advertisement
TABLE OF CONTENTS
TABLE OF CONTENTS ............... 1
DISCLAIMER ................................. 3
Copyright Notice ........................ 3
Trademark Disclaimer ................ 3
COMPLIANCE ............................... 4
Compliance Statements ............ 4
Statement .................................. 4
Statement .................................. 5
Japan Statements ...................... 5
Statements ................................ 5
BEFORE YOU START ................... 7
Instructions ................................ 7
THEORY OF OPERATION ............10
MYSTERIUM X ® Sensor ...........10
Image Processing .....................10
HDRx™ .....................................11
Magic Motion™ ........................12
Audio Recording .......................12
Inputs ........................................12
Line Level Analog Inputs ...........13
Video Monitoring Outputs .........13
Bomb EVF ............................13
RED LCD ..............................13
HD-SDI .................................13
HDMI ....................................13
RED LCD / Bomb EVF ® ............14
REDMOTE ® ...............................15
Digital Magazine (Media) ...........15
Metadata ..............................16
Conventions .........................16
SMPTE Timecode ................18
Power Consumption ............18
CONTROLS ..................................19
Brain .........................................19
Side SSD Module .....................20
Side Handle ..............................22
Top .......................................22
Front .....................................23
Rear ......................................24
Installation / Removal ...........26
DSMC Modules ........................28
Rear SSD Module.................28
Quad Battery Module ...........28
Dual Battery Module ............ 29
Removal ............................... 30
REDMOTE ................................ 34
Displays .................................... 36
EVF (OLED) .......................... 36
Touchscreen LCD ................ 37
BASIC OPERATION ..................... 38
Power Sources ......................... 38
Side Handle ......................... 38
Quad Battery Module .......... 39
XL ........................................ 39
QUICKPLATE ....................... 40
(DSMC) ................................ 41
External DC Power .............. 42
Power UP ............................. 43
Power Down ........................ 44
Graphical User Interface and Navigation ......................... 45
External Monitors ................. 45
Side Handle ......................... 51
REDMOTE ........................... 51
Navigating Menus .................... 52
Using Touchscreen LCD .......... 53
Touchscreen Shortcuts ....... 54
Power Down ........................ 55
Touchscreen Opreration ...... 56
UP YOUR RED EPIC .................... 57
Attach Power Source ............... 57
Battery ................................. 57
Quad Battery Module .......... 58
RED Brick ............................ 59
DC Power ............................ 59
Power UP ................................. 59
Preparing to Record ................. 59
Media ................................... 59
Calibration ........................... 61
Adjust Project Settings ........ 61
Recording ................................. 63
Record Indicator .................. 63
Playback ................................... 64
MENU CONTROLS ...................... 65
Adjustments ............................. 65
Adjustments ........................ 65
Advanced Setting Menus .... 66
MAIN MENU ................................ 67
FPS .......................................... 67
Varispeed ............................ 67
Basic Settings ..................... 68
Advanced Settings .............. 68
ISO (Sensitivity) ........................ 69
F Stop ...................................... 69
Exposure .................................. 71
Basic Settings ..................... 71
Advanced Settings .............. 72
White Balance .......................... 74
Basic Settings ..................... 74
Advanced Settings .............. 75
Resolution ................................ 77
REDcode .................................. 77
Various Frame Rates ........... 78
SECONDARY MENUS ................. 78
HDR Menu ............................... 78
HDR ON / OFF .................... 79
Stops ................................... 79
Focus Menu ............................. 79
Mode ................................... 80
Lenses ................................. 83
Zones .................................. 84
Lens Information Display ......... 87
+ Lens ................................. 87
Lens ..................................... 87
Exposure Menu ........................ 88
Presets Menu ........................... 88
Camera Presets ................... 88
LOOKs Presets .................... 92
Media Menu ............................. 93
Select Media ....................... 93
Format Media ...................... 93
Eject Media ......................... 94
Utilities................................. 95
Settings Menu .......................... 96
Display................................. 96
Look .................................. 108
Project ............................... 111
System Status ................... 114
Audio/Video ....................... 115
Setup ................................. 122
Maintenance ...................... 133
Playback ............................ 143
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
1
Power .....................................152
Power Status ......................152
Shutdown ...........................153
CAMERA FIRMWARE ................154
Firmware .................................154
Upgrade Procedure ................154
DIGITAL MEDIA ..........................155
Media ......................................155
Formatting Media ...................155
Status .....................................157
(Unmount) ...............................157
Touchscreen LCD ..............157
Using Side Handle .............158
Using Side SSD ..................158
Copying Media .......................158
Erasing Media .........................159
Macintosh OS X .................159
Windows ............................159
OUTPUT CONNECTORS ...........160
Camera Brain Front ................160
(Microphone Audio) ............161
Camera Brain Rear .................162
HD-SDI ...............................163
Headphone.........................164
SYNC (Video Sync) ............164
CTRL (RS232 Control) ........167
GIG-E (Ethernet) .................168
DC IN (Power Input) ...........169
HDMI Out ...........................170
Side SSD Module ...................171
REDMOTE ..............................172
RED EPIC ® Operation Guide
EPIC-M / EPIC-X
Version 3.2, Rev-A1
Functions ................................... 173
OPERATION ............................... 175
Display.................................... 175
Controls ............................. 175
Operation ............................... 178
Docking and Undocking .... 178
Power Up / Down .............. 179
Recording .......................... 181
Controls / Settings ............. 181
Menus ................................ 183
Maintenance ........................... 191
Internal Battery .................. 191
Firmware ............................ 193
OPERATION ............................... 206
Overview ................................ 206
Camera Setup ........................ 206
Master Camera .................. 206
Slave Camera .................... 207
Clip Naming Conventions ....... 207
ID) / Camera Position ......... 207
Connecting Cameras.............. 208
Operation ............................... 209
Changing Settings ............. 209
Recording .......................... 209
Power Down ...................... 209
ISO .............................................. 210
Underexposure (~ 2 stops) ..... 210
Overexposure (~ 2 stops) ....... 212
Appropriate Exposure ............ 215
Adjusting the ISO Rating ........ 218
PRODUCTION ........................... 220
Monitoring .............................. 220
REDCINE-X ® PRO ............. 221
MAINTENANCE ......................... 222
Cleaning ................................. 222
Exterior Surfaces ............... 222
Brain .................................. 222
Touchscreen) ..................... 222
EVF .................................... 223
REDMOTE Screen ............. 223
Lenses ............................... 223
Side Handle LCD ............... 223
Back Focus Adjustment ......... 224
TROUBLESHOOTING ............... 227
No Media Attached ................ 227
Error - Shutdown ................... 227
Applied ................................... 227
Camera Cannot Be Paired to REDMOTE ......................... 227
Touch Screen ......................... 227
Specifications............................ 228
Camera Brain Dimensions ..... 229
CHART ....................................... 233
APPENDIX M: MENU MAPS ..... 234
2
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
DISCLAIMER
RED ® has made every effort to provide clear and accurate information in this Operation Guide, which is provided solely for the user’s information. While thought to be accurate, the information in this document is provided strictly “as is” and RED will not be held responsible for issues arising from typographical errors or user’s interpretation of the language used herein that is different from that intended by RED. All safety and general information is subject to change as a result of changes in local, federal or other applicable laws.
RED reserves the right to revise this Operation Guide and make changes from time to time in the content hereof without obligation to notify any person of such revisions or changes. In no event shall RED, its employees or authorized agents be liable to you for any damages or losses, direct or indirect, arising from the use of any technical or operational information contained in this document.
For comments or questions specifically about the Operations Guide content, please send a detailed message to [email protected]
.
COPYRIGHT NOTICE
COPYRIGHT © 2012 RED Digital Cinema
All trademarks, trade names, logos, icons, images, written material, code, and product names used in association with the accompanying product are the copyrights, trademarks or other intellectual property owned and controlled exclusively by Red Digital Cinema.
TRADEMARK DISCLAIMER
All other company, brand and product names are trademarks or registered trademarks of their respective holders. RED has no affiliation to, is not associated or sponsored with, and has no express rights in thirdparty trademarks. MAC ® and QuickTime ® are registered trademarks of Apple, Inc. Intel ® is the registered trademark of Intel Corporation. Windows ® , Microsoft Windows ® and Windows Vista ® are the registered trademarks of Microsoft Corporation. AVID ® is a registered trademark of Avid Technology, Inc. NUKE is a trademark of The Foundry Visionmongers Ltd. Torx ® is a registered trademark of Textron, Inc. Canon ® and
EOS ® are registered trademarks of Canon Kabushiki Kaisha Corporation.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
3
COMPLIANCE
INDUSTRIAL CANADA EMISSION COMPLIANCE STATEMENTS
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment.
Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operations subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesirable interference.
CAUTION: If the device is changed or modified without permission from RED, the user may void his or her authority to operate the equipment.
4
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
AUSTRALIA AND NEW ZEALAND STATEMENT
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
EN 55022:2006
JAPAN STATEMENTS
This is a Class B product based on the standard of the Voluntary Control Council for
Interference (VCCI) for information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio interference.
Install and use the equipment according to the instruction manual.
EUROPEAN UNION COMPLIANCE STATEMENTS
RED declares that the equipment described in this document is in conformance with the requirements of the European Council EMC Directive 2004/108/EC, Low Voltage
Directive 2006/95/EC, RoHS Directive 2002/95/EC and WEEE Directive 2002/96/EC.
This declaration is based upon compliance of the product to the following standards:
• EN 55022, Information Technology Equipment - Radio Disturbance Characteristics
• EN 55024, Information Technology Equipment - Immunity Characteristics
• EN 61000-3-2, Limits for harmonic current emissions
• EN 61000-3-3, Limits for harmonic current emissions
• EN 60950-1, Information Technology Equipment – Safety
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
5
The Waste Electrical and Electronic Equipment (WEEE) mark applies only to countries within the European Union (EU) and Norway. This symbol on the product and accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product to designated collection points where it will be accepted free of charge. Alternatively, in some countries you may be able to return your products to your local retailer upon purchase of an equivalent new product.
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with you national legislation.
For business users in the European Union, if you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Responsible party:
Red Digital Cinema ®
34 Parker
Irvine, CA 92618
USA
6
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
BEFORE YOU START
Congratulations on your purchase of a RED DSMC ® Digital Still and Motion Camera.
Please read the attached safety instructions, and only then unpack the camera body and any accessories.
If there is any physical damage or missing components for either your camera body or any accessories, please file a support ticket at www.RED.com/support .
RED EPIC Digital Still and Motion Camera
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE USING YOUR CAMERA
A. Heed all cautions and warnings in these instructions.
B. Read these instructions before operating the camera and accessories.
C. Follow these instructions while operating the camera and accessories.
D. Keep these instructions with the camera and accessories at all times.
E. DO NOT attempt to modify, dismantle or open your camera, lens or other accessory as doing so may expose you to electric shock and serious injury. There are no user-serviceable parts inside. Alteration or repairs made to the camera, lens or other accessory, except by a RED authorized service facility, will void the Limited Warranty. Users are not permitted to make design changes or otherwise modify the operation of the camera, lenses or other accessories, without the express written approval of RED
DIGITAL CINEMA.
F. Only use attachments/accessories specified by RED.
G. Install camera and accessories in accordance with the manufacturer’s instructions.
H. Avoid imaging of laser beams as they may cause damage to the sensor.
I. DO NOT use the camera or accessories near water. Avoid exposing your camera to moisture. The unit is not waterproof, so contact with water could cause permanent damage to the unit as well as electric
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
7
shock and serious injury to the user. DO NOT use the camera in the rain or under other conditions with high moisture without appropriate protection, and immediately remove power source if camera or accessories are exposed to moisture.
WARNING: To reduce the risk of fire or electric shock, do not expose the camera or accessories to rain or moisture.
J. DO NOT expose your camera to excessive vibration or impact (shock). Be careful not to drop your camera. Internal mechanisms may be damaged by severe shock. Mechanical alignment of optical elements may be affected by excessive vibration.
K. ELECTROMAGNETIC INTERFERENCE: The use of devices using radio or other communication waves may result in the malfunction or interference with the unit and/or with audio and video signals.
L. Clean only using a dry cloth. When cleaning your camera, remember that it is not waterproof and moisture can damage electronic circuitry. DO NOT rinse or immerse any element of the camera, lens or other accessory, keep them dry at all times. DO NOT use soaps, detergents, ammonia, alkaline cleaners, and abrasive cleaning compounds or solvents. These substances may damage lens coatings and electronic circuitry.
M. Maintain sufficient ventilation - DO NOT block any ventilation openings or obstruct cooling fan airflow.
CAUTION: Proper camera ventilation requires a minimum 1/2” (1,25cm) clearance between the camera ventilation openings and external surfaces. Verify that objects that can block the fan intake and exhaust ports do not impede airflow. Failure to permit adequate airflow may result in overheating of the camera, degraded operation and in extreme situations, damage to the camera.
N. DO NOT operate or store near any heat sources such as radiators, heat registers, stoves, or any other apparatus that produce heat. Store in a protected, level and ventilated place. Avoid exposure to temperature extremes, damp, severe vibration, strong magnetic fields, direct sunlight or local heat sources during storage. Remove any batteries from the camera before storage. Recommended storage and usage temperatures for your camera, lenses and other accessories are: a. Operating range: 0°C to +40°C (32°F to 104°F) o
Storage range: -20°C to +50°C (-4°F to 122°F)
If there are any performance issues with your camera or accessories when operating within this temperature range, please file a support ticket on www.RED.com/support .
O. The Side Handle, Side SSD Module, Rear Modules and Lens Mount are NOT HOT SWAPPABLE – meaning you cannot remove or install them while the camera is powered on. Before installing or removing any of these accessories, you MUST power down the camera. Failure to do so may result in damage to the accessory and / or camera brain that will not be covered under warranty.
P. Do not bypass the third prong of the grounding-type plug on the power cord of the AC Power
Adapter. A grounding-type plug has two blades and a third “grounding” prong. The third prong is provided for your safety. A grounding-type plug shall be connected to an outlet with a protective earthen connection. If the grounding-type plug does not fit into your outlet, do not attempt to modify the plug or outlet, consult a qualified electrician.
Q. Protect all power cords from being pinched, walked on or driven over by a vehicle. Replace any power cords suspected of sustaining damage due to crushing or other forms physical damage.
8
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
CAUTION: The power cord plug for the AC Power Adapter is used as the power disconnect. To disconnect all power from the AC Power Adapter, unplug the power cord plug from the wall outlet.
During use, the power cord plug should remain easily accessible at all times.
R. Lithium Ion batteries may be subject to special handling requirements pursuant to federal and local laws. Please refer to specific shipping instructions included with your battery regarding proper transport of your battery. Do not handle your battery if it is damaged or leaking. Disposal of batteries must be in accordance with local environmental regulations. For example, California law requires that all rechargeable batteries must be recycled by an authorized recycle center. Storing batteries fully charged or in high temperature, conditions may permanently reduce the life of the battery. Available battery capacity may also be temporarily lessened after storage in low temperature conditions.
WARNING: Do not expose the battery to excessive heat.
WARNING: Danger of explosion if an incorrect battery is charged with the RED Charger or is used to power the camera and accessories. Replace only with the same or equivalent type battery.
CAUTION: Refer all service and repair to qualified RED service personnel. To reduce the risk of electric shock, and damage to the camera or accessories, DO NOT attempt to perform any servicing other than any procedures that are recommended in the operating instructions.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
9
THEORY OF OPERATION
The RED family of Digital Still and Motion Cameras (DSMC) provide high performance digital imaging over a wide range of frame rates and optical formats including Super 35mm / APS-H. The RED DSMC camera is supplied as standard with a PL mount, and may be configured with mounts and 19 mm rods to accommodate most cinematography lenses, matte boxes and follow focus systems. Adaptors for 15mm offset studio and 15mm lightweight rods are also available.
In addition to compatibility with the majority of existing PL mount cinematography lenses; a select range of Super 35mm PL mount prime and zoom lenses are available from RED.
Other lens mounts, including the DSMC Canon mount are available, permitting the use of Canon EF and
EF-S photographic lenses. The Canon mount can report lens iris, focus and zoom data when mated to an appropriate lens. In addition, iris and manual or auto-focus settings may be controlled from the camera.
Lens mounts may be exchanged in the field, however it is highly recommended that this be performed in a dust-free environment, as the optical path will be exposed to the elements during this process.
A B4 mount to PL mount adaptor is also available to permit use of 2/3” HD broadcast lenses on the RED
DSMC camera. The optical coverage it provides is approximately equivalent to 16mm, hence the maximum recording resolution operating with a B4 mount 2/3” lens is 2K (2048 x 1152 pixels) progressive scan.
MYSTERIUM X
®
SENSOR
The MYSTERIUM X sensor has been specifically designed for use with the RED DSMC camera, and provides variable frame rate imaging at up to 120fps at 5K resolution, and up to 240 fps at 2K resolution.
Native color balance for the MYSTERIUM X sensor is 5,000 KELVIN, but it may be electronically compensated for any color temperature in the range 1,700 to 10,000 KELVIN. White balance preset values include Tungsten (3200K) and Daylight (5600K) light sources. The camera may also calculate a color neutralizing White Balance value on demand by imaging on a standard white or 18% grey card.
The MYSTERIUM X sensor includes high precision analog to digital conversion, capable of delivering up to 13.5 stops of dynamic range with daylight light sources over a camera sensitivity rating of 320-800 ISO.
In HDR mode, dynamic range can be extended to approximately 18 stops.
IMAGE PROCESSING
The digital image received from the sensor is formatted as a pixel defect corrected (but in all other aspects unprocessed) 12-bit, 14-bit or 16-bit per pixel RAW data frame. When operating in STILLS mode, each image received from the sensor is treated as a unique FRAME; however when operating in MOVIE mode, successive images received from the sensor are collected together into a CLIP. In all other regards, a frame of information gathered in STILLS mode or MOVIE mode is identical.
Each RAW frame or sequence of RAW frames in a clip is compressed using proprietary wavelet based
REDCODE ® RAW compression, then stored to a digital media Magazine such as REDMAG™ 1.8” SSD.
When recorded, the RAW data is independent of any RGB domain color processing such as ISO, White
Balance or other RGB color space adjustments made by the camera operator. These parameters are saved with the RAW data as reference METADATA; i.e. color is not burned into the recorded RAW data.
10
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
This recording technique permits RGB color processing choices to be deferred to post-production or to be adjusted in the field to help a director visualize alternative color treatments, without affecting the recorded RAW data’s image quality or dynamic range.
The camera’s monitoring path converts RAW sensor data to a white balanced 12-bit depth 2048 x 1080 pixel RGB 4:4:4 video signal. This signal may be modified using ISO, White Balance or other RGB color space adjustments as desired by the operator, and is then scaled and gamma corrected to provide
VIEWFINDER, HD-SDI and HDMI monitor outputs at 10-bit depth in 4:2:2 YCC or 8-bit depth in 4:4:4
RGB.
Frame guides and other camera data may be added as desired by the user to one or more of the outputs.
NOTE: The supplied REDCINE-X ® PRO application software can create and export .RMD “color look” files which may then be imported as camera monitor path color processing PRESETs. This information is stored as reference metadata, so that this color processing choice can be the default value used in Post-production. Refer to SECONDARY MENUS > PRESETS for details how to import and apply .RMD file metadata.
HDRX™
HDRx is an option for extending dynamic range up to 6 stops over the base Dynamic Range offered by the camera. When enabled HDRx simultaneously shoots two images of identical resolution and frame rate
- a normally exposed primary track (A-track), and an underexposed secondary track (X-track) whose exposure value reflects the additional stops of highlight protection desired. i.e. if you select an HDR value of +2 and your primary track exposure is 1/48th sec, the secondary track exposure will be 2 stops under, or 1/192 sec. The ISO and Aperture remain the same for both exposures.
During acquisition and recording, the two tracks are "motion-conjoined", meaning there is no gap in time between the two exposures. This is very important to note because if they were traditional alternating exposures, there would be a time gap between the two tracks that would show up as an undesirable motion artifact. Both tracks (A & X) are stored in a single .R3D
® file.
Since there are two exposures in HDRx mode, the camera is recording double the amount of frames each second. For example, when shooting at 24fps, the camera is recording two 24fps tracks, which is the data rate equivalent of 48fps; however after combining the A and X tracks in post-production you will see only one 24fps blended image sequence.
HDRx provides multiple options for exploitation in post-production.
• Blend the two tracks in post tools like REDCINE-X, Storm or any other application that supports the
SDK to create Magic Motion™. This blending of the two tracks comes with a slider so you can decide just how much of each track you want to use. A preview window shows you the combined result of your selection, or you can view each track individually.
• Combine the two tracks using MNMB (More Normal Motion Blur). MNMB is designed to emulate the motion of a traditional camera with full motion blur. This is a tool created by The Foundry that uses a new motion estimation algorithm designed specifically for HDRx. The shorter exposure (sharper image) is blended to match the motion blur of the normal exposure. Again, a preview window shows the combined result of your selection, or you can view each track individually.
• Use the X-track data for motion tracking, then combine the X-track with the A-track, or just motion stabilize the A-track using the motion analysis data extracted from the X-track.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
11
• Exporting to EXR file format will give you a multi-view EXR with both exposures (like a stereo EXR).
NOTE: If you ignore the X-track data, you will have a standard exposure with up to 13.5 stops of dynamic range just as if you had not enabled HDRx. For this reason, we encourage the A-track exposure to be "normal" as it provides the most options. If you are tempted to shoot "over-under", you are then fully committed to using HDRx and your post-production options are reduced.
NOTE: When recording in HDRx mode the camera records twice as many frames per second so the maximum frame rate or minimum REDCODE ratio, and the maximum record time on your media will be cut in half.
MAGIC MOTION™
Shooting at 24fps and with an 180 degree (1/48th) shutter on a film or digital camera may create an optical illusion we are familiar with, however it is not really the way the eye sees motion. To understand this, ask someone to stand in front of you and swing their arm over their head from one side to the other.
What you would observe in the recording is a constant motion blur until the arm stopped. What your eye sees though is both motion blur AND a sharper reference to the arm and hand all along the motion path.
"Magic Motion" provides such a combination of motion blur (A-track) and a sharper reference (X-track), with the bonus of extreme dynamic range not available with any other motion capture camera system.
AUDIO RECORDING
The RED DSMC camera can record up to two discreet channels of microphone level uncompressed 24bit, 48 KHz audio (four channels of microphone level or line level audio inputs when equipped with a PRO
I/O Module), that are synchronized with video and timecode to a REDMAG 1.8” SSD digital media
Magazine.
Input signals are routed via a high quality pre-amplifier and soft clip analog limiter in order to achieve the desired audio reference / recording level and maximize dynamic range.
To assist with audio reference level setup, the camera provides a color-coded Audio Level Meter in the
Graphical User Interface. Meter range is –36dBu to +20dBu (-56dBFS to 0dBFS) with audio input type, reference level and audio input clipping indicators.
Audio monitor output options include a 2-channel headphone output on the camera Brain and 2-channel line level analog outputs from the optional PRO I/O Module, plus 2-channel and 4-channel 24-bit 48KHz uncompressed digital audio embedded in the HD-SDI and HDMI outputs.
MICROPHONE LEVEL ANALOG INPUTS
The recording level of a Microphone input is affected by the sensitivity of the microphone and the Gain setting of the camera’s pre-amplifier. Available pre-amplifier range is +8dB to +62dB, with a default value of +10dB. The camera operator should choose a Gain value that aligns the input signal to the 0dBu reference line drawn on the camera’s Audio Level Meter (or the 0VU reference line if operating at that level).
This setting provides up to 30dB of input signal headroom above reference 0dBu level before clipping (up to 26dB above 0VU reference level) and maximizes the signal to noise ratio of the 24-bit digital recording.
12
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
LINE LEVEL ANALOG INPUTS
The recording level of a Line input is affected only by the signal provided by the field production sound mixer or other external line level source. The sound mixer operator should choose a mixer output level that aligns a reference tone signal to the 0dBu (-20dBFS) reference mark drawn on the camera’s Audio
Level Meter, or if using 0VU as reference level, a mixer output level that aligns a reference tone signal to the 0VU (-16dBFS) reference mark.
This setting provides up to 24dB of input signal headroom above reference 0dBu level before clipping (up to 20dB above 0VU reference level) and maximizes the signal to noise ratio of the 24-bit digital recording.
VIDEO MONITORING OUTPUTS
In its default configuration, the RED DSMC camera can simultaneously support one VIEWFINDER output
(suitable for use by a BOMB EVF ® , or RED LCD) plus one PROGRAM output and one PREVIEW output
(suitable for use by HDMI or HD-SDI monitors). The various monitor outputs can support a set of overlay graphics including camera GUI, timecode, clip name and framing guides; the specific overlay graphics for each type of output is user configurable.
The default VIEWFINDER output is the EVF / LCD connector located on the front face of the Side SSD
Module. If neither of these is connected, the VIEWFINDER output can be transferred to either the HDMI output or the HD-SDI output of the camera Brain.
BOMB EVF
A 1280 x 784 pixel progressive scan color display providing the equivalent of viewing a 17” reference monitor from a distance of about 3ft (1m). Display includes Surround View™ look around area, frame guides and safe action / title, zebra and false color exposure overlays, operation status and setup menus.
RED LCD
An 800 x 480 pixel progressive scan color display supporting a touchscreen overlay. Display includes
Surround View™ look around area, frame guides and safe action / title, zebra and false color exposure overlays, operation status and setup menus.
HD-SDI
A 720p or 1080p progressive scan output suitable for monitoring or recording to an external VTR or DDR device. May be configured for 10-bit LIN (VIDEO) or 10-bit LOG (FILM) encoded data.
HDMI
A 720p or 1080p progressive scan output suitable for monitoring via a PC monitor or most HDTV displays.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
13
Example of HDMI Monitor Output in MENUS mode.
RED LCD / BOMB EVF
®
The optional RED LCD and BOMB EVF are specialized video monitors that provide the user with a variety of tools to assist framing, focus and exposure, including:
-
Surround View™, which is an additional look around area, visible outside of the recorded image.
- Frame Guides, showing common film presentation and television aspects such as 2.40:1 and 16:9.
-
Focus, aided by high display resolution, 1:1 Focus Check function and False Color overlay.
-
Exposure, aided by dual Zebras, False Color overlay, RAW “Traffic Lights” and RGB histogram.
-
System information including current frame rate, ISO rating, shutter speed, color temperature, record resolution, record quality, clip name, timecode value and the remaining battery and media capacity.
For applications where use of an attached RED EVF or RED LCD is not desired – for example when working on a crane – the VIEWFINDER / MENU output can be transferred to the HD-SDI or HDMI outputs, supporting remote camera monitoring up to 200 ft away.
14
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
REDMOTE
®
REDMOTE is a camera control unit for RED’s family of DSMC cameras that attaches to the rear of the camera Brain or rearmost expansion module. REDMOTE may also be detached from the camera or rearmost module and provide wireless remote control of the camera over proprietary REDlink™ protocol.
Whether attached or operating via wireless, REDMOTE supports all controls necessary to operate the camera, including Record Start / Stop, Shutter Speed, White Balance, ISO and programmable User Keys.
A color LCD displays critical camera parameters, including media and battery capacity, timecode and clip name, lens data and exposure information.
REDMOTE LCD display
REDMOTE includes a rechargeable Li-Ion battery, which automatically re-charges when attached to the camera or rearmost module. It may also be re-charged by connecting to a USB 2.0 based power source such as a laptop PC or cell phone charger. Under typical operating conditions, REDMOTE should operate for up to 8 hours without requiring a re-charge and support a wireless communication range of approximately 50 ft.
DIGITAL MAGAZINE (MEDIA)
REDCODE RAW compressed MOVIE clips and STILL images; time code, multi-channel audio and metadata may be recorded to REDMAG 1.8” SSD solid-state digital media Magazine of 64GB, 128GB or
256GB capacity.
Each MOVIE clip is recorded with a unique name in a Clip folder with the extension .RDC. This folder contains all appropriate information describing the clip, including one or more REDCODE RAW.R3D files and all color grading metadata and other system level metadata such as lens and location information.
Refer to CLIP NAMING CONVENTIONS.
The individual Clip folders are placed into a Magazine folder (i.e. root directory) on the digital media. This
Magazine folder has the extension .RDM. As this folder contains all the recorded Clips; copying all clips recorded on the SSD to other media may be performed by a drag and drop operation on the .RDM folder.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
15
Typical Magazine Folder and clip structure
For additional information about digital magazines, refer to APPENDIX B: MANAGING DIGITAL MEDIA.
METADATA
RED’s family of DSMC cameras record the Metadata, which is data for each frame of the recording:
• Clip Name • s4i dynamic data • Copyright
• Time Code
• Date and GMT
• Lens and shutter speed / angle parameters
• Audio configuration
• Firmware version #
• GMT time/data
• RGB curves
• shadow control
• Luma curve
• Lens name, brand, ID, near focus, far focus
• Unit
• Camera Name
• Location
• Scene
• Take
• Accelerometer Data
• media serial #
• LTC user bits (3 32-bit word reg-dump from ISP)
• s4i static data
• Camera Network Name
• Production Name
• Director Name
• DP Name
• Gyro Data
CLIP NAMING CONVENTIONS
When you press RECORD, the camera automatically creates a unique name for the CLIP being recorded to the REDMAG 1.8” SSD media. The format of this name is:
Camera Letter + Reel Number + Month + Day e.g. A001_C002_0502**.RDC
16
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Where: A = camera A, 001 = reel 001, C002 = clip 002, and 0502 = May 02, and the digits * * are two random characters generated by the camera to prevent any possibility of duplicate names being created.
So a three Clip sequence of Clip Folders within a Magazine Folder on Camera A would look like this:
A001_C001_0502**.RDC A001_C002_0502**.RDC A001_C003_0502**.RDC
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
17
MULTI CAMERA SHOOTS
The scheme provides flexibility to uniquely identify Clips from different cameras on a multi-camera shoot.
For example three cameras, slated as camera A, camera B, and camera C respectively, can generate these easily recognizable clips on their respective digital media Magazines.
A001_C001_0502**.RDC B001_C001_0502**.RDC C001_C001_0502**.RDC
3D (STEREO) CAMERA SHOOTS
The scheme also allows unique identification of Clips from left and right eye cameras on a stereo shoot.
For example two cameras, both slated as Camera S, can generate these easily recognizable clips on their respective digital media Magazines.
S001_L001_0502**.RDC S001_R001_0502**.RDC
For more information refer to APPENDIX F: 3D SETUP / OPERATION > CLIP NAMING CONVENTIONS.
SMPTE TIMECODE
Time Code (TC) is a SMPTE timecode track that synchronizes to the camera’s high precision internal clock, or if operated in Jam Sync mode, references to an externally supplied SMPTE master timecode signal. TC is a sequential code that is continuous from frame to frame, but is discontinuous from clip to clip.
Edge Code (EC) is a SMPTE timecode track that always starts at 1.00.00.00 on the first frame recorded to the digital media. It is a sequential code that is continuous from frame to frame and also continuous from clip to clip. EC is equivalent to RUN RECORD commonly found on broadcast cameras.
Irrespective of the timecode mode selected, once recording starts the camera’s timecode counter will update at the same instantaneous frame rate as the recording. This ensures that a valid SMPTE timecode value is created for every frame in the clip, eliminating any timecode count jumps that could affect playback or editing.
If operating in Jam Sync mode referenced to an external timecode source, the clip’s master time reference point is the first frame of the recorded clip.
NOTE: When in Loop Record mode, Edge Code will also become discontinuous from clip to clip, because frames copied into the cache memory are discarded. This may lead to editing difficulties with post-production applications that assume continuous timecode.
POWER CONSUMPTION
The camera draws approximately 60 watts when recording in 4K resolution, 24fps MOVIE mode. The camera is cooled by convection from the camera body assisted by a fan contained in a sealed air duct.
Under typical operating conditions, a REDVOLT ® minutes and a REDVOLT ®
battery will run the camera and accessories for about 30
XL battery will run the camera and accessories for about 90 minutes.
18
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
CAMERA OPERATIONAL CONTROLS
This section describes the available operational controls on the RED DSMC camera Brain, Side SSD
Module, Side Handle and REDMOTE accessories.
BRAIN
A
A
C
B
A Power Status LED
B Power / Record Button
C Record Status LED
Power / Record Button / Status LEDs
• Power / Record Button: Powers camera Up / Down and initiates Record Stop / Start
• Power Status LED: Indicates Power status: o
LED Red = Power Present, Camera OFF o
LED Yellow = Power present, Camera Booting o
LED Green = Power present, Camera ON o
LED Green Blinking = Power present. Running on Battery o
LED Yellow Blinking = Power present. 5-10 minutes of Battery time left
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
19
o
LED Red Blinking = Power present. Less than 5 minutes of Battery time left
• Record Status LED: Indicates record status: o
LED Off = No Media present. o
LED Green = Ready to Record o
LED Red Constant = Recording o
LED Red Slow Blink = Recording, 25% Media Left o
LED Red Fast Blink = Recording, 5% Media Left o
LED Yellow = Finalizing
• Both LEDs: Indicates camera status: o
Both LEDs Green Blink = firmware update in Progress
SIDE SSD MODULE
REAR
E
FRONT
A
B
C
D
20
A
B
C
D
E
SSD Slot
User Key 1
User Key 2
Focus / Record Button
Media Indicator
Side SSD Module Controls
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
• SSD Slot: Slot for REDMAG 1.8” SSD digital media Magazine.
• User Key 1: Initiates user defined camera function. Undefined by Default.
• User Key 2: Initiates user defined camera function. Undefined by Default.
• User Key 1 + User Key 2 : Press both keys to Eject (unmount) REDMAG 1.8” SSD Magazine.
• Focus / Record Button: Touch for Auto Focus, fully depress to Start or Stop Record.
• Media Indicator LED: Indicates status of media: o
LED Off = No Media o
LED Green = Ready to Record o
LED Red Constant = Recording o
LED Red Slow Blink = Recording, 25% Media Left o
LED Red Fast Blink = Recording, 5% Media Left o
LED Yellow = Finalizing o
LED Yellow Blinking = Media Access (Format etc...)
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
21
SIDE HANDLE
TOP
B
A
C
E
D
F
A
B
C
Battery Release
Focus / Record Button
Adjustment Ring
D
E
F
LCD Menu Keys
LCD Display
LCD Backlight Button
RED Side Handle Controls - Top
• Battery Door Release Button: Releases Side Handle battery door to permit battery exchange.
• Focus / Record Button: Touch for Auto Focus, fully depress to Start or Stop Record.
• Adjustment Ring: Selects and adjusts camera parameter values. Similar to the scroll wheel on the navigation group.
• LCD Menu Keys: The specific functions for each key are defined by the LCD screen. Defaults are:
1 – ISO 2 – F-Stop 3 – Shutter Speed 4 – White Balance
• LCD Display: Displays key camera parameter values.
• LCD Backlight Button: Enables LCD backlight.
Note: Side Handle controls can be locked/unlocked by holding the 1 and 4 buttons simultaneously.
22
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
FRONT
A
Stills / Movie Slider A
Side Handle Controls - Front
• Stills / Movie Slider: Selects between STILLS and MOVIE modes of operation.
NOTE: This switch is not active at this time. Default camera operation is MOVIE
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
23
REAR
B
A
C
E
D
F
RED Side Handle Controls - Rear
A
B
C
MENU Button
Rocker Switch
Navigation Group
D
E
F
User Keys A-D
System Keys 1- 3
Thumbwheel Lock
• Menu Button: Press to access / camera setup menus.
• Rocker Switch: Increases or decreases selected value based on parameter selected in USER KEYs.
24
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
• Navigation Group: Allows navigation through camera menus, selection of camera parameter for adjustment, and adjustment of selected camera parameter.
C
A
B
Side Handle Navigation Group
A Scroll Wheel B Direction Keys C Enter Button o
Scroll Wheel: Selects and adjusts camera parameter value. o
Direction Keys: Navigates camera menus and may select parameter for adjustment. o
Enter Button: Confirms selected parameter value adjustment.
• User Keys: User Function Keys A-D. The specific function of these keys may be programmed by the user. Default settings for User Function Keys A-D are as follow:
-
User Key A – Toggles Focus Assist indicator
- User Key B – Performs White Balance calculation.
-
User Key C – Toggles False Color > 1:1 Magnify
-
User Key D – Toggles False Color > Exposure Check
• System Keys: Function is defined by System Firmware.
-
Upper: Toggles False Color > Exposure Check
-
Center: Not currently defined
-
Lower: Ejects (unmounts) the currently selected Media
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
25
INSTALLATION / REMOVAL
WARNING: THE SIDE HANDLE IS NOT HOT SWAPPABLE - MEANING YOU CANNOT REMOVE OR
INSTALL WHILE THE CAMERA IS POWERED ON. BEFORE INSTALLING OR REMOVING THE SIDE
HANDLE, YOU MUST POWER DOWN THE CAMERA. FAILURE TO DO SO MAY RESULT IN
DAMAGE TO THE SIDE HANDLE AND / OR CAMERA BRAIN THAT IS NOT COVERED BY
WARRANTY.
To install the side handle:
1. Power down the camera if necessary.
2. Remove the brain side plate (if installed) by removing the single screw located at the bottom.
3. Rotate upwards to disengage lip at top of side plate from camera brain.
Remove screw and rotate side plate upwards to remove.
4. Insert the lip at the top of the side handle into the area where the lip from the side plate was installed.
Insert lip into top of camera brain.
Press side handle flush against camera brain.
Rotate thumbscrew upwards until tight.
5. Rotate side handle down flush along side of camera brain.
6. Rotate thumbscrew upwards until tight. Ensure side handle is secure to camera brain. You may have to apply steady pressure to get the screw started.
26
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
To remove the side handle:
1. Power down the camera if necessary.
2. Rotate the thumbscrew downwards until detached from camera body.
Disengage lip from top of camera brain.
Rotate side handle upwards to remove.
Rotate thumbscrew downwards until loose.
3. Rotate upwards and pull down to disengage lip at top of side handle from camera brain.
4. Remove side handle from camera.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
27
DSMC MODULES
REAR
SSD
MODULE
The Rear SSD Module secures onto the back of the DSMC brain to serve as a rear location for recording onto 1.8" REDMAG SSD media.
QUAD BATTERY MODULE
• The QUAD MATTERY MODULE holds up to 4 REDVOLTs or 2 REDVOLT-XLs
• Batteries may be hot swapped
Battery Eject
Button
28
Quad Battery Module – Shown with REDVOLT batteries Installed
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
DUAL BATTERY MODULE
• The DUAL BATTERY MODULE holds up to 2 REDVOLTs
• Batteries may be hot swapped
Dual Battery Module – Shown with REDVOLT batteries Installed
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
29
MODULE INSTALLATION / REMOVAL
To install a DSCM Module to the camera, an Adaptor Plate must be purchased separately. The following procedure details installation of the Adaptor Plate and DSMC Module.
Install the Adapter Plate
1. Power down the camera.
2. Remove the REDMOTE.
3. Place the adapter plate over the v-mount on the rear of the camera brain.
4. Using a T-20 Torx, lightly tighten the four screws. Do not over tighten.
30
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
5. Tighten the screws again in a cross pattern until tight.
4 1
2 3
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
31
ATTACHING THE DSMC MODULE
WARNING: DSMC Modules are NOT hot swappable - meaning you cannot remove or install while the camera is powered on. Before installing or removing a Module, you MUST power down the camera. Failure to do so may result in damage to the Module and / or camera brain that is not covered by warranty.
Quad Battery Module shown.
1. Insert the lip at the top of the module into the recess at the top of the adaptor plate.
Rotate Module Down Until
Flush with Adaptor
Insert Lip At Top of Adaptor Plate
32
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
2. Rotate module down flush with the rear of the adaptor plate.
3. While applying steady pressure to hold the module against the adaptor plate, use a T-20 Torx screwdriver to rotate the lock on the adapter plate clockwise to secure the module.
Press Module Flush with Adaptor
Rotate Lock Clockwise
Until Red Dot Lines Up with Lock Icon
Installation is now complete.
To remove the DSMC Module and Adaptor Plate:
1. Power down the camera.
2. Use a T-20 Torx screwdriver to rotate the lock on the adapter plate to the Unlock position.
3. Rotate the module upwards and down to disengage lip at top of battery from adaptor plate.
4. Remove module from adapter plate.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
33
5. Use a T-20 to loosen the screws attaching the adaptor plate the camera brain.
6. Remove the adaptor plate from the camera brain.
REDMOTE
This section describes the physical controls on the REDMOTE. For complete details on REDMOTE control, refer to APPENDIX E: REDMOTE OPERATION.
IMPORTANT: For your REDMOTE to operate with this camera build version, ensure your REDMOTE has been upgraded to the latest firmware. Refer to APPENDIX E: REDMOTE OPERATION >
MAINTENANCE > UPGRADING REDMOTE FIRMWARE.
C
D
A L
K
E
H
I
B M
F
N
G
J
REDMOTE Controls
C
D
E
A Still/Motion Slider F
B Release Button (L) G
Record LED
Power LED
Rocker Switch
User Keys A-D
MENU Button
K
L
H Soft Menu Keys 1-3 M
I Navigation Group N
J Focus / Record Button
Soft Menu Keys 4-8
Power/Lock Slider
Release Button (L)
USB Connector
• Stills / Motion Slider: Allows selection of STILLS or MOVIE operational modes.
• Rocker Switch: Provides continuous adjustment of parameter specified in USER KEYS menu.
• User Keys: Press to initiate camera functions as defined in USER KEY menu.
34
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Default settings for User Function Keys A-D are as follow:
-
User Key A – Toggles Focus Assist Indicator
-
User Key B – Toggles False Color > RAW Check
- User Key C – Toggles False Color > 1:1 Magnify.
-
User Key D – Toggles False Color > Exposure Check
• Menu Button: Press to access / camera setup menus.
• Soft Menus Keys 1-3: Below the LCD are three (3) Soft Menu buttons 1-3 (H) whose functions are defined on the LCD screen. For complete information refer to APPENDIX E: REDMOTE OPERATION >
OPERATION > REDMOTE MENUS > SOFT MENU BUTTONS 1-3.
• Navigation Group: Allows navigation through camera menus, selection of camera parameter and adjustment of selected camera parameter.
C
A
B
REDMOTE Navigation Group
A Scroll Wheel B Direction Keys C Enter Button
-
Scroll Wheel: Selects and adjusts selected camera parameter value.
-
Direction Keys: Navigates camera menus and may select parameter for adjustment.
-
Enter Button: Confirms selected parameter value adjustment.
• Focus / Record Button: Touch for Auto Focus, fully depress to Start or Stop Record.
• Soft Menus Keys 4-8: To the right of the LCD are five Soft Menu buttons 4-8. These are pages displaying camera settings. For complete information refer to APPENDIX E: REDMOTE OPERATION >
OPERATION > REDMOTE MENUS > SOFT MENU BUTTONS 4-8.
• Power / Lock Slider: Slide and hold down for two seconds to power up / down REDMOTE and or camera. Slide up to lock keys.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
35
DISPLAYS
BOMB EVF AND BOMB EVF (OLED)
BOMB EVF is a high-definition, lightweight viewfinder that aligns quality performance with compact form factor.
• Resolution: 1280 (wide) x 784 (high) full-color
• Contrast Ratio: 1000:1 typical
• Available diopter range: +2.0 to -5.0.l
Talley Light
Focus Ring
Brightness Controls
RED BOMB EVF (OLED) brings advanced OLED technology into the field, providing truer blacks and more color accurate images
• Resolution: 1280 (wide) x 1024 (high) full-color
• Contrast Ratio: >10,00:1 typical
• Available diopter range: +2.0 to -5.0.l l
Focus Ring
Talley Light
Brightness Controls
NOTE: The specific function of EVF user keys (B/C) may be programmed by the user.
36
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
TOUCHSCREEN LCD
Red offers a five inch touch screen LCD with 800 X 400 resolution and 4:4:4 progressive scan. The touchscreen LCD allows navigation of camera menus and selection and adjustment of camera parameters by directly touching icons on the screen. Gestures supported include:
• Tap: Tap on an icon to bring up a quick adjustment display.
• Hold: Touch and hold on an icon to bring up an advanced interface display.
• Slide: Touch and slide on an icon to increment a value.
• Pinch: Touch with two fingers, then open or close to magnify or normalize the video image.
User Key 1
1:1 Magnify
Backlight Adjust
User Key 2
Exposure Check
RED 5” Touchscreen LCD Shown
NOTE: Default functions shown. All keys may be programmed by the user.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
37
BASIC OPERATION
This section describes basic operation, starting from power up, Viewfinder layout and Menu navigation.
WARNING: THE SIDE HANDLE, SIDE SSD MODULE, REAR MODULES AND LENS MOUNT ARE NOT
HOT SWAPPABLE – MEANING YOU CANNOT REMOVE OR INSTALL THEM WHILE THE CAMERA IS
POWERED ON. BEFORE INSTALLING OR REMOVING ANY OF THESE ACCESSORIES, YOU MUST
POWER DOWN THE CAMERA. FAILURE TO DO SO MAY RESULT IN DAMAGE TO THE
ACCESSORY AND / OR CAMERA BRAIN THAT WILL NOT BE COVERED UNDER WARRANTY.
Power draw is prioritized as follows when multiple power sources are available to the camera.
1. DC (Voltage) or Brick (%)
2. Battery Module batteries
3. Side Handle battery
POWER SOURCES
SIDE HANDLE
The optional Side Handle accepts one REDVOLT.
38
Side Handle Battery Compartment
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
QUAD BATTERY MODULE
The optional QUAD BATTERY MODULE accepts up to four REDVOLT or up to two REDVOLT XL batteries, which can power the camera and typical accessories.
REDVOLT AND REDVOLT XL
Quad Battery Module
REDVOLT and REDVOLT XL
Note: When multiple batteries are installed in the Quad Battery Module, the power management circuit will select the lowest charged battery to supply power to the camera. On depletion, a battery may be ejected from the Quad Battery Module for re-charging, and a new charged battery may be inserted in its place. i.e. batteries may be hot swapped, there is no need for the operator to power down the camera to replace a
REDVOLT battery when using the Quad Battery Module.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
39
BACKPACK QUICKPLATE
The optional BACKPACK QUICKPLATE attaches directly to the back of the DSMC BACKPACK to provide a compact REDBRICK configuration for EPIC or SCARLET-X.
Note: DSMC BACKPACK is required for use of the BACKPACK QUICKPLATE
BACKPACK QUICKPLATE
40
REDBRICK
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
AC POWER ADAPTOR - (DSMC)
AC POWER ADAPTOR - (DSMC)
When powering from the Module it is called in the lower UI as Rear Module (RM Bx) Bay number on lower
UI, and identified as Rear 1-4 in the POWER status menu.
In use, an LED on the Quad Battery Module will flash to show the battery currently powering the camera.
Current battery LED indicates status as follow:
• LED Off = No Battery
• LED Constant Green = Battery Not used but Charged
• LED Green Blinking = Battery Used (100% - 11%)
• LED Yellow Blinking = Battery has 10 minutes of run time remaining
• LED Red Blinking = Battery has 5 minutes of run time remaining
• LED Constant Red = Battery Discharged
Remaining batteries will have a steady LED on module.
When current battery reaches 4% charge, the battery module will automatically switch over another battery, by default the LOWEST charge capacity battery of the remaining batteries installed in the Module.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
41
Battery location and status are displayed in the lower UI. In this case RM B1 (Rear Module, Bay 1).
Battery location and status are also displayed on REDMOTE. In this case RM B3 (Rear Module, Bay 3).
The POWER menu also shows all installed batteries and their state of charge.
EXTERNAL DC POWER
RED DSMC Cameras accept input voltages between 11.5V - 17V D.C and can draw a maximum current of 12 Amps.
• An appropriate 150W supply with DC output rated at 15V 10A such as AC Power Adapter P/N 740-
0019 available from RED DIGITAL CINEMA.
• RED Charger. For RED Charger you must use 2B-to-1B Power Adapter Cable P/N 790-0138.
• RED BRICK ® 140Wh batteries may be used with Backpack Quickplate, RED Quickplate, Battery Belt
Clip, or RED Cradle via 2B-to-1B Power Adapter Cable P/N 790-0138.
• 4-pin XLR DC power sources may be used with the camera via adaptor cable P/N 790-0164.
42
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
POWER UP
Locate the camera’s Power / Record button on the right face of the Brain.
NOTE: This button also serves as a Record Start / Stop button once the camera is powered up.
A
C
B
A
A Power Status LED
B Power / Record Button
C Media Status LED
Power / Record Button / Status LEDs
When an appropriate power source is connected to the Brain, the Power Status LED will illuminate Red. If it is illuminated, depress and then release the Power / Record button. The Power Status LED will initially go out and within 5 seconds illuminate Orange to confirm the camera is powering up, then it will illuminate
Green, confirming the camera is powered up and ready to use.
If a formatted REDMAG 1.8” SSD is attached to the Brain, once powered up the Media Status LED will illuminate Green. If this LED is not illuminated, verify a formatted REDMAG 1.8” SSD is inserted into the
Side SSD Module and / or format the SSD if it has not previously been formatted on the camera.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
43
NOTE: Once powered up, if the Power Status LED illuminates Red, it indicates low remaining battery capacity and a battery exchange or switch over to external DC power is recommended.
POWER DOWN
The camera can be powered down in two ways:
1. Using REDMOTE or Side Handle Menu controls, or via Touch Screen LCD icons. Refer to
SECONDARY MENUS > POWER.
2. Depress and continue to hold the Power / Record button in its fully depressed position until the
INITIATING CAMERA SHUTDOWN shows on the display.
After Power Down, the Power Status LED will illuminate Red, if an appropriate power source is available.
44
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
GRAPHICAL USER INTERFACE AND NAVIGATION
RED LCD/TOUCHSCREEN LCD, BOMB EVF, EXTERNAL MONITORS
The following is a general description of the structure of the camera’s Graphical User Interface (GUI) which overlays the video monitor signal on the Viewfinder output(s) of the camera.
FRAME RATE ISO RATING F STOP SHUTTER SPEED WHITE BALANCE RESOLUTION QUALITY
LENS INFO
TITLE GUIDE
ACTION GUIDE
FRAME GUIDE
PICTURE CENTER / SPOT FOCUS
NEXT CLIP
FILENAME
OVERLAY GRID
TEMPERATURE
HDRx MODE
DROP
FALSE COLOR MODE
TC
REDMOTE
LAN
MEDIA
SOURCE / STATUS
TIMECODE
HISTOGRAM
RESOLUTION /
PROJECT
FRAME RATE /
QUALITY
RAW NOISE
LEVEL BAR
RAW CLIP
LEVEL BAR
RAW CLIP
METER
RIG STATUS
FAN
SPEED MAGNIFY
GENLOCK
SHUTTER SYNC
GUI Display Elements
The display elements include:
• Frame Rate: Current frame capture rate
• ISO Rating: Camera sensitivity
• F Stop: Functional when optional mount and lens are installed
POWER
SOURCE / STATUS
AUDIO METER
• Resolution Record Resolution
• Quality: REDCODE setting
• Lens Info: Lens information when using specific Canon or Cooke lenses.
• Shutter Speed: Exposure Time (or Degrees)
• White Balance: Color Temp
• Cursors: Reference cursors – Safe Action /
Safe Title, Picture Center, Grid Overlay
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
45
• Frame Guide: Record or Projection area
• Next Clip Filename: Filename of the clip that will be shot next
• Project Frame Rate: Current project TIME
BASE
• Noise Level Bar: Relative number of RAW pixels in noise
• Histogram: RGB Histogram.
• Clip Level Bar: Relative number of RAW pixels near clip
• Clip Meter: RGB sensor RAW clipping status
• Temperature: Displays camera sensor and core temperature in that order (xx/xxC)
• Drop: Indicates if any frames were dropped during recording of the clip
• Fan Speed: Displays fan speed in %
• HDR Mode: Displays HDRx mode status
• False Color Mode: Displays false color overlay mode
• Magnify: Tallies 1:1 if magnify is selected
• TC: Indicates presence of valid SMPTE timecode signal and Jam Sync status
• Genlock: Indicates presence of valid
Genlock signal / sensor sync to genlock
• Shutter Sync: Indicates shutter sync status
• RM: Indicates communication to REDMOTE
• LAN: Indicates communication via Ethernet connection
• RIG: Indicates 3D rig metadata is present
• Media Status: Media location and remaining media capacity in %
• Power: Indicates D.C supply voltage or % of remaining battery capacity Including current supply voltage
• Audio Meter: Audio input selection and levels
• Timecode: Current timecode value
• Menu ICON : In the upper Right corner on the touchscreen LCD - Opens the
Secondary Menus
• Playback ICON : In the upper Left corner on the touchscreen LCD - Accesses the
Playback Function
46
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
The GUI is broken down into the following three main sections: the Upper Status Row, the Live Action
Area, and the Lower Status Row. On VIEWFINDER output(s), all three sections are visible, on PREVIEW outputs only the Live Action Area and associated graphic overlays are visible. On PROGRAM outputs, none of the graphic overlays are visible, i.e. a PROGRAM output is defined to be a CLEAN FEED output.
UPPER STATUS ROW
Provides immediate feedback on the most critical image composition parameter settings, including (from
Left to Right):
• Playback Access (Touchscreen)
• Current frame capture rate
• ISO Rating
• Shutter Speed (or Shutter Angle)
• White Balance
• Record Resolution
• Record Quality
• Secondary Menus Access (Touchscreen)
Whichever parameter is underlined with a red bar may be immediately adjusted by pressing ENTER in the
Navigation Group of the Side Handle or REDMOTE, then using the Scroll Wheel to change the value of that parameter. To confirm the parameter change press ENTER a second time.
NOTE: Shutter angle is displayed in Relative mode by default, as indicated by Yellow text.
If the red bar is not on the parameter you wish to change, first use the Scroll Wheel to position the red bar under that parameter, then press ENTER, adjust with the Scroll Wheel and press ENTER a second time to confirm the value change.
In the above GUI example, the Scroll Wheel has been used to move the red cursor to the Shutter Speed parameter; and the ENTER key has been pressed. This reveals the Parameter Adjust Widow. Adjust the value using the Scroll Wheel and then press ENTER to confirm the value change, then close the submenu.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
47
LIVE ACTION AREA
Contains the recorded image area plus Surround View™ look around area, plus overlays for Frame Guide,
Safe Action / Safe Title and the current Clip Name and Timecode values. Each overlay may be color coded in one of 5 colors to maximize the contrast between the guide(s) and scene being captured.
LOWER STATUS ROW
The Lower Status Row provides feedback on key systems level camera values, including:
• Clip Settings
• Exposure (Histogram)
• Temperature, Power and Sync
• Media Status
• Power Status
• Audio Levels
ICON BEHAVIOR
TC
• TC Gray - No analog time code is currently detected.
• TC Red - Analog time code is being detected, but the use of it is not enabled.
• TC Green - Analog time code is being used to jam the time of day time code. TC will revert to gray if the signal is no longer detected.
48
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
GEN
• GEN Gray - No genlock signal is currently detected.
• GEN Green - A genlock signal compatible with the current project and monitor rates has been locked to.
SYNC
• SYNC Gray - The sensor sync mode is not Genlock.
• SYNC Red - The sensor sync mode is Genlock, but it is not locked to any genlock signal.
• SYNC Green - A genlock signal compatible with the current project and monitor rates has been locked to and the sensor timing is also locked to it.
• SYNC Yellow
POWER STATUS
If powering camera through DC power, the current voltage will be displayed.
If using a REDBRICK or similar external battery to power the camera through DC IN, power status displays the current supply voltage available from the battery. Supply voltage decreases as battery is discharged, the displayed text is color coded as follows:
• Green = 12.0 V and up • Yellow = 11.9 – 11.8 V • Red = 11.7 – 11.6 V
NOTE: The camera will automatically power down if supply voltage drops to 11.5 Volts.
If using a REDVOLT battery in the Side Handle or Battery Module to power the camera, power status displays the location of the power source (example: SH: Side Handle; RM: Rear Module) and reports the remaining battery capacity and the displayed text is color coded as follows:
• Green: >10 minutes • Yellow: 5-10 minutes • Red: <5 minutes
If using a RED BRICK battery connected to DC IN, power status displays BRICK and reports the % of remaining battery capacity and the displayed text is color coded as follows:
• Green: >10 minutes • Yellow: 5-10 minutes • Red: <5 minutes
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
49
RAW CLIP METER
The RAW Clip meter looks a traffic light style meter and indicates if either of the Red, Blue or
Green channels of the RAW sensor data are clipping. This meter is unaffected by White Balance,
ISO, VIEW or LOOK settings and therefore represents a true measurement of the exposure levels of the sensor at all times.
RAW NOISE LEVEL BAR
The RAW noise level bar displays the amount of pixels in the image that are in noise. For example, if the bar is about 1/8 of the total height, this would indicate approximately 1/8 of the total pixels in the image are at an exposure level at risk of displaying noise when pushed at higher ISO or FLUT values in postproduction.
RAW CLIP LEVEL BAR
The RAW clip level bar displays the amount of pixels in the image that are clipping. For example, if the bar is about 1/4 of the total height, this would indicate approximately 1/8 of the total pixels in the image are at an exposure level at risk of clipping and may not be recoverable by lowering ISO or FLUT values in postproduction.
50
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
SIDE HANDLE
As you navigate and adjust settings on the camera (main menu settings only), they will be reflected on the
Side Handle LCD display.
The display elements include:
• Power: Camera power status (DC Shown)
• Frame Rate: Image capture rate
• Resolution Recording Resolution
• Quality: REDCODE setting
• ISO Rating: Camera sensitivity
• Shutter Speed: Exposure Time (or Degrees)
• White Balance: Color Temp
REDMOTE
The display elements include:
• Camera ID: Displays camera ID (DEFAULT shown)
• Wireless Status: Displays signal strength when connected wirelessly
• Battery Indicator: Displays battery life or charge status (shown) of REDMOTE
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
• Resolution Recording Resolution
• Quality: REDCODE setting
• Frame Rate: Image capture rate
• ISO Rating: Camera sensitivity
51
• Frame Rate: Current frame capture rate
• Shutter Speed: Exposure Time (or Degrees)
• White Balance: Color Temp
• Resolution Record Resolution
• Quality: REDCODE setting
• Clip Filename: Filename of the clip that will be shot
• Project Frame Rate: Current project TIME
BASE
• Clip Meter: RGB sensor RAW clipping status
• HDR Mode: Displays HDRx mode status
• False Color Mode: Displays false color overlay mode
• Magnify: Tallies 1:1 if magnify is selected
• TC: Indicates presence of valid SMPTE timecode signal
• Gen: Indicates presence of valid Genlock signal
• Sync: Timecode Jam Sync status
• RIG: Indicates 3D rig metadata is present
• LAN: Indicates communication via Ethernet connection
• Media Status: Media location and remaining media capacity in %
• Power: Indicates D.C supply voltage or % of remaining battery capacity Including current supply voltage
• Audio Meter: Audio input selection and levels
• Timecode: Current timecode value
• Histogram: Displays histogram
NAVIGATING MENUS
The primary method to navigate Menus is via the Scroll Wheel on the REDMOTE or Side Handle. Rotate clockwise to move right, counter clockwise to move left. However, the Left and Right direction Navigation
Keys (REDMOTE or Side Handle) or Adjustment Ring (Side Handle) may also be used for this purpose.
The Up and Down direction Navigation Keys provide additional navigation functions when pressed:
UP Selects Advanced Settings menu.
DOWN Selects standard Settings menu.
As an example, position the Cursor under the Shutter Speed (24FPS) icon and press the UP Direction Key to access advanced adjustment values for Shutter Speed.
52
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
USING TOUCHSCREEN LCD
If operating a Touchscreen LCD, camera menu navigation may be made through finger gestures.
• To adjust a parameter value, simply touch it, and then swipe the finger left / right to adjust its value.
• To access an advanced parameter settings display, press and hold down on the parameter icon.
• Touch anywhere outside the overlay windows to enter the value changes and to hide the sub-menus.
• To enter the Secondary Menus, touch the MENU icon.
• To return to the Main Menus, touch the MENU icon again.
• To access the Playback function, touch the arrow.
• To exit the Playback function, touch the circle.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
53
TOUCHSCREEN SHORTCUTS
The bottom portion of the touchscreen contains shortcuts to the most-used camera screens.
54
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
POWER DOWN
NOTE: Camera will automatically power down if supply voltage drops to 11.5 Volts.
POWER MENU
1. Select the MENU icon
Menus. in the right corner of the Upper Status Bar to reveal the Secondary
2. Select POWER.
3. Select SHUTDOWN.
4. The camera will immediately power down.
USING POWER STATUS DISPLAY
1. Select the POWER status located between the audio channels and media remaining indicator, to reveal the same menu illustrated above.
2. Select SHUTDOWN.
3. The camera will immediately power down.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
55
LOCK / UNLOCK TOUCHSCREEN OPRERATION
LOCK
To lock out the touchscreen operation, touch and hold the MENU icon until the LOCK icon displays; indicating the touchscreen has been locked out. When locked, the main menu will be displayed.
UNLOCK
To unlock out the touchscreen and allow normal operation, touch and hold the LOCK icon until the
MENU icon displays; indicating the touchscreen has been unlocked.
56
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
FIRST TIME USE – SETTING UP YOUR RED EPIC
ATTACH POWER SOURCE
If a REDVOLT battery is installed in the Side Handle and DC power is connect through the DC IN connector, the DC IN power supply has priority and will power the camera instead of the battery.
BATTERY
Connect a RED battery to the camera in one of the following ways:
SIDE HANDLE
Attach a Side Handle and insert a REDVOLT battery.
INSTALL
A
C
B
1. Press the battery door release button (A).
2. Open battery door (B).
3. Press upwards on retainer (C).
4. Insert a REDVOLT battery until it is fully seated and retainer (C) clicks into place.
5. Close battery door.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
57
REMOVE
1. Press the battery door release button (A).
2. Open battery door (B).
3. Press upwards on retainer (C) to release battery.
4. Remove battery from side handle.
QUAD BATTERY MODULE
Attach a Quad Battery Module and insert one or more REDVOLT batteries.
INSTALL
Insert battery into desired location and press until a click is heard and battery is seated.
REMOVE
A
B
B
1. Press the battery eject button (A) for desired battery.
2. When battery pops out, remove battery from battery module (B).
58
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
RED BRICK
Attach to the camera using a V-Plate and 2B-to-1B Power Adapter Cable P/N 790-0138 to the DC IN connector.
DC POWER
Connect a DC power source to the camera in one of the following ways:
• Plug the RED AC Power Adapter into AC power, and the LEMO connector to the DC IN connector.
• Plug the RED CHARGER into AC power, and the LEMO connector to the DC IN connector via 2B-to-
1B Power Adapter Cable P/N 790-0138.
• Plug a 12V XLR based power source into the DC IN connector via adaptor cable P/N 790-0164.
NOTE: The maximum sustainable power load of the DSMC AC Power Adapter is 150W (15V@10A).
The output of the adapter is over current protected, and will shut down if an excess load condition occurs. If the output trips for any reason, remove any external loads from the camera, such as lights, motors etc, turn off the Adapter and repeat the above procedure.
POWER UP
Locate the camera’s Power ON / OFF button on the right face of the Brain. If the Power Status LED is illuminated Red, depress and then release the Power / Record button. If not illuminated, check your battery charge status or external power source cable connection. Once powered up the Power Status
LED will illuminate Green, confirming the camera is ready to use.
PREPARING TO RECORD
Before each days recording, the camera should be prepared as follows:
-
Physically set-up camera as desired.
-
Verify camera is using the latest firmware version at www.RED.com/support and if appropriate,
upgrade the camera firmware. Refer to APPENDIX A: UPGRADING CAMERA FIRMWARE.
-
Insert a blank (or previously used but erasable) REDMAG 1.8” SSD and format it.
-
Perform a BLACK SHADING CALIBRATION of the Sensor.
-
Check your PROJECT SETTINGS (Time Base, Record Resolution, Record Quality, etc.).
-
Frame, focus and record.
CONNECT AND FORMAT MEDIA
Identify a REDMAG 1.8” 64GB, 128GB or 256GB SSD that has not previously been recorded to, or is not a camera master and may therefore be erased and re-used. Aligned the RED logo of the SSD to the outside, and then push the SSD firmly, but without excessive force, into the slot in the Side SSD Module.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
59
NOTE: When fully inserted, the SSD media protrudes slightly from the SSD slot as indicated above.
When SSD media is inserted into the camera, the camera will recognize if the media is unformatted:
- On LCD, EVF and external monitors, in the media section of the GUI, NONE will be displayed twice (as opposed to when no media is inserted, the GUI displays NONE with three dashes below “---“).
-
On REDMOTE, NONE will be displayed twice (as opposed to when no media is inserted, the GUI displays NONE with three dashes below “---“).
-
On the Side Handle, NA will be displayed (same as if no media is present).
To format the media select SECONDARY MENUS > MEDIA > FORMAT MEDIA.
When FORMAT is selected, a FORMAT dialog box will appear allowing you to add Camera Identity and
3D Position properties when formatting. When desired options are set, select FORMAT.
NOTE: If any clips will be erased on the attached media, you will be informed of the number.
60
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
PERFORM A BLACK SHADING CALIBRATION
Refer to SECONDARY MENUS > SETTINGS > MAINTENANCE > CALIBRATION for complete details for performing a Black Shading Calibration.
ADJUST PROJECT SETTINGS
TIME BASE
To adjust the project TIME BASE, press the MENU button on the Side Handle or REDMOTE. Then use the
Scroll Wheel or Direction Keys to navigate to SETTINGS > PROJECT > TIME BASE and press ENTER.
Adjust to the desired value using the Scroll Wheel and press ENTER once more to confirm.
If using a Touch Screen, select SECONDARY MENUS > SETTINGS > PROJECT > TIME BASE. Adjust by sliding your finger up / down or tapping on the desired value, and then press anywhere else on the touch screen to confirm.
The following TIME BASES are currently available:
• 23.98 fps • 25.00 fps
• 24.00 fps • 29.97 fps
• 47.96 fps
• 48.00 fps
• 50.00 fps
• 59.94 fps
NOTE: A project can only support one Time Base as this defines the frame count to be used for time code and as the clip playback and editing frame rate. It is also the primary frame rate for acquisition, but variable speed (over-crank and under-crank) recordings can be made above and below this base frame rate using the VARISPEED menu.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
61
RECORD RESOLUTION
To adjust Record Resolution, navigate the Cursor to the RESOLUTION icon in the Upper Status Row and press the Navigation Group ENTER key. Adjust to the desired value using the Scroll Wheel and press
ENTER a second time to confirm.
If using a Touch Screen, press the RESOLUTION ICON, adjust RESOLUTION by sliding your finger left / right, or tap on the desired resolution, and then press anywhere else on the touch screen to confirm.
The following Recording Resolutions are currently available:
• 5K • 4K
• 5K HD
• 5K 2:1
• 5K WS
• 4K HD
• 3K
• 3K HD
• 2K HD
• 2K WS
• 1K HD
• 1K WS
• 5K ANA • 2K
RECORD QUALITY (REDCODE)
Allows adjustment of REDCODE settings.
Range is 3:1 to 18:1
Default is 8:1
Use the scroll ribbon to select a target REDCODE compression ratio.
The camera will automatically select the closest REDCODE to the desired target.
The display will always show the "current" compression ratio being used by the camera.
If the camera is able to achieve the desired target compression ratio, it will be displayed in white. If the camera is unable to achieve the target compression ratio, it will be displayed in yellow.
The current compression ratio will automatically be re-calculated when changes are made to Resolution,
FPS, HDRX Mode, Media, or Target REDCODE.
62
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
CAMERA ID (SLATE)
If operating on a multi-camera production, enter a different Camera ID for each camera; otherwise skip this step; the camera is ready to shoot.
The Camera ID is set when the media is formatted. Refer to ADVANCED MENU > MEDIA for details.
RECORDING
Ensure a formatted REDMAG 1.8” SSD is inserted in the camera’s Side SSD Module, then fully depress any one of the RECORD buttons located on the Brain, Side SSD Module, Side Handle or REDMOTE.
Fully depress again to stop recording. The camera will automatically create a unique and sequential file name for each clip recorded on the SSD based on the Camera’s I.D set in the MEDIA menu.
REDCODE RAW data recordings store the Color Temperature and Exposure (ISO) and any RGB color processing values you use in the monitor path as metadata. This metadata is used in REDCINE-X or other post-production software as initial white balance, exposure and color correction points however, you are free to change these values at any time when you process the RAW footage.
Time Code and Edge Code values used by the camera are Non Drop Frame (NDF); Drop Frame (DF) is not supported. Audio is captured uncompressed at 24-bit resolution, 48KHz sample rate per channel.
Digital media such as REDMAG 1.8” SSDs are very robust, but should be treated with equal care as exposed film or a videotape master. We recommend storing digital media that contains your footage in a secure location and backing up the data to a digital archival media, such as data tape or hard disk drive.
RECORD INDICATOR
When recording, the RED DSMC camera provides a variety of record indications (tallies):
-
Timecode, normally displayed in white colored text, will be displayed in red colored text.
-
A small Red dot will appear in the top right corner of the VIEWFINDER output(s).
- The REC LED on the right side of the camera Brain will illuminate Red.
-
REDMOTE upper LED will illuminate Red, and the Timecode will turn Red.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
63
-
If using a BOMB-EVF, the LED on the front will illuminate Red if Tally is enabled
-
SMPTE-RP188 timecode VITC-2 HANC metadata record flag will be enabled on HD-SDI outputs.
- If enabled in the USER KEYS menu, the GPO trigger output in the CNTL connector will pulse.
PLAYBACK
Playback is available on the RED DSMC Camera by going to SECONDARY MENUS > SETTINGS >
PLAYBACK or by touching the Playback arrow icon in the upper Left corner of the GUI.
The Playback function will display.
For complete details, go to SECONDARY MENUS > SETTINGS > PLAYBACK.
64
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
MENU CONTROLS
Displayed in the Upper Display Group of the VIEWFINDER output(s), are FRAMERATE (FPS),
EXPOSURE (ISO), _._ (F/Stop), WHITE BALANCE, RESOLUTION, and QUALITY (REDCODE). These parameters are adjustable directly through this screen. When using the touchscreen, directly to the right of these parameters is the MENU icon which when pressed will take you to the secondary camera set up menus.
ADJUSTMENTS
BASIC SETTING ADJUSTMENTS
SIDE HANDLE / REDMOTE
• The MENU button can be used to ENTER the secondary menus, as well as CANCEL inside lists and for navigating back up menus.
• Navigate to the desired setting using the NAVIGATION GROUP direction keys and press ENTER.
• Use the Scroll Wheel or Adjustment Ring to increase or decrease the parameter value.
• When the desired value has been selected, press ENTER to set.
BASIC ADJUSTMENTS USING SIDE HANDLE ONLY
Although not recommended, the Side Handle can be used stand alone to make basic adjustments to
FPS, ISO, Shutter Speed, Resolution and REDCODE located on the Main Menu screen. Use the
Navigation Group to make these adjustments while watching the cursor placement under the desired setting on the side handle LCD. When desired setting is selected, press the Enter button to access, then use the Scroll Wheel, Directional Pad or Adjustment Ring to make changes. When done, press the Enter button again to set the changed parameter. The MENU button can be used to ENTER the secondary menus, as well as CANCEL inside lists and for navigating back up menus.
TOUCHSCREEN
• The MENU ICON can be used to ENTER the secondary menus, as well as CANCEL inside lists and for navigating back up menus.
• Touch the desired parameter for adjustment.
• Slide your finger across the screen to scroll through the available parameter values.
• When desired the parameter value has been selected, touch anywhere in the screen area to set.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
65
• To close an alpha numeric keypad when entering information directly, tap anywhere on the screen outside the keypad.
ADVANCED SETTING MENUS
At this time, only FRAMERATE, F-STOP, SHUTTER SPEED and WHITE BALANCE on the MAIN MENU have advanced settings.
SIDE HANDLE / REDMOTE
1. Navigate to the desired setting using the NAVIGATION GROUP direction keys and then press the UP directional key.
2. Use the direction keys to navigate to the desired parameter adjustment field and press ENTER to confirm.
3. Use the Scroll Wheel to adjust the selected parameter value.
4. When desired selection is made, press the MENU button to set.
TOUCHSCREEN
1. Press and hold the desired parameter to gain access to advanced setting adjustments.
2. Press the field - a keypad type menu may appear to allow adjustments.
3. Press the desired parameter settings to adjust.
4. When desired selection is made, press anywhere in the screen area to set and exit the advanced settings submenu.
66
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
MAIN MENU
Available options under the MAIN MENU are FRAMERATE (FPS), ISO (SENSITIVITY), F STOP, 1/SEC
(EXPOSURE), WHITE BALANCE, RESOLUTION, and QUALITY (REDCODE).
FPS
Used to select an image capture frame rate that differs from the Project’s TIME BASE frame rate.
Ranges are as follows:
• 1 sec – 300 fps (2K 2.4:1)
• 1 sec – 120 fps (4K HD)
• 1 sec – 120 fps (5K 2.4:1)
• 1 sec – 96 fps (5K FF)
• 1 sec – 96 fps (5K ANA) • 1 sec – 96 fps (5K 2:1)
Default is 24 fps (or the selected Project TIME BASE frame rate if not 23.98 or 24.00 fps). 1 sec translates to 1 second per frame.
Available frame rate is dependent on Resolution and REDCODE settings. Refer to RECODE > REDCODE
OPTIONS FOR VARIOUS FRAME RATES table.
VARISPEED
When a frame rate other than the current TIME BASE has been selected, the FPS text will turn Yellow and VARISPEED will be shown where the Audio Meter is normally displayed at the lower right of the display.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
67
BASIC SETTINGS
Provides quick selection of the most common VARISPEED frame rates.
ADVANCED SETTINGS
When selected a numerical keypad will appear allowing the desired VARISPEED Framerate to be entered in 1 fps increments. Maximum frame rate is a function of RECORD RESOLUTION and
REDCODE settings. Granularity is 0.001 FPS.
On Touchscreen systems, a Keypad is available for direct numeric entry of the VARISPEED FPS value.
Touch the value bounded by the + and – labels to bring up, press outside the keypad to confirm the value.
68
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ISO (SENSITIVITY)
Adjusts the camera’s ISO rating. The sensitivity value is adjustable in 1/3 rd stop increments. When the
ISO rating is adjusted, the camera logs the change as metadata and the monitor path reacts accordingly. Higher ISO values lead to brighter images in the monitor path, and vice versa.
Range is ISO 250 – 12800
Default is ISO 800
F STOP
Aperture controls the depth of field of the subject imaged by the camera, and in combination with the shutter speed / angle setting controls the amount of light falling on the sensor. i.e. exposure. Increasing the F stop to a higher number reduces exposure as well as increases the depth of field, decreasing the F stop to a lower number increases the exposure and decreases the depth of field. You can chose either
1/3 or 1/4 stops.
RED DSMC Ti PL Mount Installed
When a lens equipped with Cooke’s S4/i system is attached to the DSMC Ti PL Mount, the camera will display the current aperture (F stop) of the attached lens. This is for information only and on-camera adjustment is NOT available, manual adjustment only as indicated by being Grayed out.
DSMC Canon Mount Installed
This menu will appear when a DSMC Canon Mount is installed and a Canon EF or EF-S Lens or equivalent is attached (a Non-Canon EF or EF-S Lens may not function as smoothly or accurately).
Adjusts the aperture (F stop) of the attached lens.
The attached lens for the example shown is a Canon EF 24-70mm.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
69
BASIC SETTINGS
Allows adjustment of the aperture (F stop) of the attached lens. The range will vary depending on the attached lens.
ADVANCED SETTINGS
When selected, the advanced settings menu allows fine control over the f-stop value under APERTURE and focal distance under FOCUS.
APERTURE (F STOP)
Provides the ability to enter the F stop value directly.
Range depends on attached lens.
Default depends on attached lens.
70
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
FOCUS
Provides the ability to enter the focal distance directly.
Range depends on attached lens.
Default depends on attached lens.
EXPOSURE
BASIC SETTINGS
Adjusts the exposure of each frame captured by the MYSTERIUM X sensor. Shutter speed presets are
provided for all common speeds (and shutter angles) for 24 / 25 fps and 50 / 60 fps project frame rates.
Decreasing Shutter Speed increases the amount of time over which light falls on the sensor, increasing exposure and motion blur on any objects moving within the frame. Increasing Shutter Speed shortens the amount of time over which light falls on the sensor, decreasing exposure and motion blur on objects moving within the frame.
Range is 1/24 th sec – 1/8000 th sec - Slowest available speed is 1 second per frame / frame rate, so for 24 fps it is 1/24 th sec.
Default is 1/48 th Sec.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
71
ADVANCED SETTINGS
When selected, the advanced settings menu allows fine control over the Exposure value, and permits entry in any of the three following common units – EXPOSURE (Shutter Speed), INTEGRATION TIME or
ABSOLUTE ANGLE (Shutter Angle).
EXPOSURE (SPEED)
Provides the ability to enter the Exposure value as a Shutter Speed (1/xx sec).
Range is 2 – 1/8000 th Sec - Slowest available speed is 1/frame rate, so for 24 fps it is 1/24 th Sec.
Default is 1/48 th Sec.
72
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
INTEGRATION TIME
Provides the ability to enter the Exposure value as a Shutter Integration Time (xx milliseconds).
Range is 0.125 to 41.708 mS (milliseconds)
Default is 20.833 MS
ABSOLUTE ANGLE
Provides the ability to enter the Exposure value as a Shutter Angle (xx Degrees).
Range is 1.000 to 360.000 Degrees
Default is 180.0 Degrees
As you adjust any of these three parameters, the camera will automatically calculate the equivalent value in the other units, but as a quick reference here are some common Speeds and Angles.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
73
To Convert Shutter Speed to Angle Equivalent:
Equivalent Degrees = (Shutter Speed x Frame Rate x 360)
E.g. = (1/48 x 24 x 360) = (8640/48) = 180
SHUTTER
1/32
1/48
1/50
1/60
1/96
DEGREES
270
180
172.8
144
90
SHUTTER
1/120
1/192
1/348
1/696
1/1000
Equivalent Shutter = 1 / (Frame Rate x 360 / Angle)
E.g. = 1/ (24 x 360/180) = 1/ (8640/180) = 1/48
DEGREES
270
180
172.8
144
90
SHUTTER
1/32
1/48
1/50
1/60
1/96
DEGREES
72
45
22.5
11
8.6
DEGREES
72
45
22.5
11
8.6
SHUTTER
1/120
1/192
1/348
1/696
1/1000
WHITE BALANCE
BASIC SETTINGS
Allows you to manually set Color Temperature in the range from 1,700 to 100,000 KELVIN.
Range is 1,700 K to 10,000 K.
Default is 5600K.
74
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ADVANCED SETTINGS
When selected, allows additional adjustment of the White Balance. Available options are PRESET,
COLOR TEMP, TINT, and CALCULATE WHITE BALANCE. Press APPLY PRESET for settings to take effect.
PRESET
Available preset options are:
SHADE
Preset to 9,000K
CLOUDY
Preset to 7,500K
DAYLIGHT
Preset to 5,600K
FLASH
Preset to 5,500K
FLOURESCENT
Preset to 4,500K
TUNGSTEN
Preset to 3,200K
INCANDECENT
Preset to 2,800K
COLOR TEMP
Allows you to manually set Color Temperature in the range from 1,700 to 100,000 KELVIN. Default is
5600K.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
75
TINT
Color Temperature calculations assume a pure light source that may not be true in the specific scene the camera is imaging. To compensate for any residual colorcast, the TINT parameter can adjust the
RGB color balance with a compensating Magenta - Green color component. Default is 0.000. When selected, a secondary keypad will appear allowing you to enter the desired Tint value directly.
NOTE: Selecting Calc White Balance calculates a new Tint value. This is maintained if the Color Temp is adjusted via the Color Temp parameter. If you select ANY presets, Tint will be reset to zero, which is the default value.
CALC WHITE BALANCE
The Calc White Balance function analyzes the central 25% of the image visible in the monitor to calculate a Color Temperature that will render a white object as white.
To use Calc White Balance function, place a White or Gray object under the ambient light, select the
Calc White Balance function and then press the Calc White Balance function box. Calc White Balance is also assigned to a User Key on the REDMOTE and Side Handle as a factory default setting.
76
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
RESOLUTION
Allows adjustment of resolution.
Default is 5K 2:1
FORMAT
1K WS
1K HD
2K WS
2K HD
2K
3K HD
3K
4K HD
4K
5K ANA
5K WS
5K 2:1
5K HD
5K
WIDTH (PX)
1280
1280
2048
1920
2048
2880
3072
3840
4096
3600
5120
5120
4800
5120
HEIGHT (PX)
480
720
854
1080
1080
1620
1620
2160
2160
2700
2160
2560
2700
2700
REDCODE
Allows adjustment of REDCODE settings.
Range is 3:1 to 18:1
Default is 8:1
Use the scroll ribbon to select a target REDCODE compression ratio.
The camera will automatically select the closest REDCODE to the desired target.
The display will always show the "current" compression ratio being used by the camera.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
77
If the camera is able to achieve the desired target compression ratio, it will be displayed in white. If the camera is unable to achieve the target compression ratio, it will be displayed in yellow.
The current compression ratio will automatically be re-calculated when changes are made to Resolution,
FPS, HDRX Mode, Media, or Target REDCODE.
REDCODE OPTIONS FOR VARIOUS FRAME RATES
Minimum frame rate is 1 sec per frame; maximum frame rate is a function of REDCODE setting, and record resolution:
5K
FF
5K
2:1
5k
ANA
5K
2.4:1
4K
HD
2K
2.4:1
FPS 24
RC
3:1
RC
3:1
RC
3:1
RC
3:1
RC
3:1
RC
3:1
25
RC
4:1
RC
3:1
RC
3:1
RC
3:1
RC
3:1
RC
3:1
48
RC
4:1
RC
5:1
RC
4:1
RC
3:1
RC
6:1
RC
6:1
30
RC
3:1
RC
3:1
RC
3:1
RC
3:1
RC
4:1
RC
4:1
60
RC
8:1
RC
8:1
RC
5:1
RC
6:1
RC
5:1
RC
3:1
50
RC
7:1
RC
6:1
RC
5:1
RC
5:1
RC
4:1
RC
3:1
75
RC
10:1
RC
9:1
RC
7:1
RC
8:1
RC
6:1
RC
3:1
72
RC
9:1
RC
9:1
RC
6:1
RC
8:1
RC
6:1
RC
3:1
90
RC
12:1
RC
11:1
RC
8:1
RC
9:1
RC
7:1
RC
3:1
96 100 120 150 175 210 250 288 300
RC
12:1
RC
12:1
RC
8:1
RC
10:1
RC
8:1
RC
3:1
-
-
-
RC
10:1
RC
8:1
RC
3:1
-
-
-
RC
12:1
RC
10:1
RC
3:1
-
-
-
-
-
RC
3:1
-
-
-
-
-
RC
3:1
-
-
-
-
-
RC
4:1
-
-
-
-
-
RC
5:1
-
-
-
-
-
RC
6:1
-
-
-
-
-
RC
7:1
SECONDARY MENUS
Press the Menu button on the REDMOTE / Side Handle or touch the MENU icon on the LCD to access the Secondary Menus.
Available options in this menu screen are HDR, FOCUS, PRESETS, MEDIA, SETTINGS, and POWER.
EXPOSURE is not implemented at this time.
HDR MENU
Available options are HDR OFF, HDRx and STOPS.
NOTE: HDR mode cannot be modified when in Magnify 1:1 mode.
78
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
HDR ON / OFF
By default, HDRx is OFF (HDR button is illuminated Blue). In the Lower Status Group of the Viewfinder screen, the HDR text is Gray, indicating HDRx is inactive.
To turn HDRx on, navigate to the HDRx button using the Navigation Group and press ENTER, or from the touchscreen directly touch the HDRx button. In the Lower Status Group of the Viewfinder screen, the
HDR text will turn White, indicating HDRx is active.
STOPS
To adjust the STOPS parameter, select the Stops box and use the UP / DOWN arrows to adjust.
Range is 1 to 6.
Default is 2.
FOCUS MENU
The Focus Menu is used to enable and select Focus parameters including MODE and ZONES.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
79
MODE
MANUAL FOCUS
To adjust the MODE parameter, select the Menu box and use the UP / DOWN arrows to adjust.
Available options are MANUAL and CONFIRM. Default is MANUAL.
MANUAL
When selected all focus operations are manual.
CONFIRM
Enables the Center or Spot focus square for use with manual focus. This mode provides additional focus assistance to the photographer using RED, YELLOW, and GREEN color changes to the focus spot window. Inadequate subject illumination and/or contrast may interfere with normal Focus Confirm operation.
For best results with Focus Confirm, operators should 'rock' the focus ring -- focusing through the point of optimum focusing and back again in decreasing amplitude -- as when 'zeroing-in' for precision manual focus.
AUTO FOCUS
NOTE: The following menus will ONLY appear if a DSMC Canon Mount is installed with a Canon or Sigma lens attached.
With a DSMC Canon Mount installed and a supported lens attached, available options become
MANUAL, CONFIRM, SINGLE, CONTINUOUS, TOUCH TRACK, and RACK. Default is MANUAL.
All settings except MANUAL place a single square (Center) or a single rectangle (Spot) on the screen
(depending on the ZONES selection) that indicate where the image is in focus.
Pressing the designated button for spot focus (REDMOTE / Side Handle button A default) will cycle you through each Focus Mode option in order as you press the button repeatedly.
80
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Performance of Auto Focus may be reduced under the following conditions:
• The subject is dark or distant.
• There is inadequate contrast between the subject and background.
• The scene has reflective highlights.
• The subject is backlit.
• There is inadequate surface contrast/detail inside the window.
NOTE: Edge Mode can be used for additional assistance in these conditions. Refer to SETTINGS
MENU > DISPLAY > TOOLS > EDGE.
MANUAL
When selected all focus operations are manual.
CONFIRM
Enables the Center or Spot focus square for use with manual focus. This mode provides additional focus assistance to the photographer using RED, YELLOW, and GREEN color changes to the focus spot window. Inadequate subject illumination and/or contrast may interfere with normal Focus Confirm operation.
For best results with Focus Confirm, operators should 'rock' the focus ring -- focusing through the point of optimum focusing and back again in decreasing amplitude -- as when 'zeroing-in' for precision manual focus.
SINGLE
A Focus / Record Button half-press performs single-shot AF. Optimized for rapid focus even under lowcontrast conditions. Works with both Center and Spot Zones.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
81
CONTINUOUS
Once engaged with half-press, will attempt to keep objects in AF window in focus. Works best with good lighting and contrast. Works with both Center and Spot Zones.
TOUCH TRACK
Dynamically updating positionable AF using touchscreen. Works with Spot Zone only. Keep AF Spot on subject while moving across frame, will continuously focus on spot.
RACK
For quickly selecting two focus points and executing rack focus between them. Focus points are selected using the Touchscreen. Shutter half-press executes rack movement. Works with Spot Zone only.
Rack mode remembers the last Center or Spot position and focus setting as the first rack point. A second rack point needs to be defined by moving the spot window to the desired second location. If the spot window is not moved, a shutter half-press will only cause the lens to execute a single AF adjustment on the original Spot. On the other hand, when two rack points have already been defined, the rack point can be updated by moving the spot to a new location. This will replace the rack point that is not in focus at that moment.
82
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
DSMC CANON MOUNT ELECTRONICALLY SUPPORTED LENSES
Canon EF 100-400mm f/4.5-5.6L IS
Canon EF 100mm f/2.0 USM
Canon EF 135mm f/2.0L
Canon EF 17-40mm f/4L
Canon EF 24mm f/1.4L II
Canon EF 24mm f/2.8
Canon EF 28mm f/2.8
Canon EF 35mm f/2
Canon EF 300mm f/4L IS
Canon EF 35mm f/1.4L
Canon EF 50mm f/1.2L
Canon EF 400mm f/5.6L
Canon EF 500mm f/4L IS
Canon EF 600mm f/4L IS
Canon EF 16-35mm f/2.8L II
Canon EF 200mm f/2.0L IS
Canon EF 200mm f/2.8L II
Canon EF 24-70mm f/2.8L
Canon EF 300mm f/2.8L IS
Canon EF 400mm f/2.8L IS
Canon EF 20mm f/2.8 USM
Canon EF 28mm f/1.8 USM
Canon EF 50mm f/1.4 USM
Canon EF 24-105mm f/4L IS
Canon EF 400mm f/4.0 DO IS
Canon EF 135mm f/2.8 Soft Focus
Canon EF 14mm f/2.8L II USM
Canon EF 15mm f/2.8 Fisheye
Canon EF 70-200mm f/2.8L IS
Canon EF 180mm f/3.5L Macro
Canon EF 28-300mm f/3.5-5.6L IS
Canon EF 100mm f/2.8L Macro IS USM
Canon EF 50mm f/2.5 Compact Macro
Canon EF 70-200mm f/2.8L IS II USM
Canon EF 70-200mm f/4L
Canon EF 70-300mm f/4-5.6 IS USM
Canon EF 70-300mm f/4.5-5.6 DO IS USM
Canon EF 800mm f/5.6L IS
Canon EF 85mm f/1.2L II
Canon EF 85mm f/1.8 USM
Canon EF-S 10-22mm f/3.5-4.5 USM
Canon EF-S 17-55mm f/2.8 IS USM
Canon EF-S 18-200mm f/3.5-5.6 IS
Canon EF-S 60mm f/2.8 Macro USM
Sigma 10-20mm f/3.5 EX DC HSM
Sigma 20mm f/1.8 EX DG ASP RF
Sigma 24-70mm f/2.8 IF EX DG HSM
Sigma 50mm f/1.4 EX DG HSM
Sigma 70-200mm f/2.8 EX DG APO Macro HSM II
Sigma 85mm f/1.4 EX DG HSM
Sigma APO 50-150mm f/2.8 II EX DC APO HSM
Zeiss Distagon T* 18mm f/3.5
Zeiss Distagon T* 21mm f/2.8
Zeiss Distagon T* 25mm f/2
Zeiss Distagon T* 28mm f/2
Zeiss Distagon T* 35mm f/2
Zeiss Planar 50mm f/1.4 ZE
Zeiss Makro-Planar 50mm f/2
Zeiss Planar T* 85mm f/1.4
Zeiss Makro-Planar 100mm f/2
Zeiss Distagon T* 18mm f/3.5
Zeiss Distagon T* 21mm f/2.8
Zeiss Distagon T* 25mm f/2
Zeiss Distagon T* 28mm f/2
Zeiss Distagon T* 35mm f/2
Zeiss Planar 50mm f/1.4 ZE
Zeiss Makro-Planar 50mm f/2
Zeiss Planar T* 85mm f/1.4
Zeiss Makro-Planar 100mm f/2
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
83
ZONES
Available options are CENTER and SPOT. Default is CENTER. This control allows selection of the boxes used to indicate objects in/out of focus.
CENTER
Provides a large, square target for focus. When objects located in the circle are in focus, the square will be Yellow or Green. When objects located in the square are out of focus, the square will be Red.
84
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
SPOT
Provides a small, square target for precise focus (similar to Center focus, only smaller). When objects located in the square are in focus, the square will be Yellow or Green. When objects located in the square are out of focus, the square will be Red.
SPOT FOCUS INDICATOR
Moving
The spot focus square can be moved around the screen.
Touchscreen
Tap on the spot focus square directly on the touchscreen and drag to the location you wish to relocate the spot focus circle.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
85
Side Handle / REDMOTE
1. Navigate to the focus menu.
2. Press the down arrow on the Navigation Group.
3. The spot focus square line weight will increase and the Red cursor under FOCUS will dim slightly.
4. Press the ENTER button.
5. Use the directional arrows to move the Spot Focus square to the desired location.
6. To exit:
-
Press the ENTER button, the spot focus square line weight will increase, then press the UP arrow to go back to the FOCUS menu.
-
Press the MENU button.
Resizing
The spot focus square can be resized using the Navigational Wheel or the Touchscreen.
Touchscreen
Tap two times on the square directly on the touchscreen to increase size. You can increase the size 3 times. After that, when you double-tap the spot focus square, it will decrease in size.
86
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
LENS INFORMATION DISPLAY
RED DSMC TI PL MOUNT + LENS
When a RED DSMC Ti PL Mount is installed and a Lens equipped with Cooke’s S4/i system (or equivalent is attached, the Focal Length and Focal Distance is displayed on the LCD, EVF and external monitors.
The focal length and focal distance values and range will vary depending on the attached lens. When the focal length or focal distance of the lens is manipulated, the current values are displayed.
DSMC CANON MOUNT + LENS
When a DSMC Canon Mount is installed, and a Canon EF or EF-S Lens or equivalent is attached, the
Focal Length and Focal Distance is displayed on the LCD, EVF and external monitors. When AF is set to
Manual or Confirm mode, the focus distance displays as a pair of Near - Far distances. When it is in AF mode, a single estimated Focus distance is displayed.
The focal length and focal distance values and range will vary depending on the attached lens. When the focal length of the lens is manipulated, the current value is displayed under Focal Length. The Focal
Distance can be changed under MAIN MENU > -.- (F-STOP) > ADVANCED SETTINGS.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
87
EXPOSURE MENU
Not implemented at this time.
PRESETS MENU
CAMERA PRESETS
Camera Presets are used to store and recall camera setup information such as LOOKs, key mappings,
I/O configuration, etc.
Your RED DSMC camera has a number of factory-installed settings.
APPLYING A PRESET
• Select
Presets
from the secondary menus
• Select the desired preset from the selection ribbon
• Press APPLY button
• Use the selection ribbon to selcet
Custom presets may be created to store groups of camera settings. For example; White Balance and
ISO settings for a particular shooting location can be captured and as a preset and easily recalled later.
Presets can also be saved on an SSD and applied to other RED DSMC cameras.
CREATING A PRESET
• Select
Presets
from the secondary menus
88
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
• Select
Create
and enter a name for the new preset using the QWERTY keyboard
• Press OK on keyboard to save the preset name
• Copy the desired settings from the left box of the interface to the right box using the
select one
(-->) or
select all
button
• Select and press
Create
button (upper right corner of the screen)
The preset has been created and is now stored on the camera.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
89
SHARING PRESETS
Presets may be shared between RED DSMC cameras using SSD media.
Camera to camera
90
Camera to multiple cameras
Select
Presets
from the secondary menu:
On Camera
On SSD
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
COPY PRESETS FROM CAMERA TO SSD
• Use scroll ribbon to select desired preset in camera box
• Use --> button to move the preset to the SSD box
COPY PRESETS FROM SSD TO CAMERA
• Use scroll ribbon to select desired preset in SSD box
• Use --> button to move the preset to the Camera box
• The following window will appear
• Select
Yes
to copy the preset to the camera and apply the setting
• Select No to copy the preset to the camera without applying the settings
MANAGING PRESET FILES
• The APPLY, DELETE, and CREATE buttons are only affect the camera box. Presets on the SSD will remain there until the media is reformatted.
• Copy the desired settings from the the
S-SSD\Presets
side of the interface to the
Camera
side using
select one
(-->) or
select all
button
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
91
LOOKS PRESETS
Look Presets allows you to save the specific color, image, white balance, and detail settings to be used for other projects. Meta is the default settings shot on the camera and cannot be deleted. As looks are created, they will be displayed alphabetically.
For detailed information on LOOKs, see the REDCINE-X Operation Guide, available on RED.com
92
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
MEDIA MENU
The Media Menu is used to format media (SSD) prior to use on the camera as well as to Eject (unmount) the media prior to removal from the camera. Available options when selected are SELECT MEDIA,
FORMAT MEDIA, EJECT MEDIA, and UTILITIES.
IMPORTANT: Media MUST be ejected from the camera before removal to prevent corruption and/or loss of data on media.
SELECT MEDIA
Allows you to select the Media location to be used by the camera. Default is the Side SSD (S-SSD)
Module.
FORMAT MEDIA
When selected, a new dialog box will appear allowing you to add properties to the media highlighted in the Current Media box when formatting. Available options are REEL NO, CAM ID, CAM POS, and
FORMAT to format the media with the values entered.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
93
NOTE: If clips are present on the media, you will be informed of how many clips will be erased when you format the media.
REEL NO.
When selected a keypad will appear allowing you to enter a value between 1 and 999.
CAMERA ID (SLATE)
Identifies the camera with a letter A through Z. Default is A.
CAMERA POS (POSITION)
Identifies the camera position as Right, Left or Center. Default is Center.
FORMAT
When selected, formats the media and adds the selected properties.
• During formatting, the camera will display “Formatting” with a Green status bar. REDMOTE will also display this message.
• When formatting is complete, camera will display “The magazine was successfully re-formatted. The digital magazine is ready for immediate use. REDMOTE will also display this message.
EJECT MEDIA
When selected will Eject (unmount) the media highlighted in the Select Media box.
When ejected, camera will display “Media Ejected Successfully”. REDMOTE will also display this message.
94
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
UTILITIES
Options are SECURE FORMAT.
SECURE FORMAT
Secure Format is a low-level format the rebuilds the SSD file system. It should only be used if the performance of the SSD is in question.
NOTE: If clips are present on the media, you will be informed of how many clips will be erased when you secure format the media.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
95
SETTINGS MENU
This section describes the various secondary controls available to configure the camera. Menu options are DISPLAY, LOOK, SENSOR, PROJECT, MODES, AUDIO/VIDEO, SETUP, MAINTENANCE, and
PLAYBACK.
DISPLAY
Available options are TOOLS, ZEBRA, OVERLAY, MODES, FRAME GUIDE, AREA GUIDES, and
MONITOR.
TOOLS
The Tools menu permits the operator to adjust the GUI elements displayed on the Viewfinder output(s)
Available options are OFF, EXPOSURE, FOCUS, VIDEO, EDGE, MAGNIFY, and RAW. The Dialog is available by either going to SETTINGS > DISPLAY > TOOLS or simply clicking on the histogram in the lower left.
OFF
Turns off any of the display modes in the first line.
96
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
EXPOSURE
This will show areas of under exposure (Purple) or over exposure (Red) on top of a monochrome image.
The color is based on RAW data so over/under exposure refers to data actually close to clipping in the sensor. When selected, the icon “E√” will be displayed in the Lower Status Group.
The EXPOSURE meter’s color bands provide the following information:
PURPLE
RED
Minimum Exposure
Maximum Exposure
Between minimum and maximum exposure values, the image is displayed as a monochrome image.
In the image, Purple areas represent sensor exposure levels that are likely to be noisy if gained up in post-production. Red areas represent sensor exposure levels that are at clipping.
NOTE: As EXPOSURE meters sensor RAW information, it is not affected by any RGB domain adjustments - such as ISO rating, FLUT, White Balance, Video Gain or other LOOK information.
NOTE: Because the RAW data represents a wider color space than RGB, provided that the Red
(clip) color is not present in EXPOSURE view, even if Red (clip) color is present in VIDEO view, the apparently clipped RGB highlights can be recovered in post-production by adjustment of ISO,
FLUT or changing the KNEE and WHITE values of the CURVE box.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
97
FOCUS
This will emphasize edges in the image without changing brightness/image content so it is easier to judge if the image is in focus. By adjusting your lens zoom and focus you can see which objects are coming into and falling out of focus. When selected, the icon “F√” will be displayed in the Lower Status
Group.
VIDEO
VIDEO displays a multi-color color overlay that allows you to check the video level of the RGB monitor path (calibrated to the SMPTE test signal) and any outputs driven from that path - such as HD-SDI and
HDMI. When selected, the icon “V√” will be displayed in the Lower Status Group.
Purple represents Super-Black, Dark Blue represents Black, Teal represents 3-stops under 18% Gray,
Green represents 18% Gray, Pink represents Skin Tone, Straw represents White, and Yellow, Orange and RED represent various degrees of signal clipping in RGB space.
By adjusting ISO, FLUT and Shadow while looking at VIDEO check, the operator can ensure that Black,
White and 18% Gray values conform to the desired levels on the HD-SDI and /or HDMI outputs.
The VIDEO bands provide the following information:
PURPLE
BLUE
TEAL
GREEN
PINK
STRAW
YELLOW
Super Black (IRE 1-0)
Black (IRE 1-3)
Dark Gray (IRE 9-12)
Typical Level for 18% Gray Card (IRE 44-47)
Typical level for Caucasian Skin (IRE 54-57)
White (IRE 96-98)
Super White (IRE 101-104)
98
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ORANGE
RED
Super White (IRE 105-107)
Super White (IRE 108-109)
At all other values, the monochrome image displayed represents the luminance value of the ISO adjusted image.
EDGE
EDGE displays a color overlay that outlines the edges of objects in an outline mode. By adjusting your lens zoom and focus you can pinpoint focus. When selected, the icon “F√” will be displayed in the
Lower Status Group.
WARNING: This will potentially interfere with recordings done via HDMI/HD-SDI in "Clean" Mode!
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
99
MAGNIFY
Magnify displays the central region of the sensor in 1:1 pixel resolution. When enabled, the 1:1 text in the
Lower Status Group will change to Green. If in Magnify mode, when the Record button is pressed, the system will automatically exit this mode. When using a touchscreen you can also perform this function by pinching your fingers together and apart.
NOTE: HDR mode cannot be modified when in Magnify 1:1 mode.
NOTE: When in magnify mode, you will not be able to adjust frame rate or resolution. These options will be Grayed out.
100
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
RAW
RAW displays the image without any ISO correction. When selected, OFF will be highlighted in the
Lower Status Group.
ZEBRA
Zebras enable and adjust the upper and lower values for two independent Zebra indicators. One zebra may be used for highlight exposure, and the other for mid tone or shadows. Zebras will be visible when in 1:1 zoom. By default, Zebra 1 and 2 are disabled.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
101
ZEBRA 1
To enable, select ZEBRA 1 check box. Areas of the image exposed within these ranges will be indicated by crosshatched overlays at - 45 degrees relative to vertical. Zebra 1 is shown in the image below.
High IRE
Change the desired setting between 93 and 109 (default is 108).
Low IRE
Change the desired setting between 75 and 107 (default is 99).
ZEBRA 2
To enable, select ZEBRA 2 check box. Areas of the image exposed within these ranges will be indicated by crosshatched overlays at + 45 degrees relative to vertical. Zebra 2 is shown in the image below.
High IRE
Change the desired setting between 1 and 99 (default is 47).
102
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Low IRE
Change the desired setting between 0 and 84 (default is 44).
OVERLAY
Allows you to enable and color code graphic overlays visible the on the Viewfinder and Preview outputs.
Use check boxes and pull down menus to control appearance of the overlays
Grid
The Grid display is shown below. The grid may be used as a “rule of thirds” indicator.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
103
Look Around
Highlights the look around area.
Overlay Elements
Lens Info
Motion Data
(Pitch & Roll)
104
File Name
Scene Name
01:17:06:16
Time Code
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
MODES
Available GUI display mode adjustments are Exposure, Shutter Mode, Aperture, and Focal Distance.
EXPOSURE
Selects GUI display of Shutter Exposure on Main screen as Time (1/xx sec) or Angle (Degrees). Default is
Time. Angle is shown below.
SHUTTER
Enables one of two shutter timing (duration) modes: Absolute or Relative. Default selection is Absolute.
Absolute
Shutter Speed is defined exclusively by the Shutter Speed setting.
NOTE: When operating in Absolute mode, the shutter speed is reported in White text.
Relative
Shutter Speed is defined by the requested Shutter Speed divided by the ratio of the current capture fps to the Project TIME BASE fps.
NOTE: When operating in Relative mode, the shutter speed is reported in Yellow text.
NOTE: If the operator requests a shutter speed that is outside the capability of the camera, the camera will automatically limit them when a limiting parameter changes.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
105
APERTURE
Selects GUI display of f/stop as 1/4 f Stop or 1/3 f Stop. Default is 1/3.
FOCAL DISTANCE
Allows you to set the Lens Info to display in Metric or Imperial measurements. Default is Imperial.
GUIDES
This sub-menu provides a selection of frame guides and safe action and safe title guides. User definable safe action and safe title guides may be saved as a USER PREFERENCE, thereby permitting the camera guides to be fully customized for any application. Available options are Size, Line Style, Color and
Transparency.
106
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
SIZE
Available options are Off, Full, 4:3, 16:9, 1.85:1, 1.9:1, 2.4:1, or User.
LINE STYLE
Available options are Solid, Dashed, or Bracket.
COLOR
Sets the frame guideline color to White, Gray, Teal, Purple, Yellow, Green, Blue, Red, or Black. Select the color that provides maximum color contrast with the scene you are shooting. Default is White.
TRANSPARANCY
Sets the frame guide transparency. Available options are 0%, 25%, 50%, 75% and 100%.
MONITOR
Allows you to modify brightness of the LCD and EVF parameters through Brightness Control. Also allows options for the LCD touchscreen to be changed through Touch Gestures.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
107
BRIGHTNESS CONTROL
Slide to the right for a brighter display; slide to the left for a dimmer display.
TOUCH GESTURES
These options apply ONLY to the Touchscreen LCD.
Pinch to Magnify
When selected, allows you to use two fingers in a pinching motion on the screen to enable Focus Zoom.
To zoom out to normal view, slide fingers apart.
Double-Click Right 25% to Record
When selected, the right 25% of the screen can be double-tapped to start and double-tapped again to stop recording.
Double-Click Left 25% to Start AF
When selected, the left 25% of the screen can be double-tapped to start the Auto focus (when DSMC
Canon Mount and compatible lens are installed).
LOOK
The LOOK menu permits adjustment of COLOR, GAIN, FLUT being recorded.
® , and CURVE metadata values. These parameters will affect the look of the monitor path, but do not affect the actual REDCODE RAW data
COLOR
The Color sub-menu permits adjustment of SATURATION, CONTRAST, and BRIGHTNESS.
SATURATION
Adjusts color saturation. Range is 0.0 (monochrome) to +3.8 (super color). Default is 1.0.
108
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
CONTRAST
Adjusts the overall contrast of the image. Range is -1.0 (flat) to +1.0 (max contrast). Default is 0.0.
BRIGHTNESS
Adjusts brightness without crushing highlights. Available range is – 10.0 to +10.0. Default is 0.0.
GAIN
The GAIN sub-menu permits adjustment of RED GAIN, BLUE GAIN and GREEN GAIN.
RED
Adjusts the gain of the RED channel only. Range is 0.0 (no Red) to 10.0. Default is 1.0.
BLUE
Adjusts the gain of the BLUE channel only. Range is 0.0 (no Blue) to 10.0. Default is 1.0.
GREEN
Adjusts the gain of the GREEN channel only. Range is 0.0 (no Green) to 10.0. Default is 1.0.
FLUT
The FLUT sub-menu permits adjustment of FLUT, EXPOSURE COMPENSATION and SHADOW.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
109
FLUT
FLUT (Floating Point Lookup Table) adjusts mid-range tone values. Range -8.0 to +8.0. Default is 0.0.
EXPOSURE
Adjusts exposure compensation. Available exposure range is –7.0 to +7.0. Default is 0.0.
SHADOW
Shadow adjusts the toe value of the FLUT or in other words, the tone near Black. Range is -2.0 to +2.0.
Default is 0.0. Increasing the Shadow value raises the video level of near Blacks. Lowering the Shadow value crushes the video level of near Blacks.
CURVES
The curves dialog box allows the user to set define curves for Luminance, and the red, green, and blue channels.
110
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
COLOR/GAMMA
The COLOR/GAMMA sub-menu permits adjustment of the monitor output Color Space and Gamma curves.
Available Color Space Options
Available Gama Space Options
PROJECT
The project menu sets the operating parameters the camera will use for a given project. Options available are TIME BASE and TIME CODE.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
111
TIME BASE
Sets the TIME BASE (fps) to be used for the project - the primary acquisition frame rate, time code count and playback & editing frame rate. Setting is displayed in the lower left corner of VIEWFINDER output(s).
Available options are 23.98, 24.00, 25.00, 29.97, 47.96, 48.00, 50.00, and 59.94. Default is 23.98.
TIME CODE
Selects the TIME CODE source to be used. Options are EXTERNAL TC and INTERNAL USER-
PROVIDED TC.
112
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
TIME CODE DISPLAY
Allows you to choose between TOD and Edge display.
TIME CODE SOURCE
Available options are EXTERNAL and USER-PROVIDED.
User-Provided
The three numerical boxes below allow you to set hours, minutes and seconds (in that order).
Use RTC Time
When selected the camera uses the cameras Real Time Clock as the timecode counter source
(snapshot of the RTC.)
Set Manually
When selected allows the user to define a custom value as the timecode counter seed.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
113
SLATE
When selected, a new dialog box will appear allowing you to add properties to the media highlighted in the Current Media box when formatting. Available options are CAM ID, CAM POS and SET to set the values entered.
Auto-Incrementing Take
If there is a value entered in the Scene box, the camera will automatically increment the take number every time the camera starts and stops recording.
Note: The scene name is limited to eight characters.
Scene Information Camera Information
Project Information Auto Slate Information
SYSTEM STATUS
Selecting System Status from the Project menu displays key project information.
114
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
AUDIO/VIDEO
Menu adjusts AUDIO INPUT, AUDIO OUTPUT, AUDIO CHANNELS, MONITOR CONTROL, and TEST
SIGNALS.
AUDIO INPUT
Allows you to enable / disable and adjust levels for audio inputs (CAM ANALOG). Default is unchecked.
Range 8 to 64 dB, default is 10 dB.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
115
You can also directly input your desired audio levels.
Audio channel level inputs are displayed in the lower section of the UI.
When audio is enabled and an audio jack is plugged in (detected by the camera), the circle next to CH1,
CH2 etc… will be Green and the box around the signal will be highlighted.
When audio is enabled and an audio jack is not plugged in (not detected by the camera), the circle will be Red.
Also, when audio is disabled and an audio jack is plugged in, the circle will remain Gray but the box around the signal will be highlighted (jack is detected by the camera).
116
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
AUDIO OUTPUT
Allows adjustment of audio output levels fed to the outputs. Available options for each channel are ON and MUTE. Default is ON at -9 dB.
AUDIO CHANNELS
Allows selection of audio inputs and operational modes.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
117
INPUT
Available inputs are CH 1/2 and CH 3/4.
NOTE: For cameras not equipped with a PRO I/O module, options are CH 1/2.
Source
Available options are NONE, CAM ANALOG, PRO I/O ANALOG, PRO I/O AES A, and PRO I/O AES B.
NOTE: For cameras not equipped with a PRO I/O module, options are NONE or CAM ANALOG.
Mode
Available options are UNBALANCED and BALANCED.
Link
Enables linkage between Channel Gain controls.
118
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Limiter
Enables signal limiter circuit. Limiter enabled adds 10dB of headroom for Microphone level inputs, or
4dB for Line Level inputs.
OUTPUT
Link
Enables linkage between Output Channel Attenuation controls.
MONITOR CONTROL
This sub-menu allows the monitor outputs settings to be modified. For changes to take effect, the camera MUST be restarted.
MODE
Allows you to choose the output for the LCD/EVF, HDMI and HD-SDI monitors.
LCD/EVF
Options are MENUS, PREVIEW, CLEAN, OVERLAY, 3D LEFT, and 3D RIGHT.
If anything other than MENUS is selected on the LCD (such as CLEAN), to return to displaying the
MENUS, perform a double-tap on the LCD screen.
HDMI
Options are OFF, MENUS, PREVIEW, CLEAN, OVERLAY, 3D LEFT, and 3D RIGHT.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
119
RES
Allows you to choose the output resolution for HDMI monitors. Available options are AUTO, 720p and
1080p.
NOTE: Some HDMI monitors may have trouble when "AUTO" is selected. In these cases, it is recommended to manually select the maximum monitor resolution provided.
HD-SDI
Options are OFF, MENUS, PREVIEW, CLEAN, OVERLAY, 3D LEFT, and 3D RIGHT.
RES
Allows you to choose the output resolution for HD-SDI monitors. Available options are AUTO, 720p and
1080p.
FREQ
Allows you to choose the output frequency in Hertz (Hz) for HD-SDI monitors. Available options are
AUTO, 23.976/24, 25, 29.976, 47.952/48, 50, and 59.94.
AUTOMATICALLY ASSIGN MENU SCREEN IF ENABLED
When checked will assign an attached external monitor to display the menus if none are selected.
120
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
TEST SIGNALS
Permits the video monitor outputs to be replaced with a video test pattern. Available test patterns are
CHIP CHART and SMPTE BARS.
To enable a desired test signal, select the desired test signal box. To exit the test signal, tap the touchscreen one time or press the Enter or Menu button on the Side Handle or REDMOTE.
CHIP CHART SMPTE BARS
NOTE: RED DSMC test signals are not recordable, they are provided to help align external video monitors connected via the HD-SDI or HDMI outputs.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
121
SETUP
This menu permits a variety of system setup tasks to be accomplished. Options available are KEYS /
SHORTCUTS, DATE / TIME, NETWORK, SERIAL, REMOTE, GPIO, and SYSTEM.
KEYS
Use Keys function to customize the assignment of DSMC camera controls.
KEY MAPPING
With Key Mapping, you press the button you want to change and follow on-screen instructions to complete the change.
When the Key Mapping tab is highlighted:
• Press the camera key you want to change.
• Use the pull down to select the desired function
• Press menu or a blank area of the touchscreen to save the setting
122
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
OPTIONS
• Select the desired option
• Press menu or a blank area of the touchscreen to save the setting
ADVANCED
• The advanced tab allows you to set key functions using a series of pull down menus
• Select Key Source (Brain, REDMOTE, Side SSD, etc.)
• Select the key you wish to change
• Select the desired key action
Key Source
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
123
User Key
Key Action
WARNING: Do not remap the navigation keys (Up, Down, Left, Right, Select (Enter), or Menu) on the side handle doing so could render the camera inoperabel.
124
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
DATE / TIME
This menu allows the user to reset the battery backed up internal clock of the camera. This time value is used as a timestamp on the .R3D files when recording to the RED MAG 1.8” SSD media.
NOTE: Enter time in 24-hour clock format. i.e. 2:35 pm should be entered as 14:35:00.
COMMUNICATION
Communication Menu allows you to set a unique identification for the camera (or a group of cameras) when operating in command and control communications network. Parameters are NAME, GROUP,
TARGET, set a SERIAL PROTOCOL, ENABLE DHCP, C2C or EXT, IP ADDRESS, NETMASK and
GATEWAY. Using the serial port or a direct Ethernet interconnect, two cameras, or one camera and one external device can be connected. If the camera is connected via Ethernet to a hub or router, multiple cameras and devices can communicate to each other.
NAME
Allows the user to create a unique camera NAME used in network communications
Note: the camera name field is limited to 8 characters.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
125
GROUP
A camera can also be identified as a member of a GROUP of devices. (For example, a group "3DRIG_A" could include two cameras "CAM_A_L" and "CAM_A_R"). The default group is named "DEFAULT".
Group names (like camera Names) can be used to uniquely address commands to a specific group of networked cameras. Note: the group name is limited to 8 characters, default name is DEFAULT.
TARGET
Using TARGET the user can specify if this camera can send commands to ALL devices on the network, to NONE of the devices on the network (meaning the camera will only listen to messages and not originate messages) or to a specific TARGET device - which can either be the NAME of a specific camera or device or a name of a GROUP of cameras or devices.
This structure allows for a lot of flexibility. For example on a multi-rig 3D shoot the user can either send commands to an individual camera (e.g. Set CAM_A_L to 1/48th exposure), to a group of cameras (e.g.
Set "3DRIG_A" to 48 FPS), or to all cameras (e.g. Start Recording on all cameras). It is important to note that with the exception of the NONE setting, all command filtering is happening on the receiver side of the communication link.
SERIAL PROTOCOL
The camera can communicate to external devices via RS232 Serial Port and / or the Gigabit Ethernet
Port.
This selection allows the user to specify the serial communications PROTOCOL. Available options are
NONE, ELEMENT TECHNICA, 3ALITY SPC 7100 and 3ALITY SPC 7000. Default is NONE.
126
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
NETWORK
If the Gigabit Ethernet port is used, additional settings are required. Each camera or device requires a unique IP ADDRESS. For simple camera-to-camera communication via Ethernet, both cameras need to be in the same sub-net.
Use the same sub-NETMASK and GATEWAY addresses and the first three groups of the IP address need to be the same.
In the example below, two cameras two cameras are assigned to the group “3D RIG.” Note the IP
Addresses.
Master
DHCP
If a DHCP-server is available in the communications network the DHCP option can be checked and the camera will obtain an IP
Address, Subnet Mask and Gateway address automatically from the DHCP -server.
C2C
If the camera-to-camera (C2C) check box is checked, changes to the settings on this camera will be sent out via the network as UDP packets as a SET command (Which then sets the property on other cameras). SET commands sent to this camera will not be propagated.
Slave
EXT
If the EXT check box is checked this camera can be controlled via TCP/IP from an external device.
IP Address
Permits the user to adjust the camera’s static IP address.
Netmask
Permits the user to adjust the Subnet Mask address.
Gateway
Permits the user to adjust the Gateway address.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
127
REDMOTE
This function is used to pair the camera to a REDMOTE for wireless operation.
SCAN AND PAIR REDMOTES
When selected, the camera will look for an attached REDMOTE, plus any REDMOTEs that are turned on with REDlink wireless enabled.
Available REDMOTES will appear in the left window.
The MAC Address for locally any attached REDMOTE will be in brackets <>.
Use the Pair and Unpair buttons to select and Pair/ Unpair REDMOTES.
MANUAL CHANNEL SELECT
The Manual Channel Select option allows the user to change the communication channel for the
REDLink wireless connection in the event of interference from other wireless devices. Auto (unchecked) will pick the "cleanest" channel automatically on each camera boot. Manual Channel Select is the default setting and for default uses Channel 0.
128
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
GPIO
GPIO selects the GPIO preferences sub-menu.
CAMERA INPUT
Permits the function of the SYNC IN / GPI pin in the SYNC connector to be defined as:
Sync In
Accepts an Input Sync signal to control Shutter Start timing.
General Purpose In
Accepts an Input Trigger signal to act as a General Purpose Input.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
129
CAMERA OUTPUT
Permits the function of the SYNC OUT / GPO pin in the CNTL connector to be defined as:
Sync Out
Provides an Output Sync signal to act as a Shutter Start tally.
General Purpose Out
Provides an Output Tally to act as a General Purpose Output tally signal.
130
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
SYNC MODE
Allows the shutter timing (scan start) to be synced to an external signal.
Available options are OFF, GENLOCK, SHUTTER, INTERNAL, PROXY, and SLAVE. Default is Off.
OFF – Shutter start time is defined by internal camera timing.
GENLOCK – Shutter start time is slaved to an external RS170A tri-level sync signal .a.k.a. “Genlock”.
SHUTTER – Shutter start time is slaved to an external Shutter Sync signal.
INTERNAL – Not implemented at this time.
PROXY – Not implemented at this time.
SLAVE – Not implemented at this time.
IMPORTANT: If Sync > Genlock mode is selected, DO NOT set fps to higher than 72fps, and to a speed NOT a multiple of the project base rate and genlock input.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
131
SYSTEM
Available options are FAN CONTROL, RECORD SPEED and STANDBY SPEED as well as BEEP
SPEAKER and EVF TALLY LIGHT.
FAN CONTROL
Specifies cooling fan operation. Available options are AUTO and MANUAL. Manual will run the fan at the speeds specified in RECORD SPEED and STANDBY SPEED. Default setting is AUTO.
Auto
This setting selects VARIABLE speed fan operation in standby based on the camera core temperature.
Manual
This setting allows you to set a fixed fan speed to be used during Record and Standby modes.
Record Speed
Sets a fixed fan speed to be used during Record. Range 25 – 100%. Default is 50%.
Standby Speed
Sets a fixed fan speed to be used during Standby. Range 25 – 100%. Default is 75%.
132
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
INDICATORS
Beep Speaker
Available options are OFF and RECORD/STOP. When RECORD/STOP is selected, an audible beep will be heard when record is started and another when record is stopped.
EVF Tally Light
When checked, enables the Record Tally Red LED on the front of the EVF.
MAINTENANCE
The maintenance menu allows the user to check system status and information, save the camera diagnostic LOG to attached media, perform a software update, calibrate the sensor, perform a camera self test, and reset system settings to factory defaults.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
133
SYSTEM INFO
When selected the Viewfinder output(s) will display the camera Model, current firmware Version, installed and camera P.I.N.
SAVE LOG
Select to write camera’s .LOG file to the REDMAG 1.8” SSD. The .LOG file is a diagnostic tool that can assist RED with camera troubleshooting. After capture, upload the .LOG file to the RED customer service team contactable at www.RED.com/support .
After successfully writing the log file to media, viewfinder output(s) will display LOG SAVE COMPLETED.
REDMOTE will also display this message.
If media is not attached to the camera when attempting to perform a write log request, external monitors will display NO MEDIA ATTACHED.
NOTE: Log files will be stored as *.txt files in the 1.8” SSD root directory.
SW UPDATE
NOTE: Firmware upgrade currently uses a force upgrade procedure as outlined in APPENDIX A:
UPGRADING CAMERA FIRMWARE.
134
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
CALIBRATION
Sensor calibration is a process where the camera generates a calibration map to correct for pixel defects and offsets based on current system and environmental settings. This allows you to perform a
Black Shading calibration of the MYSTERIUM X sensor two (2) different ways; Default (at 24 FPS @ 1/48
SEC) or using your current FPS/Exposure settings.
To calibrate the sensor the image needs to be as dark as possible:
• At a minimum put a lens cap on the lens (WARNING: Not all lens-caps completely block IR. They are made to protect the lens, not necessarily to block light...)
• Preferably, take of the lens, and use the lens-mount cap provided by RED.
• If possible, use a dark room.
• Just closing the Iris is NOT sufficient.
Additionally a SSD needs to be inserted in the camera to store the raw images during calibration.
Calibration is required:
• If the temperature deviates significantly from the currently used calibration, it is recommended to recalibrate the sensor.
• If very long exposure (~longer then 1/24 Sec) is used it is recommended to recalibrate.
After Calibration with a lens cap on and ISO set to maximum, the sensor should show a uniform noise profile over the whole area without any falloffs on any side. You can check at which temperature/exposure time the currently used calibration was taken on under SETTINGS >
MAINTENANCE > SYSTEM STATUS under Calibration.
Calibration maps will still be available after performing a system restore under SETTINGS >
MAINTENANCE > RESTORE SYSTEM; however the factory calibration map will be reselected.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
135
CURRENT CALMAP
Calibration maps are stored in the camera. Due to the nature of the camera, different calibration maps are needed for different situations.
Factory
This is the calibration map generated during production. This map is always present and selected as default on first use after performing a system restore under SETTINGS > MAINTENANCE > RESTORE
SYSTEM.
User HS
The user can select the CURRENT CALMAP. The dialog only shows the calibration maps stored in memory (FACTORY and USER HS in this case).
BLACK SHADING (DEFAULT)
This option uses fixed settings which are the same used for the factory calibration (around 23 Deg C).
BLACK SHADING (CURRENT FPS/EXPOSURE SETTINGS)
This option generates a calibration with the currently set frame rate/exposure. This can be used to generate a calibration for long exposures. After calibration (Which takes about 10 min), the new map is automatically selected.
136
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
BLACK SHADING PROCEDURE
The calibration procedures are the same for both BLACK SHADING options.
The calibration procedures are the same for both Black Shading (24 FPS @ 1/48 SEC) and Black
Shading (Current FPS/Exposure) options.
When selected, a screen will appear asking if you wish to proceed with Black Shading calibration.
REDMOTE will also display the following messages.
Black Shading calibration procedure:
1. Ensure the sensor is NOT exposed to the calibration light source by installing the lens cap properly.
2. Ensure a properly formatted SSD is attached to the camera and properly formatted.
3. Select OK to perform the Black Shading calibration. The calibration will make 2 passes.
4. A status screen will show progress of the Capturing step. Second pass shown.
5. Once Capturing is complete, a status screen will show progress of the Analyzing step.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
137
6. Once Analyzing is complete, a status screen will show progress of the Erasing step.
7. Once Erasing is complete, a status screen will show progress of the Programming step.
8. The camera will perform this procedure twice.
9. After Programming, CALIBRATION SUCCESSFUL will be displayed. Select OK to complete Black
Shading calibration.
SELF TEST
When selected allows you to perform a self-test for the sensor and LCD Touchscreen.
138
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ENABLE / DISABLE SENSOR TEST PATTERN
When selected enables / disables the sensor test pattern (White Screen). To turn on, select ENABLE
SENSOR TEST PATTERN.
To turn off, select DISABLE SENSOR TEST PATTERN.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
139
TOUCHSCREEN
When selected allows you to perform a touchscreen self-test.
When the touchscreen self-test is on, you can verify all areas of the touch screen respond to touch.
Simply touch each box using your finger. The touchscreen responds to the touch and the Green box turns Blue.
To exit the Touchscreen Self-Test:
• Place your finger on the touchscreen and hold it there until the main screen appears.
• Press the Enter or Menu button on the Side Handle or REDMOTE.
RESTORE SYSTEM
Restore System permits ALL camera configuration and setup data to be reset to factory default values.
140
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
When selected, you will be asked to confirm if you want to delete all settings and restore the factory default settings. After settings are restored, “DEFAULT SETTINGS RESTORED, INITIALIZING
RESTART…” Camera will automatically power down and will require you to manually power it up.
NOTE: User key settings will be reset as well as any other changes from the cameras default
settings. The REDMOTE will also require paring to communicate wirelessly with the camera.
REDISCOVER
Rediscovers all hardware and caches the data for future boot cycles.
When selected, you will be asked to confirm if you want to reset all hardware discovery settings. After settings are reset, “RESET HARDWARE DISCOVERY SUCCESSFUL, INITIALIZING RESTART…”
Camera will automatically power down and will require you to manually power it up.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
141
MOTION SENSOR CALIBRATION
The RED DSMC Camera displays data from the accelerometer to help orient the camera. After a firmware upgrade or Factory Restore the motion sensors need to be re-calibrated through the
Maintenance->Motion Calib menu."
142
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
PLAYBACK
Playback allows you to view clips on media currently attached to the camera. It also allows you to change the look of the playback clips be changing settings available when in playback mode.
NOTE: SCARLET-X™ menus shown, EPIC menus similar.
UPPER CONTROLS
From Left to Right are ISO, WHITE BALANCE, VIEW, PRESETS, MEDIA, SEETINGS, and META. Below the settings is the clip playback status bar.
Exit Playback ICON (Touchscreen)
Select the O on the Left to exit Playback mode.
NOTE: The Menu ICON on the Right does not respond to commands when in Playback mode.
ISO
Allows you to change the ISO in the clip during playback.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
143
WHITE BALANCE
Allows you to change the White Balance in the clip during playback.
Advanced Menu
Opens the advanced White Balance settings without the ability to Calculate.
VIEW
Allows you to select the items to be displayed in the playback window. Available options are Center, File
Name, Time Code, Frame Guide, Action Guide, and Title Guide.
144
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
PRESETS
Allows you to apply presets to the clip during playback.
MEDIA
When selected will list all available clips on the attached media.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
145
Touchscreen
1. Double-Tap the desired clip to open in the playback window.
2. Load will also highlight. You can also select LOAD to load the clip in the player and allow playback.
Side Handle / REDMOTE
1. Select the desired clip to playback and press the ENTER button.
2. Load will highlight. Select LOAD to load the clip in the player and allow playback.
146
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
SETTINGS
Available options are DISPLAY, LOOK and RECORD.
Display
Available options under Display are TOOLS and ZEBRA.
Tools
Allows you to toggle ON/OFF Exposure, Focus, Video, Edge, and RAW. Refer to SETTINGS MENU >
DISPLAY > TOOLS for complete details about these options.
Zebra
Allows you to toggle ON/OFF Zebras. Refer to SETTINGS MENU > DISPLAY > ZEBRA for complete details about these options.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
147
Look
Allows you to adjust the Color, Gain, FUT, and Curve of the image during playback. Refer to SETTTINGS
MENU > DISPLAY > LOOK for complete details about these options.
Record (Exit)
When selected will exit playback to the main menu.
META
Displays current clip META information.
148
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
CLIP PLAYBACK STATUS BAR
Displays the progress of the clip during playback.
Touchscreen
When using the touchscreen you can swipe your finger Left or Right to open and allow playback of the previous or next clip on the media.
Side Handle / REDMOTE
When using the Side Handle or REDMOTE you can use the navigation group to highlight the clip playback status bar.
The navigation group will also allow you to perform the following actions to the clip:
C
A
B
A Scroll Wheel B Directional Pad C Enter Button
• Scroll Wheel: Rotating Clockwise or Counter-Clockwise will move through the clip on frame at a time forwards or backwards.
• Directional Pad: Pressing Left or Right to open and allow playback of the previous or next clip on the media.
• ENTER Button: Pressing the ENTER button controls Play / Pause of playback.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
149
LOWER CONTROLS
From Left to Right, PLAYBACK SPEED, IN POINT MARKER, FRAME-BY-FRAME REVERSE,
PLAY/PAUSE, FRAME-BY-FRAME FORWARD, OUT POINT MARKER, PLAY ONCE/LOOP, and
PLAYBACK DIRECTION
RESOLUTION / PROJECT FRAMERATE / QUALITY
Display clip Resolution, Framerate and Quality (REDCODE). When using the touchscreen, touch the
Resolution, Framerate and Quality (REDCODE) to display the METADATA for the clip.
HISTOGRAM
Displays the clip histogram. The histogram will change based on any changes made in the Upper
Controls. When using the touchscreen, touch the histogram to display the TOOLS menu.
PLAYBACK SPEED
Allows you to select x1, x2, x4, x8, or x16 playback speed.
150
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
IN / OUT POINT MARKER
Allows you to set In and Out Points during clip playback. This allows you to playback only a certain portion of the clip as desired. Helps when the clip is rather long and you want to focus on a particular segment. The In (Red) and Out (Green) points will be displayed in the Clip Playback Status Bar. You can use the navigation group to select the exact location of the In and Out Points if desired.
FRAME-BY-FRAME REVERSE / FORWARD
Allows you to move through the clip frame-by-frame in the reverse direction.
PLAY / PAUSE
Allows you to play and pause the clip.
PLAY ONCE / LOOP
Allows you to choose to play the clip one time or to loop the clip in the player. Loop is shown below.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
151
PLAYBACK DIRECTION
Allows you to play the clip forward or backwards. Reverse playback is shown.
ADDITIONAL CLIP/CAMERA INFORMATION
Will indicate if clip was recorded in HDRx and current camera power status as well as audio input signals.
POWER
The power menu displays the current power status of all attached power sources as well as allows you to shutdown the camera.
POWER STATUS
The power status is displayed for the BRAIN, SIDE HANDLE, REAR 1, REAR 2, REAR 3, and REAR 4.
Below is what is displayed when the camera is connected to DC power and a REDVOLT is installed into the side handle with REDVOLT batteries installed in the optional QUAD BATTERY MODULE.
152
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
SHUTDOWN
Power OFF controls are interlocked to prevent accidental powering down of the camera. For details on the different ways to power down your RED DSMC Camera, refer to BASIC OPERATION > POWER
DOWN.
1. Enter the Secondary Menu using the touch screen, REDMOTE or Side Handle.
2. Select POWER.
3. Select SHUTDOWN.
4. The camera will immediately power down displaying SHUTTING DOWN…. If a REDMOTE is connected, the same message will display.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
153
APPENDIX A: UPGRADING CAMERA FIRMWARE
Your RED DSMC camera functionality may be upgraded by installing the latest firmware.
Camera firmware is identified by Version and SVN number, which will be displayed by the camera on the
LCD display when SYSTEM INFO is selected. A higher number reflects a later release.
Make a habit of frequently visiting www.RED.com/support to check for later versions of camera firmware, Operations Guide updates, and post-production software.
Your REDMOTE also requires a firmware upgrade. Go to APPENDIX E: REDMOTE OPERATION >
MAINTENANCE > UPGRADING REDMOTE FIRMWARE.
VERIFY CURRENT CAMERA FIRMWARE
With the camera ON, select SECONDARY MENUS > SETTINGS > MAINTENANCE > SYSTEM INFO.
The camera’s P.I.N. number and current firmware version will be displayed.
UPGRADE PROCEDURE
1. Download current firmware from http://www.RED.com/support .
2. Follow instructions in “Epic_read_me…” file.
3. To restore factory default settings, hold the power button down for 15 seconds while the camera is powering up.
154
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
APPENDIX B: MANAGING DIGITAL MEDIA
MEDIA
REDMAG 1.8” SSD is available with capacities of 64GB, 128GB or 256GB. Record duration is dependent on resolution, quality and frame rate, but a 64GB SSD will typically provide 24 minutes of
24fps 5K RAW recording.
On MAC computers with REDCINE-X PRO installed, RED Watchdog will mount the SSD as “READ-
ONLY” by default and you cannot write the firmware to the SSD. RED Watchdog is identified by the RED
Coin icon located on the Right side of the Menu Bar. Right-click on the icon to enter RED Watchdog settings and change to mount the drive as “READ-WRITE” to allow you to save the firmware to the SSD.
Refer to REDCINE-X PRO OPERATION GUIDE for complete RED Watchdog instructions and details.
IMPORTANT: After connecting REDMAG 1.8” SSD to the camera and BEFORE recording, you should format the media using the camera (even if formatting was previously performed on a computer). Go to ADANCED MENU > MEDIA > FORMAT to properly format media before recording.
FORMATTING MEDIA
Media must be formatted prior to using it for recording. Formatting is performed on camera, although media may be erased on a Macintosh OS X personal computer, allowing the camera to just add the necessary project profile and clip log data.
NOTE: Media formatted on-camera will use a name and root volume in the format:
Camera Letter + Reel Number + Month + Day + ** where ** is a two digit alphanumeric random number generated by the camera for each file e.g. A001_0512A6.RDM
Clips recorded to the media follow similar naming conventions
A001_C001_0512A6_001.RDC and A001_C001_0512A6_H.mov etc.
IMPORTANT: Media must always be un-mounted prior to removal or disconnection from the camera. This ensures power is removed from the digital media and any open data files are closed.
Failure to do so may result in lost data or corrupted files. Refer to REMOVE MEDIA FROM
CAMERA (UNMOUNT).
This procedure outlines the formatting of REDMAG 1.8” SSD media using the RED DSMC camera.
Formatting the SSD media will take about 10 seconds.
1. Insert SSD into camera.
-
Insert the REDMAG 1.8” SSD with the RED logo facing outward (away from camera body). SSD firmly into its slot, but without using excessive force to prevent damage.
2. When SSD media is inserted into the camera, the camera will recognize if the media is unformatted:
-
On LCD, EVF and external monitors, in the media section of the GUI, NONE will be displayed twice (as opposed to when no media is inserted, the GUI displays NONE with three dashes below “---“).
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
155
-
On REDMOTE, NONE will be displayed twice (as opposed to when no media is inserted, the GUI displays NONE with three dashes below “---“).
- On the Side Handle, NA will be displayed (same as if no media is present).
3. To format the media select SECONDARY MENUS > MEDIA > FORMAT MEDIA.
4. You will be prompted to set the media and select FORMAT.
-
Viewfinder output(s) will display “FORMATTING”.
NOTE: If when selecting FORMAT, the display indicates FORMAT FAILED, refer to MEDIA
5. Once formatting is completed, the Viewfinder output(s) will display “THE MAGAZINE WAS
SUCCESSFULLY FORMATTED THE DIGTAL MAGAZINE IS READY FOR IMMEDIATE USE”.
156
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
MEDIA CAPACITY REMAINING STATUS
The Viewfinder output(s) will display the remaining media capacity in the MEDIA indicator (100% is shown).
At 10%, remaining capacity the media status will turn yellow, at 5% it will turn red. At 2%, remaining the camera will cease recording. This reserves a small amount of capacity for ancillary data to be written to the media.
NOTE: When media is full, the Side SSD LED will flash Red.
EJECT MEDIA FROM CAMERA (UNMOUNT)
IMPORTANT: Media must always be Ejected (un-mounted) prior to removal or disconnection from the camera. This ensures power is removed from the digital media and any open data files are closed. Failure to do so may result in lost data or corrupted files.
Removing an SSD without first un-mounting it will not physically damage the media, however it does increase the risk of file corruption, so it’s good operational practice to un-mount the media if possible before removing or disconnecting.
IMPORTANT: Unmounting the digital media takes a few seconds, protects the integrity of your recorded data and helps clips mount instantly to your workstation once in post-production, so it’s a recommended habit to develop. If you do not un-mount the media the camera will offer a warning – your files may not be damaged, but you will have been warned!
NOTE: The camera will respond to physical removal of the media without un-mounting and display ”MEDIA REMOVED PRIOR TO UNMOUNT – DATA INTEGRITY RISK”.
USING REDMOTE / TOUCHSCREEN LCD
1. Go to SECONDARY MENUS > MEDIA.
2. Select EJECT MEDIA.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
157
3. When media is ejected, Viewfinder output(s) will display “MEDIA EJECTED SUCCESSFULLY“.
4. Media can now be removed from the camera.
USING SIDE HANDLE
1. By default, the lower of the three (3) SYSTEM KEYS is set to Eject Media when pressed.
2. When media is ejected, Viewfinder output(s) will display “MEDIA EJECTED SUCCESSFULLY“.
3. Media can now be removed from the camera.
USING SIDE SSD
1. Press both User Keys 1 and 2 at the same time to eject REDMAG 1.8” SSD Media.
2. When media is ejected, Viewfinder output(s) will display “MEDIA EJECTED SUCCESSFULLY“.
3. Media can now be removed from the camera.
COPYING MEDIA
For use when media is connected directly to your computer. When copying media, it is recommended that you drag the complete .RDM folder on the digital magazine to the archive storage media. This copies all the media and metadata files. You will not need to copy the log, magazine profile, or presets files, but if you do so, it will do no harm.
158
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ERASING MEDIA
NOTE: If the media was formatted using SECURE FORMAT, you cannot erase the media using an external source. Erasing of the media must be performed by formatting on the camera.
MACINTOSH OS X
1. Connect the REDMAG 1.8” SSD via RED STATION REDMAG 1.8".
2. Open the Disk Utility.
3. Carefully choose the drive from the list on the left.
4. Select the Erase tab.
5. Choose MS-DOS (FAT) as the Volume Format. You can add a Name if desired, however the camera will overwrite this.
IMPORTANT: Before performing the next step, double-check that this is the correct SSD that you wish to erase DATA FROM.
6. Select Erase. When the pop up window appears click on the Erase button.
7. When the media is erased, drag its icon to the trashcan and physically disconnect it.
8. The media will need to be formatting by the camera before use. Refer to FORMATTING MEDIA.
WINDOWS
1. Connect the REDMAG 1.8” SSD via RED STATION REDMAG 1.8".
2. Open Windows Explorer (go to my computer icon, right click and select EXPLORE).
3. Double-click on the drive you wish to erase files from.
4. Select all the files on the drive you wish to erase.
IMPORTANT: Before performing the next step, double-check that this is the correct SSD that you wish to erase DATA FROM.
5. Press the “DELETE” key on the keyboard, select FILE > DELETE or right-click on selected file and choose DELETE. When the pop up window appears click YES.
6. The media will need to be formatting by the camera before use. Refer to FORMATTING MEDIA.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
159
APPENDIX C: INPUT / OUTPUT CONNECTORS
CAMERA BRAIN FRONT
160
A
B
A MIC-1 3.5mm Audio Jack B MIC-2 3.5mm Audio Jack
Camera Brain Connectors - Front
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
MIC-1, MIC-2 (MICROPHONE AUDIO)
Two 3.5mm phone jacks on the front of the brain support two independent channels of balanced or unbalanced microphone level analog audio inputs.
A
C B
Microphone Input Connector
PIN
A (TIP)
B (RING)
C (SLEEVE)
SIGNAL
IN +
IN -
GND
DESCRIPTION
Mic Input (+48V Phantom Power)
Mic Input (+48V Phantom Power)
Camera ground
DIRECTION
In
In
--
Microphone Level analog audio input signals are routed via a high quality pre-amplifier and soft limiter, whose Gain may be controlled using the Input Level control to achieve the desired audio reference / recording level. Microphone inputs support +48V @ 10mA Phantom Power as a user selectable option. If
To assist with reference level setup, the camera provides a color-coded Peak Level Meter in the
Graphical User Interface, with witness marks that indicate 0dBu (-20dbFS) and 0Vu (- 16dBFS) levels.
Peak Level Meter range is –36dBu to +20dBu (-54dBFS to 0dBFS) and provides input clip indication.
NOTE: A pre-fabricated XLR to TRS interface cable, Part Number 790-0229, is available from RED
Digital Cinema .
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
161
CAMERA BRAIN REAR
162
C
G
D
E
A
B
A
B
C
D
E
F
G
HD-SDI
Headphone
SYNC (Video Sync)
CTRL (RS232 Control)
GIG-E (Ethernet)
DC IN (Power Input)
HDMI
Camera Brain Connectors - Rear
F
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
HD-SDI
A standard 75 Ohm BNC connector provides a broadcast specification high definition video output.
PIN
Center
Shield/Screen
SIGNAL
HD-SDI
GROUND
DESCRIPTION
SMPTE-292M HD-SDI
Camera ground
DIRECTION
Out
--
HD-SDI Output
The HD-SDI output provides a 720p progressive scan video feed operating at 50.00 or 59.94 Hz or a
1080p 10-bit 4:2:2 progressive scan video feed operating at 23.98, 24.00, 25.00 or 29.97 Hz when in
1.5GHz HD-SDI mode, or a 1080p 10-bit 4:2:2 progressive scan video feed operating at a 50.00 or 59.94
Hz when in 3GHz HD-SDI mode.
The HD-SDI output may be specified as a PROGRAM output (clean feed video) or as a PREVIEW output
(includes SurroundView™ look around, Clip Name, Timecode and Safe Action / Safe Title frame guides).
In addition to video, the HD-SDI output also provides two channels of embedded audio, Time of Day and Edge timecode, record Tally flag and Clip Name information as SMPTE RP-188 VITC2 HANC metadata.
NOTE: Default setting is PROGRAM.
NOTE: HD-SDI video output is Progressive Scan; it does not support 1080i or 1080PsF modes.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
163
HEADPHONE
A 3.5mm stereo jack provides two channels of adjustable level analog audio for monitor headphones.
A
C B
Headphone Output Connector
PIN
A (TIP)
B (RING)
C (SLEEVE)
SIGNAL
LEFT
RIGHT
GND
DESCRIPTION
Left channel audio
Right channel audio
Camera ground
DIRECTION
Out
Out
--
The camera’s four audio channels may be monitored in pairs: either 1L - 2R or 3L - 4 R or as a quad mix of 1+3L – 2+4R based on the MIX parameter. Default is 1L-2R.
Output volume may be adjusted as follows.
Volume: (master volume) Adjusts headphone volume equally for left and right outputs.
Range is -18dB to 0dB in 1dB steps. Default is -9dB.
NOTE: for maximum output signal quality, only use high impedance headphones.
NOTE: in Version 3.x software the above selection is not available, the output is set to 1L / 2R.
SYNC (VIDEO SYNC)
A 4-pin LEMO connector supports shutter synchronization, GPI, timecode and genlock input signals.
The shutter Sync input signal acts as an immediate response hardware trigger to commence a scan.
This is useful for motion control and other applications where the camera is driven by a master timing device. When using SYNC as the camera shutter timing reference, fine shutter start time timing
(SHUTTER PHASE) is disabled; make any desired timing adjustments at the external SYNC generator.
Alternatively, this input may be used as a GPI (General Purpose Input) trigger, whose function is programmed in the USER KEYS menu. Default function for the GPI trigger is Record Start / Stop.
The SMPTE timecode input provides a frame accurate time stamp for each frame of recorded video.
External TC must be chosen in the Project > Timecode menu. When SMPTE timecode is detected it will align the internal TC value to the external TC signal at every :00 frame crossing of the external TC signal.
164
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
The Video Genlock input may be used as a vertical interval reference signal for the sensor and HD-SDI outputs when precise synchronization is required between cameras, such as for 3D and live broadcasts.
Note: When GENLOCK is selected as the sensor shutter reference, shutter start timing (SHUTTER
PHASE) may still be adjusted. HD-SDI monitor outputs will automatically sync to the external
GENLOCK signal as soon as it is detected, there is no need to enable this function. Sensor shutter sync to GENLOCK is only supported with HD-SDI.
View into camera SYNC (Video Sync) Interface connector
Mating Connector: FGG.00.304.CLAD27Z
PIN
1
2
3
4
SIGNAL
GROUND
SS/GPI
TIMECODE
GENLOCK
DESCRIPTION
Common Ground
Shutter Sync / GPI Trigger Input
SMPTE unbalanced timecode Input
RS170A Tri-Level Sync Input
NOTE: The Camera Brain’s Shutter Sync / GPI Trigger uses a 3.3 V Schmitt trigger (5 V tolerant), current supplied by the trigger source. Both edges of the input signal may be used as a trigger.
For example, when GPI trigger is used for Record Start / Stop.
• Start Record: On Ground to 3.3 V transition
• During Record: Hold at 3.3 V
• Stop Record:
• During Stop:
On 3.3 V to Ground transition
Hold at Ground
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
165
NOTE: A pre-fabricated SYNC interface cable is available from RED Digital Cinema.
• P/N 790-0154 – Video Sync – Camera to 3 BNC – 3 ft. (1m)
• White BNC: Shutter Sync / GPI
• Yellow BNC: SMPTE Timecode
• Green BNC: RS170A Genlock
166
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
CTRL (RS232 CONTROL)
A 4-pin LEMO connector supports RS232 remote control for 3D camera communication, and third party metadata ingest applications.
The shutter Sync Output signal acts as an immediate response hardware tally of a scan. This is useful for 3D or motion control applications where a slave camera or lighting device needs to be synchronized to a master camera.
Alternatively, this output pin may be used as a GPO (General Purpose Output) tally, whose function is programmed in the USER KEYS menu. Default function for the General Purpose Output is Record Tally.
PIN
1
2
3
4
View into camera CTRL (RS232 Control) Interface connector
Mating Connector: LEMO FGG.00.304.CLAD27Z
SIGNAL
GROUND
232 RX
SS/GPO
232 TX
DESCRIPTION
Common Ground
RS232 RX
Shutter Sync / GPO Output
RS232 TX
NOTE: When active, the GPO tally presents 3.3V @ 0.04 Amps maximum between pins 1 and 3.
When used as Sync Out, the rising edge of the pulse indicates start of exposure. When used as a
Tally, the rising edge of the pulse indicates start of record, falling edge represents end of record.
NOTE: A pre-fabricated CTRL interface cable is available from RED Digital Cinema.
• P/N 790-0152 – RS232 – Camera to DB-9 – 3 ft. (1m)
• DB-9 Pin 1: Shutter Sync / GPO
• DB-9 Pin 2: RS232 Tx
• DB-9 Pin 3: RS232 Rx
• DB-9 Pin 4: Ground
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
167
GIG-E (ETHERNET)
A 9-pin LEMO connector provides a Gigabit Ethernet port for remote camera setup, master / slave camera communication and external metadata ingest.
View into Ethernet Interface connector
Mating connector: FGG.0B.309.CLAD32Z
PIN
1
2
3
4
7
8
5
6
9
SIGNAL
B1_DC +
B1_DC -
B1_DD+
B1_DD -
B1_DA-
B1_DA+
B1_DB+
B1_DB-
-
DESCRIPTION
Data Pair C+
Data Pair C-
Data Pair D+
Data Pair D-
Data Pair A-
Data Pair A+
Data Pair B+
Data Pair B-
Do Not Connect
DIRECTION
--
--
--
--
--
--
--
--
--
NOTE: Two pre-fabricated Ethernet interface cables are available from RED Digital Cinema.
• P/N 790-0163 – Ethernet – Camera to Camera – 3 ft. (1m)
• P/N 790-0159 – Ethernet – Camera to RJ45 – 3 ft. (1m)
168
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
DC IN (POWER INPUT)
The 6-pin LEMO connector accepts DC input power between +11.5 V and +17 V DC. Power conditioning provides protection against reverse-polarity connection, ESD, under and over voltage, and over current.
View into camera DC IN Power Input connector
Mating Connector: LEMO FGJ.1B.306.CWLD72Z
PIN
1
2
3
4
5
6
SIGNAL
+VBATT
SCL-BATT
GROUND
SCA-BATT
DESCRIPTION
Power input, +11.5 to +17 V DC
Serial Battery Bus Clock
Power Return (Camera Ground)
Serial Battery Bus Data
WARNING: It is very important that both pairs of +VBATT and GROUND pins are wired up. DO
NOT fabricate power cables with just one each of +VBATT and GROUND pins wired, as this may cause damage to the camera’s power supply; this is not covered by Warranty.
NOTE: Two pre-fabricated DC Power input cables are available from RED Digital Cinema.
• P/N 790-0138 – DC Power – REDBRICK ® QUICKPLATE to Camera – 18 in. (0.5m)
• P/N 790-0164 – DC Power – XLR to Camera – 10 ft. (3m)
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
169
HDMI OUT
The HDMI output supports an HDTV and PC monitor compatible 10-bit 4:2:2 progressive scan video signal (with embedded audio) at 720p and 1080p resolution.
The HDMI output may be specified as a PROGRAM output (clean feed video) or as a PREVIEW output
(including SurroundView™ look around, Clip Name, Timecode and Safe Action / Safe Title frame guides).
In addition to video data, the HDMI output also provides 4 channels of embedded audio.
NOTE: Default setting is PREVIEW.
NOTE: HDMI video output is Progressive Scan; it does not support 1080i or 1080PsF modes.
170
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
SIDE SSD MODULE
REAR
A
B
FRONT
A SSD Slot
B VIEWFINDER (LCD/EVF)
Side SSD Module
The Side SSD Module mounts to the left side of the camera Brain. On the rear face of this module is a slot for inserting a REDMAG 1.8”SSD digital Magazine. Do not attempt to insert any other media type, or any foreign objects into this slot, as damage to the Side SSD Module and / or the camera Brain may occur.
The VIEWFINDER output Module on the front face of the Side SSD Module provides digital video, communications and power interconnection between the camera and a RED EVF or RED LCD digital display. Due to the requirement for absolute data integrity this requires a custom cable manufactured by
RED, the pin-out of this interface is not published.
NOTE: Pre-fabricated EVF / LCD cables are available from RED Digital Cinema.
• P/N 790-0157 – EVF / LCD Cable – Right Angle to Right Angle – 6 in. (0.15m)
• P/N 790-0153 – EVF / LCD Cable – Right Angle to Straight – 18 in. (0.5m)
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
171
REDMOTE
This section describes the physical connectors on the REDMOTE.
B
A
A Mini USB B Camera Interface
REDMOTE Connections
The REDMOTE interface connector allows communication between the REDMOTE and the camera
Brain or any expansion module. Make sure these contacts are kept clean and free of any contaminants that may interfere with a reliable electrical contact.
172
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
KEY
Record Half Press
Record Full Press
KEY
User A Press
User B Press
User C Press
User D Press
User 1 Press
User 2 Press
User 3 Press
User 4 Press
User 5 Press
User 6 Press
User 7 Press
User 1+4 Press
Still Select
Movie Select
Record Half Press
Record Full Press
Backlight Press
Nav Menu Press
Nav North Press
Nav South Press
Nav West Press
Nav East Press
Nav Enter Press
Rocker + Press
Rocker - Press
User A Release
APPENDIX D: DEFAULT KEY FUNCTIONS
CAMERA BRAIN
FUNCTION KEY
Key Disabled-
Record: Toggle
Record Half Release
SIDE HANDLE
KEY FUNCTION
AF Mode: Cycle
WB: Auto Calc
Magnify: Toggle
Exposure Check: Toggle
Slot: Set ISO
Slot: Set Aperture
Slot: Set Shutter
Slot: Set Color Temp
Exposure Check: Toggle
-Key Disabled-
User B Release
User C Release
User D Release
User 1 Release
User 2 Release
User 3 Release
User 4 Release
User 5 Release
User 6 Release
User 7 Release
User 1+4 Release Eject Media
SH: Toggle Key Lock
Focus Mode: Still
Focus Mode: Motion
AF: Start
Record: Toggle
SH: Toggle Backlight
Navigation: Menu
Navigation: Up
Navigation: Down
Navigation: Right
Navigation: Left
Record Half Release
Record Full Release
Backlight Release
Nav Menu Release
Nav North Release
Nav South Release
Nav East Release
Nav West Release
Nav Enter Release
Rocker + Release
Rocker - Release
Rotary Front CW Navigation: Select
Iris: Open
Iris: Close
-Key Disabled-
Rotary Jog CW
Rotary Front CCW
Rotary Jog CCW
FUNCTION
-Key Disabled-
FUNCTION
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
Navigation: CW
Navigation: CW
Navigation: CCW
Navigation: CCW
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
173
KEY
User 1 Press
User 2 Press
User 1+2 Press
Record Half Press
Record Full Press
KEY
User A Press
User B Press
User C Press
User D Press
Still Select
Movie Select
Record Half Press
Record Full Press
Nav Menu Press
Nav North Press
Nav South Press
Nav East Press
Nav West Press
KEY
LCD User 1 Press
LCD User 2 Press
LCD Up Arrow Press
SIDE SSD MODULE
FUNCTION KEY
-Key Disabled-
-Key Disabled-
User 1 Release
User 2 Release
Record Half Release Eject Media
AF: Start
Record: Toggle
Record Full Release
REDMOTE
FUNCTION
AF Mode: Cycle
RAW Check: Toggle
Magnify: Toggle
Exposure Check: Toggle
Focus Mode: Still
Focus Mode: Motion
AF: Start
KEY
Nav Enter Press
Rocker + Press
Rocker - Press
Rotary CW
Rotary CCW
User A Release
User B Release
Record: Toggle
Navigation: Menu
Navigation: Up
Navigation: Down
User C Release
User D Release
Record Half Release
Record Full Release
Navigation: Right Rocker + Release
Navigation: Left Rocker - Release
DISPLAY (BRAIN)
FUNCTION
Magnify: Toggle
Exposure Check: Toggle
Incr. LCD Brightness
KEY
LCD Down Arrow Press
EVF User 1 Press
EVF User 2 Press
FUNCTION
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
FUNCTION
Navigation: Select
Iris: Open
Iris: Close
Navigation: CW
Navigation: CCW
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
-Key Disabled-
FUNCTION
Decr. LCD Brightness
Magnify: Toggle
Exposure Check: Toggle
174
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
APPENDIX E: REDMOTE OPERATION
CONTROL, CONNECTORS AND DISPLAY
This section describes the REDMOTE physical controls, connectors and color LCD display.
CONTROLS
C
D
A L
K
E
I
H
B M
F
N
G
J
A
B
C
D
E
Stills/Motion Switch
Release Latch - Left
Record Status LED
Wireless Status LED
Zoom Rocker Switch
F
G
H
I
J
REDMOTE Controls
User Function Keys A-D
MENU Button
Menu Buttons 1-3
Navigation Group
Focus / Record Button
K
L
M
N
Menu Buttons 4-8
Power/Lock Switch
Release Latch – Right
USB External Power Port
STILL / MOTION SWITCH
The STILLS/MOTION toggle switch is used to switch between STILLS operation (DOWN) and MOTION operation (UP). When the toggle switch is set to the MOTION position, all camera settings and defaults are movie specific. When the toggle switch is set to the STILLS position, all camera settings and defaults are stills photography specific.
Note: In Version 3.x software the STILLS/MOTION switch is disabled. Default mode is MOTION.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
175
LEDS
There are two status LED indicators located above the rockers switch on the left side of the LCD display.
The upper LED is used to signal camera readiness and camera record status.
• Red – Camera Startup / Camera Recording.
The lower LED is used to signal camera readiness and REDMOTE communication status to the camera.
• Green – Camera Ready / REDMOTE connected.
• Blinking Green – Searching / Establishing communication
ROCKER SWITCH
The function of the pressure sensitive ROCKER SWITCH may be assigned by the operator to one of a number of operational controls. Refer to SECONDARY MENUS > SETTINGS > SETUP > KEYS /
SHORTCUTS.
USER FUNCTION KEYS
The function of each User Function Key may be assigned by the operator to one of a number of operational controls. Refer to SECONDARY MENUS > SETTINGS > SETUP > KEYS / SHORTCUTS.
Default settings for User Function Keys A-D are as follows:
• User Key A – Toggles Auto Focus
• User Key B – Toggles View RAW
• User Key C – Toggles Focus Check (1:1 Magnify)
• User Key D – Toggles Sensor RAW Exposure Check
MENU BUTTON
Below and to the left of the User Keys is the MENU button, press to switch between primary level and secondary level Camera menus. When in Camera menus or REDMOTE menus, press once to exit menus.
SOFT MENU BUTTONS 1-3
Below the LCD are three Soft Menu Buttons, whose specific functions are indicated by the LCD screen.
For complete information refer to OPERATION > REDMOTE MENUS > SOFT MENU BUTTONS 1-3.
NAVIGATION GROUP
The Navigation Group allows navigation of the camera menus and adjustment of selected parameters.
176
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
C
A
B
REDMOTE Navigation Group
A Scroll Wheel B Direction Keys
The Navigation Group has three separate operational capabilities.
C Enter Button
SCROLL WHEEL
The Scroll Wheel allows the operator to select and adjust the values of selected camera parameters.
DIRECTION KEYS
The Direction Keys allows Left / Right / Up / Down navigation thru the camera menus to select a desired parameter for adjustment.
ENTER BUTTON
The Enter button allows confirmation of a parameter adjustment or operational mode selection.
FOCUS AND RECORD BUTTON
Below the Navigation Group is the focus and record button. A half press initiates Auto Focus; a full press initiates Stills capture or starts /stops a Movie recording.
When recording, the upper LED will illuminate Red and the Timecode readout on the REDMOTE LCD will also display in red colored text.
Note: In Version 3.x software the frame count of the Timecode is not displayed. This is normal and does not indicate an error.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
177
SOFT MENU BUTTONS 4-8
To the right of the LCD are five Soft Menu Buttons. These buttons select a variety of camera status pages. For complete information refer to OPERATION > REDMOTE MENUS > SOFT MENU BUTTONS
4-8.
Note: In Version 3.x software, Soft Menu Buttons 7 and 8 are undefined.
POWER / KEY LOCK SWITCH
If the REDMOTE is powered OFF, moving and holding the switch in the down (POWER) direction for 2 seconds will power UP the REDMOTE and if the REDMOTE is powered ON, moving and holding the switch in the down (POWER) direction for 5 seconds will power DOWN the REDMOTE.
Moving the switch to the up (LOCK) position will lockout all REDMOTE buttons to prevent unintentional operation. When in the LOCK position, KEYS LOCKED will be displayed in red text above the SOFT
MENU BUTTONS 1-3 on the REDMOTE LCD display.
USB POWER PORT
The USB port may be used to charge the REDMOTE internal battery from a suitable USB power source.
Refer to CHARGING / BATTERY LIFE > CHARGING USING USB CONNECTOR for complete information.
OPERATION
DOCKING AND UNDOCKING
This section describes how to physically dock / undock the REDMOTE to / from the camera Brain or the back of the rearmost expansion module.
DOCKING
1. Place the female V-Mount of the REDMOTE over the male V-Mount of the camera Brian or rearmost module.
178
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Note: For illustration only: rear surface of REDMOTE should face towards camera
2. Slide the REDMOTE down until a click is heard which indicates the REDMOTE is securely attached.
UNDOCKING
1. Depress the two latch release buttons located on each side of the REDMOTE.
2. Slide the REDMOTE upward to release from the V-Mount of the camera Brain / rear most module.
3. Remove the REDMOTE.
POWER UP / DOWN
Located on the upper right side of the REDMOTE is the Power / Key Lock Switch (refer to CONTROLS).
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
179
POWER UP
CONNECTED TO CAMERA
If the REDMOTE is physically attached to a camera, when the camera is powered up the REDMOTE will automatically power up along with the camera.
NOT CONNECTED TO CAMERA
To manually power up the REDMOTE, slide and hold the Power / Key Lock Switch in the down direction for 2 seconds, then release.
POWER DOWN
USING CAMERA
When REDMOTE is connected to the camera and the camera is powered down, the REDMOTE will also power down. When disconnected from the camera, the REDMOTE will not power down with the camera.
USING REDMOTE
To power down REDMOTE, slide and hold the Power / Key Lock Switch in the down direction for 5 seconds.
Or slide and hold the Power / Key Lock Switch in the down direction momentarily, then release. A screen will display with options to power down the REDMOTE, the Camera, or REDMOTE and Camera together. Select the desired option and press the ENTER key in the REDMOTE Navigation Group.
NOTE: Wireless mode shown. When docked to camera, SHUTDOWN CAMERA is not displayed.
180
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
RECORDING
• To record, press the Red REC (record) button. If media is connected and properly formatted, the upper LED will illuminate Red and the Timecode value displayed in the LCD will change to Red text.
To stop recording, press the REC button a second time. After recording to media is completed, the upper LED will go out and the Timecode value displayed in the LCD will change back to White text.
Note: If media is NOT connected when record is requested, the REDMOTE LCD and camera
VIEWFINDER (MENUS) output will indicate “NO MEDIA ATTACHED”.
ACCESSING CAMERA CONTROLS / SETTINGS
The Navigation Group is used to navigate through camera menus. Refer to CAMERA OPERATIONAL
CONTROLS > REDMOTE > NAVIGATION GROUP. The camera settings and status are displayed on the
REDMOTE LCD. Refer to BASIC OPERATION > GRAPHICAL USER INTERFACE AND NAVIGATION >
REDMOTE.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
181
182
CHANGING CAMERA SETTINGS
USING CAMERA LCD / EXTERNAL MONITOR AS REFERENCE
To adjust a parameter value displayed on the camera’s Upper Status Group, first note the red colored bar (located under 24fps in this example), indicating the currently active parameter for instant adjustment.
Use the NAVIGATION GROUP directional pad to move the cursor to a different parameter if desired, then press the ENTER key to select that parameter and use the Scroll Wheel to adjust that parameter’s value. To confirm the change in parameter value and to exit the adjustment menu, press the ENTER button.
To access the camera’s menus, press the MENU button at the lower left. The MENU displays on the
EVF, LCD or external monitors if the LCD and/or EVF are not connected disconnected.
Use the NAV GROUP to make changes to the cameras settings. Use the scroll wheel and directional pad to move the cursor to navigate and make changes to the desired settings. When a desired setting change is made, press the ENTER button or the directional pad UP arrow to exit from that setting.
Exiting Menus to Main Screen
To EXIT from the Secondary Menus and return to the main screen:
• Press the MENU button until the main screen is displayed.
USING REDMOTE LCD STAND-ALONE
The LOCAL function of the REDMOTE allows you to adjust the camera settings from the REDMOTE while observing the parameters directly on the REDMOTE LCD as opposed to on the camera LCD or an external monitor. For complete details refer to REDMOTE MENUS > SOFT MENU BUTTONS 1-3 > 2
REMOTE > LOCAL.
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ADVANCED OPERATION: REDMOTE MENUS
SOFT MENU BUTTONS 1-3
Located below the main LCD display are three Soft Menu Buttons, who access advanced function menus identified by text in the LCD directly above the corresponding button. These menus control wireless connection (CONNECT), camera or local menus (REMOTE/LOCAL) and system setup (SETUP).
WIRELESS CONNECT: SOFT MENU BUTTON 1
Note: This Button is hidden if REDMOTE is attached to the camera or rear-most camera module.
Note: If a REDMOTE has previously been successfully paired with a camera, and the REDMOTE has scanned the wireless network and found that camera, the following operation can be bypassed as the REDMOTE will auto scan and connect to that camera each time it is powered ON and undocked.
CONNECT REDMOTE TO A PAIRED CAMERA
NOTE: The following procedure assumes the camera has already been paired and named
DEFAULT under the camera’s SETTINGS > SETUP >REDMOTE and COMMUNICATION menus.
1. Press CONNECT to initiate a scan by the REDMOTE for available paired cameras in wireless range.
2. If the REDMOTE fails to find a camera it has been paired with the following screen will be displayed.
Select RESCAN and press the ENTER button in the Navigation Group to force a second scan for paired cameras in wireless range. A wireless scan typically takes 20-30 seconds.
3. When REDMOTE finds a camera or cameras it has been paired with in wireless range, the name of the available camera or cameras will be displayed - for example a single camera named DEFAULT.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
183
4. Select the desired camera to connect to for REDMOTE wireless operation and press the ENTER button in the Navigation Group. The REDMOTE will connect to the selected camera.
5. Once connected, the REDMOTE will display the key operating parameters of the selected camera.
The wireless signal strength will be shown in the lower Right corner of the REDMOTE screen.
The camera VIEWFINDER monitor output will confirm REDMOTE is wireless connection by displaying
RM and a signal strength icon in Green on the Lower Status Group.
184
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Note: Once this procedure has occurred once, the REDMOTE will automatically search for the camera each time it is undocked, until the paired camera selection is changed.
CANCEL
If you wish to exit the CONNECT menu at any time press CANCEL.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
185
DISCONNECT
To stop communicating wirelessly with the camera, select Soft Menu Button 1 Connect, then select
DISCONNECT and press the ENTER key in the Navigation Group.
RECONNECTING IF SIGNAL IS LOST
On loss of wireless communication REDMOTE will scan for the camera it was last paired with.
If the REDMOTE is unable to re-connect after 30 seconds, it will enter the manual SCAN menu, follow the procedure outlined about to scan and identify camera(s) that you wish to connect to.
186
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
OPERATING WITH MULTIPLE CAMERAS FROM A REDMOTE
To control more than one camera from a single REDMOTE, first pair the REDMOTE with each camera.
After pairing REDMOTE to the desired cameras, press Soft Menu Button 1: CONNECT. Available cameras will be listed.
Select the camera you wish to control and press the ENTER button. When you want to switch to a different camera, press Soft Menu Button 1: CONNECT again to list available cameras and re-select.
REDMOTE OR LOCAL MENUS: SOFT MENU BUTTON 2
When selected allows the user to toggle the REDMOTE between REMOTE and LOCAL menus.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
187
REMOTE
Allows the user to adjust camera settings from REDMOTE, by navigating the camera menus appearing on the VIEWFINDER output of the camera, with summary data only appearing on the REDMOTE LCD
LOCAL
Allows the user to adjust camera settings from REDMOTE, by navigating camera menus appearing on the REDMOTE LCD, with summary data only appearing on the VIEWFINDER output of the camera.
CUSTOMIZING LOCAL MENUS.
When operating in LOCAL mode, REDMOTE provides the user the option to configure which parameters to display in each of the parameter status windows. You can assign the parameters to one of the 5 pages of information available under Soft Menu Buttons 4-8.
To customize parameters:
1. Ensure camera is ON and wirelessly connected to REDMOTE.
2. If Soft Menu Button 2 reports as REMOTE, press it once so it reports LOCAL.
3. Select the Soft Menu Button page you would like to set the parameter on from the right hand side of the LCD. Refer to SOFT MENU BUTTONS 4-8.
4. Use the directional arrows on the Navigational Control to move the Red cursor to the desired location within that page to place the parameter.
5. Now press SETUP: Soft Menu Button 3.
188
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
6. Select “Setup Slot” and press the ENTER button.
7. A new Setup window will appear displaying available parameters to display.
8. Select the desired parameter and press the ENTER button.
9. You may now control this parameter directly from the REDMOTE.
REDMOTE SETUP: SOFT MENU BUTTON 3
When pressed, SETUP provides the option of forcing the REDLINK wireless link ON or OFF and selecting the following REDMOTE Setup menu.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
189
Adjustable parameters include LCD screen brightness; beep speaker Volume and Auto Shutdown time.
In the lower section of the display is the MAC address and the current firmware build of the REDMOTE
Brightness
The BRIGHTNESS control adjusts the LCD backlight intensity. Set value to maximum for daylight visibility, set value lower for nighttime operation or for maximum battery run time when operating in wireless mode.
Default value is Maximum.
Volume
The VOLUME control adjusts the loudness of the beep speaker. As you adjust this value the REDMOTE will beep the speaker to give an audible confirmation of the selected volume. Default value is Minimum.
Auto Shutdown
The AUTO SHUTDOWN control adjusts the amount of time a REDMOTE will continue to operate when in the wireless mode after no detected activity (i.e. no button presses are detected) before powering down.
Default value is OFF (REDMOTE will operate continuously until manually powered down.)
DISPLAY LAYOUT: SOFT MENU BUTTONS 4-8
To the right of the LCD are five Soft Menu buttons 4-8. These buttons select between a variety of camera status page layouts.
Note: In Version 3.x software, buttons 7 and 8 are undefined.
190
Menu Button 4 Menu Button 5 Menu Button 6 Menu Button 7 & 8
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
MAINTENANCE
INTERNAL BATTERY
CHARGE STATUS
An icon shows the charge status of the REDMOTE battery in the lower right corner of the LCD.
When REDMOTE is operating in wireless mode, the icon indicates current charge capacity. When satisfactory the icon is displayed in Green. When battery charge becomes marginal, the icon turns
Yellow. When battery charge is critically low, and wireless communication is at risk of being lost the icon turns Red. The REDMOTE should be re-attached to the camera or rearmost module, or be attached to a suitable USB power source, to recharge the battery before re-attempting wireless operation.
When attached to the camera or rearmost camera module, or external USB power source, this icon will either display solid green, indicating fully charged, or blink, indicating the battery is being charged by the camera or external USB power source.
BATTERY LIFE
When using the REDMOTE in wireless configuration, the battery will last approximately 8 hours before charging is necessary.
NOTE: When not using the REDMOTE, for maximum battery storage life, use the Power / Lock
Switch to power down the REDMOTE completely by pressing down in the power off position and using the displayed menu to shut down the REDMOTE and/or the REDMOTE and camera. Refer to POWER UP / DOWN > POWER DOWN. If the Power / Lock Switch is pressed down in the power off position and held until the REDMOTE powers down, the battery storage life will be reduced greatly as there will be a slight power draw on the REDMOTE when shut down using this procedure.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
191
CHARGING
CHARGE TIME
A fully discharged REDMOTE battery will be fully charged in approximately 6 hours.
USING CAMERA
While connected to the camera, the REDMOTE will automatically recharge its internal battery. Charge status is indicated by the Green Battery Icon at the top-right of the REDMOTE LCD display screen. A fully discharged REDMOTE battery will be re-charged in approximately 6 hours if connected to a powered camera or a USB based power source such as laptop P.C.
USING USB CONNECTOR
The REDMOTE can be charged by connecting the RED Mini-USB-to-USB cable (790-0230) between
REDMOTE and a computer or a cell phone charger.
NOTE: The REDMOTE can be charged using the Mini-USB connector while connected and controlling a camera wirelessly.
NOTE: If the computer / cable / hub do not provide enough voltage, the REDMOTE will not charge and show an "Error Charging" message.
1. Connect the USB connector to any computer (computer must be ON to charge REDMOTE).
2. Connect the Mini-USB end to the REDMOTE USB Port located on the lower right side (under rubber protective cover).
3. If the REDMOTE is powered down (and paired camera is OFF), the REDMOTE will power UP, display
STARTING UP, display SEARCHING (with flashing Green LED), then settle into IDLE mode.
4. Green battery indicator will blink, indicating REDMOTE is charging.
5. A fully discharged REDMOTE battery will be fully charged in approximately 6 hours.
192
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
UPGRADING REDMOTE FIRMWARE
The REDMOTE update utility allows you to upgrade the firmware on your REDMOTE.
NOTE: After firmware has been upgraded, the REDMOTE must be paired to the camera again.
SETUP
CONFIGURING REDMOTE CONNECTION WITH COMPUTER (MAC)
The first step in upgrading REDMOTE firmware is to establish communication between the MAC and the
REDMOTE.
1. Connect a USB to mini-USB cable between the computer and the USB connector on the
REDMOTE.
2. Go to System Preferences and choose Network. This may open automatically when the REDMOTE is connected.
3. Look for a device called RNDIS/ ...Gadget.
4. Change Configure IPv4 setting to “Manually” (as shown).
5. In the IP Address field, enter 192.168.0.1 (as shown).
6. In the Subnet Mask field, enter 255.255.255.0 (as shown).
7. The Status should change to “Connected” after changes.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
193
NOTE: After entering the IP address as shown above you may not connect during the upgrade procedure. When you go back and check the IP address you see that it is 0.0.0.0 HOWEVER the status of the device is shown as “Connected”.
If this is the case, you may need to enter the IP address a second or possibly a third time to make it stick.
8. Click “Apply’ at the bottom of the Network window.
9. Proceed to UPGRADING REDMOTE FIRMWARE.
UPDATING REDMOTE FIRMWARE
The following information will guide you through proper updating of your REDMOTE firmware.
MAC
1. Download the camera upgrade EPIC_vX.X.XX zip file located at http://www.red.com/support .
2. The file will unzip automatically when downloaded. The REDMOTE Upgrade is located in this download.
3. Navigate to the downloads folder and open the newly created EPIC_vX.X.XX folder; or open it directly from the downloads window.
4. Open the REDmoteUpgrade_vXXX folder.
5. Open the MAC folder.
6. Double-click the REDmoteUpgradeApp. A Terminal window will open and the REDMOTE Software
Wizard will open.
194
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
7. Click “Connect”. When REDMOTE has been established, “Connection to REDMOTE has been achieved” will be displayed.
NOTE: If REDMOTE does not connect, verify that the IP address set under CONFIGURING
REDMOTE CONNECTION WITH COMPUTER (MAC) has held. If not, enter it again as outlined in the procedure.
8. Click "Select File" and navigate to the redmote.1.bin file located in the REDmote_firmware_vXXX folder.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
195
9. Select "Start upgrade".
10. File transfer status will be displayed as a Blue bar.
11. “Updating Firmware” will be displayed with a Green status bar showing upgrade progress.
REDMOTE will also display UPGRADE during this process.
196
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
12. Once the File Transfer Status is completed, the REDMOTE Software Wizard will display “Please Wait and Don’t Unplug – Firmware Upgrade is in Progress on REDMOTE”.
13. After a few more seconds, the REDMOTE Software Wizard will display “Firmware Upgrade
Successfully Done”. Select OK.
14. The REDMOTE Software Wizard will disconnect from the REDMOTE.
15. REDMOTE will reboot.
16. REDMOTE upgrade is complete. REDMOTE will display “POWER UP”, then “SEARCHING” once the upgrade has completed. Finally displaying “Camera: RESCAN…” and going into IDLE mode.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
197
17. Verify the current REDMOTE firmware version by selecting SETUP > SETUP SYSTEM on the
REDMOTE.
18. REDMOTE upgrade is complete. You can now reconnect to the camera.
NOTE: Pairing of the REDMOTE may not be necessary after upgrading the REDMOTE firmware, however after upgrading the camera firmware, you must pair the REDMOTE again.
WINDOWS
Install Upgrade Utility
This procedure outlines installation of the REDMOTE Upgrade Utility for Windows computers.
1. Download the REDMOTE Update zip file to your desktop.
2. Uncompress the zip file.
3. Open the newly created folder.
4. Double-click on the REDMOTE_upgrade_setup.exe file to install the program.
198
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
5. Select “I Agree” to the license agreement.
6. On the Choose Components screen, select Install REDMOTE Firmware.
7. Select “Next”.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
199
8. Choose location to install the REDMOTE Upgrade Utility .
9. Choose the location for the shortcut.
200
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
10. The program will now install. A progress bar is displayed while installing. When complete, select
Close.
11. The REDMOTE Upgrade Utility installation is complete.
Upgrading REDMOTE Firmware
The following information will guide you through proper upgrading of your REDMOTE firmware on
Windows computers using the REDMOTE Upgrade Utility.
1. Connect a USB to mini-USB cable between the computer and the USB connector on the
REDMOTE.
2. Ensure the REDMOTE wakes up and displays the “Total Cameras Found” screen.
NOTE: When properly connected to the PC, the battery charge indicator will be Green and blink.
3. Under Programs, locate REDMOTE_update and open the program.
4. The REDMOTE Upgrade Utility window will open.
5. Select “Connect” to establish communication between the REDMOTE and REDMOTE Update.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
201
NOTE: If when connecting, communication is not established quickly, close the Upgrade Utility, open it again and select Connect again. This may have to be repeated a few times until communication is established.
6. When connected, ”Connection is Established with REDMOTE” is displayed.
7. To begin upgrade, click on “Select File”.
8. Navigate to the *.bin file for updating the REDMOTE firmware.
NOTE: If you choose an incorrect file, click on “Select File” again to locate the correct file.
NOTE: Only one file can be added for upgrade.
202
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
9. The selected file is shown in the window. In this case the selected file is: REDmote.1.bin.
10. After selecting and verifying the correct file for upgrading the REDMOTE, select “Start Upgrade”.
11. During the upgrade, the REDMOTE Software Wizard will display “Please Do Not Unplug” as well as a status bar showing “File transfer progress.”
12. During the upgrade, the REDMOTE will display “Upgrading Firmware” as well as a status bar showing upgrade progress.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
203
13. When upgrade is complete, the REDMOTE will automatically reboot and display “REBOOTING” on the screen.
14. The REDMOTE Software Wizard will display “Firmware Upgrade Successfully Done”.
15. Verify the current REDMOTE firmware version by selecting SETUP > SETUP SYSTEM on the
REDMOTE.
204
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
16. Select “Disconnect” on the REDMOTE Upgrade Utility.
17. REDMOTE firmware upgrade is complete.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
205
APPENDIX F: 3D SETUP / OPERATION
OVERVIEW
The following information outlines basic procedures to connect two RED DSMC cameras together in a
Master / Slave configuration for 3D operation, operation of cameras in Master / Slave configuration and clip naming conventions for clips recorded on those cameras. The MASTER camera will control only the
METADATA parameters of both cameras. On the SLAVE camera, any other setting outside of these will need to be manually changed before recording.
CAMERA SETUP
Select one camera to be designated as Master and a second to be designated as Slave.
NOTE: Cameras can also be set up in a MASTER / MASTER and SLAVE / SLAVE configuration. To set as MASTER / MASTER select ALL under TARGET for both cameras. This will allow either camera to make METADATA changes and control record start/stop of both cameras. To set as
SLAVE / SLAVE select NONE under TARGET for both cameras. This allows each camera to control its own METADATA.
MASTER CAMERA
Perform the following steps on the Master camera:
1. Go to SECONDARY MENUS > SETTINGS > SETUP > COMMUNICATION > NAME and give the camera a unique NAME (CAM A, LEFT, etc…).
2. Under TARGET select ALL.
3. Give the camera a unique IP address.
4. Go to SLAVE CAMERA.
206
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
SLAVE CAMERA
Perform the following steps on the Slave camera:
1. Go to SECONDARY MENUS > SETTINGS > SETUP > COMMUNICATION > NAME and give the camera a unique NAME (CAM B, RIGHT, etc…).
2. Under TARGET select NONE.
3. Give the Slave camera a unique IP address different from the Master.
CLIP NAMING CONVENTIONS
REEL NO. / SLATE (CAMERA ID) / CAMERA POSITION
Before shooting in Master / Slave or Master / Master configuration for a Stereo / 3D production, make sure the Camera Slate (i.e. Reel No. and Cam ID) are set to the same value for both Master and Slave cameras. Then change the Cam Pos value from the system default of CENTER, to either LEFT or RIGHT to identify the "left eye" and "right eye" camera in the stereo pair.
The Reel No, Cam ID and Cam Pos can be set when formatting the media or after formatting by using the SET option. Refer to SECONDARY MENUS > MEDIA.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
207
For example, if Master is set to LEFT and Slave is set to RIGHT and both Cam IDs are set to S, the first clip recorded by this stereo camera configuration will be:
-
Master: S001_L001_0503B6.R3D
-
Slave: S001_R001_0503R7.R3D
Where 0503 represents 05 March, B6 and R7 are examples of camera generated wildcard characters.
Note: If both Master and Slave cameras are accidentally left in default settings of CENTER and
CAM A ID, the clips recorded on each camera will have the same file structure, with the exception of the camera generated wildcard characters which protect against exact file name duplication:
-
Master: A001_C001_0503B6.R3D
-
Slave: A001_C001_0503R7.R3D
CONNECTING CAMERAS
1. While still powered up, interconnect the cameras using a Master/Slave GIG-E Cable P/N 790-0163.
Plug the cable into the GIG-E connector on the rear of each camera body..
2. Power down both cameras, then power back up. If properly connected, LAN will illuminate Green on the UI.
3. Connect a SYNC cable P/N 790-0154 to each camera and connect as to your 3 rd party device.
• Yellow BNC connector is for SMPTE unbalanced Timecode input.
208
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
• Green BNC connector is for Tri-Level Sync (Genlock) input.
• White BNC connector is a dual-purpose (Shutter SYNC input or GPI) input.
4. Go to SETTINGS > SETUP > GPIO/SYNC > SYNC MODE and select GENLOCK.
5. Verify the camera’s project frame rate matches the Genlock and Timecode generator(s) framerate(s).
6. When properly connected and synchronized, TC, GEN and SYNC will illuminate Green on the UI.
OPERATION
CHANGING SETTINGS
When changes are made to the Master camera settings, the Slave camera setting will also change, but not in real-time. For example, when you change the Frame Rate on the Master camera, you will not see the change on the Slave camera until you set the Master camera at the new Frame Rate.
Also when making changes to the Secondary menu settings, the Slave camera will not display those changes unless it affects items displayed on the main screen (example: when HDRx is enabled on the
Master camera, HDR will change to HDRx on the Slave camera).
RECORDING
When the power/record button is pressed on the Master camera to start/stop recording, the Slave camera will also start/stop recording.
POWER DOWN
When the Master camera is powered down using the Secondary Menu > Power, the Slave camera will also power down.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
209
APPENDIX G: EXPOSURE – USING FALSE COLOR AND ISO
NOTE: The following section uses a RED ONE camera display to illustrate exposure tools; however, the same principles apply to RED DSMC camera systems.
RED DSMC cameras provide several advanced exposure indication tools. In the following examples, we will show how these tools respond to a reference scene that is under-exposed, over-exposed and then correctly exposed. Each scene will have its unique characteristics so the “correct exposure” is a matter of judgment, balancing the desire to avoid clipping any highlights and also avoiding underexpose of elements in deep shadow – which may therefore be prone to noise when developed in post-production.
The following reference scene includes highlight and shadow elements and was shot at ISO 800.
UNDEREXPOSURE (~ 2 STOPS)
ISO 800 - Monitor Output
In the image above it is obvious the camera is under exposed. The initial clues are the monitor is very dark, and the histogram is justified to the left. Also note that red bar at the left edge of the histogram and the vertical color stack to the right of the histogram is only at grey. These indicators are saying a significant amount of the senor’s RAW data is “in the noise” and that the peak level of the sensor’s RAW data is at a very low level – in fact less than halfway.
210
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ISO 800 - False Color: Exposure
Select False Color – Exposure: note the √ E icon in the GUI when active. This mode allows us to visualize where in the image underexposure is taking place. These areas are indicated in purple. It is clear those areas are under the matchbox and coin, and between the bottle and cigar holder.
955-0002_v3.2, Rev-A1
ISO 800 - False Color: Video
COPYRIGHT © 2012 RED Digital Cinema
211
Select False Color – Video: note the √ V icon in the GUI when active. This mode allows us to check the
RGB video levels of the scene. As the peak white chips on the test chart are showing up in green and the underexpose areas are showing up in dark blue, this says the monitor path video levels are only ranging between 44 IRE and 1 IRE.
Because the scene is under exposed, when the recorded .R3D file is color corrected in post-production, the scene’s highlight information will certainly not be clipped, however the shadow information will probably display with significant noise once pushed to an acceptable brightness.
OVEREXPOSURE (~ 2 STOPS)
ISO 800 - Monitor Output
In the image above it is obvious the camera is over exposed. The monitor is very bright and the histogram is justified to the right. Note the red bar at the right edge of the histogram and the vertical color stack to the right of the histogram is showing red plus the three traffic lights to the right of that are all illuminated. These indicators are suggesting that a signification portion of the sensor’s RAW data is
“at clip”, and this clipping is occurring on Red, Green and Blue channels.
212
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ISO 800 - False Color: Exposure
Select False Color – Exposure: note the √ E icon in the GUI when active. This mode allows us to visualize where in the image over exposure is taking place. These areas are indicated in red. It is clear those areas are on the highlight on coin, and at the top right edge of the color chip test chart.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
213
ISO 800 - False Color: Video
Select False Color – Video: note the √ V icon in the GUI when active. This mode allows us to check the
RGB video levels of the scene. As all the white chips on the test chart are Yellow, this suggests that a significant portion of the monitor path video is at the maximum legal 100 IRE value.
Because the scene is over exposed, when the recorded .R3D file is color corrected in post-production, the scene’s highlight information will almost certainly be clipped, however the shadow information will probably display cleanly once pulled back down to an acceptable brightness.
214
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
APPROPRIATE EXPOSURE
ISO 800 - Monitor Output
In this image, the camera is appropriately exposed for this scene. The monitor is neither very dark nor very bright and the histogram is spread evenly given that there are bright highlights on the coin we wish not to blow out. Note that there is no red bar on either the left or the right edges of the histogram and the vertical color stack to the right of the histogram is at yellow. These indicators suggest that there is no significant amount of the sensor’s RAW data “in the noise” or “at clip”, and that the peak level of the sensor’s RAW data is about 2/3 stop below clipping.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
215
ISO 800 - False Color: Exposure
Select False Color – Exposure: note the √ E icon in the GUI when active. This mode allows us to visualize where there is under exposure (purple) or over exposure (red) in the image. In this case, there is a very small area of purple under the cracker box, and just a suggestion of red on the highlight on the coin, which suggested that the sensor is appropriately exposed for this scene.
216
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ISO 800 - False Color: Video
Select False Color – Video: note the √ V icon in the GUI when active. This mode allows us to check the
RGB video levels of the scene. The two green squares in the upper right corner of the color chart and green in the background indicate that the scene’s mid grey and skin tone elements, plus peak white and blacks are all at appropriate levels.
Because the scene was well exposed, when the recorded clip is color corrected in post-production, sufficient headroom exists for the scene’s highlight information to be displayed without clipping, and the shadow information can be displayed without significant noise, even if the brightness of the shadow information is pulled up.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
217
ADJUSTING THE ISO RATING
In the following two examples, the image exposed at ISO 800 rating have had the ISO rating adjusted first to ISO 6400 and then to ISO 100.
NOTE: Although the image and Histogram both adjust to changes in the ISO rating, the sensor
RAW meters do not change – they always indicate what is happening at the sensor level and hence where the image is truly in noise or at clipping.
ISO 6400 - No Exposure Adjustment
218
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
ISO 100 - No Exposure Adjustment
In these extreme examples, it is clear that the RGB domain images are respectively very bright and very dark. The histogram data reflects that, however you can also see that the sensor RAW meters are unchanged. The exposure at the sensor at this point in time is the same. If you choose to close the iris to reduce the brightness of the first image you will be reducing exposure at the sensor – this biases exposure in favor of protecting the scene highlight. Alternatively, if you choose to open the iris to increase the brightness of the image of the second image you will be increasing exposure at the sensor
– this biases exposure in favor of minimizing noise in the scene shadows.
The technique is similar in principle to re-rating a film stock. With practice, the ISO rating can be used as a tool to assist ideal exposure based on the dynamic range identified within the scene.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
219
APPENDIX H: POST-PRODUCTION
RED workflow is quite easy to understand, especially if you have experience with photographic RAW image processing, or shoot 16mm or 35mm film followed by a telecine transfer to video for non-linear video editing and on-line conform.
The RAW data captured by RED cameras has wide dynamic range and color space, so you can freely change the white balance, adjust exposure and alter highlight and shadow tonality in post-production.
The RED DSMC camera records RAW sensor data using wavelet based REDCODE RAW compression to REDMAG 1.8” SSD. The compressed RAW data is then transferred from the digital media to a
Macintosh OSX or Windows XP workstation running REDCINE-X PRO post-production software. These applications do not directly edit or conform the RAW data themselves, but prepare the RAW data for editing and conforming by RGB domain post-production software applications.
In film processing terms, REDCINE-X PRO act as an integrated film laboratory, telecine, and one light color corrector. It converts recorded REDCODE RAW data to RGB video, and provides basic one light image processing and color correction. Using REDCINE-X PRO, footage can also be cropped, resized, or repositioned.
REDCINE-X PRO can also encode 4K or 2K RAW footage into a variety of uncompressed RGB and compressed 4:2:2 video formats. For film out, multi-media or special effects applications, REDCINE-X
PRO may export a sequence of 2K or 4K image files in TIFF, Open EXR, DPX, JPEG, or Photoshop PSD file formats.
Provided the appropriate QuickTime codecs are available on the host computer workstation, compressed video choices include ProRes, DNxHD, DV100 and M-JPEG QuickTime movies at 1080p or
720p resolution, providing compatibility with the majority of non-linear editing systems.
Depending on the QuickTime movie resolution, material may be taken directly to a broadcast delivery videotape format, or after the editorial decisions have been made, video can be conformed at full image resolution by replacing the lower resolution edit proxy with a high resolution 4K, 2K or 1080p image file.
MONITORING
When using RED Digital Cinema software tools it is recommended your monitor should be set to Adobe
1998, or to SMPTE-C display profile. If you use the HD Cinema display profile, adjust the gamma to 2.2.
220
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
REDCINE-X
®
PRO
REDCINE-X PRO is available for Intel based Mac OSX and Windows XP platforms. The application performing white balance and one light color correction, image pan/scan, crop and scaling operations.
The application can export either a single clip, or a sequence of clips, as 4K or 2K resolution 10-bit DPX or 16-bit TIFF files. REDCINE-X PRO can also render clips into standalone QuickTime movies using a variety of video codecs including H.264, Apple ProRes and Avid DNxHD
REDCINE-X PRO is available for download at http://www.RED.com/support . The REDCINE-X PRO
Operation Guide Is included with the download package.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
221
APPENDIX I: MAINTENANCE
WARNING: DO NOT attempt to modify, dismantle or open your camera, lens or other accessory as doing so may expose you to electric shock and serious injury. There are no user-serviceable parts inside. Alteration or repairs made to the camera, lens or other accessory, except by a RED authorized service facility, will void the Limited Warranty.
CLEANING
All RED products are designed for rugged durability, but precision instruments demand proper care.
Please note the following care guidelines:
WARNING: DO NOT rinse or immerse any element of the camera, lens or other accessory, keep them dry at all times.
WARNING: DO NOT use soaps, detergents, ammonia, acetone, alkaline cleaners, abrasive cleaning compounds, or solvents. These substances may damage lens coatings and electronic circuitry.
CAMERA AND ACCESSORY EXTERIOR SURFACES
Clean ONLY using a dry cloth. When cleaning your camera and accessories, remember that it is not waterproof and moisture can damage electronic circuitry.
BRAIN
OPTICAL LOW-PASS FILTER (OLPF)
If equipped with an OLPF, use Delkin Devices Digital Duster Kit (P/N DDSS-DUSTER2) or equivalent to clean OLPF surface.
LCD SCREEN (TOUCHSCREEN / NON-TOUCHSCREEN)
The specialized AR and AS coatings on RED TOUCH LCD displays must be treated with special care to avoid scratching. To help maintain the specialized AR and AS coatings on RED TOUCH LCD displays, the RED TOUCH LCD comes with a RED Microfiber bag for cleaning and storage. Using it will preserve the superior quality of these coatings. Hand wash and air-dry the RED Microfiber bag regularly.
NOTE: RED’s warranty does not cover any LCD display against scratches or damage due to use of improper chemicals to clean the LCD.
ONLY USE a RED Microfiber bag or equivalent Photographic Solutions PEC*PADs (P/N 05011) and
Isopropyl Alcohol (>95%) or equivalent Pancro Professional Lens Cleaner (P/N PANCROCLN) to clean the screen on Touchscreen and Non-Touchscreen LCDs.
222
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
DO NOT USE any other solvents, chemicals or third party cleaning kits because they have not been tested on RED TOUCH LCD displays and can possibly damage them. Not approved for use on RED
TOUCH LCD displays:
• Rubbing Alcohol
• Isopropyl Alcohol (<90%)
• Windex
• Pre-packaged lens cleaner containing any additives, such as detergent, anti-static, fragrance, etc.
For proper cleaning and storage, remember to protect the RED TOUCH LCD by storing it in the RED
Microfiber bag.
EVF
Use Pancro Professional Lens Cleaner (P/N PANCROCLN) and Photographic Solutions PEC*PADs (P/N
05011) or equivalent to clean the viewfinder lens. Ensure your spray the solution onto the pad and not directly onto the lens surface.
REDMOTE SCREEN
Use Pancro Professional Lens Cleaner (P/N PANCROCLN) and Photographic Solutions PEC*PADs (P/N
05011) or equivalent to clean the screen on Touchscreen and Non-Touchscreen LCDs.
LENSES
Use Pancro Professional Lens Cleaner (P/N PANCROCLN) and Photographic Solutions PEC*PADs (P/N
05011) or equivalent to clean the viewfinder lens. Ensure your spray the solution onto the pad and not directly onto the lens surface.
SIDE HANDLE LCD
Use Pancro Professional Lens Cleaner (P/N PANCROCLN) and Photographic Solutions PEC*PADs (P/N
05011) or equivalent to clean the screen on the Side Handle LCD.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
223
BACK FOCUS ADJUSTMENT
WARNING: THERE IS A SCREW-IN METAL PLUG INSTALLED IN THE CAMERA BODY COVERING
THE BACK FOCUS SCREW. THIS PLUG MUST BE REMOVED BEFORE PERFORMING A BACK
FOCUS ADJUSTMENT. TO REMOVE THE PLUG, USE A T-10 TORX SCREWDRIVER.
NOTE: To perform this procedure as written, you must have a PL mount and RED Focus™.
Back focus is adjusted by turning the back focus adjustment on the top of the camera’s front plate using a T-10 Torx screwdriver. This screw is indicated by a Siemens Star with an arrow pointing to its location.
Back Focus Adjustment Location
1. Remove the screw-in plug located in the back focus adjustment opening using a T-10 Torx screwdriver.
2. Place the camera on a level, stable surface or mount the camera on a tripod.
3. Install RED Focus to the camera PL mount. a. Remove the camera lens or sensor cover if equipped. b. Install RED Focus onto the camera in the position shown. c. Ensure RED Focus is secured to the camera with the camera lock ring.
224
RED Focus Properly Installed on Camera
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
4. Power up the camera.
5. Power up RED Focus. Refer to POWER UP / DOWN.
NOTE: Remember that RED Focus will AUTOMATICALLY power down after 3 minutes. Press the Red button on the front to power back up.
6. Set the camera to Magnify. Go to SECONDARY MENUS > SETTINGS > DISPLAY > FALSE COLOR
> MAGNIFY.
NOTE: The “Focus” option located under SECONDARY MENUS > SETTINGS > DISPLAY >
FALSE COLOR > FOCUS can serve as a good double-check for proper focus during this procedure.
RED Focus Displayed Image on Camera
7. Insert a T-10 Torx screwdriver into the back focus adjustment screw. The screw is oriented at approximately 80° as shown.
Performing Back Focus Adjustment
8. Carefully and slowly, rotate the back focus adjustment screw to achieve optimum focus.
-
Turning CLOCKWISE moves the sensor forward.
- Turning COUNTER-CLOCKWISE moves the sensor rearward.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
225
NOTE: The center of the image will never be in perfect focus as the lines are less than 1/3 of a pixel in size.
9. The back focus adjustment mechanism is self-locking, and does not require a supplementary locking screw.
10. Install the screw-in plug in the back focus adjustment opening using a T-10 Torx screwdriver.
11. This completes the back focus adjustment.
226
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
APPENDIX J: TROUBLESHOOTING
NO MEDIA ATTACHED
Displayed if media is not present or not formatted when pressing the record button. Connect media to camera if necessary. If media is already connected, format media and attempt to record again. Refer to
APPENDIX B: MANAGING DIGITAL MEDIA for detailed information.
RECORDING HALTED: RECORD ERROR - SHUTDOWN
Displayed if media removed while recording. DO NOT remove media while camera is recording. Power down the camera, verify the media is inserted properly (inspect connectors for damage), power up and resume recording.
PRESET COULD NOT BE APPLIED
If the preset could not be applied, “Preset Could Not Be Applied” will appear to inform you. Power down camera, power back up and attempt to apply the preset that failed.
CAMERA CANNOT BE PAIRED TO REDMOTE
• Ensure REDMOTE display indicates IDLE before attempting to pair the camera to the REDMOTE.
• Ensure the REDMOTE is detached from the rear of the camera body and powered on.
• Ensure the REDMOTE wireless in turned on.
• Ensure camera does not display REDLINK Upgrade Required.
CANNOT SEE MENUS ON LCD TOUCH SCREEN
Double tap the LCD screen to exit clean mode.
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
227
APPENDIX K: TECHNICAL SPECIFICATIONS
SENSOR
PIXEL ARRAY
S/N RATIO
DYNAMIC RANGE
MAX IMAGE AREA
LENS COVERAGE
DEPTH OF FIELD
ACQUISITION FORMATS
PROJECT FRAME
RATES
DELIVERY FORMATS*
PROGRAM OUTPUT
MONITOR OUTPUT
DIGITAL MEDIA
REDCODE™
AUDIO
MONITORING OPTIONS
REMOTE CONTROL
WEIGHT
CONSTRUCTION
TEMPERATURE
RANGES
14 MEGAPIXEL MYSTERIUM-X™
5120 (h) x 2700 (v)
66db
13.5 stops, up to 18 stops with HDRx™
5120 (h) x 2700 (v)
27.7mm (h) x 14.6mm (v) x 31.4 mm (d)
Equivalent to S35mm (Motion) / APS-H (Still) lenses
Equivalent to 16mm (Motion) lens in 2K RAW
5K RAW (Full Frame, 2:1, 2.4:1 and Anamorphic 2:1)
4.5K RAW (2.4:1)
4K RAW (16:9, HD, 2:1 and Anamorphic 2:1)
3K RAW (16:9, 2:1 and Anamorphic 2:1)
2K RAW (16:9, 2:1 and Anamorphic 2:1)
1080p RGB (16:9)
720p RGB (16:9)
23.98, 24, 25, 29.97, 47.96, 48, 50, 59.94 fps, all resolutions
4K : DPX, TIFF, OpenEXR (RED RAY via optional encoder)
2K : DPX, TIFF, OpenEXR (RED RAY via optional encoder)
1080p RGB or 4:2:2, 720p 4:2:2 : Quicktime, JPEG
Avid AAF, MXF. 1080p 4.2.0, 720p 4:2:0 : H.264, .MP4
HD-SDI Clean Feed
2K RGB, 1080p RGB or 4:2:2, 720p 4:2:2
SMPTE Timecode, HANC Metadata, 24-bit 48Khz Audio
HD-SDI and HDMI with Frame Guides and Look Around
2K RGB, 1080p RGB or 4:2:2, 720p RGB or 4:2:2
SMPTE Timecode, HANC Metadata, 24-bit 48Khz Audio
REDMAG (SSD) Module : (64, 128, 256GB Media)
12 and 16-bit RAW : Compression choices of 18:1 to 3:1
1-120 fps 5K, 4.5K; 1-150 fps 4K; 1-200 fps 3K; 1-300 fps 2K
2 channel, uncompressed, 24 bit, 48KHz.
Optional 4 channel, and AES / EBU digital audio.
RED LCD 5" Touchscreen Display
BOMB EVF™ High Definition Viewfinder
Wireless, Ethernet, RS232, GPI Trigger
5lbs. Body only
Aluminum Alloy
Operating Range: 0 ËšC to +40ËšC (32ËšF to 104ËšF)
Storage Range: -20ËšC to +50ËšC (-4ËšF to 122ËšF)
228
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
CAMERA BRAIN DIMENSIONS
Front View
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
229
230
Side View
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Top View
Bottom View
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
231
232
Back View
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
APPENDIX L: RESOLUTION CHART
955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema
233
APPENDIX M: MENU MAPS
234
COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Al t
I T
Di t
E A ks, r names, ng oduct e ogos, ght cons, wr t her el i , oper owned r l associ i vel by Di t nema
advertisement
Related manuals
advertisement
Table of contents
- 1 RED EPIC® OPERATION GUIDE - BUILD 3.2
- 2 TABLE OF CONTENTS
- 2 1 of 2
- 3 2 of 2
- 4 DISCLAIMER
- 4 Copyright Notice
- 4 Trademark Disclaimer
- 5 COMPLIANCE
- 5 Industrial Canada Emission Compliance Statements
- 5 Federal Communications Commission (FCC) Statement
- 6 Australia and New Zealand Statement
- 6 Japan Statements
- 6 European Union Compliance Statements
- 8 BEFORE YOU START
- 8 Important Safety Instructions
- 11 THEORY OF OPERATION
- 11 MYSTERIUM X® Sensor
- 11 Image Processing
- 12 HDRx™
- 13 Magic Motion™
- 13 Audio Recording
- 13 Microphone Level Analog Inputs
- 14 Line Level Analog Inputs
- 14 Video Monitoring Outputs
- 14 Bomb EVF
- 14 RED LCD
- 14 HD-SDI
- 14 HDMI
- 15 RED LCD / Bomb EVF®
- 16 REDMOTE®
- 16 Digital Magazine (Media)
- 17 Metadata
- 17 Clip Naming Conventions
- 19 Multi Camera Shoots
- 19 3D (STEREO) CAMERA SHOOTS
- 19 SMPTE Timecode
- 19 Power Consumption
- 20 CAMERA OPERATIONAL CONTROLS
- 20 Brain
- 21 Side SSD Module
- 23 Side Handle
- 23 Top
- 24 Front
- 25 Rear
- 27 Installation / Removal
- 29 DSMC Modules
- 29 Rear SSD Module
- 29 /
- 29 Quad Battery Module
- 30 Dual Battery Module
- 31 Module Installation / Removal
- 33 Attaching the DSMC Module
- 35 REDMOTE
- 37 Displays
- 37 BOMB EVF and Bomb EVF (OLED)
- 38 Touchscreen LCD
- 39 BASIC OPERATION
- 39 Power Sources
- 39 Side Handle
- 40 Quad Battery Module
- 40 REDVOLT and REDVOLT XL
- 41 BACKPACK QUICKPLATE
- 42 AC POWER ADAPTOR - (DSMC)
- 43 External DC Power
- 44 Power UP
- 45 Power Down
- 46 Graphical User Interface and Navigation
- 46 RED LCD/Touchscreen LCD, BOMB EVF, External Monitors
- 48 Upper Status Row
- 49 Live Action Area
- 49 Lower Status Row
- 49 ICON Behavior
- 49 TC
- 50 GEN
- 50 SYNC
- 50 Power Status
- 51 RAW Clip Meter
- 51 RAW Noise Level Bar
- 51 RAW Clip Level Bar
- 52 Side Handle
- 52 REDMOTE
- 53 Navigating Menus
- 54 Using Touchscreen LCD
- 55 Touchscreen Shortcuts
- 56 Power Down
- 56 Power Menu
- 56 Using Power Status Display
- 57 Lock / Unlock Touchscreen Opreration
- 57 Lock
- 57 Unlock
- 58 FIRST TIME USE – SETTING UP YOUR RED EPIC
- 58 Attach Power Source
- 58 Battery
- 58 Side Handle
- 58 Install
- 59 Remove
- 59 Quad Battery Module
- 59 Install
- 59 Remove
- 60 RED Brick
- 60 DC Power
- 60 Power UP
- 60 Preparing to Record
- 60 Connect and Format Media
- 62 Perform a Black Shading Calibration
- 62 Adjust Project Settings
- 62 Time Base
- 63 Record Resolution
- 63 Record Quality (REDCODE)
- 64 Camera ID (Slate)
- 64 Recording
- 64 Record Indicator
- 65 Playback
- 66 MENU CONTROLS
- 66 Adjustments
- 66 Basic Setting Adjustments
- 66 Side Handle / REDMOTE
- 66 Basic Adjustments Using Side Handle ONLY
- 66 Touchscreen
- 67 Advanced Setting Menus
- 67 Side Handle / REDMOTE
- 67 Touchscreen
- 68 MAIN MENU
- 68 FPS
- 68 Varispeed
- 69 Basic Settings
- 69 Advanced Settings
- 70 ISO (Sensitivity)
- 70 F Stop
- 71 Basic Settings
- 71 Advanced Settings
- 71 Aperture (f stop)
- 72 Focus
- 72 Exposure
- 72 Basic Settings
- 73 Advanced Settings
- 73 Exposure (Speed)
- 74 Integration Time
- 74 Absolute Angle
- 75 White Balance
- 75 Basic Settings
- 76 Advanced Settings
- 76 Preset
- 76 Shade
- 76 Cloudy
- 76 Daylight
- 76 Flash
- 76 Flourescent
- 76 Tungsten
- 76 Incandecent
- 76 Color Temp
- 77 Tint
- 77 Calc White Balance
- 78 Resolution
- 78 REDcode
- 79 REDcode Options for Various Frame Rates
- 79 SECONDARY MENUS
- 79 HDR Menu
- 80 HDR ON / OFF
- 80 Stops
- 80 Focus Menu
- 81 Mode
- 81 Manual Focus
- 81 Manual
- 81 Confirm
- 81 Auto Focus
- 82 Manual
- 82 Confirm
- 82 Single
- 83 Continuous
- 83 Touch Track
- 83 Rack
- 84 DSMC Canon Mount Electronically Supported Lenses
- 85 Zones
- 85 Center
- 86 Spot
- 86 Spot Focus Indicator
- 86 Moving
- 86 Touchscreen
- 87 Side Handle / REDMOTE
- 87 Resizing
- 87 Touchscreen
- 88 Lens Information Display
- 88 RED DSMC Ti PL Mount + Lens
- 88 DSMC Canon Mount + Lens
- 89 Exposure Menu
- 89 Presets Menu
- 89 Camera Presets
- 89 Applying a Preset
- 89 Creating a Preset
- 91 Sharing Presets
- 92 Copy presets from camera to SSD
- 92 Copy presets from SSD to camera
- 92 Managing Preset Files
- 93 LOOKs Presets
- 94 Media Menu
- 94 Select Media
- 94 Format Media
- 95 Reel No.
- 95 Camera ID (Slate)
- 95 Camera Pos (Position)
- 95 Format
- 95 Eject Media
- 96 Utilities
- 96 Secure Format
- 97 Settings Menu
- 97 Display
- 97 Tools
- 97 Off
- 98 Exposure
- 99 Focus
- 99 Video
- 100 Edge
- 101 Magnify
- 102 RAW
- 102 Zebra
- 103 Zebra 1
- 103 High IRE
- 103 Low IRE
- 103 Zebra 2
- 103 High IRE
- 104 Low IRE
- 104 Overlay
- 104 Grid
- 105 Look Around
- 105 Overlay Elements
- 106 Modes
- 106 Exposure
- 106 Shutter
- 106 Absolute
- 106 Relative
- 107 Aperture
- 107 Focal Distance
- 107 Guides
- 108 Size
- 108 Line Style
- 108 Color
- 108 Transparancy
- 108 Monitor
- 109 Brightness Control
- 109 Touch Gestures
- 109 Pinch to Magnify
- 109 Double-Click Right 25% to Record
- 109 Double-Click Left 25% to Start AF
- 109 Look
- 109 Color
- 109 Saturation
- 110 Contrast
- 110 Brightness
- 110 Gain
- 110 Red
- 110 Blue
- 110 Green
- 110 FLUT
- 111 FLUT
- 111 Exposure
- 111 Shadow
- 111 CURvES
- 111 /
- 112 Color/Gamma
- 112 Project
- 113 Time Base
- 113 Time Code
- 114 Time Code Display
- 114 Time Code Source
- 114 User-Provided
- 114 Use RTC Time
- 114 Set Manually
- 115 Slate
- 115 System Status
- 116 Audio/Video
- 116 Audio Input
- 118 Audio Output
- 118 Audio Channels
- 119 Input
- 119 Source
- 119 Mode
- 119 Link
- 120 Limiter
- 120 Output
- 120 Link
- 120 Monitor Control
- 120 Mode
- 120 LCD/EVF
- 120 HDMI
- 121 Res
- 121 HD-SDI
- 121 Res
- 121 Freq
- 121 Automatically Assign Menu Screen if Enabled
- 122 Test Signals
- 123 Setup
- 123 Keys
- 123 Key Mapping
- 124 Options
- 124 Advanced
- 126 Date / Time
- 126 Communication
- 126 Name
- 127 Group
- 127 Target
- 127 Serial Protocol
- 128 Network
- 128 DHCP
- 128 C2C
- 128 EXT
- 128 IP Address
- 128 Netmask
- 128 Gateway
- 129 REDMOTE
- 129 Scan and Pair REDMOTEs
- 129 Manual Channel Select
- 130 GPIO
- 130 Camera Input
- 130 Sync In
- 130 General Purpose In
- 131 Camera Output
- 131 Sync Out
- 131 General Purpose Out
- 132 Sync Mode
- 133 System
- 133 Fan Control
- 133 Auto
- 133 Manual
- 133 Record Speed
- 133 Standby Speed
- 134 Indicators
- 134 Beep Speaker
- 134 EVF Tally Light
- 134 Maintenance
- 135 System Info
- 135 Save Log
- 135 SW Update
- 136 Calibration
- 137 Current CalMap
- 137 Factory
- 137 User HS
- 137 Black Shading (Default)
- 137 Black Shading (Current FPS/Exposure Settings)
- 138 Black Shading Procedure
- 139 Self Test
- 140 Enable / Disable Sensor Test Pattern
- 141 Touchscreen
- 141 Restore System
- 142 Rediscover
- 144 Playback
- 144 Upper Controls
- 144 Exit Playback ICON (Touchscreen)
- 144 ISO
- 145 White Balance
- 145 Advanced Menu
- 145 View
- 146 Presets
- 146 Media
- 147 Touchscreen
- 147 Side Handle / REDMOTE
- 148 Settings
- 148 Display
- 148 Tools
- 148 Zebra
- 149 Look
- 149 Record (Exit)
- 149 Meta
- 150 Clip Playback Status Bar
- 150 Touchscreen
- 150 Side Handle / REDMOTE
- 151 Lower Controls
- 151 Resolution / Project Framerate / Quality
- 151 Histogram
- 151 Playback Speed
- 152 In / Out Point Marker
- 152 Frame-by-Frame Reverse / Forward
- 152 Play / Pause
- 152 Play Once / Loop
- 153 Playback Direction
- 153 Additional Clip/Camera Information
- 153 Power
- 153 Power Status
- 154 Shutdown
- 155 APPENDIX A: UPGRADING CAMERA FIRMWARE
- 155 Verify Current Camera Firmware
- 155 Upgrade Procedure
- 156 APPENDIX B: MANAGING DIGITAL MEDIA
- 156 Media
- 156 Formatting Media
- 158 Media Capacity Remaining Status
- 158 Eject Media from Camera (Unmount)
- 158 Using REDMOTE / Touchscreen LCD
- 159 Using Side Handle
- 159 Using Side SSD
- 159 Copying Media
- 160 Erasing Media
- 160 Macintosh OS X
- 160 Windows
- 161 APPENDIX C: INPUT / OUTPUT CONNECTORS
- 161 Camera Brain Front
- 162 MIC-1, MIC-2 (Microphone Audio)
- 163 Camera Brain Rear
- 164 HD-SDI
- 165 Headphone
- 165 SYNC (Video Sync)
- 168 CTRL (RS232 Control)
- 169 GIG-E (Ethernet)
- 170 DC IN (Power Input)
- 171 HDMI Out
- 172 Side SSD Module
- 173 REDMOTE
- 174 APPENDIX D: DEFAULT KEY FUNCTIONS
- 176 APPENDIX E: REDMOTE OPERATION
- 176 Control, Connectors and Display
- 176 Controls
- 176 Still / Motion Switch
- 177 LEDs
- 177 Rocker Switch
- 177 User Function Keys
- 177 Menu Button
- 177 SOFT Menu Buttons 1-3
- 177 Navigation Group
- 178 Scroll Wheel
- 178 Direction KEYS
- 178 Enter Button
- 178 Focus and Record Button
- 179 Soft Menu Buttons 4-8
- 179 Power / KEY Lock Switch
- 179 USB Power Port
- 179 Operation
- 179 Docking and Undocking
- 179 Docking
- 180 Undocking
- 180 Power Up / Down
- 181 Power UP
- 181 Connected to Camera
- 181 Not Connected to Camera
- 181 Power DOWN
- 181 Using Camera
- 181 Using REDMOTE
- 182 Recording
- 182 Accessing Camera Controls / Settings
- 183 Changing Camera Settings
- 183 Using Camera LCD / External Monitor as Reference
- 183 Exiting Menus to Main Screen
- 183 Using REDMOTE LCD Stand-Alone
- 184 ADVANCED OPERATION: REDMOTE Menus
- 184 Soft Menu Buttons 1-3
- 184 WIRELESS CONNECT: SOFT MENU BUTTON 1
- 184 Connect REDMOTE to a Paired Camera
- 186 CANCEL
- 187 DISCONNECT
- 187 ReconnectING IF Signal is Lost
- 188 Operating WITH Multiple Cameras FROM a REDMOTE
- 188 REDMOTE or LOCAL MENUS: SOFT MENU BUTTON 2
- 189 REMOTE
- 189 LOCAL
- 189 CUSTOMIZING LOCAL MENUS.
- 190 REDMOTE SETUP: SOFT MENU BUTTON 3
- 191 Brightness
- 191 Volume
- 191 Auto Shutdown
- 191 DISPLAY LAYOUT: Soft Menu Buttons 4-8
- 192 Maintenance
- 192 Internal Battery
- 192 Charge Status
- 192 Battery Life
- 193 CHARGING
- 193 CHARGE TIME
- 193 USING CAMERA
- 193 USING USB CONNECTOR
- 194 Upgrading REDMOTE Firmware
- 194 Setup
- 194 Configuring REDMOTE Connection with Computer (MAC)
- 195 Updating REDMOTE Firmware
- 195 MAC
- 199 Windows
- 199 Install Upgrade Utility
- 202 Upgrading REDMOTE Firmware
- 207 APPENDIX F: 3D SETUP / OPERATION
- 207 Overview
- 207 Camera Setup
- 207 Master Camera
- 208 Slave Camera
- 208 Clip Naming Conventions
- 208 Reel No. / Slate (Camera ID) / Camera Position
- 209 Connecting Cameras
- 210 Operation
- 210 Changing Settings
- 210 Recording
- 210 Power Down
- 211 APPENDIX G: EXPOSURE – USING FALSE COLOR AND ISO
- 211 Underexposure (~ 2 stops)
- 213 Overexposure (~ 2 stops)
- 216 Appropriate Exposure
- 219 Adjusting the ISO Rating
- 221 APPENDIX H: POST-PRODUCTION
- 221 Monitoring
- 222 REDCINE-X® PRO
- 223 APPENDIX I: MAINTENANCE
- 223 Cleaning
- 223 Camera And Accessory Exterior Surfaces
- 223 Brain
- 223 Optical Low-Pass Filter (OLPF)
- 223 LCD Screen (Touchscreen / Non-Touchscreen)
- 224 EVF
- 224 REDMOTE Screen
- 224 Lenses
- 224 Side Handle LCD
- 225 Back Focus Adjustment
- 228 APPENDIX J: TROUBLESHOOTING
- 228 No Media Attached
- 228 Recording Halted: Record Error - Shutdown
- 228 Preset Could Not Be Applied
- 228 Camera Cannot Be Paired to REDMOTE
- 228 Cannot See Menus on LCD Touch Screen
- 229 APPENDIX K: TECHNICAL SPECIFICATIONS
- 230 Camera Brain Dimensions
- 234 APPENDIX L: RESOLUTION CHART
- 235 APPENDIX M: MENU MAPS
- 236 1 of 4
- 237 2 of 4
- 238 3 of 4
- 239 4 of 4