events to the CS station during the connection to a system monitoring station.

PC

TITAN

MOD6000

Ethernet*

ACA300

ATS1741

T

RS485

ATS

Control Panel

+

ATS1801

ACA300

RS232

ATS

Control Panel

+

ATS1801

MOD6000

RS232

PSTN

Leased line

GSM network

ATS

Control Panel

+

ATS1801

ATS

Control Panel

+

ATS7300

ATS

Control Panel

+

ATS1801

* -The TITAN software does not support the TCP/IP protocol. It’s necessary to install a serial port emulator on the PC

T

Drawing3-17 Control panel network implementation diagram.

3.5 Reporting events to the CS station

Quick and effective reporting of events to several CS stations, using several communication channels is essential for systems with higher levels of security. The ATS system event reporting concept assumes availability of the same functions regardless of the control panel type. Up to 4 independent CS stations can be programmed in the

Advisor MASTER system, each having 2 alternative phone numbers. The reporting can work in two modes:


• Serial – The system sends the message until the first successful transmission to any of the programmed CS stations;

• Parallel – The system sends reports to each programmed CS stations until all confirm receiving the message.

Table 3-23 CS station communication channels and the necessary expansions

Communication channels Expansion

PSTN None

ISDN ATS7100

GSM ATS7300

Every CS station can be programmed for reporting on different communication channel – the available channels are analogue (PSTN), digital (ISDN) and cellular (GSM) phone lines. Each channel supports every event transmission protocol implemented. Due to a timing conflict between the transmission protocol and the GSM network delay, the

ATS7300 communicator has been equipped with an algorithm to disqualify the influence of the network delay on the CS station communications.

Table 3-24 ATS control panel reporting system parameters.

Parameter

Number of CS stations

Phone number count

Communication channels

Number of protocols

Value

4

2 each CS (8 in total )

Analogue PSTN/ISDN/GSM

17

Besides the abovementioned communication characteristics, the system can freely shape the event reporting method. That option is available through the event class database, a programming option available in each control panel.

Table 3-25 Reporting protocols.

Protocol

Tecom V1 phone communicator

Contact ID – Small

Contact ID – Large

SIA – Small

SIA – Large

XSIA – Small

XSIA – Large

200 Baud FSK Format 1




4x25 Enai

Voice reporting with confirmation

Voice reporting without confirmation

Secure Stream

Securitel serial number

Securitel PIN code

Remarks

Used in Australia only

Requires the ATS7200 module


54

4 C

ONFIGURATION OF THE

A

DVISOR

MASTER

I

NTEGRATED

S

YSTEM

The design of an integrated system is limited to a configuration for a single control panel

– the systems controlled by a single control panel. Designing larger systems – networked systems – consists of steps described in chapter 5 and multiple repeats of the procedure described here.

The core integrated system design issue is the translation of design requirements to the system implementation – the control panel type, and the type and number of necessary expansions. At it’s most general, the design requirements for the Advisor MASTER system are shown in Table 4-1. Based on those parameters the control panel type, as well as the number of expansions in the system can be tentatively defined – see Table

4-2. The design limits lie mainly in the selection and configuration of the DGP expansions, which not always use all the available alarm zones – see section 4.2.

Defining the control panel type and the placement of DGP expansions is also dependant on the functional requirements for the system.

Table 4-1 Design parameters of the ATS integrated system.

Parameter

Number of alarm zones

Number of areas

Number of users

Number of manipulators

Unidirectional passages

Bi-directional passages

Elevator control

Number and type of readers

Special functions:

System Monitoring

Event reporting

Integrated access control

CCTV integration

Description

Defines the type and the number of control panels in the system, also the type and number of expansions. The access control passage zones need to be included if they are to be monitored.

Defines the type and number of control panels, also the number of manipulators and other devices in the system.

For access control, defines the necessary system memory expansions and number of cards.

The number of areas and access control functions define the type and number of manipulators present in the system

Doors with a reader on one side, and an exit button on the other; define the number of readers and other access control expansions, as well as the use of access control functions of the control panels.

Doors with readers on both sides – antipassback function, card and

PIN etc. Define the number of ATS1250 DGP, the number of readers an other access control accessories.

Defines the number of DGP expansions and the number of readers in the system;

The number of readers, keyboards – dependant on the number and type of passages ; The type of readers – defines the number and type of expansions (memory, DGP etc.) and the card type.

Unlimited (HDD) common event log, system control, monitoring the system state, graphical user interface – maps.

Defines the channels and methods of communication with the CS stations.

The use of access control functions in the system influences the use of the expansion address range, but also the availability of additional functions : user counting – automatic system arming and disarming, changing access rights depending on user presence etc.

Registering events along with a video signal, controlling the video recorder from the ATS system keypad, controlling the CCTV system from the ATS system

ATS Designers Guide

The access control functions in the Advisor MASTER system are integrated with other system components. It allows the same devices that control the alarm system to verify user access rights. The same applies to alarm zones – the sensors used to check door opening can be used to secure the area in the alarm section. In this regard, the system is unified and consistent but needs to be carefully designed.

4.1 Control panel selection and configuration

The control panel selection should be based on the system design requirements – both the functional and quantitative. The most important parameters influencing the functionality of a system based on a given type of control panel are gathered in Table 4-2.

Only a small number of parameters differentiates the use of a control panel in a system of a required functionality.

Table 4-2 Control panel parameters.

Parameter ATS2000 ATS3000

Alarm zones 32(8) 64(8)

ATS4000

ATS4500

256(16)

Users 50 50-11k (67k) 50-67k / 11k-67k

Manipulators 16 16 16

DGP Expansions (AC) 15 (12)

Unidirectional passages* 16

15 (12)

16

15 (12)

16

Bi-directional passages 48 48 48

Elevators/Floors 4/64 4/64 4/64

Alarm event log

AC event log

250

10

250-1000

10 – 1000

250-1000

10-1000

Special functions

System monitoring

Event printer

Access control

CCTV integration

No

No

Yes*

No

Yes**

Yes**

Yes**

Yes**

Yes

Yes

Yes

Yes

Network capabilities No

Service connection Yes

Yes**

Yes

Yes

Yes

*- the limits of the ATS2000 results from hardware limitations – see section 1.1.

**- the limits of the ATS3000 for access control systems results from the hardware limit of the possible configurations of memory and other expansions. – see section 1.1 – it is not possible to install the IUM ATS1831/32 memory expansion and the ATS1801 computer/ printer interface together.

Only two parameters are directly dependant on the control panel type – the maximum number of alarm zones, and system areas. Other parameters depend on the capability to install other expansions:

• The control panel memory expansion – influences the size of the event log, the number of users, and indirectly the format of access control cards.

• The computer/printer interface – influences the availability of a fast, permanent connection between the control panel and the computer or a control panel network.

Lack of such an expansion excludes the control panel networking capability, monitoring, connecting the event printer etc.

• The number of zones and outputs in the control panel;

• Available reporting channels.

The control panel parameters and design requirements should be analysed in the following order:


• The characteristic values of the alarm system – alarm zones, areas – those parameters describe the capacity of a system based on a selected control panel.

Although they depend on the DGP expansion configuration (number of alarm zones), the control panel type unequivocally defines their maximum number in the system.

• Computer or control panel network connection – system monitoring, event printer, network operation – define the need to install the ATS1801/02 computer/printer interface.

• Users and access control range – selection of a memory expansion influencing the number of users, access control card types and their range, the size of the event log etc.

• Alarm zones and system outputs expansions – the type and size of the installed expansions influences the size of the control panel housing.

• Reporting communications (CS) – appropriate communications modules need to be installed in the system.

4.1.1 The procedure of selecting and configuring the alarm system control panel

4.1.1.1 Step I. Characteristic parameters – zones, areas

32 zones

4 areas

256 zones

16 areas

Alarm Zones

Areas

64 zones

8 areas

ATS2018 ATS3018 ATS4018

ATS4518

Drawing 4-1 System Capacity

The characteristic parameters of the control panels, independent of the installed expansions define the maximum system size, that is the number of alarm zones and areas of the alarm system. Alarm zones, areas – maximum system capacity, regardless of installed expansions.


4.1.1.2 Step II. Connecting the system to a PC

NO

YES

Connection with a

PC, printer or CCTV system

ATS2018

ATS3018

ATS4018

ATS4518

ATS3018*

ATS4018

ATS4518

+ATS1801/02

*- only ATS1830 memory- 1Mb

Drawing 4-2 Connecting the control panels to a computer, printer or CCTV system.

If any of the abovementioned functions is required, the control panel needs to be equipped with the ATS1801 module – the computer/printer interface; or ATS1802 – printer interface; This excludes the ATS2000 control panel – it doesn’t provide a connector for the abovementioned modules, and limits the choice of memory expansions for the ATS3000 control panel.

Monitoring and managing the system from the computer station, either remote or local;

• Event printer;

• Digital recorder integration;

• Control panel network connection;

4.1.1.3 Step III. Users and access control range

Each memory expansion extends the system functionality through:

• Increasing the number of alarm groups from 70 to 138

• Increasing the number of door groups from 10 to 128

• Increasing the alarm log size from 250 to 1000 entries.

• Increasing the access control log from 10 to 1000 entries.

Besides that, the use of memory expansion modules increases the number of users in the system, and provides additional functions:

• IUM – storing the whole (up to 48 bits) data stream of the card;

• Quick searching of the database–the ATS1831/32 expansions.

The IUM functions frees the system from limits imposed by the access card formats.

Drawing 4-3 shows a diagram of the access card range, and the number of users in the system depending on the memory expansion. Detailed information about access cards can be found in section 4.4.

The Table 4-3 below contains the available memory expansions and user configurations.

Because the access control DGP stores a local copy of the user database, the same memory expansion needs to be provided for both the DGP and the control panel. Not all memory and expansion configurations are available for every control panel. This is shown


on Drawing 4-3. However every configuration shown below is available for the

ATS1250/60 access control DGP. The manual’s appendices contain a table with all memory and control panel configurations.

Table 4-3 Memory configurations

Configuration Expansion Users Card format

Name PIN Card

Standard None

TIUM

MIUM

None 50

ATS1830 – 1Mb 200

LM

SIUM

ATS1830 – 1Mb 200

ATS1831 – 4Mb 200

50

2000

1000*

17000

50

2000

11000

17000

All up to 48-bits, IUM


Table 4-19


LIUM ATS1832 – 8Mb 200 67000 67000 All up to 48-bits, IUM

*- for users above 1000 the PIN codes are generated automatically, and cannot be changed.

Available passages:

16 control panel

48 AC DGP

Memory

ATS Smart cards

Wiegand 26-bit**

Access Control card format

DGP formats

ATS1250/60

Tablae4-19

Available passages:

48 AC DGP

Memory

Other up to 48-bits

IUM

Available passages:

16 control panel

48 AC DGP

Memory

58

Brak ATS1830 ATS1831

ATS1832


ATS1832


ATS1832

50

ATS2018

ATS3018

ATS4018

11k

ATS3018

ATS4018

ATS4518

17k 67k

ATS3018*

ATS4018

ATS4518

50

ATS2018

ATS3018

ATS4018

11k

ATS3018

ATS4018

ATS4518

17k 67k

ATS3018*

ATS4018

ATS4518

50

ATS2018

ATS3018

ATS4018

*- Unavailable if ATS1801/02 was selected in the previous step

**-card format offering a small number of card and system codes. Not recomended.

Drawing 4-3 Access card range, and memory expansion application.

2k

ATS3018

ATS4018

ATS4518

17k 67k

ATS3018*

ATS4018

ATS4518

•

Additional system functions.

User verification functions are available in the system through the TITAN software, equipped with the Photo ID module, which allows storing of user photographs in the database. The photos can be supplied as a file, or made using a digital camera and added to the database on the fly. The photographs can be shown on screen whenever the user passes a door.

The TITAN software is equipped with access card personalisation functions. It provides a card design editor, which uses the information from the user database along with the

ATS Designers Guide

Photo ID database to cost effective and simple design and print custom, personalised access cards. The TITAN software works with every Windows compatible card printer.

4.1.1.4 Step IV. Expanding alarm zones and system outputs.

The control panels allow extending the number of available alarm zones using DGP modules (described in section 4.2) and by using the ATS1202 control panel expansion.

Connecting the ATS1202 modules in cascade up to 32 alarm zones can be achieved.

Each ATS1202 module occupies one B – type slot in the housing.

If the design requires control panel outputs, relay output or OC output, expansions can be installed. Besides the power supply and free housing space, there are no limits as to the outputs supported by the control panel. The available expansion combinations can be found in 1.1.

The ATS4500 control panel is functionally identical with ATS4000. This model comes with the ATS1830 memory expansion preinstalled. The device is delivered with the ATS1644 housing, which provides ample space for additional expansions. The same memory expansion and housing are provided with the ATS1250/60 access control DGP. That’s why it is a recommended combination for systems with higher security standards and integrated access control.

4.1.1.5 Step V. Central Station Reporting communications

Depending on the requirements for the system based on the CS station reporting, the appropriate communicator module needs to be selected. As all communication modules use a dedicated MI bus, and can be mounted under the control panel mainboard, this configuration step is independent of the rest.

4.2 Configuring the DGP expansion modules.

Further alarm system design is described for the ATS4000 control panel. This is the basic control panel type, from which the other types differ only by the size of the system, and the availability of certain expansions. Details can be found in section 1.1.

4.2.1.1 Inputs

The address space of the alarm zones is divided between the control panel and the 15 remaining DGP modules. The division is predefined and does not depend on the installed control panel or other equipment. Thus, the alarm zone numbers are permanently fixed to the DGP expansions of a given address. Only the total number of zones is limited in a control panel, not the addresses. This simplifies the system design in terms of the area covered and the possibility of using any expansion types.

It has to be noted that the control panels and DGP modules are expandable up to 32 zones, and the address space division assumes 16 zone numbers per DGP. If the control panel or the DGP is expanded beyond 16 zones, the next zones occupy addresses from the next DGP address range. While there are no technical limitations for address doubling, it is not recommended because of good practice of security system design.

The opposite is a situation in which devices with less than 16 addresses are used. For example the ATS1220 provides only 4 alarm zones and cannot be expanded, meaning, the whole 16 zone range being reserved, 12 alarm zone addresses stay unused.


Table 4-4 Available DGP modules and their expansions.

Expansion

MBC

Zones

ATS1202 ATS1810

Outputs

ATS1811 ATS1820

Remarks

ATS1210/11 8 2x4 2x8 1x16

ATS1220 4

ATS1290 32 device without a power supply.

Planning for maximum DGP expansion the maximum system capacity – 256 zones- can be achieved using 7 DGP modules. In an opposite case – using the mentioned 4 zone

DGP – after installing all possible DGP modules – 15 – all the expansions would make total of 60 alarm zones.

4.2.1.2 Outputs

A similar rule is valid for the division of the system output address space. The output addresses for a given DGP are defined by it’s address – number – in the system. DGP can support a maximum of 16 outputs, which is the same as it’s assigned zone address space. The control panel can support all the outputs, but due to power supply limits the number is capped at 150. A higher number of outputs can be made available by installing an additional power source.

Each system output is limited by a timezone. The system supports 16 areas, and for each one a separate external and internal siren. The ATS1201 DGP is equipped with dedicated, monitored siren output, addressed like the rest of the system outputs.

Table 4-5 Alarm zone and output addressing in the ATS system.

Input Range Output Range DGP Address

1-16 1-16 16 (CP)

Remarks

Control panel alarm zones

113-128 113-128 7

129-144 129-144 8

145-160 145-160 9

60

241-256 241-255

4.2.1.3 Sirens

15 Output 256 is not available

Each of the 16 areas can have two signallers defined: internal and external. Configuring the sirens in the system is the same as configuring the outputs: the event flag is assigned to an output. Apart from the control panel, the siren outputs are available in the ATS1201,

ATS1203 and ATS1250/60 DGP. The signaller outputs are protected by fuses and monitored. By default the system is programmed to activate all external sirens in case of an alarm in any area.

ATS Designers Guide

Table 4-6 DGP siren address map.

DGP Output Description

16 2, 15, 16 Control panel : Lamp, internal, external

Siren.

1 32 External

2 48 External siren

3 64 External siren

4 80 External siren

5 96 External siren

6 112 External siren









15 - Output 256 is not available

4.3 Areas

The control panels, depending on their type, have 4, 8 or 16 independent areas. Each area can have independently set entry and exit times, internal and external sirens as well as the beacon, reporting method etc. Common areas can be created in two ways: connecting the areas or assigning zones from the common location to all areas. The area linking mechanism is also used to create a cascade of vault areas. The areas linked with the vault areas will be armed automatically once the vault areas are armed.

In systems where the number of independent areas exceeds 16, a network of control panels needs to be used.

In cases when a large number of one-zone areas is necessary, for example, a shopping mall with one zone for each shop, armed separately, the zone type 33 can be used – 24h alarm and inhibit – which allows suspending of the zone using a keyswitch. This application requires a different method of zone wiring. This way, it’s possible to achieve up to 256 such security spots on one ATS4000 control panel.

4.4 Access control

The access control functions are available in the control panel. The RAS stations in the control panel can control doors. Though access control implemented this way has some limitations of the functions provided, it’s an affordable solution. It provides the basic system functions for 16 doors at an attractive price. If the system requirements are bigger, however, the ATS system can be equipped with a dedicated access control DGP, implementing the advanced functions of such a system while at the same time staying an integral part of the system. Four door – ATS1250 – and four lift – ATS1260 – modules are available. They act as a DGP, and to a single control panel, up to 12 access control DGP can be connected, which gives additional 48 doors per control panel. A detailed description of configuring the access control functions of the control panel and the

ATS1250/60 DGP is provided in the following paragraphs.

The door, or elevator numbers are permanently assigned to the DGP addresses, a detailed list can be found below.


Table 4-7 Passage and elevator addressing in the ATS system.

Door number Elevator number

DGP address

Remarks

1-16 None 16 The RAS stations of the control panel – unidirectional door control

17-20 17-20 1

21-24 21-24 2

25-28 25-28 3

29-32 29-32 4

ATS1250/60 Access control DGP:

Bi-directional door control,


33-36 33-36 5

37-40 37-40 6

41-44 41-44 7

45-48 45-48 8

49-52 49-52 9

53-56 53-56 10

57-60 57-60 11

61-64 61-64 12

4.4.1 Basic Access Control in the Control Panel

The control panel has 16 RAS stations, of which every one can be used for unidirectional door control. Each RAS station is equipped with an exit button input, and a lock control output. The load of the outputs is limited to 50mA, so additional controlling equipment needs to be used. For that, the use of the ATS1340 connection box is recommended. It contains the appropriate connections to the system bus, power, RAS station, exit button, and executing devices. The control panel is not suited for powering the executing equipment (for example. electromagnetic locks), so the proper power supply needs to be included during the design phase.

The doors controlled by the RAS station can be monitored constantly by the alarm system, thanks to the programming option of suspending (shunting) the door zone. The access control system uses the same PIN codes, and the same devices as the alarm system. At the same time the access control devices can be used to control the alarm system. In particular, the card readers can use its user counting functions to change its state. Arming the system, for example, can be performed after the user uses the card three times while exiting.


9

10

8

9

10

Number Description

1 External power supply 12 or

2

3

24VDC

RS485 data bus

ATS system power supply12VDC – optional

4 Two alarm zones

5

6

Door open sensor – one alarm zone

Lock – with optional activation sensor

RAS station – reader or keyboard

Data bus output for additional devices – optional

Power output for additional devices

– optional

Drawing 4-4 Control panel based access control.

The doors controlled by the control panel have some functional limits. The advanced access control functions required in high security standard installations are not available.

The ATS1250 and ATS1260 are designed to implement those functions, controlling 4 doors and elevators respectively and providing all advanced access control functions.

Table 4-8 A selection of the most important access control functions.

Function

Card disarms the system and opens the door

Card x3 arms the system

Card valid if are disarmed

Power supply with battery back-up for executing equipment

Card formats

Two cards to open door

PIN and card to open door

Two PIN and two cards to open door

Bi-directional passage control

Security level change outside of the time window

Card series

Locating the user on premises

Control Panel DGP ATS1250/60

Yes Yes

Yes

Yes

Yes

Yes

No Yes

Wiegand-26 or IUM mode 12 formats and IUM mode

No Yes

No

No

Yes

Yes

No

Only access or lack thereof

2

No

Yes

Yes

40

Yes

Lock chamber

Limiting the number of users on premises

Macro functions for access control

No Yes

No Yes

No Yes

4.4.2 Advanced Access Control of the ATS1250 DGP.

The ATS1250 controllers support 4 doors, and all the functions listed in Table 4-8. The devices are equipped with controlling circuits for the executing equipment, adequate power supply with battery support, and a set of inputs for providing the basic functions

(door monitoring, exit button etc.). By default, the ATS1250 is equipped with the basic memory expansion – ATS1830 – and 4 Wiegand interfaces. It enables the


64 implementation of all the basic access control functions without requiring additional expansions

The access control DGP– ATS1250/60 – stores a local copy of the user database and other settings pertaining to access control. This causes the reaction to the user presenting the card to be instantaneous even with a high number of users. The

ATS1831/32 IUM modules used with 17k and 67k users support not only the card learning functions but also the quick searching of the database. This causes the system to respond within less than 0.5s.

Table 4-9 basic parameters of the ATS1250 access control DGP.

Parameter

Number of doors

Number of interfaces on board

Number of readers

Local bus

Power supply

Value

4

4 – door entry readers 1 - 4 (local)

16 max.

RS485 – the same as system bus

4.5A

Lock outputs

Housing

Offline mode

Zones on board

2A@30V AC relay

ATS1642 – L

YES – full functionality

16 (by default assigned to: 4 door zones, 4 exit buttons,

4 DOTL zones, 4 reader blocking zones)

ATS1830 – interchangeable with IUM ATS1831/32

40

Memory

Card series

Database Local

Antipassback Local

The antipassback function requires passage control on both sides that require readers/keypads on both sides of the door. The access control DGP has a RS485 local bus interface, which supports connecting of up to 16 identification devices. Those can be the RAS stations of the ATS system having the RS485 inbuilt and other devices through the ATS1170 if they are compatible with the Wiegand interface. The device function is defined by its address on the local bus. The first four addresses double up as the reader inputs. This is important if the controller is further away from the readers than 70m – see the bus wiring in section 3.2.1. – that enables them to be installed as local bus components.

Table 4-10 Reader/RAS station addressing on the local bus.

Local passage address

RAS station local address

Input Output

Door 1

Door 2

1, 5

2, 6

9, 13

10, 14

Door 3 3, 7 11, 15

Door 4 4, 8 12, 16

Unused passage addresses can be used to install additional manipulators. The RAS station can be configured to emulate any control panel RAS station, to which the

ATS1250/60 DGP is connected. Such a device will work exactly like the emulated RAS station, not excluding event log entries. This functionality is especially interesting in cases when the number of manipulators of the control panel is not sufficient.

The ATS1250 DGP board outputs are, by default, configured for access control functions.

They support exit buttons, DOTL (Door Open Too Long) alarms, door monitoring etc.

Their use must me analysed based on the implemented access control functions. The table below contains the default zone mappings of the access control functions to local addresses for the ATS1250 DGP.

ATS Designers Guide

Table 4-11 Mapping zones to access control functions – local addressing.

Passage Open door blocked zone

Exit button DOTL Spare

Door 1

Door 2

1

4

3

6

16

15

2

5

Door 3 7 9 14 8

Door 10 12 13 11

4.4.3 Advanced Access Control of the ATS1260 DGP

The elevator controller uses 256 inputs and 256 local outputs. They are used to control the elevators buttons (inputs) and enforcing access rights for the floors (outputs) As the controller supports 64 floors and 4 elevators, it needs to have 256 inputs and outputs.

There are only 16 inputs on the controller’s board, so additional inputs need to be provided by expanders – access control DGP – installed on the local bus.

Besides monitoring the choice of a floor by the user, the inputs can be used to monitor the elevator, registering stopping/opening the elevator doors. Also in this case, the whole input address range is needed.

Elevator 1

Floor buttons

Input 64

Input 63

Input:

Input:

Input 5

Input 5

Input 4

Input 3

Input 2

Input 1

Access signal

Floor 64

Floor 63

Floor:

Floor:

Floor 6

Floor 5

Floor 4

Floor 3

Floor 2

Floor 1

Reader 1

Drawing 4-5 ATS1260 elevator control input and output diagram.

Mapping the inputs and outputs to a particular elevator can be found in Table 4-12.

Designing the local DGP is no different from designing the system bus devices. The same devices as well as the same approach are used.


Table 4-12 Mapping zones and outputs in the elevator controller.

Elevator – local address

Elevator 1

Elevator 2

Elevator 3

Elevator 4

First input

1

65

129

193

First zone

1

65

129

193

4.5 Cards and Readers

4.5.1 Advisor MASTER System Readers

The list of ATS system devices that can serve as user interface for access control is contained in Table 1-10. These are keyboards, readers, keyboards with integrated readers and the interface to connect other readers. Each of these devices can be used for user verification in access control and a significant simplification is the ability to connect them directly to the system or local bus. This decreases the complexity of the wiring and reduces the installation time. The smart cards and readers offered with the

ATS system deserve special attention. They have been described in detail in chapter

6. ATS system Smart Cards.

Often the system design guidelines contain specific requirements as to the type of access control cards and readers. The ATS systems can use any reader compatible with the

Wiegand hardware interface, and any card or token that sends a data stream of up to 48 bits. The details of using cards of different formats are described in paragraph 0. To connect a Wiegand interface reader to the ATS system the ATS1170 interface, or any of the reader outputs of the ATS1250/60 need to be used – it has to be kept in mind, that the maximum distance from the reader to the interface cannot exceed 70m, see section

3.2 which describes the wiring. The method of connecting the devices to the control panel

– the system bus – or access control DGP – local bus and ATS125 reader inputs – has been detailed in the following paragraphs.

4.5.2.1 HID

HID readers use the Wiegand interface. They can be used in the Advisor Master system by connecting them to the system, to the direct reader inputs of the access control DGP, or through the ATS1170 to the system bus, as well as the access control DGP local bus – see Drawing 4-6. This method can be used to connect any Wiegand interface reader..

Control panel

System bus

ATS1170 ATS1250/60 Local bus

ATS1170 ATS1170

66

Drawing 4-6 Connecting the Wiegand interface readers to the ATS system.

ATS Designers Guide

Besides hardware compatibility, the user card compatibility needs to be ensured. The

ATS system supports many access card formats - see Table 4-19 – but not all of them are supported by the control panel. The HID readers – see Table 4-13 – are compatible with the HID access control cards in the ATS Wiegand 32 bit format – see Table 4-14.

Cards of this format are supported by the ATS1250/60 DGP, which means it’s sufficient to program the card series for it to be active in the system. The control panel does not support this format directly so for them to be connected directly to the system bus, the

IUM option of the ATS system needs to be used. This means that each card in the system will have to be read during installation and stored in the user database.

Table 4-13 HID readers

Product

ACI730

ACI755

ACI757

ACI760

ACI765P

ACI775

ACI795

Description

Proximity card reader HID ProxPro Plus, range up to 20 cm, external

Proximity card reader HID ProxPro, range up to 20 cm, external

Proximity card reader HID ProxPro, range up to 20 cm, with keyboard

Proximity card reader HID ProxPoint, range 5cm, low cost

Proximity card reader HID MiniProx, range up to 10cm, miniature, external

Proximity card reader HID MaxiProx, range 70 cm, waterproof, external

Proximity card reader HID, range up to 14 cm, in flat housing, external .

(optional colour – white)

Table 4-14 HID cards


ACT725-xx Proximity card for HID ProxCardII readers

ACT736-xx Dual card DuoProxII (magn.+ proximity HID), thin (ISO), printable

ACT745-xx ProxKeyII key fob, for HID readers

ACT786-xx Proximity card for HID ISO ProxII readers , thin (ISO), printable

ACT790-xx Active proximity HID identifier (with battery) for vehicles, Dimensions: 10*7 cm

Table 4-15 Technical parameters of the HID readers.

HID Parameter ACI730 ACI755 ACI757 ACI760 ACI766 ACI775 795

Reader 7,6cm 14cm 73cm 14cm

Keyboard -

Voltage 10-28,5VDC 5-16VDC 5-16VDC 12/24VDC 5-16VDC

Power cons. 100mA

Power cons., max. 120mA

100mA

120mA

30mA

75mA

20mA

110mA

200mA

1,2A

20mA

115mA

Dimensions 190x190x23 127x127x25 79,6x43,7x17 152x43x25 300x300x25 119x76x17

Operating temp.

Operating freq.

-30 – 65 o

125kHz

C

Humidity 95%

4.5.2.2 MIFARE

MIFARE readers –Table 4-16 – are connected to the ATS system exactly like any other

Wiegand interface reader. (Ex. HID – see Drawing 4-6.) The offered readers are universal multi-protocol devices, identifying the MIFARE cards (smart cards) by the serial number of the card’s chip. Readers of this type – often called serial readers – are used to integrate an existing installation, based on MIFARE smart cards, with the Advisor

MASTER system.


The MIFARE card format - Table 4-17 – is not supported directly by any ATS module.

Therefore, to use cards of this type, the IUM function needs to be used. This function allows storing the data stream (up to 48 bits) of the card in the user database. To program the cards, all of them must be read.

Table 4-16 MIFARE readers

Product

ACI406

ACI407

Description

MIFARE proximity card reader (requires Wiegand interface and IUM module), external

MIFARE proximity card reader with keyboard (requires Wiegand interface and IUM module), external

Table 4-17 MIFARE cards

Product

ACT407

ACT430

Description

MIFARE standard card (25 cards pack)

MIFARE standard key fob

Table 4-18 Technical parameters of the readers.

MIFARE parameter ACI406 ACI407

Reader range 5-6cm 5-6cm

Operating Voltage

Power cons.

8-28.5VDC

100mA

Power cons., max. 100mA

Dimensions 110x43x24

Housing IP47

Operating temp. -40 – 55 o

C

Operating freq.

Humidity

13.56MHz

95%

4.5.3 Cards.

The ATS system supports many card types listed in the table below

Table 4-19 A list of available card formats.

Format

Wiegand 27 bit

Aritech ASC

Kastle 32 bit

Description Control Panel ATS1250/60

Used with Indala ESP type readers produced by ARITECH.

Used with ATS1190.

Kastle format cards.

Wiegand 26 bit (ID =

16, FC = 8)

Standard 26 bit Wiegand readers, along with ARITECH Wiegand readers. Has a 16 bit card number (0-65534) and 8 bit system code (0-255).

Indala ASC 27 bit Indala ASP proximity reader family, which uses a 27 bit Wiegand format

Indala ASC 26 bit Not used in Europe

Wiegand 32 bit 32 bit Wiegand format readers .Has a 16 bit card number and a 16 bit system code.

Mag.Card Aritech Aritech/TECOM magnetic card format.

Mag.Card Midas Midas magnetic card format.

C36 bit C36 bit card format.

ATS Wiegand 30 bit Aritech Wiegand 30 bit card format

x x x x

x

x x x x x x x x x


Format

ATS Wiegand 32 bit Aritech Wiegand 32 bit card format

Description Control Panel ATS1250/60 x

The control panel supports only formats supplied with the Advisor MASTER system. The flexibility of memory configurations of the system enables using all the cards mentioned in

Table 4-19 in the control panel as well as throughout the system. Using the IUM

Intelligent User Module and it’s emulation the system can store any data stream of up to

48 bits read from the card in it’s user database, regardless of it’s format or the reader type. All ATS1250/60 store a local copy of the user database, so all devices of this type need to be equipped with the same memory expansion as the control panel to which they are connected.


5 N

ETWORK

S

YSTEM

C

ONFIGURATION

Designing the alarm system described in this chapter consists of translating the design requirements to the number and type of control panels, optionally the expansions used to build the system. In the most general view, the design requirements for an integrated system are outlined in Table 4-1. Based on those parameters, assuming full use of the system address space, the number of control panels can be assessed – see Table 5-1 – keeping in mind the design limits. They consist mostly of alarm expansion configuration, that is using the alarm zone address space – see section 4.2 – and passage configuration – see section 4.4.

Table 5-1 Assessing the number of control panels in a networked system.

Parameter

Number of alarm zones

Number of areas

Number of users

Number of manipulators

Result–alarm requirements

Parameter

Number of unidirectional passages

Number of bi-directional passages

ATS4000/4518

ATS30/40/4518

Number_of_Control_Panels x 16


ATS3000

Number_of_Control_Panels x 256 Number_of_Control_Panels x 64

Number_of_Control_Panels x 16 Number_of_Control_Panels x 8

50 do 67000


Max. From above

50 do 11000


Max. From above

Comment

Simple unidirectional passages without additional functions

Bi-directional passages or advanced functions required see

Table 4-8

Result – AC requirements Max. From above

Total control panels: (Result–alarm requirements) + (Result–alarm requirements)

Depending on the expansions used, the maximum number of zones (unused zone address space) and doors supported by one control panel will change. In that case, the method of calculating the number of required control panels needs to be changed.

After finding the number of alarm zones, the appropriate zone and/or passage address range needs to be assigned to each, keeping in mind the control panel capabilities. After that the subsystems can be designed, as per paragraph 4.

Table 5-2 Capacity of the system with 64 ATS4000/4518 control panels.

Parameter Value Remarks

Alarm zones

Areas 1024

Users 67000 Identical user databases in each control panel

RAS stations

16384

1024

Unidirectional doors 1024

Bi-directional doors 3072

Completely expanded alarm system – 1024 unidirectional doors in the control panel manipulators, lack of advanced access control functions.

In certain situations the control panel manipulators can be doubled.

Control panel manipulators

Completely expanded access control system – 3072 alarm zones


6 ATS

SYSTEM

S

MART

C

ARDS

.

The Smart card technology is an integral part of the ATS system. The ATS product list contains a whole range of products (cards, readers, key fobs programmer, etc.) providing a complete access control solution. Card programming and reader support are an integral part of the TITAN software. The program is supplied with additional tools, card and user support functions (Photo ID, card customization and printing, etc.), which makes the solution interesting especially for small and medium systems, due to it’s attractive price, and flexibility of the solutions. An additional advantage of the solution is the autonomous mode capabilities of the ATS1190/92 readers, which can then work in credit applications, or be integrated with other access control, as well as working time registration systems.

6.1 Readers and cards

A set of readers can be easily adjusted for any application. The basic device is the

ATS1190 reader. It has a discreet, inconspicuous shape, a white colour, and five other colours are available by swapping the device cover. Applications that require a heightened mechanical or weather resistance of the reader can use the ATS1192 reader, functionally identical with the ATS1190. Although both devices have a robust design – the housing is filled with an elastic polymer, protecting the electronics from environmental influence and possible mechanical damage – the ATS1192 additionally has a reinforced housing. This allows the housing resistance to be declared at the IP54 level.

Table 6-1 List of available readers

Product

ATS1190

ATS1192

ATS1115

ATS1116

Description


High resistance proximity reader (does not require an interface) indoor/outdoor



Interface

RS485/Wiegand

RS485/Wiegand

RS485

RS485

Accessories

ATS166x Reader cover – 10 pcs. – available colours:

0-white, 1-red, 2-gray, 3-beige, 4-black

Complementing the offered readers is a wide range of cards and keyfobs. The cards conform to the ISO-Prox format and can be printed upon in all typical access card printers. Foreseeing the need to use the ATS system alongside other access control or time registration systems that use magnetic cards, we offer cards with a magnetic strip.

The strip isn’t programmed. Complementing the cards are three key fob types.

Table 6-2 Smart cards and key fobs.


ATS1471 Smart keyfob– 1pc.

ATS1473 Plastic smart keyfob–1pc.

ATS1475 Smart card, package – 10pcs.

ATS1476 Smart card with magnetic strip– 10pcs.

ATS1477 Smart keyfob package – 10pcs.


Table 6-3 Characteristic parameters of the Smart card readers.

Parameter

Reader range

Work temperature

Housing resistance

Current consumption

Value

ATS1190 ATS1192 ATS1115 ATS1116

6-12 cm

-35 – 60*C

IP54

30mA

6-8 cm

0 – 50*C

IP30

86mA

Output load

Credit applications Yes

50mA

NO*

*- a keyboard not connected to the system bus displays the ”System error” message

6.2 Programmer and software

The programmer is sold as ATS1621 and contains all necessary equipment for use:

• Programmer

• RS232 cables for computer connection

• Power supply

The software for accessing the programmer, and controlling all the aspects of work with smart cards is an integral part of the TITAN program. It’s equipped with a module for communication with the programmer, containing safeguards allowing only authorised users to access the equipment. It also contains the tools to program reader configuration cards, and a series of other additional functions and tools, not related directly with smart cards, but with cards in general:

• Photo ID module for gathering and storing user photographs;

• User verification capabilities – the information is retrieved form the database whenever the user passes a secure door.

• Card customisation module, with a template wizard, and support for printing cards with information contained in the system database.

• Credit applications – see section 6.3 below – a function allowing the readers to be used outside of the security system, to control other equipment (Xerox access, coffee, gym etc.)

6.3 Credit Applications

Each card contains four memory banks for storing credit units, access to four locations and priority. Each reader can be assigned to one of four locations with priority from one of the 16 levels, and the number of consumed credits. The reader output needs to be configured for credit applications to assure the desired response the user presenting the card. The reader doesn’t need to be connected to the system!

The user who received access rights to the location programmed in the reader will have the ability to use the device connected to the reader if his priority level is higher than the one programmed in the reader, and the number of credits on his card exceeds the number of credits withdrawn. Thanks to bi-directional communications card-reader, if the reader accepts the card, the proper changes to the amount of credits available are stored on it.

Using the TITAN software, the credit unit names and locations can be defined. This way, access to office equipment, canteens, gyms and other building facilities can be limited.

This function is available in the TITAN software without additional licences and payments.


6.4 Safeguards

Due to the sensitivity of the problem, the security of the system using the ATS Smart technology is detailed in a separate chapter.

The reasons, why the programmable card and reader solution might seem insecure are:

• Availability of software and equipment for generating new cards - the ability to generate a duplicate by unauthorised persons (external sabotage);

• The ability to program a duplicate of the card by an unauthorised employee (internal sabotage);

• Compromising security in case of card loss;

• Compromising security in case software and/or equipment (programmer) loss.

The ATS Smart card safeguards provide a high level of security for installations in which they are used.

•

Securing equipment against unauthorized access;

The programmer requires a password when connecting to the computer. The default password is blank and is not verified to simplify the process for new users. However if a password is used, the programmer will later require password authentication every time the connection is made. The connection password is stored only in the programmer which decreases the risk of revealing the password in case of a hacker attack or equipment loss.

There are two methods for deleting the programmer memory: software function or use of the programmer erasing card. Although the software function requires the programmer to be connected with the TITAN software, the use of the card allows the programmer memory to be deleted without a computer connection. Due to the possibility of losing the connection password (forgetting, disloyal employees etc.), it is recommended that an erasing card be supplied with every system that uses a programmer.

•

Card security;

The basic protection of the cards and readers is the 4 byte security code. It’s set in the programmer activation phase and is remembered in the computer profile and it’s internal memory. The card security code is stored in each programmed user and configuration card. The configuration cards, besides storing the programmed options in the accessed reader, also store the card security code. The reader ignores all tokens with a different security code than the one it’s programmed with. The reader-card configuration is bidirectional and encrypted. Every time the reader receives 112 bits of information from the card.

Each attempt to change a user card once it’s programmed requires password verification.

Only programming blank cards does not require authentication.

An additional safeguard is the option to block programming of the security code. By blocking the change of the code, erasing the card is also blocked.

The security code cannot be read either form the card or from the reader. It can only be read from the programmer, and only if an active connection to the TITAN software is present – activating such a connection requires authorisation.

The programmer profile contains the range of system codes and programmed cards for the current system/profile. The system will only accept cards that have the system codes from this range. This is an additional protection for systems in which the programmed cards are supplied by the installing technician. This solution is widely used in many countries as it allows reducing the system costs.

•

Card uniqueness.


Thanks to several safeguard parameters mentioned above:

• The security code of the card has 128

4

possible combinations.

• The values for the system codes can be from 0 to 2047

• The cards can have numbers from 1 to 65535

There are 3.6*10

16

different user cards.

A high level of uniqueness of each of the programmed card, along with the implemented safeguards, and limitations in the access to them, causes the card and reader system to provide a high level of security, taking into account all of the abovementioned risks.


7 T

ECHNICAL DESIGN DATA

.

Table 7-1 Available housings.

Dimensions

Housing Description

W L D

ATS1640

ATS1641

ATS1642

ATS1643

ATS1644

Dimensions in mm

Empty metal housing – size S

Empty metal housing – size M

Empty metal housing – size L

Empty metal housing for expanders

315

315

475

126

388

445

460

166

85

85

160

37

Empty polycarbonate housing for expanders 87 124 34

Table 7-2 Housing equipment.

Product

ATS1670

ATS1671

Description Trafo Trafo output voltage

Housing equipment for housing sizes S, M, L 58VA

Housing equipment for housing size L 120VA

24V AC

24V AC

Product

ATS1201

ATS1203

ATS1210

ATS1211

ATS1220

ATS1230

ATS1290

ATS1250

ATS2000

ATS3000

ATS4000

ATS4500

Table 7-3 Products delivered with housings.

Description Housing H. Equipment

Zone expansion DGP – 8 inputs (max.32) and 8 outputs (max.16) ATS1641 ATS1670

Zone expansion DGP – 8 inputs (max.32) and 8 outputs (max.32) ATS1641 ATS1670

Zone expansion DGP – 8 inputs and 8 outputs ATS1644

Zone expansion DGP – 8 inputs and 8 outputs

Zone expansion DGP – 4 inputs

Zone expansion DGP – 32 wireless devices

Zone expansion DGP – 32 addressable devices

Access Control DGP – 4 door controller

Control Panel 8 zones (max.32), 4 areas, dialer on board




ATS1643

ATS1644

Dedicated

ATS1244

ATS1642 ATS1671

ATS1640 ATS1670

ATS1640 ATS1670

ATS1641 ATS1670

ATS1642 ATS1671?

7.1.2 Space in Hosings.

Table 7-4 Battery configurations.

Housing ATS1640 ATS1641 ATS1642 ATS1642 Battery capacity

Device ATS2000 ATS4000 ATS4500 ATS1250

Battery configurations

BS127N

ATS3000 ATS1201/03

BS130N

BS131N

2xBS127N

BS129N x * x * x x 14,4Ah

2xBS129N x 52Ah

*- lack of space for expansions below Control Panel or DGP board.

Table 7-5 Space for expanders – Products delivered with housings.

Recommended configurations x x x x x


Housing

ATS1640

Product

ATS2000

ATS3000

ATS4000

Battery B BB B+ A

BS131N 4 2 2 1(2)

Other 6 3 4 1(2)

BS131N 2 1 0 0(1)

Other 4 2 2 1(2)

ATS1641

ATS1201/03

Other 8 4 4 2

ATS1250 - 6 3 4 2

ATS1642

() – dialer and communication devices (pcb A) can be mounted under Control Panel PCB

Table 7-6 Space for expanders – Empty housings.

Housing B BB B+ A C- C D

ATS1640 8 4 4 2 2 1 -

ATS1641 10 5 6(8) 3 2 1 -

ATS1642 12 6 8 5 4 2 2

ATS1643 - - 1 - - - -

ATS1644 - - 1 - - - -

7.1.3 Dimensions of devices PCB.

Table 7-7 Dimensions of devices PCB

Product

ATS1170

ATS1201

ATS1202

ATS1203

ATS1210

ATS1211

ATS1220

ATS1290

ATS1250

ATS1740

ATS1741

ATS1742

ATS1743

ATS1801

ATS1802

ATS1810

ATS1811

ATS1820

ATS1830

ATS7100

ATS7110

ATS7200

ATS7300

ATS2000

B

80x52 x x x x x x

BB

176x52

X

X

B+

80x90

A C- C D

80x176 130x200 202x218 218x254 x x x

Control Panels x x x x x x x x x x x x x


Product

ATS3000

ATS4000

ATS4500

B BB B+ A C- x

C x x

D

7.1.4 Control Panel and Memory configurations.

Table 7-8 Control Panel and Memory configurations.

Control

Panel

Zone q-ty

(on board)

ATS2000 32(8)

ATS2000 32(8)

ATS2000 32(8)

ATS2000 32(8)

ATS2000 32(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS3000 64(8)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4000 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

ATS4500 256(16)

Areas Event

Log

Access Control

Card Formats

Access

Control

Users.

IUM/Std. AYS1801

AYS1802

4

4

4

250 None (16 PIN) 50 Std.

50 Std.

50 Std.

4

4

8

8

8

250 F. supp. by ATS1250 48

250

250

F. supp. by ATS1250 16+48

Other up to 48-bit

250 None

16+48

(16 PIN)

50

50

50

IUM

IUM

Std.

50 Std.

50 Std. 250 F. supp. by ATS1250 48

8

8

250

250

F. supp. by ATS1250 16+48

Other up to 48-bit

8 1000 None

16+48

(16 PIN)

50

50

11k

IUM

IUM

Std.

8 1000 ATS/Wiegand 11k Std.



8

8

1000 F. supp. by ATS1250 16+48

1000 F. supp. by ATS1250 48

2k

11k

IUM

Std.

8

8

1000 F. supp. by ATS1250 48

1000 F. supp. by ATS1250 48

17k

65k

Std.

Std.

8

8

8

1000 Other up to 48-bit



16+48

16+48

16+48

2k

17k

65k

IUM

IUM

IUM

16

16

250 None

250 ATS/Wiegand

(16 50 Std.

50 Std.

16

16

16

250 F. supp. by ATS1250 48

250 F. supp. by ATS1250 16+48

250 Other up to 48-bit 16+48

50

50

50

Std.

IUM

IUM

16 1000 None




16 1000 F. supp. by ATS1250 16+48 2k IUM

16

16

1000 F. supp. by ATS1250 48

1000 F. supp. by ATS1250 48

11k

17k

Std.

Std.

16

16

16

1000 F. supp. by ATS1250 48



65k

2k

17k

Std.

IUM

IUM

16

16

16

16

16

16 1000 Other up to 48-bit

16 1000 None

16+48 65k IUM




16

16

1000 F. supp. by ATS1250 16+48

1000 F. supp. by ATS1250 48

2k

11k

IUM

Std.

1000 F. supp. by ATS1250 48

1000 F. supp. by ATS1250 48




16+48

16+48

16+48

17k

65k

2k

17k

65k

Std.

Std.

IUM

IUM

IUM

Memory

Expansion

N

N

N

N

N

Y

Y

Y

Y

Y

Y ATS1830

Y ATS1830

N ATS1831

N ATS1832

Y ATS1830

Y ATS1830

N

N

ATS1831

ATS1832

Y

N

N

Y

Y

ATS1830

ATS1831

ATS1832

Y

Y

Y

Y ATS1830

Y ATS1830

Y ATS1831

Y ATS1832

Y ATS1830

Y

Y

ATS1830

ATS1831

Y

Y

Y

Y

Y

ATS1832

ATS1830

ATS1831

ATS1832

Y

Y

Y

Y

Y

Y

Y ATS1831

Y ATS1832

Y

Y

ATS1831

ATS1832

ATS1831

ATS1832


Device

Table 7-9 ATS devices current consumption.

Connected

Expansion

Description

ATS1105

-

System keypad, LCD 2x16 character display,

8 area status LED with Wiegand reader interface

ATS1410

ATS1105 system keypad with ATS1410 magnetic card reader connected

Current cons. mA

Max. Typical

73

185

185

152

78

166

Required voltage V

Notes

All areas armed + Power status LED 220VAC

7,19 All areas armed + Power status LED 220VAC + LCD backlight

7,25


All areas armed + Power status LED 220VAC + LCD backlight

195 150

95

95

165

169

45

32

91

32

91

86

103

86

109

34

7,4

7,4

7,4

7,4

ATS1410 functions until keypad stops at 5.5Vdc





All areas armed + Power status LED 220VAC (reader operates until 8.5 VDC)

All areas armed + Power status LED 220VAC + LCD backlight (reader operates until 8.5 VDC)

All areas armed + Power status LED 220VAC (reader operates until 8.5 VDC)

All areas armed + Power status LED 220VAC + LCD backlight (reader operates until 8.5 VDC)

7,35 Each LED lit add: +9mA;

70 70 7,35


Device

Connected

Expansion

Description


Max. Typical


Notes

ATS1170

ATS1210/11

ATS1220

-

ATS1190

Wiegand reader interface, with proximity reader connected

-

Wiegand reader interface, PCB only

Zone expansion DGP – 8 inputs and 8 outputs

ATS1810 ATS1210/11 with 4 relays module connected

ATS1811 ATS1210/11 with 8 relays module connected

ATS1820 ATS1210/11 with 16OC module connected

- Zone expansion DGP – 4 inputs

ATS1290

-

PID bus

Zone expander DGP – addressable devices with

Point ID bus. Up to 32 devices.

ATS1290 with PID bus connected with max. load of

512UL

80

225

90

53

10

53

130

45 32

95 65

9,6

50 29 7,99

50 29 7,99

9

50

70

110

38

45

39

9,6

6,73 Sends „Low Voltage” message at 10,5VDC

9,6

All relays active. Minimum voltage to activate relays

10,1VDC. Pooling continues up to 5,5VDC.

6,73 All outputs active without any additional load.

6,73

7,48

All relays active. Minimum voltage to activate relays

10,3VDC. Pooling continues up to 5,5VDC.

ATS Designers Guide

Device

ATS1740

ATS1741

ATS1742

ATS1743

ATS1810

Connected

Expansion

Description

- ATS bus isolator/repeater – PCB

-

-

ATS bus converter RS485 / RS232 - PCB

ATS bus loop interface RS485 - PCB

ATS1201 DGP connected to bus loop

- ATS bus converter RS485/Fibber optic - PCB

- Output expansion module 4 relays (NO/NC) – PCB

ATS1811

ATS1820

ATS1801

-

-

-

Output expansion module 8 relays (NO/NC) – PCB

Output expansion module 16 OC – PCB

Computer and printer interface, 2 RS232 ports

ATS1802

ATS1830

ATS1831

ATS1832

ATS7100

ATS7200

ATS1410

-

-

-

-

-

-

-

Printer interface, RS232 port

Memory expansion module, 1MB

Memory expansion module, IUM, 4MB

Memory expansion module, IUM, 8MB

ISDN communicator, B-channel

ATS voice module, 2+6 messages

Magnetic cards reader


Max. Typical

90

100

86

155

60

60

100

86

97

36


4,75

6,1

6,79

10,24

Notes

100

250

50

60 All relays active

50 20 Prąd spoczynkowy

170

20

25 20

60 60

150 137

All relays active

Prąd spoczynkowy

One port communication

Two ports communication

20 60

100 60

Prąd spoczynkowy

One port communication

30

30

3

10

30 10

50 45

120 92

50 23

Prąd spoczynkowy

Connection active

110 20

2A

75 4,5

110mA current consumption during GSM transmission

Peek current consumption during connection negotiating

While card swipe.


7.1.6 Card Readers Technical Data.

Table 7-10 Proximity Readers Technical Data.

Parameter ATS MIFARE HID

Reading range

Keypad

Operating voltage

Current Cons.

Typical

Current Cons.

Max.

ATS1190 ATS1192 ATS1115/16 ACI406 ACI407 ACI730 ACI755 ACI757 ACI760 ACI766 ACI775 ACI795

6-12 cm 6-8 cm 5-6cm 5-6cm 25cm

- Tak

8-13,8VDC

29mA

20cm 7,6cm 14cm 73cm 14cm

9-13,8VDC

30mA 100mA 100mA 100mA 30mA 20mA 200mA 20mA

92x165x25 110x43x24 79,6x43,7x17 152x43x25 300x300x25 119x76x17

Operating temp. -35 – 60st.C 0 – 50st.C -40 – 55st.C

Humidity

Reading range for ACT7xx readers given for reader mounted on the diamagnetic surface and ACT724 card.

95%

-30 – 65st.C

125kHz


Datasheet | Aritech ATS4000 Technical data

GE

Security

Advisor MASTER integrated intrusion and access control system designers manual

ONTENTS

YSTEM COMPONENTS

1.1 Control panels

Common characteristics of the ATS system control panels:

Expansions:

1.2 User Interface

RAS stations characteristics:

1.3 DGP Expansion modules

1.4 System accessories

1.5 ATS8100 – TITAN Software

YSTEM POWER SUPPLY

2.1 System power supply

2.2 System equipment power consumption.

Several examples of power requirement calculations for expanded devices.

2.3 Wiring.

2.4 Connecting other power supplies.

ATS device with a power supply

PG822

OMMUNICATIONS

3.1 System bus

ATS Control

Panel

(DGP 16)

3.1.1 Wiring

3.2 Local bus

3.2.1 ATS1250/60 access control DGP

3.2.2 ATS1290 addressable sensor DGP

3.2.4 ATS1105 and ATS1170 RAS station reader interface

3.3 PC connection.

3.3.2 PC direct connection

3.3.3 Increasing the range between the control panel and PC.

3.3.4 Modem connection

3.4 Control Panel Network

3.4.1 Control panel bus topology and wiring

3.4.2 Examples of CP networks connected by various communications interfaces.

3.5 Reporting events to the CS station

ONFIGURATION OF THE

DVISOR

NTEGRATED

YSTEM

4.1 Control panel selection and configuration

4.1.1 The procedure of selecting and configuring the alarm system control panel

4.2 Configuring the DGP expansion modules.

4.3 Areas

4.4 Access control

4.4.1 Basic Access Control in the Control Panel

4.4.2 Advanced Access Control of the ATS1250 DGP.

4.4.3 Advanced Access Control of the ATS1260 DGP

Elevator 1

4.5 Cards and Readers

4.5.1 Advisor MASTER System Readers

4.5.3 Cards.

ETWORK

YSTEM

ONFIGURATION

SYSTEM

MART

ARDS

6.1 Readers and cards

6.2 Programmer and software

6.3 Credit Applications

6.4 Safeguards

There are 3.6*10

different user cards.

ECHNICAL DESIGN DATA

7.1.2 Space in Hosings.

7.1.3 Dimensions of devices PCB.

7.1.4 Control Panel and Memory configurations.

Peek current consumption during connection negotiating

7.1.6 Card Readers Technical Data.

Key Features

Related manuals

Interlogix

AL-1206

Interlogix

AL-1291

There are 3.610*