advertisement
EWB 1000 • Installation Guide
Overview
The Extron EWB 1000 wall box is an optional accessory for mounting the TLP 1000MV touchpanel onto the surface of various wall types
(such as drywall, wood, or masonry) where it is not possible to embed the touchpanel in the wall. The
EWB 1000 has knockouts that accept raceways or conduit for running cables over the surface of the wall to the touchpanel.
Planning
The following items are required for installation, but are not supplied: z Extron TLP 1000MV z z z z z z
Four mounting screws (Extron recommends a minimum length of 1 inch)
Power drill
Drill bit that is appropriate for wall type
Conduit or surface raceway to carry cables
Screwdriver
Level
IMPOR
TANT
:
Refer to www
.extron.com for e connecting ce.
the complete TLP 1000 Series user guide befor the pr oduct to the power sour
Extron
TLP 1000MV
Faceplate
Extron
TLP 1000MV
Extron
EWB 1000
Wall Box
Mounting Suggestions for Different Wall Types
Choose a type of screw or bolt that is appropriate for the wall on which you are mounting the EWB 1000 (see table below). The mounting holes in the back of the EWB 1000 accommodate screws up to ¼ inch in diameter.
Notes Wall Type
Drywall
Fasteners Min. Size
Fastener
Toggle bolts 3/16 inch
Quantity Drill Bit
Size
4 1/2 inch
Wood
(solid wall or stud)
Masonry
Wood screws #10 screw with a washer
Masonry screws
1/4 inch
4
4
1/16 inch wood bit
Min. 3/8 inch wall thickness
Min. 3/8 inch wall thickness
3/16 inch masonry bit
Do not mount to masonry joints
EWB 1000 • Installation Guide (Continued)
Mounting the EWB 1000
1. Decide where to mount the EWB 1000. If mounting to standard wood wall studs, locate the center of the studs.
2. Place the EWB 1000 against the wall at the mounting location. Use a level to ensure the box is horizontal and mark the position of the four holes.
3. If required, drill four holes into the wall.
4. Insert four screws (see the table on the previous page) and attach the EWB 1000 to the wall.
5. Remove the required knockout and run conduit or raceway to the EWB 1000.
6. Run cables through the conduit and the EWB 1000 knockout.
Mounting the TLP 1000MV
1. Remove the faceplate from the TouchLink panel.
2. Attach the cables to the back of the TLP 1000MV
(see the TLP 1000MV and
TLP 1000TV User Guide).
3. Secure the TLP 1000MV to the EWB 10000 using the four 6-32 screws provided.
4. Configure the TouchPanel as described in the TLP 1000MV
and TLP 1000TV User Guide.
5. Snap the faceplate into position (four clips on each side).
5
3
2
4
Mounting
Screws (4)
Extron USA - West
Headquarters
Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East
+800.633.9876
Inside USA and
Canada Only
+800.633.9876
Inside USA and
Canada Only
+800.3987.6673
Inside Europe Only
+800.7339.8766
Inside Asia Only
+1.714.491.1500
+1.714.491.1517 FA X
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
+971.4.2991800
+971.4.2991880 FAX
68-2096-01
Rev. A 04 11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project