DCS C-24 User guide

Installation instructions

DishDrawer®

DD24DT models

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.dcsappliances.com or contact your local DCS Customer Care Representative.

US CA

1

SAFETY AND WARNINGS

WARNING!

Electrical hazard

Before installing the DishDrawer®, remove the house fuse or open the circuit breaker.

If permanently connecting the DishDrawer®, be sure the power is isolated and the DishDrawer® unplugged.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a electrician or service representative if you are in doubt as to whether the appliance is properly grounded.

If the DishDrawer is installed as a permanently connected appliance:

GROUNDING INSTRUCTIONS - This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-groounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

Do not modify the power supply plug provided with the appliance - if it will not

the outlet, have a proper outlet installed by a an extension cord, adapter plug or multiple outlet box.

ed electrician. Do not use

Failure to follow this advice may result in electrical shock or death.

Important safety instructions!

Installation of this DishDrawer® requires basic mechanical and electrical skills.

Be sure to leave these Instructions with the Customer.

Installation must comply with your local building and electricity regulations.

At the completion of the DishDrawer® installation, the Installer must perform

Final Check List.

Remove all packaging materials supplied with the DishDrawer®.

This DishDrawer® is manufactured for indoor use only.

Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations.

The DishDrawer® MUST be installed to allow for future removal from the enclosure if service is required.

The switched power outlet must be outside the DishDrawer® cavity so that it is accessible after installation.

Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord.

If the DishDrawer® is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage.

Make sure only new hoses are used for connection (supplied with DishDrawer®). Old hoses should not be reused.

Failure to install the DishDrawer® correctly could invalidate any warranty or liability claims.

If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product.

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

I

2

PRODUCT DIMENSIONS

Installation diagrams for illustration purposes only

D

K

C

M

H

B

G

E

L

A

N

F

J

Product dimensions (inches (mm))

A overall height* of product

B overall width of product

C overall depth of product (excl. curvature/handle)

D depth of drawer (open) (excl. curvature/handle)

E height* of chassis

F height range of levelling feet

G depth of chassis (incl. trimseal)

H depth of drawer front panel (excl. curvature/handle)

I depth of handle

J depth of toekick

K height of upper drawer front

L height of lower drawer front

M height of installation bracket slots (on top of chassis)

N height of drawer fronts

* Chassis heights include bracket slots

Note: height from top of handle to top of drawer - (62 mm).

I

2 ¼

(863.5- 923.5)

(605)

(577)

(545)

(853)

(60)

21 ¾ ” (552)

1 ” (25)

(81)

(57 - 117)

(442)

(312)

(2)

30 ” (762)

C

G M

3

CABINETRY DIMENSIONS

Installation diagrams for illustration purposes only B

C

Cabinetry dimensions (inches (mm))

A inside height of cavity

B inside width of cavity

C inside depth of cavity (inside)

D height of adjacent cabinetry

E height of toekick space

Minimum clearances (inches (mm))

” ( 2.5 mm)

” ( 2.5 mm)

34 - 36 ½ ”

(864 - 926.5)

24 ” (610)

22 ” (580)

30” (762)

3 - 6 ” (100 - 160)

½ ” ( 13 mm)

D A

E

4

PARTS SUPPLIED

Drain hose support (1)

Drain hose joiner (1)

Wire clip (2) Clamp (1) Side mounting bracket kit

(A and B) (2)

OPTIONAL

Top mounting brackets (2)

Phillips

16 mm screws (9)

Rubber washer for inlet hose

(1)

Moisture protection tape (1)

(to prevent moisture damage)

Edge protector (1)

(if services hole partition is metal)

Hexagonal socket (2)

(long & short)

Prefinished toekick (1) white or black

If the Drain hose(s) supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose(s) by 11’ 10” (3.6 m). The kit is available from the nearest

DCS Authorized Service Agent, or Toll free 1.888.936.7872 or www.dcsappliances.com.

5

CAVITY PREPARATION

Important!

Be sure the edges of the services hole are smooth or covered. If the services hole is through a metal partition the hole must be protected with the Edge protector supplied to prevent damage to the power cord or hoses.

These marks indicate mounting bracket screw locations

* Preferred position. If adequate clearance, services hole can be higher to clear toekick space.

If hole is higher, ensure drain hose(s) are routed straight into the waste connection.

Water Connection

Recommended HOT (Maximum 140°F/60°C).

Supplied hose to suit 3/8” (9 mm) male compression fitting.

If no side partition, use a brace for securing.

2” x 4”

Water Pressure

Water softener models

Other models

Max

1 MPa (145 psi)

1 MPa (145 psi)

Min

0.1 MPa (14.5 psi)

0.03 MPa (4.3 psi)

Drains will need to be separated to satisfy kosher requirements. We suggest you confirm acceptability with your local rabbi in respect to kosher installations.

Max. distance of hoses and cord from chassis edge

Drain hose

Left hand side

Right hand side

Inlet hose

Power cord (excl. plug)

78 ½ ”

(2000 mm)

64 ¾ ”

(1650 mm)

29 ½ ”

(750 mm)

70 ½ ”

(1800 mm)

49”

(1250 mm)

27 ½ ”

(700 mm)

Left hand side

Right hand side

(10 mm)

Moisture protection tape must be applied.

max. ø 1 ½ ”

(38 mm)

*

Note: Se rvices can either side

of DishDr awer®.

ed

* max. 17 ”

(450 mm) Water supply min. 7 ”

(200 mm)

110-120 VAC max. 15 A

6

OPTIONALLY HARD WIRING THE PRODUCT

A

5 ”

30 mm

2

1

3

Ensure the drawer is removed and then rotated counterclockwise to prevent kinked hoses.

C

11

10

Access cover

Remove knock-out for cable clamp. Fit suitable cable clamp for the conduit and terminate the wiring as shown.

Use copper conductors only.

9

12

11

B

4

Remove the access cover

5

6

8

7

Remove Power supply

8 7

D

Ensure the drawer clips on both sides are reset.

16

17

Ensure the drawer is now rotated clockwise back.

15

13

Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward.

15

14

7

ROUTE THE HOSES

Tie together to avoid kinking.

OR

1

2

8

SECURE BY DRAWER REMOVAL

MOVE INTO THE CAVITY

2

If top mounting brackets are being used, ensure they’re securely fitted before sliding product into cavity.

Loosen feet only and take care when pushing the product into the cavity that you do not bend the feet.

9

REMOVE THE DRAWER

2

3

1

5 ”

(150 mm)

3

Ensure hoses and cord are not kinked or twisted.

8

SECURE WITHOUT DRAWER REMOVAL

(FRAMELESS CABINETRY ONLY)

ATTACH SIDE MOUNTING BRACKETS

Clip all four side mounting brackets into their slots using a flat-bladed screwdriver. Ensure they’re securely fitted before sliding product into cavity.

1

3

1

4

Ensure the drawer is removed and then rotated counter-clockwise to prevent kinked hoses.

5

5

9

The mounting slots are in pairs, one on each side diagonally across the product. A bracket must match A slot and B bracket must match B slot.

MOVE INTO THE CAVITY

2

If top mounting brackets are being used, ensure they’re securely fitted before sliding product into cavity.

optional

(x2)

Ensure hoses and cord are not kinked or twisted.

3

When feet are extended, take care when pushing the product into the cavity that you do not bend the feet.

3

1

1

10

LEVEL AND SECURE THE PRODUCT

Ensure product is level and aligning with cabinetry.

Using the most appropriate length Hexagonal socket supplied, fully extend levelling feet up to required distance by hand.

C C

Hexagonal socket

1

A

B max. ¾ ” (19 mm)

2 optional

B

A

The product has three pairs of mounting brackets: a pair of optional brackets on the top (C) and two pairs of formed brackets in the side of the chassis (A,B). Use at least two out of the three pairs to secure the product.

Ensure the sound insulation is repositioned correctly.

x 4

11

REFIT THE DRAWER

5

Ensure the drawer clips on both sides are reset.

1

3

3

4 Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward.

10

SECURE THE PRODUCT

Open the upper drawer halfway.

Using a flat-bladed screwdriver, prize the plastic gray plug out of the trim moulding.

1

Using a small Philips screwdriver, screw through the trim moulding, securing the side mounting bracket to the cabinetry. Do not damage the rubber trimseal.

2 max.

4

OPTIONAL

¾ ” (19 mm) optional

3

Replace the plastic gray plug back into the trim moulding and ensure the trimseal is facing forward.

4 Repeat for all four brackets.

FINALLY, FOR BOTH METHODS, FIT THE TOEKICK

3 4

5

1

Where the toekick meets the bottom of the tub is the cut-off point

19

19

2

6 7

4

Ensure the drawer is now rotated clockwise back.

1

2

8

Important!

Do not overtighten screw.

9

12

PLUMBING AND DRAINAGE OPTIONS

A

DishDrawer® with Waste Disposal 2

B

DishDrawer® using Air Break with Drain Hose Joiner

If space is limited for fixing, push hose through drain hose support to required height

29 ½” - 34 ¾”

(750 -

882.5 mm)

(

Supplied drain hose joiner

ø ¾ ” (19 mm)) waste tee)

1

Air Break

1

HIGHLOOP min. 6”

(150 mm)

37 ” ( 950 mm)

Max. height to top of Air Break

(countertop or wall mounted) min. R 8 ”

( 200 mm)

Ensure hoses are routed straight to joiner. Remove excess hose material if necessary.

(

Supplied drain hose joiner

ø ¾ ” (19 mm)) waste tee)

3

Fit supplied washer

4

180 o

Ensure hoses are routed straight to joiner. Remove excess hose material if necessary.

Fit supplied washer

4

180 o

5 5

1

C

DishDrawer® and Standpipe

Ø 1 1/2” (38 mm)

If space is limited for fixing, push hose through drain hose support to required height

2 max. 4 ¾”

(120 mm)

1 ½”

(38 mm)

29 ½” - 34 ¾”

(750 -

882.5 mm) min. R 8 ”

( 200 mm)

Waste Disposal

(optional)

Fit supplied washer

4

180 o

5

6 6 6

7 5 5

13

FINAL CHECKLIST

Check all parts are installed.

Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The DishDrawer® must be free to fully close with no resistance from the cabinetry.

Ensure inlet hose to water supply has rubber washer fitted and is tightened a further half turn after seal contact.

Ensure any knockouts or plugs in drain connection have been drilled out and drain connection has been made.

The drain hose joiner must not support the weight of excess hoses. Keep hoses as fully extended as possible to prevent sagging. Any excess length of hose should be kept on the dishwasher side of the high loop.

If using Plumbing and Drainage OPTION A, ensure the Highloop is a minimum

6” (150 mm) higher than the drain hose joiner.

Turn on the power and water supply. Then press the Power ( ) button to turn the DishDrawer® on. The DishDrawer® should beep and Wash Programme lights light up.

Check the spray arm is in place and free to rotate.

Spray arm

Add three cups of water into the DishDrawer®. On the Wash Programme

Selector Panel press Rinse and close the drawer(s). Start the programme by pressing the Start/Pause ( ) button.

After the Rinse programme has finished, ensure machine has run and drained correctly.

Check water supply and drainage connection for leakage.

Repeat for each drawer.

14

TROUBLESHOOTING

Excessive water remaining above the filter plate, after the rinse cycle

Check for kinked drain hoses or blocked waste connection, high loop not properly installed or drain hoses not routed correctly.

No water supply

Check water is connected, turned on and the spray arm(s) are correctly fitted and free to rotate.

No lights come on when the drawer is opened

Ensure power is connected and is switched on. Check if Auto Power option is on.

Water around water supply and drainage connections

Check connections, existing plumbing and hoses for leaks. Check washer and hose clamps are correctly fitted.

If product is tipping

Ensure the product is secured to the cabinetry.

If front panels are misaligned

Check and relevel product. Check the cabinetry is square.

Drawer(s) don’t close properly

Ensure nothing is obstructing the drawer(s) from closing properly eg sound insulation, hoses or drawer latches.

If a problem occurs, consult the Troubleshooting section of the User Guide.

If after checking these points you still need assistance, please refer to the

User guide for warranty details and your nearest Authorized Service Centre, or contact us through our website, www.dcsappliances.com.

www.dcsappliances.com 599745B US CA 04.09