Schneider Electric XBTN/R/RT, Compact Display Units User manual
PDF
Documento
Anúncio
Anúncio
Magelis XBT N/R/RT 33003962 11/2011 Magelis XBT N/R/RT Compact Display Units User Manual 33003962.03 11/2011 www.schneider-electric.com The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us. No part of this document may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission of Schneider Electric. All pertinent state, regional, and local safety regulations must be observed when installing and using this product. For reasons of safety and to help ensure compliance with documented system data, only the manufacturer should perform repairs to components. When devices are used for applications with technical safety requirements, the relevant instructions must be followed. Failure to use Schneider Electric software or approved software with our hardware products may result in injury, harm, or improper operating results. Failure to observe this information can result in injury or equipment damage. © 2011 Schneider Electric. All rights reserved. 2 33003962 11/2011 Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standards and General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . Chapter 3 Characteristics of the XBT Terminal Range. . . . . . . . . . 3.1 Characteristics of the XBT Terminal Range . . . . . . . . . . . . . . . . . . . . . . . Characteristics Applying to All XBT Terminals . . . . . . . . . . . . . . . . . . . . . Characteristics of the Individual XBT Terminals . . . . . . . . . . . . . . . . . . . . Polling Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 4 Operating Elements, LEDs and Connectors . . . . . . . . . 4.1 Operating Elements, LEDs and Connectors . . . . . . . . . . . . . . . . . . . . . . . Front Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview of Keys on the Individual XBT Terminals . . . . . . . . . . . . . . . . . Chapter 5 Insert Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Insert Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Insert Labels XBT N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Insert Labels XBT R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Insert Labels XBT RT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 6 Inserting Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting Insert Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 7 Creating Individual Labels . . . . . . . . . . . . . . . . . . . . . . . . Creating Individual Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 8 Connecting XBT Terminals . . . . . . . . . . . . . . . . . . . . . . . 8.1 Grounding and Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Information Concerning the Grounding of Terminals . . . . . . . . . . . 33003962 11/2011 7 9 11 11 13 13 17 17 18 19 25 27 27 28 32 34 41 41 42 44 46 49 49 53 53 57 58 58 3 8.2 Connecting XBT Terminals to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Distinguishing XBT Terminals by Power Supply . . . . . . . . . . . . . . . . . . . Connecting XBT Terminals Powered by the PLC to a PC . . . . . . . . . . . . Connecting XBT Terminals Powered by an External Power Supply to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Connecting XBT Terminals to a PLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . Distinguishing XBT Terminals by Power Supply . . . . . . . . . . . . . . . . . . . Connecting XBT Terminals Powered by the PLC to a PLC . . . . . . . . . . . Connecting XBT Terminals Powered by an External Power Supply to a PLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4 Connecting XBT N401 / R411 / RT511 Terminals to a Printer . . . . . . . . Printer Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 68 69 71 Chapter 9 Overview of Applications and Functions . . . . . . . . . . . . 81 9.1 Overview of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview of XBT Terminal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 XBT Terminals in HMI Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HMI Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 Functions of Keys, Touchscreen, LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . Functions of Keys and Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functions of LEDs on XBT N401 / XBT R411 / XBT RT511 Terminals. . 82 82 83 83 86 87 90 Chapter 10 Operating Principles of XBT Terminals . . . . . . . . . . . . . . 91 10.1 10.2 10.3 10.4 4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic Selection of the Mode of Operation . . . . . . . . . . . . . . . . . . . . Transfer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Panel Structure of XBT Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Principle of Application Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Displaying Application Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Principle of Alarm Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alarm Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Principle of System Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Displaying System Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scrolling within Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing Configuration Parameters via the System Panel SYSTEM . . Selecting the HMI Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selecting the Date and Time Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing the Product Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing the Line Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Password-Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing Password-Protected Panels, Fields, Functional Links . . . . . . 60 61 62 75 80 80 92 93 94 95 97 99 100 101 105 106 109 110 111 113 114 115 116 117 118 119 119 33003962 11/2011 Chapter 11 Communication Between XBT Terminals and the Automation System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 Types of Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Impulse Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toggle Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 Activating Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Activating Commands via Functional Links, Button Objects or Dynamic Function Keys on the Display Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Activating Commands via Function Keys on the Display Unit. . . . . . . . . . 11.3 Entering / Modifying Values Alphanumeric Fields in Edition Mode . . . . . . Accessing an Alphanumeric Edition Field . . . . . . . . . . . . . . . . . . . . . . . . . Entering a Value in an Edition Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Confirming / Cancelling an Edition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exit Edition on Time Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Edition Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4 Handling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viewing or Ignoring Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5 Printing Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Principles of Printing Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing Alarms as a Data Stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing the Alarm Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 12 Vijeo-Designer Lite Configuration Software . . . . . . . . . 121 122 123 124 125 126 131 132 133 135 137 138 139 140 141 143 144 145 146 147 149 Creating XBT Terminal Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exchanging Data with the Automation System via the Dialog Table. . . . . 150 151 Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Appendix A Troubleshooting and Further Information . . . . . . . . . . . 155 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Terminal Self-Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix B Architectures of Automation Systems . . . . . . . . . . . . . . 156 158 160 162 163 Types of Architectures of Automation Systems. . . . . . . . . . . . . . . . . . . . . 163 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 179 33003962 11/2011 5 6 33003962 11/2011 Safety Information § Important Information NOTICE Read these instructions carefully, and look at the equipment to become familiar with the device before trying to install, operate, or maintain it. The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. 33003962 11/2011 7 PLEASE NOTE Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. A qualified person is one who has skills and knowledge related to the construction and operation of electrical equipment and its installation, and has received safety training to recognize and avoid the hazards involved. 8 33003962 11/2011 About the Book At a Glance Document Scope This manual describes how to use the Magelis XBT N/R/RT device. Validity Note The technical characteristics of the device(s) described in this manual also appear online. To access this information online: Step Action 1 Go to the Schneider Electric home page www.schneider-electric.com. 2 In the Search box type the model number of a product or the name of a product range. z Do not include blank spaces in the model number/product range. z To get information on a grouping similar modules, use asterisks (*). 3 If you entered a model number, go to the Product datasheets search results and click on the model number that interests you. If you entered the name of a product range, go to the Product Ranges search results and click on the product range that interests you. 4 If more than one model number appears in the Products search results, click on the model number that interests you. 5 Depending on the size of your screen, you may need to scroll down to see the data sheet. 6 To save or print a data sheet as a .pdf file, click Download XXX product datasheet. The characteristics presented in this manual should be the same as those that appear online. In line with our policy of constant improvement we may revise content over time to improve clarity and accuracy. In the event that you see a difference between the manual and online information, use the online information as your reference. 33003962 11/2011 9 The present documentation is intended for qualified technical personnel responsible for the implementation, operation and maintenance of the products described. It contains information necessary for the proper use of the products. However, those who wish to make a more "advanced" use of our products may find it necessary to consult our nearest distributor in order to obtain additional information. Registered Trademarks Microsoft® and Windows® are registered trademarks of Microsoft Corporation. Related Documents Title of Documentation Reference Number Vijeo-Designer Lite Online Help 33003968 Modbus Master Protocol XBT N/R/RT 33003986 Modbus SlaveProtocol XBT N/R/RT 33003980 Uni-Telway Protocol XBT N/R/RT 33003974 Siemens PPI Protocol XBT N/R/RT 33003992 AB DF1 Protocol XBT N/R/RT 33003998 AB DH485 Protocol XBT N/R/RT 33004016 Mitsubishi FX Protocol XBT N/R/RT 33004004 SYSMAC-WAY Protocol XBT N/R/RT 33004010 Zelio Protocol XBT N/R/RT EIO0000000226 Millenium Protocol XBT N/R/RT EIO0000000257 You can download these technical publications and other technical information from our website at www.schneider-electric.com. User Comments We welcome your comments about this document. You can reach us by e-mail at [email protected]. 10 33003962 11/2011 Magelis XBT N/R/RT Document Conventions 33003962 11/2011 Document Conventions 1 General information Pictograms The meaning of the pictograms used in this document is explained below. Pictogram Description Indicates information concerning the communication LED. Indicates information concerning LEDs in general. Represents a button on the Vijeo-Designer Lite program toolbar. Represents a button on the XBT terminal. 33003962 11/2011 11 Document Conventions 12 33003962 11/2011 Magelis XBT N/R/RT Overview 33003962 11/2011 Overview 2 Standards and General Safety Precautions List of Standards XBT terminals have been developed to conform to the following standards: z z z 33003962 11/2011 UL 508 for Industrial Control Equipment UL 1604 Electrical Equipment for Use in Class I and Class II Division 2 and Class III Hazardous Locations CAN/CSA-C22.2, No. 14, No. 213, and No. 60950 Industrial Control Equipment Miscellaneous Apparatus - For Hazardous Locations. 13 Overview General Safety Precautions DANGER EXPLOSION z z z z z z z Compatibility: Power and external device wiring must be in accordance with Class I, Division 2 wiring methods - Article 501- 4(b) of the National Electrical Code, Groups A, B, C and D Hazardous Locations or Non-Hazardous Locations, NFPA 70 or as specified in section 18-152 of the Canadian Electrical Code for installations within Canada and in accordance with the authority having jurisdiction. Do not perform substitution of components that may impair compliance to Class I, Division 2. Confirm that the location is not subject to any risk of explosion before connecting or disconnecting equipment, replacing or wiring modules. Confirm that the power supply has been turned OFF before disconnecting, replacing or wiring modules. Before turning ON, sweep front panel with a damp cloth to discharge electrostatics. Do not use apparatus that has been damaged. When used in hazardous locations (Class I Div.2, UL and CSA) and if suitable for the application (see product label) do not connect or disconnect equipment unless power has been switched off or the area is known to be non-hazardous. Failure to follow these instructions will result in death or serious injury. WARNING LOSS OF CONTROL Due to the risk that a value entered on the terminal may not reach the equipment (for example, if a communication break occurs due to huge bandwidth consumption, the value may not be sent to the PLC) you are not allowed to use the terminal to pilot safety critical processes, for example emergency stop or crane load manipulation where human beings may get injured. Failure to follow these instructions can result in death, serious injury, or equipment damage. 14 33003962 11/2011 Overview WARNING UNINTENDED EQUIPMENT OPERATION z z Read and follow all user instructions and documentation. Follow all local and national product safety codes and standards. Failure to follow these instructions can result in death, serious injury, or equipment damage. 33003962 11/2011 15 Overview 16 33003962 11/2011 Magelis XBT N/R/RT Characteristics of the XBT Terminal Range 33003962 11/2011 Characteristics of the XBT Terminal Range 3.1 3 Characteristics of the XBT Terminal Range Overview This section lists the characteristics of the individual versions of the XBT terminal range. What’s in this Section? This section contains the following topics: Topic 33003962 11/2011 Page Characteristics Applying to All XBT Terminals 18 Characteristics of the Individual XBT Terminals 19 Polling Times 25 17 Characteristics of the XBT Terminal Range Characteristics Applying to All XBT Terminals Overview XBT Type XBT N200 XBT N400 / XBT R400 / XBT N410 / XBT N401 / XBT RT500 / XBT NU400 / XBT R410 XBT RT511 / XBT R411 Environment Compliance with standards IEC 61131-2, IEC 60068-2-6, IEC 60068-2-27, UL 508, CSA C22-2 no. 14, no 213, and no. 60950 Product certification CE, UL, CSA, Class 1 Div 2 T5 (UL and CSA) Temperature Operation 0...+55° C (32° F...131° F) Storage -20...+60° C (-4° F...140° F) Humidity (without condensation) 0...85% Protection IP 65 - (IEC 60529 - NF C 20010) XBT RT: UL Type 4, indoor use only. Do not store or operate the LCD display in areas receiving direct sunlight since the sun’s UV rays may cause the LCD display’s quality to deteriorate. XBT N/R: UL Type 4, 4X outdoor use (only for support ≥ 1.5 mm / 0.059 in.) Front panel Rear panel ESD withstand IP 20 (IEC 60529) IEC 61000 - 4 - 2, level 3 Electromagnetic interference IEC 61000 - 4 - 3, 10 V/m Electrical interference IEC 61000 - 4 - 4, level 3 Impact IEC 60068 - 2 - 27; 1/2 sinusoidal pulse for 11 ms, 15 g on 3 axes Vibration IEC 60068 - 2 - 6 and marine certifications ± 3.5 mm 2 Hz...8.45 Hz 1 g 8.75 Hz...150 Hz XBT RT does not have marine certifications Mechanical characteristics Mounting and fixing Flush-mounted, fixed by 2 (for XBT N) or 4 (for XBT R and XBT RT) spring clips supplied pressure-mounted for panels 1.5...6 mm (0.06...0.23 in.) thick Material display unit protection Polyester Front frame Polycarbonate/polybutylene terephthalate alloy Keypad UV autotex polyester 18 33003962 11/2011 Characteristics of the XBT Terminal Range Characteristics of the Individual XBT Terminals Overview The following tables list the characteristics of the individual XBT terminal versions. XBT Type XBT N200 XBT N400 / XBT R400 / XBT N410 / XBT N401 / XBT RT500 XBT NU400 / XBT R410 / XBT R411/ XBT RT511 Electrical characteristics Power supply Voltage 5 VDC supplied by the PLC. For the specific cables see Connecting XBT Terminals (see page 57). 24 VDC (200 mA max) Voltage limits 5 V ± 5% DC, 1 W maximum 18...30 VDC, 5 W maximum Ripple factor 5% maximum NOTE: For products with a resettable fuse (XBT N410 / XBT N401 / XBT NU400 / XBT R410 / XBT R411 / XBT RT511), switch off the power supply for 5 seconds before resetting the fuse. CAUTION OVERVOLTAGE DAMAGE TO EQUIPMENT Make sure to connect the following terminals only to a source providing 5 VDC. z XBT N200 z XBT N400 z XBT R400 z XBT RT500 Failure to follow these instructions can result in injury or equipment damage. NOTE: XBT RT500 terminals are protected against accidental connection to higher voltages (up to 30 V) but the other terminal types are not and will be damaged. XBT Type XBT N200 XBT N400 / XBT N410 / XBT RT500 / XBT N401 / XBT NU400 XBT RT511 / XBT R400 / XBT R410 / XBT R411 Operating characteristics Display unit 33003962 11/2011 Type Backlit LCD Capacity 2 x 20 characters 4 x 20 characters 10 x 33 characters 19 Characteristics of the XBT Terminal Range XBT Type XBT N200 / XBT N400 / XBT N410 / XBT NU400 / XBT R400 / XBT R410 / XBT RT500 XBT N401 XBT RT511 XBT R411 Signaling No LEDs 6 LEDs 13 LEDs 14 LEDs XBT Type XBT N200 / XBT N400 / XBT N410 / XBT NU400 / XBT R400 / XBT R410 / XBT RT500 / XBT N401 / XBT R411 XBT RT511 Buzzer No buzzer Buzzer for alarm signaling and feedback on keypad/touchpad activity XBT Type XBT N200 / XBT N400 XBT N401/ XBT N410 / XBT NU400 / XBT R400 / XBT R410 / XBT R411 / XBT RT500 / XBT RT511 Dialog application No. of panels 128 200 Transmission medium (asynchronous serial link) RS232C / RS485 XBT Type XBT NU400 XBT N200 / XBT N400 / XBT R400 XBT N401 / XBT N410 / XBT R410 / XBT R411 / XBT RT500 / XBT RT511 Supported protocols Modbus master, Zelio, Millenium Modbus master, UniTelway Modbus master and slave(*), Uni-Telway, Siemens PPI, AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY, Zelio (**), Millenium (**) Real-time clock Access to the PLC real-time clock (*) Modbus slave is not supported by the XBT RT500. (**) Zelio is supported only by the XBT N401, XBT R411 and XBT RT511. (**) Millenium is supported only by the XBT N401, XBT R411 and XBT RT511. 20 33003962 11/2011 Characteristics of the XBT Terminal Range XBT Type Connection Power supply XBT N200 / XBT N400 / XBT R400 / XBT RT500 XBT N401 / XBT N410 / XBT NU400 / XBT R410 / XBT R411 / XBT RT511 Via the PLC link cable or via an external 5 V power supply by using the XBT ZRTPW accessory Removable terminal block 3 screw terminals (pitch 5.08) Clamping capacity: 1.5 mm2 (0.0023 in2) XBT Type Connection XBT N200 / XBT N400 / XBT R400 / XBT RT500 / XBT RT511 Serial link RJ45 female connector (RS232C/RS485) 25-pin female SubD connector (RS232C / RS485) XBT Type Connection Display Units Printer link XBT N401 / XBT N410 / XBT NU400 / XBT R410 / XBT R411 XBT N200 / XBT N400 / XBT N410 / XBT NU400 / XBT R400 / XBT R410 / XBT RT500 XBT N401 / XBT R411 / XBT RT511 No printer link MiniDin (full RS232C, including modem signals) Alphanumeric Display Unit XBT N200 Matrix Display Unit Matrix Display Unit Matrix Display Unit XBT N400 XBT NU400 XBT N401 Type Backlit LCD Backlit LCD 122 x 32 pixels Color Green Capacity 2 lines of 20 characters Display Green/Orange/Red 1...4 lines of 5...20 characters Active display unit 74 x 12 mm (2.91 x area (width x height) 0.47 in.) 72 x 20 mm (2.83 x 0.79 in.) Size of characters (width x height) 3.2 x 5.5 mm (0.13 x 0.22 in. 2.9 x 4.3 to 11.8 x 17.4 mm (0.11 x 0.17 to 0.46 x 0.69 in.) Keypad 8 keys, 4 of them can be re-labeled Signaling No LEDs 33003962 11/2011 6 LEDs including 4 for the 4 central keys 21 Characteristics of the XBT Terminal Range Alphanumeric Display Unit XBT N200 Matrix Display Unit Matrix Display Unit Matrix Display Unit XBT N400 XBT NU400 XBT N401 Number of panels (maximum) 128 application panels 200 application panels 256 alarm panels Variables per panel 8 40 Vertical panel scrolling no yes Number of lines per panel 2 25 Representation of variables Alphanumeric Fonts Latin + Katakana Languages Number of languages only limited by the size of the memory Display Units Functions Latin + Cyrillic + Katakana + Greek + Simplified Chinese Communication Serial link RS232 C, RS485 Protocols Modbus master, Uni-Telway Programming software Vijeo-Designer Lite (using Windows XP or Vista) Matrix Display Units XBT N410 XBT R400 Modbus master XBT R410 Modbus master and slave, Uni-Telway, Siemens PPI, AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY, Zelio, Millenium XBT R411 Display Type 22 Backlit LCD 122 x 32 pixels 33003962 11/2011 Characteristics of the XBT Terminal Range Matrix Display Units XBT N410 XBT R400 Color Green Capacity 1...4 lines of 5...20 characters XBT R410 XBT R411 Green/Orange/Red Active display unit 72 x 20 mm (2.83 x 0.79 in.) area (width x height) Size of characters (width x height) 2.9 x 4.3 to 11.8 x 17.4 mm (0.11 x 0.17 to 0.46 x 0.69 in.) Keypad 8 keys, 4 of which can 20 keys, 12 of which can be re-labeled be re-labeled Signaling No LEDs 16 LEDs including 14 for the central keys Functions Number of panels (maximum) 200 application panels 256 alarm panels Variables per panel 40 Vertical panel scrolling yes Number of lines per panel 25 Representation of variables Alphanumeric Fonts Latin + Cyrillic + Katakana + Greek + Simplified Chinese Languages Number of languages only limited by the size of the memory Communication Serial link RS232 C, RS485 Protocols Modbus master and slave, Uni-Telway, Siemens PPI, AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY Programming software Vijeo-Designer Lite (using Windows XP or Vista) 33003962 11/2011 Modbus master, UniTelway Modbus master and slave, Uni-Telway, Siemens PPI, AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY Modbus master and slave, Uni-Telway, Siemens PPI, AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY, Zelio, Millenium 23 Characteristics of the XBT Terminal Range Matrix Display Units XBT RT500 XBT RT511 Display Type Backlit LCD 198 x 80 pixels Color Green Capacity 2...10 lines of 5...33 characters Green/Orange/Red Active display unit 89.9 x 40 mm (3.54 x 1.57 in.) area (width x height) Size of characters (width x height) 2.7 x 4 to 16 x 16 mm (0.11 x 0.16 to 0.43 x 0.94 in.) Keypad 12 keys: in control and input variant 4 of them can be re-labeled, in touch variant 10 of them can be re-labeled Signaling No LEDs 13 LEDs including 10 for the central keys Functions Number of panels (maximum) 200 application panels 256 alarm panels Variables per panel 40 Vertical panel scrolling no Number of lines per panel 10 Representation of variables Alphanumeric semi-graphical (bargraph, trends, lights and buttons) Fonts Latin + Cyrillic + Katakana + Greek + Simplified Chinese Languages Number of languages only limited by the size of the memory Communication Serial link RS232 C, RS485 Protocols Modbus master , Uni-Telway, Siemens PPI, AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY Programming software Vijeo-Designer Lite (using Windows XP or Vista) 24 Modbus master and slave, Uni-Telway, Siemens PPI, AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY, Zelio, Millenium 33003962 11/2011 Characteristics of the XBT Terminal Range Polling Times Overview The polling times for non-connected equipment differ between XBT N/R/RT terminals and XBT NU400 terminals. The following sections describe general polling times of XBT N/R/RT terminals and specific polling times of XBT NU400 terminals. General Polling Time for Non-Connected Equipment The XBT N/R/RT terminal polls the missing equipment (usually a PLC) every 5 seconds. All the configured PLCs in an application should be connected. A missing equipment is therefore considered to be a temporary problem, i.e. the PLC or XBT is temporarily disconnected, and communication will resume as soon as the connection is re-established. In this arrangement, degraded communication performance is considered acceptable. 33003962 11/2011 25 Characteristics of the XBT Terminal Range Polling Time of XBT NU400 Terminals The XBT NU400 polls the missing equipment, i.e. a starter, every 5 minutes. This time interval has been selected due to performance and system validation reasons. The XBT NU400 is delivered with a unique pre-loaded application for communication with up to 8 TESYS model U starters. However, in the final system configuration, less than 8 starters may be used permanently as a normal installation. In this case, polling the missing starter(s) in too short time intervals will drastically decrease the communication with the connected starters. This, in turn, may lead to increased response times and cause critical application issues. In some cases, time between operator action and starter acknowledgement can be longer than 20 seconds. This is why the polling time of non-connected equipment has been set to this much longer period of 5 minutes. The pre-loaded application in XBTNU400 in version 2.2 and later provide a page for manually resetting the communication. During this manual restart of the terminal the reconnected devices will be detected. 26 33003962 11/2011 Magelis XBT N/R/RT Operating Elements, LEDs and Connectors 33003962 11/2011 Operating Elements, LEDs and Connectors 4.1 4 Operating Elements, LEDs and Connectors Overview This section describes all operating elements, LEDs and connectors provided on the front and rear panels of the XBT N/R/RT terminals. What’s in this Section? This section contains the following topics: Topic 33003962 11/2011 Page Front Panels 28 Rear Panels 32 Overview of Keys on the Individual XBT Terminals 34 27 Operating Elements, LEDs and Connectors Front Panels Overview The following sections list the front panels of the individual XBT terminal versions with the operating and control elements. XBT N Terminals On their front panels the XBT N terminals provide the following operating and control elements: XBT N200 XBT N401 XBT N•• 28 33003962 11/2011 Operating Elements, LEDs and Connectors 33003962 11/2011 No. Description 1 Backlit LCD display 2 Communication LED (XBT N401) 3 Alarm LED (XBT N401) 4 LEDs that can be controlled by the PLC (XBT N401) 5 Service keys for functional link 6 Service keys 7 Keys for function or numeric input (according to software configuration) 29 Operating Elements, LEDs and Connectors XBT R Terminals On their front panels the XBT R terminals provide the following operating and control elements: XBT R4•• XBT R411 30 XBT R4•• No. Description 1 Backlit LCD display 2 Communication LED (XBT R411) 3 Alarm LED (XBT R411) 4 LEDs that can be controlled by the PLC (XBT R411) 5 Service keys for functional link 33003962 11/2011 Operating Elements, LEDs and Connectors No. Description 6 Service keys 7 Control keys for function or digital input (according to the context) XBT RT Terminals On their front panels the XBT RT terminals provide the following operating and control elements: XBT RT5•• 33003962 11/2011 No. Description 1 Backlit LCD display XBT RT511 2 Service keys 3 Keys for control or service (according to software configuration) 4 Configurable touchscreen 5 Communication LED (XBT RT511) 6 Alarm LED (XBT RT511) 7 LEDs that can be controlled by the PLC (XBT RT511) 8 Touch LED (XBT RT511) 31 Operating Elements, LEDs and Connectors Rear Panels Overview The following section shows the different rear panels of the individual XBT terminal versions with their connectors. Rear Panel On their rear panels the XBT terminals provide the following connectors XBT N200 / XBT N400 / XBT R400 XBT N410 / XBT NU400 / XBT R410 XBT N401 / XBT R411 XBT RT500 XBT RT511 32 No. Description 1 RJ45: serial link + PLC power supply 2 RJ45 serial link 3 SubD25 serial link 33003962 11/2011 Operating Elements, LEDs and Connectors 33003962 11/2011 No. Description 4 3-wire terminal for 24 VDC power supply 5 MiniDIN connector for printer 33 Operating Elements, LEDs and Connectors Overview of Keys on the Individual XBT Terminals Overview The various types of XBT terminals provide different front panels including different keys for executing functions or entering values . The following paragraphs provide an overview of the keys provided on the individual XBT terminals. WARNING UNINTENDED EQUIPMENT OPERATION The control key insert label must match the configured function of the key. Failure to follow these instructions can result in death, serious injury, or equipment damage. Types of Keys The front panels of the terminals include 2 types of keys: z z Service keys Service keys provide different actions to the operator, like scrolling within the display of the terminal, selecting the panel to be displayed as well as selecting objects or entering values in the panel shown on the terminal display. Function keys Function keys are individually configured by the HMI designer who created the HMI application of the XBT terminal using the Vijeo-Designer Lite software. 2 different types of function keys are available: z static function keys: Static function keys are assigned a constant function (like selecting the panel to be displayed or executing commands) for the entire HMI application. z dynamic function keys: Dynamic function keys can be assigned different functions (like selecting the panel to be displayed, setting/resetting bits or executing commands) by the HMI designer, depending on the actually displayed panel. XBT N and XBT RT terminals can be configured for different variants (control and input variant as well as touch variant only for XBT RT) with the function keys providing different functions in each variant. XBT R terminals, on the other hand, only provide one variant. It is also possible that function keys have different functions in one variant, depending on whether you are only viewing the panels (normal mode) or you are entering values (edition mode). Function keys with 2 functions are referred to as dual labelled keys in this manual. 34 33003962 11/2011 Operating Elements, LEDs and Connectors Overview of Keys on the Terminals The individual terminals provide the following keys: XBT N XBT R XBT RT 12 customizable function 4 customizable keys which can be configured as function keys keys (control variant) or as service keys (input variant) 2 non-configurable service keys z 2 non-configurable service 2 configurable service keys for functional link keys 2 configurable service keys for functional link keys 10 customizable keys which can be configured as 10 function keys (touch variant) or as 4 function and 6 service keys (control or input variants) 2 non-configurable service keys keys z 4 non-configurable service keys configurable touchscreen Keys on XBT N Terminals XBT N terminals are customized for 2 different variants: z z control variant input variant In these 2 different variants the terminals provide the following keys on their front panels: Control variant 33003962 11/2011 Input variant 35 Operating Elements, LEDs and Connectors No. Element Description 1 Static function keys z access to a panel z impulse command z toggle command 2a Left/right arrows in control variant (functional link keys) Command link keys: z impulse command z toggle command z variable write operation Left/right arrows in input variant (functional link keys) Navigation link keys: Command link keys: z change panel in a menu z display current alarms z change digit in a variable field z impulse command z toggle command z variable write operation 3 ESC Cancel an entry or an action 4 DEL Clear the selected digit or field 5 Up/down arrows Go up, go down in a panel (XBT N40• and NU400) Increment/decrement the selected digit Select a value in a selection list Increment/decrement the value of a variable field 6 MOD Select a field Go to the next field 7 ENTER Confirm a selection or an entry Acknowledge an alarm 2b 36 Navigation link keys: z change panel in a menu z display current alarms during edition Return to the previous panel 33003962 11/2011 Operating Elements, LEDs and Connectors Keys on XBT R Terminals 33003962 11/2011 No. Element Description 1 Dual labelled keys (function/nume ric) z z z z 2 Left/right arrows (functional link keys) Navigation link keys: z change panel in a menu z display current alarms z change digit in a variable field during edition z impulse command z toggle command z variable write operation 3 ESC Cancel an entry or an action Return to the previous panel 4 DEL Clear the selected digit or field 5 Up/down arrows Go up, go down within a panel; Increment/decrement the selected digit 6 MOD Select a field Go to the next field 7 ENTER Confirm a selection or an entry Acknowledge an alarm access to a panel impulse command toggle command modification of a value Command link keys: Select a value in a selection list; Increment/decrement the value of a variable field 37 Operating Elements, LEDs and Connectors Keys on XBT RT Terminals Control variant Input variant Touch variant 38 33003962 11/2011 Operating Elements, LEDs and Connectors 33003962 11/2011 No. Element Description 1 Left/right arrows (functional link keys) Navigation link keys: z navigation: change panel in a menu z display current alarms z change digit in a variable field during edition 2 Up/down arrows Select a functional link in a panel Select a value in a selection list Increment/decrement the value of Increment/decrement the a variable field selected digit 3 ESC Cancel an entry or an action 4 DEL Clear the selected digit or field 5 MOD Select a field Go to the next field 6 ENTER Confirm a selection or an entered value Acknowledge an alarm 7a Control or touch variant Static function keys: z access a panel z impulse command z toggle command 7b Input variant Dynamic function keys (functionality is paneldependent): z access a panel z set / reset bit z impulse command z toggle command 8 Touchscreen Activity depending on the selected variant: z enabled in touch variant z disabled in control and input variant 9 Dual labelled keys The active function of keys F1 to F4 is determined by the selected terminal mode: z in edition mode: arrow keys acting like up/down/left/right arrows z in normal mode: static function keys (see description 7) Command link keys: z impulse command z toggle command z variable write operation Return to the previous panel 39 Operating Elements, LEDs and Connectors 40 33003962 11/2011 Magelis XBT N/R/RT Insert Labels 33003962 11/2011 Insert Labels 5 5.1 Insert Labels Overview This section describes the different insert labels provided for the different XBT types. What’s in this Section? This section contains the following topics: Topic Insert Labels XBT N 33003962 11/2011 Page 42 Insert Labels XBT R 44 Insert Labels XBT RT 46 41 Insert Labels Insert Labels XBT N Overview XBT N terminals are delivered with an insert label sheet providing the following label types to assign different texts or symbols to the keys: z z z service key labels function key labels blank labels All labels are pre-cut and just have to be pressed out of the label sheet. The ready-to-use service key and function key labels can directly be inserted into the XBT N terminal as described in section Inserting Insert Labels, page 49. To print your own text or symbols on the blank labels, use the Vijeo-Designer Lite configuration software. New label sheets can be ordered at Schneider with the following part numbers: XBT Terminal Label Sheet Part Number XBT N200 / XBT N400 / XBT NU400 / XBT N410 XBLYN00 XBT N401 XBLYN01 WARNING UNINTENDED EQUIPMENT OPERATION Make sure that the text/symbols on your insert label always correspond to what is configured for your XBT terminal in the Vijeo-Designer Lite configuration software. Otherwise the keys of your terminal will not initiate the actions indicated on them. Failure to follow these instructions can result in death, serious injury, or equipment damage. Service Key Labels for XBT N Terminals If you have configured your XBT N terminal for input variant in the Vijeo-Designer Lite configuration software, insert the following service key label into your XBT N terminal. Service key label XBT N Service key label XBT N401 (with LEDs) 42 33003962 11/2011 Insert Labels Function Key Labels for XBT N Terminals If you have configured your XBT N terminal for control variant in the Vijeo-Designer Lite configuration software, insert the following function key label into your XBT N terminal. Function key label XBT N Function key label XBT N401 (with LEDs) Blank Labels for XBT N Terminals The insert label sheet includes blank labels providing you the possibility to create labels with your own texts or symbols. Blank label XBT N Blank label XBT N401 (with LEDs) For a detailed description on how to print your own labels see Creating Individual Labels, page 53 33003962 11/2011 43 Insert Labels Insert Labels XBT R Overview XBT R terminals are delivered with an insert label sheet providing the following label types to assign different texts or symbols to the keys: z z function key labels blank labels All labels are pre-cut and just have to be pressed out of the label sheet. The ready-to-use function key labels can directly be inserted into the XBT R terminal as described in section Inserting Insert Labels, page 49. To print your own text or symbols on the blank labels, use the Vijeo-Designer Lite configuration software. New label sheets can be ordered at Schneider with the following part numbers: XBT Terminal Label Sheet Part Number XBT R400 / XBT R410 XBLYR00 XBT R411 XBLYR01 WARNING UNINTENDED EQUIPMENT OPERATION Make sure that the text/symbols on your insert label always correspond to what is configured for your XBT terminal in the Vijeo-Designer Lite configuration software. Otherwise the keys of your terminal will not initiate the actions indicated on them. Failure to follow these instructions can result in death, serious injury, or equipment damage. Function Key Labels for XBT R Terminals The following function key label is provided on the label sheet of XBT R terminals. Function key label XBT R Function key label XBT R411 (with LEDs) 44 33003962 11/2011 Insert Labels Blank Labels for XBT R Terminals The insert label sheet includes blank labels providing you the possibility to create labels with your own texts or symbols. Blank label XBT R Blank label XBT R411 (with LEDs) For a detailed description on how to print your own labels see Creating Individual Labels, page 53 33003962 11/2011 45 Insert Labels Insert Labels XBT RT Overview XBT RT terminals are delivered with 2 insert label sheets providing the following label types to assign different texts or symbols to the keys: z z z z service key labels function key labels touch key labels blank labels All labels are pre-cut and just have to be pressed out of the label sheet. The ready-to-use service key, function key and touch key labels can directly be inserted into the XBT RT terminal as described in section Inserting Insert Labels, page 49. To print your own text or symbols on the blank labels, use the Vijeo-Designer Lite configuration software. New label sheets can be ordered at Schneider with the following part numbers: XBT Terminal Label Sheet Part Number XBT RT500 XBLYRT00 XBT RT511 XBLYRT01 WARNING UNINTENDED EQUIPMENT OPERATION Make sure that the text/symbols on your insert label always correspond to what is configured for your XBT terminal in the Vijeo-Designer Lite configuration software. Otherwise the keys of your terminal will not initiate the actions indicated on them. Failure to follow these instructions can result in death, serious injury, or equipment damage. 46 33003962 11/2011 Insert Labels Service Key Labels for XBT RT Terminals If you have configured your XBT RT terminal for input variant in the Vijeo-Designer Lite configuration software, insert the following service key label into your XBT RT terminal. Service key label XBT RT Function Key Labels for XBT RT Terminals If you have configured your XBT RT terminal for control variant in the Vijeo-Designer Lite configuration software, insert the following function key label into your XBT RT terminal. Function key label XBT RT Touch Key Labels for XBT RT Terminals If you have configured your XBT RT terminal for touch variant in the Vijeo-Designer Lite configuration software, insert the following touch key label into your XBT RT terminal. Touch key label XBT RT 33003962 11/2011 47 Insert Labels Blank Labels for XBT RT Terminals The insert label sheet includes blank labels providing you the possibility to create labels with your own texts or symbols. Service blank label XBT RT Touch blank label XBT RT For a detailed description on how to print your own labels see Creating Individual Labels, page 53 48 33003962 11/2011 Magelis XBT N/R/RT Inserting Labels 33003962 11/2011 Inserting Labels 6 Inserting Insert Labels Overview In order to be sure that each key of the XBT terminals executes the requested function it is of vital importance that you correctly insert the insert label into the device. The following paragraphs describe the procedures of inserting insert labels into XBT N, XBT R and XBT RT terminals. WARNING UNINTENDED EQUIPMENT OPERATION Make sure that the text/symbols on your insert label always correspond to what is configured for your XBT terminal in the Vijeo-Designer Lite configuration software. Otherwise the keys of your terminal will not initiate the actions indicated on them. Failure to follow these instructions can result in death, serious injury, or equipment damage. 33003962 11/2011 49 Inserting Labels Graphical Representation of Correctly Inserting Labels into XBT N Terminals The graphic below shows how to correctly insert an insert label into an XBT N terminal: Inserting Labels into XBT N Terminals For inserting insert labels into XBT N terminals proceed as follows: Step 50 Action 1 Press the pre-cut insert label of your choice out of the insert label sheet. 2 Take your XBT N terminal and turn it around so that you can see its rear panel. On the left-hand side of the rear panel, located directly behind the overlapping display, you will find the opening for the insert label. 3 Insert the insert label cautiously into this opening (as shown in steps 1 and 2 of the above figure) until the 4 key symbols / texts have disappeared and the only sign that can still be seen of the insert label is the double arrow. 4 Turn your XBT N terminal around and check at its front side that all 4 symbols / texts are clearly visible at the keys. If the texts / symbols are not clearly visible, insert the insert label a bit further into the opening. A graphical example of a not correctly inserted insert label is provided for XBT R / RT terminals below in this chapter. 5 If the texts / symbols are clearly visible on the front of the terminal, take the part (with the double arrow sign) of the insert label that is still visible on the rear of the terminal and slide this flap into the slit indicated in step 3 of the above figure. The flap should now be flush with the rear of the terminal (see step 4 of the above figure). If the insert label has not correctly been inserted into the XBT terminal, the flap of the insert label will be too long to fit into this slit. A graphical example of a not correctly inserted insert label is provided for XBT R / RT terminals below in this chapter. 33003962 11/2011 Inserting Labels Graphical Representation of Correctly Inserting Labels into XBT R / XBT RT Terminals The graphic below shows how to correctly insert an insert label into an XBT R / XBT RT terminal: Inserting Labels into XBT R / XBT RT Terminals For inserting insert labels into XBT R / XBT RT terminals proceed as follows: Step 33003962 11/2011 Action 1 Press the pre-cut insert label of your choice out of the insert label sheet. 2 Take your XBT R / XBT RT terminal and turn it around so that you can see its rear panel. On the right-hand side of the rear panel, located directly behind the overlapping display, you will find the opening for the insert label. 3 Insert the insert label cautiously into this opening (as shown in steps 1 and 2 of the above figure) until the key symbols / texts on the wide part of the insert labels have disappeared and the wide part of the insert label is flush with the opening. There will be merely the small flap of the insert label with the double arrow being visible outside the terminal. 51 Inserting Labels Step 52 Action 4 Turn your XBT R / XBT RT terminal around and check at its front side that all symbols / texts are clearly visible at the keys. If the texts / symbols are not clearly visible, insert the insert label a bit further into the opening. Front of XBT RT terminal with insert label not correctly inserted 5 If the texts / symbols are clearly visible on the front of the terminal, take the small part (with the double arrow sign) of the insert label that is still visible on the rear of the terminal and slide this flap into the slit indicated in step 3 of the above figure. The flap should now be flush with the rear of the terminal (see step 4 of the above figure). If the insert label has not correctly been inserted into the XBT terminal, the flap of the insert label will be too long to fit into this slit. Rear of XBT terminal with insert label not correctly inserted 33003962 11/2011 Magelis XBT N/R/RT Creating Individual Labels 33003962 11/2011 Creating Individual Labels 7 Creating Individual Labels Overview For describing the procedure of creating and printing individual texts or symbols on the blank labels, blank labels of XBT R / RT terminals are used as an example in this section. The process of printing labels for XBT N terminals is identical, with the difference that they provide only 1 line of text / symbols. 33003962 11/2011 53 Creating Individual Labels Creating Individual Labels To create insert labels with your own texts or symbols, proceed as follows: Step 54 Action 1 Open the Static Function Keys dialog box in the Vijeo-Designer Lite configuration software for your XBT terminal type. 2 Click the Print Label button. Result: A special Microsoft Word template opens. Microsoft Word template for XBT RT 3 Modify the Word template to create your own key labels. 33003962 11/2011 Creating Individual Labels Step 4 33003962 11/2011 Action Print the modified Word document first on a blank paper to create a reference sheet. Printout of the modified Word template 55 Creating Individual Labels Step 56 Action 5 Position the insert label sheet on the reference printout in a way that the keys the new texts / symbols should be printed on are exactly on top of the new texts / symbols on the reference printout. Positioning insert label sheet on the reference printout 6 Fix the insert label sheet on the reference printout using adhesive tape and insert them in your printer. 7 Activate the print command to print on the insert label sheet. 8 After the texts / symbols have been printed on your insert label sheet, remove the insert label sheet from the reference printout, press the insert label out of the sheet and insert it in your terminal as described in section Inserting Insert Labels, page 49. 33003962 11/2011 Magelis XBT N/R/RT Connecting XBT Terminals 33003962 11/2011 Connecting XBT Terminals 8 Overview XBT terminals can be connected to different equipment to perform the following tasks: z z z For exchanging software configuration data with Vijeo-Designer Lite, connect the XBT terminal with a PC where Vijeo-Designer Lite is running. For controlling an automation system, connect the XBT terminal with a PLC. For printing alarms as a data stream, alarm log files or a list of current alarms, connect the XBT terminal with a printer. The following sections describe how to connect your XBT terminal to the different equipment and provides safety information concerning the cabling. What’s in this Chapter? This chapter contains the following sections: Section 33003962 11/2011 Topic Page 8.1 Grounding and Safety 58 8.2 Connecting XBT Terminals to a PC 60 8.3 Connecting XBT Terminals to a PLC 68 8.4 Connecting XBT N401 / R411 / RT511 Terminals to a Printer 80 57 Connecting XBT Terminals 8.1 Grounding and Safety Safety Information Concerning the Grounding of Terminals Danger of Point-to-Point Connections Between Separate Buildings Care must be taken when XBT terminals are directly connected to a PLC that is located in another building. When you remove the cable from the terminal, you will loose the protective earth ground of the terminal. Since these 2 buildings can have different earth grounds, unplugging the cable from the terminal can lead to an electric shock created by a ground loop (voltage potential difference between two separate buildings). DANGER HAZARD OF ELECTRIC SHOCK DUE TO IMPROPER GROUNDING z z Remove power before installing or maintaining equipment. Ensure the equipment is properly grounded to the service entrance of the building. Failure to follow these instructions will result in death or serious injury. 58 33003962 11/2011 Connecting XBT Terminals Point-to-point connections between separate buildings 1 2 3 4 5 6 7 8 33003962 11/2011 building 1 building 2 PLC XBT RT signal cable earth ground of building 1 earth ground of building 2 resistance R between the 2 earth grounds 59 Connecting XBT Terminals 8.2 Connecting XBT Terminals to a PC Overview The following sections provide information on how to connect XBT terminals to a PC for exchanging software configuration data. What’s in this Section? This section contains the following topics: Topic 60 Page Distinguishing XBT Terminals by Power Supply 61 Connecting XBT Terminals Powered by the PLC to a PC 62 Connecting XBT Terminals Powered by an External Power Supply to a PC 65 33003962 11/2011 Connecting XBT Terminals Distinguishing XBT Terminals by Power Supply Overview For exchanging software configuration data with Vijeo-Designer Lite, connect your XBT terminal to a PC running the Vijeo-Designer Lite configuration software. The correct cabling depends on whether your XBT terminal is z z powered by the PLC powered by an external 24 VDC power supply The following XBT terminals need 5 V power that must be supplied by the PC in this case: z z z z XBT N200 XBT N400 XBT R400 XBT RT500 CAUTION OVERVOLTAGE DAMAGE TO EQUIPMENT Make sure to connect the following terminals only to a source providing 5 VDC. z z z z XBT N200 XBT N400 XBT R400 XBT RT500 Failure to follow these instructions can result in injury or equipment damage. NOTE: XBT RT500 terminals are protected against accidental connection to higher voltages (up to 30 V) but the other terminal types are not and will be damaged. The following XBT terminals need an external power supply supplying 24 VDC: z z z z z z 33003962 11/2011 XBT N410 XBT N401 XBT NU400 XBT R410 XBT R411 XBT RT511 61 Connecting XBT Terminals Connecting XBT Terminals Powered by the PLC to a PC Overview The following XBT terminals need 5 V power that is usually supplied by the PLC: z z z z XBT N200 XBT N400 XBT R400 XBT RT500 When connecting these terminals to a PC for exchanging software configuration data with Vijeo-Designer Lite, the 5 V required by the terminal must be provided by the PC. CAUTION VOLTAGE DAMAGE TO EQUIPMENT Connect the serial link connector with power off and tighten connector screws. Failure to follow these instructions can result in injury or equipment damage. NOTE: For connecting XBT terminals to a PC use the Schneider cables described in the following sections. 62 33003962 11/2011 Connecting XBT Terminals Connecting XBT N200 / N400 / R400 to a PC XBT N200 / N400 and R400 terminals can be connected to a PC in 2 different ways: z z via the serial port of the PC using the Schneider cable XBT Z945 via the USB port of the PC using the Schneider cables XBT Z925 and TSXCUSB485 Connecting XBT N200 / N400 / R400 to a serial port of a PC using the Schneider cable XBT Z945 Connecting XBT N200 / N400 / R400 to a USB port of a PC using the Schneider cables XBT Z925 and TSX-CUSB485. * 33003962 11/2011 XBT N200 and XBT N400 without logo: you must add a XBT ZN999 cable adapter. 63 Connecting XBT Terminals Connecting XBT RT500 to a PC XBT RT500 terminals can be connected to a PC in 2 different ways: z z via the serial port of the PC using the Schneider cable XBT Z945 and the adaptor XBTZRT999 via the USB port of the PC using the Schneider cables XBT Z925 and TSXCUSB485 Connecting XBT RT500 to a serial port of a PC using the Schneider cable XBT Z945 and the adaptor XBT ZRT999 Connecting XBT RT500 to a USB port of a PC using the Schneider cables XBT Z925 and TSX-CUSB485 64 33003962 11/2011 Connecting XBT Terminals Connecting XBT Terminals Powered by an External Power Supply to a PC Overview The following XBT terminals need an external power supply supplying 24 VDC: z z z z z z XBT N410 XBT N401 XBT NU400 XBT R410 XBT R411 XBT RT511 When connecting these terminals to a PC for exchanging software configuration data with Vijeo-Designer Lite it is also required to connect an external power supply via the 24 VDC power supply connector that is included in the scope of delivery of these XBT terminals. CAUTION VOLTAGE DAMAGE TO EQUIPMENT Connect the serial link connector with power off and tighten connector screws. Failure to follow these instructions can result in injury or equipment damage. NOTE: For connecting these XBT terminals to a PC use the Schneider cables described in the following sections. Connecting XBT N410 / N401 / NU400 / R410 / R411 to a PC XBT N410 / N401 / NU400 / R410 / R411 terminals can be connected to a PC in 2 different ways: z z 33003962 11/2011 via the serial port of the PC using the Schneider cable XBT Z915 via the USB port of the PC using the Schneider cables XBT Z925 and TSXCUSB485 65 Connecting XBT Terminals Connecting XBT N410 / N401 / NU400 / R410 / R411 to a serial port of a PC using the Schneider cable XBT Z915 Connecting XBT N410 / N401 / NU400 / R410 / R411 to a USB port of a PC using the Schneider cables XBT Z925 and TSX-CUSB485 Connecting XBT RT511 to a PC XBT RT511 terminals can be connected to a PC in 2 different ways: z z 66 via the serial port of the PC using the Schneider cable XBT Z945 via the USB port of the PC using the Schneider cables XBT Z925 and TSXCUSB485 33003962 11/2011 Connecting XBT Terminals Connecting XBT RT511 to a serial port of a PC using the Schneider cable XBT Z945 Connecting XBT RT511 to a USB port of a PC using the Schneider cables XBT Z925 and TSX-CUSB485 33003962 11/2011 67 Connecting XBT Terminals 8.3 Connecting XBT Terminals to a PLC Overview The following sections provide information on how to connect XBT terminals to a PLC for controlling an automation system. What’s in this Section? This section contains the following topics: Topic 68 Page Distinguishing XBT Terminals by Power Supply 69 Connecting XBT Terminals Powered by the PLC to a PLC 71 Connecting XBT Terminals Powered by an External Power Supply to a PLC 75 33003962 11/2011 Connecting XBT Terminals Distinguishing XBT Terminals by Power Supply Overview For controlling an automation system, connect your XBT terminal to a PLC. The correct cabling depends on whether your XBT terminal is z z powered by the PLC powered by an external 24 VDC power supply The following XBT terminals need 5 V power that must be supplied by the PLC in this case: z z z z XBT N200 XBT N400 XBT R400 XBT RT500 CAUTION OVERVOLTAGE DAMAGE TO EQUIPMENT Make sure to connect the following terminals only to a source providing 5 VDC. z z z z XBT N200 XBT N400 XBT R400 XBT RT500 Failure to follow these instructions can result in injury or equipment damage. NOTE: XBT RT500 terminals are protected against accidental connection to higher voltages (up to 30 V) but the other terminal types are not and will be damaged. The following XBT terminals need an external power supply supplying 24 VDC: z z z z z z XBT N410 XBT N401 XBT NU400 XBT R410 XBT R411 XBT RT511 Data Exchanged Between XBT Terminals and PLCs Since data are continuously exchanged in a human/machine dialog between an XBT terminal and a PLC please consider the following recommendations. Loss of communication between the terminal and the PLC can result in partial or complete loss of control of the machine. 33003962 11/2011 69 Connecting XBT Terminals Unplugging the PLC cable during operation may lead to the loss of requests or responses exchanged between the terminal and the PLC. WARNING UNINTENDED EQUIPMENT OPERATION z z Never remove the PLC cable from the XBT terminal while operations are in progress. Check the XBT terminal connection by monitoring the communication monitoring word in the dialog table via the PLC program. Failure to follow these instructions can result in death, serious injury, or equipment damage. WARNING LOSS OF CONTROL z z z z The designer of any control scheme must consider the potential failure modes of control paths and, for certain critical functions, provide a means to achieve a safe state during and after a path failure. Examples of critical control functions are emergency stop and overtravel stop. Separate or redundant control paths must be provided for critical control functions. System control paths may include communication links. Consideration must be given to the implications of unanticipated transmission delays or failures of the link.* Each implementation of a Magelis XBT N/R/RT must be individually and thoroughly tested for proper operation before being placed into service. Failure to follow these instructions can result in death, serious injury, or equipment damage. *For additional information, refer to NEMA ICS 1.1 (latest edition), Safety Guidelines for the Application, Installation, and Maintenance of Solid State Control. 70 33003962 11/2011 Connecting XBT Terminals Connecting XBT Terminals Powered by the PLC to a PLC Overview The following XBT terminals need 5 V power that is usually supplied by the PLC but may also be supplied by an external 5 VDC power supply: z z z z XBT N200 XBT N400 XBT R400 XBT RT500 CAUTION VOLTAGE DAMAGE TO EQUIPMENT Connect the serial link connector with power off and tighten connector screws. Failure to follow these instructions can result in injury or equipment damage. Connection to Twido / Micro / Premium / Nano, Power by PLC Use the Schneider cable XBT Z9780 (RS485) to connect XBT N200 / N400 / R400 or RT500 terminals to the following Schneider PLCs that provide the required 5 VDC: z z z z Twido Micro Premium Nano Connection to Twido / Micro / Premium / Nano via Schneider cable XBT Z9780 (RS485) Connection to Modicon M340, Power by PLC Use the Schneider cable XBT Z9980 (RS485) to connect XBT N200 / N400 / R400 or RT500 terminals to a Modicon M340 PLC that provides the required 5 VDC. 33003962 11/2011 71 Connecting XBT Terminals Connection to Modicon M340 via Schneider cable XBT Z9980 (RS485) Connection to Tesys U, Altivar, Lexium 05, Zelio, Preventa XPS MC, Power by External Power Supply To connect XBT N200 / N400 / R400 or RT500 terminals to the following PLCs use the Schneider ABL8MEM05040 power supply to provide the required 5 VDC together with the adaptor XBT ZRTPW and the Schneider cable XBT Z9980 (RS485): z z z z z Tesys Model U Altivar Lexium 05 Zelio with communication module Preventa XPSMC Connection to Tesys Model U, Altivar, Lexium 05, Zelio (with communication module) or Preventa XPSMC with ABL8MEM05040 power supply with adaptor XBT ZRTPW and Schneider cable XBT Z9980 (RS485) 72 33003962 11/2011 Connecting XBT Terminals Connecting XBT RT500 to other Devices XBT RT500 terminals require different cables for connecting them to individual PLCs. Connection to PLCs using the XBT ZG939 and the XBT ZRTPW cable adapter: Cabling with PLCs: PLC Cable + XBT ZG939 cable adapter + XBT ZRTPW for power supply Advantys STB XBT Z9715 (RS232) - x Momentum XBT Z9711 (RS232C) x x Quantum / 984 XBT Z9710 (RS232C) x x Rockwell Micrologix XBT Z9733 (RS232) - x Rockwell SLC500, Drop 1761NETAIC XBT Z9734 (RS485) - x Siemens S7-200 XBT ZG9721 (RS485) - x Omron CPM1,CPM2 , CJ1 , CS1 XBT Z9743 (RS232 x x Mitsubishi FX XBT Z980 (RS232) x x 33003962 11/2011 73 Connecting XBT Terminals Communication Interruption with XBT N200 or XBT N400 Terminals A communication interruption may have occurred if ????? is displayed rather than any values, or the connection popup remains on the display unit. If you are using an XBT N200 or an XBT N400 terminal, it may be caused by the cabling because different cables are required for the different terminal versions. Use the cables as shown in the table below. If you are using other terminals or the condition still persists with these cable, refer to section Troubleshooting, page 156 or to the manual describing the protocol you are using for more information. RJ45 connector compatibility table XBT N Front Panel Cable Without Telemecanique or Schneider Electric logo XBT Z978 With Telemecanique or Schneider Electric logo XBT Z9780 74 XBT Z9780 + XBT ZN999 adaptor Application example: XBT N without Telemecanique logo connected via XBT Z9780 cable and XBT ZN999 adaptor 33003962 11/2011 Connecting XBT Terminals Connecting XBT Terminals Powered by an External Power Supply to a PLC Overview The following XBT terminals need an external power supply supplying 24 VDC: z XBT N410 z XBT N401 z XBT NU400 z XBT R410 z XBT R411 z XBT RT511 When connecting these terminals to a PLC for controlling an automation system it is also required to connect an external power supply via the 24 VDC power supply connector that is included in the scope of delivery of these XBT terminals. CAUTION VOLTAGE DAMAGE TO EQUIPMENT Connect the serial link connector with power off and tighten connector screws. Failure to follow these instructions can result in injury or equipment damage. NOTE: For connecting these XBT terminals to a PLC or a fieldbus tap use the Schneider cables described in the following sections. Connecting XBT N410 / N401 / NU400 / R410 / R411 to a PLC XBT N410 / N401 / NU400 / R410 / R411 terminals require different cables for connecting them to individual PLCs or fieldbus taps. Use the Schneider cable XBT Z938 (RS485) to connect XBT N410 / N401 / NU400 / R410 / R411 to the following Schneider PLCs: z Tesys Model U z Altivar z Lexium 05 z Zelio with communication module z Preventa XPSMC 33003962 11/2011 75 Connecting XBT Terminals Connection via the Schneider cable XBT Z938 (RS485): To connect your XBT terminal to other PLCs or fieldbus taps refer to the lists below showing the adequate cables. Connection to PLCs or fieldbus taps using different Schneider cables: Cabling with PLCs: PLC 76 Cable Advantys STB XBT Z988 (RS232) Momentum XBT Z9711 (RS232C) Quantum / 984 XBT Z9710 (RS232C) Twido/Micro/Premium/Nano XBT Z968 / Z9680 (RS485) Modicon M340 XBT Z938 (RS485) Rockwell SLC500 , Drop 1761NETAIC XBT Z9730 (RS232) Rockwell Micrologix XBT Z9731 (RS232) Mitsubishi FX XBT Z980 (RS232/RS422) Siemens S7-200 XBT Z9721 (RS485) Omron CPM1 , CPM2 , CJ1 , CS1 XBT Z9740 (RS232) 33003962 11/2011 Connecting XBT Terminals Cabling with fieldbus taps: PLC Cable LU9 GC3 XBT Z938 (RS485) SCA62 (multipoint) XBT Z908 (RS485) SCA64 XBT Z908 (RS485) TWDXCAT3RJ, TWDXCAISO XBT Z938 (RS485) Connecting XBT RT511 to a PLC XBT RT511 terminals require different cables for connecting them to individual PLCs or fieldbus taps. Use the Schneider cable XBT Z9980 (RS485) to connect XBT RT511 to the following Schneider PLCs: z Tesys Model U z Altivar z Lexium 05 z Zelio with communication module z Preventa XPSMC Connection via the Schneider cable XBT Z9980 (RS485): To connect your XBT terminal to other PLCs or fieldbus taps refer to the lists below showing the adequate cables. 33003962 11/2011 77 Connecting XBT Terminals Connection to PLCs or fieldbus taps using different Schneider cables: Cabling with PLCs: PLC Cable + XBT ZG939 cable adapter Advantys STB XBT Z9715 (RS232) - Momentum XBT Z9711 (RS232C) x Quantum / 984 XBT Z9710 (RS232C) x Twido/Micro/Premium/Nano XBT Z9780/Z9782 (RS485) - Modicon M340 XBT Z9980/Z9982 (RS485) - Rockwell Micrologix XBT Z9733 (RS232) - Rockwell SLC500 , Drop 1761NETAIC XBT Z9734 (RS485) - Siemens S7-200 XBT ZG9721 (RS485) x Omron CPM1, CPM2, CJ1 , CS1 XBT Z9743 (RS232 x Cabling with fieldbus taps: PLC Cable + XBT ZG939 cable adapter LU9 GC3 XBT Z9980 (RS485) - SCA62 (multipoint) XBT Z908 (RS485) x SCA64 XBT Z908 (RS485) x TWDXCAT3RJ, TWDXCAISO XBT Z9980 (RS485) - 78 33003962 11/2011 Connecting XBT Terminals Connecting XBT N401 / R411 / RT511 to Zelio XBT N401 / R411 / RT511 terminals require cable SR2CBL08 for connecting to Zelio. Connection via the Schneider cable SR2CBL08: Connecting XBT N401 / R411 / RT511 to Millenium 33003962 11/2011 79 Connecting XBT Terminals 8.4 Connecting XBT N401 / R411 / RT511 Terminals to a Printer Printer Connections Overview XBT N401, XBT R411 and XBT RT511 terminals provide a MiniDIN connector on their rear panel for connecting an RS232C printer. Connecting XBT N401 / R411 / RT511 to a Printer Use the Schneider cable XBT Z926 to connect your XBT N40, XBT R411 or XBT RT511 terminal to an RS232C printer. Printer connection via Schneider cable XBT Z926 80 33003962 11/2011 Magelis XBT N/R/RT Overview of Applications and Functions 33003962 11/2011 Overview of Applications and Functions 9 Overview This chapter provides an overview of applications and functions of XBT terminals. What’s in this Chapter? This chapter contains the following sections: Section 33003962 11/2011 Topic Page 9.1 Overview of Functions 82 9.2 XBT Terminals in HMI Applications 83 9.3 Functions of Keys, Touchscreen, LEDs 86 81 Overview of Applications and Functions 9.1 Overview of Functions Overview of XBT Terminal Functions Overview The flowchart below shows the different functions of XBT terminals. Representation 82 33003962 11/2011 Overview of Applications and Functions 9.2 XBT Terminals in HMI Applications HMI Applications HMI Application Example The figure below shows a typical HMI application with XBT R411. 33003962 11/2011 No. Description 1 XBT R411: terminal for visualizing data of the PLC 2 XBT R411: LED indicating the communication status 3 XBT R411 sends the alarms risen by the PLC on the flow to the printer 4 PC with Vijeo-Designer Lite for programming the XBT R411 5 XBT R411: keys for sending commands to the automation system z changing the panel z viewing current alarms z modifying digits in variable edition z activating the function associated with functional links 83 Overview of Applications and Functions No. Description 6 XBT R411: keys for modifying parameters of the PLC z acknowledging alarms z sending commands to the PLC z entering values 7 Connection to a PLC XBT N and XBT RT terminals provide different operating variants. Depending on the selected variant the keypad is either in control variant or in input variant or in touch variant (only XBT RT). In each variant, the individual keys provide different functions (for further information see Overview of Keys on the Individual XBT Terminals, page 34). To indicate the different functions to the user, the key labels are interchangeable. Blank labels are provided that can be filled with individual texts. Types of HMI Applications Applications for XBT terminals are created in the Vijeo-Designer Lite software. They can be associated with: z z z z production monitoring preventive maintenance corrective maintenance process control Production Monitoring Example In production monitoring applications XBT terminals display process status messages. XBT terminal displaying a process status message: Preventive Maintenance Example In preventive maintenance applications XBT terminals count parts for production monitoring. XBT terminal counting parts: 84 33003962 11/2011 Overview of Applications and Functions Corrective Maintenance Example In corrective maintenance applications XBT terminals indicate process conditions. XBT terminal indicating process conditions: Process Control Example In process control applications XBT terminals provide process control via configurable function keys. XBT terminal providing process control via configurable function keys: As indicated on the display unit of the XBT N in the above figure, the function pressurizing is controlled by the key named P and the function start cycle is controlled by the key named SC. 33003962 11/2011 85 Overview of Applications and Functions 9.3 Functions of Keys, Touchscreen, LEDs Overview The following sections describe the functions of keys, touchscreen and LEDs on the different XBT terminal types. What’s in this Section? This section contains the following topics: Topic 86 Page Functions of Keys and Touchscreen 87 Functions of LEDs on XBT N401 / XBT R411 / XBT RT511 Terminals 90 33003962 11/2011 Overview of Applications and Functions Functions of Keys and Touchscreen Overview All XBT terminals provide keys on their front panels that perform different functions. XBT R and XBT RT terminals provide specific keys, that can have 2 different functions depending on the current operating mode, the so-called dual labelled keys. XBT RT terminals are additionally equipped with a touchscreen that allows execution of certain functions by pushing elements directly on the display unit of the terminal. Functions of Keys The functions of the individual keys provided on XBT terminals are listed in the following table: Key Key Function Select a field for edition or move on to the next field each time MOD is pressed (left to right and top to bottom). z exit the alarm display z return to the previous panel (the last 16 panels are memorized) z exit an edition without acceptance of the value entered z z z z change panel in a menu navigate in the alarm list or in the history list select a digit in a variable field during edition Activate the function associated with a functional link: z impulse command z toggle command z writing variables z set / reset bit z go up/down within a panel (for XBT terminals providing the scrolling z z z z function) select a functional link in the panel increment/decrement the selected digit increment/decrement the value of a variable field select a value in a selection list, and modify a digit in a variable field during input z delete the selected digit or field z confirm a selection z confirm an edition z acknowledge an alarm 33003962 11/2011 87 Overview of Applications and Functions Key Key Function static function keys z access a panel z execute an impulse command z execute a toggle command z modify a value only for XBT RT: dynamic function keys having panel-dependant functions z access a panel z execute an impulse command z execute a toggle command z set / reset bit Dual Labelled Keys on XBT R and XBT RT Terminals XBT R and XBT RT terminals provide dual labelled keys. For XBT R terminals this means that keys F1 to F12 are function as well as numeric keys, i.e. they can act as function keys as well as service keys. They operate as follows: z z If the user is not modifying a value, the keys act as function keys. If the user is modifying the value of a field, the keys automatically act as service keys for edition mode. NOTE: It is impossible to enter a value if a function key has been pressed, in the same way that it is impossible to leave edition mode if the value of a field is being modified. For XBT RT terminals operated in touch variant, this means that keys F1 to F4 have different functions, depending on the selected terminal mode. z z 88 In edition mode, keys F1 to F4 act as arrow keys. In normal mode, keys F1 to F4 act as static function keys. 33003962 11/2011 Overview of Applications and Functions Touchscreen on XBT RT Terminals XBT RT terminals are equipped with a touchscreen that allows execution of functions by pushing elements directly on the display unit of the terminal. You can activate HMI objects for edition mode by directly pressing the requested object on the touchscreen. You can activate the function of a button displayed on the display unit of the terminal by directly pressing on this button. CAUTION EQUIPMENT DAMAGE z z Activate the touchscreen with fingers only. Never use sharp instruments, such as screwdrivers, as they may damage the touchscreen. Failure to follow these instructions can result in injury or equipment damage. 33003962 11/2011 89 Overview of Applications and Functions Functions of LEDs on XBT N401 / XBT R411 / XBT RT511 Terminals Overview The table below lists the functions of the LEDs provided on XBT N401, XBT R411 and XBT RT511 terminals. LED Color Status Meaning Communication Amber Off No cable or no communication Blinking Communication OK Alarms Red Alarm list: Off Touch Green Empty On Alarms already displayed Blinking New alarms not previously displayed Only available for XBT RT 511 Off When there is no activity on the touchscreen or function key On When you press the touchsceeen or function keys Input variant Up/Down Green Off Key inactive On Possibility of going up/down within a panel Blinking Indicates the possibility: z of selecting a value in a list z of incrementing/decrementing the selected digit Off On These LEDs are governed by the automation system. Their state is determined entirely by the application program of the automation system governing the terminal. As a result, their role can vary from application to application: z Signaling linked to the key (same type of role as the system LEDs above) z Signaling the status or a condition of the component governed by the key Control variant LED for static function keys 90 Green (XBT N) Amber (XBT R/R T) 33003962 11/2011 Magelis XBT N/R/RT Operating Principles of XBT Terminals 33003962 11/2011 Operating Principles of XBT Terminals 10 Overview This sections describes general principles concerning the operation of XBT terminals. What’s in this Chapter? This chapter contains the following sections: Section 33003962 11/2011 Topic Page 10.1 Modes of Operation 10.2 Panel Structure of XBT Terminals 10.3 General Configuration Settings 113 10.4 Password-Protection 119 92 99 91 Operating Principles of XBT Terminals 10.1 Modes of Operation Overview This section provides an overview of the 2 modes of operation of XBT terminals and describes their selection process. What’s in this Section? This section contains the following topics: Topic 92 Page Introduction 93 Automatic Selection of the Mode of Operation 94 Transfer Mode 95 Operating Mode 97 33003962 11/2011 Operating Principles of XBT Terminals Introduction Overview Magelis XBT terminals provide the following 2 modes of operation: z z In Transfer mode dialog applications can be exchanged between the PC running the Vijeo-Designer Lite software and the Magelis XBT terminal. In Operating mode data is exchanged between the XBT terminal and the automation system (controlling the latter). These 2 modes of operation will be described in the following sections. 33003962 11/2011 93 Operating Principles of XBT Terminals Automatic Selection of the Mode of Operation Overview On power-up, the XBT terminal automatically detects the equipment connected on its serial link and enables the suitable mode of operation (only one mode at a time). Process of Selecting the Mode of Operation Graphical presentation of the process of selecting the mode of operation 94 33003962 11/2011 Operating Principles of XBT Terminals Transfer Mode Overview In transfer mode the XBT terminal communicates with the Vijeo-Designer Lite configuration software. Software applications can be transferred in both directions. The XBT terminal automatically enables the transfer mode when it is connected to a PC via a communication cable. No operator action on the terminal is necessary in this mode. Procedure of Transferring Software Applications For transferring software applications to or from your XBT terminal perform the following steps: Step 33003962 11/2011 Action 1 Connect your XBT terminal to a PC running the Vijeo-Designer Lite software. For the suitable Schneider cable see Connecting XBT Terminals to a PC, page 60. Result: The XBT terminal automatically detects the connection to a PC, enables the transfer mode and waits for software application transfer. 2 From the Vijeo-Designer Lite software at your PC start the software application transfer. For transferring software configuration data from the PC to the XBT terminal, select the menus Device →Download.... For transferring software configuration data from the XBT terminal to the PC, select the menus Device →Upload.... XBT terminals that are equipped with a communication LED indicate data interchange with a PC by a blinking communication LED. 95 Operating Principles of XBT Terminals Transfer Mode Process Transfer mode application example 96 No. Description 1 XBT N401 2 Transfer cable (for a list of Schneider cables refer to Connecting XBT Terminals to a PC, page 60) 3 PC with Vijeo-Designer Lite 33003962 11/2011 Operating Principles of XBT Terminals Operating Mode Overview The operating mode is used for data interchange between the XBT terminal and the automation system to control the automation system. The following tasks can be performed in this mode of operation: z z z z panel display edition/modification of automation system architecture parameter values process control (discrete) viewing and acknowledging alarms The XBT terminal automatically enables the operating mode when it is connected to a PLC via a communication cable. Accessing Panels in Operating Mode When the XBT terminal is connected to a PLC, the XBT terminal automatically displays the default panel after start-up. This default panel allows navigation to the remaining panels. To navigate between panels and to access a selected panel use the arrow keys of your XBT terminal: Arrow Keys Function To navigate to another panel, press the up and down arrows of your XBT terminal. To access a selected panel, press the right arrow of your XBT terminal. Example of Accessing Panels in Operating Mode The following 2 figures illustrate how to navigate from a default panel to a panel of your choice (target panel). Default panel 33003962 11/2011 97 Operating Principles of XBT Terminals To open the Maintenance panel, press the arrow down key twice to select and then click the arrow right key to open it. Target panel 98 33003962 11/2011 Operating Principles of XBT Terminals 10.2 Panel Structure of XBT Terminals Overview XBT terminals display panels on their display unit. These panels can contain notanimated objects (e.g. background images, static texts) and not animated HMI objects (e.g. value displays, bar graphs). 3 different types of are used in XBT terminals: z z z application panels alarm panels system panels What’s in this Section? This section contains the following topics: Topic Principle of Application Panels 33003962 11/2011 Page 100 Displaying Application Panels 101 Principle of Alarm Panels 105 Alarm Management 106 Principle of System Panels 109 Displaying System Panels 110 Scrolling within Panels 111 99 Operating Principles of XBT Terminals Principle of Application Panels Definition Application panels are panels designed to provide information about the automation system architecture being run. They also serve to clarify any operation that the operator might have to carry out in a given context. Application panels can be interlinked to create authorized sequences during operation. Unauthorized operators can be prevented from displaying protected panels. 100 33003962 11/2011 Operating Principles of XBT Terminals Displaying Application Panels Default Panel on Power-Up When designing the application in Vijeo-Designer Lite, the designer can select a default panel. When the terminal is powered up, this is the first panel to be displayed. There are different ways to display application panels: z z z z z z by pressing function keys by activating navigation links provided on other application panels by pressing a button object or an active area on the touchscreen (XBT RT only) by pressing dynamic function keys Ri on products supporting this function via the PLC by activating links provided on system panels Via Function Keys It is possible to display a panel directly by pressing a function key. Example Pressing a function key for opening a specific panel: 1 function key Via Button Object or Active Area on Touchscreen By using the touchscreen of XBT RT terminals operated in touch variant you can directly access a specific panel by pressing a button object or an active area provided on the actually displayed application panel. 33003962 11/2011 101 Operating Principles of XBT Terminals Pressing a button for opening a specific panel: Via Navigation Links You can directly access a specific panel by using a navigation link provided on the actually displayed application panel. The following 2 figures illustrate how to navigate to a specific panel using a navigation link. Source panel 1 Navigation link To navigate directly to the Maintenance panel, select the arrow next to Maintenance and activate this link (by using the arrow keys of the front panel or directly touching the arrow on the touchscreen). Target panel 102 33003962 11/2011 Operating Principles of XBT Terminals Via the PLC A specific panel is displayed because the program has written the number of the panel to be processed in a word in the dialog table (for more information see Exchanging Data with the Automation System via the Dialog Table, page 151). The following figure illustrates how a specific panel is opened by the PLC. PLC opening a specific panel No. Description 1 Program, Display panel 25 2 Table read by the terminal 3 Display panel 25 4 Write acknowledgment, panel to be processed H’FFFF’ 5 Dialog table The PLC dialog table contains the number of the panel to be processed (1). The XBT terminal reads the dialog table in the PLC (2) and displays the desired panel (3). Once the command has been processed, the XBT terminal writes the value H’FFFF’ in the panel to be processed word (4), to acknowledge the request to the PLC program. From System Panels You can directly access a specific panel by using a navigation link provided on a system panel. The following figure shows a system panel providing links to application panels. 33003962 11/2011 103 Operating Principles of XBT Terminals System panel with links to application panels To navigate directly to the LIST OF ALARMS panel, select the arrow next to LIST OF ALARMS and activate this link (by using the arrow keys of the front panel or directly touching the arrow on the touchscreen). For more information about system panels, see Principle of System Panels, page 109 104 33003962 11/2011 Operating Principles of XBT Terminals Principle of Alarm Panels Objective An alarm panel has the same characteristics as an application panel with respect to: z z the text the fields The first line of an alarm panel is preconfigured (by Vijeo-Designer Lite) to show: z z z the dates and times of alarm appearance/disappearance and acknowledgment the ranking of the alarm in the alarm list the total number of alarms in the list The advantage of an alarm panel lies in its event-triggered display. Each alarm panel is associated with a word bit in the dialog table. If the bit is at state 1, the panel is displayed and the text blinks. Example Example of an alarm panel 1 Line time-stamped by the XBT terminal (A for Alarm), the alarm text appears blinking and changes to a steady display once it has been acknowledged. Listing Alarms in Operating Mode z z 33003962 11/2011 When an alarm appears, it is often the consequence of other alarms. Due to their priority system, XBT terminals can display the most important alarm, i.e. the alarm that is presenting the highest risk to the automation system architecture. All alarms are time-stamped on appearance. 105 Operating Principles of XBT Terminals Alarm Management Alarm Indication The actual display of an alarm depends on the priority it has been allocated (see section Display Priority below). Alarms pending on the automation system architecture are stored in an alarm list. The graphic below shows an Alarm LED. The Alarm LED continuously informs the operator about the state of the alarm list: z z z Off: The alarm list is empty. Blinking: The alarm list contains alarms which have appeared since the alarm list was viewed (new alarms). On: The alarm list contains alarms which occurred before the alarm list was viewed (alarms already displayed). Display Priority A priority can be associated with each alarm panel. An alarm panel has priority over an application panel and a system panel. An alarm panel does not have priority over a value, which is currently being entered. Different alarm panels may have different priorities. There are 16 possible levels of priority (the lowest display priority being priority no. 16). Exception of Priority 0 When an alarm appears on the automation system architecture that is allocated to a priority 0 alarm panel, the following will happen: z z The alarm panel is not displayed, but stored in the alarm list, thus the current display will not be disturbed. The alarm LED blinks to signal the alarm. When an alarm is activated, it is stored in the alarm list by the terminal. Appearance Types Alarm panels can appear in different ways. Alarm panels can be: z z z 106 displayed directly on the display unit printed directly from XBT terminals equipped with a printer connector (datastream printing) stored in the list of current alarms 33003962 11/2011 Operating Principles of XBT Terminals Storage Principle in the Alarm List If the alarms have equal priority, they are stored from the oldest to the most recent. If the display unit is available (i.e., not occupied by a higher-priority display), the oldest alarm is displayed. In an automation system, it is often the oldest alarm that is the most interesting, as the more recent alarms are often a consequence of the condition signaled by the first alarm (classic case of bursts of alarms). If alarms with higher priority occur the following will happen: z z Alarms with higher priority are stored at the top of the list. If the display unit is available (i.e., not occupied by a higher-priority display), the new alarm with highest priority will be displayed. Buzzer for Alarms Notification You can set alert sounds to inform you of alarms by activating the buzzer of the XBT RT511 terminal. Acknowledg-ment of Alarms When designing alarm panels, it is possible to define whether the alarm panel should be acknowledged systematically by the operator (obligatory acknowledgment) or not. To acknowledge the alarm panel on the display press ENTER. The alarm message changes to a steady display. Depending on the choice made, management of these 2 types of alarm is as follows: 33003962 11/2011 Alarms which must be acknowledged (obligatory) Alarms which can be acknowledged but do not have to be An alarm, which must be acknowledged, remains in the alarm list until it is acknowledged by the operator, even if the cause of the alarm has disappeared. An alarm, which can be acknowledged but does not have to be, disappears from the alarm list as soon as the cause of the alarm has disappeared, regardless of whether or not it has been acknowledged by the operator. Advantage: Picks up transient conditions (instability of a discrete sensor, for example). Advantage: The display unit is not monopolized by displaying alarms considered to be of minor importance to the application. 107 Operating Principles of XBT Terminals Alarm Log The terminals can manage a log of the alarm panels. They store the alarm panels with the text, but without variable values (for more information, see Alarm Log, page 143). Display Principle of Alarm Panels Representation 108 33003962 11/2011 Operating Principles of XBT Terminals Principle of System Panels Definition System panels are predefined panels which are used to perform operations relating to the XBT terminal "system". In operating mode, these panels can be accessed in the same way as application panels. System panels are panels processed as if they were application type panels. Hence they are stored with the application panels in the developed application file. There are 3 types of system panels: z z z standard system panels, which can be called by accessing an application panel (numbers 1 to 100) system panels, which cannot be called by accessing an application panel (numbers 101 to 200) popup/message system panels, which cannot be called (numbers 201 to 300) The advantage of being able to view these panels with Vijeo-Designer Lite is that system messages can be translated. 33003962 11/2011 109 Operating Principles of XBT Terminals Displaying System Panels Overview System panels are accessed by means of function keys or navigation links. When designing the application in Vijeo-Designer Lite, the designer can choose the system panels that should be associated with these keys, or these links. List of System Panels The following system panels are available to HMI operators: 110 Number Name Description 2 panel list displays a list of all application panels you can access, depending on your security access level The panels protected by password are listed only. The current security access level is in conformance with the security access level of the panel. 3 alarm list displays a list of all the active alarms triggered by the automation system 4 alarm history displays a list of the last events of the alarm history (coming alarms, going alarms, communication interruptions) 7 password On this panel you can enter the password to change the security access level (A, B, C, or blank password). 10 default system panel When a terminal cannot boot and displays a certain panel (for example, the first panel is protected by password), then the terminal displays the default system panel automatically. 22 language On this panel you can choose the language of the terminal. 30 printer displays the communication parameters for the second serial line (only significant for terminals supporting a second serial line) 100 protocol displays the parameters for the communication with the equipment connected on the automation network 110 advanced displays internal alarm counters These internal alarm counters can be of interest during calls to the technical support. 33003962 11/2011 Operating Principles of XBT Terminals Scrolling within Panels Overview Scrolling is necessary in XBT N and XBT R terminals to view the entire panel that contains more lines than the display unit can display. When opening a panel the first n (n being the number of lines on the display unit) lines of this panel are displayed on the display unit. For example, four lines for the XBT N400 terminal. Example The other lines can be displayed by scrolling up or down the panel using the up and down keys on the keypad. 33003962 11/2011 111 Operating Principles of XBT Terminals 112 33003962 11/2011 Operating Principles of XBT Terminals 10.3 General Configuration Settings Overview This section describes general settings concerning the HMI language, the date and time format as well as access to product reference and line parameters. What’s in this Section? This section contains the following topics: Topic 33003962 11/2011 Page Accessing Configuration Parameters via the System Panel SYSTEM 114 Selecting the HMI Language 115 Selecting the Date and Time Format 116 Accessing the Product Reference 117 Accessing the Line Parameters 118 113 Operating Principles of XBT Terminals Accessing Configuration Parameters via the System Panel SYSTEM Overview It is possible to configure certain terminal parameters when the terminal is in operating mode, without going into Vijeo-Designer Lite. The configuration parameters are accessed via the SYSTEM system panel (for displaying system panels, see Displaying System Panels, page 110). 114 33003962 11/2011 Operating Principles of XBT Terminals Selecting the HMI Language Overview In the HMI Language system panel choose one of the languages configured by the designer. 33003962 11/2011 115 Operating Principles of XBT Terminals Selecting the Date and Time Format In the DATE/TIME panel set the current date and time and define the date and time display format of your choice. Entering Date and Time The date and time values are entered in the same way as a variable alphanumeric field (for further information see Entering a Value in an Edition Field, page 135). Selecting Display Format The format can be configured using the Vijeo-Designer Lite program, during terminal configuration. The time format selected applies to all times and dates processed by the software, including the dates and times printed and/or displayed in the log and in the alarm list. Example The following display formats are available: Date formats Time formats DD/MM/YYYY 24:mm:ss MM/DD/YYYY 12:mm:ss YYYY/MM/DD Please note that the time you entered is only valid as long as the terminal is powered on. As soon as you power off the product the time will be lost. 116 33003962 11/2011 Operating Principles of XBT Terminals Accessing the Product Reference Overview The references of the XBT terminals can be accessed from the system panels. The references of the XBT terminal can be obtained if the designer has provided access to these panels (link to the system panels). The following information is displayed: z z z z z z z product reference name of the application developed in Vijeo-Designer Lite date and time when the application file was saved in Vijeo-Designer Lite communication protocol name version of Vijeo-Designer Lite used to create the application XBT terminal BIOS reference and version XBT terminal application software reference and version NOTE: The most important information is placed on the first few lines so that it is displayed consecutively, avoiding the need to scroll through the panel. 33003962 11/2011 117 Operating Principles of XBT Terminals Accessing the Line Parameters Overview System panels contain detected error counters whose content is protocoldependent. For further information refer to the XBT protocol manual describing the protocol you are using. 118 33003962 11/2011 Operating Principles of XBT Terminals 10.4 Password-Protection Accessing Password-Protected Panels, Fields, Functional Links Protection To be sure that only authorized persons are able to read and write data, it is possible to protect: z z z access to panels modification of fields control via functional links If an operator does not have authorization: z z protected panels no longer appear in the list of panels protected fields behave as if they had been configured as read-only Password To access password-protected areas enter your password via the Password system panel. A navigation link to the Password system panel is required on one of the application panels. (For more information about how system panels are displayed, see Displaying System Panels, page 110). XBT terminals provide three access levels: A, B and C. The passwords for these levels are defined in Vijeo-Designer Lite. A password consists of four alphanumeric characters (default value: 1111). 33003962 11/2011 119 Operating Principles of XBT Terminals 120 33003962 11/2011 Magelis XBT N/R/RT Communication with the Automation System 33003962 11/2011 Communication Between XBT Terminals and the Automation System 11 Overview This chapter provides information about the communication between XBT terminals and the automation system, listing the types of commands and how they are activated as well as the processes of entering / modifying values or handling alarms. What’s in this Chapter? This chapter contains the following sections: Section 33003962 11/2011 Topic Page 11.1 Types of Commands 11.2 Activating Commands 125 11.3 Entering / Modifying Values Alphanumeric Fields in Edition Mode 132 11.4 Handling Alarms 140 11.5 Printing Alarms 144 122 121 Communication with the Automation System 11.1 Types of Commands Overview This section describes the 2 types of commands that can be sent via function keys (or functional links) or button object on touchscreen of the XBT terminal to the automation system: z z impulse commands toggle commands What’s in this Section? This section contains the following topics: Topic 122 Page Impulse Commands 123 Toggle Commands 124 33003962 11/2011 Communication with the Automation System Impulse Commands Impulse Command The automation system is activated by pressing a function key (or functional link) or button object on touchscreen of XBT RT terminals. If the key (or functional link) is released, the action stops. Example Motor command 33003962 11/2011 Key Bit released 0 pressed 1 released 0 123 Communication with the Automation System Toggle Commands Toggle Command The automation system is activated by pressing the function key (or functional link) or button object on the touchscreen of XBT RT terminals. If the function key (or functional link) is pressed again, the action on the control system stops. Example Conveyor forward command 124 Key Bit released 0 pressed 1 released 1 pressed 0 33003962 11/2011 Communication with the Automation System 11.2 Activating Commands Overview This section describes the different ways commands can be activated at XBT terminals. What’s in this Section? This section contains the following topics: Topic 33003962 11/2011 Page Activating Commands via Functional Links, Button Objects or Dynamic Function Keys on the Display Unit 126 Activating Commands via Function Keys on the Display Unit 131 125 Communication with the Automation System Activating Commands via Functional Links, Button Objects or Dynamic Function Keys on the Display Unit Overview Functional links, button objects and dynamic functions are integrated by the application designer on the different panels to create additional control functions. To activate functional links, use the left and right keys on the front panel of the XBT terminals. To activate buttons, press the button directly on the screen if your XBT terminal is equipped with a touchscreen. If your XBT terminal is not equipped with a touchscreen, press the MOD key to select the button and the ENTER key to activate the button. Example of a button object To activate dynamic functions, use the Ri keys on the front panel of the XBT terminals. These keys can also be linked to pictograms on screen. Example of dynamic function keys linked to pictograms on screen Links, button objects and dynamic functions are programmed by the application designer to send different types of commands to the equipment from the application panel: z z z 126 impulse commands toggle commands set value 33003962 11/2011 Communication with the Automation System z z reset value write value Functional Link Example No. 33003962 11/2011 Description 1 Change panel (link blinking to indicate that it is active) 2 Change panel 3 Toggle (link blinking to indicate that it is active) 127 Communication with the Automation System Representation of Command Links Example No. Description 1 Toggle 2 Impulse (link blinking to signal that the link is active) Buttons Example of XBT RT in touch variant 128 33003962 11/2011 Communication with the Automation System No. Description 1 Push button on touchscreen to go to the Conveyorpanel. 2 Push button on touchscreen to activate the function. Example of XBT RT in No-touch variant 33003962 11/2011 No. Description 1 Press the MOD key once to select the button. 2 Press the ENTER key to go to the Conveyor panel. 3 Press MOD and ENTER to activate the function. 129 Communication with the Automation System Dynamic Function Keys Example of dynamic function keys linked to pictograms 130 No. Description 1 Pictograms illustrating the functions of the dynamic function keys. 2 Dynamic function keys. 33003962 11/2011 Communication with the Automation System Activating Commands via Function Keys on the Display Unit Example Function key 1 Function key The dialog table enables dialog between the PLC and the terminal. In this table, one word is reserved to supply the PLC with the status of the function keys in the form of a word bit. Bit 15 to Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reserved F12 F11 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 33003962 11/2011 131 Communication with the Automation System 11.3 Entering / Modifying Values Alphanumeric Fields in Edition Mode Overview This section describes how to select and modify alphanumeric fields, i.e. fields that allow to enter characters (A-Z) and numbers (0-9). What’s in this Section? This section contains the following topics: Topic 132 Page Accessing an Alphanumeric Edition Field 133 Entering a Value in an Edition Field 135 Confirming / Cancelling an Edition 137 Exit Edition on Time Out 138 Edition Report 139 33003962 11/2011 Communication with the Automation System Accessing an Alphanumeric Edition Field Overview Alphanumeric edition fields can either be accessed by the user or by the automation system. User Selecting an Edition Field To access an alphanumeric edition field, it must first of all be visible on the display unit. To select the field, press the MOD key of the XBT terminal. If there are several edition fields available on the actually displayed panel, press the MOD key several times in succession to run through the variable fields in edition mode from left to right and from top to bottom. You access an alphanumeric edition field on XBT RT terminals in touch variant directly by touching the screen if an active area has been configured by the HMI application designer. Example Selecting an edition field out of several edition fields on the same panel: 1st time MOD is pressed: If no edition has been made in any field on the display unit since the panel was displayed, the top left-hand field on the display unit is the edition field (field no. 1) Otherwise the edition field will be the one that has already been edited (field no. 1, 2, 3 or 4). We will assume that field no. 1 is the edition field 33003962 11/2011 2nd time MOD is pressed: Edition field no. 2 3rd time MOD is pressed: Edition field no. 3 4th time MOD is pressed: Edition field no. 4 133 Communication with the Automation System 5th time MOD is pressed: Edition field no. 1, etc. Field no. 5 cannot be the edition field because it is not visible on the display unit. Automation System Accessing an Edition Field The connected device sets a variable field into edition mode by writing its number in a word in the dialog table. To display the number of variable fields in Vijeo-Designer Lite, use the Layout →Display Fields Indices menu. In return, the XBT terminal writes the number of the field being completed in a word in the dialog table (see Exchanging Data with the Automation System via the Dialog Table, page 151). Specific feature of this type of selection: You cannot select another variable field at the XBT terminal until the one requested by the connected device has been completed because the MOD key is inactive during this time. 134 33003962 11/2011 Communication with the Automation System Entering a Value in an Edition Field Input Methods Before you can enter a value in an edition field, activate the input mode in the XBT terminal. After you have activated the input mode for a field, the whole field blinks and the following edition methods are available: z z z z accelerated incremental edition thumbwheel edition direct edition direct edition via virtual numeric keypad Edition Methods Key Description Accelerated Incremental Edition: Down/Up The total value of the field is increased or decreased by pressing the up/down keys. Thumbwheel Edition: Left/Right z First, the digit to be modified is selected and starts blinking when the up and Down/Up down keys are pressed. (These keys are managed in the same way as a drum. This means that on reaching one end of the variable field, you go back to the other end.) z Next, when the left and right keys are pressed, the digit values are displayed in one direction or the other (these keys are also managed in the same way as a drum). 33003962 11/2011 135 Communication with the Automation System Edition Methods Key Description Direct Edition (XBT R4•• only): Key F1 to F12 Keys F1 to F12 are dual labelled Fx/Nx (function/numeric) keys. They can be used to modify values directly. The correspondence between keys and numeric values is as follows: Key Value F1 1 F2 2 F3 3 F4 4 F5 5 F6 6 F7 7 F8 8 F9 9 F10 0 F11 +/- F12 . Virtual numeric keypad on Direct Input via touchscreen of XBT RT: Virtual numeric Keypad (XBT RT in touch variant only): 136 Activate the individual buttons on the touchscreen with your finger to enter the respective character. 33003962 11/2011 Communication with the Automation System Confirming / Cancelling an Edition Overview To confirm or to cancel the edition of alphanumeric fields, use the ENTER and ESC key. Confirming an Edition ENTER key If you press the ENTER key after you have modified an edition field, the entered value is transmitted to the connected device. Refreshment of the field, which was in edition mode, is active again. Canceling an Edition ESC key If you press the ESC key after you have modified an edition field, the following will happen: z z z 33003962 11/2011 No write action is performed to the automation system. The value prior to edition is redisplayed. Refreshment of the field, which was in edition mode, is active again. 137 Communication with the Automation System Exit Edition on Time Out Overview If you have enabled edition mode but you do not press any key for more than 1 minute, edition mode will be disabled automatically and the following will happen: z z 138 No write action is performed to the automation system. Refreshment of the field, which was in edition mode, is active again. 33003962 11/2011 Communication with the Automation System Edition Report Overview After the edition mode has been disabled, the connected equipment is informed of how the edition ended: z z z confirmation cancellation time out by updating the Report word in the dialog table. 33003962 11/2011 139 Communication with the Automation System 11.4 Handling Alarms Overview This section describes how to view, ignore and print alarms. Please note that these functions are not available for XBT N200 terminals. What’s in this Section? This section contains the following topics: Topic 140 Page Viewing or Ignoring Alarms 141 Alarm Log 143 33003962 11/2011 Communication with the Automation System Viewing or Ignoring Alarms Overview When an alarm occurs, it is automatically displayed on the display unit. An alarm is displayed blinking You can now view and acknowledge the alarm or you can ignore the alarm. Viewing Alarms To view the alarm, use the keys of your XBT terminal as described below: Key Description Scroll through the alarm panel (up to 25 lines). Scroll through the list of alarm panels. Press the ENTER key to acknowledge the alarm on the display. The alarm message stops blinking and changes to a steady display. Press the ESC key to exit viewing alarm panels. 33003962 11/2011 141 Communication with the Automation System Example Using the left and right arrow keys to scroll through the alarm list: Ignoring Alarms To ignore an actual alarm, use the ESC as described below Key Description If an alarm is displayed during operation, you can press the ESC key to return to operating mode. The alarm remains in the list and the ALARM LED changes to a steady display. 142 33003962 11/2011 Communication with the Automation System Alarm Log Log Principles Alarms are automatically stored in a log file one after another. Once the log file is full, new alarms overwrite the oldest alarms. In this way each alarm event (for appearance, acknowledgment, disappearance see Listing Alarms in Operating Mode (see page 105)) is recorded and time-stamped. NOTE: XBT R411 and XBT RT511 are the only terminals that save a log. The retention period for the log is limited to twelve hours. After that time the log may be cleared. Any other XBT terminal types loose the information stored in the log as soon as they are switched off. NOTE: To store an alarm panel in the log, the store option must be enabled for the panel. You can view, clear and print the log which will be described in the following sections. Viewing the Log You can access the alarm log from the MENU system panel (see Displaying System Panels (see page 110)). MENU system panel Once inside the log, you can browse through the various alarms (see Viewing Alarms (see page 141)). Clearing the Log To clear the log file proceed as follows: Step 33003962 11/2011 Action 1 In the MENU system panel select ALARMS LOG. 2 In the following panel select CLEAR. Result: The alarm log is empty. 143 Communication with the Automation System 11.5 Printing Alarms Overview This section provides a general overview of the printing function for alarms. Please note that this function is only available for XBT N401, XBT R411 and XBT RT511 terminals. What’s in this Section? This section contains the following topics: Topic 144 Page Principles of Printing Alarms 145 Printing Alarms as a Data Stream 146 Printing the Alarm Log 147 33003962 11/2011 Communication with the Automation System Principles of Printing Alarms Overview You can print alarms in the following different ways that will be described in the following sections: z z z 33003962 11/2011 printing alarms as a data stream printing the alarm log printing the list of current alarms 145 Communication with the Automation System Printing Alarms as a Data Stream Overview The alarm name and status are printed whenever an alarm status changes. The following information are printed: z z z z z alarm number name of the alarm panel print date print time alarm status NOTE: In order for an alarm panel to be printed, the print option must be enabled for the panel . Example Alarm 1 appeared, was acknowledged and then disappeared. Alarm 2 is present but has not been acknowledged. 146 33003962 11/2011 Communication with the Automation System Printing the Alarm Log Initiated by the Operator The log is printed in sequential order (sorted by status), with the most recent alarm at the top. The following information is printed for each alarm: z z z z z its number name of the alarm panel date and time of appearance date and time of acknowledgment date and time of disappearance Initiated by the PLC The log is printed by means of the print command word in the dialog table. The log is printed in sequential order (sorted by status), with the most recent alarm at the top. The following information is printed for each alarm: z z z z z alarm number name of the alarm panel date and time of appearance date and time of acknowledgment date and time of disappearance Example Alarm 1 appeared, was acknowledged and then disappeared. Alarm 2 is present but has not been acknowledged. 33003962 11/2011 147 Communication with the Automation System 148 33003962 11/2011 Magelis XBT N/R/RT Vijeo-Designer Lite Configuration Software 33003962 11/2011 Vijeo-Designer Lite Configuration Software 12 Overview This chapter provides a short reference to the Vijeo-Designer Lite configuration software for XBT terminals. What’s in this Chapter? This chapter contains the following topics: Topic 33003962 11/2011 Page Creating XBT Terminal Applications 150 Exchanging Data with the Automation System via the Dialog Table 151 149 Vijeo-Designer Lite Configuration Software Creating XBT Terminal Applications Criteria An XBT terminal application consists of the entire dialog between the operator and the automated process. In its entirety, this should take account of: The criteria relating to the automation system: The user criteria: The criteria for creating the actual dialog application: z z z z z user interface z level of intervention z programming z debugging z upgrading production monitoring preventive maintenance corrective maintenance process control NOTE: These constraints mean that it is necessary to structure your application. An application should consist of a set of panels that can be arranged in a tree structure. Example of a Panel Tree Structure Tree structure 150 33003962 11/2011 Vijeo-Designer Lite Configuration Software Exchanging Data with the Automation System via the Dialog Table Overview Dialog tables are integrated in the PLCs that are connected to XBT terminals. A dialog table is a set of data exchanged between the PLC and the XBT terminal. Dialog tables are used to inform terminals of alarm states. For more information on the data exchange between XBT terminals and connected equipment via dialog tables refer to the Vijeo-Designer Lite online help. 33003962 11/2011 151 Vijeo-Designer Lite Configuration Software 152 33003962 11/2011 Magelis XBT N/R/RT 33003962 11/2011 Appendices Overview This part provides additional information on this manual. What’s in this Appendix? The appendix contains the following chapters: Chapter 33003962 11/2011 Chapter Name Page A Troubleshooting and Further Information 155 B Architectures of Automation Systems 163 153 154 33003962 11/2011 Magelis XBT N/R/RT Troubleshooting and Further Information 33003962 11/2011 Troubleshooting and Further Information A Overview This chapter provides additional information about troubleshooting, alert messages, internal variables and self-tests of the terminals. What’s in this Chapter? This chapter contains the following topics: Topic 33003962 11/2011 Page Troubleshooting 156 System Messages 158 Internal Variables 160 Terminal Self-Tests 162 155 Troubleshooting and Further Information Troubleshooting Overview Condition Cause Remedy ????? displayed rather than any values The transmission parameters set in the Vijeo-Designer Lite software for the protocol you are using for communication are not configured correctly. Check the transmission parameters in the dialog box of the Vijeo-Designer Lite software for the protocol you are using. For more detailed information refer to the user manual of this protocol. No memory allocation for this variable has Allocate memory space for the variable been declared in the PLC Cannot read dialog table message displayed on terminal The equipment declared for the variable does not exist Modify the list of equipment and check the declared addresses The equipment is not connected to the terminal Check the connection The equipment is connected to the terminal via an XBT Z978 cable Check the connection. Try using an XBT Z9780 cable The equipment is connected to the terminal via an XBT Z9780 cable Check the connection. Try using an XBT Z978 cable (equivalent to an XBT Z9780 cable equipped with an XBT ZN999 adaptor). The equipment declared for the dialog table does not exist Modify the list of equipment and check the declared addresses No memory allocation for the dialog table Allocate memory space for the dialog has been declared in the PLC table in the PLC (e.g., %MW100 to %MW125) The equipment is not connected to the terminal Check the connection Incorrect dialog table authorization message The value of the authorization word stored in the PLC is not correct Using Vijeo-Designer Lite, check the expected value (\Configuration\Dialog Table) for the Authorization Table and its location in the memory equipment Product seems to be not powered (backlight not on and nothing displayed on the display unit XBT N401/NU400: No 24 V power supply Check the power supply 156 XBT N200/400: z No power supply via the PC mouse port. z Dialog table forces the back-light to remain off. z No power supply via the PLC communication port in run mode. Check whether the PC mouse port has been activated (see PC Control Panel), check the PLC program. Check whether the cable is connected to the PLC port. Check that power is being supplied to the PLC. 33003962 11/2011 Troubleshooting and Further Information Condition Cause Remedy Cannot read/write variable message The equipment declared for the variable does not exist Check the addresses declared for the equipment The variable does not have a valid address in the declared device Check the variable address The equipment is not connected to the terminal Check the connection Import impossible XBT--> PC Application protected by password Ask the creator of the application for the password Inoperative keys Locked by the dialog table Check the PLC program Incorrect terminal configuration Check that the terminal configuration is correct for input or control or touch variant No application message No application Transfer an application No printing No connection Connect the cable and check that it is connected correctly at both ends. Then check that the printer is switched on. The cable connecting the printer to the terminal is incorrect Check that the cable is the appropriate type Incorrect printer configuration Refer to the printer manual to check that the configuration saved by the terminal is the same as the current configuration Every other line is printed The terminal is configured as LF rather than auto-LF Abnormal printing Lines are printing one on top of the other. The terminal is configured as auto-LF rather than LF 33003962 11/2011 157 Troubleshooting and Further Information System Messages Single-Language System Messages System messages generated by the XBT (single-language system messages: English), non-configurable. System Message Description APPLICATION FAULT: Application inconsistency. AUTOTEST IN PROGRESS: Autotests running. BIOS ERROR # x CS:x IP:x: Critical BIOS issue, consult Schneider Electric. CHECKSUM FAILED: Firmware checking result. DOWNLOAD ABORTED: Download to the XBT canceled by the operator. Redo a download. DOWNLOAD COMPLETED: Download to the XBT finished. DOWNLOAD FAILED: Download to the XBT not completed. DOWNLOAD IN PROGRESS: Download to the XBT in progress. FPU ERROR # function x: Critical math libraries result, consult Schneider Electric. INCORRECT TERMINAL TYPE IN .DOP FILE: Application is exported to a terminal type X when it had been created for a terminal type Y. KERNEL TRAP #x ES:x IP:x: Critical real-time kernel result, consult Schneider Electric. NO APPLICATION: Product has no application. PROCESSOR TRAP # x CS:x IP:x: Critical terminal result, consult Schneider Electric. RUNTIME ERROR # x CS:x IP:x: Critical RUNTIME result, consult Schneider Electric. SWITCH POWER OFF CS:x IP:x: Critical terminal result, consult Schneider Electric. UPLOAD ABORTED: Upload to the PC canceled by the operator. UPLOAD COMPLETED: Upload to the PC finished. UPLOAD FAILED: Upload to the PC not completed. UPLOAD IN PROGRESS: Upload to the PC in progress. WAITING FOR TRANSFER: Awaiting remote loading. WIRING FAULT: Wiring problem. Multi- Languages System Messages XBT system messages (6 languages), which can be translated by Vijeo-Designer Lite in the system panels. 158 33003962 11/2011 Troubleshooting and Further Information Number System Message Description #244 ALARM LIST EMPTY: No alarms logged in the terminal. #203 CANNOT READ DIALOG TABLE: Connection problems between XBT <-> PLC. #241 CANNOT READ VARIABLE: Variable cannot be read. #202 CANNOT WRITE DIALOG TABLE: Writing to a protected zone or XBT <-> PLC connection problems. #242 CANNOT WRITE VARIABLE: Variable cannot be written. #204 CONNECTION IN PROGRESS: XBT is trying to connect to the PLC. #247 DATE FORMAT INVALID: The date cannot be displayed because of its format. #201 DIALOG TABLE AUTHORIZATION: Authorization word is incorrect. #251 LANGUAGE DOES NOT EXIST: Language not entered in the XBT. #250 LANGUAGE IMPOSED BY THE PLC: Current language determined by the PLC. #257 LOG CLEARING IN PROGRESS: Following an operator request, the log is being cleared. #243 OVERFLOW MIN <= VALUE <= MAX: Input of a value, which is outside the limits. #249 PAGE DOES NOT EXIST: Call-up of a non-existent page. #253 PASSWORD IMPOSED BY THE PLC: Current password determined by the PLC. #258 PRINTING STOPPED BY USER: The operator sent a request to stop the current print job. The next job in the print buffer will be printed as soon as the end of the line in the first print job is reached. #255 PRINT RECOGNISED: The print request sent by the operator has been accepted and placed in the processing buffer: it will be processed as soon as the current print job is completed. #254 PROTECTED ACCESS PAGE: Call-up of a page protected by password. #256 REFUSED: PRINTING IS ALREADY IN PROGRESS: The same print request was sent twice in succession by the operator before the first print request could be fulfilled. The request is rejected. #246 TIME FORMAT INVALID: The time cannot be displayed because of its format. #248 WRONG PASSWORD: Input of an incorrect password. 33003962 11/2011 159 Troubleshooting and Further Information Internal Variables Purpose XBT terminals provides internal variables you can use to display information on your panels or to control your terminal. List of the Internal Variables 160 Variable Type Description %MW0... %MW299 All Buffer (This variable is only available in Modbus Slave applications.) %MW50000 Word Date in ASCII %MW50001 Word Time in ASCII %MW50002 Word Seconds (0 to 59) %MW50003 Word Minutes (0 to 59) %MW50004 Word Hour %MW50010 to %MW50056 Word Free words %MW50057 Word Quick increment from 0 to 65535 %MW50058 Word Quick decrement from 65535 to 0 %MW50059 Word Increment from 0 to 9 every 2 seconds %MW50060 Word Decrement from 9 to 0 every 2 seconds %MW10000 Word Transmission speed %MW10001 Word Parity %MW10005 Word Address number %MW10006,0 Bit Counters reset %MW10007... %MW10015 Word Counters 1...9 (value depending on the protocol) %MW10026 Word Mute all buzzer output %MW10028 Word Value of the programmed language %MW10033 String Password level in progress %MW10034 String Password input in progress %MW10035 Word Reset current password value (=0 for Reset). %MW10036 String Product reference %MW10037 String Application name %MW10038 String Date of the last application backup %MW10039 String Time of the last application backup 33003962 11/2011 Troubleshooting and Further Information Variable 33003962 11/2011 Type Description %MW10040 String Protocol name %MW10041 String Build time version %MW10042 String Firmware version %MW10043 String Run time name %MW10044 String Run time version %MW10050... %MW10059 Word Counter 10...19 (value depending on the protocol) %MW11000 Word Value of the panel to be displayed %MW12000 Word Values >0 clear the history %MW12001 Word Values >0 print the history %MW12020 Word Values >0 print the alarm list %MW12030 Word Values >0 stop the printing process %MW60023 Word Acknowlegment of all alarms 161 Troubleshooting and Further Information Terminal Self-Tests Overview XBT terminals perform 2 types of self-tests: z z self-test during power-up continuous self-test during operation Self-Test Power-Up When the terminal is powered up, the following self-tests are performed: Element Tested Test Principle Non-passing Result Criterion Action in Event of Non-Passing The working memory Writing/reading (RAM) Value read different from value Operation impossible: STOP written The firmware Checksum calculation and checking Calculated checksum <> stored checksum Operation impossible: STOP The application memory Checksum calculation and checking Calculated checksum <> stored checksum Operation impossible: Transfer compulsory Continuous Self-Test A continuous self-test checks that the program is operating correctly (watchdog). NOTE: If a problem is detected that prevents operation of the product, the terminal turns off all its LEDs, stops working and displays a system message number (if the detected condition permits it to do so). If the same problem still persists after the terminal has been switched back on, inform the maintenance department of this system message number. 162 33003962 11/2011 Magelis XBT N/R/RT Architectures of Automation Systems 33003962 11/2011 Architectures of Automation Systems B Types of Architectures of Automation Systems Communication via Protocols Communication between the XBT terminal and connected equipment is achieved by means of a communication protocol, which is selected when creating the application in Vijeo-Designer Lite. The protocols available for the XBT range support communication with the Schneider range of PLCs, specific equipment (speed drives) and third party PLCs. Supported protocols are Uni-Telway, Modbus (master and slave), Siemens PPI, AB DF1, AB DH485, Mitsubishi FX, SYSMAC-WAY. Please note that not all XBT types support all protocols. The following types of architecture are possible, which enable 1 XBT terminal to be linked to several equipment or several XBT terminals to 1 equipment: z point-to-point connections z multipoint connections z multidrop connections For more information on the protocols, please refer to the Protocols User Manuals. Point-to-Point Connection (all XBT terminals) 1 XBT terminal linked to 1 equipment. 33003962 11/2011 163 Architectures of Automation Systems Protocols: z Modbus master z Uni-Telway slave z Siemens PPI (*) z AB DF1 (*) z AB DH485 (*) z Mitsubishi FX (*) z SYSMAC-WAY (*) z Zelio (**) z Millenium (**) (*) XBT N200/N400/R400 do not support these protocols. (**) Zelio is supported only by the XBT N401, XBT R411 and XBT RT511. (**) Millenium is supported only by the XBT N401, XBT R411 and XBT RT511. Multipoint Connection (XBT N401 / N410 / NU400 / R410 / R411 / RT511) 1 XBT terminal linked to several equipment (maximum of 15). Protocols: z Modbus master z Uni-Telway slave z Siemens PPI z AB DF1 z AB DH485 z Mitsubishi FX z SYSMAC-WAY 164 33003962 11/2011 Architectures of Automation Systems Multidrop Connection (XBT N401 / N410 / R410 / R411 / RT511) Several XBT terminals linked to 1 equipment. Protocols: z Modbus slave z Uni-Telway 33003962 11/2011 165 Architectures of Automation Systems 166 33003962 11/2011 Magelis XBT N/R/RT Glossary 33003962 11/2011 Glossary A alarm panel Information panel displayed when an alarm occurs on the automation system. An alarm panel is displayed by the automation system, when the associated boolean variable changes. It is generally used to provide to the operator all the information and the description of the actions he has to do, in order to deal with the current alarm. alarm table An alarm table is a communication table that contains only words related to alarm functions. Each bit of alarm words can be associated to an alarm. The equipment can use it to signal to the terminal that an alarm has occurred. The terminal can use the status words of the alarm table to report to the equipment that the operator has acknowledged an alarm. alphanumeric characters (A-Z) and numbers (0-9) alphanumeric display units These are only capable of displaying characters (with a font resolution usually 5x7 pixels). The characters are physically separated from one another. 33003962 11/2011 167 Glossary alphanumeric terminals These are equipped with alphanumeric display units or matrix display units used in character mode only. animated HMI object Object which representation and behavior depends on operator actions or on variables belonging to an equipment or to the terminal. application Please refer to HMI application. application browser Structure tree representing the HMI application. The application bar is located at the left of the Vijeo Designer Lite user interface. application panel An application panel can be displayed either by the operator or by the equipment of the automation system. It can display any information about the automation system. It allows the operator to input data into the automation system and to navigate from one panel to others. automation system all components (e.g. PLCs, HMI terminals, sensors, actuators) of an automated process B bitmap Image with fixed dimensions, which can be handled by a Windows software. button Windows object used to perform the action described by the label or the symbol it contains A button is validated on touch screen or by pressing the enter key while the button is selected. 168 33003962 11/2011 Glossary C command table Part of the dialog table completed by the control system. This word list contains all the instructions passed to the terminal. communication table generic word for either a dialog table or an alarm table configuration software Vijeo Designer Lite is the configuration software that allows to create a HMI application and transfer it between a terminal and an equipment. current language The language of the HMI application the designer is working on. D default terminal language The HMI language used by the terminal when it is powered on. demo version Version of Vijeo-Designer Lite used to demonstrate the configuration software.This version does not allow any transfer of the HMI application between the VijeoDesigner Lite software and an XBT terminal. designer Please refer to HMI designer. dialog application Set of data, necessary and sufficient to describe the behavior of a terminal during operation. Vijeo Designer Lite is the only tool that can be used to create this type of application for Schneider Electric terminals. 33003962 11/2011 169 Glossary dialog table A dialog table is a communication table that can contain words related to any function of the terminal. A dialog table can include an alarm table. The purpose of a dialog table is to exchange data or orders between the terminal and the connected equipment. download Transfer of an HMI application from an XBT terminal to Vijeo-Designer Lite. dynamic function keys These keys are placed on the front face of a terminal and their behavior depends on the displayed panel.You can set different function to them (e.g. panel access, command functions, object selection). E equipment Any device (generally a PLC) which communicates with a terminal. external variable Variable which belongs to an equipment. F firmware This is the terminal on-board software. It comprises mainly the BIOS and the loader used to communicate with Vijeo-Designer Lite. H HMI human machine interface 170 33003962 11/2011 Glossary HMI application Names all the data necessary to describe the behavior of an HMI terminal in the operating mode. Vijeo Designer Lite is the configuration software that allows to create an HMI application. HMI designer (or designer) The person who designs an HMI application using Vijeo Designer Lite. Even if there is no particular training to use Vijeo-Designer Lite, some skills in process automation are recommended to create a application. HMI language An HMI application can be designed in several different languages. Each of these languages is an HMI language. HMI object (or object) The smallest element contained in a panel. Can be either an animated or an notanimated HMI object. HMI operator (or operator) The person who uses an HMI terminal in operation mode, in order to control and lead an automated installation or machine. An operator is a person who does not have any specific skill in process automation or computer science. HMI terminal (or terminal) Electronic terminal used by operators to control an automation system. An HMI terminal is mainly used to display information and alarms from the automation system, to allow the operator to input some parameter values into the automation system, and to control it. Basically, a terminal replaces former control panels that were mainly made of push buttons, lamps, indicators and measurement devices. I internal variable Variable which belongs to the terminal. 33003962 11/2011 171 Glossary Some internal variables provide services (like date/time) that can be used by the HMI designer without any restriction, as if they were PLC/equipment variables. L link HMI object contained in a panel used to access application panels or system panels (navigation links) or to perform command functions (command links). loader Part of terminal firmware responsible for handling communication with Vijeo Designer Lite to transfer a application in one direction or the other. Its role is also to store application data, sent by Vijeo Designer Lite, in the terminal memory. M Magelis Generic commercial name of the all range of Schneider HMI terminals. matrix display units These consist of a continuous matrix of pixels, enabling the display of characters in different fonts and sizes, and also basic graphics. The technology and resolution of these display units is, however, too low for them to be considered true graphic display units. matrix touch screen (or touch screen) Transparent sheet stuck on a display, composed of a matrix of areas and sensible to operator action on it. menu Title, located in a menu bar, allowing by selection to access a list of menu items. Each of these menu items is associated with a function. mode of operation There are 2 modes of operation: z operating mode z transfer mode 172 33003962 11/2011 Glossary N not-animated HMI object Object which representation is constant. It is always displayed exactly as it has been configured. O object Please refer to HMI object. operating mode A terminal´s mode of operation in which the terminal communicates with one or several equipment of an automation system. This is the normal operating mode of a terminal, when it uses the HMI application. The operator generally uses the terminal in this operating mode. Please refer to transfer mode. operator Please refer to HMI operator. optimum version Version of a terminal that can only be connected to some of the Schneider PLCs. Main characteristics: z just enough features z external 5 VDC power supply (mainly provided by the PLC) z 1back-light color P panel A terminal can display a panel. Its size can be larger than the terminal display. In this case, the terminal allows using the scrolling to move the visible part of the panel. A panel can contain not-animated objects (e.g. background images, static texts) and animated objects (e.g. value displays, bar graphs). 33003962 11/2011 173 Glossary There are 3 different types of panels: z application panel z alarm panel z system panel panel editor The panel editor displays the panel in WYSIWYG format (what you see is what you get). If the panel can not be displayed completely in the editor, a scroll bar is displayed. pilot device A terminal can communicate with several control system-devices. Of these, only one is able to send commands to the terminal, and is capable of knowing its status; this device is called the pilot device. It contains the dialog table. PLC programmable logic controller protocol language of the communication between a terminal and equipment(s) connected to an industrial network R reference language Language in which the designer constructs his application panels. By default, it is the installation language of the Vijeo-Designer Lite programming software. S service keys Keys on the keypad necessary for certain terminal functions (scrolling, selecting fields, data input, requesting a menu, etc.). standard version Version of a terminal with standard functionality. 174 33003962 11/2011 Glossary Main characteristics: z external 24 VDC power supply z point to point and multi-point connection z 1 back-light color static function keys Keys placed on the front face of a terminal. Their behavior is the same for the whole application. You can set different functions to them (e.g. panel access, command functions). status bar Zone located at the bottom of a Windows window. It is used to indicate the state of the application or active element to the developer. status table Part of the dialog table completed by the terminal. This word list represents the terminal status. system panel A system panel is a pre-built, ready to use panel, which is systematically embedded into an HMI application. A system panel can be displayed either by the operator or by the equipment of the automation system, or by the terminal itself. It informs the operator about system or automation errors by a system popup panel. It allows the operator to change some terminal parameters (e.g. date, HMI language) and to navigate from one panel to others. T terminal Please refer to HMI terminal. third party Indicates the fact that it is not a Schneider product. As an example it can be used for: z third party protocol z third party PLC 33003962 11/2011 175 Glossary thumbwheel edition Rudimentary edition mode based on the same principle as mechanical thumbwheels: selection of the digit to be modified by means of the horizontal arrow key(s), then selection of the digit value by means of the vertical arrow key(s). touch screen Please refer to matrix touch screen. transfer mode A terminal´s specific mode of operation in which the terminal is able to communicate with the configuration software to transfer an HMI application. The HMI designer mainly uses the terminal in this mode of operation. Please refer to operating mode. tree structure Structure representing the application panels and the links between them. By extension, this window is used to represent the structure of all types of panels. U universal version Version of a terminal that can be connected to Schneider and third party PLCs in point to point as well as multi-point. Main characteristics: external 24 VDC power supply z point to point and multi-point connection z light indicators z 3 back-light colors z peripheral connection (printer) z upload Transfer of an HMI application from Vijeo-Designer Lite software to an XBT terminal. user Either an operator or a designer (when it is not necessary to make the distinction). 176 33003962 11/2011 Glossary V variable Storage element containing a value evolving during the time. Can be either a internal variable or an external variable. variable field Area on a panel configured to display an item depending on the value of a variable in the connected equipment. version There are 3 terminal versions: z please refer to optimum version z please refer to standard version z please refer to universal version Vijeo-Designer Lite Configuration software for the low end Magelis range. It replaces the XBT-L1000 software. W WYSIWYG What You See Is What You Get. X XBT Any HMI terminal (when it is not necessary to make the distinction). 33003962 11/2011 177 Glossary 178 33003962 11/2011 Magelis XBT N/R/RT Index 33003962 11/2011 B AC Index Specials A alarm buzzer, 107 alarm list, 106, 107, 107 alarm log, 108, 143 clearing, 143 display, 143 principles, 143 alarm management, 106 alarm panels, 141 acknowledgment, 107 advantages in operating mode, 105 appearance types, 106 display, 108 display priority, 106 displaying, 141 ignoring alarms, 142 log, 108, 143 objective, 105 principle, 105 principles, 105 storage principle, 107 viewing, 141, 141 alarms objective, 105 appearance types, 106 application, 150 33003962 11/2011 application panels definition, 100 display, 101 principle, 100 applications, 83 automation system architectures mulitipoint connection, 164 multidrop connection, 165 point-to-point connection, 163 B blank labels, 53 button object, 126 C cable, 93 cabling, 62 cancelling an edition, 137 characteristics, 18, 19 commands impulse, 123 toggle, 124 confirming an edition, 137 connection multidrop, 165 multipoint, 164 to a PC, 62 connectors, 32 control elements, 28 controlling automation system, 97 179 Index D date and time, 116 display format, 116 input, 116 dialog table exchanging data via, 151 display of a panel, 101 display of an application panel on power up, 101 dual labelled keys, 87 dynamic function keys, 126 E edition cancellation, 137 confirmed, 137 report, 139 environmental influences, 18 exchanging data via the dialog table, 151 F function keys dynamic, 34 static, 34 functional command link representation, 128 functional link, 126 functions of keys, 87 of touchscreen, 87 XBT terminals, 82 H HMI language selection, 115 human/machine dialog, 83 I impulse commands, 123 180 input exit on time out, 138 of a value, 135 input/modification of a value, 133 insert label XBT N, 42 insert label XBT R, 44 insert label XBT RT, 46 K key functions, 87 keys, 28, 34 L label insert label XBT N, 42 insert label XBT R, 44 insert label XBT RT, 46 language, 115 LED communication, 93 LED functions, 90 LEDs, 28 line parameters, 118 error counters, 118 log file, 143 M managing alarms, 106 material, 18 MiniDIN, 32 mode of operation selection, 94 modes of operation operating mode, 93, 109 transfer mode, 93, 96 mounting, 18 O operating elements, 28 operating mode, 93, 97 33003962 11/2011 Index operation mode selection, 94 P panels, 28 password-protection, 119 PC connection to PC, 62 PLC architectures, 163 polling times, 25 printing, 145 alarm log, 147 as a data stream, 146 principles, 145 printing blank labels, 53 process commands via function keys, 131 via functional links, 126 product reference, 117 protecting the terminal, 119 protocols, 163 terminal self-test, 162 continuous, 162 on power-up, 162 time out input mode, 138 toggle commands, 124 touchscreen functions, 87 transfer mode, 96 transferring software applications, 95 W word report, 139 X XBT NU400 polling times, 25 R RJ45, 32 S scrolling within panels, 111 selecting an edition field, 133 by the operator, 133 by the pilot equipment, 134 selecting mode of operation, 94 setting the display parameters, 114 standards, 18 structure of XBT applications, 83 SubD25, 32 system panels, 109, 110 definition, 109 principle, 109 T temperature, 18 33003962 11/2011 181 Index 182 33003962 11/2011 ">
/
Download
Apenas um lembrete amigável. Você pode visualizar o documento aqui mesmo. Mas o mais importante, nossa IA já o leu. Ele pode explicar coisas complexas em termos simples, responder às suas perguntas em qualquer idioma e ajudá-lo a navegar rapidamente, mesmo nos documentos mais longos ou complicados.
Link público atualizado
O link público para seu chat foi atualizado. Você pode visualizar e gerenciar seus links de chat após o registro aqui.
Link público do documento
Anúncio
