Name of each part

■

KIV-101 Monitor

4 inch screen

To identify visitor

Call Signal

Volume Control

Knob

To control calling signal volume.

Speaker Volume

Control Knob

To control speaker volume.

AUTO-REC

C-Mic

To communicate with camera or guardroom

Power Lamp

Communication Button

To communicate with camera or guardroom

Priority communication Button

To communicate with camera first

Camera Button

To see the visitor

Guadroom Button

To communicate with guardroom

Door Release Button

To open the door

Contrast Control Knob

To control contrast of monitor screen.

Brightness Control Knob

To control brightness of monitor screen

■

KC-C61 Camera & KC-D30 Metal Pinhole Camera

C-Mic

To communicate with Monitor

Camera Lens

Clear picture quality realized by adopting 1/3" CCD

Power Lamp

To check power ON/OFF status

Call Button

By pressing the button, the related house will be called.

Speaker

When visitor calls, the voice from monitor comes out of the speaker.

※ Option

Precautions for Operation

Keep away from humidifier and stove. High temperature and humidity can cause breakdown.

Do not drop monitor or door camera, and avoid strong impact.

Keep away from devices generating strong magnetic field

(TV, Speaker, etc.) (Picture can be disturbed or blurred and breakdown can result)

When cleaning, never use wet hands, volatile benzene or paint thinner.

Keep picture clear by cleaning camera window frequently with soft cloths.

As this device consists of electronic precision components, and high voltage is generated internally, do not attempt to disassemble.

WARNING To Reduce the risk of fire orelectric shock Do not expose this appliance to rain ormoisture

CAUTION To prevent electric shock, match wide blade of plug to wide slot, fullt insert.

Installation Precautions

Monitor and camera must be installed away from direct light and counter light.

Camera must be installed at a place free from rain.

Standard height of monitor must be 1,450mm~1,500mm from ground, centered around brawn tube.

Camera should be installed on the wall in which cement is completely dry.

If installed during winter season at temperature below

-5 �, condensation might be generated inside monitor and camera due to temperature difference between indoors and outdoors. To prevent breakdown due to such condensation, connection should be made in 2 hours or more after installation.

Do not install monitor and camera in locations subject to direct heating as harmful gases may subsequently be emitted in significant amounts.

Stop up P.V.C. pipe using adiabatic substances, to prevent air circulation

※Stopping up pipe as above minimizes temperature difference between indoors and outdoors, and also eliminates moisture and condensation on door camera window.

notice

Don’t install the set on a weak or ceiling surface such as plaster or press board, please install the set on the hard wall or ceiling like firm timber or concrete.

Component

●

Monitor & Camera

●

Camera Accessories

� Main body supporter

� Screw for fixing camera to panel (2.6x6mm)

� Screw for fixing camera main body supporter

(4x25mm)

� Upward adjusting supporter for adjusting lens angle upward

●

Monitor Accessories

� Upword adjusting

Supporter for lens angle

� Wall hanger panel

� Screws for fixing

(4x25mm)

Specifications

MONITOR

(KIV-101)

CAMERA

(KC-C61)

Metal Pinhole

Camera

(KC-D30)

Power source Power Built-in AC 120V 60Hz

Power consumption

Ambient temperature

Braun tube

Max.15W, Stand by : 1W

0 ℃ ~+50 ℃

4 inch Flat Tube (B/W)

Communication system Hands-free system

Call signal sound

Output Impedance

Wiring

Max Wiring Distance

Camera:Ding-dong, guardroom: Melody

Picture : 75ohm, Voice : 600ohm

4 Wired in polarity / guardroom Wired in non-polarity

Camera:� 0.65 Single Cable/50m Guardroom:IV 0.9mm

Power source

Ambient temperature

Angle of picture

Min. Illumination

Lens

Dimension

KC-C61 KC-D30

DC12V ± 1V(power from Monitor)

-10 ℃ ~50 ℃

Diagonal 120 。 Diagonal 90 。

0.1Lux (LED ON)

F:2.0, f=3.0mm

95(W) × 127(H) × 34(D)mm

F:3.5, f=3.8mm

95(W) × 127(H) × 33(D)mm

Video Doorphone Wiring Diagram

��

Wiring Diagram

(Option)

Caution for wiring

� Wiring between videophone and camera is 4 wire in polarity and use � 0.65mm or more single cable

� Connecting wiring between monitor and door camera should not be installed near other electrical cable, norbe horizontal.(In such case, clear picture can not be expected due to interruption by electrical noise)

Monitor Installation

When system is attached to 1 rectangular switch box

Screw

Basic Installation method of Monitor

Wall Screw

1 Rec tangular switch box

Wall hanger panel for fixing Monitor

Wall hanger panel for fixing Monitor

��

Standard height monitor

Standard height of monitor is ranged 1,450 ~ 1,500 from bottom to the center of monitor screen.

For installation, avoid the places where there is any excessive humidity,magnetic force, dangerous chemicals, direct ray of sun, and any places near a heater which can cause break down.

Center of monitor

Bottom of

1Rectangular switch box

(unit:mm)

Door camera Installation

��

Surface-mounting Door Camera Installation

Upward control groove

Straight Ahead Installation

After attach the body supporter with 2 screws(4x10mm), put the Door Camera into the grooves of body supporter, and then fix it with a screw(2.6x6mm).

Upward control groove

Looking “Upward” Installation

After attach the body supporter with 2 screws(4x10mm), insert the upward support into the upward groove of body supporter, and then fix it with a screw(2.6x6mm).

Downward control groove

Looking “ Downward ” Installation

After attach the body supporter with 2 screws(4x10mm), insert the Door Camera into the downward control groove, and then fix it with a screw(2.6x6mm).

��

DOOR CAMERA INSTALLATION

Wall

Screw(4x10mm)

Camera Front bady support

Upward support

Screw(2.6x6mm)

��

Standard Height of Door Camera

Bottom base of

One hall Box

Surface mount

Standard height of the door camera is 1,400mm �

1,450mm from the bottom of one camera to the floor.

Flush mount

In case that the height of Door camera exceeds the range of min. 1,250mm �1,550mm, it is impossible to control the screen picture with only the lens angle, and therefore, be careful of the height of camera installation.

(unit:mm)

Warranty

To receive after-Sale service, have the following ready when you contact our branches

1. Name of the product

2. Model number of the product

3. The area of problem

4. Phone number and address at which you can be contacted.

Warranty Card

PRODUCT

MODEL

DATE PURCHASED

WARRANTY PERIOD

AGENCY ADDRESS

■

KOCOM Warranties the original purchaser of this product as follows.

1) This product is produced under strict quality control and inspection procedures.

2) If this product breaks down during proper use as a result of product defect, KOCOM will repair it within one year from date of purchase free of charge.

3) The following cases will be subject to charge, even during warranty period: a. Breakdown during transport, or through careless treatment, by consumer.

b. Breakdown cause by unauthorized repair, or system modification.

c. Breakdown caused by natural disaster or power disorder.

This manual is based on the date as shown in the right and specifications are subject to change without notice for quality improvement.

KIV-101 03.04

HANDS-FREE VIDEOPHONE

KIV-101 Operating Installation Manual

Clear & Bright Picture at Low Light

■

4

″

Flat Monitor

■

4 Wired

■

Easy Installation

■

Slim Size Camera

■

Wide view angle

KC-C61 (120

。

KC-D30 (90

。

■

Hands-free System

Thank you very much for purchasing KOCOM video doorphone. please read this manual thoroughly to ensure correct usage, before operating

※ Option

KIV-101 KC-C61 Metal Pinhole Camera

KC-D30 www.kocom.co.kr e-mail:[email protected]

www.kocominc.com(us) e-mail:[email protected](us)

How to operate (Instruction for operating)

��

Call from visitor

1.When visitor presses call button of door camera, the ding-dong sound is made from monitor and visitor image appears in the screen of the monitor.

2.After checking the visitor through the screen, press communication button then you can communicate with visitor. (The screen of the monitor is automatically off after 3 minutes.)

3.When the conversation is finished with visitor, press communication or camera button, then screen is off. And you can press door release button in order to open the door automatically.

4.If you want to check the outside, press camera button then the screen is on and you can check outside. (But you cannot communicate with camera. If you want to communicate with camera, press communication button.)

※ Instruction for the priority communication button (It is only available with the communication through camera)

The function of priority communication button is to send the voice from the monitor to camera in priority.

Ex) In case the voice from monitor to camera is not heard well and clearly due to the heavy noise outside, press this priority communication button, then the visitor can hear the voice from the monitor well and clearly.

��

Communication with guardroom

1. In case the monitor is connected to the guardroom, if you press the guardroom button, the signal is made and if the person in guardroom answers, you can communicate. And after conversation with guardroom, you can press this button again stop to communication.

2.While you communicate with guardroom, if the chime sound from the camera is made the screen is on, then you can check the visitor. (The screen is on for 30 seconds and automatically off) At this time, if you press camera or communication button, the communication with guardroom is ended and you can communicate with the visitor through the camera.

3.While you communicate with the visitor through camera, if the call from guardroom is made, the melody sound is ringing. And you can communicate with guardroom by pressing guardroom or communication button after finishing the communication with visitor.

※ Note : please certainly press guardroom button after finishing the communication with guardroom.

This symbol is to be included in the Important Safeguards of applicable units adjacent to Item 9.

the product and cart combination to overturn. part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to products (including amplifiers) that produce heat.

safety checks to determine that the product is in proper operating condition.

may result in fire, electric shock, or other hazards.

parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions damage and will often require extensive work by a qualified technician to restore the product to its normal controls that are covered by the operating instructions as an improper adjustment of other controls may result in

D.If the product does not operate normally by following the operating instructions. Adjust only those

This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

CAUTION : Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or residential installation.

Class B device

C.If the product has been exposed to rain or water.

operation.

manufacturer.

24.Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the

23.Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform

22.Replacement Parts - When replacement parts are required, be sure the service technician has used replacement

25.Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other

F.When the product exhibits a distinct change in performance - this indicates a need for service.

E.If the product has been dropped or damaged in any way.

t g k antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type

This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into

Alternate Warnings - This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin.

replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable intended to operate from battery power, or other sources, refer to the operating instructions.

are not sure of the type of power supply to your home, consult your product dealer or local power company. For products installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be

A.When the power-supply cord or plug is damaged.

voltage or other hazards. Refer all servicing to qualified service personnel.

voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

where they exit from the product.

under the following conditions: of fire or electric shock.

as the original plug.

B.If liquid has been spilled, or objects have fallen into the product.

17.Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric ligh

16.Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for lon

21.Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel

20.Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous

19.Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous

18.Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a ris plug.

14.Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety

13.Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by

15.Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or adhered to.

12.Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one

11.Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you

10.Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product

CAUTION :TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT RENOVE COVER(OR

BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFED

SERVICE PERSONNEL

The lighting flashwith arrowhead sysmbol, Within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous vollage‘ with in the product ‘s enclosure that may be of sufficient magnitube arisk of electric snock to persons.

The exclarnation point with in a equilateral triangle, is intended to alert the user to the presence of important operating and maintenance(Servicing)instructions in the literature accompanying the appliance.

Safeguard

Read Instructions - All the safety and operating instructions should be read before the product is operated.

Retain Instructions - The safety and operating instructions should be retained for future reference.

Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.

Follow Instructions - All operating and use instructions should be followed.

Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.Use a

Attachments - Do not use attachments not recommended by the product manufacturer as they

Water and Moisture - Do not use this product near water°°- for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product mayfall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer.

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause damp cloth for cleaning.

may cause hazards

7.

6.

8.

5.

4.

3.

2.

1.

9.

Notice: Don’t install the set on a weak or ceiling surface such as plaster or press board, Please install the set on the hard wall or ceiling like firm timber or concrete.

CAUTION: TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT" / ATTENTION: POUR VITER LES CHOCS ELECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET

POUSSER JUSQU'AU FOND.