Dynex DX-TVM112 Fixed TV Wall Mount For Most 26"-40" Flat-Panel TVs Quick Setup Guide
Add to my manualsThe Dynex DX-TVM112 is a low-profile TV mount designed to support TVs weighing up to 50 lbs (22.7 kg). It features a simple installation process with options for mounting on wood studs or solid concrete/concrete block walls. The mount is compatible with TVs with both flat and rounded back surfaces and includes various screws, spacers, and washers for a secure fit. It allows for easy cable management and provides a clean and modern look for your TV setup.
advertisement
Low-Profile TV Mount
QUICK SETUP GUIDE
DX-TVM112
Thank you for choosing the Dynex DX-TVM112. The DX-TVM112 TV mount is designed to support a TV weighing up to 50 lbs. (22.7 kg).
Package contents
A Wall plate (1)
B Left TV bracket (1)
C Right TV bracket (1)
M4 bag
D M4 x 12 mm screws (4)
E M4 x 30 mm screws (4)
F M4 spacers (4)
G M4 washers (8)
M6 bag
Tools you will need:
• 3/16 in. wood drill bit
• ½ in. masonry drill bit
• Level
• Socket wrench with ½ in. socket or
• Pencil
I M6 × 20 mm screws (4)
J M6 × 35 mm screws (4)
K M6 spacers (4)
L M6 washers (4)
Lag bolt bag
M Wall anchors (3)
N 5/16 in. (7.9 mm) washers (3)
• Awl
1 Attach the TV brackets
Option 1: Attaching to a TV with a flat back surface
Attach the left and right TV brackets (B and C) to the back of the TV using:
The M4 washers (G) and the M4 screws (D).
Or
The M6 washers (L) and the M6 screws (H or I).
NOTE: Determine if there is sufficient space between the back of the TV and the wall to connect all your cables before proceeding.
You may need to use the optional spacers to allow more clearance between the back of the TV and the wall.
or
NOTE: Adjust to shorten or hide the cords or or
Option 2: Attaching to a TV with a rounded back surface
Attach the left and right TV brackets (B and C) to the back of the TV using:
The M4 spacers (F), M4 washers (G), and the M4 screws (E).
Or
The M6 spacers (K), M6 washers (L), and the M6 screws (J).
M4 Bag
M4 × 12 mm
M6 Bag
M6 × 12 mm
M4 × 30 mm
M6 × 20 mm
M4
M6 × 35 mm
2 Install the wall plate
Option 1: Installing to a wood stud wall
1 Locate the stud. Verify the center of the stud with an awl or thin nail or use an edge to edge stud finder.
2 Level the wall plate (A) and mark the hole locations.
3 Drill the pilot holes as illustrated.
4 Align the wall plate (A) with the pilot holes, then place the washers (N) over the holes. Insert the lag bolts (O) through the washers, then tighten the lag bolts only until the washers are pulled firmly against the wall plate.
DO NOT over-tighten the lag bolts (O).
CAUTION: Avoid potential injuries or property damage!
Any material covering the wall must not exceed 5/8 in. (16 mm).
5/8 in.
(<16 mm)**
2.5 in.
(63.5 mm)*
*Drill the pilot hole to a depth of 2.5 in. (63.5 mm)
**Maximum thickness of any material covering
the stud or concrete surface.
M6
M4
Lag Bolt Bag
M6 or or or or
5/16 × 2½ in.
5/16 in.
Option 2: Installing to a solid concrete or concrete block wall
1 Level the wall plate (A) and mark the hole locations.
2 Drill the pilot holes as illustrated.
3 Insert the concrete wall anchors (M) into the pilot holes and make sure that the anchors are seated flush with the surface.
4 Align the wall plate (A) with the wall anchors, then place the washers (N) over the holes. Insert the lag bolts (O) through the washers, then tighten the lag bolts only until the washers are pulled firmly against the wall plate.
DO NOT over-tighten the lag bolts (O).
CAUTION: Avoid potential injuries or property damage!
Any material covering the wall must not exceed 5/8 in. (16 mm).
3 Mount the TV to the wall
Slide the upper notches on the TV bracket over
the upper flanges on the wall bracket.
CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks.
5/8 in.
(<16 mm)**
2.5 in.
(63.5 mm)*
*Drill the pilot hole to a depth of 2.5 in. (63.5 mm)
**Maximum thickness of any material covering
the stud or concrete surface.
4 Remove the TV from the wall
Unlatched
HEAVY! You will need assistance with this step.
Latched
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION: Do not use this product for any purpose not explicitly specified by Dynex. Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service or call a qualified contractor. Dynex is not responsible for damage or injury caused by incorrect installation or use.
The weight of your TV must not exceed 50 lb (22.7 kg). The wall must be capable of supporting five times the weight of the TV and wall mount combined.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!
3-year limited warranty
Visit www.dynexproducts.com for details.
We’re here for you
www.dynexproducts.com
For customer service, call:
800-305-2204 (U.S./Canada markets)
01 800-926-3020 (Mexico market)
© 2010 BBY Solutions, Inc., All Rights Reserved.
Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue
South, Richfield, MN USA 55423-3645
Best Buy Imports, S. de R.L. de C.V. Av. Santa Fe 485, Segundo
Piso, Colonia Cruz Manca, Programa Parcial de Desarrollo
Santa Fe, Delegación Cuajimalpa, Distrito Federal, México
05349
© 2010 Best Buy UK Distributions Limited. All rights reserved.
Distributed by Best Buy Europe Distributions Limited. 1 Portal
Way, London W3 6RS
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.
6907-002010 <00>
ENGLISH 10-0164
LO W - P R O F I L E T V M O U N T I Q U I C K S E T U P G U I D E I DX - T V M 1 1 2
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project