- Home
- Domestic appliances
- Climate control
- Split-system air conditioners
- Daikin
- BRC7EB519
- User's manual
advertisement
Warning
Ask a qualified installer or contractor to install this product. Do not try to install the product by yourself.
Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion.
Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or contractor to install those parts and accessories. Use of unauthorised parts and accessories or improper installation of parts and accessories can result in water or refrigerant leakage, electrical shock, fire or explosion.
Read the User's Manual carefully before using this product. The User's Manual provides important safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any enquiries, please contact your local importer, distributor and/or retailer.
Cautions on product corrosion
1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.
2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided. If you need to install
the outdoor unit close to the sea shore, contact your local distributor.
AIR CONDITIONING SYSTEM
COOLING ONLY [50Hz]
PCSHK1010C
Specifications, designs and other content appearing in this brochure are current as of July 2013 but subject to change without notice.
All rights reserved 07/13 SS
HFC R-410A Line Up for Stores and Offices.
CEILING MOUNTED
CASSETTE TYPE
WALL MOUNTED TYPE
CEILING SUSPENDED TYPE
1
P r o d u c t L i n e u p
71 Series
CEILING MOUNTED
CASSETTE TYPE
Round Flow
Indoor unit
Outdoor unit
CEILING SUSPENDED TYPE
FCQ71LUV1
RR71MV1 / Y1
100
FCQ100LUV1
RR100MY1
125 140
FCQ125LUV1
RR125MY1
FCQ140LUV1
RR140MY1
Page 3
Page 7
WALL MOUNTED TYPE
Indoor unit
Outdoor unit
FHQ71BVV1B
RR71MV1 / Y1
FHQ100BVV1B
RR100MY1
NEW
FHQ125BVV1B
RR125MY1
Page 9
Indoor unit
Outdoor unit
FAQ71BVV1B
RR71MV1 / Y1
FAQ100CVEA
RR100MY1
DUCT CONNECTION
MIDDLE/HIGH STATIC
PRESSURE TYPE
Indoor unit
Outdoor unit
FBQ71DV1
RR71MV1 / Y1
FBQ100DV1
RR100MY1
FBQ125DV1
RR125MY1
FBQ140DV1
RR140MY1
Page 11
Page 13
RR71MV1
RR71MY1
RR100MY1 RR125MY1
O U T D O O R U N I T
RR140MY1
DUCT CONNECTION MIDDLE/HIGH STATIC
PRESSURE TYPE
OUTDOOR UNIT
2
CEILING MOUNTED CASSETTE TYPE
Round Flow
FCQ71LU/100LU/125LU/140LU
Option
Accessory required for indoor unit
Wired LCD remote controller
BRC1C61
Wireless LCD remote controller
A signal receiver must be added to the indoor unit.
BRC7F633F
Signal receiver unit
(Installed type)
Wireless remote controller and signal receiver unit are sold as a set.
Wired LCD remote controller with weekly schedule timer
Navigation Remote
Controller
(Wired Remote Controller)
Features
Comfort Remote controller Cleanliness Work & Servicing
BRC1D61 BRC1E62
Control features Options Others
3
• • • • •
*1
•
*2
* 1 Applicable when wired remote controller is used
* 2 Applicable when BRC1E62 is used
* 3 Applicable when BRC1D61 or BRC1E62 is used
* 4 Applicable when BRC1C61 is used
* 5 For the outdoor units
*2 *3 *2 *4
• • •
*5
• • • • • • • • • • • • • • •
*5
Avoids uneven temperature and discomfort caused by drafts.
Comfort enhanced by Round Flow!
360° airflow
With uniform temperature distribution
Air movement is gentle with Round Flow
Enhanced Comfort
Airflow distribution
Creates uniform comfort throughout the space
360° airflow can maintain comfort even if air discharge speed is lower.
Greater comfort
Improved energy saving
If you raise the set temperature by 1 to
1.5°C,and velocity is decreased by 25%, you still obtain the same feeling temperature and comfort.
Adapts easily to the installation space.
Because air flows out from corner outlets, comfort spreads more widely.
Typical flow patterns There are a total of 23 flow patterns.
All-round flow 3-way flow
L-shaped
2-way flow
Opposite
2-way flow
(E.g., installed in middle of ceiling)
4-way flow also possible.
(E.g., installed near a wall)
(E.g., installed in a corner)
(E.g., installed in a long room)
Note: Whatever the discharge direction, the same type of panel is used. If installing for other than all-round flow, an air discharge outlet sealing material (option) must be used to close each unused outlet.
Operation sound increases when using 2-way or 3-way flow.
Grime prevention and bactericidal coating: Make cleaning easier.
External panels are treated with a coating that repels dirt.
Treated surface
Untreated surface
To prevent dirt sticking to the external panels, they have been coated with a surface treatment.
Resists soiling
Grimy surface
• Condition after exposure to the smoke of 600 cigarettes in 1 m 3 enclosed space.
Silver ion anti-bacterial drain pan
Mould-proof drain pan includes a silver ion antibacterial agent that assists in preventing the growth of slime, bacteria, and mould that cause smells and clogging.
Non-flocking flaps
Condensation does not easily form on and dirt does not cling to non-flocking flaps.
It is easy to clean.
Filter has anti-mould and bactericidal treatment
Prevents mould and microorganisms growing out of the dust and moisture that adheres to the filters.
4
CEILING MOUNTED CASSETTE TYPE
Round Flow
Fine square panels
Panel size is same for all models, FCQ71-140LU.
It is easy to maintain a neat appearance when multiple units are installed.
950 mm
950 mm
Same for all models
Compact body and quiet operation
dB(A)
Indoor unit
71LU
100LU
125LU
140LU
High
35
43
44
44
Low
28
32
34
36
Note : Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
Optimal comfort and convenience assured by air discharge modes
Note: Air direction is set to the standard position when the unit is shipped from the factory.
The position can be changed from the remote controller.
Air direction
Desired situation
Standard setting
Standard position to prevent draft.
Setting to prevent soiling of ceiling *
Recommended for shops with light coloured ceilings that must be kept spotless.
Auto-swing
Auto-swing between
15° and 60°
Auto-swing between
25° and 60°
5-levels air direction setting
Settable to 5 different levels between 15° and 60°
Settable to 5 different levels between 25° and 60°
Auto air direction control
The air direction is set automatically to the memorised position of the previous air direction.
*Closing of the corner discharge outlets is recommended.
Suitable for high ceilings
Even in spaces with high ceilings, a comfortable airflow is carried down to the floor level.
Criteria for ceiling height and number of air discharge outlets
(Ceiling height is reference value)
Ceiling height
Standard
High ceiling
High ceiling
All round flow
2.7 m
3.0 m
3.5 m
Number of air discharge outlets used
71LU 100LU–140LU
4-way flow
3.1 m
3.4 m
4.0 m
3-way flow
3.0 m
3.3 m
3.5 m
2-way flow
3.5 m
3.8 m
-
All round flow
3.2 m
3.6 m
4.2 m
4-way flow
3.4 m
3.9 m
4.5 m
3-way flow
3.6 m
4.0 m
4.2 m
Note: Factory settings are for standard ceiling height and all-round flow.
High ceiling settings (1) and (2) are set with the remote controller by field setting.
2-way flow
4.2 m
4.2 m
-
Two selectable temperature-sensors
Both indoor unit and wired remote controller (option
(BRC1D61,BRC1E62)
) contain temperature- sensors. Temperature sensing can be set at the unit or, to further improve comfort level, closer to the target area at the wired remote control. This feature must be set during commissioning by the technicians.
*Temperature-sensor on indoor unit must be used when the air conditioner is controlled from another room.
**Wireless remote controller does not have a temperature-sensor.
Switchable fan speed: High/Low
High setting provides maximum reach while low setting minimises drafts.
5
On/Off timer
Operation starts when the preset time of the ON timer elapses and stops when the preset time of the OFF timer elapses.
Quick and easy to install
Just 256 mm high. Installable in tight ceiling spaces
(71LU)
256 mm * 1
266 mm * 2
*1 298 mm high with 100LU–140LU
*2 308 mm high with 100LU–140LU
Easy height adjustment
Each corner of the unit has an Adjuster Pocket that lets you easily adjust the unit's suspended height.
Note: If the wireless remote control option is installed, a light receptor unit is housed in one of the adjuster pockets.
All models can be installed without using lifter because of the light weight.
Installable in any direction
Since the orientation of the intake grill can be adjusted after installing, the direction of the intake grill lines can be unified when multiple units are installed.
Drain pump is equipped as standard accessory with 850 mm lift.
850 mm
175 mm
Transparent drain socket
Because the drain socket is transparent, after the drain piping has been installed, it is easy to check if the drain come out through the socket.
Connection to a centralised control system is available without option
Easier to maintain
The condition of the drain pan and drain water can be checked by removing the drain plug and intake grille.
Drain plug
Just open the intake grille!
With ultra-long-life filters (option), maintenance is not required in normal shops or offices for up to four years.
Options required for specific operating environments
Ultra-long-life filter
Even in smoky environments where the air conditioning is on most of the time, the ultra long-life filter only has to be changed once a year.
Smoky atmosphere: annual filter change
*For dust concentration of 0.3 mg/m 3 (Requires separately sold Air Cleaner.)
1 year (Approx. 5,000 hr) 15 hr/day x 28 day/month x 12 month/year
Ordinary store or office: filter change every 4 years
*For dust concentration of 0.15 mg/m 3
4 years (Approx. 10,000 hr) 8 hr/day x 25 day/month x 4 years
High-efficiency filter
Available in two types: 65% and 90% colorimetry.
Fresh air intake kit
Using this kit, a duct can be fitted to increase the intake of outdoor air.
Outside
Note: *Connecting ducts, insect nets, fire dampers, air filters, and other parts should, as required, be procured locally.
**Outside Air fan interlocked with air conditioning unit is necessary.
Optional PCB(KRP1C63)is required for interlocking.
***It is recommended that the volume of outdoor air introduced through the kit is limited to 10% of the maximum airflow rate of the indoor unit. Introducing higher quantities will increase the operating sound and may also influence temperature sending.
Panel spacer
Use when only minimal space is available between drop ceilings and ceiling slabs.
40 mm
Panel spacer
Note: Some ceiling constructions may hinder installation.
Contact your Daikin Dealer before installing your unit.
Sealing material of air discharge outlet
Sealing material block air discharge openings not used in
2-way or 3-way blow.
Branch duct (direct-connection round duct)
A round duct can be attached without the need for a chamber.
A flanged port for direct connection of a round duct is provided. An existing branch duct chamber can also be fitted
(square slit hole).
The units can be installed in the following different ways.
Chamber type Chamber type
(without T-joint pipe and fan) (with T-joint pipe and without fan)
KDDP55B160 KDDP55B160K
Flexible duct
(procured locally)
T-joint pipe
(procured locally)
Flexible duct
T-joint pipe
Direct installation type
KDDP55X160
Suction chamber
Connection chamber
Intake duct
(procured locally)
(duct length: 4 m max.)
Note: Use of options will increase operating sound.
Suction chamber
Connection chamber
Intake duct
(procured locally)
(duct length: 4 m max.)
Duct flange
(with insulation
material)
Intake duct
(procured locally)
6
CEILING SUSPENDED TYPE
Quiet and compact system.
FHQ71BV / 100BV / 125BV
Option
Accessory required for indoor unit
Wired LCD remote controller
BRC1C61
Wireless LCD remote controller
A signal receiver must be added to the indoor unit.
BRC7EA66
Signal receiver unit (Installed type)
Wireless remote controller and signal receiver unit are sold as a set.
Wired LCD remote controller with weekly schedule timer
Navigation Remote
Controller
(Wired Remote Controller)
Features
Comfort
BRC1D61
Remote controller Cleanliness Work & Servicing
BRC1E62
Control features Others
7
• • •
*1 *2
•
*3
* 1 Installable on max. 3.5 m high ceiling
* 2 Applicable when wired remote controller is used
* 3 Applicable when BRC1E62 is used
* 4 Applicable when BRC1D61 or BRC1E62 is used
* 5 Applicable when BRC1C61 is used
* 6 Option
* 7 For the outdoor units
*3 *4 *3 *5
•
*6 *7
• • • • • • • • • •
*7
Diffuses comfortable air throughout the room
Auto-swing (up&down) brings comfort to the room.
Wide air discharge openings produce a spreading 100° airflow
Air is blown up to 50° in the downward direction.
Quiet operation
Sound operation has been reduced on the exposed ceiling suspended type unit.
dB(A)
Indoor unit High Low
71BV
100BV
39
42
44
35
37
39 125BV
Note : Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
Uses quiet stream fan and other quiet technologies.
50°
100°
Installable on ceilings 3.5 m high
Two selectable temperature-sensors
Both indoor unit and wired remote controller (option
(BRC1D61,BRC1E62)
) contain temperature- sensors. Temperature sensing can be set at the unit or, to further improve comfort level, closer to the target area at the wired remote control. This feature requires initial setting by the installer.
*Temperature-sensor on indoor unit must be used when the air conditioner is controlled from another room.
**Wireless remote controller does not have a temperature-sensor.
Switchable fan speed: High/Low
Programme "Dry"
Dehumidification is microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature.
Turbulent flow
is reduced
Straightening plate
Quiet stream fan
Easier to maintain
Long-life filter lasts about half year * maintenance not required
* For dust concentration of 0.15 mg/m 3
Two time settings (2500 hrs and 1250 hrs) are available to match the installation environment. Maintenance time warning is displayed on the remote controller (filter sign).
Non-flocking flap
Condensation does not easily form on and dirt does not cling to non-flocking flap.
It is easy to clean.
Non-flocking flap
Easy-clean, flat surfaces
It is easy to wipe dirt off the flat side and lower surfaces of the unit.
Installation flexibility for freedom of design
Uniform height and depth. Compact design for small-capacity models to meet tighter dimensional constraints.
Indoor unit
Height
Width
Depth
71BV
1,160
(mm)
100BV 125BV
195
1,400
680
1,590
For all maintenance tasks, access is from bottom surface.
Flexible installation
The unit fits more snugly into tight spaces.
30 mm
or more
30 mm
or more
*Water used in the test-run can now be drained from the air discharge opening rather than from the side as was formerly the case.
Drain pump kit (option) can be easily incorporated
Drain pipe connection can be done inside the unit. refrigerant and drain pipe outlets are at the same opening.
600 mm
Drain pump kit
(built inside main unit)
All wiring and internal servicing can be done from under the unit
Pipes more easily rigged, too
Plastic panels are used to conceal piping holes. Holes can be easily punched out without requiring special tools.
Oil resistant grille
Oil-resistant plastic is used for the air suction grille.
This satisfies durability in restaurants and other similar environments.
Note: Intended for use in salons, dining rooms, and ordinary sales floors, this specification is not suitable for kitchens or other harsh environments.
8
WALL MOUNTED TYPE
Compact design and easy installation
F A Q 7 1 B V / 1 0 0 C
FAQ71BV
NEW FAQ100C
Features
Comfort
Option
Accessory required for indoor unit
Wired LCD remote controller
BRC1C61
Wireless LCD remote controller
A signal receiver must be added to the indoor unit.
71BV
100C
BRC7EA619
BRC7EB519
71BV
100C
Signal receiver unit (Installed type)
Wireless remote controller and signal receiver unit are sold as a set.
Wired LCD remote controller with weekly schedule timer
Navigation Remote
Controller
(Wired Remote Controller)
BRC1D61
Remote controller Cleanliness Work & Servicing
BRC1E62
Control features Others
9
•
*1 *2 *3
• •
*4
•
* 1 FAQ71: 2 step, FAQ100: 3 step
* 2 FAQ100 only
* 3 Applicable when BRC1E62 is used
* 4 Applicable when wired remote controller is used
*3 *3 *5 *3 *6
•
*7 *8
* 5 Applicable when BRC1D61 or BRC1E62 is used
* 6 Applicable when BRC1C61 is used
* 7 Option
* 8 For the outdoor units
• • • • • • • • • •
*8
340 mm
Compact &
Sophisticated design
FAQ100
9 kg lighter
FAQ100BV FAQ100C
Height 360 mm 340 mm
Width 1,570 mm 1,200 mm
Depth 200 mm 240 mm
1,200mm
370mm shorter Weight 26 kg 17 kg
Flaps are closed when not operating
Comfortable
Auto swing (up and down) and wide-angle louvers
(left and right by hand) facilitate even room temperature
Wide-angle louvers
(by hand)
Soft material louver bends airflow over a wider area
An air discharge modes ensure comfortable air distribution across the entire room
Auto-swing 5-level air direction setting Auto-air direction control
Auto-swing from 10 to 70
10°
70°
10°
Gettable to 5 different levels between 10 to 70
70°
10°
The air direction is set automatically to the memorised position of the previous air direction.
(Initial setting is 10 for cooling .)
Comfort even on the far side of the room
To carry air to the far side of long rooms, extra-high airflow adds 10% more fan speed the "high" setting.
Air discharge strength is selected from the remote controller.
Easy installing and servicing
6-direction piping offers greater installation flexibility.
Left pipe
Back-left pipe
Bottom-left pipe
Right pipe
Bottom-right pipe
Back-right pipe
Maintenance possible from the front of the unit
All maintenance tasks can be carried out via front access. During service work, attachment and detachment of parts is easier.
Drain pump kit is available as option.
Installs onto side of unit.
Height of drain up
Refrigerant piping
1,000 mm
Drain pump kit
Drain pump kit can be installed on either left and right side of the air conditioner.
Indoor unit
Connection to a centralised control system is available without option
Easy cleaning
Removable and washable grille
Two selectable temperature-sensors
Switchable fan speed: High/Middle/Low
(FAQ100)
: High/Low
(FAQ71)
Auto airflow rate (FAQ100 only when BRC1E62 is used)
Programme "Dry"
Dehumidification is microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature.
Flat panel, easy to wipe dust off
(FAQ100)
Non-flocking flaps
Condensation does not easily form on and dirt does not cling to non-flocking flaps.
It is easy to clean.
10
DUCT CONNECTION MIDDLE HIGH STATIC PRESSURE TYPE
FBQ71D/100D/125D/140D
Option
Accessory required for indoor unit
Wired LCD remote controller
BRC1C61
Wireless LCD remote controller
A signal receiver must be added to the indoor unit.
BRC4C64
Signal receiver unit
(Separate type)
Wireless remote controller and signal receiver unit are sold as a set.
Wired LCD remote controller with weekly schedule timer
Navigation Remote
Controller
(Wired Remote Controller)
Features
Comfort Remote controller Cleanliness Work & Servicing
BRC1D61 BRC1E62
Control features Option Others
11
• •
*1
•
*2 *2 *3
* 1 Applicable when wired remote controller is used
* 2 Applicable when BRC1E62 is used
* 3 Applicable when BRC1D61 or BRC1E62 is used
* 4 Applicable when BRC1C61 is used
* 5 Option
* 6 For the outdoor units
*2 *4 *5
• •
*6 *5
• • • • • • • • • • •
*6
Increased freedom of design thanks to variable control over external static pressure
Comfort airflow achieved in accordance with conditions such as duct length.
Using a DC fan motor, the external static pressure can be controlled within a range of 50 Pa to 200 Pa.
Freely control external static pressure
50 Pa 200 Pa
Set to low static pressure when ducts are short.
Set to high static pressure for advanced needs such as when using dampers and long ducts.
Reduced installation time
Use remote controller to adjust airflow
When testing standard integrated ceiling units that employ duct work, much time used to be required to adjust airflow to the right level. Thanks to the ability provided by Daikin to automatically perform this troublesome adjustment using a remote controller, this step is now quick and easy. (Adjust by H tap .)
1. Adjust to approximately ±10% of the rated H tap airflow.
2. Once actual operation has begun, adjustment of the rated airflow is not possible.
Connection to a centralised control system is available without option
Quiet operation
High
Low
71D
37
32
100D
38
33
300
125D
40
36 dB(A)
140D
40
36
Thin, lightweight indoor unit makes delivery and installation easy.
With a height of only 300 mm, installation is possible even in buildings with narrow ceiling spaces.
300 mm
Easy maintenance
Maintenance is easy because the drain pan can be removed.
Clean
Silver ion anti-bacterial drain pan
Mould-proof drain pan includes a silver ion antibacterial agent that assists in preventing the growth of slime, bacteria, and mould that cause smells and clogging.
Indoor unit
Height
(mm)
Width
(mm)
Depth
(mm)
Machine Weidth
(kg)
71D
1,000
36
100D 125D
300
1,400
700
46
140D
Drain pump is equipped as standard accessory with 700 mm lift.
700 mm
Comfortable
Two selectable temperature-sensors
Both indoor unit and wired remote controller (option) contain temperature- sensors. Temperature sensing can be set at the unit or, to further improve comfort level, closer to the target area at the wired remote control.
This feature requires initial setting by the installer.
*Temperature-sensor on indoor unit must be used when the air conditioner is controlled from another room.
**Wireless remote controller does not have a temperature-sensor.
Simultaneous air conditioning of two rooms and ventilation grille (ventilation opening)
When air conditioning two rooms simultaneously, the air discharged into each room must be circulated back to the air conditioner. To achieve this, a ventilation duct should be installed for each room or one of the indicated ventilation grilles should be installed on the partitioning wall or under the door between the rooms.
Partitioning wall
Ventilates air through the partitioning wall.
(See right)
Door-installed ventilation grille
Ventilation grille
Wall-installed ventilation grille
Ventilation grille
Under-door cutout
Under-door cutout
Note: The under-door cutout method should be used only when there is a small volume of airflow.
12
OUTDOOR UNIT
OUTDOOR UNIT
13
RR71MV1
RR71MY1 RR100MY1 RR125MY1 RR140MY1
Easy installation and maintenance
Pre charged for up to 30 metres
If refrigerant piping length does not exceed
30 m, there is no need for on-site gas charging.
70 m piping length
4-direction piping offers greater layout freedom
The outer panel for the piping connection part of the front, right side and backside can be removed and is easier for post-installation piping work.
Allowed refrigerant pipe length and
level difference
Pre charged 1
ALL model
30 m
Max. length
70 m
(Equivalent length 90m)
Max. level difference
30 m
Note: 1 Additional refrigerant charging is required if
the refrigerant pipe is longer than the length.
Separation available
Easy centralised installation with the module oriented design
Depth of 71-140M are standardised as 320 mm. Horizontal continuous mounting is available.
Facilitates pump down
(Refrigerant recovery function)
A pump-down switch is provided to make it easier to collect refrigerant if the unit is to be moved or layout modified.
*Pump-down function is available for pre-charged refrigerant amount.
Suction
320 mm
Discharge
71M 100M 125M 140M
900 mm 900 mm 900 mm 900 mm
Compact
Slim-design and low-profile compact outdoor units
Compactly designed outdoor unit with interior layout organised for the smooth flow of air.
40
30
20
10
0
-10
-20
Operation range
Suited for year-round cooling applications
Cooling is efficient even in winter when indoor temperatures are higher than those outside, such as in underground public spaces or offices with many computers.
Wide operation range
(Applies to RR71-125M)
50
46
˚C
DB
Outdoor temp
(˚CDB)
Safety
Cooling
-15
˚C
DB
Reinforcing wire fittings
(option) are available
Fittings can be mounted on the four locations, right/ left on front and back side of the outdoor unit.
Durability
Heat exchange fins provided with anti-corrosion treatment
Construction
Non-treated fin
PE fin
Aluminium
Hydrophilic film
Aluminium
Corrosion resistant acrylic resin
Example of installation service space for outdoor unit
For RR71MV1, RR71-140MY1
The values represent the case for the RR71-140 type. The values in ( ) are for RR71 type. (The unit values is mm. )
1 When there is an obstruction on the inlet side
1) When the overhead space is open
1. For single unit installation
When there is an obstruction only on the inlet side
100(50) or more
When there are obstructions on both sides
2 When there is an obstruction on the outlet side
1) When the overhead space is open
1. For single unit installation
2. For multiple units installation
(more than two units)
500 or more
2. For multiple units installation
(more than two units)
When there are obstructions on both sides
1000 or more
100 or more
100 or more
200 or more
100 or more
300(200) or more
2) When there is an obstruction
in the overhead space
1. For single unit installation
When there is an obstruction on the inlet side
An obstruction in the overhead space
500 or less
100 or more
When there are obstructions on the inlet side and both sides
An obstruction in the overhead space
150 or more
500 or less
150 or more
150 or more
2. For multiple units installation (more than two units)
When there are obstructions on the inlet side and both sides
500 or less
An obstruction in the overhead space
1000 or more
2) When there is an obstruction
in the overhead space
1. For single unit installation
An obstruction in the overhead space
2. For multiple units installation
(more than two units)
An obstruction in the overhead space
1000 or more
3 When there are obstructions on both the inlet and outlet sides
(When the obstruction on the outlet side is higher than the
unit itself)
1) When the overhead space is open
(There is no limit to the height of the obstruction on the
outlet side.)
1. For single unit installation
L H
2. For multiple units installation
(more than two units)
1000 or more
500 or less
500 or more
500 or less
500 or more
100(50)
or more
200 or more
300(200) or more
L H
Note : As for other patterns of installation, please refer to Installation manual or Engineering Data Book.
1000 or more
300(200)
or more
14
Wired LCD remote controller
LCD REMOTE CONTROLLER
Necessary optional accessory
15
Easy-to-read LCD remote controller allows various system control configurations and can control multiple indoor units.
Remote controller options are shown on the page introducing each indoor unit model.
NEW
Navigation Remote Controller
(Wired Remote Controller BRC1E62)
This simple, modern designed remote controller with fresh white colour matches your interior design. Operation is much easier and smoother, just follow the indications on the navigation remote controller.
Wired LCD remote controller
Easy to read because of large LCD screen.
The rubber switch and the oil-resistant plastic casing are adopted for durability.
Only 17 mm thick. Can be installed either recessed or exposed.
Wired remote controller has built-in temperature-sensor
(Applies to wired remote controllers
(BRC1C61,BRC1D61,BRC1E62)
)
Enables temperature sensing closer to target area for improved comfort. (When using remote control from another room, temperature-sensor in indoor unit's air inlet must be selected.)
BRC1C61
Dot matrix display
A combination of fine dots enables various icons.
Large text display is easy to see.
Clear Display
Energy saving
NEW Setpoint auto reset
- Even if the set temperature is changed, it returns to the preset temperature after apreset period of time.
- Period selectable from 30min/60min/90min/120min.
Restaurant sample
Restaurant opened
Temperature is set to 27ºC
27 °C
Full tables at lunchtime
Then is lowered to 24ºC for crowded room
24 °C
After 30 minutes*
Automatically returns to preset temperature (27ºC)
Returns to
27 °C automatically
Backlight display
NEW Setpoint range set
- Saves energy by limiting the min. and max. set temperature.
- Avoids excessive heating or cooling.
- This function is convenient when the remote controller is installed at a place where any number of people may operate it.
Wired LCD remote controller with weekly schedule timer
Remote control is equipped with weekly timer function.
24-hour clock function.
Programming function for each day of week.
Scheduling possible of start/stop and temperature limit (5 settings/day).
BRC1D61
LCD wireless remote controller
Light receptor mounted type
The wireless remote controller is supplied in a set with a signal receiver.
Shape of signal receiver unit differs according to the indoor unit.
Wireless remote controller
BRC7F633F
Signal receiver unit
(For ceiling mounted
cassette type)
Note: The signal receiver unit shown in the photograph is for mounting inside the decoration panel of the ceiling mounted cassette type.
Facilitates maintenance and repair
All initial settings can be set from the remote controller. After interior construction is complete, ceiling mounted cassette type can be remotely set without having to use stepladder access for manual setting.
Setting contents: High ceiling use, air direction, filter type, address for centralised control (group control address is set automatically).
Remote controller is equipped with model name and failure display functions. This facilitates service in the unlikely event of a malfunction.
(Applies to wired remote controller
(BRC1E62)
)
SkyAir shares common control with
Heat Reclaim Ventilator and the other Daikin air-conditioning units, thus simplifying interlocking operations.
Easily adaptable to large-scale, high-function, centralised remote control systems.
Installing and connecting control wiring between
SkyAir and other Daikin air-conditioning equipment is easy.
*Please refer to page 17 for more details.
*Setting possible for after 30, 60, 90, and 120
minutes. Off timer (programmed)
- Turns off the air conditioner after a preset period of time.
- Period can be preset from 30 to 180 minutes in10-minute increments.
Indoor units applicable for the remote controller
Signal receiver unit is contained inside decoration panel or indoor unit
CEILING MOUNTED CASSETTE TYPE
CEILING SUSPENDED TYPE
WALL MOUNTED TYPE 71BV
100C
DUCT CONNECTION MIDDLE HIGH STATIC PRESSURE TYPE
BRC7F633F
BRC7EA66
BRC7EA619
BRC7EB519
BRC4C64
Convenience
Weekly schedule
NEW
- 5 actions per day can be scheduled for each day
of the week.
- The holiday function will disable schedule timer
for the days that have been set as holiday.
- 3 independent schedules can be set.
(e.g. summer, winter, mid-season)
Multilingual display
Display is available in 11 languages.
(English, German, French, Spanish,
Italian, Portuguese, Greek, Dutch,
Russian, Turkish, and Polish).
LCD panel shows operating status in letters, numbers, and motion.
Airflow / swing display
Preset temperature / operation mode display
Programming time display
Self-diagnosis function
Displays auto-swing operating status and setting position of air discharge angle.
Displays preset room temperature and operating status (fan, dry, cool).
Operation start and stop time can be set for individual timers up to 72 hours. The LCD also shows when it is time to clean the filter, when changeover is under centralised control, and ventilation/cleaning.
Monitors operating status within the system covering 40 items, and displays a message to indicate as soon as a malfunction occurs.
16
Simple system provides a diverse assortment of control modes.
Control pattern Wired remote controller Wireless remote controller
Control by 1 remote controller
(Basic system)
Control by 2 remote controllers
For control from 2 locations such as in room and control room, exits, etc.
Non-polar, double-core
(max. wiring length 500 m)
Signal receiver unit installed on indoor unit
Control by 1 wireless remote controller and 1 wired remote controller (See note 2, 3)
Signal receiver unit installed on indoor unit
Connects 2 wired remote controllers (See note 1)
Group control
For simultaneous control of up to 16 indoor units.
Automatic address setting function Automatic address setting function
Signal receiver unit installed on 1 indoor unit
Control by external command
Operation and surveillance is carried out using the contact signal from the operation control box in the building surveillance (security) room.
Optional wiring adaptor for electrical appendices is necessary
Central remote controller (option)
Optional wiring adaptor for electrical appendices is necessary
Central remote controller (option)
Centralised remote control
Centralised control of up to 64 indoor groups from remote location up to 1 kilometer away.
Optional SkyAir series interface adaptor required (See note 4)
Optional SkyAir series interface adaptor required (See note 4)
Heat Reclaim
Ventilator
Heat Reclaim
Ventilator
Link by remote controller group control.
Can be operated simultaneously or independently by remote controller
(set by ventilation mode)
Can be operated simultaneously by remote controller
(set by ventilation mode)
Interlock control with Heat Reclaim
Ventilator
Central remote controller (option) Central remote controller (option)
Zone link control by centralised control.
Heat Reclaim
Ventilator
Heat Reclaim
Ventilator
Heat Reclaim Ventilator for indoor units within a zone are operated by interlocking Can also be operated independently by remote controller.
Heat Reclaim Ventilator for indoor units within a zone are operated by interlocking
Note:1.BRC1E62 can connect to BRC1E62 only.
2.It is not possible to use two wireless remote controllers.
3.BRC1E62 cannot connect to wireless remote controller.
4.The ceiling mounted cassette type <Round Flow>, wall mounted type, and duct connection middle/high static pressure type come standard with an interface adaptor for SkyAir series.
Easily adaptable to large-scale, high-function, centralised remote control system.
Central remote controller Unified on/off controller Schedule timer
DCS601C51 (Option)
DCS302CA61 (Option) DCS301BA61 (Option) DST301BA61 (Option)
17
Centralised control, with setting as simple as it is with a standard remote controller, of up to 64 groups
(1,024 indoor units) is possible.
Centralised control of on/off by group or all at once for up to 256 indoor units.
Interface adaptor for SkyAir series
DTA112BA51 (Option)
Unified control of weekly schedule for up to 1,024 indoor units.
Schedule timer sets on/off time in 1 minute units to be executed twice a day for a week at a time.
Enables centralised control via connection to a high-speed, DIII-NET communication system, adopted for the Daikin VRV system.
Necessary for interface adaptor for SkyAir series with the central remote control units shown at above.
With its high functionality, the full colour “all-in-one” graphic controller facilitates management of SkyAir
System in a variety of ways.
The interface adaptor for the SkyAir series is optional except for the ceiling mounted cassette type <Round Flow>, wall mounted type, and the duct connection middle/high static pressure type.
Abundance of functions that provide comfortable air-conditioning in stores and offices.
Note: Some features only available on selected models. See model pages for full list of features applicable to each unit.
Comfort
Auto-swing
Delivers comfortable air-conditioning to all areas, near to and far from the air-conditioner.
The air flow direction can be fixed at your desited angle by the remote controller.
High-ceiling application
Delivers air-conditioning comfort all the way down to the floor in air-conditioning zones with high ceilings.
Swing pattern selection
(standard, ceiling soiling prevention)
You can freely set 2 air discharge setting by remote controller.
(1) Air direction in standard setting
(2) Air direction in ceiling soiling prevention setting
Note:When units are installed on high ceilings, depending on the model, various restrictions concerning maximum height, air discharge direction, and choice of options may apply.
Switchable fan speed
High setting provides maximum reach while low setting minimises drafts.
Auto airflow rate
Airflow rate is automatically controlled in accordance with the difference between room temperature and set temperature.
Two selectable temperature-sensors
Temperature-sensors are included in the indoor unit and optional wired remote controller. Temperature sensing closer to target area is possible to further increase the comfort level.
Use the temperature-sensor in the indoor unit when controlling air conditioning from another room.
Note: Wireless remote controllers have no temperature-sensor.
Programme "Dry"
Dehumidification is microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature. Useful for reducing uncomfortable humidity without uncomfortable cooling of the room.
High fan speed mode
You can increase fan speed approximately 10% higher than the "high" setting.
Applicable for wall mounted type
Year-round cooling applicable
Efficient cooling even in winter when indoor temperatures are higher than those outside, such as in underground public spaces or offices with many computers.
The year-round cooling kit is required as option.
Remote Controller
Setpoint auto reset
Even if the set temperature is changed, it returns to the preset temperature after a preset period of time.
Setpoint range set
Saves energy by limiting the minimum and maximum set temperatures. Avoids excessive heating and cooling.
Weekly schedule timer
Up to five operation ON/OFF settings can be programmed per day for each day of the week. Not only can the time be set for the operation ON setting, but also the temperature.
Cleanliness
Anti-bacterial air filter
The Air filter has a anti-bacterial treatment to help prevent the growth of bacteria and mould on it.
Mould-proof air filter
Sanitary filter has mould-resistant treatment.
Off timer (programmed)
Sets and saves setting for an increment of time that automatically turns off air conditioner after a preset period of time for each time operation starts.
On/Off timer
Operation starts when the preset time of the ON timer elapses and stops when the preset time of the OFF timer elapses.
Silver ion anti-bacterial drain pan
Mould-proof drain pan includes a silver ion antibacterial agent that assists in preventing the growth of slime, bacteria, and mould that cause smells and clogging.
Mould-proof drain pan
Mould-proof drain pan prevents growth of mould in highly humid conditions.
18
19
Note: Some features only available on selected models. See model pages for full list of features applicable to each unit.
Work and Servicing
Drain pump mechanism
Steeper gradient realises more efficient condensate drainage.
High-lift is especially useful for long lengths of drain piping.
Filter sign
The filter sign warns you when it is time to clean the filter.
*When using a wired remote controller the sign is displayed in the LCD.
When using a wireless remote controller the filter sign lamp illuminates on the signal receiver unit.
Pre charged for up to 30 metres
If refrigerant piping length does not exceed 30 m, there is no need for on-site gas charging.
Emergency operation
If there is a malfunction elsewhere in the system, the fan or compressor can still be operated.
Long-life filter
Maintenance is not required for one year (two years when a ceiling mounted cassette type is used).
Ceiling soiling prevention function
Daikin's innovative air discharge mechanism keeps airflow away from the ceiling. Ceiling cleaning is less frequently required.
Self diagnosis function
The operating parameters of indoor and outdoor units, and sensor data at critical locations throughout the system, are constantly monitored using a microcomputer. To facilitate quick response in the event of a malfunction, a message appears on the LCD of the remote controller and an LED on the unit illuminates.
Control features
Auto-restart
If there is a power outage while the equipment is operating, operations will restart in the same mode as before the power cut when electricity is restored.
Control by 2 remote controllers
Using 2 remote controllers you can operate the equipment locally or from a remote location.
Note: When a wireless remote controller is used, remote control by two remote controllers is not possible.
Group control by 1 remote controller
You can turn up to 16 indoor units on/off with a single remote controller. (When using connected indoor units, the settings must all be the same and on/off will be simultaneous.)
External command control
Operation and surveillance is carried out using the contact signal from the operation control box in the building surveillance (security) room.
*Required for KRP58M51 (Option)
Central remote control
Optional central remote controller enables centralised control of up to 1024 indoor units (64 groups) from up to 1 kilometer away.
Interlock control
Enables interlocking control with external equipment such as
Heat Reclaim Ventilator.
DIII-NET communication standard
Standardly equipped interface enables connection to centralised control system without need of an adaptor.
Options
Ultra long-life filter
Requires no maintenance for about 4 years* (10,000h) in stores and offices.
*For dust concentration of 0.15 mg/m 3
High-efficiency filter unit
Two types are available: 65% and 90% colorimetry.
Fresh-air intake kit
You can provide air-conditioning with fresh air from outside.
Convenient for places where a ventilation fan cannot be installed.
Note: *Connecting ducts, insect nets, fire dampers, air filters, and other parts should, as required, be procured locally.
**Outside Air fan interlocked with air conditioning unit is necessary. Optional
PCB(KRP1C63)is required for interlocking.
***It is recommended that the volume of outdoor air introduced through the kit is limited to 10% of the maximum airflow rate of the indoor unit. Introducing higher quantities will increase the operating noise and may also influence temperature sending.
Others
Anti corrosion treated heat exchangers
To achieve increased durability by improved resistance to salt corrosion and atmospheric pollution, coated Anti corrosion treated heat exchangers (with special acryl pretreatment) are used for the heat exchanger of the outdoor unit.
In high corrosive areas, regular maintenance needs to be carried out.
SPECIFICATIONS
CEILING MOUNTED CASSETTE TYPE
Indoor unit
71
FCQ71LUV1
Model
Name
Outdoor unit
RR71MV1
Power supply
Cooling capacity 1
Power consumption
Indoor unit
Colour
Cooling 1
Unit
Decoration panel
Airflow rate (H/L)
Sound level (H/L) 2
Dimensions
(H X W X D)
Machine weight
Certified Operation range
Unit
Decoration panel
Unit
Decoration panel
Cooling
Outdoor unit
Piping connections
Colour
Compressor Type
Motor output
Refrigerant charge (R-410A)
Sound level 2 Cooling
Dimensions (H X W X D)
Machine weight
Certified Operation range Cooling
Liquid (Flare)
Gas (Flare)
Drain Indoor unit
Outdoor unit
Max. interunit piping length
Max. installation level difference
Heat insulation kW kW kW kg dB(A) mm kg
°CDB mm mm mm mm m m m 3 /min cfm dB(A) mm mm kg kg
°CWB
V1
Y1
RR71MY1
1 Phase, 220–230 V, 50 Hz
3 Phase, 380–415 V, 50 Hz
7.7
2.72(V1), 2.66(Y1)
21/13.5
741/477
35/28
256 X 840 X 840
21
2.2
2.7 (Charged for 30 m)
50
770
X
900
X
320
83(V1), 81(Y1)
100
FCQ100LUV1
RR100MY1
125
FCQ125LUV1
RR125MY1
3 Phase, 380–415 V, 50 Hz
10.5
3.60
12.8
4.66
----------
Fresh white
32/20
1,129/706
43/32 44/34
298 X 840 X 840
50 X 950 X 950
24
5.5
12 to 25
3.0
Ivory white
Hermetically sealed scroll type
3.75
3.7 (Charged for 30 m)
53
1,170
X
900
X
320
99
-15 to 46 o/9.5
o/15.9
VP25 (O.D o/32 X I.D o/25) o/26.0 (Hole)
70 (Equivalent length 90m)
30
Both liquid and gas piping
106
33/22.5
1,164/794
Note :
1 Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal).
2 Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
140
FCQ140LUV1
RR140MY1
14.2
5.02
44/36
14 to 25
2.84
4.3 (Charged for 30 m)
54
1,345
X
900
X
320
108
-5 to 46
CEILING SUSPENDED TYPE
Indoor unit
71
FHQ71BVV1B
100
FHQ100BVV1B
125
FHQ125BVV1B
Model
Name
RR71MV1
Outdoor unit RR100MY1 RR125MY1
RR71MY1
Power supply
Cooling capacity
Power consumption
Indoor unit
Outdoor unit
1
Colour
Airflow rate (H/L)
Sound level (H/L) 2
Dimensions (H X W X D)
Machine weight
Certified operation range
Colour
Compressor Type
Motor output
Refrigerant charge (R-410A)
Sound level 2
Dimensions (H X W X D)
Machine weight
Certified operation range
Piping connections
Liquid (Flare)
Gas (Flare)
Drain Indoor unit
Outdoor unit
Max. interunit piping length
Max. installation level difference
Heat insulation m kW kW
3 /min cfm dB(A) mm kg
°CWB kW kg dB(A) mm kg
°CDB mm mm mm mm m m
V1
Y1
1 Phase, 220–230 V, 50 Hz
3 Phase, 380–415 V, 50 Hz
195 X
770 X
7.1
2.75(V1), 2.70(Y1)
17/14
600/494
39/35
1,160
27
2.2
50
900
X
X
680
2.7 (Charged for 30 m)
320
83(V1), 81(Y1)
3 Phase, 380–415 V, 50 Hz
9.8
3.53
White
24/20
847/706
42/37
195 X 1,400 X 680
32
12 to 25
Ivory white
Hermetically sealed scroll type
3.0
3.7 (Charged for 30 m)
53
1,170 X 900 X 320
99
-15 to 46 o/9.5
o/15.9
VP20 (O.D o/26
X
I.D o/20) o/26.0 (Hole)
70 (Equivalent length 90m)
30
Both liquid and gas piping
12.2
4.51
30/25
1,059/883
44/39
195 X 1,590 X 680
35
3.75
106
Note :
1
2
Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal).
Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
20
21
SPECIFICATIONS
WALL MOUNTED TYPE
Indoor unit
71
FAQ71BVV1B
100
FAQ100CVEA
Model
Name
RR71MV1
Outdoor unit RR100MY1
Power supply
Cooling capacity
Power consumption
Colour
Indoor unit
Outdoor unit
1
Cooling
Airflow rate (H/M/L)
Sound level (H/M/L)
Dimensions (H
X
W
X
D)
Machine weight
Max. installation level difference
Heat insulation
1
2
Certified Operation range
Colour
Compressor Type
Motor output
Refrigerant charge (R-410A)
Sound level 2 Cooling
Piping connections
Dimensions (H X W X D)
Machine weight
Certified Operation range
Liquid (Flare)
Gas (Flare)
Drain Indoor unit
Outdoor unit
Max. interunit piping length m kW kW
3 /min cfm dB(A) mm kg
°CWB kW kg dB(A) mm kg
°CDB mm mm mm mm m m
V1
Y1
RR71MY1
1 Phase, 220–230 V, 50 Hz
3 Phase, 380–415 V, 50 Hz
7.6
2.93
(V1), 2.87(Y1)
White
19/-/15
671/-/530
43/-/37
290 X 1,050 X 230
13
12 to 25
Ivory white
Hermetically sealed scroll type
2.2
2.7 (Charged for 30 m)
50
770
X
900
X
320
83(V1), 81(Y1)
-15 to 46 o/9.5
o/15.9
VP13 (O.D o/18 X I.D o/13) o/26.0 (Hole)
70 (Equivalent length 90m)
30
Both liquid and gas piping
3 Phase, 380–415 V, 50 Hz
10.0
3.72
Fresh white
26/23/19
918/812/671
49/45/41
340 X 1,200 X 240
17
3.0
3.7 (Charged for 30 m)
1,170
X
53
900
99
X
320
Note :
1 Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal).
2
Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
71 100
Indoor unit FBQ71DV1 FBQ100DV1
125
FBQ125DV1
140
FBQ140DV1
Model
Name
RR71MV1
Outdoor unit RR100MY1 RR125MY1 RR140MY1
RR71MY1
Indoor unit 1 Phase, 220–240 V, 50 Hz
Power supply
Outdoor unit
Cooling capacity 1
Power consumption
Indoor unit
Cooling
Colour
Fan Airflow rate Cooling
(H/L)
External static pressure 2
Sound level 3 Cooling (H/L)
Outdoor unit
Dimensions (H X W X D)
Machine weight
Certified Operation range Cooling
Colour
Compressor Type
Motor output
Refrigerant charge (R-410A)
Sound level 3 Cooling
Piping connections
Dimensions (H X W X D)
Machine weight
Certified Operation range
Liquid (Flare)
Cooling
Gas (Flare)
Drain Indoor unit
Outdoor unit
Max. interunit piping length
Max. installation level difference
Heat insulation kW kW m 3 /min cfm
Pa dB(A) mm kg
°CWB kW kg dB(A) mm kg
°CDB mm mm mm mm m m
V1
Y1
1 Phase, 220–230 V, 50 Hz
3 Phase, 380–415 V, 50 Hz
7.1
2.85
(V1), 2.80(Y1)
18/15
635/530
37/32
300 X 1,000 X 700
36
2.2
2.7 (Charged for 30 m)
50
770 X 900 X 320
83(V1) 81(Y1)
10.0
3.70
32/23
1,130/812
----------
3 Phase, 380–415 V, 50 Hz
12.2
4.76
50-200
38/33
300 X 1,400 X 700
46
12 to 25
3.0
Ivory white
Hermetically sealed scroll type
3.75
3.7 (Charged for 30 m)
99
-15 to 46
53
1,170 X 900 X 320 o/9.5
o/15.9
VP25 (O.D o/32 X I.D o/25) o/26 (Hole)
70 (Equivalent length 90m)
30
Both liquid and gas piping
106
39/28
1,377/988
40/36
Note :
1
Rated cooling capacities are based on the following conditions: Suction temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal)
2
Initial setting is standard.
3 Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
14.1
5.07
14 to 25
3.0
4.3 (Charged for 30 m)
54
1,345 X 900 X 320
108
-5 to 46
OPTIONS
Indoor unit
CEILING MOUNTED CASSETTE TYPE
Name of option Remark
FCQ71LUV1
Decoration panel
Sealing material of air discharge outlet
Panel spacer
Fresh air intake kit 1
Chamber type
Direct installation type
Chamber connection kit 2
Insulation kit for high humidity
Without the T-joint pipe and fan
With the T-joint pipe, without fan
High-efficiency filter
Replacement high-efficiency filter
(Colorimetric method 65%)
(Colorimetric method 90%)
(Colorimetric method 65%)
(Colorimetric method 90%)
Filter chamber
Replacement long-life filter
Ultra long-life filter
Replacement ultra long-life filter
Branch duct chamber
Remote controller
Wired LCD remote controller with weekly schedule timer 3
Navigation Remote Controller Wired type 3
Central remote controller 4
Unified ON/OFF controller 4
Wired type 3
Wireless type
Schedule timer 4
Touch Controller 4
Adaptor for wiring 5
Wiring adaptor for electrical appendices 5
Installation box for adaptor PCB
Remote sensor (for indoor temperature)
Cooling only
KDTP55K80
KAFP556B80
KAFP557B80
KAFP552B80
KAFP553B80
KDJP55B80
Note: 1 Refer to page 6 for the details.
2 Required for installing high-efficiency filter or ultra long-life filter.
3 Wiring for wired remote controller to be procured locally.
4
The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
5
Installation box for adaptor PCB (KRP1H98) is necessary.
FCQ100LUV1
Kit name
FCQ125LUV1
BYCP125K-W1
KDBH55K160F
KDBP55H160FA
KDDP55B160
KDDP55B160K
KDDP55X160
KKSJ55KA160
KDTP55K160
KAFP556B160
KAFP557B160
KAFP552B160
KAFP553B160
KDDFP55B160
KAFP551K160
KAFP55B160
KAFP55H160H
KDJP55B160
BRC1C61
BRC7F633F
BRC1D61
BRC1E62
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
KRP1C63
KRP4AA53
KRP1H98
KRCS01-4B
FCQ140LUV1
Round flow type: List of optional parts required to achieve different flow patterns
For each flow pattern – all round, 4-way, 3-way, 2-way, branch duct connection – the compatibility of each independently installed option
(shown in the column on the left) to accessory options (listed across the top of each table) is shown in the cells where the relevant row and column intersect.
A circle ( o ) indicates compatibility, and a cross ( x
) indicates incompatibility. Any options not shown below are not suitable for independent or accessory installation.
All round flow 4-way flow
Optional accessory parts
Independently installable optional parts
Panel/grille related Panel spacer 1
Operation control related
Auxillary function related
Wireless remote controller
Fresh air intake kit (Chamber type) 1,2
Filter related
Fresh air intake kit (direct mount)
High-humidity operation kit
High-efficiency filter 2
Ultra-long-life filter 2
Panel spacer 1 o o o x o o
Wireless remote controller o
Fresh air intake kit
(Chamber type) 1,2 o o o o o o o x x o o
Fresh air intake kit
(direct mount) o o x o o o
High-humidity operation kit x o x o x x
High-efficiency
filter 2 o o o o x x
Ultra-long-life filter 2 o o o o x x
3-way flow 2-way flow
Optional accessory parts
Independently installable optional parts
Panel/grille related Panel spacer 1
Operation control related
Auxillary function related
Wireless remote controller
Fresh air intake kit (Chamber type) 1,2
Filter related
Fresh air intake kit (direct mount)
High-humidity operation kit
Ultra-long-life filter 2
Panel spacer 1
o
o
o x
o
3
3
3
3
Wireless remote controller
o
3
Fresh air intake kit
(Chamber type)
1,2
o
3 o o o o o x x o
Fresh air intake kit
(direct mount)
o
3 o x o o
High-humidity operation kit x o x o x
High-efficiency
filter
2 x x x x x x
Ultra-long-life filter
2
o
3 o o o x
Branch duct connection
Optional accessory parts
Independently installable optional parts
Branch duct 1
(Chamber type)
(Round duct type)
1-way branch / unit 3-way flow
2-way branch / unit 2-way flow
1-way branch / unit 2-way flow
Panel spacer 1 o x x
Wireless remote controller o o o
Fresh air intake kit
(Chamber type) 1,2
o
o
o
Fresh air intake kit
(direct mount) o
4 o
4 o
4
High-humidity operation kit x x x
High-efficiency
filter 2 x x x
Ultra-long-life filter 2 o o o
1
In some cases, depending on how the unit is embedded in the ceiling, use of branch ducts and fresh air intake kits may not be possible. Before starting installation work make sure to check whether or not joint installation is possible. In particular, ensure that the lower fixing position caused by the addition of panel spacers is acceptable.
2
Use a chamber connection kit if two different types of optional chamber are used together. In this case, the fresh air intake kit must be installed in the upper position.
3
It is not possible to use panel spacers in a 2-way flow installation.
4
It is not possible to install a branch duct on the same side to which a fresh air intake kit (direct mount) is installed.
22
OPTIONS
Indoor unit
CEILING SUSPENDED TYPE
Name of option Remark
Replacement long-life filter
Drain-up kit
L-type piping kit (for upward direction)
Remote controller
Resin net
Wired type 1
Wireless type
Wired LCD remote controller with weekly schedule timer 1
Navigation Remote Controller Wired type 1
Central remote controller 2
Unified ON/OFF controller 2
Schedule timer 2
Touch Controller 2
Adaptor for wiring
Wiring adaptor for electrical appendices 3
Interface adaptor for SkyAir series
Installation box for adaptor PCB
Remote sensor (for indoor temperature)
Electrical box with earth terminal (3 blocks)
Electrical box with earth terminal (2 blocks)
Note: 1
Wiring for wired remote controller to be procured locally.
2 This optional accessory requires DTA112BA51.
3 Installation box for adaptor PCB (KRP1CA93) is necessary.
Cooling only
FHQ71BVV1B
KAF501DA80
WALL MOUNTED TYPE
Name of option Remark
FAQ71BVV1B
Drain-up kit
Remote controller Wired type 1
Wireless type
Wired LCD remote controller with weekly schedule timer 1
Navigation Remote Controller
Remote sensor (for Indoor temperature)
Wired type 1
Central remote controller 2
Unified ON/OFF controller 2
Schedule timer 2
Touch Controller 2
Wiring adaptor for electrical appendices 3
Installation box for adaptor PCB
Cooling only
Electrical box with earth terminal (3 blocks)
Electrical box with earth terminal (2 blocks)
Noise filter ( For electromagnetic interface use only)
Note: 1 Wiring for wired remote controller to be procured locally.
2 The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
3 Installation box for adaptor PCB (KRP4AA93) is necessary.
BRC7EA619
KRCS01-1B
Kit name
FHQ100BVV1B
KAF501DA112
KDU50N125VE
KHFP5MA160
BRC1C61
BRC7EA66
BRC1D61
BRC1E62
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
KRP1BA54
KRP4AA52
DTA112BA51
KRP1CA93
KRCS01-1B
KJB311AA
KJB212AA
Kit name
K-KDU572EVE
BRC1C61
BRC1D61
BRC1E62
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
KRP4AA51
KRP4AA93
KJB311AA
KJB212AA
KEK26-1A
FHQ125BVV1B
KAF501DA160
FAQ100CVEA
BRC7EB519
KRCS01-4B
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
Name of option
High-efficiency filter 1
Remark
(Colorimetric method 65%)
(Colorimetric method 90%)
FBQ71DV1
KAF372AA80
KAF373AA80
KDDF37AA80
FBQ100DV1
Kit name
FBQ125DV1
KAF372AA160
KAF373AA160
KDDF37AA160 Filter chamber
Replacement long-life filter
Replacement long-life filter chamber kit
Service panel
Air discharge adaptor
Remote controller Wired type 2
Wireless type
Wired LCD remote controller with weekly schedule timer 2
Navigation Remote Controller Wired type 2
Adaptor for wiring (interlock for fresh air intake fan)
Wiring adaptor for electrical appendices
Cooling only
KAF371AA80
KAF375AA80
KTB25KA80W
KTBJ25K80F
KTBJ25K80T
KDAJ25K71A
BRC1C61
BRC4C64
BRC1D61
BRC1E62
KRP1C64
KAF371AA160
KAF375AA160
KTB25KA160W
KTBJ25K160F
KTBJ25K160T
KDAJ25K140A
KRP4AA51
KRCS01-4B Remote sensor
Mounting plate for adaptor PCB.
3
Central remote controller 4
Unified ON/OFF controller 4
Schedule timer 4 DST301BA61
DCS601C51 Touch Controller 4
Note:
1
2
If installing a high efficiency filter on the unit, an assembly chamber for either bottom or rear suction is required.
Wiring for wired remote controller to be procured locally.
3 Mounting plate for adaptor PCB is necessary for each adaptor marked .
4 The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
5
Up to 2 adaptors can be fixed for each mounting plate.
6
Only one mounting plate can be installed for each indoor unit.
KRP4A96 5,6
DCS302CA61
DCS301BA61
FBQ140DV1
23
Outdoor unit
Name of option
Central drain plug
RR71MV1/Y1
Kit name
RR100MY1
KKPJ5F180
RR125MY1 RR140MY1
DIMENSIONS
(Unit: mm)
CEILING MOUNTED CASSETTE TYPE
[FCQ71-140LUV1]
9
B
300 or less
860~910(Ceiling opening space) (Note 4)
710(Hanging bolt pitch)
420
55
[FCQ71-140LUV1]
950
81
[FCQ71LUV1]
2x100=200
124
C/L
85
Connection position of branch duct
(round shape type)
16-M4 Hole
8
Piping Connection
Side
Note 2
C
157
350
B arrow view
Connection position of branch duct
(square-shaped type)
6
420
[FCQ71LUV1]
840
340
80 2x100=200 80
124
16-M4 Prepared hole
55
Connection position of branch duct
(square-shaped type)
Drain Connection
Side
A arrow view
7
[FCQ71LUV1]
3
55
64
50
81
840
2x100=200
124
85
55
27-M4 Prepared hole
5
Connection position of branch duct
(square-shaped type)
20-M4
Prepared hole
[FCQ71LUV1]
160
124
109
95
C/L
Hanging bolt
4-M8~M10
Connection position of branch duct
(round shape type)
20
350
C/L
157
280
330
4 1 2
35 or less
(Note 4)
Connection position of branch duct
(round shape type)
256
157
350
A
35 or less
(Note 4)
Connection position of branch duct
(square-shaped type)
[FCQ100-140LUV1]
81 2x100=200 85
160
C/L
Connection position of branch duct
(round shape type)
16-M4 Hole
157
350
B arrow view
Connection position of branch duct
(square-shaped type)
20-M4
Connection position of branch duct
(square-shaped type)
[FCQ100-140LUV1]
160
167
93 67
95
29
Prepared hole
C/L
Connection position of branch duct
(round shape type)
Connection position of fresh air intake kit
(direct installation type)
90
183
C arrow view
ø100
(knock
hole)
Connection position of branch duct
(round shape type)
Connection position of fresh air intake kit
(direct installation type)
ø100
(knock
hole)
90
196
C arrow view
55
Hanging bolt
4-M8~M10
Connection position of branch duct
(round shape type)
[FCQ100-140LUV1]
340
80
840
2x100=200
160
20
350
C/L
157
80
280
330
16-M4 Prepared hole
55
Connection position of branch duct
(square-shaped type)
4 1 2
35 or less
(Note 4)
Connection position of branch duct
3
(round shape type)
55
[FCQ100-140LUV1]
64
50
81 2x100=200
160
256
840
157
350
A
85
55
27-M4 Prepared hole of branch duct
5
35 or less
(Note 4)
Connection position
(square-shaped type)
Notes:
1
Sticking location for manufacture's label
manufacture's label for indoor unit:
Suction grille inner side's electric components box's lid surface
manufacture's label for decoration panel :
Decoration panel's corner decoration cover inner surface
2 In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller in detail.
3 When the temperature and humidity in the ceiling exceed 30˚C and RH 80% or the fresh air is inducted into the ceiling or the unit continues 24 hour operation, an additional insulation (thickness 10mm or more of glasswool or polyethylene form) is required.
4
Though the installation is acceptable up to maximum of 910mm square ceiling opening, keep the clearance of 35mm or less between the indoor unit and the ceiling opening so that
the panel overlap allowance can be ensured.
5
Please do not place the thing been damp and troubled under an indoor unit.
When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
Required space
200mm or more
1500mm or more
1500mm
or more
1500mm
or more
200mm or more 1500mm or more
The necessary space is 500mm or more when the air-outlet is blocked with the accessory.
Moreover when the corner areas are blocked
(both right and left of the blocked air outlet), the necessary space is 200mm or more.
1
2
3
4
5
Liquid piping connection
Gas piping connection
Drain piping connection
Transmission wiring connection
8
9
6
7
Remote controller wiring connection
Air-outlet
Suction grille
Corner decoration cover
Drain hose (accessory)
24
DIMENSIONS
(Unit: mm)
CEILING SUSPENDED TYPE
FHQ71BVV1B
FHQ100BVV1B
FHQ125BVV1B
A
1120
1360
1550
B
1160
1400
1590
18 17 16
170
142
105
90
58
12 9
145 60
127
40 50
60 65
Position slit hole for taking out in piping back
(View from the front)
10
8
105
15
A
(Hanging position)
680
Hanging bolt
4-M8~M10
1
5 11 80
Position : Hole of wall for taking out in piping back
(View from the front)
13
55
6
Obstacle
Floor side
30 or more
(Service space)
Drain piping connection VP20
(For left piping)
B
The Front
80
3 2
Notes:
1
Location of unit's Name Plate: Bottom of fan housing inside the suction grille.
2
In case of using wireless remote controller, this position will be a signal receiver.
Refer to the drawing of wireless remote controller in detail.
3
(Applies to FHQ35-71BV only)
The remote control code is the standard <about 3 m outside the machine> attached.
(0.5 mm 2 2 wicks O.D. 5.4)
(It is not attached to VRV.)
7 5
80
105
170
30 or more
(Service space)
Brand name plate
(Note.2)
6
4
4 o/ 45
55 14
1
2
3
4
5
Air discharge grille
Air suction grille
Air filter
Gas piping connection
6
7
Liquid piping connection
Drain piping connection
Earth terminal (inside the electric components box) (M4) (Applies to FHQ35-71BV)
Earth terminal (inside the control box) (M4)
(Applies to FHQ100P/125P)
8
9
10
11
12
13
Suspension bracket
Backward piping and wiring connection opening lid
Upward piping and wiring connection opening lid
Right side piping connection
14
15
16
17
Left back drain piping connection
Left side drain piping connection
Right side drain piping connection
Hole of wall for taking out in piping back
Upward drain piping connection
Upward gas piping connection
18 Upward liquid piping connection
WALL MOUNTED TYPE
[FAQ71BVV1B]
Piping direction
Approx.400
232
230
7
25
Dimensions for full open front panel
9 2 1
50 or more
(Required space)
Piping direction
104
Outside line
1
Notes:
Location of unit's of name Plate:
Right side surface of casing
2
In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller in detail.
80 hole
60
6
5
4
Mounting location
3
Name plate Note)2
1050
894
Piping direction
52
50 or more
(Required space)
2500
For in or more installation high spaces
120 or less
Approx.345
Approx.390
Approx.475
98
80 hole
Piping
Wiring and intake
4
5
1
2
Front panel
3
Front grille
Air outlet
6
7
8
9
Gas piping
Liquid piping
Drain hose
Earth terminal
Right side piping connection hole
Left side piping connection hole
8
WALL MOUNTED TYPE
[FAQ100CVEA]
Piping direction
242
Approx.440
240
7
9
Dimensions for full open front panel
2
1
50 or more
(Requred space)
Piping direction
79.5
Outside line
φ80 hole
1200
3
Name plate Note)2 Piping direction
50 or more
(Requred space)
2500 or more
For installation in high spaces
1085 35.5
φ80 hole
Piping and
Wiring intake
120 or less
8
65
6
Approx.400
89
Mounting location
5
4
Approx.460
Approx.465
Notes:
1
Location of unit's of Name Plate:Right side surface of casing
2 In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote contorller in detail.
3
Please do not place the thing been damp and troubled under an indoor unit. when the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
[FBQ71DV1]
30- 4.7 Hole
(All around)
8
27 631
(Hanging bolt pitch)
10
30- 4.7 Hole
(All around)
CASE 1)
Control box
Air outlet Air inlet
9
Inspection hatch 450 or more
167
700 or more
(Service space)
2
6
Air outlet
3
1 5
Air inlet
(Note.2)
1
2
3
4
5
6
Front panel
Front grill
Air outlet
Gas piping
7
8
Liquid piping
Drain hose
Earth terminal
Right side piping connection hole
9 Left side piping connection hole
Inspection hatch 1
(450mmX450mm)
Control box
300 or less
12
435
16-8X12 oblong hole
(All around)
Inspection hatch Ceiling
Air outlet
Unit base
Fig.A
Air inlet
5X150=750
760
785
View
(From the Air outlet)
513
18-8X12 oblong hole
(All around)
49
CASE 2),3)
Control box
Inspection hatch 1
(450mmX450mm)
Control box
Inspection hatch 3
(SAME AS THE INDOOR
UNIT SIZE +300 OR MORE)
Control box
B
Inspection hatch Ceiling
Inspection hatch 2
(SAME AS THE INDOOR
UNIT SIZE OR MORE)
700 or more
View B-1
700 or more
View B-2
169
290
11
28
7 4 6X150=900
700
925
950
Ceiling
Notes:
1
Location of MANUFACTURE'S LABEL: Contro box surface
Floor surface
(From the Air inlet)
2 Mount the air filter at the suction side. (Select its colorimethod (gravity method) 50% or more.)
3 Do not locate things should not be wet under the indoor unit. Dews may drop when humidity reaches over 80%,or a drain gets stuck,or air filters are not clean.
4
Space for Service Works
According to any one of below 1)~3),secure a space for service works,such as,checking and maintenance of control box,etc.
1)One inspection hatch (450X450) on the control box side and a space of 300mm or more under the unit.(Fig.A)
2)One inspection hatch (450X450) on the control box side and 2 (two) inspection hatches under the unit.(Arrow View B-1)
3)3 (three) inspection hatches under the unit and the control box.(Arrow View B-2)
1
2
3
4
Liquid piping connection
Gas piping connection
Drain piping connection
Earth terminal
(Terminal in Control box)
5
6
7
Control box(Inside)
Remote control wiring connection
Power supply wiring and a
8
9
10 transmission wiring
Air discharge flange
Air suction flange
Hanger
11 Socket (for maintenance)
12 Drain hose(Accessory)
26
DIMENSIONS
(Unit: mm)
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
[FBQ100DV1, 125DV1, 140DV1]
40- 4.7 Hole
(All around)
27 631
(Hanging bolt pitch)
8
10
48- 4.7 Hole
(All around)
CASE 1)
Control box
Inspection hatch 1
(450mmX450mm)
Control box
Air outlet
Inspection hatch 450 or more
700 or more
(Service space)
Air outlet
167
3
1 2
6
5
Air inlet
9
Air inlet
(Note.2)
169
290
11
28
7 4 8X150=1200
700
1325
1350
Ceiling
Floor surface
Notes:
1
2
Location of MANUFACTURE'S LABEL: Control box surface
Mount the air filter at the suction side.(Select its colorimethod (gravity method) 50% or more.
(From the Air inlet)
3 Do not locate things should not be wet under the indoor unit.Dews may drop when humidity reaches over 80%,or a drain gets stuck,or air filters are not clean.
4 Space for Service Works
According to any one of below 1)~3),secure a space for service works,such as,checking and maintenance of control box,etc.
1)One inspection hatch (450X450) on the control box side and a space of 300mm or more under the unit.(Fig.A)
2)One inspection hatch (450X450) on the control box side and 2 (two) inspection hatches under the unit.(Arrow View B-1)
3)3 (three) inspection hatches under the unit and the control box.(Arrow View B-2)
Inspection hatch
Ceiling
Air outlet
Unit base
Fig.A
Air inlet
300 or less
12
635
(SAME AS THE INDOOR
UNIT SIZE OR MORE)
20-8X12 oblong hole
(All around)
7X150=1050
1160
1185
View
(From the Air outlet)
713
49
20-8X12 oblong hole
(All around)
CASE 2),3)
Control box
Inspection hatch 1
(450mmX450mm)
Control box
Inspection hatch 3
(SAME AS THE
INDOOR UNIT
SIZE +300 OR
MORE)
Control box
Inspection hatch
B
Ceiling
Inspection hatch 2
(SAME AS THE
INDOOR UNIT
SIZE OR MORE)
700 or more
View B-1
700 or more
View B-2
5
6
3
4
1
2
Liquid pip ing connection
Gas pip ing connection
Drain pip ing connection
Earth terminal
(Terminal in Control box)
7
Control box(Inside)
Remote control wiring connection
Power supply wiring and a
8
9 transmission wiring
Air discharge flange
Air suction flange
Hanger 10
11
12
Socket(For maintenance)
Drain hose(Accessory)
27
OUTDOOR UNIT // RR71MV1/Y1
Hole for anchor bolt 4-M12
30
140 620
900
89
140
36
3
4
2
1
7
6
5
8
89
142
71
19
16
5
45 376 191
19 80
145
6
7
5
52
13 67
1
2
Gas piping connection
Liquid piping connection
3
4
5
Service port (in the unit)
Earth terminal
Refrigerant piping intake
6
7
8
Power supply wiring intake
Transmission wiring intake
Drain piping connection
OUTDOOR UNIT // RR100MY1
Hole for anchor bolt 4-M12
30
140 620
900
89
140
36
2
1
7
3
4
6
5
5
45 376 191
8
89
142
19
71 16
5
19 80
145
7
6
7
6
5
52
13 67
1
2
Gas piping connection
Liquid piping connection
3
4
5
Service port (in the unit)
Earth terminal
Refrigerant piping intake
6
7
8
Power supply wiring intake
Transmission wiring intake
Drain piping connection
28
DIMENSIONS
(Unit: mm)
OUTDOOR UNIT // RR125MY1
Hole for anchor bolt 4-M12
30
140 620
900
89
140
36
3
4
2
1
7
6
5
5
45
OUTDOOR UNIT // RR140MY1
Hole for anchor bolt 4-M12
376 191
8
89
142
19
71 16
5
19 80
145
7
6
7
6
5
52
13 67
1
2
Gas piping connection
Liquid piping connection
5
6
3
4
Service port (in the unit)
Earth terminal
Refrigerant piping intake
Power supply wiring intake
7
8
Transmission wiring intake
Drain piping connection
30
140 620
(Pitch of foundation bolt holes)
900
140
38
91
1
7
6
5
4
2
3
5
7
6
7
6
5
8
71
89
142
19
16
5
45 376 191
19 80
145
52
13 67
4
5
6
1
2
3
Gas piping connection
Liquid piping connection
Service port
Earth terminal
Refrigerant piping intake
Power supply wiring intake
7
8
Transmission wiring intake
Drain piping connection
29
REMOTE CONTROLLER
Wireless type
• Remote controller dimensions
Transmitting part
CEILING MOUNTED CASSETTE TYPE <Round Flow>
• Receiver installation procedure
Receiver
Refrigerant piping side
CEILING SUSPENDED TYPE
• Receiver installation procedure
The Front Receiver
62 17.5
• Remote controller holder installation procedure
<installation to wall surface>
Liquid crystal remote controller
(wireless)
Remote controller holder
Drain piping side
• Receiver detail Decoration panel
• Receiver
detail
WALL MOUNTED TYPE
• Receiver installation procedure
FAQ71BVV1B
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
• Receiver detail
2-5 x 9 Slot
• Receiver
detail
Receiver
FAQ100CVEA Receiver
70 18
0.5
35
49
(Ceiling opening)
Switch box
(field Supplied parts)
Service space for ceiling installation
Note :
Do not install more than 3 receivers in the vicinity of one another.
With 4 or more units, there is always the possibility of malfunction
• Receiver
detail
Wired type
BRC1D61 / BRC1C61
• Remote controller dimensions
120 17
18
23 28
46
Cord outlet hole
• Installation method
A Exposed body, exposed cord
Staple
Remote controller
B Exposed body, embedded cord
17 Conduit
Remote controller
C Exposed body, embedded code
Remote controller
17
0~5
(Between remote
controller and
control box)
Control box
Specifications of cord
Type
Size
Total length
Shield wire (insulated thickness: 1 mm or more)
0.75~1.25 mm
500 m
2
17
Through hole
( 12- 16)
Note)
1. Remote controller cord and staple are not attached.
They are field supplied parts.
BRC1E62
Upper case Lower case
120
Operation lamp
(Green)
19
5 X 7 oblong hole
23
46
28
48.5
Code outlet hole
5 X 15 oblong hole
• Installation method
A Exposed cord
Top left outlet
Top center outlet
Staple
B Embedded cord
19
C Embedded cord
(use switch box)
Condit
19
Left outlet
19
Specifications of cord
48.5
Lower case portion
Note)2
Through hole
( 8- 10)
28
46
Switch box for one switch ex.) KJB111A
(optional accessory)
Switch box for two switch ex.) KJB211A
(optional accessory)
Lower case portion
0~5
(Between remote controller and control box)
Switch box
[field supplied part]
Note)
1. Remote controller cord and staple are not attached. They are field supplied parts.
2.If the hole size is too large or the location is not proper, the hole may come out from the remote controller.
Type
Size
Total length
Vinyl cord with sheath or cable (insulated thickness: 1mm or more)
0.75~1.25 mm 2
500 m
30
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project