- Computers & electronics
- Computers
- Server barebones
- Connect Tech
- Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
- User manual
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board User manual
Add to My manuals29 Pages
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board is a powerful and versatile embedded computing solution designed for a wide range of industrial and commercial applications. With its support for high-performance Qseven modules, flexible I/O options, and rugged construction, it provides a reliable and scalable platform for demanding embedded systems.
advertisement
![Connect Tech Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board User manual | Manualzz Connect Tech Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board User manual | Manualzz](http://s1.manualzz.com/store/data/001468030_1-270903f9053b8084657dc63b02b633fb-360x466.png)
Xtreme/SBC PCI-104 Single Board Computer
& PCI-104 Qseven Carrier Board
User Manual
Connect Tech Inc.
42 Arrow Road
Guelph, Ontario
N1K 1S6
Tel:
519-836-1291
Toll:
800-426-8979 (North America only)
Fax:
519-836-4878
Email:
[email protected] [email protected]
Web:
www.connecttech.com
CTIM-00060 Revision 0.03 February 22, 2013
1
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Table of Contents
2 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Revision 0.03 3
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Customer Support Overview
If you experience difficulties after reading the manual and/or using the product, contact the
Connect Tech reseller from which you purchased the product. In most cases the reseller can help you with product installation and difficulties.
In the event that the reseller is unable to resolve your problem, our highly qualified support staff can assist you. Our support section is available 24 hours a day, 7 days a week on our website at: www.connecttech.com/sub/support/support.asp.
See the contact information section below for more information on how to contact us directly. Our technical support is always free.
Contact Information
We offer three ways for you to contact us:
Mail/Courier
You may contact us by letter at:
Connect Tech Inc.
Technical Support
42 Arrow Road
Guelph, Ontario
Canada N1K 1S6
Email/Internet
You may contact us through the Internet. Our email and URL addresses on the Internet are: [email protected] [email protected] www.connecttech.com
Note:
Please go to the
Download Zone
or the
Knowledge Database
in the
Support Center
on the Connect
Tech website for product manuals, installation guides, device driver software and technical tips.
Submit your technical support questions to our customer support engineers via the
Support Center
on the Connect Tech website.
Telephone/Facsimile
Technical Support representatives are ready to answer your call Monday through Friday, from
8:30 a.m. to 5:00 p.m. Eastern Standard Time. Our numbers for calls are:
Toll Free
: 800-426-8979 (North America only)
Telephone
: 519-836-1291 (Live assistance available 8:30 a.m. to 5:00 p.m. EST,
Monday to Friday)
Facsimile
: 519-836-4878 (on-line 24 hours)
4 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Limited Lifetime Warranty
Connect Tech Inc. provides a Lifetime Warranty for all Connect Tech Inc. products. Should this product, in Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non-Connect Tech
Inc. authorized modification or repair.
You may obtain warranty service by delivering this product to an authorized Connect Tech Inc. business partner or to Connect Tech Inc. along with proof of purchase. Product returned to
Connect Tech Inc. must be pre-authorized by Connect Tech Inc. with an RMA (Return Material
Authorization) number marked on the outside of the package and sent prepaid, insured and packaged for safe shipment. Connect Tech Inc. will return this product by prepaid ground shipment service.
The Connect Tech Inc. Lifetime Warranty is defined as the serviceable life of the product. This is defined as the period during which all components are available. Should the product prove to be irreparable, Connect Tech Inc. reserves the right to substitute an equivalent product if available or to retract Lifetime Warranty if no replacement is available.
The above warranty is the only warranty authorized by Connect Tech Inc. Under no circumstances will Connect Tech Inc. be liable in any way for any damages, including any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use, such product.
Copyright Notice
The information contained in this document is subject to change without notice. Connect Tech
Inc. shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Connect Tech, Inc.
Copyright

1997 - 2011 by Connect Tech, Inc.
Trademark Acknowledgment
Connect Tech, Inc. acknowledges all trademarks, registered trademarks and/or copyrights referred to in this document as the property of their respective owners.
Not listing all possible trademarks or copyright acknowledgments does not constitute a lack of acknowledgment to the rightful owners of the trademarks and copyrights mentioned in this document.
Revision History
Revision 0.00 – January 10, 2011
Revision 0.01 – March 4, 2011
Revision 0.02 – May 31, 2012
Revision 0.03 – February 22, 2013
Revision 0.03 5
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Introduction
Xtreme/SBC PCI-104 Single Board Computer
Connect Tech’s Xtreme/SBC PCI-104 Single Board Computers offer a variety of embedded processor options including Intel Atom, Freescale i.MX51, TI OMAP and NVIDIA Tegra.
Xtreme/SBC solutions are modular and completely scalable, with access to current embedded processors that are easily upgradable to accommodate future generations of Intel Atom processors, such as Intel Atom E6xx, or ARM based processors, such as Cortex A8.
The on-board connectors of our Xtreme/SBC products provide access to SATA, USB, Ethernet,
LVDS and VGA Video, and RS-232 & RS-422/485.
To learn more about Connect Tech’s Xtreme/SBC PCI-104, visit http://www.connecttech.com/sbc.
PCI-104 Qseven Carrier Board
Connect Tech’s PCIe/104 Qseven Carrier Board solutions are small embedded carrier boards that allow complete integration with industry standard Qseven modules. Using any off-the-shelf
Qseven module provides a variety of embedded processor options including Intel Atom, Freescale i.MX51, TI OMAP and NVIDIA Tegra. This modular approach easily accommodates future generations of Intel Atom processors, such as Intel Atom E6xx, or ARM based processors, such as
Cortex A8. The on-board connectors of our Qseven products provide easy access to SATA, USB,
Ethernet, LVDS and VGA Video, and RS-232 & RS-422/485.
What is Qseven?
Qseven is an off-the-shelf, multi-vendor, Computer-on-Module that integrates the core components of a common PC, and mounts onto an application specific carrier board. Qseven modules have a standardized form factor of 70mm x 70mm and specify a PCIe style edge connector which interfaces to a low cost, high performance MXM socket on the carrier board.
This single ruggedized MXM connection provides all the Qseven interfaces including: graphics, audio, mass storage, network, and multiple USB ports.
To learn more about Connect Tech’s Xtreme/SBC PCI-104, visit http://www.
connecttech .com/qseven
Features
ï‚·
Qseven module carrier
ï‚·
PCI-104 form factor
ï‚·
Support for up to 4 PCI-104 Devices
ï‚·
Dual display, VGA (via SDVO) and 1x24 LVDS
ï‚·
2x SATA
ï‚·
2x RS232
ï‚·
2x RS485
ï‚·
1x 10/100/1000 Ethernet
ï‚·
ATX power input or +5V/+12V only operation
6 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
System Block Diagram
The Qseven module implements the core processing features including: processor, memory, and system physical interfaces via the southbridge.
Many of the Qseven modules are based on the mobile Intel Atom architecture (Z series processor + Poulsbo
/ SCH US15W chipset); shown in the block diagram below.
This document will generally refer to the features of the US15W.
Revision 0.03 7
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Hardware Description
Connector Locations
Xtreme/SBC PCI-104
– Top
Xtreme/SBC PCI-104
– Bottom
Connector Summary
Location
P1
P2
P3A, P3B
P4
P5
P6
P7
P8
P9
P10A, P10B
P11
P12
P13
P14
P16
Connection
Q7
PCI-104
USB
GBE
VGA
ATX Power
LVDS Video
LVDS Backlight
RS232 serial
SATA
RS485 serial
PCI-104
PS/2 Keyboard & Mouse
Fan Power
Battery holder
Jumper Summary
Jumper
J1
J2
J3
J4
J5
J6
J7
J8
J9
Function
PS/2 power
Fan Power
Fan PWM polarity
LVDS panel power
LVDS backlight enable polarity
LVDS Backlight
Power
Suspend Selection
Power Supply On
Power Button
8 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Qseven Module Interface
Description
The processor and Chipset are implemented on the Qseven CPU module, which connects to the
Xtreme/SBC PCI-104 via a MXM connector. As previously mentioned, many of the existing Qseven
Modules use the Intel Atom mobile architecture, Z series processor + Poulsbo / SCH US15W chipset. The
Xtreme/SBC PCI-104 implements a subset of the Qseven features, as describe in the introduction.
For a list of Qseven module vendors, visit http://www.qseven-standard.org/
Connector
Function Qseven interface
Location
P1
Type
MXM
Foxconn AS0B326-S78N-7F (or equivalent)
Pinout
Refer to Qseven specification
Graphics
The availability of the graphics interfaces depends on the Qseven module selected.
US15W:
The US15W chipset provides GMA 500 graphics sub-system and provides two display interfaces:
SDVO (serial digital video output) and LVDS (low voltage differential signalling). The resolution is generated by the by GMA 500 is limited 1280x1024.
The configuration of either interface as the primary or secondary display depends on the Qseven module’s
BIOS capabilities and settings. Refer to the Qseven module’s documentation for more details.
VGA
Description
The VGA interface is implemented using the Qseven SDVO interface, with a SDVO to VGA converter
(Chrontel CH7317B) which supports resolutions up to 1920x1200; however actually resolutions depend on the Qseven module.
Connector
Function VGA graphics
Location
P5
Type
2x5 2mm header
MLE TSHSM-205-D-06-G-V-L (or equivalent)
Pinout
Pin
1
3
5
7
9
Signal
DAC_RED
DAC_GREEN
DAC_BLUE
HSYNC
VSYNC
Pin
2
4
6
8
10
Signal
GND
N/C
SC_DDC
SD_DDC
GND
Revision 0.03 9
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
LVDS
Description
The Xtreme/SBC PCI-104 provides dual 18 or 24 bit LVDS display channels via P7, which are connected directly from the Qseven module . LVDS panel supply power is selected with jumper J4 and backlight power is selected with jumper J6. Both are current limited to 500 mA.
US15W:
The US15W provides only a single 18 or 24 bit display channel. Each LVDS data pair carries two bits, each channel has four data pairs.
Connectors & Jumpers
Function LVDS Graphics
Location
P7
Type
Hirose DF14-30P-1.25H connector
Pinout
12
13
14
15
7
8
9
10
11
Pin
1
2
3
4
5
6
Signal
VCC_PNL
VCC_PNL
GND
GND
LVDS_A3_N
LVDS_A3_P
LVDS_CLK_N
LVDS_ACLK_P
GND
LVDS_A2_N
LVDS_A2_P
LVDS_A1_N
LVDS_A1_P
LVDS_A0_N
LVDS_A0_P
Description
Panel Power
Panel Power
Digital ground
Digital ground
Channel A Data
Channel A Data
Channel A Clock
Channel A Clock
Digital ground
Channel A Data
Channel A Data
Channel A Data
Channel A Data
Channel A Data
Channel A Data
16
17
GND
LVDS_B3_N
18 LVDS_B3_P
19 LVDS_BCLK_N
20 LVDS_BCLK_P
21 GND
22 LVDS_B2_N
Digital ground
Channel B Data
Channel B Data
Channel B Clock
Channel B Clock
Digital ground
Channel B Data
23
24
25
26
LVDS_B2_P
LVDS_B1_N
LVDS_B1_P
LVDS_B0_N
Channel B Data
Channel B Data
Channel B Data
Channel B Data
27
28
LVDS_B0_P
GND
Channel B Data
Digital ground
29 LVDS_DID_CLK Display ID Clock
(3.3V)
30 LVDS_DID_DATA Display ID Data (3.3V)
10 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Function LVDS backlight power
Location
P8
Type
Hirose DF13-8P-1.25H connector
Pinout
Pin
1
2
3
4
5
6
7
8
Signal
+12V
+12V
+5V
+5V
LVDS_BLEN
VCC_BKL
GND
GND
Description
+12 V DC, max. 1A
+12 V DC, max. 1A
+5 V DC, max. 1A
+5 V DC, max. 1A
Backlight enable, level selected with J4
Back light power, selected with J6
Digital ground
Digital ground
Function LVDS backlight power select
Selects either +12V or +5V. Refer to the display panel’s documentation for proper configuration.
Location
J6
Type
1x3 0.100” jumper block
Pinout
Position
1-2
2-3 off
Description
+12V
+5V floating
Default
+12V
Function LVDS panel power select
Selects either +3.3V or +5V. Refer to the display documentation for proper configuration.
Location
J4
Type
1x3 0.100” jumper block
Pinout
Position
1-2
2-3 off
Description
+3.3V
+5V floating
Default
+3.3V
Revision 0.03 11
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Function LVDS backlight enable polarity
Selects either positive or negative. Refer to the inverter power supply documentation for proper configuration.
Location
J5
Type
1x2 2mm jumper block
Pinout
Position
off on
Description
Positive polarity
Negative polarity
Default
Positive polarity
12 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Gigabit Ethernet
Description
The gigabit Ethernet interface’s controller (MAC + PHY) is implemented on the Qseven module, while the
Xtreme/SBC PCI-104 provides the necessary magnetics and termination.
Most Qseven modules support 1000BASE-T, 100BASE-TX, and 10BASE-T standards with either a
Realtek 8111 or Intel 82574 PCIe Ethernet controller.
Connector & LEDs
Function Gigabit Ethernet
Location
P8
Type
2x5 2mm header
MLE TSHSM-205-D-06-G-V-L (or equivalent)
Pinout
Pin Signal Description Pin Signal Description
1
3
MX1-
MX2-
5 FGND
7
9
MX3-
MX4-
Data
Data
Frame
Ground
Data
Data
2
4
6
8
10
MX1+
MX2+
FGND
MX3+
MX4+
Data
Data
Frame
Ground
Data
Data
Function Ethernet Status LEDs
Locations
Pin Signal
D9 Activity
D10 1000BASE-T Link
D11 100BASE-TX Link
D12 10BASE-T Link
Revision 0.03 13
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
USB 2.0
Description
The Xtreme/SBC PCI-104 implements 4 of the 8 available USB 2.0 connections via two connectors. Over current protection and power supply filtering is provided.
Only the USB host features of the Qseven specification have been implemented, USB client features are not supported.
Connector
Function USB 2.0 x2
Locations
P3A, P3B
Type
Hirose DF13-8P
Pinout
Pin
4
5
6
7
8
1
2
3
Signal
VCC_USB_0
USB_0_N
USB_0_P
USB_GND_0
USB_GND_1
USB_1_N
USB_1_N
VCC_USB_1
Description
Port 0 Filtered +5V
Port 0 Data
Port 0 Data
Port 0 Filtered Digital Ground
Port 1 Filtered Digital Ground
Port 1 Data
Port 1 Data
Port 1 Filtered +5V
14 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
SATA
Description
The Xtreme/SBC PCI-104 provides 2 SATA host connections.
US15W:
Most Qseven modules based on the US15W, convert the US15W’s IDE interface to one SATA connection (as IDE master) and one built-in NAND based flash drive (as IDE slave). Consult the Qseven module’s documentation for more information.
In this case only P10A connector is active
Connector & LEDs
Function SATA host
Locations
P10A, P10B
Type
Industry standard right angle sata host connector
Molex 0470804005 (or equivalent)
Pinout
Pin
4
5
6
7
1
2
3
Signal
GND
SATA_TX_P
SATA_TX_N
GND
SATA_RX_N
SATA_RX_P
GND
Function SATA Status LEDs
Locations
Pin
D13
Signal
Activity
Revision 0.03 15
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
PCI-104
Description
The Xtreme/SBC PCI-104 allows up to 4 PCI-104 add-on boards to be installed in a “stack up” configuration. The PCI-104 connected through a PCIe to PCI bridge which is attached the first x1 PCIe lane of the Qseven connector.
Note: The Xtreme/SBC PCI-104 provides 3.3V generated from the +5V input power. The entire +3.3V rail on the PCI-104 stack is limited to 4A.
Connectors
Function PCI-104 (Top Stacking Only)
Locations
P2
Type
Industry standard
EPT 264-60303-02
(A1 @ Bottom Left Corner)
Pinout
16 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
LPC Super I/O
The Xtreme/SBC PCI-104 implements many low speed legacy I/O features with the SMSC SCH3114
Super I/O, which is connected to the Qseven module via the LPC (Low Pin Count) bus. This Super I/O device provides 4 serial ports, 2 PS/2, and many other status / control features.
Note: the Qseven specification states that all Qseven modules BIOS implementations must support either the Winbond W83627 or SMSC SCH3114.
Serial
Description
Two RS232 serial ports are provided on P9 and two RS485 serial ports are provided on P11.
For the RS485 ports, the default configuration is full duplex without any bias or termination. Various resistors configurations can be populated to enabled TX and RX termination as well as RTS control. The following diagram shows the available configuration options. Contact Connect Tech’s support department for further information.
Revision 0.03
Resistor
R99
R101
R156
R160
R98
R102
R100
R97
Function
Always enable driver
Always enable receiver
RTS controlled receiver
RTS controlled driver
Receiver termination
Driver termination
Receiver bias
Receiver bias
Default
Populated
Populated
17
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Connectors
Function RS232 x2
Locations
P9
Type
2x10 2mm header
Pinout
Pin
9
11
13
1
3
5
7
15
17
19
Signal
DCD1
RXD1
TXD1
DTR1
GND
DCD2
RXD2
TXD2
DTR2
GND
Function RS485 x2
Locations
P11
Type
2x10 2mm header
Pinout
Pin
9
11
13
15
1
3
5
7
17
19
Signal
RXD0+
TXD0+
TXD0-
RXD0-
GND
RXD1+
TXD1+
TXD1-
TXD1-
GND
Pin
10
12
14
2
4
6
8
16
18
20
Pin
10
12
14
16
2
4
6
8
18
20
Signal
DSR1
RTS1
CTS1
RI1
N/C
DSR2
RTS2
CTS2
RI2
N/C
Signal
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
18 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
PS/2 Keyboard and Mouse
Description
A PS/2 keyboard and PS/2 mouse interface are provided via P13; where the PS/2 voltage is selectable with
J1. Refer to the specification printed on the bottom of the keyboard and mouse to determine which voltage to select; in most cases this is 5V.
Connectors & Jumpers
Function PS/2 Keyboard and Mouse
Locations
P13
Type
Molex 0532610671 connector
Pinout
Pin
1
2
3
4
5
6
Signal
KDAT
KCLK
PS2_GND
PS2_VCC
MDAT
MCLK
Description
Keyboard Data
Keyboard Clock
Filtered digital ground
Filtered PS/2 supply voltage, via
J1
Mouse Data
Mouse Clock
Function PS/2 voltage select
Selects either +3.3Vauxiliary or +5V auxiliary.
Location
J1
Type
1x3 0.1” jumper
Pinout
Position
1-2
2-3 off
Description
+3.3V_A
+5V_A floating
Default
+3.3V
Revision 0.03 19
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Power
Description
The Xtreme/SBC PCI-104 is designed to be powered from an ATX type power supply, and support many of the ACPI features like suspend to RAM. A CR1225 battery holder (P16) provides the VBAT for the
Qseven module.
The Xtreme/SBC PCI-104 generates 3.3V on board, to facilitate alternate powering options.
WARNING:
If using a PCI-104 power supply that supplies voltages to the Xtreme/SBC PCI-104 through the PCI-104 connector, you must ensure this power supply DOES NOT supply +3.3V (as this would conflict with the onboard +3.3V).
Other powering options include
A) +5V & +12V only: The ATX features can be bypassed by powering +5V_SB with same 5 volt supply as the +5V input pins.
B) +5V only: similar to the above cause, but excluding the +12V which is used only by the backlight and
PCI-104 connector. Before attempting this, verify that this configuration is appropriate for the target installation.
Using a PCI-104 Power Supply (Providing Power Through the PCI-104 Bus Connector)
When using a PCI-104 Power Supply that provides power over the PCI-104 bus connector ensure the following:
The PCI-104 Power Supply should ONLY provide +5V and/or +12V power rails. NOT +3.3V as mentioned above.
-
Install a standard 0.1” pitch jumper on pins 5&6 of the QCG002’s ATX power supply connector as shown below. This will connect the +5V rail to the +5V-SB rail.
This jumper needs to be done for the following reasons: o
Some Qseven modules require +5V-SB in order to boot properly o
The QCG002 SuperIO chipset requires +5V-SB to operate properly
Recommended Connect Tech Power Supplies
Xtreme/PSU –
details here
o
PN: PSG003 (PCI-104 Bus Connector Installed) o
PN: PSG006 (No Bus Connectors Installed)
Xtreme/PSU Isolated – details here o
PN: PXG109 (PCI-104 Bus Connector Installed) o
PN: PXG112 (No Bus Connectors Installed) o
PN: PXG309 (PCI-104 Bus Connector Installed – High Voltage Input) o
PN: PXG312 (No Bus Connectors Installed – High Voltage Input)
20 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Connectors & Jumpers
Function ATX input power
Location
P6
Type
JST B15B-EH-A
Pinout
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Signal
+5V
GND
+5V
GND
+5V
+5V_SB
GND
PSON#
PWROK
+3.3V
GND
+12V
+12V
Function Suspend Selection
Selects either S3 or S5.
Location
J7
Type
1x3 2 mm
Pinout
14
15
GND
-12V
Description
+5V input, powers onboard power regulators & Qseven module
Digital Ground
+5V input, powers onboard power regulators & Qseven module
Digital Ground
+5V input, powers onboard power regulators & Qseven module
+5V standby input, powers +3.3V auxiliary power
Digital Ground
Power Supply On
Power OK
+3.3V input, not used by
Xtreme/SBC PCI-104. +3.3V is derived on internally
Digital Ground
+12V input, used by PCI-104 and backlight
+12V input, used by PCI-104 and backlight
Digital Ground
-12V input, not used
Position
1-2
2-3 off
Description
Suspend S3
Suspend S5
Floating
Default
S3
Revision 0.03 21
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Function Power Supply on
Selects either PS_ON# signal from Qseven module or always on
Location
J8
Type
1x3 2mm
Pinout
Position
1-2
2-3 off
Description
Always on
Qseven PS_ON# floating
Default
Qseven PS_ON#
Function Power Button
Use to connect a momentary push button to the Qseven
PWR_BTN# signal.
Location
J9
Type
1x2 2mm header
Pinout
Position
1
2
Description
PWR_BTN#
Ground
22 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Fan Control
Description
If actively cooling is required; P14 can be used to power and control a fan with J2 selecting the fan voltage.
Connectors & Jumpers
Function Fan power/control
Location
P14
Type
JST B15B-EH-A connector
Pinout
Pin
1
2
3
Signal
FAN_SPEED
FAN_PWR
FAN_GND
Description
Speed signal
Fan power selected by J2
Filtered digital ground
Function Fan power Selection
Selects either +5V or +12V.
Location
J2
Type
1x3 0.100” jumper
Pinout
Position
1-2
2-3 off
Description
+12V
+5V
Floating
Default
floating
Function Fan PWM polarity
Selects either positive or negative
Location
J3
Type
1x2 2mm jumper
Pinout
Position
off on
Description
Positive
Negative
Default
floating
Revision 0.03 23
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Battery
Description
A CR1225 battery holder is provided at P16. This is a standard 3V battery, which powers the RTC (real time clock) on the CPU module. In most cases, it is not required to preserve critical BIOS settings as most
Qseven modules have a flash based BIOS.
Connector & LEDs
Function Battery
Location
P16
Type
CR1225 battery holder
24 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Hardware Installation
1.
Ensure all external system power supplies are off.
2.
Install the Qseven module into P1. Be sure to follow the manufacturer’s direction for proper heatsink/heatspreader installation.
3.
Verify all jumper settings from the relevant sections, paying special attention the power selection jumpers
Jumper Function
Selection Position
J1
J2
J3
J4
J5
J6
J7
J8
PS/2 power
Fan Power
Fan PWM polarity
LVDS panel power
+5V
+12V
Positive
+3.3V positive LVDS backlight enable polarity
LVDS Backlight
Power
+12V
Suspend Selection S3
Power Supply On From Qseven module
2-3
1-2
Off
2-3
Off
1-2
1-2
2-3
4.
Install the necessary cables for the application. At a minimum, this would include: a) Power cable, either ATX or +5V/+12V only b) Display cable, either VGA or LVDS c) Keyboard, either PS/2 or USB d) Power button, if applicable
For the relevant cables, see the Cables & Interconnect section of this manual
5.
Stack any necessary PCI-104 modules on top of the Xtreme/SBC PCI-104 via P2, with the appropriate mounting hardware
6.
Connect the appropriate I/O peripherals to the interface cables: keyboard, mouse, Ethernet, monitor, etc.
7.
Connect the power cable to power supply
8.
Turn on the supply.
Revision 0.03 25
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual
Software Installation & Configuration
In general, always refer to the Qseven module’s manual for proper installation of drivers and configuration software; as well as for appropriate BIOS settings.
The following sections provides some specific notes and hints for successful module integration
Operating System Notes
Linux
General
PS/2: Add kernel option i8042.nopnp to ensure keyboard and mouse PS/2 keyboard and mouse operation
Power down: Add kernel option acpi=force to ensure proper software shutdown.
US15W Specific
Graphics: Intel Driver support for the Poulsbo / GMA500) is limited to several distributions (Redhat,
Fedora). See IEGD (Intel Embedded Graphics Driver) website for details http://edc.intel.com/Software/Downloads/IEGD/#compatibility
Other distributions, such as Linux, are supported through the open source community.
Windows
General
Ethernet:
Install the appropriate Ethernet driver from the Qseven module vendor’s website.
US15W Specific
Graphics:
In some cases, the secondary LVDS display will appear washed out, to avoid this ensure the correct version of the IEGD is installed.
26 Revision 0.03
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Cables & Interconnect
The following table summarizes the Xtreme/SBC PCI-104’s headers and lists the matching cables included with the optional cable kit CKG001.
Drawing
Location PCB Connector Cable Part Number Description PCB End Interface End
Number
Hirose Hirose
P3A, P3B CBG071 CTIC-00182 USB (dual) USB 2.0 Type A female
DF13-8P-1.25H(50) DF13A-8S-1.25C
P4
P5
P6
P6
P7
P8
MLE
TSHSM-205-D-06-
G-V-L
MLE
TSHSM-205-D-06-
G-V-L
JST
B15B-EH-
A(LF)(SN)
JST
B15B-EH-
A(LF)(SN)
Hirose
DF14-30P-
1.25H(25)
Hirose
DF13-8P-1.25H(50)
CBG065
CBG070
CBG074
CBG075
CBG076
CBG078
CTIC-00181
CTIC-00180
CTIC-00184
CTIC-00185
CTIC-00196
GBE
VGA
ATX power
5V / 12V only power
LVDS un-terminated
CTIC-00198 Backlight un-terminated
P9, P11
P10A, P10B
P13
J9
MLE
TSHSM-210-D-06-
G-V-L
Molex
470804005
Molex
532610671
Samtec
TMM-102-02-L-S
Hirose
CBG073
CBG079
CBG072
CBG080
CTIC-00183
CTIC-00199
CTIC-00186
CTIC-00200
Serial (dual)
SATA
Keyboard and Mouse
Power Button
P14 CBG081 CTIC-00201 Fan Power
DF13-3P-1.25H(20)
Cable drawings are available upon request ( [email protected] )
2x5 2mm socket
2x5 2mm socket
JST
EHR-15
JST
EHR-15
Hirose
DF14-30S-1.25C
Hirose
DF13A-8S-1.25C
2x10 2mm socket
SATA
Molex
51021-0600
1x2 2mm socket
Hirose
DF13A-3S-1.25C
RJ45 socket, GBE Ethernet
VGA HD15 Female
ATX 20 pin male
Molex disk drive power male
N/A
N/A
2 X DB-9 Male
SATA
2 X 6 Mini-Din
Momentary Pushbutton
N/A
Revision 0.03 27
Dimensions
Dimension
A
B
C
D
Full 3D Dimensions
Value
3.550” / 90.170mm
3.775” / 95.885mm
3.125” / 79.375mm
0.500” / 12.700mm
Download 3D STEP Model File Here
28
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual
Specifications
Form Factor
Display
Storage
Serial Interface
PCI-104, (Support up to 4 installed PCI-104 add-on boards)
VGA, LVDS flat panel
2x SATA (7 pin connector)
USB
Ethernet
Dimensions
2x RS-232, 2x RS-485
4x USB 2.0
1x Gigabit Ethernet
Temperature
Power
PC/104 compliant
-20ºC to 70ºC (-4ºF to 158ºF)
[1]
ATX supply input
Power Consumption
850 mA @ 5V
Qseven carrier circuitry only. Does not include module power.
PS/2 keyboard and mouse
Additional I/O
Warranty and Support
Lifetime warranty and free technical support
[1] Temperature range is limited by the SDVO to VGA conversion circuitry.
Revision 0.03 29
advertisement
Related manuals
Frequently Answers and Questions
What type of power supplies are recommended for the device?
What type of connector is used for the Qseven module interface?
What are the dimensions of the single board computer?
What is the purpose of the battery?
Which operating systems are supported by the device?
advertisement
Table of contents
- 4 Customer Support Overview
- 4 Contact Information
- 5 Limited Lifetime Warranty
- 5 Copyright Notice
- 5 Trademark Acknowledgment
- 5 Revision History
- 6 Introduction
- 6 Features
- 7 System Block Diagram
- 8 Hardware Description
- 8 Connector Locations
- 9 Qseven Module Interface
- 9 Description
- 9 Connector
- 9 Graphics
- 9 VGA
- 9 Description
- 9 Connector
- 10 LVDS
- 10 Description
- 10 Connectors & Jumpers
- 13 Gigabit Ethernet
- 13 Description
- 13 Connector & LEDs
- 14 USB 2.0
- 14 Description
- 14 Connector
- 15 SATA
- 15 Description
- 16 PCI-104
- 16 Description
- 16 Connectors
- 17 LPC Super I/O
- 17 Serial
- 17 Description
- 18 Connectors
- 19 PS/2 Keyboard and Mouse
- 19 Description
- 19 Connectors & Jumpers
- 20 Power
- 20 Description
- 20 Using a PCI-104 Power Supply (Providing Power Through the PCI-104 Bus Connector)
- 20 Recommended Connect Tech Power Supplies
- 21 Connectors & Jumpers
- 23 Fan Control
- 23 Description
- 23 Connectors & Jumpers
- 24 Battery
- 24 Description
- 24 Connector & LEDs
- 25 Hardware Installation
- 26 Software Installation & Configuration
- 26 Operating System Notes
- 26 Linux
- 26 General
- 26 US15W Specific
- 26 Windows
- 26 General
- 26 US15W Specific
- 27 Cables & Interconnect
- 28 Dimensions
- 29 Specifications