Asus P8H67 Specifications

Motherboard
P8H67-V
E6142
First Edition (V1)
November 2010
Copyright © 2010 ASUSTeK Computer Inc. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK Computer Inc. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product may contain copyrighted software that is licensed under the General Public License (“GPL”)
and under the Lesser General Public License Version (“LGPL”). The GPL and LGPL licensed code in this
product is distributed without any warranty. Copies of these licenses are included in this product.
You may obtain the complete corresponding source code (as defined in the GPL) for the GPL Software,
and/or the complete corresponding source code of the LGPL Software (with the complete machinereadable “work that uses the Library”) for a period of three years after our last shipment of the product
including the GPL Software and/or LGPL Software, which will be no earlier than December 1, 2011, either
(1) for free by downloading it from http://support.asus.com/download;
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source code
we would be much obliged if you give us a notification to the email address [email protected], stating the
product and describing the problem (please do NOT send large attachments such as source code archives
etc to this email address).
ii
Contents
Notices.......................................................................................................... vi
Safety information...................................................................................... vii
About this guide......................................................................................... vii
P8H67-V specifications summary.............................................................. ix
Chapter 1:
Product introduction
1.1
Welcome!....................................................................................... 1-1
1.2
Package contents.......................................................................... 1-1
1.3
Special features............................................................................. 1-1
1.3.1
Product highlights............................................................ 1-1
1.3.2
Innovative ASUS features................................................ 1-3
1.4
Before you proceed...................................................................... 1-5
1.5
Motherboard overview.................................................................. 1-6
1.6
1.7
1.8
1.9
1.5.1
Placement direction......................................................... 1-6
1.5.2
Screw holes..................................................................... 1-6
1.5.3
Motherboard layout.......................................................... 1-7
1.5.4
Layout contents................................................................ 1-7
Central Processing Unit (CPU).................................................... 1-8
1.6.1
Installing the CPU............................................................ 1-8
1.6.2
Installing the CPU heatsink and fan................................1-11
1.6.3
Uninstalling the CPU heatsink and fan.......................... 1-12
System memory.......................................................................... 1-13
1.7.1
Overview........................................................................ 1-13
1.7.2
Memory configurations................................................... 1-14
1.7.3
Installing a DIMM........................................................... 1-18
1.7.4
Removing a DIMM......................................................... 1-18
Expansion slots........................................................................... 1-19
1.8.1
Installing an expansion card.......................................... 1-19
1.8.2
Configuring an expansion card...................................... 1-19
1.8.3
PCI slots......................................................................... 1-19
1.8.4
PCI Express x1 slots...................................................... 1-19
1.8.5
PCI Express x16 slots.................................................... 1-19
Jumpers....................................................................................... 1-21
iii
Contents
1.10
Connectors.................................................................................. 1-22
1.10.1
Rear panel connectors................................................... 1-22
1.10.2
Internal connectors........................................................ 1-24
1.11
Onboard switches....................................................................... 1-31
1.12
Onboard LEDs............................................................................. 1-33
1.13
Software support......................................................................... 1-34
1.13.1
Installing an operating system....................................... 1-34
1.13.2
Support DVD information............................................... 1-34
Chapter 2:
2.1
2.1.1
ASUS Update utility......................................................... 2-1
2.1.2
ASUS EZ Flash 2............................................................. 2-2
2.1.3
ASUS CrashFree BIOS 3 utility....................................... 2-3
2.1.4
ASUS BIOS Updater........................................................ 2-4
2.2
BIOS setup program..................................................................... 2-7
2.3
Main menu................................................................................... 2-11
2.4
2.5
iv
BIOS information
Managing and updating your BIOS............................................. 2-1
2.3.1
System Language ..........................................................2-11
2.3.2
System Date ..................................................................2-11
2.3.3
System Time...................................................................2-11
2.3.4
Security...........................................................................2-11
Ai Tweaker menu......................................................................... 2-13
2.4.1
Ai Overclock Tuner ....................................................... 2-13
2.4.2
Memory Frequency ....................................................... 2-14
2.4.3
EPU Power Saving MODE ........................................... 2-14
2.4.4
GPU Boost..................................................................... 2-14
2.4.5
DRAM Timing Control.................................................... 2-14
2.4.6
CPU Power Management.............................................. 2-14
2.4.7
CPU Offset Mode Sign . ................................................ 2-15
2.4.8
DRAM Voltage .............................................................. 2-16
2.4.9
VCCIO Voltage ............................................................. 2-16
2.4.10
CPU PLL Voltage .......................................................... 2-16
2.4.11
PCH Voltage ................................................................. 2-16
2.4.12
Load-Line Calibration . .................................................. 2-16
2.4.13
CPU Spread Spectrum ................................................. 2-16
Advanced menu.......................................................................... 2-17
Contents
2.6
2.5.1
CPU Configuration......................................................... 2-17
2.5.2
System Agent Configuration.......................................... 2-19
2.5.3
PCH Configuration......................................................... 2-19
2.5.4
SATA Configuration........................................................ 2-20
2.5.5
USB Configuration......................................................... 2-21
2.5.6
Onboard Devices Configuration..................................... 2-21
2.5.7
APM............................................................................... 2-23
Monitor menu.............................................................................. 2-24
2.6.1
CPU Temperature / MB Temperature............................. 2-24
2.6.2CPU / Chassis / Power Fan Speed................................ 2-24
2.7
2.8
2.9
2.6.3
CPU Q-Fan Control ...................................................... 2-25
2.6.4
Chassis Q-Fan Control ................................................. 2-25
2.6.5
CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage... 2-26
2.6.6
Anti Surge Support ....................................................... 2-26
Boot menu................................................................................... 2-27
2.7.1
Bootup NumLock State ................................................. 2-27
2.7.2
Full Screen Logo . ......................................................... 2-27
2.7.3
Option ROM Messages ................................................ 2-28
2.7.4
Setup Mode .................................................................. 2-28
2.7.5
Boot Option Priorities..................................................... 2-28
2.7.6
Boot Override................................................................. 2-28
Tools menu.................................................................................. 2-29
2.8.1
ASUS EZ Flash 2........................................................... 2-29
2.8.2
ASUS O.C. Profile.......................................................... 2-29
Exit menu..................................................................................... 2-30
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference, and
•
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
vi
Safety information
Electrical safety
•
To prevent electric shock hazard, disconnect the power cable from the electric outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
•
Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
•
Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.
Operation safety
•
Before installing the motherboard and adding devices on it, carefully read all the manuals
that came with the package.
•
Before using the product, ensure that all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
•
Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
About this guide
This user guide contains the information you need when installing and configuring the
motherboard.
How this guide is organized
This guide contains the following parts:
• Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it
supports.
•
Chapter 2: BIOS information
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
vii
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task.
CAUTION: Information to prevent damage to the components when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1.
ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2.
Optional documentation
Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.
Typography
Bold text
Italics
<Key>
<Key1>+<Key2>+<Key3>
viii
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<D>
P8H67-V specifications summary
CPU
Chipset
Memory
Graphics
Multi-GPU support
Expansion slots
GA1155 socket for Intel® Second Generation Core™ i7 /
Core™ i5 / Core™ i3 Processors
Supports 32nm CPU
Supports Intel® Turbo Boost Technology 2.0
* The Intel® Turbo Boost Technology 2.0 support depends on the
CPU types.
** Refer to www.asus.com for Intel® CPU support list.
Intel® H67 Express Chipset
Dual-channel memory architecture
- 4 x 240-pin DIMM sockets support unbuffered non-ECC
DDR3 1333/1066MHz memory modules
- Supports up to 32GB system memory
- Support Intel® Extreme Memory Profile (XMP)
* The Max. 32GB memory capacity can be supported with
DIMMs of 8GB (or above). ASUS will update QVL once the
DIMMs are available on market.
** Refer to www.asus.com or this user manual for the
Memory QVL (Qualified Vendors Lists).
*** When you install a total memory of 4GB capacity
or more, Windows® 32-bit operating system may only
recognize less than 3GB. We recommend a maximum
of 3GB system memory if you are using a Windows®
32-bit operating system.
Multi-VGA output support: HDMI, DVI-D, RGB
- Supports RGB with max. resolution up to 2048 x 1536 @75HZ
- Supports DVI with max. resolution up to 1920 x 1200 @60HZ
- Supports HDMI with max. resolution up to 1920 x 1200 @60HZ
- Maximum shared memory of 1748 MB
Supports ATI® Quad-GPU CrossFireX™ Technology
1 x PCI Express 2.0 x16 slot (blue, single at x16 mode)
1 x PCI Express 2.0 x16 slot (black, at x4 mode, compatible with
PCI Express x1 and x4 devices)
2 x PCI Express 2.0 x1 slots
3 x PCI slots
*The PCIe x1 slots share the bandwidth with the PCIe x16_2
slot.
**Due to the CrossFireX™ limitation, DO NOT use the
PCIe x1 slots when you install two CrossFireX™ graphics
cards on both the PCIe x16 slots to set up a CrossFireX™
configuration.
***To disable the PCIe X1 slot, refer to the Onboard Devices
Configuration section in the BIOS for details.
(continued on the next page)
ix
P8H67-V specifications summary
Storage
LAN
Audio
USB
ASUS special feature
ASUS unique
features
Rear panel ports
Intel® H67 Express Chipset:
- 4 x Serial ATA 3Gb/s connectors (blue)
- 2 x Serial ATA 6Gb/s connectors (gray)
- Intel® Rapid Storage technology supports RAID 0, 1, 5, 10
VIA® VT6415:
- 1 Ultra DMA 133/100 for up to 2 PATA devices
PCIE Gigabit LAN controller
ALC887 8-channel High Definition Audio CODEC
Intel® H67 Express Chipset:
- 12 x USB 2.0/1.1 ports (8 ports at mid-board, 4 ports at the
back panel)
ASMedia® 1042 USB 3.0 controller:
- 2 x USB 3.0 ports (blue) at the back panel
100% All High-quality Conductive Polymer Capacitors
ASUS Turbo V
Anti-Surge protection
GPU Boost
MemOK!
ASUS EPU
ASUS Fan Xpert
AI Suite II
Auto Tuning
ASUS CrashFree BIOS 3
ASUS EZ Flash 2
ASUS MyLogo 2
1 x PS/2 Keyboard/Mouse COMBO port
1 x Optical S/PDIF out port
1 x HDMI port
1 x DVI port
1 x VGA port
1 x LAN (RJ-45) port
2 x USB 3.0/2.0 ports (blue)
4 x USB 2.0/1.1 ports
8-channel audio ports
continued on the next page
Internal connectors
BIOS features
Manageability
Accessories
Support DVD
Form factor
4 x USB 2.0/1.1 connectors support additional 8 USB 2.0/1.1 ports
1 x IDE connector
1 x System panel connector
1 x S/PDIF Out connector
2 x SATA 6.0Gb/s connectors (gray)
4 x SATA 3.0Gb/s connectors (blue)
1 x Front panel audio connector
1 x CPU fan connector
2 x Chassis fan connectors
1 x Power fan connector
1 x COM connector
1 x MemOK! switch
1 x GPU Boost switch
1 x 24-pin EATX Power connector
1 x 8-pin EATX 12V Power connector
32 Mb Flash ROM, EFI BIOS, PnP, DMI v2.0, WfM2.0,
SMBIOS v2.6, ACPI v2 0a, Multi-language BIOS
WOL by PME, WOR by PME, PXE
1 x UltraDMA 133/100 cable
2 x Serial ATA 6.0 Gb/s cables
1 x I/O shield
User Manual
Drivers
ASUS Update
ASUS Utilities
Anti-virus software (OEM version)
ATX form factor: 12 in x 9 in (30.5 cm x 22.9 cm)
* Specifications are subject to change without notice.
xi
xii
Chapter 1
Product introduction
1.1
Welcome!
Thank you for buying an ASUS® P8H67-V motherboard!
The motherboard delivers a host of new features and latest technologies, making it another
standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the items in
your package with the list below.
1.2
Package contents
Check your motherboard package for the following items.
Motherboard
ASUS P8H67-V motherboard
Cables
2 x Serial ATA 6.0Gb/s cables
1 x Ultra DMA 133/100 cable
Accessories
1 x I/O shield
Application DVD
ASUS motherboard support DVD
Documentation
User Manual
If any of the above items is damaged or missing, contact your retailer.
1.3
Special features
1.3.1
Product highlights
LGA1155 socket for Intel® Second Generation Core™ i7/
Core™ i5/ Core™ i3 Processors
This motherboard supports the Intel® Second Generation Core™ i7/
Core™ i5/ Core™ i3 processors in LGA1155 package with memory and
PCI Express controllers integrated to support 2-channel (4 DIMMs) DDR3
memory and 16 PCI Express 2.0 lanes. This provides great graphics
performance. Intel® Second Generation Core™ i7/ Core™ i5/ Core™ i3
processors are among the most powerful and energy efficient CPUs in
the world.
ASUS P8H67-V
1-1
Intel® H67 Express Chipset
The Intel® H67 Express Chipset is the latest single-chipset design to
support the new 1155 socket Intel® Core™ i7 / Core™ i5 / Core™ i3 2nd
generation processors. It provides improved performance by utilizing
serial point-to-point links, allowing increased bandwidth and stability.
Additionally, the H67 provides 2 SATA 6.0 Gb/s and 4 SATA 3.0 Gb/s
ports for faster data retrieval at double the bandwidth of current bus
systems.
Dual-Channel DDR3 1333 / 1066MHz support
The motherboard supports DDR3 memory that features data transfer
rates of 1333 / 1066 MHz to meet the higher bandwidth requirements
of the latest 3D graphics, multimedia, and Internet applications. The
dual-channel DDR3 architecture enlarges the bandwidth of your system
memory to boost system performance.
True Serial ATA 6Gb/s support
The Intel® H67 Express Chipset natively supports the Serial ATA (SATA)
interface, delivering up to 6.0 Gb/s data transfer.
USB 3.0 support
Experience ultra-fast data transfer at 4.8Gbps with USB 3.0 – the latest
connectivity standard. Built to connect easily with next-generation
components and peripherals, USB 3.0 transfers data 10x faster and is
also backward compatible with USB 2.0 components.
PCI Express 2.0 support
This motherboard supports PCI Express 2.0 devices for double speed
and bandwidth which enhances system performance.
S/PDIF out connector at the back I/O
This motherboard provides convenient connectivity to external home
theater audio systems via the optical S/PDIF (SONY-PHILIPS Digital
Interface) out connecor at the back I/O. The S/PDIF transfers digital audio
without converting it to analog format and keeps the best signal quality.
8-channel high definition audio
The onboard 8-channel HD audio (High Definition Audio, previously
codenamed Azalia) CODEC enables high-quality 192KHz/24-bit audio
output and jack-detect feature that automatically detects and identifies
what types of peripherals are plugged into the audio I/O jacks and notifies
users of inappropriate connection, which means there will be no more
confusion of Line-in, Line-out, and Mic jacks.
1-2
Chapter 1: Product introduction
Gigabit LAN solution
The onboard LAN controller is a highly integrated Gb LAN controller. It is
enhanced with an ACPI management function to provide efficient power
management for advanced operating systems.
100% All High-quality Conductive Polymer Capacitors
This motherboard uses all high-quality conductive polymer capacitors for
durability, improved lifespan, and enhanced thermal capacity.
Quad-GPU CrossFireX™ Support
The motherboard’s powerful Intel® H67 platform optimizes PCIe allocation
in multiple-GPU configurations of CrossFireX™. This allows you to enjoy
a never before-experienced brand new gaming style.
1.3.2
Innovative ASUS features
ASUS EFI BIOS (EZ Mode)
ASUS brand new EFI BIOS offers a user-friendly interface that goes
beyond traditional keyboard BIOS input to enable more flexible and
convenient mouse controls. You can easily navigate the new EFI BIOS
with the same smoothness as their operating system, while the exclusive
EZ Mode displays frequently-accessed setup info, while the Advanced
Mode is for experienced performance enthusiasts that demand far more
intricate system settings.
MemOK!
MemOK! quickly ensures memory boot compatibility. This remarkable
memory rescue tool requires a mere push of the button to patch memory
issues. MemOK! determines failsafe settings and dramatically improves
your system boot success. Get your system up and running in no time.
ASUS TurboV
Feel the adrenaline rush of real-time OC-now a reality with the ASUS
TurboV. This easy OC tool allows you to overclock without exiting or
rebooting the OS; and its user-friendly interface makes overclock with just
a few clicks away. Moreover, the ASUS OC profiles in TurboV provides
the best O.C. settings in different scenarios.
Auto Tuning
Auto Tuning is an intelligent tool that automates overclocking to achieve
a total system level up. This tool also provides stability testing. Even O.C.
beginners can achieve extreme yet stable overclocking results with Auto
Tuning!
ASUS P8H67-V
1-3
GPU Boost
GPU Boost overclocks the integrated GPU in real time for the best
graphics performance. User-friendly UI facilitates flexible frequency and
voltage adjustments. Its ability to deliver multiple overclocking profiles
also provides rapid and stable system-level upgrades.
Fan Xpert
ASUS Fan Xpert intelligently allows you to adjust the CPU and chassis
fan speeds according to different ambient temperatures caused by
different climate conditions in different geographic regions and your PC’s
loading. The built-in variety of useful profiles offer flexible controls of fan
speed to achieve a quiet and cool environment.
AI Suite II
With its fast user-friendly interface, ASUS AI Suite II consolidates all the
exclusive ASUS features into one simple to use software package. It
allows you to supervise overclocking, energy management, fan speed
control, voltage and sensor readings. This all-in-one software offers
diverse and ease to use functions, with no need to switch back and forth
between different utilities.
ASUS Anti-Surge Protection
This special design prevents expensive devices and the motherboard
from damage caused by power surges from switching power supply
(PSU).
ASUS EPU
ASUS EPU is a unique power saving technology that detects the current
system loadings and adjusts the power consumption in real time.
ASUS MyLogo2™
This feature allows you to convert your favorite photo into a 256-color
boot logo for a more colorful and vivid image on your screen.
ASUS CrashFree BIOS 3
ASUS CrashFree BIOS 3 is an auto-recovery tool that allows you to
restore a corrupted BIOS file using the bundled support DVD or USB
flash disk that contains the latest BIOS file.
ASUS EZ Flash 2
ASUS EZ Flash 2 is a utility that allows you to update the BIOS without
using an OS-based utility.
1-4
Chapter 1: Product introduction
C.P.R. (CPU Parameter Recall)
The BIOS C.P.R. feature automatically restores the CPU default settings
when the system hangs due to overclocking failure. C.P.R. eliminates the
need to open the system chassis and clear the RTC data. Simply shut
down and reboot the system, and the BIOS automatically restores the
CPU parameters to their default settings.
ErP ready
The motherboard is European Union´s Energy-related Products (ErP)
ready, and ErP requires products to meet certain energy efficiency
requirements in regards to energy consumptions. This is in line with
ASUS vision of creating environment-friendly and energy-efficient
products through product design and innovation to reduce carbon
footprint of the product and thus mitigate environmental impacts.
1.4
Before you proceed
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
• Unplug the power cord from the wall socket before touching any component.
• Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due to
static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.
• Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so may
cause severe damage to the motherboard, peripherals, or components.
ASUS P8H67-V
1-5
1.5
Motherboard overview
Before you install the motherboard, study the configuration of your chassis to ensure that the
motherboard fits into it.
Ensure that you unplug the power cord before installing or removing the motherboard.
Failure to do so can cause you physical injury and damage motherboard components.
1.5.1
Placement direction
1.5.2
Screw holes
When installing the motherboard, ensure that you place it into the chassis in the correct
orientation. The edge with external ports goes to the rear part of the chassis as indicated in
the image below.
Place six screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
P8H67-V
1-6
Chapter 1: Product introduction
1.5.3
Motherboard layout
1
2
1
3
1
4
5
22.9cm(9.0in)
KB_USB34
GPU Boost
CPU_FAN
SPDIFO
_HDMI
6
DRAM_LED
8
2
CHA_FAN1 PWR_FAN
PRI_IDE
AAFP
PCIEX1_1
VT6415
Lithium Cell
CMOS Power
EATXPWR
P8H67-V
AUDIO
7
MemOK!
30.5cm(12.0in)
LAN1_USB12
DDR3 DIMM_B2 (64bit, 240-pin module)
USB3_12
DDR3 DIMM_B1 (64bit, 240-pin module)
LGA1155
DDR3 DIMM_A2 (64bit, 240-pin module)
DVI_VGA
DDR3 DIMM_A1 (64bit, 240-pin module)
EATX12V
1
CHA_FAN2
ASM1042
32Mb
BIOS
PCIEX16_1
PCIEX1_2
AR
8151
Intel®
H67
PCI1
Super
I/O
PCIEX16_2
ASM
1083
PCI2
SATA3G_2
SATA3G_3
SATA3G_4
SATA3G_1
SATA6G_2
SATA6G_1
ALC
887
PCI3
SPDIF_OUT
SB_PWR
USB1112
USB910
USB78
COM1
16
15
1.5.4
CLRTC
14
13
9
USB56
12
11
PANEL
10
Layout contents
Connectors/Jumpers/Slots/LED
Page Connectors/Jumpers/Slots/LED
Page
CPU,Chassis, and Power fan connectors (4-pin
1.
CPU_FAN, 4-pin CHA_FAN1/2, 3-pin PWR_FAN)
1-25 9.
ATX power connectors (24-pin EATXPWR, 8-pin
2.
EATX12V)
1-27 10. System panel connector (20-8 pin PANEL)
1-30
3. Intel CPU socket
1-8
1-21
4. DDR3 DIMM sockets
1-13 12.
5. GPU Boost switch
1-32 13. Standby Power LED (SB_PWR)
1-33
6. IDE connector (40-1 pin PRI_EIDE)
1-29 14. Digital audio connector (4-1 pin SPDIF_OUT)
1-28
7
1-33 15. Serial port connectors (10-1 pin COM1)
1-24
1-31 16. Front panel audio connector (10-1 pin AAFP)
1-24
®
DRAM LED
8. MemOK! switch
ASUS P8H67-V
Serial ATA connectors (7-pin SATA3G1-4, 7-pin
1-26
SATA6G1-2 )
11. Clear RTC RAM (3-pin CLRTC)
USB connectors (10-1 pin USB56, USB78,
USB910, USB1112)
1-28
1-7
1.6
Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA1155 socket designed for the Intel®
Second Generation Core™ i7 / Core™ i5 / Core™ i3 processors.
Unplug all power cables before installing the CPU.
• Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the
socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing,
or if you see any damage to the PnP cap/socket contacts/motherboard components.
ASUS will shoulder the cost of repair only if the damage is shipment/transit-related.
• Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the
LGA1155 socket.
• The product warranty does not cover damage to the socket contacts resulting from
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP
cap.
1.6.1
Installing the CPU
To install a CPU:
1.
Locate the CPU socket on the motherboard.
P8H67-V
P8H67-V CPU socket LGA1155
2.
Press the load lever with your thumb (A),
and then move it to the right (B) until it is
released from the retention tab.
To prevent damage to the socket pins,
do not remove the PnP cap unless
you are installing a CPU.
Load lever
A
B
Retention tab
1-8
Chapter 1: Product introduction
3.
Lift the load lever in the direction of the
arrow until the load plate is completely
lifted.
Load plate
4.
Remove the PnP cap from the CPU
socket by lifting the tab only.
PnP cap
5.
Position the CPU over the socket,
ensuring that the gold triangle is on the
bottom‑left corner of the socket, and
then fit the socket alignment keys into
the CPU notches.
The CPU fits in only one correct
orientation. DO NOT force the CPU
into the socket to prevent bending
the connectors on the socket and
damaging the CPU!
CPU notches
Gold
triangle
mark
Alignment keys
ASUS P8H67-V
1-9
6.
Apply some Thermal Interface Material
to the exposed area of the CPU that the
heatsink will be in contact with, ensuring
that it is spread in an even thin layer.
Some heatsinks come with preapplied thermal paste. If so, skip this
step.
The Thermal Interface Material is
toxic and inedible. DO NOT eat it. If
it gets into your eyes or touches your
skin, wash it off immediately, and seek
professional medical help.
7.
Close the load plate (A), and then push
down the load lever (B), ensuring that
the front edge of the load plate slides
under the retention knob (C).
B
A
C
8.
1-10
Insert the load lever under the retention
tab.
Chapter 1: Product introduction
1.6.2
Installing the CPU heatsink and fan
The Intel® LGA1155 processor requires a specially designed heatsink and fan assembly to
ensure optimum thermal condition and performance.
• When you buy a boxed Intel® processor, the package includes the CPU fan and
heatsink assembly. If you buy a CPU separately, ensure that you use only Intel®‑certified
multi‑directional heatsink and fan.
• Your Intel® LGA1155 heatsink and fan assembly comes in a push-pin design and
requires no tool to install.
• Use an LGA1155-compatible CPU heatsink and fan assembly only. The LGA1155 socket
is incompatible with the LGA775 and LGA1366 sockets in size and dimension.
If you purchased a separate CPU heatsink and fan assembly, ensure that you have
properly applied Thermal Interface Material to the CPU heatsink or CPU before you install
the heatsink and fan assembly.
Ensure that you have installed the motherboard to the chassis before you install the CPU
fan and heatsink assembly.
To install the CPU heatsink and fan:
1.
Place the heatsink on top of the installed
CPU, ensuring that the four fasteners match
the holes on the motherboard.
A
B
B
A
Orient the heatsink and fan assembly
such that the CPU fan cable is closest to
the CPU fan connector.
2.
Push down two fasteners at a time in a
diagonal sequence to secure the heatsink
and fan assembly in place.
A
B
B
A
1
1
The type of CPU heatsink and fan assembly may differ, but the installation steps and
functions should remain the same. The illustration above is for reference only.
ASUS P8H67-V
1-11
3.
Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN.
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
CPU_FAN
P8H67-V
P8H67-V CPU fan connector
Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if
you fail to plug this connector.
1.6.3
Uninstalling the CPU heatsink and fan
To uninstall the CPU heatsink and fan:
1. Disconnect the CPU fan cable from the connector on the motherboard.
2.
Rotate each fastener counterclockwise.
3.
Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and
fan assembly from the motherboard.
A
A
B
B
B
A
B
1-12
A
Chapter 1: Product introduction
4.
Carefully remove the heatsink and fan
assembly from the motherboard.
5.
Rotate each fastener clockwise to ensure
correct orientation when reinstalling.
1.7
System memory
1.7.1
Overview
DIMM_B1
DIMM_B2
DIMM_A1
DIMM_A2
The motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules
(DIMM) sockets.
A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched
differently to prevent installation on a DDR2 DIMM socket. DDR3 modules are developed for
better performance with less power consumption.
The figure illustrates the location of the DDR3 DIMM sockets:
P8H67-V
Channel
Sockets
Channel A
DIMM_A1 and DIMM_A2
Channel B
DIMM_B1 and DIMM_B2
P8H67-V 240-pin DDR3 DIMM sockets
ASUS P8H67-V
1-13
1.7.2
Memory configurations
You may install 512MB, 1GB, 2GB, and 4GB unbuffered non‑ECC DDR3 DIMMs into the
DIMM sockets.
• You may install varying memory sizes in Channel A and Channel B. The system maps
the total size of the lower-sized channel for the dual-channel configuration. Any excess
memory from the higher-sized channel is then mapped for single-channel operation.
• According to Intel CPU specification, DIMM voltage below 1.65V is recommended to
protect the CPU.
• According to Intel CPU specification, CPUs with a core frequency of 2.66GHz support
the maximum DIMM frequency of up to DDR3 1333. To use DIMMs of a higher
frequency with a 2.66GHz CPU, adjust the Memory Frequency item in BIOS. Refer to
section 2.4.2 Memory Frequency for details.
• Always install DIMMs with the same CAS latency. For optimum compatibility, we
recommend that you obtain memory modules from the same vendor.
• Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
- Use a maximum of 3GB system memory if you are using a 32-bit Windows® OS.
- Install a 64-bit Windows® OS when you want to install 4GB or more on the
motherboard.
• This motherboard does not support DIMMs made up of 512Mb (64MB) chips or less.
• The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a
lower frequency than the vendor-marked value. To operate at the vendor-marked or at a
higher frequency, refer to section 2.4 Ai Tweaker menu for manual memory frequency
adjustment.
• For system stability, use a more efficient memory cooling system to support a full
memory load (4 DIMMs) or overclocking condition.
• The Max. 32GB memory capacity can be supported with DIMMs of 8GB (or above).
ASUS will update the QVL once the DIMMs are available on market.
• Visit the ASUS website at www.asus.com for the latest QVL.
1-14
Chapter 1: Product introduction
P8H67-V Motherboard Qualified Vendors List (QVL)
DDR3-1333MHz capability
Size
SS/
DS
Chip
Brand
1GB
SS
A-Data
Vendors
Part No.
A-Data
AD31333001GOU
A-Data
AD31333G001GOU
A-Data
AD31333002GOU
2GB
DS
A-Data
A-Data
AD31333G002GMU
2GB
DS
-
Apacer
78.A1GC6.9L1
2GB
DS
Apacer
78.A1GC6.9L1
2GB
CORSAIR
CM3X1024-1333C9DHX
CORSAIR
CM3X1024-1333C9
CORSAIR
TR3X3G1333C9 G
CORSAIR
TR3X3G1333C9 G
CORSAIR
TR3X3G1333C9
CORSAIR
CMD24GX3M6A1333C9(XMP)
CORSAIR
CM3X2048-1333C9DHX
CORSAIR
CORSAIR
Crucial
CT12864BA1339.8FF
1GB
SS
Crucial
CT25664BA1339.16FF
2GB
Crucial
BL25664BN1337.16FF (XMP)
ELPIDA
Chip No.
Timing
Voltage
DIMM
support
A* B* C*
AD30908C8D-151C E0906 -
-
•
•
-
1.65-1.85V •
•
AD30908C8D-151C E0903 -
-
•
•
•
-
8-8-8-24
1.65-1.85V •
•
•
APACER
AM5D5808DEWSBG
-
-
•
•
•
DS
Apacer
AM5D5808FEQSBG
9
-
•
•
•
1GB
SS
-
-
9-9-9-24
1.60V
•
•
1GB
SS
-
-
9-9-9-24
1.60V
•
•
3GB(3 x 1GB) SS
-
-
9-9-9-24
1.50V
•
•
3GB(3 x 1GB) SS
-
-
9-9-9-24
1.50V
•
•
3GB(3 x 1GB) SS
-
-
9-9-9-24
1.50V
•
•
•
24GB(6x4GB) DS
-
-
9-9-9-24
1.60V
•
•
•
3GB(3 x 1GB) SS
-
8-8-8-24
•
•
2GB
DS
-
-
-
-
•
•
TW3X4G1333C9 G
4GB(2x2GB)
DS
-
-
9-9-9-24
1.50V
•
•
•
CMX8GX3M4A1333C9
8GB(4 x 2GB) DS
-
-
9-9-9-24
1.50V
•
•
•
Micron
9FF22D9KPT
9
-
•
•
•
DS
Micron
9KF27D9KPT
9
-
•
•
•
6GB(3x2GB)
DS
-
-
7-7-7-24
1.65V
•
•
•
EBJ10UE8EDF0-DJ-F
1GB
SS
ELPIDA
J1108EDSE-DJ-F
-
1.35V(low
voltage)
•
•
•
ELPIDA
EBJ21UE8EDF0-DJ-F
2GB
DS
ELPIDA
J1108EDSE-DJ-F
-
1.35V(low
voltage)
•
•
G.SKILL
F3-10600CL8D-2GBHK(XMP)
1GB
SS
G.SKILL
-
-
-
•
•
•
G.SKILL
F3-10666CL7T-3GBPK(XMP)
3GB(3 x 1GB) SS
-
-
7-7-7-18
1.5~1.6V
•
•
•
G.SKILL
F3-10666CL9T-3GBNQ
3GB(3 x 1GB) SS
-
-
9-9-9-24
1.5~1.6V
•
•
G.SKILL
F3-10600CL9D-2GBNQ
1GB
DS
G.SKILL
-
-
-
G.SKILL
F3-10600CL8D-4GBHK(XMP)
4GB(2x2GB)
DS
-
-
8-8-8-21
1.5-1.6V
•
•
G.SKILL
F3-10666CL8D-4GBECO(XMP)
4GB(2x2GB)
DS
-
-
8-8-8-8-24 XMP 1.35V •
•
G.SKILL
F3-10666CL7T-6GBPK(XMP)
6GB(3x2GB)
DS
-
-
7-7-7-18
1.5~1.6V
•
•
•
G.SKILL
F3-10666CL7D-8GBRH(XMP)
8GB(2 x 4GB) DS
-
-
7-7-7-21
1.5V
•
•
•
GEIL
GET316GB1333C9QC
DS
-
-
9-9-9-24
1.5V
•
•
GEIL
GV32GB1333C9DC
2GB(2 x 1GB) DS
-
-
9-9-9-24
1.5V
•
•
•
GEIL
GV34GB1333C7DC
2GB
DS
-
-
7-7-7-24
1.5V
•
•
GEIL
GG34GB1333C9DC
4GB(2x2GB)
DS
GEIL
GL1L128M88BA12N
9-9-9-24
1.3V(low
voltage)
•
•
GEIL
GV34GB1333C9DC
4GB(2x2GB)
DS
-
-
9-9-9-24
1.5V
•
•
•
Hynix
HMT112U6TFR8A-H9
1GB
SS
HYNIX
H5TC1G83TFRH9A
-
1.35V(low
voltage)
•
•
•
Hynix
HMT125U6TFR8A-H9
2GB
DS
HYNIX
H5TC1G83TFRH9A
-
1.35V(low
voltage)
•
•
•
KINGMAX
FLFD45F-B8KL9
1GB
SS KINGMAX KKB8FNWBFGNX-27A
-
-
•
•
•
KINGMAX
FLFE85F-C8KM9-NAES
2GB
SS KINGMAX KFC8FNMXF-BXX-15A
-
-
•
•
•
KINGMAX
FLFE85F-B8KL9
2GB
DS KINGMAX KKB8FNWBFGNX-26A
-
-
•
•
•
KINGMAX
FLFF65F-C8KM9-NEES
4GB
DS KINGMAX KFC8FNMXF-BXX-15A
-
-
•
•
•
Kingston
KVR1333D3N9/1G
1GB
SS
ELPIDA
J1108BDBG-DJ-F
9
1.5V
•
•
•
KINGSTON
KVR1333D3N9/2G(low profile)
2GB
DS
ELPIDA
J1108BDBG-DJ-F
9
1.5V
•
•
•
Kingston
KVR1333D3N9/2G
2GB
DS
KTC
D1288JPNDPLD9U
9
1.5V
•
•
•
Kingston
KVR1333D3N9/2G
2GB
DS
ELPIDA
J1108BDSE-DJ-F
9
1.5V
•
•
•
Kingston
KHX1333C7D3K2/4GX(XMP)
4GB(2x2GB)
DS
-
-
7
1.65V
•
•
•
Kingston
KHX1333C9D3UK2/4GX(XMP)
4GB(2x2GB)
DS
-
-
9
XMP 1.25V •
•
•
KINGSTON
KVR1333D3N9/4G(low profile)
4GB
DS
HYNIX
H5TQ2G83AFRH9C
9
1.5V
•
•
•
KINGSTON
KVR1333D3N9/4G
4GB
DS
Hynix
H5TQ2G83AFR
-
-
•
•
•
MICRON
MT4JTF12864AZ-1G4D1
1GB
SS
MICRON
D9LGQ
-
-
•
•
•
Micron
MT8JTF12864AZ-1G4F1
1GB
SS
Micron
9FF22D9KPT
9
-
•
•
•
16GB
(4x4GB )
continued on the next page
ASUS P8H67-V
1-15
DDR3-1333MHz capability
1-16
SS/
DS
Chip
Brand
2GB
SS
MICRON
2GB
DS
Micron
4GB
DS
MICRON
OCZ3F13334GK
4GB(2x2GB)
DS
OCZ
OCZ3G1333LV4GK
4GB(2x2GB)
OCZ
OCZ3P1333LV4GK
OCZ
OCZ3X13334GK(XMP)
OCZ
Vendors
Part No.
Size
MICRON
MT8JTF25664AZ-1G4D1
Micron
MT16JTF25664AZ-1G4F1
MICRON
MT16JTF51264AZ-1G4D1
OCZ
Chip No.
Timing
Voltage
DIMM
support
D9LGK
-
-
A* B* C*
•
•
•
9KF27D9KPT
9
-
•
•
•
D9LGK
-
-
•
•
•
-
-
9-9-9-20
1.7V
•
•
•
DS
-
-
9-9-9-20
1.65V
•
•
4GB(2x2GB)
DS
-
-
7-7-7-20
1.65V
•
•
•
4GB(2x2GB)
DS
-
-
7-7-7-20
1.75V
•
•
•
OCZ3G1333LV6GK
6GB(3x2GB)
DS
-
-
9-9-9-20
1.65V
•
•
OCZ
OCZ3P1333LV6GK
6GB(3x2GB)
DS
-
-
7-7-7-20
1.65V
•
OCZ
OCZ3X1333LV6GK(XMP)
6GB(3x2GB)
DS
-
-
8-8-8-20
1.60V
•
•
•
OCZ
OCZ3G1333LV8GK
8GB (2x4GB) DS
-
-
9-9-9-20
1.65V
•
•
•
OCZ
OCZ3RPR1333C9LV8GK
8GB (2x4GB) DS
-
-
9-9-9-20
1.65V
•
PSC
AL7F8G73D-DG1
1GB
SS
PSC
A3P1GF3DGF928M9B05
8-8-8-24
1.5V
•
•
•
PSC
AL8F8G73D-DG1
2GB
DS
PSC
A3P1GF3DGF928M9B05
8-8-8-24
1.5V
•
•
•
SAMSUNG
M378B2873DZ1-CH9
1GB
846 HCH9
SS SAMSUNG SEC
K4B1G08460
-
-
•
•
•
SAMSUNG
M378B2873EH1-CH9
1GB
SS
913 HCH9
Samsung SEC
K4B1G0846E
-
-
•
•
•
SAMSUNG
M378B2873FHS-CH9
1GB
SS SAMSUNG K4B1G0846F
-
-
•
•
SAMSUNG
M378B5673DZ1-CH9
2GB
DS
Samsung K4B1G0846D-HCH9
-
-
•
•
•
SAMSUNG
M378B5673EH1-CH9
2GB
DS
913 HCH9
Samsung SEC
K4B1G0846E
-
-
•
•
•
SAMSUNG
M378B5673FH0-CH9
2GB
DS SAMSUNG K4B1G0846F
-
-
•
•
•
SAMSUNG
M378B5273CH0-CH9
4GB
DS SAMSUNG K4B2G0846C
-
-
•
•
•
Super Talent W1333UA1GH
1GB
SS
9
-
•
•
•
Super Talent W1333UB2GS
2GB
DS
Samsung K4B1G0846F
9
-
•
•
•
Super Talent W1333UB4GS
4GB
DS
Samsung K4B2G0846C
-
-
•
•
•
Super Talent W1333UX6GM
6GB(3x2GB)
DS
Micron
0BF27D9KPT
9-9-9-24
1.5V
•
•
•
HYNIX
H5TQ1G83TFR
•
Transcend
TS256MLK64V3U
2GB
DS
Micron
9GF27D9KPT
-
-
•
•
•
Transcend
TS256MLK64V3U
2GB
DS
Elpida
J1108BDBG-DJ-F
9
-
•
•
•
Elixir
M2F2G64CB88B7N-CG
2GB
DS
Elixir
N2CB2G808N-CG
-
-
Elixir
M2Y2G64CB8HA9N-CG
2GB
DS
-
-
7-7-7-20
-
•
•
•
Elixir
M2Y2G64CB8HC9N-CG
2GB
DS
Elixir
-
-
-
•
•
•
Elixir
M2F4G64CB8HB5N-CG
4GB
DS
Elixir
N2CB2G808N-CG
-
-
•
•
•
KINGSHARE KSRPCD313332G
2GB
DS
PATRIOT PM128M8D385-15
-
-
•
•
•
Kingtiger
KTG2G1333PG3
2GB
DS
-
-
-
-
•
•
•
PATRIOT
PSD31G13332H
1GB
DS
-
-
9
-
•
•
•
PATRIOT
PSD31G13332
1GB
DS
Patriot
PM64M8D38U-15
-
-
•
•
•
PATRIOT
PSD32G13332H
2GB
DS
-
-
-
-
•
•
•
RAMAXEL
RMR1870ED48E8F-1333
2GB
DS
ELPIDA
J1108BDBG-DJ-F
-
-
•
•
•
SILICON
POWER
SP001GBLTU133S01
1GB
SS
NANYA
NT5CB128M8AN-CG
9
-
•
•
•
SILICON
POWER
SP001GBLTU133S02
1GB
SS
elixir
N2CB1680AN-C6
9
-
•
•
•
SILICON
POWER
SP002GBLTU133S02
2GB
DS
elixir
N2CB1680AN-C6
9
-
•
•
•
TAKEMS
TMS1GB364D081-107EY
1GB
SS
-
-
7-7-7-20
1.5V
•
•
TAKEMS
TMS2GB364D082-138EW
2GB
DS
-
-
8-8-8-24
1.5V
•
•
UMAX
E41302GP0-73BDB
2GB
DS
UMAX
U2S24D30TP-13
-
-
•
•
WINTEC
3WVS31333-2G-CNR
2GB
DS
AMPO
AM3420803-13H
-
-
•
•
•
Chapter 1: Product introduction
•
DDR3-1066MHz capability
Vendors
Part No.
Size
SS/DS
Chip
Brand
Crucial
Crucial
CT12864BA1067.8FF
CT25664BA1067.16FF
1GB
2GB
SS
DS
Micron
Micron
9GF22D9KPT
9HF22D9KPT
7
7
ELPIDA
EBJ10UE8EDF0-AE-F
1GB
SS
ELPIDA
J1108EDSE-DJ-F
-
ELPIDA
EBJ11UD8BAFA-AE-E
1GB
DS
Elpida
J5308BASE-AC-E
-
ELPIDA
EBJ21UE8EDF0-AE-F
2GB
DS
ELPIDA
J1108EDSE-DJ-F
-
KINGSTON
KINGSTON
KINGSTON
Micron
Micron
OCZ
KVR1066D3N7/1G
KVR1066D3N7/2G
KVR1066D3N7/4G
MT8JTF12864AZ-1G1F1
MT16JTF25664AZ-1G1F1
OCZ3G1066LV4GK
1GB
2GB
4GB
1GB
2GB
4GB(2x2GB)
SS
DS
DS
SS
DS
DS
KTC
ELPIDA
Hynix
Micron
Micron
Micron
SAMSUNG
M378B2873EH1-CF8
1GB
SS
SAMSUNG
Elixir
Elixir
Kingtiger
M378B5273BH1-CF8
M2Y2G64CB8HC5N-BE
M2Y2G64CBHA9N-BE
2GB DIMM PC3-8500
4GB
2GB
2GB
2GB
DS
DS
DS
DS
Chip No.
D1288JPNDPLD9U
J1108BDSE-DJ-F
H5TQ2G83AFR
9GF22D9KPT
9HF22D9KPT
9BF27D9KPV
901 HCF8
Samsung SEC
K4B1G0846E
SAMSUNG 846 K4B2G0846B-HCF8
Elixir
N2CB1G80CN-BE
Hynix
H5TQ1G83AFP G7C
Timing
Voltage
DIMM
support
A* B* C*
1.35V(low
voltage)
1.35V(low
voltage)
1.5V
1.5V
1.5V
1.65V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
-
-
•
•
•
7-7-7-20
-
-
•
•
•
•
•
•
•
•
•
•
•
7
7
7
7
7
7-7-7-20
SS: Single-sided / DS: Double-sided
DIMM support:
• A*: one (1) module inserted into any slot as single-channel memory configuration. We
suggest that you install the module into A2 slot.
• B*: two (2) modules inserted into either the blue slots or the black slots as one pair of
dual-channel memory configuration. We suggest that you install the modules into
slots A2 and B2 for better compatibility.
• C*: four (4) modules inserted into both the blue slots and the black slots as two pairs of
dual-channel memory configuration.
ASUS P8H67-V
1-17
1.7.3
Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other system components.
Failure to do so can cause severe damage to both the motherboard and the components.
2
1.
Press the retaining clips outward to
unlock a DIMM socket.
2.
Align a DIMM on the socket such that
the notch on the DIMM matches the
DIMM slot key on the socket.
DIMM notch
1
1
DIMM slot key
Unlocked retaining clip
A DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into
a socket in the wrong direction to avoid damaging the DIMM.
3.
Firmly insert the DIMM into the socket
until the retaining clips snap back in place
and the DIMM is properly seated.
3
Locked Retaining Clip
1.7.4
Removing a DIMM
To remove a DIMM:
1.
Simultaneously press the retaining clips
outward to unlock the DIMM.
2
Support the DIMM lightly with your
fingers when pressing the retaining
clips. The DIMM might get damaged
when it flips out with extra force.
1
1
DIMM notch
2.
1-18
Remove the DIMM from the socket.
Chapter 1: Product introduction
1.8
Expansion slots
In the future, you may need to install expansion cards. The following sub‑sections describe
the slots and the expansion cards that they support.
Unplug the power cord before adding or removing expansion cards. Failure to do so may
cause you physical injury and damage motherboard components.
1.8.1
Installing an expansion card
To install an expansion card:
1.
Before installing the expansion card, read the documentation that came with it and
make the necessary hardware settings for the card.
2.
Remove the system unit cover (if your motherboard is already installed in a chassis).
3.
Remove the bracket opposite the slot that you intend to use. Keep the screw for later
use.
4.
Align the card connector with the slot and press firmly until the card is completely
seated on the slot.
5.
Secure the card to the chassis with the screw you removed earlier.
6.
Replace the system cover.
1.8.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for
information on BIOS setup.
2.
Assign an IRQ to the card.
3.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that
the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI
groups, making the system unstable and the card inoperable.
1.8.3
PCI slots
1.8.4
PCI Express x1 slots
1.8.5
PCI Express x16 slots
The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that
comply with PCI specifications.
This motherboard supports PCI Express x1 network cards, SCSI cards, and other cards that
comply with the PCI Express specifications.
This motherboard has two PCI Express 2.0 x16 slots that support PCI Express x16 2.0
graphic cards complying with the PCI Express specifications.
ASUS P8H67-V
1-19
VGA configuration
PCI Express operating mode
PCIe x16_1
PCIe x16_2
Single VGA/PCIe card
x16 (Recommended for single VGA card)
N/A
Dual VGA/PCIe card
x16
x4
• In single VGA card mode, use the PCIe 2.0 x16_1 slot (blue) for a PCI Express x16
graphics card to get better performance.
• PCIe x1 slot shares the bandwidth with PCIe x16_2 slot. Due to CrossFireX™ limitation,
DO NOT use the PCIe x1 slot when you install two CrossFireX™ graphics cards on both
the PCIe x16 slots to set up a CrossFireX™ cofiguration. To disable the PCIe x1 slot,
refer to the Onboard Devices Configuration section in the BIOS for details.
• We recommend that you provide sufficient power when running CrossFireX™ mode.
See page 1-27 for details.
• Connect a chassis fan to the motherboard connector labeled CHA_FAN1 or CHA_FAN2
when using multiple graphics cards for better thermal environment.
1-20
Chapter 1: Product introduction
1.9
1.
Jumpers
Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
clear the CMOS memory of date, time, and system setup parameters by erasing
the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in
CMOS, which include system setup information such as system passwords.
P8H67-V
CLRTC
1
2
2
3
Normal
(Default)
Clear RTC
P8H67-V Clear RTC RAM
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3
for about 5-10 seconds, then move the cap back to pins 1-2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter
data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default
position. Removing the cap will cause system boot failure!
• If the steps above do not help, remove the onboard battery and move the jumper again
to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.
• You do not need to clear the RTC when the system hangs due to overclocking. For
system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature. Shut
down and reboot the system, then the BIOS automatically resets parameter settings to
default values.
ASUS P8H67-V
1-21
1.10
Connectors
1.10.1
Rear panel connectors
1
2
3
15
14
13
4
12
11
5 6 7 8
10
9
1.
PS/2 Keyboard/Mouse COMBO port. This port is for a PS/2 keyboard/mouse.
2.
Optical S/PDIF Out port. This port connects an external audio output device via an
optical S/PDIF cable.
3.
Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other
VGA-compatible devices.
4.
LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)
through a network hub. Refer to the table on the next page for the LAN port LED
indicators.
LAN port LED indications
ACT/LINK LED
SPEED LED
Status
Description
Status
Description
OFF
No link
OFF
10 Mbps connection
ORANGE
Linked
ORANGE
100 Mbps connection
BLINKING
Data activity
GREEN
1 Gbps connection
ACT/LINK SPEED
LED
LED
LAN port
5.
Center / Subwoofer port (orange). This port connects the center/subwoofer speakers.
6.
Rear Speaker Out port (black). This port connects the rear speakers in a 4-channel,
6-channel, or 8-channel audio configuration.
7.
Line In port (light blue). This port connects the tape, CD, DVD player, or other audio
sources.
8.
Line Out port (lime). This port connects a headphone or a speaker. In 4-channel, 6channel, and 8-channel configurations, the function of this port becomes Front Speaker
Out.
9.
Microphone port (pink). This port connects a microphone.
10. Side Speaker Out port (gray). This port connects the side speaker in an 8-channel
audio configuration.
Refer to the audio configuration table on the next page for the function of the audio ports in
the 2, 4, 6, or 8-channel configuration.
1-22
Chapter 1: Product introduction
Audio 2, 4, 6, and 8-channel configuration
Port
Headset 2-channel
4-channel
6-channel
Light Blue
Line In
Line in
Line in
Line in
Lime
Line Out
Front Speaker Out
Front Speaker Out
Front Speaker Out
11.
8-channel
Pink
Mic In
Mic In
Mic in
Mic in
Orange
-
-
Center/Subwoofer
Center/Subwoofer
Black
-
Rear Speaker Out
Rear Speaker Out
Rear Speaker Out
Gray
-
-
-
Side Speaker Out
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports connect to
USB 2.0/1.1 devices.
12. USB 3.0 ports 1 and 2. These two 9-pin Universal Serial Bus (USB) ports connect to
USB 3.0/2.0 devices.
• DO NOT connect a keyboard / mouse to any USB 3.0 port when installing an operating
system.
• Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows®
OS environment and after the USB 3.0 driver installation.
• USB 3.0 devices can only be used as data storage only.
• We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster
and better performance for your USB 3.0 devices.
13. DVI port. This port is for any DVI-D compatible device. DVI-D can’t be converted to
output RGB Signal to CRT and isn’t compatible with DVI-I.
14. HDMI port. This port is for a High-Definition Multimedia Interface (HDMI) connector,
and is HDCP compliant allowing playback of HD DVD, Blu-Ray and other protected
content.
Dual display output support
• This table indicates that whether the following dual display outputs are supported for
your motherboard:
Dual display outputs
Supported
DVI + D-Sub
•
DVI + HDMI
•
HDMI + D-Sub
•
Not supported
•During POST, only the monitor connected to the D-Sub port has display. The dual
display function works only under Windows.
15. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports connect to
USB 2.0/1.1 devices.
ASUS P8H67-V
1-23
1.10.2
1.
Internal connectors
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports
either High Definition Audio or AC`97 audio standard. Connect one end of the front
panel audio I/O module cable to this connector.
AAFP
P8H67-V
NC
PORT2 L
SENSE_SEND
NC
PORT2 R
NC
PORT1 R
AGND
PORT1 L
SENSE2_RETUR
SENSE1_RETUR
PRESENCE#
GND
PIN 1
HD-audio-compliant
pin definition
Line out_L
NC
Line out_R
MICPWR
MIC2
PIN 1
Legacy AC’97
compliant definition
P8H67-V Front panel audio connector
If you want to connect a high-definition front panel audio module to this connector, ensure
that the Front Panel Type item in the BIOS is set to [HD Audio]. If you want to connect an
AC97 front panel audio module to this connector, set the item to [AC97]. See section 2.5.6
Onboard Devices Configuration for details.
2.
Serial port connectors (10-1 pin COM1)
The connector is for a serial (COM) port. Connect the serial port module cable to the
connector, then install the module to a slot opening at the back of the system chassis.
The serial port bracket (COM1) is purchased separately.
COM1
PIN 1
P8H67-V
P8H67-V Serial port (COM1) connector
1-24
Chapter 1: Product introduction
3.
CPU, Chassis, and Power fan connectors (4-pin CPU_FAN, 3-pin PWR_FAN, 4-pin
CHA_FAN1 and CHA_FAN2)
Connect the fan cables to the fan connectors on the motherboard, making sure that the
black wire of each cable matches the ground pin of the connector.
DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside
the system may damage the motherboard components. They are not jumpers! DO NOT
place jumper caps on the fan connectors.
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
CPU_FAN
P8H67-V
CHA_FAN2
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
CHA_FAN1
GND
CPU FAN PWR
CPU FAN IN
CPU FAN PWM
PWR_FAN
GND
+12V
Rotation
P8H67-V fan connectors
• The CPU_FAN connector supports a CPU fan of maximum 2A (24 W) fan power.
• Only the CPU_FAN, CHA_FAN1 and CHA_FAN2 connectors support the ASUS Fan
Xpert feature.
• If you install two VGA cards, we recommend that you plug the rear chassis fan cable
to the motherboard connector labeled CHA_FAN1 or CAH_FAN 2 for better thermal
environment.
ASUS P8H67-V
1-25
4.
Serial ATA connectors (7-pin SATA3G1-4, 7-pin SATA6G1-2)
These connectors are for the Serial ATA signal cables for Serial ATA 3Gb/s or 6Gb/s
hard disk and optical disk drives.
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
SATA3G_1
SATA6G_2
SATA6G_1
GND
RSATA_RXN2
RSATA_RXP2
GND
RSATA_TXN2
RSATA_TXP2
GND
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
SATA3G_4
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA3G_3
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
P8H67-V
SATA3G_2
P8H67-V SATA connectors
• These connectors are set to [AHCI Mode] by default. If you intend to create a Serial ATA
RAID set using these connectors, set the SATA Mode item in the BIOS to [RAID Mode].
See section 2.5.4 SATA Configuration for details.
• Before creating a RAID set, refer to the RAID Supplementary Guide included in the
folder named Manual in the support DVD.
• You must install Windows® XP Service Pack 2 or later version before using Serial ATA
hard disk drives. The Serial ATA RAID feature (RAID 0, 1, 5, and 10) is available only if
you are using Windows® XP SP2 or later version.
• When using hot-plug and NCQ, set the SATA Mode item in the BIOS to [AHCI Mode].
See section 2.5.4 SATA Configuration for details.
1-26
Chapter 1: Product introduction
5.
ATX power connectors (24-pin EATXPWR, 8-pin ATX12V)
These connectors are for an ATX power supply. The plugs from the power supply are
designed to fit these connectors in only one orientation. Find the proper orientation and
push down firmly until the connectors completely fit.
+12V DC
+12V DC
+12V DC
+12V DC
EATX12V
GND
GND
GND
GND
P8H67-V
EATXPWR
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
GND
PIN 1
+5 Volts
GND
+5 Volts
GND
+3 Volts
+3 Volts
GND
+5 Volts
+5 Volts
+5 Volts
-5 Volts
GND
GND
GND
PSON#
GND
-12 Volts
+3 Volts
PIN 1
P8H67-V ATX power connectors
• For a fully configured system, we recommend that you use a power supply unit (PSU)
that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum
power of 350 W.
• DO NOT forget to connect the 4-pin / 8-pin ATX +12V power plug. Otherwise, the system
will not boot up.
• We recommend that you use a PSU with higher power output when configuring a
system with more power-consuming devices or when you intend to install additional
devices. The system may become unstable or may not boot up if the power is
inadequate.
• If you are uncertain about the minimum power supply requirement for your system,
refer to the Recommended Power Supply Wattage Calculator at http://support.asus.
com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.
ASUS P8H67-V
1-27
6.
USB connectors (10-1 pin USB56, USB78, USB910, USB1112)
These connectors are for USB 2.0 ports. Connect the USB module cable to any of
these connectors, then install the module to a slot opening at the back of the system
chassis. These USB connectors comply with the USB 2.0 specification that supports up
to 480Mbps connection speed.
USB+5V
USB_P7
USB_P7+
GND
PIN 1PIN 1
USB+5V
USB_P8USB_P8+
GND
NC
USB56
USB+5V
USB_P10USB_P10+
GND
NC
PIN 1
USB+5V
USB_P9USB_P9+
GND
PIN 1
USB+5V
USB_P11USB_P11+
GND
USB+5V
USB_P13USB_P13+
GND
USB78
USB+5V
USB_P12USB_P12+
GND
NC
USB910
USB+5V
USB_P14USB_P14+
GND
NC
USB1112
P8H67-V
P8H67-V USB2.0 connectors
Never connect a 1394 cable to the USB connectors. Doing so will damage the
motherboard!
The USB 2.0 module is purchased separately.
7.
Digital audio connector (4-1 pin SPDIF_OUT)
+5V
P8H67-V
SPDIFOUT
GND
This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port.
SPDIF_OUT
P8H67-V Digital audio connector
The S/PDIF module is purchased separately.
1-28
Chapter 1: Product introduction
8.
IDE connector (40-1 pin PRI_EIDE)
The onboard IDE connector is for Ultra DMA 133/100 signal cable. There are three
connectors on each Ultra DMA 133/100 signal cable: blue, black, and gray. Connect
the blue connector to the motherboard’s IDE connector, then select one of the following
modes to configure your devices:
Single device
Drive jumper setting
Mode of device(s)
Cable connector
Cable-Select or Master
-
Black
Master
Black
Slave
Gray
Cable-Select
Two devices
Master
Master
Slave
Slave
Black or gray
• Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA
cable connector. This prevents incorrect insertion when you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra DMA 133/100 IDE devices.
If any device jumper is set as “Cable-Select”, ensure that all other device jumpers have the
same setting.
PRI_EIDE
PIN1
P8H67-V
NOTE:Orient the red markings
on the IDE ribbon cable to PIN 1.
P8H67-V IDE connector
ASUS P8H67-V
1-29
9.
System panel connector (20-8 pin PANEL)
This connector supports several chassis-mounted functions.
SPEAKER
+5V
Ground
Ground
Speaker
PLED-
PLED+
PLED
PANEL
IDE_LED
PWRSW
Reset
Ground
PWR
Ground
PIN 1
IDE_LED+
IDE_LED-
P8H67-V
RESET
* Requires an ATX power supply
P8H67-V System panel connector
•
System power LED (2-pin PLED)
•
This 2-pin connector is for the system power LED. Connect the chassis power LED
cable to this connector. The system power LED lights up when you turn on the system
power, and blinks when the system is in sleep mode.
Hard disk drive activity LED (2-pin IDE_LED)
•
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable
to this connector. The IDE LED lights up or flashes when data is read from or written to
the HDD.
System warning speaker (4-pin SPEAKER)
•
This 4-pin connector is for the chassis-mounted system warning speaker. The speaker
allows you to hear system beeps and warnings.
ATX power button/soft-off button (2-pin PWRSW)
•
This 2-pin connector is for the system power button.
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without
turning off the system power.
1-30
Chapter 1: Product introduction
1.11
Onboard switches
Onboard switches allow you to fine-tune performance when working on a bare or open-case
system. This is ideal for overclockers and gamers who continually change settings to
enhance system performance.
1.
MemOK! switch
Installing DIMMs that are incompatible with the motherboard may cause system boot failure,
and the DRAM_LED near the MemOK! switch lights continuously. Press and hold the
MemOK! switch until the DRAM_LED starts blinking to begin automatic memory compatibility
tuning for successful boot.
P8H67-V
P8H67-V MemOK! switch
• Refer to section 1.12 Onboard LEDs for the exact location of the DRAM_LED.
• The DRAM_LED also lights when the DIMM is not properly installed. Turn off the system
and reinstall the DIMM before using the MemOK! function.
• The MemOK! switch does not function under Windows® OS environment.
• During the tuning process, the system loads and tests failsafe memory settings. It takes
about 30 seconds for the system to test one set of failsafe settings. If the test fails,
the system reboots and test the next set of failsafe settings. The blinking speed of the
DRAM_LED increases, indicating different test processes.
• Due to memory tuning requirement, the system automatically reboots when each timing
set is tested. If the installed DIMMs still fail to boot after the whole tuning process, the
DRAM_LED lights continuously. Replace the DIMMs with ones recommended in the
Memory QVL (Qualified Vendors Lists) in this user manual or on the ASUS website at
www.asus.com.
• If you turn off the computer and replace DIMMs during the tuning process, the system
continues memory tuning after turning on the computer. To stop memory tuning, turn off
the computer and unplug the power cord for about 5–10 seconds.
• If your system fail to boot due to BIOS overclocking, press the MemOK! switch to boot
and load BIOS default settings. A message will appear during POST reminding you that
the BIOS has been restored to its default settings.
• We recommend that you download and update to the latest BIOS version from the
ASUS website at www.asus.com after using the MemOK! function.
ASUS P8H67-V
1-31
2.
GPU Boost switch
This switch allows you to enable or disable the GPU Boost function.
GPU Boost
P8H67-V
P8H67-V GPU Boost switch
1-32
Chapter 1: Product introduction
1.12
1.
Onboard LEDs
Standby Power LED
The motherboard comes with a standby power LED that lights up to indicate that the
system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should
shut down the system and unplug the power cable before removing or plugging in any
motherboard component. The illustration below shows the location of the onboard LED.
P8H67-V
SB_PWR
ON
Standby Power
OFF
Powered Off
P8H67-V Onboard LED
2.
DRAM LED
DRAM LED checks the DRAM in sequence during motherboard booting process. If an
error is found , the LED next to the error device will continue lighting until the problem
is solved. This user-friendly design provides an intuitional way to locate the root
problem within a second.
DRAM LED
P8H67-V
P8H67-V DRAM LED
ASUS P8H67-V
1-33
1.13
Software support
1.13.1
Installing an operating system
This motherboard supports Windows® XP / Vista / 7 Operating Systems (OS). Always install
the latest OS version and corresponding updates to maximize the features of your hardware.
• Motherboard settings and hardware options vary. Refer to your OS documentation for
detailed information.
• Ensure that you install Windows® XP Service Pack 3 or later versions / Windows® Vista
Service Pack 1 or later versions before installing the drivers for better compatibility and
system stability.
1.13.2
Support DVD information
The Support DVD that comes with the motherboard package contains the drivers, software
applications, and utilities that you can install to avail all motherboard features.
The contents of the Support DVD are subject to change at any time without notice. Visit the
ASUS website at www.asus.com for updates.
To run the Support DVD
Place the Support DVD to the optical drive. The DVD automatically displays the Drivers menu
if Autorun is enabled in your computer.
The following screen is for reference only.
Click an icon to
display Support
DVD/motherboard
information
Click an item to install
If Autorun is NOT enabled in your computer, browse the contents of the Support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the DVD.
1-34
Chapter 1: Product introduction
Chapter 2
BIOS information
2.1
Managing and updating your BIOS
Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to
restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update
utility.
2.1.1
ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update the motherboard
BIOS in Windows® environment.
• ASUS Update requires an Internet connection either through a network or an Internet
Service Provider (ISP).
• This utility is available in the support DVD that comes with the motherboard package.
Installing ASUS Update
To install ASUS Update:
1.
Place the support DVD in the optical drive. The Drivers menu appears.
2.
Click the Utilities tab, then click AI Suite II.
3.
Follow the onscreen instructions to complete the installation.
Quit all Windows® applications before you update the BIOS using this utility.
Updating the BIOS
To update the BIOS:
1.
From the Windows® desktop, click Start > Programs > ASUS > AI Suite II > AI Suite
II X.XX.XX to launch the AI Suite II utility. The AI Suite II Quick Bar appears.
2.
Click Update button from the Quick Bar, and then click ASUS Update from the popup
menu. The ASUS Update main screen appears. From the list, select either of the
following methods:
Updating from the Internet
a.
Select Update BIOS from the Internet, then click Next.
b.
Select the ASUS FTP site nearest you to avoid network traffic, then click Next.
c.
From the FTP site, select the BIOS version that you wish to download then click Next.
Chapter 2: BIOS information
2-1
The ASUS Update utility is capable of updating itself through the Internet. Always update
the utility to avail all its features.
Updating from a BIOS file
a.
Select Update BIOS from file, then click Next.
b.
Locate the BIOS file from the Open window, then click Open.
3.
Follow the onscreen instructions to complete the updating process.
2.1.2
ASUS EZ Flash 2
The ASUS EZ Flash 2 feature allows you to update the BIOS without using an OS‑based
utility.
Before you start using this utility, download the latest BIOS file from the ASUS website at
www.asus.com.
To update the BIOS using EZ Flash 2:
1.
Insert the USB flash disk that contains the latest BIOS file to the USB port.
2.
Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash Utility and press <Enter> to enable it.
Exit
ASUSTek EZ Flash 2 BIOS ROM Utility V00.74
Flash Info
MODEL: P8H67-V
VER: 0211
DATE: 09/20/2010
File Path: fs0:\
Drive
fs0:\
Folder Info
09/27/10
10:23p
4194304
P8H67V.ROM
File Info
MODEL:
VER:
DATE
Help Info
[Enter] Select or Load
2-2
[Tab] Switch
[Up/Down/PageUp/PageDown/Home/End] Move
[Esc] Exit
ASUS P8H67-V
3.
Press <Tab> to switch to the Drive field.
4.
Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS,
and then press <Enter>.
5.
Press <Tab> to switch to the Folder Info field.
6.
Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform
the BIOS update process. Reboot the system when the update process is done.
• This function supports USB flash disks with FAT 32/16 format and single partition only.
• DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
2.1.3
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file
when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS
file using the motherboard support DVD or a USB flash drive that contains the updated BIOS
file.
The BIOS file in the support DVD may not be the latest version. Download the latest BIOS
file from the ASUS website at www.asus.com.
Recovering the BIOS
To recover the BIOS:
1.
Turn on the system.
2.
Insert the support DVD to the optical drive or the USB flash drive that contains the
BIOS file to the USB port.
3.
The utility automatically checks the devices for the BIOS file. When found, the utility
reads the BIOS file and enters ASUS EZ Flash 2 utility automatically.
4.
The system requires you to enter BIOS Setup to recover BIOS setting. To ensure
system compatibility and stability, we recommend that you press <F5> to load default
BIOS values.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause
system boot failure!
Chapter 2: BIOS information
2-3
2.1.4
ASUS BIOS Updater
The ASUS BIOS Updater allows you to update BIOS in DOS environment. This utility also
allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or
gets corrupted during the updating process.
The succeeding utility screens are for reference only. The actual utility screen displays may
not be same as shown.
Before updating BIOS
1.
Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and
single partition.
2.
Download the latest BIOS file and BIOS Updater from the ASUS website at
http://support.asus.com and save them on the USB flash drive.
NTFS is not supported under DOS environment. Do not save the BIOS file and BIOS
Updater to a hard disk drive or USB flash drive in NTFS format.
3.
Turn off the computer and disconnect all SATA hard disk drives (optional).
Booting the system in DOS environment
1.
Insert the USB flash drive with the latest BIOS file and BIOS Updater to the USB port.
2.
Boot your computer. When the ASUS Logo appears, press <F8> to show the BIOS
Boot Device Select Menu. Insert the support DVD into the optical drive and select the
optical drive as the boot device.
Please select boot device:
SATA: XXXXXXXXXXXXXXXX
USB XXXXXXXXXXXXXXXXX
UEFI: XXXXXXXXXXXXXXXX
Enter Setup
↑ and ↓ to move selection
ENTER to select boot device
ESC to boot using defaults
3. When the Make Disk menu appears, select the FreeDOS command prompt item by
pressing the item number.
4.
At the FreeDOS prompt, type d: and press <Enter> to switch the disk from
Drive C (optical drive) to Drive D (USB flash drive).
Welcome to FreeDOS (http://www.freedos.org)!
C:\>d:
D:\>
2-4
ASUS P8H67-V
Backing up the current BIOS
To backup the current BIOS file using the BIOS Updater
Ensure that the USB flash drive is not write-protected and has at least 1024KB free space
to save the file.
1.
At the FreeDOS prompt, type bupdater /o[filename] and press <Enter>.
D:\>bupdater /oOLDBIOS1.rom
Filename Extension
The [filename] is any user-assigned filename with no more than eight alphanumeric
characters for the filename and three alphanumeric characters for the extension.
2.
The BIOS Updater backup screen appears indicating the BIOS backup process. When
BIOS backup is done, press any key to return to the DOS prompt.
ASUSTek BIOS Updater for DOS V1.07
Current ROM
BOARD: P8H67-V
VER: 0217
DATE: 09/25/2010
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
PATH: A:\
BIOS backup is done! Press any key to continue.
Note
Saving BIOS:
Chapter 2: BIOS information
2-5
Updating the BIOS file
To update the BIOS file using BIOS Updater
1.
At the FreeDOS prompt, type bupdater /pc /g and press <Enter>.
D:\>bupdater /pc /g
2.
The BIOS Updater screen appears as below.
ASUSTek BIOS Updater for DOS V1.07
Current ROM
BOARD: P8H67-V
VER: 0217
DATE: 09/25/2010
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
PATH: A:\
P8H67V.ROM
A:
4194304 2010-09-20 17:30:48
Note
[Enter] Select or Load
[Up/Down/Home/End] Move
3.
[Tab] Switch
[B] Backup
[V] Drive Info
[Esc] Exit
Press <Tab> to switch between screen fields and use the <Up/Down/Home/End> keys
to select the BIOS file and press <Enter>. BIOS Updater checks the selected BIOS file
and prompts you to confirm BIOS update.
Are you sure to update BIOS?
Yes
4.
No
Select Yes and press <Enter>. When BIOS update is done, press <ESC> to exit BIOS
Updater. Restart your computer.
DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
• For BIOS Updater version 1.04 or later, the utility automatically exits to the DOS prompt
after updating BIOS.
• Ensure to load the BIOS default settings to ensure system compatibility and stability.
Select the Load Optimized Defaults item under the Exit menu. Refer to section 2.9
Exit menu for details.
• Ensure to connect all SATA hard disk drives after updating the BIOS file if you have
disconnected them.
2-6
ASUS P8H67-V
2.2
BIOS setup program
Use the BIOS Setup program to update the BIOS or configure its parameters. The BIOS
screens include navigation keys and brief online help to guide you in using the BIOS Setup
program.
Entering BIOS Setup at startup
To enter BIOS Setup at startup:
• Press <Delete> during the Power-On Self Test (POST). If you do not press <Delete>,
POST continues with its routines.
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
• Press <Ctrl>+<Alt>+<Del> simultaneously.
•
Press the reset button on the system chassis.
•
Press the power button to turn the system off then back on. Do this option only if you
failed to enter BIOS Setup using the first two options.
Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force reset from
a running operating system can cause damage to your data or system. We recommend to
always shut down the system properly from the operating system.
• The BIOS setup screens shown in this section are for reference purposes only, and may
not exactly match what you see on your screen.
• Ensure that a USB mouse is connected to your motherboard if you want to use the
mouse to control the BIOS setup program.
• The default BIOS settings for this motherboard apply for most conditions to ensure
optimum performance. If the system becomes unstable after changing any BIOS
settings, load the default settings to ensure system compatibility and stability. Select the
Load Optimized Defaults item under the Exit Menu. See section 2.9 Exit Menu.
• If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. Refer to section 1.9 Jumpers on how to
erase the RTC RAM.
• The BIOS setup program does not support the bluetooth devices.
Chapter 2: BIOS information
2-7
BIOS menu screen
The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode.
You can change modes from the Exit menu or from the Exit/Advanced Mode button in the EZ
Mode/Advanced Mode screen.
EZ Mode
By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ
Mode provides you an overview of the basic system information, and allows you to select
the display language, system performance mode and boot device priority. To access the
Advanced Mode, click Exit/Advanced Mode, then select Advanced Mode.
The default screen for entering the BIOS setup program can be changed. Refer to the
Setup Mode item in section 2.7 Boot memu for details.
Exits the BIOS setup program without saving
the changes, saves the changes and resets
the system, or enters the Advanced Mode
Displays the CPU/motherboard
temperature, CPU/5V/3.3V/12V voltage
output, CPU/chassis/power fan speed
Selects the display language of
the BIOS setup program
EFI BIOS Utility - EZ Mode
Exit/Advanced Mode
P8H67-V
Monday [9/27/2010]
English
BIOS Version : 0217
Build Date : 09/25/2010
CPU Type : Genuine Intel(R) CPU 0 @ 3.10GHz
Speed : 3100 MHz
Total Memory : 1024 MB (DDR3 1333MHz)
Temperature
Voltage
CPU
+113.0ºF/+45.0ºC
CPU
1.248V
5V
MB
+75.2ºF/+40.0ºC
3.3V
3.344V
12V
5.160V
12.248V
Fan Speed
CPU_FAN
4485RPM
CHA_FAN1
N/A
PWR_FAN
N/A
CHA_FAN2
N/A
System Performance
Quiet
Performance
Energy Saving
Normal
Boot Priority
Use the mouse to drag or keyboard to navigate to decide the boot priority.
Boot Menu(F8)
Selects the boot device priority
Loads optimized default
Power Saving mode
Displays the system properties of the
selected mode on the right hand side
Default(F5)
Normal mode
ASUS Optimal mode
Selects the boot device priority
• The boot device options vary depending on the devices you installed to the system.
• The Boot Menu(F8) button is available only when the boot device is installed to the
system.
2-8
ASUS P8H67-V
Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to configure
the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the
following sections for the detailed configurations.
To access the EZ Mode, click Exit, then select ASUS EZ Mode.
Back button
Menu bar Pop-up window
General help
EFI BIOS Utility - Advanced Mode
Ai Tweaker
Main
Back
Exit
Advanced
Monitor
Boot
Tool
Advanced\ CPU Configuration >
Enabled/Disabled JMB Storage Controller.
CPU Configuration
Genuine Intel(R) CPU 0 @ 3.10GHz
EM64T
Processor Speed
Preocessor Stepping
Microcode Revision
Processor Cores
Intel HT Technology
CPU Ratio Range
CPU Current Ratio
CPU Ratio
Supported
3100 MHz
206a5
4
4
Supported
16-31
31 Monitor
Intel Adaptive Thermal
Intel Adaptive Thermal Monitor
Disabled
Enabled
Auto
Enabled
Hyper-threading
Enabled
Active Processor Cores
All
Limit CPUID Maximum
Disabled
Execute Disable Bit
Enabled
Intel Virtualization Technology
Disabled
Enhanced Intel SpeedStep Technology
Enalbed
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Version 2.00.1201. Copyright (C) 2010 American Megatrends, Inc.
Configuration fields
Menu items
Scroll bar
Navigation keys
Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration
Ai Tweaker
For changing the overclocking settings
Advanced
For changing the advanced system settings
Monitor
For displaying the system temperature, power status, and changing the fan settings
Boot
For changing the system boot configuration
Tool
For configuring options for special functions
Exit
For selecting the exit options and loading default settings
Chapter 2: BIOS information
2-9
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example,
selecting Main shows the Main menu items.
The other items (Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have
their respective menu items.
Back button
This button appears when entering a submenu. Press <Esc> or use the USB mouse to click
this button to return to the previous menu screen.
Submenu items
A greater than sign (>) before each item on any menu screen means that the item has a
submenu. To display the submenu, select the item and press <Enter> or double-click the
item.
Pop-up window
Select a menu item and press <Enter> to display a pop-up window with the configuration
options for that item.
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit on
the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display the
other items on the screen.
Navigation keys
At the bottom right corner of the menu screen are the navigation keys for the BIOS setup
program. Use the navigation keys to select items in the menu and change the settings.
General help
At the top right corner of the menu screen is a brief description of the selected item.
Configuration fields
These fields show the values for the menu items. If an item is user-configurable, you can
change the value of the field opposite the item. You cannot select an item that is not
user-configurable.
A configurable field is highlighted when selected. To change the value of a field, select it and
press <Enter> or click on it to display a list of options.
2-10
ASUS P8H67-V
2.3
Main menu
The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup
program. The Main menu provides you an overview of the basic system information, and
allows you to set the system date, time, language, and security settings.
EFI BIOS Utility - Advanced Mode
Main
Ai Tweaker
Exit
Advanced
Monitor
BIOS Information
BIOS Version
Build Date
ME Version
0217 x64
09/25/2010
7.0.0.1095
CPU Information
Genuine Intel(R) CPU 0 @ 3.10GHz
Speed
3100 MHz
Memory Information
Total Memory
Speed
1024 MB
1333 MHz
System Language
System Date
System Time
Access Level
Boot
Tool
Choose the system default language
English
[Mon 09/27/2010]
[16:46:15]
Administrator
> Security
2.3.1
System Language [English]
2.3.2
System Date [Day xx/xx/xxxx]
2.3.3
System Time [xx:xx:xx]
2.3.4
Security
Allows you to choose the BIOS language version from the options. Configuration options:
[English]
Allows you to set the system date.
Allows you to set the system time.
The Security menu items allow you to change the system security settings.
• If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC)
RAM to clear the BIOS password. See section 1.9 Jumpers for information on how to
erase the RTC RAM.
• The Administrator or User Password items on top of the screen show the default Not
Installed. After you set a password, these items show Installed.
Chapter 2: BIOS information
2-11
Administrator Password
If you have set an administrator password, we recommend that you enter the administrator
password for accessing the system. Otherwise, you might be able to see or change only
selected fields in the BIOS setup program.
To set an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Create New Password box, key in a password, then press <Enter>.
3.
Confirm the password when prompted.
To change an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then press
<Enter>.
3.
From the Create New Password box, key in a new password, then press <Enter>.
4.
Confirm the password when prompted.
To clear the administrator password, follow the same steps as in changing an administrator
password, but press <Enter> when prompted to create/confirm the password. After you clear
the password, the Administrator Password item on top of the screen shows Not Installed.
User Password
If you have set a user password, you must enter the user password for accessing the system.
The User Password item on top of the screen shows the default Not Installed. After you set
a password, this item shows Installed.
To set a user password:
1.
Select the User Password item and press <Enter>.
2.
From the Create New Password box, key in a password, then press <Enter>.
3.
Confirm the password when prompted.
To change a user password:
1.
Select the User Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then press
<Enter>.
3.
From the Create New Password box, key in a new password, then press <Enter>.
4.
Confirm the password when prompted.
To clear the user password, follow the same steps as in changing a user password, but press
<Enter> when prompted to create/confirm the password. After you clear the password, the
User Password item on top of the screen shows Not Installed.
2-12
ASUS P8H67-V
2.4
Ai Tweaker menu
The Ai Tweaker menu items allow you to configure overclocking-related items.
Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field
values can cause the system to malfunction.
The configuration options for this section vary depending on the CPU and DIMM model you
installed on the motherboard.
EFI BIOS Utility - Advanced Mode
Ai Tweaker
Main
Exit
Advanced
Monitor
Ai Overclock Tuner
Auto
Memory Frequency
Boot
Tool
[X.M.P.] When XMP is enabled BCLK
frequency, CPU ratio and memory
parameters will be auto optimized.
Auto
EPU Power Saving Mode
Disabled
> OC Tuner
> DRAM Timing Control
> CPU Power Management
CPU Offset Mode Sign
+
CPU Voltage
Auto
DRAM Voltage
1.500V
1.55000
VCCIO Voltage
1.050V
Auto
CPU PLL Voltage
1.800v
Auto
PCH Voltage
1.050V
Auto
Load-Line Calibration
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Auto
Version 2.00.1201. Copyright (C) 2010 American Megatrends, Inc.
2.4.1
Ai Overclock Tuner [Auto]
Allows you to select the CPU overclocking options to achieve the desired CPU internal
frequency. Select any of these preset overclocking configuration options:
[Auto]Loads the optimal settings for the system.
[Manual]
Allows you to individually set overclocking parameters.
BCLK/PEG Frequency [XXX]
Allows you to adjust the CPU and VGA frequency to enhance the system performance. Use
the <+> and <-> keys to adjust the value. You can also key in the desired value using the
numeric keypad. The values range from 80.0MHz to 300.0MHz.
Chapter 2: BIOS information
2-13
2.4.2
Memory Frequency [Auto]
Allows you to set the memory operating frequency. Configuration options: [DDR3-800MHz]
[DDR3-1066MHz] [DDR3-1333MHz]
Selecting a very high memory frequency may cause the system to become unstable! If this
happens, revert to the default setting.
2.4.3
EPU Power Saving MODE [Disabled]
2.4.4
GPU Boost
2.4.5
DRAM Timing Control
Allows you to enable or disable the EPU power saving function.
Configuration options: [Disabled] [Enabled]
GPU Boost accelerates the integrated GPU for extreme graphics performance.
Configuration options: [OK] [Cancel]
The sub-items in this menu allow you to set the DRAM timing control features. Use the <+>
and <-> keys to adjust the value. To restore the default setting, type [auto] using the keyboard
and press <Enter>.
Changing the values in this menu may cause the system to become unstable! If this
happens, revert to the default settings.
2.4.6
CPU Power Management
The sub-items in this menu allow you to set the CPU ratio and features.
CPU Ratio [Auto]
Allows you to manually adjust the maximum non-turbo CPU ratio. Use <+> and <->
keys or the numeric keypad to adjust the value. The valid value ranges vary according
to your CPU model.
Enhanced Intel SpeedStep Technology [Enabled]
Allows you to enable or disable the Enhanced Intel® SpeedStep Technology (EIST).
[Disabled]
Disables this function.
[Enabled]The operating system dynamically adjusts the processor voltage and
core frequency which may result in decreased average consumption
and decreased average heat production.
Turbo Mode [Enabled]
This item appears only when you set the Enhanced Intel SpeedStep Technology
item to [Enabled].
[Enabled]Allows processor cores to run faster than marked frequency in specific
conditions.
[Disabled]
2-14
Disables this function.
ASUS P8H67-V
The following three items appear only when you set both the Enhanced Intel SpeedStep
Technology and Turbo Mode items to [Enabled].
Long duration power limit [Auto]
Use <+>/<-> to adjust the value.
Long duration maintained [Auto]
Use <+>/<-> to adjust the value.
Short duration power limit [Auto]
Use <+>/<-> to adjust the value.
Power Limit Control [Disabled]
Allows you to enable or disable the power limit control function.
Configuration options: [Disabled] [Enabled]
The following two items appear only when you set the Power Limit Control item to
[Enabled].
Power Limit [Auto]
Use <+>/<-> to adjust the value.
Power Limit Time [10]
Use <+>/<-> to adjust the value.
Primary Plane Current Limit [Auto]
Use <+>/<-> to adjust the value.
Secondary Plane Current Limit [Auto]
Use <+>/<-> to adjust the value.
Some of the following items are adjusted by typing the desired values using the numeric
keypad and press <Enter>. You can also use the <+> and <-> keys to adjust the value. To
restore the default setting, type [auto] using the keyboard and press <Enter>.
2.4.7
[+]
[–]
CPU Offset Mode Sign [+]
To offset the voltage by a positive value.
To offset the voltage by a negative value.
CPU Voltage [Auto]
Allows you to set the Offset voltage. The values range from -0.635V to +0.635V with a
0.005V interval.
Refer to the CPU documentation before setting the CPU voltage. Setting a high voltage
may damage the CPU permanently, and setting a low voltage may make the system
unstable.
Chapter 2: BIOS information
2-15
2.4.8
DRAM Voltage [Auto]
Allows you to set the DRAM voltage. The values range from 1.185V to 2.135V with a 0.005V
interval.
According to Intel CPU specification, DIMMs with voltage requirement over 1.65V may
damage the CPU permanently. We recommend you install the DIMMs with the voltage
requirement below 1.65V.
2.4.9
VCCIO Voltage [Auto]
2.4.10
CPU PLL Voltage [Auto]
2.4.11
PCH Voltage [Auto]
Allows you to set the VCCIO voltage. The values range from 0.7350V to 1.6850V with a
0.005V interval.
Allows you to set the CPU PLL voltage. The values range from 1.8000V to 1.9000V with a
0.1V interval
Allows you to set the Platform Controller Hub voltage. The values range from 0.735V to
1.685V with a 0.005V interval.
• The values of the CPU Offset Voltage, DRAM Voltage, VCCIO Voltage, CPU PLL
Voltage, and PCH Voltage items are labeled in different color, indicating the risk levels
of high voltage settings.
• The system may need better cooling system to work stably under high voltage settings.
2.4.12
Load-Line Calibration [Auto]
Load-line is defined by Intel VRM specification and affects CPU voltage. The CPU working
voltage will decrease proportionally to CPU loading. Higher load-line calibration would get
higher voltage and better overclocking performance, but increase the CPU and VRM thermal.
This item allows you to set this function for better system performance. Configuration options:
[Auto] [Disabled] [Enabled]
The actual performance boost may vary depending on your CPU specification.
2.4.13
CPU Spread Spectrum [Auto]
[Auto]Automatic configuration.
[Disabled]
Enhances the BCLK overclocking ability.
[Enabled]
Sets to [Enabled] for EMI control.
2-16
ASUS P8H67-V
2.5
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect field values
can cause the system to malfunction.
EFI BIOS Utility - Advanced Mode
Ai Tweaker
Main
Advanced
Exit
Monitor
Boot
Tool
Trusted Computing (TPM) settings
> CPU Configuration
> System Agent Configuration
> PCH Configuration
> SATA Configuration
> USB Configuration
> Onboard Devices Configuration
> APM
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Version 2.00.1201. Copyright (C) 2010 American Megatrends, Inc.
2.5.1
CPU Configuration
The items in this menu show the CPU-related information that the BIOS automatically
detects.
The items shown in submenu may be different due to the CPU you installed.
CPU Ratio [Auto]
Allows you to set the ratio between the CPU Core Clock and the BCLK Frequency. Use <+>
and <-> keys or the numeric keypad to adjust the ratio. The valid value ranges vary according
to your CPU model.
Intel Adaptive Thermal Monitor [Enabled]
[Enabled]
[Disabled]
Enables the overheated CPU to throttle its clock speed to cool down.
Disables the CPU thermal monitor function.
Chapter 2: BIOS information
2-17
Hyper-threading [Enabled]
The Intel Hyper-Threading Technology allows a hyper-threading processor to appear as two
logical processors to the operating system, allowing the operating system to schedule two
threads or processes simultaneously.
[Enabled]
Two threads per activated core are enabled.
[Disabled]
Only one thread per activated core is enabled.
Active Processor Cores [All]
Allows you to choose the number of CPU cores to activate in each processor package.
Configuration options: [All] [1] [2] [3]
Limit CPUID Maximum [Disabled]
[Enabled]Allows legacy operating systems to boot even without support for CPUs
with extended CPUID functions.
[Disabled]
Disables this function.
Execute Disable Bit [Enabled]
[Enabled]
[Disabled]
Enables the No-Execution Page Protection Technology.
Forces the XD feature flag to always return to zero (0).
Intel(R) Virtualization Tech [Disabled]
[Enabled]Allows a hardware platform to run multiple operating systems separately
and simultaneously, enabling one system to virtually function as several
systems.
[Disabled]
Disables this function.
Enhanced Intel SpeedStep Technology [Enabled]
Allows you to enable or disable the Enhanced Intel® SpeedStep Technology (EIST).
[Disabled]
The CPU runs at its default speed.
[Enabled]
The operating system controls the CPU speed.
Turbo Mode [Enabled]
This item appears only when you set the EIST item to [Enabled] and allows you to enable or
disable the Intel® Turbo Mode Technology.
[Enabled]
Allows processor cores to run faster than marked frequency in specific
condition.
[Disabled]
Disables this function.
CPU C1E [Enabled]
[Enabled]Enables the C1E support function. This item should be enabled in order to
enable the Enhanced Halt State.
[Disabled]
Disables this function.
2-18
ASUS P8H67-V
CPU C3 Report [Disabled]
Allows you to disable or enable the CPU C3 report to OS.
Configuration options: [Disabled] [ACPI C-2] [ACPI C-3]
CPU C6 Report [Enabled]
Allows you to disable or enable the CPU C6 report to OS.
Configuration options: [Enabled] [Disabled]
Package C State limit [No Limit]
We recommend that you set this item to [No Limit] for BIOS to automatically detect the
C-State mode supported by your CPU. Configuration options: [No Limit] [C0] [C1] [C6] [C7]
2.5.2
System Agent Configuration
VT-d [Disabled]
[Disabled] Disables the Intel Virtualization Technology for Directed I/O.
[Enabled] Enables the Intel Virtualization Technology for Directed I/O.
Initiate Graphic Adapter [PEG/PCI]
Allows you to decide which graphics controller to use as the primary boot device.
Configuration options: [PCI/PEG] [PEG/PCI]
IGD Memory [64M]
Allows you to set the Internal Graphics Device share memory size.
Configuration options: [32M] [64M] [96M] [128M]
Render Standby [Enabled]
Allows you to enable or disable Render Standby by Internal Graphics Device.
Configuration options: [Disabled] [Enabled]
IGD Multi-Monitor [Disabled]
Allows you enable or disable Internal Graphics Device Multi-Monitor Support for add-on VGA
devices. Configuration options: [Enabled] [Disabled]
2.5.3
PCH Configuration
High Precision Timer [Enabled]
Allows you to enable or disable the High Precision Event Timer.
Configuration options: [Enabled] [Disabled]
Chapter 2: BIOS information
2-19
2.5.4
SATA Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show Not Present if no SATA device is installed to the corresponding SATA
port.
SATA Mode [IDE Mode]
Allows you to set the SATA configuration.
[Disabled]Disables the SATA function.
[IDE Mode]Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as
Parallel ATA physical storage devices.
[AHCI Mode]Set to [AHCI Mode] when you want the SATA hard disk drives to use the
AHCI (Advanced Host Controller Interface). The AHCI allows the onboard
storage driver to enable advanced Serial ATA features that increases
storage performance on random workloads by allowing the drive to
internally optimize the order of commands.
[RAID Mode]Set to [RAID Mode] when you want to create a RAID configuration from the
SATA hard disk drives.
Serial-ATA Controller 0 [Enhanced]
This item appears only when you set the SATA Mode item to [IDE Mode].
[Disabled]
Disables the SATA function.
[Enhanced]
Set to [Enhanced] to support more than four SATA devices.
[Compatible]Set to [Compatible] when using Windows 98/NT/2000/MS-DOS. Up to four
SATA devices are supported under these oeprating syste.
Serial-ATA Controller 1 [Enhanced]
This item appears only when you set the SATA Mode item to [IDE Mode].
[Disabled]
Disables the SATA function.
[Enhanced]
Set to [Enhanced] to support more than four SATA devices.
S.M.A.R.T. Status Check [Enabled]
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When
read/write of your hard disk errors occur, this feature allows the hard disk to report warning
messages during the POST. Configuration options: [Enabled] [Disabled]
2-20
ASUS P8H67-V
2.5.5
USB Configuration
The items in this menu allow you to change the USB-related features.
The USB Devices item shows the auto-detected values. If no USB device is detected, the
item shows None.
Legacy USB Support [Enabled]
[Enabled]
[Disabled]
[Auto] Enables the support for USB 3.0 devices on legacy operating systems
(OS).
The USB devices can be used only for the BIOS setup program.
Allows the system to detect the presence of USB devices at startup. If
detected, the USB controller legacy mode is enabled. If no USB device is
detected, the legacy USB support is disabled.
Legacy US3.0 Support [Enabled]
[Enabled]
[Disabled]
Enables the support for USB 3.0 devices on legacy operating systems
(OS).
Disables the function.
EHCI Hand-off [Disabled]
[Enabled]
[Disabled]
2.5.6
Enables the support for operating systems without an EHCI hand‑off
feature.
Disables the function.
Onboard Devices Configuration
Azalia HD Audio [Enabled]
[Enabled]
[Disabled]
Enables the High Definition Audio Controller.
Disables the controller.
The following two items appear only when you set the Azalia HD Audio item to [Enabled].
Front Panel Type [HD]
Allows you to set the front panel audio connector (AAFP) mode to legacy AC’97 or highdefinition audio depending on the audio standard that the front panel audio module supports.
[HD]
Sets the front panel audio connector (AAFP) mode to high definition audio.
[AC97]
Sets the front panel audio connector (AAFP) mode to legacy AC’97
SPDIF Out Type [SPDIF]
Allows you to select the digital audio output type. Configuartion options: [SPIDF] [HDMI]
VIA Storage Controller [Enabled]
[Enabled] Enables the onboard storage controller.
[Disabled] Disables the controller.
Chapter 2: BIOS information
2-21
VIA Storage OPROM [Enabled]
This item appears only when the VIA Storage Controller item is set to [Enalbed] and allows
you to enable or disable the OptionROM of the VIA Storage controller.
Configuration options: [Enabled] [Disabled]
PCI Express x16_2 slot (black) bandwidth [Auto]
[Auto]
[X4 Mode]
[x2 mode]
The PCIe X16_2 slot runs at x4/x2 mode for system resource optimization.
The PCIe X16_2 slot runs at x4 mode for high performance support.
(PCIe X1_1, and PCIe X1_2 slots will be disabled.)
The PCIe X16_2 slot runs at x2 mode with all slots enabled.
The PCIe x1 slots share the bandwidth with the PCIe x16_2 slot. Due to the CrossFireX™
limitation, DO NOT use the PCIe x1 slots when you install two CrossFireX™ graphics cards
on both the PCIe x16 slots to set up a CrossFireX™ configuration.
Atheros LAN [Enabled]
[Enabled] Enables the Atheros LAN controller.
[Disabled] Disables the controller.
Atheros ROM [Disabled]
This item appears only when you set the Atheros LAN item to [Enabled] and allows you to
enable or disable the Rom Help of the Atheros LAN controller.
Configuration options: [Enabled] [Disabled]
Asmedia USB 3.0 Controller [Enabled]
[Enabled] Enables the onboard USB 3.0 controller.
[Disabled] Disables the controller.
The following one item appear only when the Asmedia USB 3.0 Controller item is set to
[Enabled].
Asmedia USB 3.0 Battery Charging Support [Enabled]
[Enabled] Enables the Asmedia USB 3.0 battery charging function.
[Disabled] Disables this function
Serial Port Configuration
The sub-items in this menu allow you to set the serial port configuration.
Serial Port [Enabled]
Allows you to enable or disable the serial port (COM).
Configuration options: [Enabled] [Disabled]
Change Settings [IO=3F8h; IRQ=4]
Allows you to select the Serial Port base address. Configuration options: [IO=3F8h;
IRQ=4] [IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3]
2-22
ASUS P8H67-V
2.5.7
APM
Restore AC Power Loss [Power Off]
[Power On]
[Power Off]
[Last State]
The system goes into on state after an AC power loss.
The system goes into off state after an AC power loss.
The system goes into either off or on state, whatever the system state was
before the AC power loss.
Power On By PS/2 Keyboard [Disabled]
[Disabled]
[Space Bar]
[Ctrl-Esc]
[Power Key]
Disables the Power On by a PS/2 keyboard.
Sets the Space Bar on the PS/2 keyboard to turn on the system.
Sets the Ctrl+Esc key on the PS/2 keyboard to turn on the system.
Sets Power key on the PS/2 keyboard to turn on the system. This feature
requires an ATX power supply that provides at least 1A on the +5VSB lead.
Power On By PS/2 Mouse [Disabled]
[Disabled]
[Enabled]
Disables the Power On by a PS/2 mouse.
Enables the Power On by a PS/2 mouse. This feature requires an ATX
power supply that provides at least 1A on the +5VSB lead.
Power On By PCI [Disabled]
[Disabled]
[Enabled]
Disables the PME to wake up from S5 by PCI devices.
Allows you to turn on the system through a PCI LAN or modem card. This
feature requires an ATX power supply that provides at least 1A on the
+5VSB lead.
Power On By PCIE [Disabled]
[Disabled]Disables the PCIE devices to generate a wake event.
[Enabled]Enables the PCIE devices to generate a wake event.
Power On By Ring [Disabled]
[Disabled]
[Enabled]
Disables Ring to generate a wake event.
Enables Ring to generate a wake event.
Power On By RTC [Disabled]
[Disabled]
[Enabled]
Disables RTC to generate a wake event.
When set to [Enabled], the items RTC Alarm Date (Days) and Hour/
Minute/Second will become user-configurable with set values.
Chapter 2: BIOS information
2-23
2.6
Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
EFI BIOS Utility - Advanced Mode
Main
Ai Tweaker
Exit
Advanced
Monitor
CPU Temperature
+45ºC / +113ºF
MB Temperature
+34ºC / +93ºF
CPU Fan Speed
Boot
Tool
CPU Temperature
4515 RPM
Chassis Fan 1 Speed
N/A
Chassis Fan 2 Speed
N/A
Power Fan Speed
N/A
CPU Q-Fan Control
Enabled
CPU Fan Speed Low Limit
600 RPM
CPU Fan Profile
Standard
Chassis Q-Fan Control
Enabled
Chassis Fan Speed Low Limit
600 RPM
Chassis Fan Profile
Standard
CPU Voltage
+1.184 V
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Version 2.00.1201. Copyright (C) 2010 American Megatrends, Inc.
Scroll down to display the following items:
3.3V Voltage
+3.312 V
5V Voltage
+5.080 V
12V Voltage
+12.192 V
Anti Surge Support
Enabled
Version 2.00.1201. Copyright (C) 2010 American Megatrends, Inc.
2.6.1
CPU Temperature / MB Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the CPU and motherboard
temperatures. Select Ignore if you do not wish to display the detected temperatures.
2.6.2CPU / Chassis / Power Fan Speed [xxxx RPM] or [Ignore] /
[N/A]
The onboard hardware monitor automatically detects and displays the CPU, chassis,
and power fan speeds in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A. Select Ignore if you do not wish to display the detected
speed.
2-24
ASUS P8H67-V
2.6.3
[Disabled]
[Enabled]
CPU Q-Fan Control [Enabled]
Disables the CPU Q-Fan control feature.
Enables the CPU Q-Fan control feature.
CPU Fan Speed Low Limit [600 RPM]
This item appears only when you enable the CPU Q-Fan Control feature and allows
you to disable or set the CPU fan warning speed.
Configuration options: [Ignore] [300 RPM] [400 RPM] [500 RPM] [600 RPM]
CPU Fan Profile [Standard]
This item appears only when you enable the CPU Q-Fan Control feature and allows
you to set the appropriate performance level of the CPU fan.
[Standard]Sets to [Standard] to make the CPU fan automatically adjust depending on
the CPU temperature.
[Silent]Sets to [Silent] to minimize the fan speed for quiet CPU fan operation.
[Turbo]
Sets to [Turbo] to achieve maximum CPU fan speed.
[Manual] Sets to [Manual] to assign detailed fan speed control parameters.
The following four items appear only when you set CPU Fan Profile to [Manual].
CPU Upper Temperature [70ºC]
Use the <+> and <-> keys to adjust the upper limit of the CPU temperature. The values range
from 40ºC to 90ºC.
CPU Fan Max. Duty Cycle(%) [100%]
Use the <+> and <-> keys to adjust the maximum CPU fan duty cycle. The values range from
20% to 100%. When the CPU temperature reaches the upper limit, the CPU fan will operate at
the maximum duty cycle.
CPU Lower Temperature [40ºC]
Displays the lower limit of the CPU temperature.
CPU Fan Min. Duty Cycle(%) [20%]
Use the <+> and <-> keys to adjust the minimum CPU fan duty cycle. The values range from 0%
to 100%. When the CPU temperature is under 40ºC, the CPU fan will operate at the minimum
duty cycle.
2.6.4
[Disabled]
[Enabled]
Chassis Q-Fan Control [Enabled]
Disables the Chassis Q-Fan control feature.
Enables the Chassis Q-Fan control feature.
Chassis Fan Speed Low Limit [600 RPM]
This item appears only when you enable the Chassis Q-Fan Control feature and
allows you to disable or set the chassis fan warning speed.
Configuration options: [Ignore] [300 RPM] [400 RPM] [500 RPM] [600 RPM]
Chapter 2: BIOS information
2-25
Chassis Fan Profile [Standard]
This item appears only when you enable the Chassis Q-Fan Control feature and
allows you to set the appropriate performance level of the chassis fan.
[Standard]Sets to [Standard] to make the chassis fan automatically adjust depending
on the chassis temperature.
[Silent]Sets to [Silent] to minimize the fan speed for quiet chassis fan operation.
[Turbo]
Sets to [Turbo] to achieve maximum chassis fan speed.
[Manual] Sets to [Manual] to assign detailed fan speed control parameters.
The following four items appear only when you set Chassis Fan Profile to [Manual].
Chassis Upper Temperature [70ºC]
Use the <+> and <-> keys to adjust the upper limit of the CPU temperature. The values range
from 40ºC to 90ºC.
Chassis Fan Max. Duty Cycle(%) [100%]
Use the <+> and <-> keys to adjust the maximum chassis fan duty cycle. The values range
from 20% to 100%. When the chassis temperature reaches the upper limit, the chassis fan will
operate at the maximum duty cycle.
Chassis Lower Temperature [40ºC]
Displays the lower limit of the chassis temperature.
CPU Fan Min. Duty Cycle(%) [60%]
Use the <+> and <-> keys to adjust the minimum chassis fan duty cycle. The values range from
0% to 100%. When the chassis temperature is under 40ºC, the chassis fan will operate at the
minimum duty cycle.
2.6.5
CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
2.6.6
Anti Surge Support [Enabled]
The onboard hardware monitor automatically detects the voltage output through the onboard
voltage regulators. Select Ignore if you do not want to detect this item.
This item allows you to enable or disable the Anti Surge function.
Configuration options: [Disabled] [Enabled]
2-26
ASUS P8H67-V
2.7
Boot menu
The Boot menu items allow you to change the system boot options.
EFI BIOS Utility - Advanced Mode
Ai Tweaker
Main
Exit
Advanced
Bootup NumLock State
Full Screen Logo
Option ROM Messages
Monitor
On
Boot
Tool
Select the keyboard NumLock state
Enabled
Force BIOS
Setup Mode
EZ Mode
Boot Option Priorities
Boot Option #1
SATA: xxxxxxx
Boot Option #2
SATA: xxxxxxx
Boot Override
> SATA: xxxxxxxxxxxx
> SATA: xxxxxxxxxxxx
> Hard Drive BBS Priorities
> CD/DVD ROM Drive BBS Priorities
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Version 2.00.1201. Copyright (C) 2010 American Megatrends, Inc.
2.7.1
Bootup NumLock State [On]
2.7.2
Full Screen Logo [Enabled]
[On]
[Off]
[Enabled]
[Disabled]
Sets the power-on state of the NumLock to [On].
Sets the power-on state of the NumLock to [Off].
Enables the full screen logo display feature.
Disables the full screen logo display feature.
Set this item to [Enabled] to use the ASUS MyLogo 2™ feature.
Post Report [5 sec]
This item appears only when the Full Screen Logo item is set to [Disabled] and allows you to
set the waiting time for the system to display the post report. .
Configuration options: [1 sec] [2 sec] [3 sec] [4 sec] [5 sec] [6 sec] [7 sec] [8 sec]
[9 sec] [10 sec] [Until Press ESC]
Chapter 2: BIOS information
2-27
2.7.3
Option ROM Messages [Force BIOS]
2.7.4
Setup Mode [EZ Mode]
2.7.5
Boot Option Priorities
[Force BIOS]
The third-party ROM messages will be forced to display during the boot
sequence.
[Keep Current] The third-party ROM messages will be displayed only if the third-party
manufacturer had set the add-on device to do so.
[Advanced Mode] Sets Advanced Mode as the default screen for entering the BIOS setup
program.
[EZ Mode]
Sets EZ Mode as the default screen for entering the BIOS setup program.
These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
• To select the boot device during system startup, press <F8> when ASUS Logo appears.
• To access Windows OS in Safe Mode, do any of the following:
- Press <F5> when ASUS Logo appears.
- Press <F8> after POST.
2.7.6
Boot Override
These items displays the available devices. The number of device items that appears on
the screen depends on the number of devices installed in the system. Click an item to start
booting from the selected device.
2-28
ASUS P8H67-V
2.8
Tools menu
The Tools menu items allow you to configure options for special functions. Select an item
then press <Enter> to display the submenu.
EFI BIOS Utility - Advanced Mode
Ai Tweaker
Main
Advanced
Exit
Monitor
Boot
Tool
Be used to update BIOS
> ASUS EZ Flash Utility
> ASUS O.C. Profile
2.8.1
ASUS EZ Flash 2
Allows you to run ASUS EZ Flash 2. When you press <Enter>, a confirmation message
appears. Use the left/right arrow key to select between [Yes] or [No], then press <Enter> to
confirm your choice.
For more details, refer to section 2.1.2 ASUS EZ Flash 2.
2.8.2
ASUS O.C. Profile
This item allows you to store or load multiple BIOS settings.
The Setup Profile Status items show Not Installed if no profile is created.
Save to Profile
Allows you to save the current BIOS settings to the BIOS Flash, and create a profile. Key in a
profile number from one to eight, press <Enter>, and then select Yes.
Load from Profile
Allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile
number that saved your CMOS settings, press <Enter>, and then select Yes.
• DO NOT shut down or reset the system while updating the BIOS to prevent the system
boot failure!
• We recommend that you update the BIOS file only coming from the same memory/CPU
configuration and BIOS version.
Chapter 2: BIOS information
2-29
2.9
Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit
menu.
Exit
Load Optimized Defaults
Save Changes & Reset
Discard Changes & Exit
ASUS EZ Mode
Launch EFI Shell from filesystem device
Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press <F5>, a confirmation window appears.
Select Yes to load the default values.
Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press <F10>,
a confirmation window appears. Select Yes to save changes and exit.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you
select this option or if you press <Esc>, a confirmation window appears. Select Yes to
discard changes and exit.
ASUS EZ Mode
This option allows you to enter the EZ Mode screen.
Launch EFI Shell from filesystem device
This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of
the available filesystem devices.
2-30
ASUS P8H67-V
ASUS contact information
ASUSTeK COMPUTER INC.
Address
Telephone Fax E-mail
Web site
Technical Support
Telephone Online support
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
+886-2-2894-3447
+886-2-2890-7798
[email protected]
www.asus.com.tw
+86-21-38429911
support.asus.com
ASUS COMPUTER INTERNATIONAL (America)
Address
Telephone Fax
Web site
Technical Support
Telephone Support fax
Online support
800 Corporate Way, Fremont, CA 94539, USA
+1-510-739-3777
+1-510-608-4555
usa.asus.com
+1-812-282-2787
+1-812-284-0883
support.asus.com
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact
Technical Support
Telephone (Component)
Telephone (System/Notebook/Eee/LCD)
Support Fax
Online support
Harkort Str. 21-23, D-40880 Ratingen, Germany
+49-2102-959911
www.asus.de
www.asus.de/sales
+49-1805-010923*
+49-1805-010920*
+49-2102-9599-11
support.asus.com
* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile phone.
(510)739-3777/(510)608-4555
800 Corporate Way, Fremont, CA 94539.
Asus Computer International
Signature :
Date :
Representative Person’s Name :
Oct. 31, 2010
Steve Chang / President
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Supplementary Information:
FCC Part 15, Subpart E, Intentional Radiators
FCC Part 15, Subpart B, Unintentional Radiators
FCC Part 15, Subpart C, Intentional Radiators
Model Number : P8H67-V
Conforms to the following specifications:
Product Name : Motherboard
hereby declares that the product
Phone/Fax No:
Address:
Responsible Party Name:
Per FCC Part 2 Section 2. 1077(a)
DECLARATION OF CONFORMITY
Manufacturer:
HARKORT STR. 21-23, 40880 RATINGEN
GERMANY
Address, City:
Country:
EN 62301:2005
Declaration Date: Oct. 31, 2010
Year to begin affixing CE marking:2010
CE marking
EN 62301:2005
Regulation (EC) No. 642/2009
Signature : __________
Position : CEO
Name :
Jerry Shen
(EC conformity marking)
EN 62301:2005
Regulation (EC) No. 278/2009
EN 60950-1:2006+A11:2009
Regulation (EC) No. 1275/2008
2009/125/EC-ErP Directive
EN60065:2002+A1:2006
EN 60950-1:2006
EN 301 489-1 V1.8.1(2008-04)
EN 301 489-3 V1.4.1(2002-08)
EN 301 489-4 V1.3.1(2002-08)
EN 301 489-7 V1.3.1(2005-11)
EN 301 489-9 V1.4.1(2007-11)
EN 301 489-17 V1.3.2(2008-04)
EN 301 489-24 V1.4.1(2007-09)
EN 302 326-2 V1.2.2(2007-06)
EN 302 326-3 V1.3.1(2007-09)
EN 301 357-2 V1.3.1(2006-05)
EN 55024:1998+A1:2001+A2:2003
EN 61000-3-3:2008
EN 55020:2007
EN 60950-1:2001+A11:2004
2006/95/EC-LVD Directive
EN 300 328 V1.7.1(2006-05)
EN 300 440-1 V1.4.1(2008-05)
EN 300 440-2 V1.2.1(2008-03)
EN 301 511 V9.0.2(2003-03)
EN 301 908-1 V3.2.1(2007-05)
EN 301 908-2 V3.2.1(2007-05)
EN 301 893 V1.4.1(2005-03)
EN 50360:2001
EN 50371:2002
EN 62311:2008
EN 50385:2002
1999/5/EC-R &TTE Directive
EN 55022:2006+A1:2007
EN 61000-3-2:2006
EN 55013:2001+A1:2003+A2:2006
Motherboard
P8H67-V
Model name :
conform with the essential requirements of the following directives:
2004/108/EC-EMC Directive
Product name :
declare the following apparatus:
TAIWAN
ASUS COMPUTER GmbH
Authorized representative in Europe:
No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWAN R.O.C.
Country:
Address, City:
ASUSTek COMPUTER INC.
EC Declaration of Conformity
We, the undersigned,