PRO 3600 / 4600 Pouch Laminators Instruction Manual

PRO SERIES 3600 / 4600
TM
Pouch Laminators
Instruction Manual
Rear of machine
Pouch exit outlet
Main power switch
Cable socket
Pouch insertion slot
Power cord
Control panel
A
B
C
D
E
F
Display Panel
READY - Indicate that the machine is
ready to laminate.
TEMPERATURE - Indicate the
temperature setting.
HOT - Indicate that the HOT function
is selected.
SPEED - Indicate the speed setting.
COLD - Indicate that the COLD function
is selected.
- Indicate that the heater is operating.
MEAS - Indicate that measure roller temperature function is selected.
- Indicate that the roller is
moving in reverse revolution.
- Indicate that the roller is
moving in forward revolution.
- Indicate that the cooling fan is operating.
Switch Panel
- Power ON/OFF the machine.
- Memory mode for saving frequent
use temperature and speed setting.
- Preset mode for hot lamination.
- Preset mode for cold lamination.
- Display current roller temperature (approx. 3 seconds).
- Reverse the revolution of the rollers to correct misfeeds.
- Stop/start the revolution of the rollers.
- These keys are used to increase or
decrease temperature ( 0~140°C).
- These keys are used to adjust the speed
(1~9) of the rollers. Speed 9 is the fastest
speed.
Safety instructions
:0634"'&5:"48&--"45)&4"'&5:0'05)&34*4
IMPORTANT TO ACCO BRANDS. IN THIS INSTRUCTION
MANUAL ARE IMPORTANT SAFETY MESSAGES. READ
THESE MESSAGES CAREFULLY.
THE SAFETY ALERT SYMBOL PRECEDES EACH
SAFETY MESSAGE IN THIS INSTRUCTION MANUAL.
THIS SYMBOL INDICATES A POTENTIAL PERSONAL
SAFETY HAZARD THAT COULD HURT YOU OR
OTHERS, AS WELL AS CAUSE PRODUCT DAMAGE
OR PROPERTY DAMAGE.
Special notice
Thank you, for your recent purchase of a GBC Pouch Laminator.
Your new laminator may emit a slight odour during the initial
stage of operation. It is normal and will diminish after several
hours of operation.
Cleaning
Caution: Unplug this product before cleaning.
t8JQFFYUFSJPSPOMZXJUIBEBNQDMPUI%POPUVTF
detergents or solvents.
t%POPUVTFBFSPTPMEVTUFSTPSDMFBOFST
t%POPUTQSBZBOZUIJOHJOUPUIFNBDIJOF
Service
t%POPUBUUFNQUUPTFSWJDFPSSFQBJSUIFQPVDIMBNJOBUPS
yourself. Unplug the unit and contact an authorised ACCO
Brands service representative for any required repairs.
Important safeguards
WARNING: FOR YOUR PROTECTION DO NOT
CONNECT THE POUCH LAMINATOR TO
ELECTRICAL POWER UNTIL YOU READ THESE
INSTRUCTIONS COMPLETELY. KEEP THESE
INSTRUCTIONS IN A CONVENIENT LOCATION
FOR FUTURE REFERENCE. TO GUARD AGAINST
INJURY, THE FOLLOWING BASIC SAFETY
PRECAUTIONS MUST BE OBSERVED IN THE
SET-UP AND USE OF THIS PRODUCT.
General safeguards
t6TFUIFVOJUPOMZGPSJUTJOUFOEFEQVSQPTFTPGMBNJOBUJOH
documents.
t%POPUQMBDFBOZUIJOHJOUIFUISPBUPQFOJOHPGUIF
laminator other than pouches/documents.
t1MBDFVOJUPOBTFDVSFTUBCMFXPSLBSFBUPQSFWFOUUIFVOJU
from falling and possibly causing personal injury and
damage to the unit.
t'PMMPXBMMXBSOJOHTBOEJOTUSVDUJPOTNBSLFEPOUIFVOJU
t5IFTPDLFUPVUMFUTIBMMCFJOTUBMMFEOFBSUIFFRVJQNFOU
and shall be easily accessible.
t%POPUBUUFNQUTJOHMFTJEFMBNJOBUJPOUIJTXJMMEFTUSPZUIF
laminator.
t%POPUCMPDLUIFWFOUTMPUTUIJTXJMMDBVTFUIFMBNJOBUPSUP
overheat.
Electrical safeguards
t5IFVOJUNVTUCFDPOOFDUFEUPBTVQQMZWPMUBHF
corresponding to the electrical rating shown on the unit.
t6OQMVHUIFVOJUCFGPSFNPWJOHJUPSXIFOJUJTOPUJOVTF
for an extended period of time.
t%POPUPQFSBUFXJUIBEBNBHFETVQQMZDPSEPSQMVH%P
not alter the attachment plug. The plug is configured for
the appropriate electrical supply.
t%POPUPWFSMPBEFMFDUSJDBMPVUMFUTCFZPOEUIFJSDBQBDJUZmSF
or electrical shock could result.
t5IFVOJUJTJOUFOEFEGPSJOEPPSVTFPOMZ
t$MPTFTVQFSWJTJPOJTSFRVJSFEXIFOUIJTQSPEVDUJTVTFE
near children.
Technical specifications
Electrical
Machine Dimensions
Machine Weight
Maximum Pouch Width
Maximum Pouch Thickness
Maximum Thru-put Thickness
Warm-Up Time
GBC PRO SERIES TM 3600
220-240V / 50~60Hz / 1050W / 6.0A
GBC PRO SERIES TM 4600
220-240V / 50~60Hz / 1050W / 6.0A
540 x 271 x 112 mm
15.0 kg
330 mm
2 x 350 mic (Total 700)
3.0 mm
6 minutes
691 x 271 x 112 mm
20.0 kg
480 mm
2 x 350 mic (Total 700)
3.0 mm
6 minutes
Operation, hot lamination
1
2
3
Connect power cord to appropriate power source.
Press the power switch on the back of the laminator and press the POWER button for 1 second to turn on the machine (fig. A).
Using the lamination guidelines, select the appropriate temperature setting for the pouch gauge thickness and material you
are laminating.
t*GUIFMBNJOBUFEJUFNBQQFBSTUPCFDMPVEZJUNFBOTUIBUUIFMBNJOBUPSUFNQFSBUVSFJTOPUIPUFOPVHI"MMPXUIFMBNJOBUPS
to heat for a few more minutes then run the pouch through again.
t*GUIFMBNJOBUFEJUFNJTXBWZUIF5&.1&3"563&JTUPPIPU7FSJGZUFNQFSBUVSFTFMFDUPSJTTFUBUUIFBQQSPQSJBUFUFNQFSBUVSF
t"MXBZTBMMPXTVGmDJFOUUJNFGPSUIFMBNJOBUPSUPBEKVTUUPDIBOHFTJOUFNQFSBUVSFTFUUJOH
1.Preset Mode
a
Press HOT button to choose Preset
mode. Machine is set to temperature
100°C / speed 6 and “HOT” symbol
appears on the LCD. (fig. B).
2.Manual Mode
3.Memory Mode
(to change speed and temperature manually):
(to save specific temperature and speed in memory):
a
b
Press the temperature Up/Down
arrow keys to modify the
temperature setting.
Press the speed Up/Down arrow
keys to modify the speed setting.
a
b
c
d
4
5
6
7
Press either button 1 or 2 for one
second to enter memory mode.
Set your frequent use temperature
and speed setting using the
Up/Down arrow keys.
Press the number button again to
save setting to memory.
To use a saved memory, select
either button 1 or 2. The LCD will
indicate the temperature and
speed selected.
As the machine warms up, the heating symbol (
) will flash. 8IFOUIFNBDIJOFJTSFBEZUPlaminate, the laminator will beep
and the “READY” symbol appears on the LCD (fig. C).
Centre the item to be laminated within the pouch left to right with the top edge against the sealed edge of the pouch (fig. D).
Insert the pouch with the sealed edge first into the machine (fig. E).
The laminated item will automatically exit the rear of the machine. After the pouch has stopped moving, immediately place it on
a flat surface to cool for one minute before handling (fig. F).
Operation, cold lamination
1
2
3
4
5
Connect power cord to appropriate power source.
Press the power switch on the back of the laminator and
press the POWER button for 1 second to turn on the
machine.
Press COLD button and “COLD” symbol appears on the
LCD.
8IFOUIFNBDIJOFJTSFBEZUPMBNJOBUFUIFMBNJOBUPSXJMM
beep and the “READY” symbol appears on the LCD.
Use and laminate your cold pouch by pressing the STOP
<RUN> button to start or stop the roller.
CAUTION: If you have just done hot lamination,
press COLD button (to cool down machine) and
wait for the “READY” symbol to reappear on the LCD
before attempting to do cold lamination.
Reverse Button
In the event of a misfeed or a jam follow these instructions.
1 Press the REV button and hold down. This will reverse the
rotation of the rollers allowing the pouch to exit the front
of the machine.
2 Pull the document out of the laminator.
3 After the document is out of the machine clean the rollers
by running the cleaning sheet through the laminator.
CAUTION: Be careful when removing the
laminated pouch from the machine. It may be hot.
Finishing lamination
1
2
3
Press and hold POWER button for one second and “COOL”
symbol appears on the LCD.
After the roller cool down (below 65°C), the laminator will
beep and power will be stopped automatically.
Press the power switch on the back of the laminator to
turn the machine off.
CAUTION: Cooling down the machine before
turning off the power switch protects and extends
the life of the rollers.
NOTE: For added safety and environmental reasons the
laminator will automatically go into sleep mode after
120 minutes of inactivity. If you wish to use the laminator
again, press the POWER button for 1 second to turn on
the machine.
Laminating Tips
t%0/05-".*/"5&"/&.15:106$)
t/FWFSJOTFSUUIFMPPTFFOEPGUIFQPVDIJOUPUIFNBDIJOFmSTU
This could cause the machine to jam.
t#FGPSFMBNJOBUJOHJNQPSUBOUPSVOJRVFEPDVNFOUTBMXBZTSVO
a test pouch through the laminator using a similar type of
document.
t"TTPPOBTIPUMBNJOBUJPOJTDPNQMFUFESFNPWFUIFMBNJOBUJPO
from the front of the machine and place on a cool flat surface
for cooling to prevent the pouch from curling.
t%POPUDVUQPVDIFTQSJPSUPMBNJOBUJPO
Guarantee
ACCO Brands (ACCO) warrants its products and their parts against defects in materials and workmanship under normal use for a
period of 12 months from the original date of purchase. During this period, ACCO will, at its discretion, in accordance with law, either
repair the machine using new or refurbished parts, or replace the machine with a new or refurbished machine that is equivalent to
the machine being replaced. The warranty applies only to defects in materials and workmanship under normal use and does not
extend to damage to the product or parts which result from:- alteration, repair, modification or service carried out by anyone other than an authorised ACCO service centre.
- accident, neglect, abuse or misuse owing to failure to comply with the normal operating procedures of the product.
Lamination Guide
Setting without Carrier
Material
Copy Paper
Brochure Paper
Photo Paper
Setting with Carrier
Film thickness
Temperature
Speed
Temperature
Speed
75 ~ 100 Micron
100°C
6
130°C
4
125 ~ 150 Micron
120°C
4
130°C
3
175 ~ 250 Micron
120°C
3
140°C
2
300 ~ 350 Micron
130°C
2
-
-
75 ~ 100 Micron
100°C
5
130°C
4
125 ~ 150 Micron
120°C
3
140°C
3
175 ~ 250 Micron
130°C
2
140°C
2
300 ~ 350 Micron
140°C
2
-
-
75 ~ 100 Micron
100°C
4
130°C
3
125 ~ 150 Micron
130°C
3
140°C
2
175 ~ 250 Micron
140°C
2
140°C
1
NOTE: For “STAND BY” mode, please keep the temperature at 70°C and speed 2.
Ref:PROSERIES-3600-4600/SG/V1/220415
ACCO BRANDS ASIA PTE LTD
5A Toh Guan Road East
#06-03 Singapore 608830
Tel: +65 6776 0195
Fax: +65 6779 1041
[email protected]