- Computers & electronics
- Networking
- Gateways/controllers
- Witura
- GSM VOIP Gateway Series
- User's manual
advertisement
GSM Fixed Wireless Terminal
WT-1018
User’s Manual
WT-1018 GSM Fixed Wireless Terminal ___________________________________
Contents
Main Features……………………………………………………………………………………………...….3
Caution…………………………………………………………………………………………………......…3
Storage………………………………………………………………………………………………………...3
Sketch of Fixed Wireless Terminal……………………………………………………………………..…….4
Installing SIM Card…………………………………………………………………………………………...5
Setting up the Terminal…..…………………………………………………………………………………...5
Installation for connecting to register cost equipment………………………………………………………..5
Turn on and Turn off Wireless Terminal…………………………………………………………………......6
Making Calls and Answering Incoming Calls………………………………………………………………..6
Programming Code Settings…………………………………………………………………………...……..7
Technical Specification………………………………………………………………………………….……9
Troubleshooting………………………………………………………………………………………….…..
10
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
2
WT-1018 GSM Fixed Wireless Terminal ___________________________________
Main Features
• Adopt advanced microprocessor controlling circuit, run steadily. Capability is ascendant
• Adopt high gains antenna. Signal is strong
• Be applicable for GSM900MHz/DCS1800MHz/PCS 1900MHz
• Call or called function can be set up flexibly
• The functions of locking terminal, locking SIM card, locking network and locking cell can be set up conveniently.
• Function of displaying incoming calls.
• Provide accurate anti-polarity signal for billing equipment to charge
Caution:
1. This terminal should not be used at garage, oil storage and chemical plant or near to flammable or explosive substance.
2. This terminal should be avoided in the hospital. It will interfere medical electronic equipments such as pacemaker and audiphones. This terminal could only be used indoors.
3. If it is found that the terminal is not successful in login onto the network, please check whether the SIM card and antenna are installed well or not.
4. Don’t use the SIM card that has been used in this terminal to other device. Please make sure the initial
PIN code of SIM card is 1234 and disabled when installing SIM card.
5. It is forbidden to touch the antenna when the connected telephone is being used. (being making calls or receiving calls), otherwise the terminal will be damaged. This kind of damage is beyond the range of warranty.
6. When the terminal is using, it should be placed where the signal of network is strong enough. In order to ensure the quality of call voice, the terminal should be far from other electronic equipment.
7. The terminal does not identify SIM card of 5V and 1.8V, only identify 3V SIM card.
8. Don’t disassemble the terminal by yourself. If there is any problem, please contract the authorized personnel.
9. Working voltage of wireless terminal ranges from 6.0V to 7.5V.
Storage
1. Terminal that is packed or not should piled up no more than 10 layers.
2. The terminal should be saved in ventilate and dry place.
3. Don’t knock terminal to avoid breaking the case.
4. Don’t use chemic impregnate to clean terminal, but use dry soft cloth to make it clean.
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
3
WT-1018 GSM Fixed Wireless Terminal ___________________________________
Sketch of the Fixed Wireless Terminal
The WT-1018 Fixed Wireless Terminal
Power Indicator
Network Indicator
Frontal view
LED indicators
LED1 - Power indicator (it’s lit while power source is connected correctly)
LED1 - Signal indicator (Flashing once in one second indicates that the terminal is on GSM network.
Being lit for a long time indicates that the terminal has failed to login onto GSM network)
Back view
1) Antenna port: Connect the antenna to the terminal
2) TEL 1: Connecting to Telephone
3) TEL 2: Connect to PSTN Line
4) On/Off switch: Turn On/Off the terminal
5) Power port: Make the flat side of power adapter plug be upturned and push it in
6) Data port: Connect the RS232 (9-pin) cable to the terminal for GPRS functions (Optional)
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
4
WT-1018 GSM Fixed Wireless Terminal ___________________________________
Installing the SIM Card
Proceed as follows:
1. Slide back the SIM door and lift it up
2. Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines up with the clipped corner of the SIM holder
3. Close the SIM door
4. Slide the SIM door to lock the SIM card in place
Setting up the Terminal
Installation Condition
Require 220v AC power. GSM signal can cover the area where the terminal is placed. Signal quality affects voice quality direct.
The installation for connecting to ordinary telephone direct
1. Install the SIM card proceeding as “Installing the SIM Card” on page 3.
2.
3.
4.
Connect one end of the telephone line to “Telephone port” and the other ends connect to a telephone.
Connect PSTN Line to “Line Port”.
Install the antenna and power supply well. The distance between telephone and terminal is 1.5m at least.
5. Connect one end of the power adapter to “Power port” and another end connects to 220v AC power.
About 10-45 seconds later, the terminal works in gear (The login time is different according to local network).
When the terminal is ready to use, it will display as below
Signal
Power
WT-1018
Draw your attentions: Because there are many types of ordinary telephone and their electric parameters are different .In order to avoid mutual disturbance between telephone and terminal and affects voice quality
.The distance between telephone and terminal must be beyond 2m.
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
5
WT-1018 GSM Fixed Wireless Terminal ___________________________________
The installation for connecting to register cost equipment
If users demand register cost during calls, register cost equipment can be connected between terminal and ordinary telephone. Register cost equipment registers cost according to anti-polarity signal that is provided by terminal.
Turn on and Turn off Wireless Terminal
Turn on: Connect the input end of power adapter to power socket and the output end to the port of
“DC6.5V” turn on terminal. About 15 – 45 seconds later (subject to local wireless network), the terminal will logon successfully.
Turn off: Turn the switch to the OFF side and disconnect power adapter to turn off the terminal
Making Calls
1. Lift the handset or press “hand-free” key, you will hear dialing tone, then you can dial the telephone numbers you want to call.
2. Dialing: dial the telephone numbers you want to call
3. On completion of dialed digits, you can press “#” to transmit telephone numbers. If you don't dial any key for continual 6 seconds during the dialing, the terminal transmits the dialed telephone numbers automatically.
4. If there is PSTN line input, the dialing numbers will automatically go through PSTN line. If the user wants the dialed number to go through GSM then the user must press “*” before the destination numbers.
5. If the user dial an International number start from “0” the dialing numbers will automatically go through GSM.
6. When it is necessary to register cost, the terminal sends out anti-polarity signal (the signal is used to register cost by register cost equipment). During a call, dial digital key or “*” or “#” to output DTMF.
7. If the calling party or called party hangs up, the terminal stops sending out anti-polarity signal.
8. If users dial barred numbers, telephone will give out the sound of three-time toot to ask the user to hang up.
Answering Incoming Calls
When some calls are coming in, the telephone rings and the terminal will displays the incoming telephone numbers on the screen. Now users can lift the handset or press “hand-free” to answer the call.
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
6
WT-1018 GSM Fixed Wireless Terminal ___________________________________
Programming Code Setting (Have to enter Password before Start doing the Settings)
Steps:
1. Password Verification
Pick up phone, press **83211279#
. If heard “du~~~” a continuous dialing tone, means the Password enter correctly, and then will continue to go into programming setting mode. User is able to change the settings now. If there is no continuous “du~~~”, means the Password enter not correct. And it will not go into programming setting mode to change the settings. User can hook-on and pick up phone again to enter the Password.
2. Programming Code
Refer to the Programming Table below. After enter the Programming Code, if you heard a busy tone follow by the dialing tone, it means wrong programming code. If heard continuous “du~~~”, it means the successful set up for that programming code. If just heard dialing tone, it means that the settings area are full or enter wrong programming code.
During the setting for the programming code, user does not need to hook-on the Phone. When user heard dialing tone after ONE setting means the user can continue the following setting.
3. To Quit from the Programming Code Setting
In Hook-on mode or Press “hand free” to quit from the setting.
No. Definition
1 Enter Password. Go into Programming
Setting
Description
Password to the Programming Setting Mode.
(Initial Password for factory leaving is sets up as “83211279”
2 Setting IP or
Gateway Number
*2*XXXXXXXXXXXX#
*2*#
After doing this setting, when making calls, it will automatically dial Gateway
Number in front of the Destination
Number.
Delete the IP or Gateway Number
*3*1*# setting. All the calls are made will not adding Gateway Number in front of the
Destination Number.
Barred all Incoming Calls
Calls
*3*1*0#
Restrict
International Calls
*3*2*0#
*3*3*#
*3*3*0#
Cancel the setting for Barred Incoming
Calls
Barred all Local Calls
Cancel the setting for Barred Local Calls
Barred all International Calls
5 Restrict
Calls
*3*4*#
Cancel the setting for Barred
International Calls
Barred all National Calls
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
7
WT-1018 GSM Fixed Wireless Terminal ___________________________________
Code
Terminal
13 Setting for Changing
Password
Locking
*3*4*0#
Area *1*XXXXXX#
7 Setting adding
“0” in front of destination number
*1*#
*3*5*#
Local
Number Gateway
*3*5*0#
*4*1*#
9 Setting
International Prefix
Number Gateway
*4*1*0#
*4*2*#
National
Prefix Number
Gateway
*4*2*0#
*4*3*# for
SIM Card
*4*3*0#
*5*1*#
*5*1*0#
*5*2*#
*5*2*0#
Cancel the setting for Barred National
Calls
When dialing Local Prefix Number, it will automatically add Local Area Code.
Able to set up to 6 digits for Local Area
Code.
Delete Add Local Area Code.
After doing this setting, when making call for International mobile phone number, it will automatically add 0 in front of the dialed number.
Cancel the setting for adding “0”
After doing this setting, when making
Local Calls, it will automatically dial
Gateway Number in front of the
Destination Number.
Cancel dialing Gateway Number in front of the Local Number
After doing this setting, when making
International Calls, it will automatically dial Gateway Number in front of the
Destination Number
Cancel dialing Gateway Number in front of the International Number
After doing this setting, when making
International Calls, it will automatically dial Gateway Number in front of the
Destination Number.
Cancel dialing Gateway Number in front of the International Number
After doing this setting, the terminal will lock the SIM card with a password.
Note: The terminal can only lock the
SIM card if the SIM card PIN number is
1234 (default) otherwise it will display
“PIN ERROR 02”. The locked SIM card can only be recognized by the terminal for unlocking.
Cancel Locking SIM card. After doing this settings, terminal will unlock the
SIM card and restore the PIN number of the SIM card to 1234 (default).
After doing this setting, the terminal can only accept this particular SIM card.
Only be able to use other SIM after unlocking the phone or deleting the SIM
Card ID
Cancel Locking Terminal. to use the default password “83211279” to go into Programming Setting Mode to be able to use this programming code to change the password.
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
8
WT-1018 GSM Fixed Wireless Terminal ___________________________________
Technical Specification
1. Working condition
Environment temperature: 0 ~ +50ºC
Relative humidity: 10%~95%
Air pressure: 86~106kpa
2. Working frequency: GSM900MHz/GSM1800MHz
3. Stability of frequency: better than 2.5PPM
4. Signal sensitivity: -103dBM
5. Transmit power: <2w
6. Power: 220v±15% AC
7. The max distance between terminal and telephone: 100M
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
9
WT-1018 GSM Fixed Wireless Terminal ___________________________________
Troubleshooting
Phenomena Trouble
Signal indicator isn’t lit
Failed in login onto
GSM network
1. The signal is too weak Please move the terminal to the place where signal is stronger.
2. Check whether antenna is connected well.
3. SIM card is locked. Please contact the service provider.
Signal indicator flashes fast
Signal is too weak
1. Check whether antenna is connected well.
2. The signal is too weak Move the terminal or antenna to the place where signal is strong.
Power indicator isn’t lit
Having not connect to power supply or there is some trouble with power adapter
1. Check whether the adapter is connected well.
2. There is some trouble with the power adapter
Please contact the provider of the terminal.
Only free numbers can be called out
The residual money on SIM card is too less
Add money to the SIM card subscriber
Can’t hear sound during calls
The malfunction on the telephone
Change the connected telephone with a good one
Poor voice quality during calls or there is echo during calls
The voice volume is too high or the signal of network is too weak.
1. Adjust voice volume to be lower.
2. The local signal is too weak. Move the terminal to the place where signal is stronger.
3. Make the antenna is longer from the telephone
4. The voice quality of the connected telephone isn’t good.
Change the connected telephone
5. Trouble on the GSM network.
No ringing sound
The malfunction on the telephone
1. Malfunction on the connected telephone
2. Malfunction on terminal. Please contact the provider of the terminal.
Incoming calls can’t be answered
The connected telephone does not match the terminal or forbidding answering incoming calls is set
1. Change the connected telephone with a suitable one.
2. Forbidding answer incoming calls is set up, please contact the service provider.
We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Witura Corporation.
Phone: +604-2289053 Fax: +604-2289146 Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250, Penang, Malaysia.
10
WT-1018 – User Manual – Rev.1.2 – Technical Support: [email protected]
- www.witura.com
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement