Schneider Electric XBTN/R/RT, Compact Display Units User manual

Magelis XBT N/R/RT
33003962 11/2011
Magelis XBT N/R/RT
Compact Display Units
User Manual
33003962.03
11/2011
www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or
technical characteristics of the performance of the products contained herein. This
documentation is not intended as a substitute for and is not to be used for
determining suitability or reliability of these products for specific user applications. It
is the duty of any such user or integrator to perform the appropriate and complete
risk analysis, evaluation and testing of the products with respect to the relevant
specific application or use thereof. Neither Schneider Electric nor any of its affiliates
or subsidiaries shall be responsible or liable for misuse of the information contained
herein. If you have any suggestions for improvements or amendments or have found
errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic
or mechanical, including photocopying, without express written permission of
Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when
installing and using this product. For reasons of safety and to help ensure
compliance with documented system data, only the manufacturer should perform
repairs to components.
When devices are used for applications with technical safety requirements, the
relevant instructions must be followed.
Failure to use Schneider Electric software or approved software with our hardware
products may result in injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
© 2011 Schneider Electric. All rights reserved.
2
33003962 11/2011
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . .
General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standards and General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3 Characteristics of the XBT Terminal Range. . . . . . . . . .
3.1 Characteristics of the XBT Terminal Range . . . . . . . . . . . . . . . . . . . . . . .
Characteristics Applying to All XBT Terminals . . . . . . . . . . . . . . . . . . . . .
Characteristics of the Individual XBT Terminals . . . . . . . . . . . . . . . . . . . .
Polling Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4 Operating Elements, LEDs and Connectors . . . . . . . . .
4.1 Operating Elements, LEDs and Connectors . . . . . . . . . . . . . . . . . . . . . . .
Front Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview of Keys on the Individual XBT Terminals . . . . . . . . . . . . . . . . .
Chapter 5 Insert Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 Insert Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insert Labels XBT N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insert Labels XBT R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insert Labels XBT RT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6 Inserting Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inserting Insert Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 7 Creating Individual Labels . . . . . . . . . . . . . . . . . . . . . . . .
Creating Individual Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 8 Connecting XBT Terminals . . . . . . . . . . . . . . . . . . . . . . .
8.1 Grounding and Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information Concerning the Grounding of Terminals . . . . . . . . . . .
33003962 11/2011
7
9
11
11
13
13
17
17
18
19
25
27
27
28
32
34
41
41
42
44
46
49
49
53
53
57
58
58
3
8.2 Connecting XBT Terminals to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distinguishing XBT Terminals by Power Supply . . . . . . . . . . . . . . . . . . .
Connecting XBT Terminals Powered by the PLC to a PC . . . . . . . . . . . .
Connecting XBT Terminals Powered by an External Power Supply to a
PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3 Connecting XBT Terminals to a PLC . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distinguishing XBT Terminals by Power Supply . . . . . . . . . . . . . . . . . . .
Connecting XBT Terminals Powered by the PLC to a PLC . . . . . . . . . . .
Connecting XBT Terminals Powered by an External Power Supply to a
PLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4 Connecting XBT N401 / R411 / RT511 Terminals to a Printer . . . . . . . .
Printer Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
68
69
71
Chapter 9 Overview of Applications and Functions . . . . . . . . . . . .
81
9.1 Overview of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview of XBT Terminal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2 XBT Terminals in HMI Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HMI Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.3 Functions of Keys, Touchscreen, LEDs. . . . . . . . . . . . . . . . . . . . . . . . . .
Functions of Keys and Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functions of LEDs on XBT N401 / XBT R411 / XBT RT511 Terminals. .
82
82
83
83
86
87
90
Chapter 10 Operating Principles of XBT Terminals . . . . . . . . . . . . . .
91
10.1
10.2
10.3
10.4
4
Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Selection of the Mode of Operation . . . . . . . . . . . . . . . . . . . .
Transfer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel Structure of XBT Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Principle of Application Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Application Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Principle of Alarm Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Principle of System Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying System Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scrolling within Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing Configuration Parameters via the System Panel SYSTEM . .
Selecting the HMI Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the Date and Time Format . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing the Product Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing the Line Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Password-Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing Password-Protected Panels, Fields, Functional Links . . . . . .
60
61
62
75
80
80
92
93
94
95
97
99
100
101
105
106
109
110
111
113
114
115
116
117
118
119
119
33003962 11/2011
Chapter 11 Communication Between XBT Terminals and the
Automation System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1 Types of Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Impulse Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toggle Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2 Activating Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating Commands via Functional Links, Button Objects or Dynamic
Function Keys on the Display Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating Commands via Function Keys on the Display Unit. . . . . . . . . .
11.3 Entering / Modifying Values Alphanumeric Fields in Edition Mode . . . . . .
Accessing an Alphanumeric Edition Field . . . . . . . . . . . . . . . . . . . . . . . . .
Entering a Value in an Edition Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirming / Cancelling an Edition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exit Edition on Time Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Edition Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4 Handling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing or Ignoring Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.5 Printing Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Principles of Printing Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Alarms as a Data Stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing the Alarm Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 12 Vijeo-Designer Lite Configuration Software . . . . . . . . .
121
122
123
124
125
126
131
132
133
135
137
138
139
140
141
143
144
145
146
147
149
Creating XBT Terminal Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exchanging Data with the Automation System via the Dialog Table. . . . .
150
151
Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
153
Appendix A Troubleshooting and Further Information . . . . . . . . . . .
155
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Self-Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix B Architectures of Automation Systems . . . . . . . . . . . . . .
156
158
160
162
163
Types of Architectures of Automation Systems. . . . . . . . . . . . . . . . . . . . .
163
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
167
179
33003962 11/2011
5
6
33003962 11/2011
Safety Information
§
Important Information
NOTICE
Read these instructions carefully, and look at the equipment to become familiar with
the device before trying to install, operate, or maintain it. The following special
messages may appear throughout this documentation or on the equipment to warn
of potential hazards or to call attention to information that clarifies or simplifies a
procedure.
33003962 11/2011
7
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by
qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the construction
and operation of electrical equipment and its installation, and has received safety
training to recognize and avoid the hazards involved.
8
33003962 11/2011
About the Book
At a Glance
Document Scope
This manual describes how to use the Magelis XBT N/R/RT device.
Validity Note
The technical characteristics of the device(s) described in this manual also appear
online. To access this information online:
Step
Action
1
Go to the Schneider Electric home page www.schneider-electric.com.
2
In the Search box type the model number of a product or the name of a product
range.
z Do not include blank spaces in the model number/product range.
z To get information on a grouping similar modules, use asterisks (*).
3
If you entered a model number, go to the Product datasheets search results
and click on the model number that interests you.
If you entered the name of a product range, go to the Product Ranges search
results and click on the product range that interests you.
4
If more than one model number appears in the Products search results, click on
the model number that interests you.
5
Depending on the size of your screen, you may need to scroll down to see the
data sheet.
6
To save or print a data sheet as a .pdf file, click Download XXX product
datasheet.
The characteristics presented in this manual should be the same as those that
appear online. In line with our policy of constant improvement we may revise content
over time to improve clarity and accuracy. In the event that you see a difference
between the manual and online information, use the online information as your
reference.
33003962 11/2011
9
The present documentation is intended for qualified technical personnel responsible
for the implementation, operation and maintenance of the products described. It
contains information necessary for the proper use of the products. However, those
who wish to make a more "advanced" use of our products may find it necessary to
consult our nearest distributor in order to obtain additional information.
Registered Trademarks
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Related Documents
Title of Documentation
Reference Number
Vijeo-Designer Lite Online Help
33003968
Modbus Master Protocol XBT N/R/RT
33003986
Modbus SlaveProtocol XBT N/R/RT
33003980
Uni-Telway Protocol XBT N/R/RT
33003974
Siemens PPI Protocol XBT N/R/RT
33003992
AB DF1 Protocol XBT N/R/RT
33003998
AB DH485 Protocol XBT N/R/RT
33004016
Mitsubishi FX Protocol XBT N/R/RT
33004004
SYSMAC-WAY Protocol XBT N/R/RT
33004010
Zelio Protocol XBT N/R/RT
EIO0000000226
Millenium Protocol XBT N/R/RT
EIO0000000257
You can download these technical publications and other technical information from
our website at www.schneider-electric.com.
User Comments
We welcome your comments about this document. You can reach us by e-mail at
[email protected].
10
33003962 11/2011
Magelis XBT N/R/RT
Document Conventions
33003962 11/2011
Document Conventions
1
General information
Pictograms
The meaning of the pictograms used in this document is explained below.
Pictogram
Description
Indicates information concerning the communication LED.
Indicates information concerning LEDs in general.
Represents a button on the Vijeo-Designer Lite program toolbar.
Represents a button on the XBT terminal.
33003962 11/2011
11
Document Conventions
12
33003962 11/2011
Magelis XBT N/R/RT
Overview
33003962 11/2011
Overview
2
Standards and General Safety Precautions
List of Standards
XBT terminals have been developed to conform to the following standards:
z
z
z
33003962 11/2011
UL 508 for Industrial Control Equipment
UL 1604 Electrical Equipment for Use in Class I and Class II Division 2 and
Class III Hazardous Locations
CAN/CSA-C22.2, No. 14, No. 213, and No. 60950 Industrial Control Equipment
Miscellaneous Apparatus - For Hazardous Locations.
13
Overview
General Safety Precautions
DANGER
EXPLOSION
z
z
z
z
z
z
z
Compatibility: Power and external device wiring must be in accordance with
Class I, Division 2 wiring methods - Article 501- 4(b) of the National Electrical
Code, Groups A, B, C and D Hazardous Locations or Non-Hazardous
Locations, NFPA 70 or as specified in section 18-152 of the Canadian Electrical
Code for installations within Canada and in accordance with the authority
having jurisdiction.
Do not perform substitution of components that may impair compliance to Class
I, Division 2.
Confirm that the location is not subject to any risk of explosion before
connecting or disconnecting equipment, replacing or wiring modules.
Confirm that the power supply has been turned OFF before disconnecting,
replacing or wiring modules.
Before turning ON, sweep front panel with a damp cloth to discharge
electrostatics.
Do not use apparatus that has been damaged.
When used in hazardous locations (Class I Div.2, UL and CSA) and if suitable
for the application (see product label) do not connect or disconnect equipment
unless power has been switched off or the area is known to be non-hazardous.
Failure to follow these instructions will result in death or serious injury.
WARNING
LOSS OF CONTROL
Due to the risk that a value entered on the terminal may not reach the equipment
(for example, if a communication break occurs due to huge bandwidth
consumption, the value may not be sent to the PLC) you are not allowed to use the
terminal to pilot safety critical processes, for example emergency stop or crane
load manipulation where human beings may get injured.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
14
33003962 11/2011
Overview
WARNING
UNINTENDED EQUIPMENT OPERATION
z
z
Read and follow all user instructions and documentation.
Follow all local and national product safety codes and standards.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
33003962 11/2011
15
Overview
16
33003962 11/2011
Magelis XBT N/R/RT
Characteristics of the XBT Terminal Range
33003962 11/2011
Characteristics of the XBT
Terminal Range
3.1
3
Characteristics of the XBT Terminal Range
Overview
This section lists the characteristics of the individual versions of the XBT terminal
range.
What’s in this Section?
This section contains the following topics:
Topic
33003962 11/2011
Page
Characteristics Applying to All XBT Terminals
18
Characteristics of the Individual XBT Terminals
19
Polling Times
25
17
Characteristics of the XBT Terminal Range
Characteristics Applying to All XBT Terminals
Overview
XBT Type
XBT N200
XBT N400 / XBT R400 / XBT N410 / XBT N401 /
XBT RT500 /
XBT NU400 / XBT R410
XBT RT511
/ XBT R411
Environment
Compliance with standards
IEC 61131-2, IEC 60068-2-6, IEC 60068-2-27, UL 508, CSA C22-2 no. 14,
no 213, and no. 60950
Product certification
CE, UL, CSA, Class 1 Div 2 T5 (UL and CSA)
Temperature
Operation
0...+55° C (32° F...131° F)
Storage
-20...+60° C (-4° F...140° F)
Humidity (without condensation)
0...85%
Protection
IP 65 - (IEC 60529 - NF C 20010)
XBT RT: UL Type 4, indoor use only. Do not store or operate the LCD display
in areas receiving direct sunlight since the sun’s UV rays may cause the LCD
display’s quality to deteriorate.
XBT N/R: UL Type 4, 4X outdoor use (only for support ≥ 1.5 mm / 0.059 in.)
Front panel
Rear panel
ESD withstand
IP 20 (IEC 60529)
IEC 61000 - 4 - 2, level 3
Electromagnetic interference
IEC 61000 - 4 - 3, 10 V/m
Electrical interference
IEC 61000 - 4 - 4, level 3
Impact
IEC 60068 - 2 - 27; 1/2 sinusoidal pulse for 11 ms, 15 g on 3 axes
Vibration
IEC 60068 - 2 - 6 and marine certifications
± 3.5 mm 2 Hz...8.45 Hz
1 g 8.75 Hz...150 Hz
XBT RT does not have marine certifications
Mechanical characteristics
Mounting and fixing
Flush-mounted, fixed by 2 (for XBT N) or 4 (for XBT R and XBT RT) spring
clips supplied pressure-mounted for panels 1.5...6 mm (0.06...0.23 in.) thick
Material
display unit
protection
Polyester
Front frame
Polycarbonate/polybutylene terephthalate alloy
Keypad
UV autotex polyester
18
33003962 11/2011
Characteristics of the XBT Terminal Range
Characteristics of the Individual XBT Terminals
Overview
The following tables list the characteristics of the individual XBT terminal versions.
XBT Type
XBT N200
XBT N400 / XBT R400 / XBT N410 / XBT N401 /
XBT RT500
XBT NU400 / XBT R410
/ XBT R411/ XBT RT511
Electrical characteristics
Power supply
Voltage
5 VDC supplied by the PLC. For the specific
cables see Connecting XBT Terminals
(see page 57).
24 VDC (200 mA max)
Voltage limits
5 V ± 5% DC, 1 W maximum
18...30 VDC, 5 W
maximum
Ripple factor
5% maximum
NOTE: For products with a resettable fuse (XBT N410 / XBT N401 / XBT NU400 /
XBT R410 / XBT R411 / XBT RT511), switch off the power supply for 5 seconds
before resetting the fuse.
CAUTION
OVERVOLTAGE DAMAGE TO EQUIPMENT
Make sure to connect the following terminals only to a source providing 5 VDC.
z XBT N200
z XBT N400
z XBT R400
z XBT RT500
Failure to follow these instructions can result in injury or equipment damage.
NOTE: XBT RT500 terminals are protected against accidental connection to higher
voltages (up to 30 V) but the other terminal types are not and will be damaged.
XBT Type
XBT N200
XBT N400 / XBT N410 / XBT RT500 /
XBT N401 / XBT NU400 XBT RT511
/ XBT R400 / XBT R410
/ XBT R411
Operating characteristics
Display unit
33003962 11/2011
Type
Backlit LCD
Capacity
2 x 20 characters
4 x 20 characters
10 x 33 characters
19
Characteristics of the XBT Terminal Range
XBT Type
XBT N200 / XBT N400 / XBT N410 /
XBT NU400 / XBT R400 / XBT R410 /
XBT RT500
XBT N401
XBT RT511
XBT R411
Signaling
No LEDs
6 LEDs
13 LEDs
14 LEDs
XBT Type
XBT N200 / XBT N400 / XBT N410 /
XBT NU400 / XBT R400 / XBT R410 /
XBT RT500 / XBT N401 / XBT R411
XBT RT511
Buzzer
No buzzer
Buzzer for alarm signaling and
feedback on keypad/touchpad
activity
XBT Type
XBT N200 / XBT N400
XBT N401/ XBT N410 /
XBT NU400 / XBT R400 /
XBT R410 / XBT R411 /
XBT RT500 / XBT RT511
Dialog application No. of panels
128
200
Transmission medium
(asynchronous serial link)
RS232C / RS485
XBT Type
XBT NU400
XBT N200 / XBT N400 /
XBT R400
XBT N401 / XBT N410 /
XBT R410 / XBT R411 /
XBT RT500 /
XBT RT511
Supported protocols
Modbus master, Zelio,
Millenium
Modbus master, UniTelway
Modbus master and
slave(*), Uni-Telway,
Siemens PPI, AB DF1,
AB DH485,
Mitsubishi FX,
SYSMAC-WAY, Zelio
(**), Millenium (**)
Real-time clock
Access to the PLC real-time clock
(*) Modbus slave is not supported by the XBT RT500.
(**) Zelio is supported only by the XBT N401, XBT R411 and XBT RT511.
(**) Millenium is supported only by the XBT N401, XBT R411 and XBT RT511.
20
33003962 11/2011
Characteristics of the XBT Terminal Range
XBT Type
Connection
Power supply
XBT N200 / XBT N400 / XBT R400 /
XBT RT500
XBT N401 / XBT N410 /
XBT NU400 / XBT R410 /
XBT R411 / XBT RT511
Via the PLC link cable or via an external
5 V power supply by using the
XBT ZRTPW accessory
Removable terminal block
3 screw terminals (pitch 5.08)
Clamping capacity: 1.5 mm2
(0.0023 in2)
XBT Type
Connection
XBT N200 / XBT N400 / XBT R400 /
XBT RT500 / XBT RT511
Serial link
RJ45 female connector (RS232C/RS485) 25-pin female SubD connector
(RS232C / RS485)
XBT Type
Connection
Display Units
Printer link
XBT N401 / XBT N410 /
XBT NU400 / XBT R410 /
XBT R411
XBT N200 / XBT N400 / XBT N410 /
XBT NU400 / XBT R400 / XBT R410 /
XBT RT500
XBT N401 / XBT R411 /
XBT RT511
No printer link
MiniDin (full RS232C, including
modem signals)
Alphanumeric
Display Unit
XBT N200
Matrix Display Unit
Matrix Display Unit
Matrix Display Unit
XBT N400
XBT NU400
XBT N401
Type
Backlit LCD
Backlit LCD 122 x 32 pixels
Color
Green
Capacity
2 lines of 20
characters
Display
Green/Orange/Red
1...4 lines of 5...20 characters
Active display unit
74 x 12 mm (2.91 x
area (width x height) 0.47 in.)
72 x 20 mm (2.83 x 0.79 in.)
Size of characters
(width x height)
3.2 x 5.5 mm (0.13 x
0.22 in.
2.9 x 4.3 to 11.8 x 17.4 mm (0.11 x 0.17 to 0.46 x 0.69 in.)
Keypad
8 keys, 4 of them can be re-labeled
Signaling
No LEDs
33003962 11/2011
6 LEDs including 4 for
the 4 central keys
21
Characteristics of the XBT Terminal Range
Alphanumeric
Display Unit
XBT N200
Matrix Display Unit
Matrix Display Unit
Matrix Display Unit
XBT N400
XBT NU400
XBT N401
Number of panels
(maximum)
128 application
panels
200 application panels
256 alarm panels
Variables per panel
8
40
Vertical panel
scrolling
no
yes
Number of lines per
panel
2
25
Representation of
variables
Alphanumeric
Fonts
Latin + Katakana
Languages
Number of languages only limited by the size of the memory
Display Units
Functions
Latin + Cyrillic + Katakana + Greek + Simplified Chinese
Communication
Serial link
RS232 C, RS485
Protocols
Modbus master, Uni-Telway
Programming
software
Vijeo-Designer Lite (using Windows XP or Vista)
Matrix Display Units XBT N410
XBT R400
Modbus master
XBT R410
Modbus master and
slave, Uni-Telway,
Siemens PPI,
AB DF1, AB DH485,
Mitsubishi FX,
SYSMAC-WAY,
Zelio, Millenium
XBT R411
Display
Type
22
Backlit LCD 122 x 32 pixels
33003962 11/2011
Characteristics of the XBT Terminal Range
Matrix Display Units XBT N410
XBT R400
Color
Green
Capacity
1...4 lines of 5...20 characters
XBT R410
XBT R411
Green/Orange/Red
Active display unit
72 x 20 mm (2.83 x 0.79 in.)
area (width x height)
Size of characters
(width x height)
2.9 x 4.3 to 11.8 x 17.4 mm (0.11 x 0.17 to 0.46 x 0.69 in.)
Keypad
8 keys, 4 of which can 20 keys, 12 of which can be re-labeled
be re-labeled
Signaling
No LEDs
16 LEDs including 14
for the central keys
Functions
Number of panels
(maximum)
200 application panels
256 alarm panels
Variables per panel
40
Vertical panel
scrolling
yes
Number of lines per
panel
25
Representation of
variables
Alphanumeric
Fonts
Latin + Cyrillic + Katakana + Greek + Simplified Chinese
Languages
Number of languages only limited by the size of the memory
Communication
Serial link
RS232 C, RS485
Protocols
Modbus master and
slave, Uni-Telway,
Siemens PPI,
AB DF1, AB DH485,
Mitsubishi FX,
SYSMAC-WAY
Programming
software
Vijeo-Designer Lite (using Windows XP or Vista)
33003962 11/2011
Modbus master, UniTelway
Modbus master and
slave, Uni-Telway,
Siemens PPI,
AB DF1, AB DH485,
Mitsubishi FX,
SYSMAC-WAY
Modbus master and
slave, Uni-Telway,
Siemens PPI,
AB DF1, AB DH485,
Mitsubishi FX,
SYSMAC-WAY,
Zelio, Millenium
23
Characteristics of the XBT Terminal Range
Matrix Display Units XBT RT500
XBT RT511
Display
Type
Backlit LCD 198 x 80 pixels
Color
Green
Capacity
2...10 lines of 5...33 characters
Green/Orange/Red
Active display unit
89.9 x 40 mm (3.54 x 1.57 in.)
area (width x height)
Size of characters
(width x height)
2.7 x 4 to 16 x 16 mm (0.11 x 0.16 to 0.43 x 0.94 in.)
Keypad
12 keys: in control and input variant 4 of them can be re-labeled, in touch variant 10 of them
can be re-labeled
Signaling
No LEDs
13 LEDs including 10 for the central keys
Functions
Number of panels
(maximum)
200 application panels
256 alarm panels
Variables per panel
40
Vertical panel
scrolling
no
Number of lines per
panel
10
Representation of
variables
Alphanumeric semi-graphical (bargraph, trends, lights and buttons)
Fonts
Latin + Cyrillic + Katakana + Greek + Simplified Chinese
Languages
Number of languages only limited by the size of the memory
Communication
Serial link
RS232 C, RS485
Protocols
Modbus master , Uni-Telway, Siemens PPI,
AB DF1, AB DH485, Mitsubishi FX,
SYSMAC-WAY
Programming
software
Vijeo-Designer Lite (using Windows XP or Vista)
24
Modbus master and slave, Uni-Telway,
Siemens PPI, AB DF1, AB DH485,
Mitsubishi FX, SYSMAC-WAY, Zelio,
Millenium
33003962 11/2011
Characteristics of the XBT Terminal Range
Polling Times
Overview
The polling times for non-connected equipment differ between XBT N/R/RT
terminals and XBT NU400 terminals. The following sections describe general polling
times of XBT N/R/RT terminals and specific polling times of XBT NU400 terminals.
General Polling Time for Non-Connected Equipment
The XBT N/R/RT terminal polls the missing equipment (usually a PLC) every 5
seconds. All the configured PLCs in an application should be connected. A missing
equipment is therefore considered to be a temporary problem, i.e. the PLC or XBT
is temporarily disconnected, and communication will resume as soon as the
connection is re-established. In this arrangement, degraded communication
performance is considered acceptable.
33003962 11/2011
25
Characteristics of the XBT Terminal Range
Polling Time of XBT NU400 Terminals
The XBT NU400 polls the missing equipment, i.e. a starter, every 5 minutes. This
time interval has been selected due to performance and system validation reasons.
The XBT NU400 is delivered with a unique pre-loaded application for
communication with up to 8 TESYS model U starters. However, in the final system
configuration, less than 8 starters may be used permanently as a normal installation.
In this case, polling the missing starter(s) in too short time intervals will drastically
decrease the communication with the connected starters. This, in turn, may lead to
increased response times and cause critical application issues. In some cases, time
between operator action and starter acknowledgement can be longer than 20
seconds.
This is why the polling time of non-connected equipment has been set to this much
longer period of 5 minutes.
The pre-loaded application in XBTNU400 in version 2.2 and later provide a page for
manually resetting the communication. During this manual restart of the terminal the
reconnected devices will be detected.
26
33003962 11/2011
Magelis XBT N/R/RT
Operating Elements, LEDs and Connectors
33003962 11/2011
Operating Elements, LEDs and
Connectors
4.1
4
Operating Elements, LEDs and Connectors
Overview
This section describes all operating elements, LEDs and connectors provided on the
front and rear panels of the XBT N/R/RT terminals.
What’s in this Section?
This section contains the following topics:
Topic
33003962 11/2011
Page
Front Panels
28
Rear Panels
32
Overview of Keys on the Individual XBT Terminals
34
27
Operating Elements, LEDs and Connectors
Front Panels
Overview
The following sections list the front panels of the individual XBT terminal versions
with the operating and control elements.
XBT N Terminals
On their front panels the XBT N terminals provide the following operating and
control elements:
XBT N200
XBT N401
XBT N••
28
33003962 11/2011
Operating Elements, LEDs and Connectors
33003962 11/2011
No.
Description
1
Backlit LCD display
2
Communication LED (XBT N401)
3
Alarm LED (XBT N401)
4
LEDs that can be controlled by the PLC (XBT N401)
5
Service keys for functional link
6
Service keys
7
Keys for function or numeric input (according to software configuration)
29
Operating Elements, LEDs and Connectors
XBT R Terminals
On their front panels the XBT R terminals provide the following operating and control
elements:
XBT R4••
XBT R411
30
XBT R4••
No.
Description
1
Backlit LCD display
2
Communication LED (XBT R411)
3
Alarm LED (XBT R411)
4
LEDs that can be controlled by the PLC (XBT R411)
5
Service keys for functional link
33003962 11/2011
Operating Elements, LEDs and Connectors
No.
Description
6
Service keys
7
Control keys for function or digital input (according to the context)
XBT RT Terminals
On their front panels the XBT RT terminals provide the following operating and
control elements:
XBT RT5••
33003962 11/2011
No.
Description
1
Backlit LCD display
XBT RT511
2
Service keys
3
Keys for control or service (according to software configuration)
4
Configurable touchscreen
5
Communication LED (XBT RT511)
6
Alarm LED (XBT RT511)
7
LEDs that can be controlled by the PLC (XBT RT511)
8
Touch LED (XBT RT511)
31
Operating Elements, LEDs and Connectors
Rear Panels
Overview
The following section shows the different rear panels of the individual XBT terminal
versions with their connectors.
Rear Panel
On their rear panels the XBT terminals provide the following connectors
XBT N200 / XBT N400 / XBT R400
XBT N410 / XBT NU400 / XBT R410
XBT N401 / XBT R411
XBT RT500
XBT RT511
32
No.
Description
1
RJ45: serial link + PLC power supply
2
RJ45 serial link
3
SubD25 serial link
33003962 11/2011
Operating Elements, LEDs and Connectors
33003962 11/2011
No.
Description
4
3-wire terminal for 24 VDC power supply
5
MiniDIN connector for printer
33
Operating Elements, LEDs and Connectors
Overview of Keys on the Individual XBT Terminals
Overview
The various types of XBT terminals provide different front panels including different
keys for executing functions or entering values . The following paragraphs provide
an overview of the keys provided on the individual XBT terminals.
WARNING
UNINTENDED EQUIPMENT OPERATION
The control key insert label must match the configured function of the key.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
Types of Keys
The front panels of the terminals include 2 types of keys:
z
z
Service keys
Service keys provide different actions to the operator, like scrolling within the
display of the terminal, selecting the panel to be displayed as well as selecting
objects or entering values in the panel shown on the terminal display.
Function keys
Function keys are individually configured by the HMI designer who created the
HMI application of the XBT terminal using the Vijeo-Designer Lite software. 2
different types of function keys are available:
z static function keys: Static function keys are assigned a constant function (like
selecting the panel to be displayed or executing commands) for the entire HMI
application.
z dynamic function keys: Dynamic function keys can be assigned different
functions (like selecting the panel to be displayed, setting/resetting bits or
executing commands) by the HMI designer, depending on the actually
displayed panel.
XBT N and XBT RT terminals can be configured for different variants (control and
input variant as well as touch variant only for XBT RT) with the function keys
providing different functions in each variant. XBT R terminals, on the other hand,
only provide one variant.
It is also possible that function keys have different functions in one variant,
depending on whether you are only viewing the panels (normal mode) or you are
entering values (edition mode). Function keys with 2 functions are referred to as
dual labelled keys in this manual.
34
33003962 11/2011
Operating Elements, LEDs and Connectors
Overview of Keys on the Terminals
The individual terminals provide the following keys:
XBT N
XBT R
XBT RT
12 customizable function
4 customizable keys which
can be configured as function keys
keys (control variant) or as
service keys (input variant)
2 non-configurable service
keys
z 2 non-configurable service
2 configurable service keys
for functional link keys
2 configurable service keys
for functional link keys
10 customizable keys which
can be configured as 10
function keys (touch variant)
or as 4 function and 6 service
keys (control or input
variants)
2 non-configurable service
keys
keys
z 4 non-configurable service
keys
configurable touchscreen
Keys on XBT N Terminals
XBT N terminals are customized for 2 different variants:
z
z
control variant
input variant
In these 2 different variants the terminals provide the following keys on their front
panels:
Control variant
33003962 11/2011
Input variant
35
Operating Elements, LEDs and Connectors
No.
Element
Description
1
Static function
keys
z access to a panel
z impulse command
z toggle command
2a
Left/right
arrows in
control variant
(functional link
keys)
Command link keys:
z impulse command
z toggle command
z variable write operation
Left/right
arrows in input
variant
(functional link
keys)
Navigation link keys:
Command link keys:
z change panel in a menu
z display current alarms
z change digit in a variable field
z impulse command
z toggle command
z variable write operation
3
ESC
Cancel an entry or an action
4
DEL
Clear the selected digit or field
5
Up/down
arrows
Go up, go down in a panel
(XBT N40• and NU400)
Increment/decrement the
selected digit
Select a value in a selection list
Increment/decrement the value
of a variable field
6
MOD
Select a field
Go to the next field
7
ENTER
Confirm a selection or an entry
Acknowledge an alarm
2b
36
Navigation link keys:
z change panel in a menu
z display current alarms
during edition
Return to the previous panel
33003962 11/2011
Operating Elements, LEDs and Connectors
Keys on XBT R Terminals
33003962 11/2011
No.
Element
Description
1
Dual labelled
keys
(function/nume
ric)
z
z
z
z
2
Left/right
arrows
(functional link
keys)
Navigation link keys:
z change panel in a menu
z display current alarms
z change digit in a variable field
during edition
z impulse command
z toggle command
z variable write operation
3
ESC
Cancel an entry or an action
Return to the previous panel
4
DEL
Clear the selected digit or field
5
Up/down
arrows
Go up, go down within a panel;
Increment/decrement the
selected digit
6
MOD
Select a field
Go to the next field
7
ENTER
Confirm a selection or an entry
Acknowledge an alarm
access to a panel
impulse command
toggle command
modification of a value
Command link keys:
Select a value in a selection list;
Increment/decrement the value of
a variable field
37
Operating Elements, LEDs and Connectors
Keys on XBT RT Terminals
Control variant
Input variant
Touch variant
38
33003962 11/2011
Operating Elements, LEDs and Connectors
33003962 11/2011
No.
Element
Description
1
Left/right
arrows
(functional link
keys)
Navigation link keys:
z navigation: change panel in a
menu
z display current alarms
z change digit in a variable field
during edition
2
Up/down
arrows
Select a functional link in a panel Select a value in a selection list
Increment/decrement the value of
Increment/decrement the
a variable field
selected digit
3
ESC
Cancel an entry or an action
4
DEL
Clear the selected digit or field
5
MOD
Select a field
Go to the next field
6
ENTER
Confirm a selection or an
entered value
Acknowledge an alarm
7a
Control or
touch variant
Static function keys:
z access a panel
z impulse command
z toggle command
7b
Input variant
Dynamic function keys
(functionality is paneldependent):
z access a panel
z set / reset bit
z impulse command
z toggle command
8
Touchscreen
Activity depending on the
selected variant:
z enabled in touch variant
z disabled in control and input
variant
9
Dual labelled
keys
The active function of keys F1 to
F4 is determined by the selected
terminal mode:
z in edition mode: arrow keys
acting like up/down/left/right
arrows
z in normal mode: static
function keys (see
description 7)
Command link keys:
z impulse command
z toggle command
z variable write operation
Return to the previous panel
39
Operating Elements, LEDs and Connectors
40
33003962 11/2011
Magelis XBT N/R/RT
Insert Labels
33003962 11/2011
Insert Labels
5
5.1
Insert Labels
Overview
This section describes the different insert labels provided for the different XBT types.
What’s in this Section?
This section contains the following topics:
Topic
Insert Labels XBT N
33003962 11/2011
Page
42
Insert Labels XBT R
44
Insert Labels XBT RT
46
41
Insert Labels
Insert Labels XBT N
Overview
XBT N terminals are delivered with an insert label sheet providing the following label
types to assign different texts or symbols to the keys:
z
z
z
service key labels
function key labels
blank labels
All labels are pre-cut and just have to be pressed out of the label sheet.
The ready-to-use service key and function key labels can directly be inserted into
the XBT N terminal as described in section Inserting Insert Labels, page 49.
To print your own text or symbols on the blank labels, use the Vijeo-Designer Lite
configuration software.
New label sheets can be ordered at Schneider with the following part numbers:
XBT Terminal
Label Sheet Part Number
XBT N200 / XBT N400 / XBT NU400 / XBT N410
XBLYN00
XBT N401
XBLYN01
WARNING
UNINTENDED EQUIPMENT OPERATION
Make sure that the text/symbols on your insert label always correspond to what is
configured for your XBT terminal in the Vijeo-Designer Lite configuration software.
Otherwise the keys of your terminal will not initiate the actions indicated on them.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
Service Key Labels for XBT N Terminals
If you have configured your XBT N terminal for input variant in the Vijeo-Designer
Lite configuration software, insert the following service key label into your XBT N
terminal.
Service key label XBT N
Service key label XBT N401 (with LEDs)
42
33003962 11/2011
Insert Labels
Function Key Labels for XBT N Terminals
If you have configured your XBT N terminal for control variant in the Vijeo-Designer
Lite configuration software, insert the following function key label into your XBT N
terminal.
Function key label XBT N
Function key label XBT N401 (with LEDs)
Blank Labels for XBT N Terminals
The insert label sheet includes blank labels providing you the possibility to create
labels with your own texts or symbols.
Blank label XBT N
Blank label XBT N401 (with LEDs)
For a detailed description on how to print your own labels see Creating Individual
Labels, page 53
33003962 11/2011
43
Insert Labels
Insert Labels XBT R
Overview
XBT R terminals are delivered with an insert label sheet providing the following label
types to assign different texts or symbols to the keys:
z
z
function key labels
blank labels
All labels are pre-cut and just have to be pressed out of the label sheet.
The ready-to-use function key labels can directly be inserted into the XBT R terminal
as described in section Inserting Insert Labels, page 49.
To print your own text or symbols on the blank labels, use the Vijeo-Designer Lite
configuration software.
New label sheets can be ordered at Schneider with the following part numbers:
XBT Terminal
Label Sheet Part Number
XBT R400 / XBT R410
XBLYR00
XBT R411
XBLYR01
WARNING
UNINTENDED EQUIPMENT OPERATION
Make sure that the text/symbols on your insert label always correspond to what is
configured for your XBT terminal in the Vijeo-Designer Lite configuration software.
Otherwise the keys of your terminal will not initiate the actions indicated on them.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
Function Key Labels for XBT R Terminals
The following function key label is provided on the label sheet of XBT R terminals.
Function key label XBT R
Function key label XBT R411 (with LEDs)
44
33003962 11/2011
Insert Labels
Blank Labels for XBT R Terminals
The insert label sheet includes blank labels providing you the possibility to create
labels with your own texts or symbols.
Blank label XBT R
Blank label XBT R411 (with LEDs)
For a detailed description on how to print your own labels see Creating Individual
Labels, page 53
33003962 11/2011
45
Insert Labels
Insert Labels XBT RT
Overview
XBT RT terminals are delivered with 2 insert label sheets providing the following
label types to assign different texts or symbols to the keys:
z
z
z
z
service key labels
function key labels
touch key labels
blank labels
All labels are pre-cut and just have to be pressed out of the label sheet.
The ready-to-use service key, function key and touch key labels can directly be
inserted into the XBT RT terminal as described in section Inserting Insert Labels,
page 49.
To print your own text or symbols on the blank labels, use the Vijeo-Designer Lite
configuration software.
New label sheets can be ordered at Schneider with the following part numbers:
XBT Terminal
Label Sheet Part Number
XBT RT500
XBLYRT00
XBT RT511
XBLYRT01
WARNING
UNINTENDED EQUIPMENT OPERATION
Make sure that the text/symbols on your insert label always correspond to what is
configured for your XBT terminal in the Vijeo-Designer Lite configuration software.
Otherwise the keys of your terminal will not initiate the actions indicated on them.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
46
33003962 11/2011
Insert Labels
Service Key Labels for XBT RT Terminals
If you have configured your XBT RT terminal for input variant in the Vijeo-Designer
Lite configuration software, insert the following service key label into your XBT RT
terminal.
Service key label XBT RT
Function Key Labels for XBT RT Terminals
If you have configured your XBT RT terminal for control variant in the Vijeo-Designer
Lite configuration software, insert the following function key label into your XBT RT
terminal.
Function key label XBT RT
Touch Key Labels for XBT RT Terminals
If you have configured your XBT RT terminal for touch variant in the Vijeo-Designer
Lite configuration software, insert the following touch key label into your XBT RT
terminal.
Touch key label XBT RT
33003962 11/2011
47
Insert Labels
Blank Labels for XBT RT Terminals
The insert label sheet includes blank labels providing you the possibility to create
labels with your own texts or symbols.
Service blank label XBT RT
Touch blank label XBT RT
For a detailed description on how to print your own labels see Creating Individual
Labels, page 53
48
33003962 11/2011
Magelis XBT N/R/RT
Inserting Labels
33003962 11/2011
Inserting Labels
6
Inserting Insert Labels
Overview
In order to be sure that each key of the XBT terminals executes the requested
function it is of vital importance that you correctly insert the insert label into the
device. The following paragraphs describe the procedures of inserting insert labels
into XBT N, XBT R and XBT RT terminals.
WARNING
UNINTENDED EQUIPMENT OPERATION
Make sure that the text/symbols on your insert label always correspond to what is
configured for your XBT terminal in the Vijeo-Designer Lite configuration software.
Otherwise the keys of your terminal will not initiate the actions indicated on them.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
33003962 11/2011
49
Inserting Labels
Graphical Representation of Correctly Inserting Labels into XBT N Terminals
The graphic below shows how to correctly insert an insert label into an XBT N
terminal:
Inserting Labels into XBT N Terminals
For inserting insert labels into XBT N terminals proceed as follows:
Step
50
Action
1
Press the pre-cut insert label of your choice out of the insert label sheet.
2
Take your XBT N terminal and turn it around so that you can see its rear panel.
On the left-hand side of the rear panel, located directly behind the overlapping
display, you will find the opening for the insert label.
3
Insert the insert label cautiously into this opening (as shown in steps 1 and 2 of
the above figure) until the 4 key symbols / texts have disappeared and the only
sign that can still be seen of the insert label is the double arrow.
4
Turn your XBT N terminal around and check at its front side that all 4 symbols /
texts are clearly visible at the keys. If the texts / symbols are not clearly visible,
insert the insert label a bit further into the opening. A graphical example of a not
correctly inserted insert label is provided for XBT R / RT terminals below in this
chapter.
5
If the texts / symbols are clearly visible on the front of the terminal, take the part
(with the double arrow sign) of the insert label that is still visible on the rear of the
terminal and slide this flap into the slit indicated in step 3 of the above figure. The
flap should now be flush with the rear of the terminal (see step 4 of the above
figure).
If the insert label has not correctly been inserted into the XBT terminal, the flap
of the insert label will be too long to fit into this slit. A graphical example of a not
correctly inserted insert label is provided for XBT R / RT terminals below in this
chapter.
33003962 11/2011
Inserting Labels
Graphical Representation of Correctly Inserting Labels into XBT R / XBT RT Terminals
The graphic below shows how to correctly insert an insert label into an XBT R /
XBT RT terminal:
Inserting Labels into XBT R / XBT RT Terminals
For inserting insert labels into XBT R / XBT RT terminals proceed as follows:
Step
33003962 11/2011
Action
1
Press the pre-cut insert label of your choice out of the insert label sheet.
2
Take your XBT R / XBT RT terminal and turn it around so that you can see its
rear panel. On the right-hand side of the rear panel, located directly behind the
overlapping display, you will find the opening for the insert label.
3
Insert the insert label cautiously into this opening (as shown in steps 1 and 2 of
the above figure) until the key symbols / texts on the wide part of the insert labels
have disappeared and the wide part of the insert label is flush with the opening.
There will be merely the small flap of the insert label with the double arrow being
visible outside the terminal.
51
Inserting Labels
Step
52
Action
4
Turn your XBT R / XBT RT terminal around and check at its front side that all
symbols / texts are clearly visible at the keys. If the texts / symbols are not clearly
visible, insert the insert label a bit further into the opening.
Front of XBT RT terminal with insert label not correctly inserted
5
If the texts / symbols are clearly visible on the front of the terminal, take the small
part (with the double arrow sign) of the insert label that is still visible on the rear
of the terminal and slide this flap into the slit indicated in step 3 of the above
figure. The flap should now be flush with the rear of the terminal (see step 4 of
the above figure).
If the insert label has not correctly been inserted into the XBT terminal, the flap
of the insert label will be too long to fit into this slit.
Rear of XBT terminal with insert label not correctly inserted
33003962 11/2011
Magelis XBT N/R/RT
Creating Individual Labels
33003962 11/2011
Creating Individual Labels
7
Creating Individual Labels
Overview
For describing the procedure of creating and printing individual texts or symbols on
the blank labels, blank labels of XBT R / RT terminals are used as an example in this
section. The process of printing labels for XBT N terminals is identical, with the
difference that they provide only 1 line of text / symbols.
33003962 11/2011
53
Creating Individual Labels
Creating Individual Labels
To create insert labels with your own texts or symbols, proceed as follows:
Step
54
Action
1
Open the Static Function Keys dialog box in the Vijeo-Designer Lite
configuration software for your XBT terminal type.
2
Click the Print Label button.
Result: A special Microsoft Word template opens.
Microsoft Word template for XBT RT
3
Modify the Word template to create your own key labels.
33003962 11/2011
Creating Individual Labels
Step
4
33003962 11/2011
Action
Print the modified Word document first on a blank paper to create a reference
sheet.
Printout of the modified Word template
55
Creating Individual Labels
Step
56
Action
5
Position the insert label sheet on the reference printout in a way that the keys the
new texts / symbols should be printed on are exactly on top of the new texts /
symbols on the reference printout.
Positioning insert label sheet on the reference printout
6
Fix the insert label sheet on the reference printout using adhesive tape and insert
them in your printer.
7
Activate the print command to print on the insert label sheet.
8
After the texts / symbols have been printed on your insert label sheet, remove
the insert label sheet from the reference printout, press the insert label out of the
sheet and insert it in your terminal as described in section Inserting Insert Labels,
page 49.
33003962 11/2011
Magelis XBT N/R/RT
Connecting XBT Terminals
33003962 11/2011
Connecting XBT Terminals
8
Overview
XBT terminals can be connected to different equipment to perform the following
tasks:
z
z
z
For exchanging software configuration data with Vijeo-Designer Lite, connect the
XBT terminal with a PC where Vijeo-Designer Lite is running.
For controlling an automation system, connect the XBT terminal with a PLC.
For printing alarms as a data stream, alarm log files or a list of current alarms,
connect the XBT terminal with a printer.
The following sections describe how to connect your XBT terminal to the different
equipment and provides safety information concerning the cabling.
What’s in this Chapter?
This chapter contains the following sections:
Section
33003962 11/2011
Topic
Page
8.1
Grounding and Safety
58
8.2
Connecting XBT Terminals to a PC
60
8.3
Connecting XBT Terminals to a PLC
68
8.4
Connecting XBT N401 / R411 / RT511 Terminals to a Printer
80
57
Connecting XBT Terminals
8.1
Grounding and Safety
Safety Information Concerning the Grounding of Terminals
Danger of Point-to-Point Connections Between Separate Buildings
Care must be taken when XBT terminals are directly connected to a PLC that is
located in another building. When you remove the cable from the terminal, you will
loose the protective earth ground of the terminal. Since these 2 buildings can have
different earth grounds, unplugging the cable from the terminal can lead to an
electric shock created by a ground loop (voltage potential difference between two
separate buildings).
DANGER
HAZARD OF ELECTRIC SHOCK DUE TO IMPROPER GROUNDING
z
z
Remove power before installing or maintaining equipment.
Ensure the equipment is properly grounded to the service entrance of the
building.
Failure to follow these instructions will result in death or serious injury.
58
33003962 11/2011
Connecting XBT Terminals
Point-to-point connections between separate buildings
1
2
3
4
5
6
7
8
33003962 11/2011
building 1
building 2
PLC
XBT RT
signal cable
earth ground of building 1
earth ground of building 2
resistance R between the 2 earth grounds
59
Connecting XBT Terminals
8.2
Connecting XBT Terminals to a PC
Overview
The following sections provide information on how to connect XBT terminals to a PC
for exchanging software configuration data.
What’s in this Section?
This section contains the following topics:
Topic
60
Page
Distinguishing XBT Terminals by Power Supply
61
Connecting XBT Terminals Powered by the PLC to a PC
62
Connecting XBT Terminals Powered by an External Power Supply to a PC
65
33003962 11/2011
Connecting XBT Terminals
Distinguishing XBT Terminals by Power Supply
Overview
For exchanging software configuration data with Vijeo-Designer Lite, connect your
XBT terminal to a PC running the Vijeo-Designer Lite configuration software.
The correct cabling depends on whether your XBT terminal is
z
z
powered by the PLC
powered by an external 24 VDC power supply
The following XBT terminals need 5 V power that must be supplied by the PC in this
case:
z
z
z
z
XBT N200
XBT N400
XBT R400
XBT RT500
CAUTION
OVERVOLTAGE DAMAGE TO EQUIPMENT
Make sure to connect the following terminals only to a source providing 5 VDC.
z
z
z
z
XBT N200
XBT N400
XBT R400
XBT RT500
Failure to follow these instructions can result in injury or equipment damage.
NOTE: XBT RT500 terminals are protected against accidental connection to higher
voltages (up to 30 V) but the other terminal types are not and will be damaged.
The following XBT terminals need an external power supply supplying 24 VDC:
z
z
z
z
z
z
33003962 11/2011
XBT N410
XBT N401
XBT NU400
XBT R410
XBT R411
XBT RT511
61
Connecting XBT Terminals
Connecting XBT Terminals Powered by the PLC to a PC
Overview
The following XBT terminals need 5 V power that is usually supplied by the PLC:
z
z
z
z
XBT N200
XBT N400
XBT R400
XBT RT500
When connecting these terminals to a PC for exchanging software configuration
data with Vijeo-Designer Lite, the 5 V required by the terminal must be provided by
the PC.
CAUTION
VOLTAGE DAMAGE TO EQUIPMENT
Connect the serial link connector with power off and tighten connector screws.
Failure to follow these instructions can result in injury or equipment damage.
NOTE: For connecting XBT terminals to a PC use the Schneider cables described
in the following sections.
62
33003962 11/2011
Connecting XBT Terminals
Connecting XBT N200 / N400 / R400 to a PC
XBT N200 / N400 and R400 terminals can be connected to a PC in 2 different ways:
z
z
via the serial port of the PC using the Schneider cable XBT Z945
via the USB port of the PC using the Schneider cables XBT Z925 and TSXCUSB485
Connecting XBT N200 / N400 / R400 to a serial port of a PC using the Schneider
cable XBT Z945
Connecting XBT N200 / N400 / R400 to a USB port of a PC using the Schneider
cables XBT Z925 and TSX-CUSB485.
*
33003962 11/2011
XBT N200 and XBT N400 without logo: you must add a XBT ZN999 cable adapter.
63
Connecting XBT Terminals
Connecting XBT RT500 to a PC
XBT RT500 terminals can be connected to a PC in 2 different ways:
z
z
via the serial port of the PC using the Schneider cable XBT Z945 and the adaptor
XBTZRT999
via the USB port of the PC using the Schneider cables XBT Z925 and TSXCUSB485
Connecting XBT RT500 to a serial port of a PC using the Schneider cable XBT Z945
and the adaptor XBT ZRT999
Connecting XBT RT500 to a USB port of a PC using the Schneider cables
XBT Z925 and TSX-CUSB485
64
33003962 11/2011
Connecting XBT Terminals
Connecting XBT Terminals Powered by an External Power Supply to a PC
Overview
The following XBT terminals need an external power supply supplying 24 VDC:
z
z
z
z
z
z
XBT N410
XBT N401
XBT NU400
XBT R410
XBT R411
XBT RT511
When connecting these terminals to a PC for exchanging software configuration
data with Vijeo-Designer Lite it is also required to connect an external power supply
via the 24 VDC power supply connector that is included in the scope of delivery of
these XBT terminals.
CAUTION
VOLTAGE DAMAGE TO EQUIPMENT
Connect the serial link connector with power off and tighten connector screws.
Failure to follow these instructions can result in injury or equipment damage.
NOTE: For connecting these XBT terminals to a PC use the Schneider cables
described in the following sections.
Connecting XBT N410 / N401 / NU400 / R410 / R411 to a PC
XBT N410 / N401 / NU400 / R410 / R411 terminals can be connected to a PC in 2
different ways:
z
z
33003962 11/2011
via the serial port of the PC using the Schneider cable XBT Z915
via the USB port of the PC using the Schneider cables XBT Z925 and TSXCUSB485
65
Connecting XBT Terminals
Connecting XBT N410 / N401 / NU400 / R410 / R411 to a serial port of a PC using
the Schneider cable XBT Z915
Connecting XBT N410 / N401 / NU400 / R410 / R411 to a USB port of a PC using
the Schneider cables XBT Z925 and TSX-CUSB485
Connecting XBT RT511 to a PC
XBT RT511 terminals can be connected to a PC in 2 different ways:
z
z
66
via the serial port of the PC using the Schneider cable XBT Z945
via the USB port of the PC using the Schneider cables XBT Z925 and TSXCUSB485
33003962 11/2011
Connecting XBT Terminals
Connecting XBT RT511 to a serial port of a PC using the Schneider cable XBT Z945
Connecting XBT RT511 to a USB port of a PC using the Schneider cables
XBT Z925 and TSX-CUSB485
33003962 11/2011
67
Connecting XBT Terminals
8.3
Connecting XBT Terminals to a PLC
Overview
The following sections provide information on how to connect XBT terminals to a
PLC for controlling an automation system.
What’s in this Section?
This section contains the following topics:
Topic
68
Page
Distinguishing XBT Terminals by Power Supply
69
Connecting XBT Terminals Powered by the PLC to a PLC
71
Connecting XBT Terminals Powered by an External Power Supply to a PLC
75
33003962 11/2011
Connecting XBT Terminals
Distinguishing XBT Terminals by Power Supply
Overview
For controlling an automation system, connect your XBT terminal to a PLC.
The correct cabling depends on whether your XBT terminal is
z
z
powered by the PLC
powered by an external 24 VDC power supply
The following XBT terminals need 5 V power that must be supplied by the PLC in
this case:
z
z
z
z
XBT N200
XBT N400
XBT R400
XBT RT500
CAUTION
OVERVOLTAGE DAMAGE TO EQUIPMENT
Make sure to connect the following terminals only to a source providing 5 VDC.
z
z
z
z
XBT N200
XBT N400
XBT R400
XBT RT500
Failure to follow these instructions can result in injury or equipment damage.
NOTE: XBT RT500 terminals are protected against accidental connection to higher
voltages (up to 30 V) but the other terminal types are not and will be damaged.
The following XBT terminals need an external power supply supplying 24 VDC:
z
z
z
z
z
z
XBT N410
XBT N401
XBT NU400
XBT R410
XBT R411
XBT RT511
Data Exchanged Between XBT Terminals and PLCs
Since data are continuously exchanged in a human/machine dialog between an
XBT terminal and a PLC please consider the following recommendations.
Loss of communication between the terminal and the PLC can result in partial or
complete loss of control of the machine.
33003962 11/2011
69
Connecting XBT Terminals
Unplugging the PLC cable during operation may lead to the loss of requests or
responses exchanged between the terminal and the PLC.
WARNING
UNINTENDED EQUIPMENT OPERATION
z
z
Never remove the PLC cable from the XBT terminal while operations are in
progress.
Check the XBT terminal connection by monitoring the communication
monitoring word in the dialog table via the PLC program.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
WARNING
LOSS OF CONTROL
z
z
z
z
The designer of any control scheme must consider the potential failure modes
of control paths and, for certain critical functions, provide a means to achieve a
safe state during and after a path failure. Examples of critical control functions
are emergency stop and overtravel stop.
Separate or redundant control paths must be provided for critical control
functions.
System control paths may include communication links. Consideration must be
given to the implications of unanticipated transmission delays or failures of the
link.*
Each implementation of a Magelis XBT N/R/RT must be individually and
thoroughly tested for proper operation before being placed into service.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
*For additional information, refer to NEMA ICS 1.1 (latest edition), Safety Guidelines
for the Application, Installation, and Maintenance of Solid State Control.
70
33003962 11/2011
Connecting XBT Terminals
Connecting XBT Terminals Powered by the PLC to a PLC
Overview
The following XBT terminals need 5 V power that is usually supplied by the PLC but
may also be supplied by an external 5 VDC power supply:
z
z
z
z
XBT N200
XBT N400
XBT R400
XBT RT500
CAUTION
VOLTAGE DAMAGE TO EQUIPMENT
Connect the serial link connector with power off and tighten connector screws.
Failure to follow these instructions can result in injury or equipment damage.
Connection to Twido / Micro / Premium / Nano, Power by PLC
Use the Schneider cable XBT Z9780 (RS485) to connect XBT N200 / N400 / R400
or RT500 terminals to the following Schneider PLCs that provide the required
5 VDC:
z
z
z
z
Twido
Micro
Premium
Nano
Connection to Twido / Micro / Premium / Nano via Schneider cable XBT Z9780
(RS485)
Connection to Modicon M340, Power by PLC
Use the Schneider cable XBT Z9980 (RS485) to connect XBT N200 / N400 / R400
or RT500 terminals to a Modicon M340 PLC that provides the required 5 VDC.
33003962 11/2011
71
Connecting XBT Terminals
Connection to Modicon M340 via Schneider cable XBT Z9980 (RS485)
Connection to Tesys U, Altivar, Lexium 05, Zelio, Preventa XPS MC, Power by External Power
Supply
To connect XBT N200 / N400 / R400 or RT500 terminals to the following PLCs use
the Schneider ABL8MEM05040 power supply to provide the required 5 VDC
together with the adaptor XBT ZRTPW and the Schneider cable XBT Z9980
(RS485):
z
z
z
z
z
Tesys Model U
Altivar
Lexium 05
Zelio with communication module
Preventa XPSMC
Connection to Tesys Model U, Altivar, Lexium 05, Zelio (with communication
module) or Preventa XPSMC with ABL8MEM05040 power supply with adaptor XBT
ZRTPW and Schneider cable XBT Z9980 (RS485)
72
33003962 11/2011
Connecting XBT Terminals
Connecting XBT RT500 to other Devices
XBT RT500 terminals require different cables for connecting them to individual
PLCs.
Connection to PLCs using the XBT ZG939 and the XBT ZRTPW cable adapter:
Cabling with PLCs:
PLC
Cable
+ XBT ZG939
cable adapter
+ XBT ZRTPW
for power
supply
Advantys STB
XBT Z9715 (RS232)
-
x
Momentum
XBT Z9711 (RS232C)
x
x
Quantum / 984
XBT Z9710 (RS232C)
x
x
Rockwell Micrologix
XBT Z9733 (RS232)
-
x
Rockwell SLC500, Drop 1761NETAIC
XBT Z9734 (RS485)
-
x
Siemens S7-200
XBT ZG9721 (RS485)
-
x
Omron CPM1,CPM2 , CJ1 , CS1
XBT Z9743 (RS232
x
x
Mitsubishi FX
XBT Z980 (RS232)
x
x
33003962 11/2011
73
Connecting XBT Terminals
Communication Interruption with XBT N200 or XBT N400 Terminals
A communication interruption may have occurred if ????? is displayed rather than
any values, or the connection popup remains on the display unit. If you are using an
XBT N200 or an XBT N400 terminal, it may be caused by the cabling because
different cables are required for the different terminal versions. Use the cables as
shown in the table below. If you are using other terminals or the condition still
persists with these cable, refer to section Troubleshooting, page 156 or to the
manual describing the protocol you are using for more information.
RJ45 connector compatibility table
XBT N Front Panel
Cable
Without Telemecanique or Schneider Electric
logo
XBT Z978
With Telemecanique or Schneider Electric logo
XBT Z9780
74
XBT Z9780 + XBT ZN999 adaptor
Application example: XBT N without Telemecanique logo
connected via XBT Z9780 cable and XBT ZN999 adaptor
33003962 11/2011
Connecting XBT Terminals
Connecting XBT Terminals Powered by an External Power Supply to a PLC
Overview
The following XBT terminals need an external power supply supplying 24 VDC:
z XBT N410
z XBT N401
z XBT NU400
z XBT R410
z XBT R411
z XBT RT511
When connecting these terminals to a PLC for controlling an automation system it is
also required to connect an external power supply via the 24 VDC power supply
connector that is included in the scope of delivery of these XBT terminals.
CAUTION
VOLTAGE DAMAGE TO EQUIPMENT
Connect the serial link connector with power off and tighten connector screws.
Failure to follow these instructions can result in injury or equipment damage.
NOTE: For connecting these XBT terminals to a PLC or a fieldbus tap use the
Schneider cables described in the following sections.
Connecting XBT N410 / N401 / NU400 / R410 / R411 to a PLC
XBT N410 / N401 / NU400 / R410 / R411 terminals require different cables for
connecting them to individual PLCs or fieldbus taps.
Use the Schneider cable XBT Z938 (RS485) to connect XBT N410 / N401 / NU400
/ R410 / R411 to the following Schneider PLCs:
z Tesys Model U
z Altivar
z Lexium 05
z Zelio with communication module
z Preventa XPSMC
33003962 11/2011
75
Connecting XBT Terminals
Connection via the Schneider cable XBT Z938 (RS485):
To connect your XBT terminal to other PLCs or fieldbus taps refer to the lists below
showing the adequate cables.
Connection to PLCs or fieldbus taps using different Schneider cables:
Cabling with PLCs:
PLC
76
Cable
Advantys STB
XBT Z988 (RS232)
Momentum
XBT Z9711 (RS232C)
Quantum / 984
XBT Z9710 (RS232C)
Twido/Micro/Premium/Nano
XBT Z968 / Z9680 (RS485)
Modicon M340
XBT Z938 (RS485)
Rockwell SLC500 , Drop 1761NETAIC
XBT Z9730 (RS232)
Rockwell Micrologix
XBT Z9731 (RS232)
Mitsubishi FX
XBT Z980 (RS232/RS422)
Siemens S7-200
XBT Z9721 (RS485)
Omron CPM1 , CPM2 , CJ1 , CS1
XBT Z9740 (RS232)
33003962 11/2011
Connecting XBT Terminals
Cabling with fieldbus taps:
PLC
Cable
LU9 GC3
XBT Z938 (RS485)
SCA62 (multipoint)
XBT Z908 (RS485)
SCA64
XBT Z908 (RS485)
TWDXCAT3RJ, TWDXCAISO
XBT Z938 (RS485)
Connecting XBT RT511 to a PLC
XBT RT511 terminals require different cables for connecting them to individual
PLCs or fieldbus taps.
Use the Schneider cable XBT Z9980 (RS485) to connect XBT RT511 to the
following Schneider PLCs:
z Tesys Model U
z Altivar
z Lexium 05
z Zelio with communication module
z Preventa XPSMC
Connection via the Schneider cable XBT Z9980 (RS485):
To connect your XBT terminal to other PLCs or fieldbus taps refer to the lists below
showing the adequate cables.
33003962 11/2011
77
Connecting XBT Terminals
Connection to PLCs or fieldbus taps using different Schneider cables:
Cabling with PLCs:
PLC
Cable
+ XBT ZG939 cable adapter
Advantys STB
XBT Z9715 (RS232)
-
Momentum
XBT Z9711 (RS232C)
x
Quantum / 984
XBT Z9710 (RS232C)
x
Twido/Micro/Premium/Nano
XBT Z9780/Z9782 (RS485)
-
Modicon M340
XBT Z9980/Z9982 (RS485)
-
Rockwell Micrologix
XBT Z9733 (RS232)
-
Rockwell SLC500 , Drop 1761NETAIC
XBT Z9734 (RS485)
-
Siemens S7-200
XBT ZG9721 (RS485)
x
Omron CPM1, CPM2, CJ1 , CS1
XBT Z9743 (RS232
x
Cabling with fieldbus taps:
PLC
Cable
+ XBT ZG939 cable adapter
LU9 GC3
XBT Z9980 (RS485)
-
SCA62 (multipoint)
XBT Z908 (RS485)
x
SCA64
XBT Z908 (RS485)
x
TWDXCAT3RJ, TWDXCAISO
XBT Z9980 (RS485)
-
78
33003962 11/2011
Connecting XBT Terminals
Connecting XBT N401 / R411 / RT511 to Zelio
XBT N401 / R411 / RT511 terminals require cable SR2CBL08 for connecting to
Zelio.
Connection via the Schneider cable SR2CBL08:
Connecting XBT N401 / R411 / RT511 to Millenium
33003962 11/2011
79
Connecting XBT Terminals
8.4
Connecting XBT N401 / R411 / RT511 Terminals to
a Printer
Printer Connections
Overview
XBT N401, XBT R411 and XBT RT511 terminals provide a MiniDIN connector on
their rear panel for connecting an RS232C printer.
Connecting XBT N401 / R411 / RT511 to a Printer
Use the Schneider cable XBT Z926 to connect your XBT N40, XBT R411 or
XBT RT511 terminal to an RS232C printer.
Printer connection via Schneider cable XBT Z926
80
33003962 11/2011
Magelis XBT N/R/RT
Overview of Applications and Functions
33003962 11/2011
Overview of Applications and
Functions
9
Overview
This chapter provides an overview of applications and functions of XBT terminals.
What’s in this Chapter?
This chapter contains the following sections:
Section
33003962 11/2011
Topic
Page
9.1
Overview of Functions
82
9.2
XBT Terminals in HMI Applications
83
9.3
Functions of Keys, Touchscreen, LEDs
86
81
Overview of Applications and Functions
9.1
Overview of Functions
Overview of XBT Terminal Functions
Overview
The flowchart below shows the different functions of XBT terminals.
Representation
82
33003962 11/2011
Overview of Applications and Functions
9.2
XBT Terminals in HMI Applications
HMI Applications
HMI Application Example
The figure below shows a typical HMI application with XBT R411.
33003962 11/2011
No.
Description
1
XBT R411: terminal for visualizing data of the PLC
2
XBT R411: LED indicating the communication status
3
XBT R411 sends the alarms risen by the PLC on the flow to the printer
4
PC with Vijeo-Designer Lite for programming the XBT R411
5
XBT R411: keys for sending commands to the automation system
z changing the panel
z viewing current alarms
z modifying digits in variable edition
z activating the function associated with functional links
83
Overview of Applications and Functions
No.
Description
6
XBT R411: keys for modifying parameters of the PLC
z acknowledging alarms
z sending commands to the PLC
z entering values
7
Connection to a PLC
XBT N and XBT RT terminals provide different operating variants. Depending on the
selected variant the keypad is either in control variant or in input variant or in touch
variant (only XBT RT). In each variant, the individual keys provide different functions
(for further information see Overview of Keys on the Individual XBT Terminals,
page 34). To indicate the different functions to the user, the key labels are
interchangeable. Blank labels are provided that can be filled with individual texts.
Types of HMI Applications
Applications for XBT terminals are created in the Vijeo-Designer Lite software. They
can be associated with:
z
z
z
z
production monitoring
preventive maintenance
corrective maintenance
process control
Production Monitoring Example
In production monitoring applications XBT terminals display process status
messages.
XBT terminal displaying a process status message:
Preventive Maintenance Example
In preventive maintenance applications XBT terminals count parts for production
monitoring.
XBT terminal counting parts:
84
33003962 11/2011
Overview of Applications and Functions
Corrective Maintenance Example
In corrective maintenance applications XBT terminals indicate process conditions.
XBT terminal indicating process conditions:
Process Control Example
In process control applications XBT terminals provide process control via
configurable function keys.
XBT terminal providing process control via configurable function keys:
As indicated on the display unit of the XBT N in the above figure, the function
pressurizing is controlled by the key named P and the function start cycle is
controlled by the key named SC.
33003962 11/2011
85
Overview of Applications and Functions
9.3
Functions of Keys, Touchscreen, LEDs
Overview
The following sections describe the functions of keys, touchscreen and LEDs on the
different XBT terminal types.
What’s in this Section?
This section contains the following topics:
Topic
86
Page
Functions of Keys and Touchscreen
87
Functions of LEDs on XBT N401 / XBT R411 / XBT RT511 Terminals
90
33003962 11/2011
Overview of Applications and Functions
Functions of Keys and Touchscreen
Overview
All XBT terminals provide keys on their front panels that perform different functions.
XBT R and XBT RT terminals provide specific keys, that can have 2 different
functions depending on the current operating mode, the so-called dual labelled
keys.
XBT RT terminals are additionally equipped with a touchscreen that allows
execution of certain functions by pushing elements directly on the display unit of the
terminal.
Functions of Keys
The functions of the individual keys provided on XBT terminals are listed in the
following table:
Key
Key Function
Select a field for edition or move on to the next field each time MOD is pressed
(left to right and top to bottom).
z exit the alarm display
z return to the previous panel (the last 16 panels are memorized)
z exit an edition without acceptance of the value entered
z
z
z
z
change panel in a menu
navigate in the alarm list or in the history list
select a digit in a variable field during edition
Activate the function associated with a functional link:
z impulse command
z toggle command
z writing variables
z set / reset bit
z go up/down within a panel (for XBT terminals providing the scrolling
z
z
z
z
function)
select a functional link in the panel
increment/decrement the selected digit
increment/decrement the value of a variable field
select a value in a selection list, and modify a digit in a variable field during
input
z delete the selected digit or field
z confirm a selection
z confirm an edition
z acknowledge an alarm
33003962 11/2011
87
Overview of Applications and Functions
Key
Key Function
static function keys
z access a panel
z execute an impulse command
z execute a toggle command
z modify a value
only for XBT RT: dynamic function keys having panel-dependant functions
z access a panel
z execute an impulse command
z execute a toggle command
z set / reset bit
Dual Labelled Keys on XBT R and XBT RT Terminals
XBT R and XBT RT terminals provide dual labelled keys.
For XBT R terminals this means that keys F1 to F12 are function as well as numeric
keys, i.e. they can act as function keys as well as service keys.
They operate as follows:
z
z
If the user is not modifying a value, the keys act as function keys.
If the user is modifying the value of a field, the keys automatically act as service
keys for edition mode.
NOTE: It is impossible to enter a value if a function key has been pressed, in the
same way that it is impossible to leave edition mode if the value of a field is being
modified.
For XBT RT terminals operated in touch variant, this means that keys F1 to F4 have
different functions, depending on the selected terminal mode.
z
z
88
In edition mode, keys F1 to F4 act as arrow keys.
In normal mode, keys F1 to F4 act as static function keys.
33003962 11/2011
Overview of Applications and Functions
Touchscreen on XBT RT Terminals
XBT RT terminals are equipped with a touchscreen that allows execution of
functions by pushing elements directly on the display unit of the terminal.
You can activate HMI objects for edition mode by directly pressing the requested
object on the touchscreen.
You can activate the function of a button displayed on the display unit of the terminal
by directly pressing on this button.
CAUTION
EQUIPMENT DAMAGE
z
z
Activate the touchscreen with fingers only.
Never use sharp instruments, such as screwdrivers, as they may damage the
touchscreen.
Failure to follow these instructions can result in injury or equipment damage.
33003962 11/2011
89
Overview of Applications and Functions
Functions of LEDs on XBT N401 / XBT R411 / XBT RT511 Terminals
Overview
The table below lists the functions of the LEDs provided on XBT N401, XBT R411
and XBT RT511 terminals.
LED
Color
Status
Meaning
Communication
Amber
Off
No cable or no communication
Blinking
Communication OK
Alarms
Red
Alarm list:
Off
Touch
Green
Empty
On
Alarms already displayed
Blinking
New alarms not previously displayed
Only available for XBT RT 511
Off
When there is no activity on the touchscreen or
function key
On
When you press the touchsceeen or function keys
Input variant
Up/Down
Green
Off
Key inactive
On
Possibility of going up/down within a panel
Blinking
Indicates the possibility:
z of selecting a value in a list
z of incrementing/decrementing the selected digit
Off
On
These LEDs are governed by the automation
system. Their state is determined entirely by the
application program of the automation system
governing the terminal. As a result, their role can vary
from application to application:
z Signaling linked to the key (same type of role as
the system LEDs above)
z Signaling the status or a condition of the
component governed by the key
Control variant
LED for static function keys
90
Green
(XBT N)
Amber
(XBT R/R
T)
33003962 11/2011
Magelis XBT N/R/RT
Operating Principles of XBT Terminals
33003962 11/2011
Operating Principles of XBT
Terminals
10
Overview
This sections describes general principles concerning the operation of XBT
terminals.
What’s in this Chapter?
This chapter contains the following sections:
Section
33003962 11/2011
Topic
Page
10.1
Modes of Operation
10.2
Panel Structure of XBT Terminals
10.3
General Configuration Settings
113
10.4
Password-Protection
119
92
99
91
Operating Principles of XBT Terminals
10.1
Modes of Operation
Overview
This section provides an overview of the 2 modes of operation of XBT terminals and
describes their selection process.
What’s in this Section?
This section contains the following topics:
Topic
92
Page
Introduction
93
Automatic Selection of the Mode of Operation
94
Transfer Mode
95
Operating Mode
97
33003962 11/2011
Operating Principles of XBT Terminals
Introduction
Overview
Magelis XBT terminals provide the following 2 modes of operation:
z
z
In Transfer mode dialog applications can be exchanged between the PC running
the Vijeo-Designer Lite software and the Magelis XBT terminal.
In Operating mode data is exchanged between the XBT terminal and the
automation system (controlling the latter).
These 2 modes of operation will be described in the following sections.
33003962 11/2011
93
Operating Principles of XBT Terminals
Automatic Selection of the Mode of Operation
Overview
On power-up, the XBT terminal automatically detects the equipment connected on
its serial link and enables the suitable mode of operation (only one mode at a time).
Process of Selecting the Mode of Operation
Graphical presentation of the process of selecting the mode of operation
94
33003962 11/2011
Operating Principles of XBT Terminals
Transfer Mode
Overview
In transfer mode the XBT terminal communicates with the Vijeo-Designer Lite
configuration software. Software applications can be transferred in both directions.
The XBT terminal automatically enables the transfer mode when it is connected to
a PC via a communication cable. No operator action on the terminal is necessary in
this mode.
Procedure of Transferring Software Applications
For transferring software applications to or from your XBT terminal perform the
following steps:
Step
33003962 11/2011
Action
1
Connect your XBT terminal to a PC running the Vijeo-Designer Lite software. For
the suitable Schneider cable see Connecting XBT Terminals to a PC, page 60.
Result: The XBT terminal automatically detects the connection to a PC, enables
the transfer mode and waits for software application transfer.
2
From the Vijeo-Designer Lite software at your PC start the software application
transfer.
For transferring software configuration data from the PC to the XBT terminal,
select the menus Device →Download....
For transferring software configuration data from the XBT terminal to the PC,
select the menus Device →Upload....
XBT terminals that are equipped with a communication LED indicate data
interchange with a PC by a blinking communication LED.
95
Operating Principles of XBT Terminals
Transfer Mode Process
Transfer mode application example
96
No.
Description
1
XBT N401
2
Transfer cable (for a list of Schneider cables refer to Connecting XBT Terminals to
a PC, page 60)
3
PC with Vijeo-Designer Lite
33003962 11/2011
Operating Principles of XBT Terminals
Operating Mode
Overview
The operating mode is used for data interchange between the XBT terminal and the
automation system to control the automation system. The following tasks can be
performed in this mode of operation:
z
z
z
z
panel display
edition/modification of automation system architecture parameter values
process control (discrete)
viewing and acknowledging alarms
The XBT terminal automatically enables the operating mode when it is connected to
a PLC via a communication cable.
Accessing Panels in Operating Mode
When the XBT terminal is connected to a PLC, the XBT terminal automatically
displays the default panel after start-up. This default panel allows navigation to the
remaining panels.
To navigate between panels and to access a selected panel use the arrow keys of
your XBT terminal:
Arrow Keys
Function
To navigate to another panel, press the up and down arrows of your
XBT terminal.
To access a selected panel, press the right arrow of your XBT
terminal.
Example of Accessing Panels in Operating Mode
The following 2 figures illustrate how to navigate from a default panel to a panel of
your choice (target panel).
Default panel
33003962 11/2011
97
Operating Principles of XBT Terminals
To open the Maintenance panel, press the arrow down key twice to select and then
click the arrow right key to open it.
Target panel
98
33003962 11/2011
Operating Principles of XBT Terminals
10.2
Panel Structure of XBT Terminals
Overview
XBT terminals display panels on their display unit. These panels can contain notanimated objects (e.g. background images, static texts) and not animated HMI
objects (e.g. value displays, bar graphs). 3 different types of are used in XBT
terminals:
z
z
z
application panels
alarm panels
system panels
What’s in this Section?
This section contains the following topics:
Topic
Principle of Application Panels
33003962 11/2011
Page
100
Displaying Application Panels
101
Principle of Alarm Panels
105
Alarm Management
106
Principle of System Panels
109
Displaying System Panels
110
Scrolling within Panels
111
99
Operating Principles of XBT Terminals
Principle of Application Panels
Definition
Application panels are panels designed to provide information about the automation
system architecture being run. They also serve to clarify any operation that the
operator might have to carry out in a given context.
Application panels can be interlinked to create authorized sequences during
operation.
Unauthorized operators can be prevented from displaying protected panels.
100
33003962 11/2011
Operating Principles of XBT Terminals
Displaying Application Panels
Default Panel on Power-Up
When designing the application in Vijeo-Designer Lite, the designer can select a
default panel.
When the terminal is powered up, this is the first panel to be displayed.
There are different ways to display application panels:
z
z
z
z
z
z
by pressing function keys
by activating navigation links provided on other application panels
by pressing a button object or an active area on the touchscreen (XBT RT only)
by pressing dynamic function keys Ri on products supporting this function
via the PLC
by activating links provided on system panels
Via Function Keys
It is possible to display a panel directly by pressing a function key.
Example
Pressing a function key for opening a specific panel:
1
function key
Via Button Object or Active Area on Touchscreen
By using the touchscreen of XBT RT terminals operated in touch variant you can
directly access a specific panel by pressing a button object or an active area
provided on the actually displayed application panel.
33003962 11/2011
101
Operating Principles of XBT Terminals
Pressing a button for opening a specific panel:
Via Navigation Links
You can directly access a specific panel by using a navigation link provided on the
actually displayed application panel.
The following 2 figures illustrate how to navigate to a specific panel using a
navigation link.
Source panel
1
Navigation link
To navigate directly to the Maintenance panel, select the arrow next to
Maintenance and activate this link (by using the arrow keys of the front panel or
directly touching the arrow on the touchscreen).
Target panel
102
33003962 11/2011
Operating Principles of XBT Terminals
Via the PLC
A specific panel is displayed because the program has written the number of the
panel to be processed in a word in the dialog table (for more information see
Exchanging Data with the Automation System via the Dialog Table, page 151).
The following figure illustrates how a specific panel is opened by the PLC.
PLC opening a specific panel
No.
Description
1
Program, Display panel 25
2
Table read by the terminal
3
Display panel 25
4
Write acknowledgment, panel to be processed H’FFFF’
5
Dialog table
The PLC dialog table contains the number of the panel to be processed (1). The XBT
terminal reads the dialog table in the PLC (2) and displays the desired panel (3).
Once the command has been processed, the XBT terminal writes the value H’FFFF’
in the panel to be processed word (4), to acknowledge the request to the PLC
program.
From System Panels
You can directly access a specific panel by using a navigation link provided on a
system panel.
The following figure shows a system panel providing links to application panels.
33003962 11/2011
103
Operating Principles of XBT Terminals
System panel with links to application panels
To navigate directly to the LIST OF ALARMS panel, select the arrow next to LIST
OF ALARMS and activate this link (by using the arrow keys of the front panel or
directly touching the arrow on the touchscreen).
For more information about system panels, see Principle of System Panels,
page 109
104
33003962 11/2011
Operating Principles of XBT Terminals
Principle of Alarm Panels
Objective
An alarm panel has the same characteristics as an application panel with respect to:
z
z
the text
the fields
The first line of an alarm panel is preconfigured (by Vijeo-Designer Lite) to show:
z
z
z
the dates and times of alarm appearance/disappearance and acknowledgment
the ranking of the alarm in the alarm list
the total number of alarms in the list
The advantage of an alarm panel lies in its event-triggered display. Each alarm
panel is associated with a word bit in the dialog table.
If the bit is at state 1, the panel is displayed and the text blinks.
Example
Example of an alarm panel
1 Line time-stamped by the XBT terminal (A for Alarm), the alarm text appears
blinking and changes to a steady display once it has been acknowledged.
Listing Alarms in Operating Mode
z
z
33003962 11/2011
When an alarm appears, it is often the consequence of other alarms. Due to their
priority system, XBT terminals can display the most important alarm, i.e. the
alarm that is presenting the highest risk to the automation system architecture.
All alarms are time-stamped on appearance.
105
Operating Principles of XBT Terminals
Alarm Management
Alarm Indication
The actual display of an alarm depends on the priority it has been allocated (see
section Display Priority below).
Alarms pending on the automation system architecture are stored in an alarm list.
The graphic below shows an Alarm LED.
The Alarm LED continuously informs the operator about the state of the alarm list:
z
z
z
Off: The alarm list is empty.
Blinking: The alarm list contains alarms which have appeared since the alarm list
was viewed (new alarms).
On: The alarm list contains alarms which occurred before the alarm list was
viewed (alarms already displayed).
Display Priority
A priority can be associated with each alarm panel. An alarm panel has priority over
an application panel and a system panel. An alarm panel does not have priority over
a value, which is currently being entered.
Different alarm panels may have different priorities. There are 16 possible levels of
priority (the lowest display priority being priority no. 16).
Exception of Priority 0
When an alarm appears on the automation system architecture that is allocated to
a priority 0 alarm panel, the following will happen:
z
z
The alarm panel is not displayed, but stored in the alarm list, thus the current
display will not be disturbed.
The alarm LED blinks to signal the alarm.
When an alarm is activated, it is stored in the alarm list by the terminal.
Appearance Types
Alarm panels can appear in different ways. Alarm panels can be:
z
z
z
106
displayed directly on the display unit
printed directly from XBT terminals equipped with a printer connector (datastream printing)
stored in the list of current alarms
33003962 11/2011
Operating Principles of XBT Terminals
Storage Principle in the Alarm List
If the alarms have equal priority, they are stored from the oldest to the most recent.
If the display unit is available (i.e., not occupied by a higher-priority display), the
oldest alarm is displayed. In an automation system, it is often the oldest alarm that
is the most interesting, as the more recent alarms are often a consequence of the
condition signaled by the first alarm (classic case of bursts of alarms).
If alarms with higher priority occur the following will happen:
z
z
Alarms with higher priority are stored at the top of the list.
If the display unit is available (i.e., not occupied by a higher-priority display), the
new alarm with highest priority will be displayed.
Buzzer for Alarms Notification
You can set alert sounds to inform you of alarms by activating the buzzer of the
XBT RT511 terminal.
Acknowledg-ment of Alarms
When designing alarm panels, it is possible to define whether the alarm panel
should be acknowledged systematically by the operator (obligatory
acknowledgment) or not.
To acknowledge the alarm panel on the display press ENTER. The alarm message
changes to a steady display.
Depending on the choice made, management of these 2 types of alarm is as follows:
33003962 11/2011
Alarms which must be acknowledged
(obligatory)
Alarms which can be acknowledged but
do not have to be
An alarm, which must be acknowledged,
remains in the alarm list until it is
acknowledged by the operator, even if the
cause of the alarm has disappeared.
An alarm, which can be acknowledged but
does not have to be, disappears from the
alarm list as soon as the cause of the alarm
has disappeared, regardless of whether or
not it has been acknowledged by the
operator.
Advantage: Picks up transient conditions
(instability of a discrete sensor, for example).
Advantage: The display unit is not
monopolized by displaying alarms
considered to be of minor importance to the
application.
107
Operating Principles of XBT Terminals
Alarm Log
The terminals can manage a log of the alarm panels. They store the alarm panels
with the text, but without variable values (for more information, see Alarm Log,
page 143).
Display Principle of Alarm Panels
Representation
108
33003962 11/2011
Operating Principles of XBT Terminals
Principle of System Panels
Definition
System panels are predefined panels which are used to perform operations relating
to the XBT terminal "system".
In operating mode, these panels can be accessed in the same way as application
panels.
System panels are panels processed as if they were application type panels. Hence
they are stored with the application panels in the developed application file.
There are 3 types of system panels:
z
z
z
standard system panels, which can be called by accessing an application panel
(numbers 1 to 100)
system panels, which cannot be called by accessing an application panel
(numbers 101 to 200)
popup/message system panels, which cannot be called (numbers 201 to 300)
The advantage of being able to view these panels with Vijeo-Designer Lite is that
system messages can be translated.
33003962 11/2011
109
Operating Principles of XBT Terminals
Displaying System Panels
Overview
System panels are accessed by means of function keys or navigation links.
When designing the application in Vijeo-Designer Lite, the designer can choose the
system panels that should be associated with these keys, or these links.
List of System Panels
The following system panels are available to HMI operators:
110
Number
Name
Description
2
panel list
displays a list of all application panels you can access,
depending on your security access level
The panels protected by password are listed only. The
current security access level is in conformance with the
security access level of the panel.
3
alarm list
displays a list of all the active alarms triggered by the
automation system
4
alarm history
displays a list of the last events of the alarm history (coming
alarms, going alarms, communication interruptions)
7
password
On this panel you can enter the password to change the
security access level (A, B, C, or blank password).
10
default system
panel
When a terminal cannot boot and displays a certain panel
(for example, the first panel is protected by password), then
the terminal displays the default system panel automatically.
22
language
On this panel you can choose the language of the terminal.
30
printer
displays the communication parameters for the second
serial line (only significant for terminals supporting a second
serial line)
100
protocol
displays the parameters for the communication with the
equipment connected on the automation network
110
advanced
displays internal alarm counters
These internal alarm counters can be of interest during calls
to the technical support.
33003962 11/2011
Operating Principles of XBT Terminals
Scrolling within Panels
Overview
Scrolling is necessary in XBT N and XBT R terminals to view the entire panel that
contains more lines than the display unit can display. When opening a panel the first
n (n being the number of lines on the display unit) lines of this panel are displayed
on the display unit. For example, four lines for the XBT N400 terminal.
Example
The other lines can be displayed by scrolling up or down the panel using the up and
down keys on the keypad.
33003962 11/2011
111
Operating Principles of XBT Terminals
112
33003962 11/2011
Operating Principles of XBT Terminals
10.3
General Configuration Settings
Overview
This section describes general settings concerning the HMI language, the date and
time format as well as access to product reference and line parameters.
What’s in this Section?
This section contains the following topics:
Topic
33003962 11/2011
Page
Accessing Configuration Parameters via the System Panel SYSTEM
114
Selecting the HMI Language
115
Selecting the Date and Time Format
116
Accessing the Product Reference
117
Accessing the Line Parameters
118
113
Operating Principles of XBT Terminals
Accessing Configuration Parameters via the System Panel SYSTEM
Overview
It is possible to configure certain terminal parameters when the terminal is in
operating mode, without going into Vijeo-Designer Lite.
The configuration parameters are accessed via the SYSTEM system panel (for
displaying system panels, see Displaying System Panels, page 110).
114
33003962 11/2011
Operating Principles of XBT Terminals
Selecting the HMI Language
Overview
In the HMI Language system panel choose one of the languages configured by the
designer.
33003962 11/2011
115
Operating Principles of XBT Terminals
Selecting the Date and Time Format
In the DATE/TIME panel set the current date and time and define the date and time
display format of your choice.
Entering Date and Time
The date and time values are entered in the same way as a variable alphanumeric
field (for further information see Entering a Value in an Edition Field, page 135).
Selecting Display Format
The format can be configured using the Vijeo-Designer Lite program, during terminal
configuration.
The time format selected applies to all times and dates processed by the software,
including the dates and times printed and/or displayed in the log and in the alarm list.
Example
The following display formats are available:
Date formats
Time formats
DD/MM/YYYY
24:mm:ss
MM/DD/YYYY
12:mm:ss
YYYY/MM/DD
Please note that the time you entered is only valid as long as the terminal is powered
on. As soon as you power off the product the time will be lost.
116
33003962 11/2011
Operating Principles of XBT Terminals
Accessing the Product Reference
Overview
The references of the XBT terminals can be accessed from the system panels.
The references of the XBT terminal can be obtained if the designer has provided
access to these panels (link to the system panels).
The following information is displayed:
z
z
z
z
z
z
z
product reference
name of the application developed in Vijeo-Designer Lite
date and time when the application file was saved in Vijeo-Designer Lite
communication protocol name
version of Vijeo-Designer Lite used to create the application
XBT terminal BIOS reference and version
XBT terminal application software reference and version
NOTE: The most important information is placed on the first few lines so that it is
displayed consecutively, avoiding the need to scroll through the panel.
33003962 11/2011
117
Operating Principles of XBT Terminals
Accessing the Line Parameters
Overview
System panels contain detected error counters whose content is protocoldependent. For further information refer to the XBT protocol manual describing the
protocol you are using.
118
33003962 11/2011
Operating Principles of XBT Terminals
10.4
Password-Protection
Accessing Password-Protected Panels, Fields, Functional Links
Protection
To be sure that only authorized persons are able to read and write data, it is possible
to protect:
z
z
z
access to panels
modification of fields
control via functional links
If an operator does not have authorization:
z
z
protected panels no longer appear in the list of panels
protected fields behave as if they had been configured as read-only
Password
To access password-protected areas enter your password via the Password
system panel. A navigation link to the Password system panel is required on one of
the application panels. (For more information about how system panels are
displayed, see Displaying System Panels, page 110).
XBT terminals provide three access levels: A, B and C.
The passwords for these levels are defined in Vijeo-Designer Lite. A password
consists of four alphanumeric characters (default value: 1111).
33003962 11/2011
119
Operating Principles of XBT Terminals
120
33003962 11/2011
Magelis XBT N/R/RT
Communication with the Automation System
33003962 11/2011
Communication Between XBT
Terminals and the Automation
System
11
Overview
This chapter provides information about the communication between XBT terminals
and the automation system, listing the types of commands and how they are
activated as well as the processes of entering / modifying values or handling alarms.
What’s in this Chapter?
This chapter contains the following sections:
Section
33003962 11/2011
Topic
Page
11.1
Types of Commands
11.2
Activating Commands
125
11.3
Entering / Modifying Values Alphanumeric Fields in Edition
Mode
132
11.4
Handling Alarms
140
11.5
Printing Alarms
144
122
121
Communication with the Automation System
11.1
Types of Commands
Overview
This section describes the 2 types of commands that can be sent via function keys
(or functional links) or button object on touchscreen of the XBT terminal to the
automation system:
z
z
impulse commands
toggle commands
What’s in this Section?
This section contains the following topics:
Topic
122
Page
Impulse Commands
123
Toggle Commands
124
33003962 11/2011
Communication with the Automation System
Impulse Commands
Impulse Command
The automation system is activated by pressing a function key (or functional link) or
button object on touchscreen of XBT RT terminals. If the key (or functional link) is
released, the action stops.
Example
Motor command
33003962 11/2011
Key
Bit
released
0
pressed
1
released
0
123
Communication with the Automation System
Toggle Commands
Toggle Command
The automation system is activated by pressing the function key (or functional link)
or button object on the touchscreen of XBT RT terminals. If the function key (or
functional link) is pressed again, the action on the control system stops.
Example
Conveyor forward command
124
Key
Bit
released
0
pressed
1
released
1
pressed
0
33003962 11/2011
Communication with the Automation System
11.2
Activating Commands
Overview
This section describes the different ways commands can be activated at XBT
terminals.
What’s in this Section?
This section contains the following topics:
Topic
33003962 11/2011
Page
Activating Commands via Functional Links, Button Objects or Dynamic
Function Keys on the Display Unit
126
Activating Commands via Function Keys on the Display Unit
131
125
Communication with the Automation System
Activating Commands via Functional Links, Button Objects or Dynamic
Function Keys on the Display Unit
Overview
Functional links, button objects and dynamic functions are integrated by the
application designer on the different panels to create additional control functions.
To activate functional links, use the left and right keys on the front panel of the XBT
terminals.
To activate buttons, press the button directly on the screen if your XBT terminal is
equipped with a touchscreen. If your XBT terminal is not equipped with a
touchscreen, press the MOD key to select the button and the ENTER key to activate
the button.
Example of a button object
To activate dynamic functions, use the Ri keys on the front panel of the XBT
terminals. These keys can also be linked to pictograms on screen.
Example of dynamic function keys linked to pictograms on screen
Links, button objects and dynamic functions are programmed by the application
designer to send different types of commands to the equipment from the application
panel:
z
z
z
126
impulse commands
toggle commands
set value
33003962 11/2011
Communication with the Automation System
z
z
reset value
write value
Functional Link
Example
No.
33003962 11/2011
Description
1
Change panel (link blinking to indicate that it is active)
2
Change panel
3
Toggle (link blinking to indicate that it is active)
127
Communication with the Automation System
Representation of Command Links
Example
No.
Description
1
Toggle
2
Impulse (link blinking to signal that the link is active)
Buttons
Example of XBT RT in touch variant
128
33003962 11/2011
Communication with the Automation System
No.
Description
1
Push button on touchscreen to go to the Conveyorpanel.
2
Push button on touchscreen to activate the function.
Example of XBT RT in No-touch variant
33003962 11/2011
No.
Description
1
Press the MOD key once to select the button.
2
Press the ENTER key to go to the Conveyor panel.
3
Press MOD and ENTER to activate the function.
129
Communication with the Automation System
Dynamic Function Keys
Example of dynamic function keys linked to pictograms
130
No.
Description
1
Pictograms illustrating the functions of the dynamic function keys.
2
Dynamic function keys.
33003962 11/2011
Communication with the Automation System
Activating Commands via Function Keys on the Display Unit
Example
Function key
1
Function key
The dialog table enables dialog between the PLC and the terminal. In this table, one
word is reserved to supply the PLC with the status of the function keys in the form
of a word bit.
Bit 15 to
Bit 12
Bit
11
Bit
10
Bit
9
Bit
8
Bit
7
Bit
6
Bit
5
Bit
4
Bit
3
Bit
2
Bit
1
Bit
0
Reserved
F12
F11
F10
F9
F8
F7
F6
F5
F4
F3
F2
F1
33003962 11/2011
131
Communication with the Automation System
11.3
Entering / Modifying Values Alphanumeric Fields
in Edition Mode
Overview
This section describes how to select and modify alphanumeric fields, i.e. fields that
allow to enter characters (A-Z) and numbers (0-9).
What’s in this Section?
This section contains the following topics:
Topic
132
Page
Accessing an Alphanumeric Edition Field
133
Entering a Value in an Edition Field
135
Confirming / Cancelling an Edition
137
Exit Edition on Time Out
138
Edition Report
139
33003962 11/2011
Communication with the Automation System
Accessing an Alphanumeric Edition Field
Overview
Alphanumeric edition fields can either be accessed by the user or by the automation
system.
User Selecting an Edition Field
To access an alphanumeric edition field, it must first of all be visible on the display
unit. To select the field, press the MOD key of the XBT terminal.
If there are several edition fields available on the actually displayed panel, press the
MOD key several times in succession to run through the variable fields in edition
mode from left to right and from top to bottom.
You access an alphanumeric edition field on XBT RT terminals in touch variant
directly by touching the screen if an active area has been configured by the HMI
application designer.
Example
Selecting an edition field out of several edition fields on the same panel:
1st time MOD is pressed:
If no edition has been made in any field on the display
unit since the panel was displayed, the top left-hand
field on the display unit is the edition field (field no. 1)
Otherwise the edition field will be the one that has
already been edited (field no. 1, 2, 3 or 4).
We will assume that field no. 1 is the edition field
33003962 11/2011
2nd time MOD is pressed:
Edition field no. 2
3rd time MOD is pressed:
Edition field no. 3
4th time MOD is pressed:
Edition field no. 4
133
Communication with the Automation System
5th time MOD is pressed:
Edition field no. 1, etc.
Field no. 5 cannot be the edition field because it is not visible on the display unit.
Automation System Accessing an Edition Field
The connected device sets a variable field into edition mode by writing its number in
a word in the dialog table. To display the number of variable fields in Vijeo-Designer
Lite, use the Layout →Display Fields Indices menu.
In return, the XBT terminal writes the number of the field being completed in a word
in the dialog table (see Exchanging Data with the Automation System via the Dialog
Table, page 151).
Specific feature of this type of selection:
You cannot select another variable field at the XBT terminal until the one requested
by the connected device has been completed because the MOD key is inactive
during this time.
134
33003962 11/2011
Communication with the Automation System
Entering a Value in an Edition Field
Input Methods
Before you can enter a value in an edition field, activate the input mode in the XBT
terminal.
After you have activated the input mode for a field, the whole field blinks and the
following edition methods are available:
z
z
z
z
accelerated incremental edition
thumbwheel edition
direct edition
direct edition via virtual numeric keypad
Edition
Methods
Key
Description
Accelerated
Incremental
Edition:
Down/Up
The total value of the field is increased or decreased by pressing the up/down
keys.
Thumbwheel
Edition:
Left/Right
z First, the digit to be modified is selected and starts blinking when the up and
Down/Up
down keys are pressed. (These keys are managed in the same way as a
drum. This means that on reaching one end of the variable field, you go back
to the other end.)
z Next, when the left and right keys are pressed, the digit values are displayed
in one direction or the other (these keys are also managed in the same way
as a drum).
33003962 11/2011
135
Communication with the Automation System
Edition
Methods
Key
Description
Direct Edition
(XBT R4•• only):
Key F1 to F12
Keys F1 to F12 are dual labelled Fx/Nx (function/numeric) keys. They can be
used to modify values directly. The correspondence between keys and numeric
values is as follows:
Key
Value
F1
1
F2
2
F3
3
F4
4
F5
5
F6
6
F7
7
F8
8
F9
9
F10
0
F11
+/-
F12
.
Virtual numeric keypad on
Direct Input via
touchscreen of XBT RT:
Virtual numeric
Keypad (XBT RT
in touch variant
only):
136
Activate the individual buttons on the touchscreen with your
finger to enter the respective character.
33003962 11/2011
Communication with the Automation System
Confirming / Cancelling an Edition
Overview
To confirm or to cancel the edition of alphanumeric fields, use the ENTER and ESC
key.
Confirming an Edition
ENTER key
If you press the ENTER key after you have modified an edition field, the entered
value is transmitted to the connected device. Refreshment of the field, which was in
edition mode, is active again.
Canceling an Edition
ESC key
If you press the ESC key after you have modified an edition field, the following will
happen:
z
z
z
33003962 11/2011
No write action is performed to the automation system.
The value prior to edition is redisplayed.
Refreshment of the field, which was in edition mode, is active again.
137
Communication with the Automation System
Exit Edition on Time Out
Overview
If you have enabled edition mode but you do not press any key for more than 1
minute, edition mode will be disabled automatically and the following will happen:
z
z
138
No write action is performed to the automation system.
Refreshment of the field, which was in edition mode, is active again.
33003962 11/2011
Communication with the Automation System
Edition Report
Overview
After the edition mode has been disabled, the connected equipment is informed of
how the edition ended:
z
z
z
confirmation
cancellation
time out
by updating the Report word in the dialog table.
33003962 11/2011
139
Communication with the Automation System
11.4
Handling Alarms
Overview
This section describes how to view, ignore and print alarms.
Please note that these functions are not available for XBT N200 terminals.
What’s in this Section?
This section contains the following topics:
Topic
140
Page
Viewing or Ignoring Alarms
141
Alarm Log
143
33003962 11/2011
Communication with the Automation System
Viewing or Ignoring Alarms
Overview
When an alarm occurs, it is automatically displayed on the display unit.
An alarm is displayed blinking
You can now view and acknowledge the alarm or you can ignore the alarm.
Viewing Alarms
To view the alarm, use the keys of your XBT terminal as described below:
Key
Description
Scroll through the alarm panel (up to 25 lines).
Scroll through the list of alarm panels.
Press the ENTER key to acknowledge the alarm on the display. The alarm
message stops blinking and changes to a steady display.
Press the ESC key to exit viewing alarm panels.
33003962 11/2011
141
Communication with the Automation System
Example
Using the left and right arrow keys to scroll through the alarm list:
Ignoring Alarms
To ignore an actual alarm, use the ESC as described below
Key
Description
If an alarm is displayed during operation, you can press the ESC key to
return to operating mode. The alarm remains in the list and the ALARM
LED changes to a steady display.
142
33003962 11/2011
Communication with the Automation System
Alarm Log
Log Principles
Alarms are automatically stored in a log file one after another. Once the log file is
full, new alarms overwrite the oldest alarms. In this way each alarm event (for
appearance, acknowledgment, disappearance see Listing Alarms in Operating
Mode (see page 105)) is recorded and time-stamped.
NOTE: XBT R411 and XBT RT511 are the only terminals that save a log. The
retention period for the log is limited to twelve hours. After that time the log may be
cleared. Any other XBT terminal types loose the information stored in the log as
soon as they are switched off.
NOTE: To store an alarm panel in the log, the store option must be enabled for the
panel.
You can view, clear and print the log which will be described in the following
sections.
Viewing the Log
You can access the alarm log from the MENU system panel (see Displaying System
Panels (see page 110)).
MENU system panel
Once inside the log, you can browse through the various alarms (see Viewing
Alarms (see page 141)).
Clearing the Log
To clear the log file proceed as follows:
Step
33003962 11/2011
Action
1
In the MENU system panel select ALARMS LOG.
2
In the following panel select CLEAR.
Result: The alarm log is empty.
143
Communication with the Automation System
11.5
Printing Alarms
Overview
This section provides a general overview of the printing function for alarms.
Please note that this function is only available for XBT N401, XBT R411 and
XBT RT511 terminals.
What’s in this Section?
This section contains the following topics:
Topic
144
Page
Principles of Printing Alarms
145
Printing Alarms as a Data Stream
146
Printing the Alarm Log
147
33003962 11/2011
Communication with the Automation System
Principles of Printing Alarms
Overview
You can print alarms in the following different ways that will be described in the
following sections:
z
z
z
33003962 11/2011
printing alarms as a data stream
printing the alarm log
printing the list of current alarms
145
Communication with the Automation System
Printing Alarms as a Data Stream
Overview
The alarm name and status are printed whenever an alarm status changes.
The following information are printed:
z
z
z
z
z
alarm number
name of the alarm panel
print date
print time
alarm status
NOTE: In order for an alarm panel to be printed, the print option must be enabled for
the panel .
Example
Alarm 1 appeared, was acknowledged and then disappeared.
Alarm 2 is present but has not been acknowledged.
146
33003962 11/2011
Communication with the Automation System
Printing the Alarm Log
Initiated by the Operator
The log is printed in sequential order (sorted by status), with the most recent alarm
at the top.
The following information is printed for each alarm:
z
z
z
z
z
its number
name of the alarm panel
date and time of appearance
date and time of acknowledgment
date and time of disappearance
Initiated by the PLC
The log is printed by means of the print command word in the dialog table.
The log is printed in sequential order (sorted by status), with the most recent alarm
at the top.
The following information is printed for each alarm:
z
z
z
z
z
alarm number
name of the alarm panel
date and time of appearance
date and time of acknowledgment
date and time of disappearance
Example
Alarm 1 appeared, was acknowledged and then disappeared.
Alarm 2 is present but has not been acknowledged.
33003962 11/2011
147
Communication with the Automation System
148
33003962 11/2011
Magelis XBT N/R/RT
Vijeo-Designer Lite Configuration Software
33003962 11/2011
Vijeo-Designer Lite Configuration
Software
12
Overview
This chapter provides a short reference to the Vijeo-Designer Lite configuration
software for XBT terminals.
What’s in this Chapter?
This chapter contains the following topics:
Topic
33003962 11/2011
Page
Creating XBT Terminal Applications
150
Exchanging Data with the Automation System via the Dialog Table
151
149
Vijeo-Designer Lite Configuration Software
Creating XBT Terminal Applications
Criteria
An XBT terminal application consists of the entire dialog between the operator and
the automated process. In its entirety, this should take account of:
The criteria relating to the
automation system:
The user criteria:
The criteria for creating the actual
dialog application:
z
z
z
z
z user interface
z level of intervention
z programming
z debugging
z upgrading
production monitoring
preventive maintenance
corrective maintenance
process control
NOTE: These constraints mean that it is necessary to structure your application. An
application should consist of a set of panels that can be arranged in a tree structure.
Example of a Panel Tree Structure
Tree structure
150
33003962 11/2011
Vijeo-Designer Lite Configuration Software
Exchanging Data with the Automation System via the Dialog Table
Overview
Dialog tables are integrated in the PLCs that are connected to XBT terminals.
A dialog table is a set of data exchanged between the PLC and the XBT terminal.
Dialog tables are used to inform terminals of alarm states.
For more information on the data exchange between XBT terminals and connected
equipment via dialog tables refer to the Vijeo-Designer Lite online help.
33003962 11/2011
151
Vijeo-Designer Lite Configuration Software
152
33003962 11/2011
Magelis XBT N/R/RT
33003962 11/2011
Appendices
Overview
This part provides additional information on this manual.
What’s in this Appendix?
The appendix contains the following chapters:
Chapter
33003962 11/2011
Chapter Name
Page
A
Troubleshooting and Further Information
155
B
Architectures of Automation Systems
163
153
154
33003962 11/2011
Magelis XBT N/R/RT
Troubleshooting and Further Information
33003962 11/2011
Troubleshooting and Further
Information
A
Overview
This chapter provides additional information about troubleshooting, alert messages,
internal variables and self-tests of the terminals.
What’s in this Chapter?
This chapter contains the following topics:
Topic
33003962 11/2011
Page
Troubleshooting
156
System Messages
158
Internal Variables
160
Terminal Self-Tests
162
155
Troubleshooting and Further Information
Troubleshooting
Overview
Condition
Cause
Remedy
????? displayed rather
than any values
The transmission parameters set in the
Vijeo-Designer Lite software for the
protocol you are using for communication
are not configured correctly.
Check the transmission parameters in the
dialog box of the Vijeo-Designer Lite
software for the protocol you are using.
For more detailed information refer to the
user manual of this protocol.
No memory allocation for this variable has Allocate memory space for the variable
been declared in the PLC
Cannot read dialog
table message displayed
on terminal
The equipment declared for the variable
does not exist
Modify the list of equipment and check the
declared addresses
The equipment is not connected to the
terminal
Check the connection
The equipment is connected to the
terminal via an XBT Z978 cable
Check the connection. Try using an
XBT Z9780 cable
The equipment is connected to the
terminal via an XBT Z9780 cable
Check the connection. Try using an
XBT Z978 cable (equivalent to an
XBT Z9780 cable equipped with an
XBT ZN999 adaptor).
The equipment declared for the dialog
table does not exist
Modify the list of equipment and check the
declared addresses
No memory allocation for the dialog table Allocate memory space for the dialog
has been declared in the PLC
table in the PLC (e.g., %MW100 to
%MW125)
The equipment is not connected to the
terminal
Check the connection
Incorrect dialog table
authorization message
The value of the authorization word
stored in the PLC is not correct
Using Vijeo-Designer Lite, check the
expected value (\Configuration\Dialog
Table) for the Authorization Table and its
location in the memory equipment
Product seems to be not
powered (backlight not on
and nothing displayed on
the display unit
XBT N401/NU400: No 24 V power supply Check the power supply
156
XBT N200/400:
z No power supply via the PC mouse
port.
z Dialog table forces the back-light to
remain off.
z No power supply via the PLC
communication port in run mode.
Check whether the PC mouse port has
been activated (see PC Control Panel),
check the PLC program. Check whether
the cable is connected to the PLC port.
Check that power is being supplied to the
PLC.
33003962 11/2011
Troubleshooting and Further Information
Condition
Cause
Remedy
Cannot read/write variable
message
The equipment declared for the variable
does not exist
Check the addresses declared for the
equipment
The variable does not have a valid
address in the declared device
Check the variable address
The equipment is not connected to the
terminal
Check the connection
Import impossible XBT-->
PC
Application protected by password
Ask the creator of the application for the
password
Inoperative keys
Locked by the dialog table
Check the PLC program
Incorrect terminal configuration
Check that the terminal configuration is
correct for input or control or touch variant
No application message
No application
Transfer an application
No printing
No connection
Connect the cable and check that it is
connected correctly at both ends. Then
check that the printer is switched on.
The cable connecting the printer to the
terminal is incorrect
Check that the cable is the appropriate
type
Incorrect printer configuration
Refer to the printer manual to check that
the configuration saved by the terminal is
the same as the current configuration
Every other line is printed
The terminal is configured as LF rather
than auto-LF
Abnormal printing
Lines are printing one on top of the other. The terminal is configured as auto-LF
rather than LF
33003962 11/2011
157
Troubleshooting and Further Information
System Messages
Single-Language System Messages
System messages generated by the XBT (single-language system messages:
English), non-configurable.
System Message
Description
APPLICATION FAULT:
Application inconsistency.
AUTOTEST IN PROGRESS:
Autotests running.
BIOS ERROR # x CS:x IP:x:
Critical BIOS issue, consult Schneider Electric.
CHECKSUM FAILED:
Firmware checking result.
DOWNLOAD ABORTED:
Download to the XBT canceled by the operator. Redo a
download.
DOWNLOAD COMPLETED:
Download to the XBT finished.
DOWNLOAD FAILED:
Download to the XBT not completed.
DOWNLOAD IN PROGRESS:
Download to the XBT in progress.
FPU ERROR # function x:
Critical math libraries result, consult Schneider Electric.
INCORRECT TERMINAL TYPE IN .DOP FILE:
Application is exported to a terminal type X when it had
been created for a terminal type Y.
KERNEL TRAP #x ES:x IP:x:
Critical real-time kernel result, consult Schneider
Electric.
NO APPLICATION:
Product has no application.
PROCESSOR TRAP # x CS:x IP:x:
Critical terminal result, consult Schneider Electric.
RUNTIME ERROR # x CS:x IP:x:
Critical RUNTIME result, consult Schneider Electric.
SWITCH POWER OFF CS:x IP:x:
Critical terminal result, consult Schneider Electric.
UPLOAD ABORTED:
Upload to the PC canceled by the operator.
UPLOAD COMPLETED:
Upload to the PC finished.
UPLOAD FAILED:
Upload to the PC not completed.
UPLOAD IN PROGRESS:
Upload to the PC in progress.
WAITING FOR TRANSFER:
Awaiting remote loading.
WIRING FAULT:
Wiring problem.
Multi- Languages System Messages
XBT system messages (6 languages), which can be translated by Vijeo-Designer
Lite in the system panels.
158
33003962 11/2011
Troubleshooting and Further Information
Number
System Message
Description
#244
ALARM LIST EMPTY:
No alarms logged in the terminal.
#203
CANNOT READ DIALOG TABLE:
Connection problems between XBT <-> PLC.
#241
CANNOT READ VARIABLE:
Variable cannot be read.
#202
CANNOT WRITE DIALOG TABLE:
Writing to a protected zone or XBT <-> PLC connection
problems.
#242
CANNOT WRITE VARIABLE:
Variable cannot be written.
#204
CONNECTION IN PROGRESS:
XBT is trying to connect to the PLC.
#247
DATE FORMAT INVALID:
The date cannot be displayed because of its format.
#201
DIALOG TABLE AUTHORIZATION:
Authorization word is incorrect.
#251
LANGUAGE DOES NOT EXIST:
Language not entered in the XBT.
#250
LANGUAGE IMPOSED BY THE PLC:
Current language determined by the PLC.
#257
LOG CLEARING IN PROGRESS:
Following an operator request, the log is being cleared.
#243
OVERFLOW MIN <= VALUE <= MAX:
Input of a value, which is outside the limits.
#249
PAGE DOES NOT EXIST:
Call-up of a non-existent page.
#253
PASSWORD IMPOSED BY THE PLC:
Current password determined by the PLC.
#258
PRINTING STOPPED BY USER:
The operator sent a request to stop the current print job. The
next job in the print buffer will be printed as soon as the end
of the line in the first print job is reached.
#255
PRINT RECOGNISED:
The print request sent by the operator has been accepted
and placed in the processing buffer: it will be processed as
soon as the current print job is completed.
#254
PROTECTED ACCESS PAGE:
Call-up of a page protected by password.
#256
REFUSED: PRINTING IS ALREADY IN
PROGRESS:
The same print request was sent twice in succession by the
operator before the first print request could be fulfilled. The
request is rejected.
#246
TIME FORMAT INVALID:
The time cannot be displayed because of its format.
#248
WRONG PASSWORD:
Input of an incorrect password.
33003962 11/2011
159
Troubleshooting and Further Information
Internal Variables
Purpose
XBT terminals provides internal variables you can use to display information on your
panels or to control your terminal.
List of the Internal Variables
160
Variable
Type
Description
%MW0...
%MW299
All
Buffer (This variable is only available in Modbus Slave
applications.)
%MW50000
Word
Date in ASCII
%MW50001
Word
Time in ASCII
%MW50002
Word
Seconds (0 to 59)
%MW50003
Word
Minutes (0 to 59)
%MW50004
Word
Hour
%MW50010 to
%MW50056
Word
Free words
%MW50057
Word
Quick increment from 0 to 65535
%MW50058
Word
Quick decrement from 65535 to 0
%MW50059
Word
Increment from 0 to 9 every 2 seconds
%MW50060
Word
Decrement from 9 to 0 every 2 seconds
%MW10000
Word
Transmission speed
%MW10001
Word
Parity
%MW10005
Word
Address number
%MW10006,0
Bit
Counters reset
%MW10007...
%MW10015
Word
Counters 1...9 (value depending on the protocol)
%MW10026
Word
Mute all buzzer output
%MW10028
Word
Value of the programmed language
%MW10033
String
Password level in progress
%MW10034
String
Password input in progress
%MW10035
Word
Reset current password value (=0 for Reset).
%MW10036
String
Product reference
%MW10037
String
Application name
%MW10038
String
Date of the last application backup
%MW10039
String
Time of the last application backup
33003962 11/2011
Troubleshooting and Further Information
Variable
33003962 11/2011
Type
Description
%MW10040
String
Protocol name
%MW10041
String
Build time version
%MW10042
String
Firmware version
%MW10043
String
Run time name
%MW10044
String
Run time version
%MW10050...
%MW10059
Word
Counter 10...19 (value depending on the protocol)
%MW11000
Word
Value of the panel to be displayed
%MW12000
Word
Values >0 clear the history
%MW12001
Word
Values >0 print the history
%MW12020
Word
Values >0 print the alarm list
%MW12030
Word
Values >0 stop the printing process
%MW60023
Word
Acknowlegment of all alarms
161
Troubleshooting and Further Information
Terminal Self-Tests
Overview
XBT terminals perform 2 types of self-tests:
z
z
self-test during power-up
continuous self-test during operation
Self-Test Power-Up
When the terminal is powered up, the following self-tests are performed:
Element Tested
Test Principle
Non-passing Result Criterion Action in Event of Non-Passing
The working memory Writing/reading
(RAM)
Value read different from value Operation impossible: STOP
written
The firmware
Checksum calculation
and checking
Calculated checksum <>
stored checksum
Operation impossible: STOP
The application
memory
Checksum calculation
and checking
Calculated checksum <>
stored checksum
Operation impossible: Transfer
compulsory
Continuous Self-Test
A continuous self-test checks that the program is operating correctly (watchdog).
NOTE: If a problem is detected that prevents operation of the product, the terminal
turns off all its LEDs, stops working and displays a system message number (if the
detected condition permits it to do so). If the same problem still persists after the
terminal has been switched back on, inform the maintenance department of this
system message number.
162
33003962 11/2011
Magelis XBT N/R/RT
Architectures of Automation Systems
33003962 11/2011
Architectures of Automation
Systems
B
Types of Architectures of Automation Systems
Communication via Protocols
Communication between the XBT terminal and connected equipment is achieved by
means of a communication protocol, which is selected when creating the application
in Vijeo-Designer Lite.
The protocols available for the XBT range support communication with the
Schneider range of PLCs, specific equipment (speed drives) and third party PLCs.
Supported protocols are Uni-Telway, Modbus (master and slave), Siemens PPI,
AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY. Please note that not all XBT
types support all protocols.
The following types of architecture are possible, which enable 1 XBT terminal to be
linked to several equipment or several XBT terminals to 1 equipment:
z point-to-point connections
z multipoint connections
z multidrop connections
For more information on the protocols, please refer to the Protocols User Manuals.
Point-to-Point Connection (all XBT terminals)
1 XBT terminal linked to 1 equipment.
33003962 11/2011
163
Architectures of Automation Systems
Protocols:
z Modbus master
z Uni-Telway slave
z Siemens PPI (*)
z AB DF1 (*)
z AB DH485 (*)
z Mitsubishi FX (*)
z SYSMAC-WAY (*)
z Zelio (**)
z Millenium (**)
(*) XBT N200/N400/R400 do not support these protocols.
(**) Zelio is supported only by the XBT N401, XBT R411 and XBT RT511.
(**) Millenium is supported only by the XBT N401, XBT R411 and XBT RT511.
Multipoint Connection (XBT N401 / N410 / NU400 / R410 / R411 / RT511)
1 XBT terminal linked to several equipment (maximum of 15).
Protocols:
z Modbus master
z Uni-Telway slave
z Siemens PPI
z AB DF1
z AB DH485
z Mitsubishi FX
z SYSMAC-WAY
164
33003962 11/2011
Architectures of Automation Systems
Multidrop Connection (XBT N401 / N410 / R410 / R411 / RT511)
Several XBT terminals linked to 1 equipment.
Protocols:
z Modbus slave
z Uni-Telway
33003962 11/2011
165
Architectures of Automation Systems
166
33003962 11/2011
Magelis XBT N/R/RT
Glossary
33003962 11/2011
Glossary
A
alarm panel
Information panel displayed when an alarm occurs on the automation system.
An alarm panel is displayed by the automation system, when the associated boolean
variable changes.
It is generally used to provide to the operator all the information and the description
of the actions he has to do, in order to deal with the current alarm.
alarm table
An alarm table is a communication table that contains only words related to alarm
functions.
Each bit of alarm words can be associated to an alarm.
The equipment can use it to signal to the terminal that an alarm has occurred.
The terminal can use the status words of the alarm table to report to the equipment
that the operator has acknowledged an alarm.
alphanumeric
characters (A-Z) and numbers (0-9)
alphanumeric display units
These are only capable of displaying characters (with a font resolution usually 5x7
pixels). The characters are physically separated from one another.
33003962 11/2011
167
Glossary
alphanumeric terminals
These are equipped with alphanumeric display units or matrix display units used in
character mode only.
animated HMI object
Object which representation and behavior depends on operator actions or on
variables belonging to an equipment or to the terminal.
application
Please refer to HMI application.
application browser
Structure tree representing the HMI application. The application bar is located at the
left of the Vijeo Designer Lite user interface.
application panel
An application panel can be displayed either by the operator or by the equipment of
the automation system.
It can display any information about the automation system.
It allows the operator to input data into the automation system and to navigate from
one panel to others.
automation system
all components (e.g. PLCs, HMI terminals, sensors, actuators) of an automated
process
B
bitmap
Image with fixed dimensions, which can be handled by a Windows software.
button
Windows object used to perform the action described by the label or the symbol it
contains
A button is validated on touch screen or by pressing the enter key while the button
is selected.
168
33003962 11/2011
Glossary
C
command table
Part of the dialog table completed by the control system. This word list contains all
the instructions passed to the terminal.
communication table
generic word for either a dialog table or an alarm table
configuration software
Vijeo Designer Lite is the configuration software that allows to create a HMI
application and transfer it between a terminal and an equipment.
current language
The language of the HMI application the designer is working on.
D
default terminal language
The HMI language used by the terminal when it is powered on.
demo version
Version of Vijeo-Designer Lite used to demonstrate the configuration software.This
version does not allow any transfer of the HMI application between the VijeoDesigner Lite software and an XBT terminal.
designer
Please refer to HMI designer.
dialog application
Set of data, necessary and sufficient to describe the behavior of a terminal during
operation. Vijeo Designer Lite is the only tool that can be used to create this type of
application for Schneider Electric terminals.
33003962 11/2011
169
Glossary
dialog table
A dialog table is a communication table that can contain words related to any
function of the terminal.
A dialog table can include an alarm table.
The purpose of a dialog table is to exchange data or orders between the terminal
and the connected equipment.
download
Transfer of an HMI application from an XBT terminal to Vijeo-Designer Lite.
dynamic function keys
These keys are placed on the front face of a terminal and their behavior depends on
the displayed panel.You can set different function to them (e.g. panel access,
command functions, object selection).
E
equipment
Any device (generally a PLC) which communicates with a terminal.
external variable
Variable which belongs to an equipment.
F
firmware
This is the terminal on-board software. It comprises mainly the BIOS and the loader
used to communicate with Vijeo-Designer Lite.
H
HMI
human machine interface
170
33003962 11/2011
Glossary
HMI application
Names all the data necessary to describe the behavior of an HMI terminal in the
operating mode.
Vijeo Designer Lite is the configuration software that allows to create an
HMI application.
HMI designer (or designer)
The person who designs an HMI application using Vijeo Designer Lite.
Even if there is no particular training to use Vijeo-Designer Lite, some skills in
process automation are recommended to create a application.
HMI language
An HMI application can be designed in several different languages. Each of these
languages is an HMI language.
HMI object (or object)
The smallest element contained in a panel. Can be either an animated or an notanimated HMI object.
HMI operator (or operator)
The person who uses an HMI terminal in operation mode, in order to control and lead
an automated installation or machine.
An operator is a person who does not have any specific skill in process automation
or computer science.
HMI terminal (or terminal)
Electronic terminal used by operators to control an automation system.
An HMI terminal is mainly used to display information and alarms from the
automation system, to allow the operator to input some parameter values into the
automation system, and to control it.
Basically, a terminal replaces former control panels that were mainly made of push
buttons, lamps, indicators and measurement devices.
I
internal variable
Variable which belongs to the terminal.
33003962 11/2011
171
Glossary
Some internal variables provide services (like date/time) that can be used by the
HMI designer without any restriction, as if they were PLC/equipment variables.
L
link
HMI object contained in a panel used to access application panels or system panels
(navigation links) or to perform command functions (command links).
loader
Part of terminal firmware responsible for handling communication with
Vijeo Designer Lite to transfer a application in one direction or the other. Its role is
also to store application data, sent by Vijeo Designer Lite, in the terminal memory.
M
Magelis
Generic commercial name of the all range of Schneider HMI terminals.
matrix display units
These consist of a continuous matrix of pixels, enabling the display of characters in
different fonts and sizes, and also basic graphics. The technology and resolution of
these display units is, however, too low for them to be considered true graphic
display units.
matrix touch screen (or touch screen)
Transparent sheet stuck on a display, composed of a matrix of areas and sensible
to operator action on it.
menu
Title, located in a menu bar, allowing by selection to access a list of menu items.
Each of these menu items is associated with a function.
mode of operation
There are 2 modes of operation:
z operating mode
z transfer mode
172
33003962 11/2011
Glossary
N
not-animated HMI object
Object which representation is constant. It is always displayed exactly as it has been
configured.
O
object
Please refer to HMI object.
operating mode
A terminal´s mode of operation in which the terminal communicates with one or
several equipment of an automation system.
This is the normal operating mode of a terminal, when it uses the HMI application.
The operator generally uses the terminal in this operating mode. Please refer to
transfer mode.
operator
Please refer to HMI operator.
optimum version
Version of a terminal that can only be connected to some of the Schneider PLCs.
Main characteristics:
z just enough features
z external 5 VDC power supply (mainly provided by the PLC)
z 1back-light color
P
panel
A terminal can display a panel. Its size can be larger than the terminal display. In this
case, the terminal allows using the scrolling to move the visible part of the panel.
A panel can contain not-animated objects (e.g. background images, static texts) and
animated objects (e.g. value displays, bar graphs).
33003962 11/2011
173
Glossary
There are 3 different types of panels:
z application panel
z alarm panel
z system panel
panel editor
The panel editor displays the panel in WYSIWYG format (what you see is what you
get). If the panel can not be displayed completely in the editor, a scroll bar is
displayed.
pilot device
A terminal can communicate with several control system-devices. Of these, only one
is able to send commands to the terminal, and is capable of knowing its status; this
device is called the pilot device. It contains the dialog table.
PLC
programmable logic controller
protocol
language of the communication between a terminal and equipment(s) connected to
an industrial network
R
reference language
Language in which the designer constructs his application panels. By default, it is
the installation language of the Vijeo-Designer Lite programming software.
S
service keys
Keys on the keypad necessary for certain terminal functions (scrolling, selecting
fields, data input, requesting a menu, etc.).
standard version
Version of a terminal with standard functionality.
174
33003962 11/2011
Glossary
Main characteristics:
z external 24 VDC power supply
z point to point and multi-point connection
z 1 back-light color
static function keys
Keys placed on the front face of a terminal.
Their behavior is the same for the whole application.
You can set different functions to them (e.g. panel access, command functions).
status bar
Zone located at the bottom of a Windows window. It is used to indicate the state of
the application or active element to the developer.
status table
Part of the dialog table completed by the terminal. This word list represents the
terminal status.
system panel
A system panel is a pre-built, ready to use panel, which is systematically embedded
into an HMI application.
A system panel can be displayed either by the operator or by the equipment of the
automation system, or by the terminal itself.
It informs the operator about system or automation errors by a system popup panel.
It allows the operator to change some terminal parameters (e.g. date,
HMI language) and to navigate from one panel to others.
T
terminal
Please refer to HMI terminal.
third party
Indicates the fact that it is not a Schneider product.
As an example it can be used for:
z third party protocol
z third party PLC
33003962 11/2011
175
Glossary
thumbwheel edition
Rudimentary edition mode based on the same principle as mechanical
thumbwheels: selection of the digit to be modified by means of the horizontal arrow
key(s), then selection of the digit value by means of the vertical arrow key(s).
touch screen
Please refer to matrix touch screen.
transfer mode
A terminal´s specific mode of operation in which the terminal is able to communicate
with the configuration software to transfer an HMI application.
The HMI designer mainly uses the terminal in this mode of operation. Please refer
to operating mode.
tree structure
Structure representing the application panels and the links between them. By
extension, this window is used to represent the structure of all types of panels.
U
universal version
Version of a terminal that can be connected to Schneider and third party PLCs in
point to point as well as multi-point.
Main characteristics:
external 24 VDC power supply
z point to point and multi-point connection
z light indicators
z 3 back-light colors
z peripheral connection (printer)
z
upload
Transfer of an HMI application from Vijeo-Designer Lite software to an XBT terminal.
user
Either an operator or a designer (when it is not necessary to make the distinction).
176
33003962 11/2011
Glossary
V
variable
Storage element containing a value evolving during the time. Can be either a internal
variable or an external variable.
variable field
Area on a panel configured to display an item depending on the value of a variable
in the connected equipment.
version
There are 3 terminal versions:
z please refer to optimum version
z please refer to standard version
z please refer to universal version
Vijeo-Designer Lite
Configuration software for the low end Magelis range. It replaces the XBT-L1000
software.
W
WYSIWYG
What You See Is What You Get.
X
XBT
Any HMI terminal (when it is not necessary to make the distinction).
33003962 11/2011
177
Glossary
178
33003962 11/2011
Magelis XBT N/R/RT
Index
33003962 11/2011
B
AC
Index
Specials
A
alarm
buzzer, 107
alarm list, 106, 107, 107
alarm log, 108, 143
clearing, 143
display, 143
principles, 143
alarm management, 106
alarm panels, 141
acknowledgment, 107
advantages in operating mode, 105
appearance types, 106
display, 108
display priority, 106
displaying, 141
ignoring alarms, 142
log, 108, 143
objective, 105
principle, 105
principles, 105
storage principle, 107
viewing, 141, 141
alarms
objective, 105
appearance types, 106
application, 150
33003962 11/2011
application panels
definition, 100
display, 101
principle, 100
applications, 83
automation system architectures
mulitipoint connection, 164
multidrop connection, 165
point-to-point connection, 163
B
blank labels, 53
button object, 126
C
cable, 93
cabling, 62
cancelling an edition, 137
characteristics, 18, 19
commands
impulse, 123
toggle, 124
confirming an edition, 137
connection
multidrop, 165
multipoint, 164
to a PC, 62
connectors, 32
control elements, 28
controlling automation system, 97
179
Index
D
date and time, 116
display format, 116
input, 116
dialog table
exchanging data via, 151
display of a panel, 101
display of an application panel
on power up, 101
dual labelled keys, 87
dynamic function keys, 126
E
edition
cancellation, 137
confirmed, 137
report, 139
environmental influences, 18
exchanging data via the dialog table, 151
F
function keys
dynamic, 34
static, 34
functional command link
representation, 128
functional link, 126
functions
of keys, 87
of touchscreen, 87
XBT terminals, 82
H
HMI language selection, 115
human/machine dialog, 83
I
impulse commands, 123
180
input
exit on time out, 138
of a value, 135
input/modification of a value, 133
insert label XBT N, 42
insert label XBT R, 44
insert label XBT RT, 46
K
key functions, 87
keys, 28, 34
L
label
insert label XBT N, 42
insert label XBT R, 44
insert label XBT RT, 46
language, 115
LED
communication, 93
LED functions, 90
LEDs, 28
line parameters, 118
error counters, 118
log file, 143
M
managing alarms, 106
material, 18
MiniDIN, 32
mode of operation
selection, 94
modes of operation
operating mode, 93, 109
transfer mode, 93, 96
mounting, 18
O
operating elements, 28
operating mode, 93, 97
33003962 11/2011
Index
operation mode
selection, 94
P
panels, 28
password-protection, 119
PC
connection to PC, 62
PLC architectures, 163
polling times, 25
printing, 145
alarm log, 147
as a data stream, 146
principles, 145
printing blank labels, 53
process commands
via function keys, 131
via functional links, 126
product reference, 117
protecting the terminal, 119
protocols, 163
terminal self-test, 162
continuous, 162
on power-up, 162
time out
input mode, 138
toggle commands, 124
touchscreen functions, 87
transfer mode, 96
transferring software applications, 95
W
word
report, 139
X
XBT NU400
polling times, 25
R
RJ45, 32
S
scrolling within panels, 111
selecting an edition field, 133
by the operator, 133
by the pilot equipment, 134
selecting mode of operation, 94
setting the display parameters, 114
standards, 18
structure of XBT applications, 83
SubD25, 32
system panels, 109, 110
definition, 109
principle, 109
T
temperature, 18
33003962 11/2011
181
Index
182
33003962 11/2011
">