Mitsubishi FDC100VN Specifications


Add to my manuals
44 Pages

advertisement

Mitsubishi FDC100VN Specifications | Manualzz

Before starting use

Heating performance

The heating performance values (kW) described in catalog are the values obtained by operating at an outdoor temperature of 7 C and indoor temperature of 20 C as set forth in the ISO Standards. As the heating performance decreases as the outdoor temperature drops, if the outdoor temperature is too low and the heating performance is insufficient, use other heating appliances as well.

Indication of sound values

The sound values are the values (A scale) measured in a chamber such as an anechoic chamber following the ISO Standards. In the actual installation state, the value is normally larger than the values given in the catalog due to the effect of surrounding noise and echo. Take this into consideration when installing.

Use in oil atmosphere

Avoid installing this unit in as atmosphere where oil scatters or builds up, such as in a kitchen or machine factory.

If the oil adheres to the heat exchanger, the heat exchanging performance will drop, mist may be generated, and the synthetic resin parts may deform and break.

Use in acidic or alkaline atmosphere

If this unit is used in acidic atmosphere such as hot spring areas having high level of sulfuric gases or in alkaline atmosphere including ammonia or calcium chloride, places where the exhaust of the heat exchanger is sucked in, or at coastal areas where the unit is subject to salt breezes, the outer plate or heat exchanger, etc., will corrode. Please ask a dealer or specialist when you use an air conditioner in places differing from a general atmosphere.

Use in places with high ceilings

If the ceiling is high, install a circulator to improve the heat and air flow distribution when heating.

Refrigerant leakage

The refrigerant (R410A) used for Air conditioner is non-toxic and inflammable in its original state.

However, in consideration of a state where the refrigerant leaks into the room, measures against refrigerant leaks must be taken in small rooms where the tolerable level could be exceeded. Take measures by installing ventilation devices, etc.

Use in snowy areas

Take the following measures when installing the outdoor unit in snowy areas.

·Snow prevention

Install a snow-prevention hood so that the snow does not obstruct the air intake port or enter and freeze in the outdoor unit.

·Snow piling

In areas with heavy snow fall, the piled snow could block the air intake port. In this case, a frame that is 50cm or higher than the estimated snow fall must be installed underneath the outdoor unit.

Automatic defrosting device

If the temperature is low, and the humidity is high, frost will stick to the heat exchanger of the outdoor unit. If use is continued, the heating performance will drop.

The "Automatic defrosting device" will function to remove this frost.

After heating for approx, three to ten minutes, it will stop, and the frost will be removed. After defrosting, hot air will be blown again.

Servicing the air-conditioner

After the air-conditioner is used for several seasons, dirt will build up in the air-conditioner causing the performance to drop. In addition to regular servicing, we recommend the maintenance contract (charged for) by a specialist.

Safety Precautions

Air-conditioner usage target

The air-conditioner described in this catalog is a dedicated cooling/heating device for human use.

Do not use it for special applications such as the storage of foodstuffs, animals or plants, precision devices or valuable art, etc.

This could cause the quality of the items to drop, etc.

Do not use this for cooling vehicles or ships. Water leakage or current leaks could occur.

Before use

Always read the "User,s Manual" thoroughly before starting use.

Installation

Always commission the installation to a dealer or specialist. Improper installation will lead to water leakage, electric shocks and fires.

Make sure that the outdoor unit is stable in installation. Fix the unit to stable base.

Usage place

Do not install in places where combustible gas could leak or where there are sparks.

Installation in a place where combustible gas could be generated, flow or accumulate, or places containing carbon fibers could lead to fires.

Our factories are ISO9001 and ISO14001 certified.

Certified ISO 9001 Certified ISO 14001

BIWAJIMA PLANT

Mitsubishi Heavy Industries, Ltd.

Air-conditioning & Refrigeration Systems Headquarters

Certificate number : JQA-0709

MITSUBISHI HEAVY INDUSTRIES-

MAHAJAK AIR CONDITIONERS CO., LTD.

Certificate Number : 04100 1998 0813

Mitsubishi Heavy

Industries-Haier (Quingdao)

Air-conditioners Co.,Ltd.

Certificate Number : 5170-1996-AQ-RCG-RvA

Certificate 04104 1998 0813 E5

BIWAJIMA PLANT

Mitsubishi Heavy Industries, Ltd.

Air-conditioning & Refrigeration Systems Headquarters

Certificate number : JQA-EM0256

MITSUBISHI HEAVY INDUSTRIES-

MAHAJAK AIR CONDITIONERS CO.,LTD.

Certificate Number : 04104 1998 0813 E5

Mitsubishi Heavy

Industries-Haier (Quingdao)

Air-conditioners Co.,Ltd.

Certificate number : 01-1998-083

Japan Head Office:

Mitsubishi Heavy Industries Ltd

16-5 2-Chome Kounan Minato-ku Tokyo

108-8215, Japan www.mhi.co.jp

HB91-10P01E-A-0 February 2010(3B)R

Because of our policy of continuous improvement, we reserve right to make changes in all specifications without notice.

Printed in Japan

High Performance Air-Conditioning

FD

series

Inverter Packaged Air-Conditioners

50/60Hz

10P01E-A-0

Our new advanced technology has realized high efficiency, strong heating and long piping.

This contributes to the environmental protection through energy saving and permits installation of the units (4~6HP) considering a heating operation under temperature conditions down to -20˚C and design flexibility has been improved by extension of piping length to 100m.

NEW

1.5~2.5HP

3HP 4~6HP

Line up

Hyper Inverter

HP

1.5 2 2.5 3 4 5 6 8 10

2

The industry,s highest COP levels are achieved by our latest technologies, such as new high efficient twin rotary compressors and the combination with new Hyper inverter outdoor units.

High efficiency

EER in cooling COP in heating

4.09

3.62

3.71

3.50

3.09

2.81

Micro Hyper

4HP

Micro Hyper Micro

5HP

Hyper

6HP

Micro Hyper

4HP

(comparison of FDT series)

Micro Hyper Micro

5HP

Hyper

6HP

Piping length

50

100m

Long piping

(in case of 4~6HP)

Height difference

(Outdoor higher

than Indoor)

30m

Strong heating

(in case of 4~6HP)

-20 °C

-15 °C

: Heating operation down to -20 °C

: Nominal heating capacity maintained at -15 °C

-20 °C

Heating

+20 °C

-15 °C

Cooling

+43 °C

-30 -20 -10 0 10 20 30 40 50

Max.heating capacity (kW)

Hyper Inverter

FDC100VSX(4HP, 3phase 380V)

FDC125VSX(5HP, 3phase 380V)

FDC140VSX(6HP, 3phase 380V)

Micro Inverter

12.5

16.0

16.5

Leading powerful heating capacity in the industry

Thanks to optimization of refrigeration control with use of electric expansion valve and development of new twin rotary compressors, max heating capacity has been increased.

Hyper Inverter series can reach the set temperature very quickly, keeping nominal heating capacity when outdoor temperature is -15 °C.

It is effective to be used even in cold area.

Temperature of supply air can reach 40 °C in 4 minutes after start up under low temperature operation conditions (at both indoor and outdoor temperature of 2 °C) and can reach 50 °C in 8 minutes after that.

(kW)

18.0

14.5

14.0

8.8

0

Heating capacity (in case of 5HP)

Keeping nominal heating capacity at -15 °C

-15 °C

Hyper Inverter

Micro Inverter nominal heating capacity

14.0kW

2 °C 7 °C model name

FDT100VSX(4HP, 3phase 380V)

FDT125VSX(5HP, 3phase 380V)

FDT140VSX(6HP, 3phase 380V) nominal heating capacity

(kW at outdoor temperature of 7 °C)

11.2kW

14.0kW

16.0kW

heating capacity at outdoor temperature of -15 °C

11.2kW

14.0kW

16.0kW

Please refer to our technical manual for installation conditions, operation range and heating/cooling capacities.

Heating capacity

50 °C

40 °C

30 °C

20 °C

10 °C

0 °C

Hyper Inverter

Micro Inverter

4minutes 8minutes

3

Our new advanced technology has realized high efficiency, strong heating and long piping.

This contributes to the environmental protection through energy saving and permits installation of the units (4~6HP) considering a heating operation under temperature conditions down to -20˚C and design flexibility has been improved by extension of piping length to 100m.

NEW

1.5~2.5HP

3HP 4~6HP

Line up

Hyper Inverter

HP

1.5 2 2.5 3 4 5 6 8 10

2

The industry,s highest COP levels are achieved by our latest technologies, such as new high efficient twin rotary compressors and the combination with new Hyper inverter outdoor units.

High efficiency

EER in cooling COP in heating

4.09

3.62

3.71

3.50

3.09

2.81

Micro Hyper

4HP

Micro Hyper Micro

5HP

Hyper

6HP

Micro Hyper

4HP

(comparison of FDT series)

Micro Hyper Micro

5HP

Hyper

6HP

Piping length

50

100m

Long piping

(in case of 4~6HP)

Height difference

(Outdoor higher

than Indoor)

30m

Strong heating

(in case of 4~6HP)

-20 °C

-15 °C

: Heating operation down to -20 °C

: Nominal heating capacity maintained at -15 °C

-20 °C

Heating

+20 °C

-15 °C

Cooling

+43 °C

-30 -20 -10 0 10 20 30 40 50

Max.heating capacity (kW)

Hyper Inverter

FDC100VSX(4HP, 3phase 380V)

FDC125VSX(5HP, 3phase 380V)

FDC140VSX(6HP, 3phase 380V)

Micro Inverter

12.5

16.0

16.5

Leading powerful heating capacity in the industry

Thanks to optimization of refrigeration control with use of electric expansion valve and development of new twin rotary compressors, max heating capacity has been increased.

Hyper Inverter series can reach the set temperature very quickly, keeping nominal heating capacity when outdoor temperature is -15 °C.

It is effective to be used even in cold area.

Temperature of supply air can reach 40 °C in 4 minutes after start up under low temperature operation conditions (at both indoor and outdoor temperature of 2 °C) and can reach 50 °C in 8 minutes after that.

(kW)

18.0

14.5

14.0

8.8

0

Heating capacity (in case of 5HP)

Keeping nominal heating capacity at -15 °C

-15 °C

Hyper Inverter

Micro Inverter nominal heating capacity

14.0kW

2 °C 7 °C model name

FDT100VSX(4HP, 3phase 380V)

FDT125VSX(5HP, 3phase 380V)

FDT140VSX(6HP, 3phase 380V) nominal heating capacity

(kW at outdoor temperature of 7 °C)

11.2kW

14.0kW

16.0kW

heating capacity at outdoor temperature of -15 °C

11.2kW

14.0kW

16.0kW

Please refer to our technical manual for installation conditions, operation range and heating/cooling capacities.

Heating capacity

50 °C

40 °C

30 °C

20 °C

10 °C

0 °C

Hyper Inverter

Micro Inverter

4minutes 8minutes

3

Compact Design of outdoor units

Line up

Micro Inverter

HP

1.5 2 2.5 3 4 5 6 8 10

Height

390 mm

Height

455 mm

Height

185 mm

4

FDC100VN/VS

(4.0HP)

FDC125VN/VS

(5.0HP)

FDC140VN/VS

(6.0HP)

Easy installation

Size reduction and high efficiency performance on the

DC twin rotary compressors

(Micro Inverter 4-6HP)

Employment of DC twin rotary compressor has enabled to utilize a high-speed range of up to 120 rps at the maximum to secure the required capacity.

Optimum compressor control has been realized by employing the vector control* and the starting current has been improved significantly compared with former models.

Moreover, vibration has been reduced.

Outside diameter of shell

ø185mm

Reduction in height by 22.3%

Reduction in volume by 44.1%

ø133mm

Width

380 mm

4.0

HP

5.0

HP

6.0

HP

8.0

HP

10.0

HP

82

118

125

225

225

74

74

74

122

140

-8

-44

-51

-103

-85

* Comparison with former models

Depth

350 mm

FDC200VS

(8.0HP)

Fits into elevators

Former compressor

New model

DC rotary compressor

* Vector control means a. technique to realize an optimum control by converting the current wave to a smooth sinusoidal waveform

Width

380 mm

Depth

350 mm

FDC250VS

(10.0HP)

4.0

HP

5.0

HP

6.0

HP

8.0

HP

10.0

HP

328

467

467

1643

1643

303

303

303

467

540

8%

35%

35%

72%

67%

* Comparison with former models

Improved efficiency of heat exchanger

Redesigning the fins to a straight shape has reduced the pressure loss of the airflow in the heat exchanger. Surface treatment on the fin has enhanced the frost resistance capacity compared with former models.

Owing to the reduction in the size of heat exchanger, the appropriate number of circuits for each HP has been applied. Employment of a high-speed motor has increased the airflow and enabled to keep the cooling capacity under a condition of higher outdoor air temperatures*.

* Limitation of use is around

43

:

at the maximum.

Former model New model

Controllability

Reliability in the protection of compressor has been improved by optimizing the controls of oil return, electronic expansion valve, etc.

1

2

3

4

5

FDC200VS

(8.0HP)

970mm

370mm

Employment of the scroll inverter compressors

(8/10HP)

A control over wide range of capacity and a high efficiency has been realized by inverter-driven scroll compressors.

In addition, the starting current significantly is improved.

The size has also been reduced by 3.2% in height and 31.8% in volume.

Employment of DC fan motor

Employment of DC fan motor has enabled to realize an excellent efficiency of approx. 60% higher than former models.

Wide range of operation

Our new advanced technology has expanded the heating and cooling operation range.

This permits installation of the units under a low outdoor temperature conditions down to -20 °C In heating operation and

-15 °C in cooling operation.

(FDC 100/125/140)

-20 °C

-30

-15 °C

-20 -10

Heating

0

Cooling

10 20

+20 °C

30 40

+43 °C

50

High technology

POINT

1

DC fan motor uses less energy

POINT

2

Optimization of heat exchanger path.

More efficient heating and cooling

POINT

3

Super heat control with low pressure sensor, works better in tough conditions

POINT

4

High efficiency refrigeration circuit

POINT

5

Newly developed High efficiency DC scroll compressor

Energy labeling “Class A”

MHI models have cleared the class A standard, the highest energy saving level, with their high

COP (coefficient of performance).

A

CLASS

A

D

E

F

G

B

C

Energy

Manufacturer

Outside unit

Inside unit

More efficient

A

Air-conditioner

Less efficient

Annual energy consumption, kWh in cooling mode

(Actual consumption will depend on how the appliance is used and climate)

Cooling output nergy fficiency atio

Full load (the higher the better) kW

Type Cooling only

Cooling + Heating

Air cooled

Water cooled

Heat output

Heating performance

A: higher G: lower

Noise

(dB(A) re 1 pW) kW

Further information is contained in product brochures

Air-conditioner

Energy Label Directive 2002/31/EC

5

Compact Design of outdoor units

Line up

Micro Inverter

HP

1.5 2 2.5 3 4 5 6 8 10

Height

390 mm

Height

455 mm

Height

185 mm

4

FDC100VN/VS

(4.0HP)

FDC125VN/VS

(5.0HP)

FDC140VN/VS

(6.0HP)

Easy installation

Size reduction and high efficiency performance on the

DC twin rotary compressors

(Micro Inverter 4-6HP)

Employment of DC twin rotary compressor has enabled to utilize a high-speed range of up to 120 rps at the maximum to secure the required capacity.

Optimum compressor control has been realized by employing the vector control* and the starting current has been improved significantly compared with former models.

Moreover, vibration has been reduced.

Outside diameter of shell

ø185mm

Reduction in height by 22.3%

Reduction in volume by 44.1%

ø133mm

Width

380 mm

4.0

HP

5.0

HP

6.0

HP

8.0

HP

10.0

HP

82

118

125

225

225

74

74

74

122

140

-8

-44

-51

-103

-85

* Comparison with former models

Depth

350 mm

FDC200VS

(8.0HP)

Fits into elevators

Former compressor

New model

DC rotary compressor

* Vector control means a. technique to realize an optimum control by converting the current wave to a smooth sinusoidal waveform

Width

380 mm

Depth

350 mm

FDC250VS

(10.0HP)

4.0

HP

5.0

HP

6.0

HP

8.0

HP

10.0

HP

328

467

467

1643

1643

303

303

303

467

540

8%

35%

35%

72%

67%

* Comparison with former models

Improved efficiency of heat exchanger

Redesigning the fins to a straight shape has reduced the pressure loss of the airflow in the heat exchanger. Surface treatment on the fin has enhanced the frost resistance capacity compared with former models.

Owing to the reduction in the size of heat exchanger, the appropriate number of circuits for each HP has been applied. Employment of a high-speed motor has increased the airflow and enabled to keep the cooling capacity under a condition of higher outdoor air temperatures*.

* Limitation of use is around

43

:

at the maximum.

Former model New model

Controllability

Reliability in the protection of compressor has been improved by optimizing the controls of oil return, electronic expansion valve, etc.

1

2

3

4

5

FDC200VS

(8.0HP)

970mm

370mm

Employment of the scroll inverter compressors

(8/10HP)

A control over wide range of capacity and a high efficiency has been realized by inverter-driven scroll compressors.

In addition, the starting current significantly is improved.

The size has also been reduced by 3.2% in height and 31.8% in volume.

Employment of DC fan motor

Employment of DC fan motor has enabled to realize an excellent efficiency of approx. 60% higher than former models.

Wide range of operation

Our new advanced technology has expanded the heating and cooling operation range.

This permits installation of the units under a low outdoor temperature conditions down to -20 °C In heating operation and

-15 °C in cooling operation.

(FDC 100/125/140)

-20 °C

-30

-15 °C

-20 -10

Heating

0

Cooling

10 20

+20 °C

30 40

+43 °C

50

High technology

POINT

1

DC fan motor uses less energy

POINT

2

Optimization of heat exchanger path.

More efficient heating and cooling

POINT

3

Super heat control with low pressure sensor, works better in tough conditions

POINT

4

High efficiency refrigeration circuit

POINT

5

Newly developed High efficiency DC scroll compressor

Energy labeling “Class A”

MHI models have cleared the class A standard, the highest energy saving level, with their high

COP (coefficient of performance).

A

CLASS

A

D

E

F

G

B

C

Energy

Manufacturer

Outside unit

Inside unit

More efficient

A

Air-conditioner

Less efficient

Annual energy consumption, kWh in cooling mode

(Actual consumption will depend on how the appliance is used and climate)

Cooling output nergy fficiency atio

Full load (the higher the better) kW

Type Cooling only

Cooling + Heating

Air cooled

Water cooled

Heat output

Heating performance

A: higher G: lower

Noise

(dB(A) re 1 pW) kW

Further information is contained in product brochures

Air-conditioner

Energy Label Directive 2002/31/EC

5

Ceiling Cassette -4way- Indoor units

FDT.FDTC

Individual flap control system

According to room temperature conditions, four directions of air flow can be controlled by individual flap as preferred.

As individual flap control is available even after installation, installation area became wider than before.

Due to optimization of outlet design of air flow with our new advanced technology, sufficient air flow is secured and long reach of air flow is realized.(FDT)

6

Previous

Flap control system

Selection of louver position is possible.

Louvers can be set at different angles.

* RCH-E3 is not applicable to the Individual flap control system and the Flap control system.

Upper position

Movable range

Lower position

The thinnest design

Thanks to new design of heat exchanger changed from 2 parts to 1 part, the height of indoor unit is reduced drastically.

Furthermore applying DC fan motors, the highest energy efficiency level, reduction of weight and significant compact design are realized.

FDT125~140

365mm

298 mm

18% reduction!!

FDT40~71

Shape of heat exchanger

Previous New

270mm

246 mm

9% reduction!!

New

For person who is far from the indoor unit

For both persons who are feeling hot or cold

Can cool both the kitchen and the guests

High efficiency

Reduction of air flow pressure loss

Expansion of outlet air flow area realizes reduction of pressure loss caused by air flow in the indoor unit. Load of fan motor is decreased and efficiency is increased.

Increase of heat transfer efficiency

Applying high efficient piping in heat exchanger and optimization of heat exchanger (2parts 1part) increases heat transfer efficiency.

Achieved COP 5.67

based on 50% capacity of FDT100V in heating operation

Air-conditioners are generally selected with the operation under the most severe ambient temperature conditions.

The inverter constantly adjusts compressor output to meet the exact demand of the indoor units.

i.e. In case that selecting the capacity of an inverter air-conditioner based on heating operation at -5 °C, its capacity drops by

50% at 7 °C(ISO-TI measurement condition) and operation period at 50% capacity is normally longer than that at 100% of nominal heating capacity.

Considering annual electrical power consumption of inverter air-conditioners, it is quite important to give the first priority to 50% actual capacity and selecting inverter air-conditioners is the best solution for saving energy and protecting the environment.

Signal output

A dry contact is equipped on an indoor unit to meet a possible need for signal output on the site.

Convenience

XR1

XR2

XR3

XR4

XR5

XR1

~

5 : approx. DC12v

XR5

XR1

XR2

XR3

XR4 common output1 (run) output2 (heat) output3 (comp on) output4 (alarm) in put

Monitoring Function

Equipped with RS232C for connection directly to your PC monitoring and service tasks made simple with our service software (“Mente PC”).

New remote control

Applying nonpolar 2-core in new remote control line for all indoor units, it is very convenient for installation including renewal case.

Previous

-core

New

Consideration on the Environment

Employment of lead-free solder

Adapt to RoHS

In order to comply with RoHS standard, the new inverter series products use lead-free solder. It was considered to be too difficult to use lead-free solder because it requires higher soldering temperatures at assembling, which could jeopardize the reliability of assembly, etc. PbF soldering method developed by us, however, has enabled a higher reliability for lead-free printed circuit boards.

*"RoHS" is the abbreviation of the new European standard, which means

Restriction of Hazardous Substances.

Employment of the new refrigerant

All models of the New inverter series use a new refrigerant R410A characterized by the ozone depletion coefficient being 0.

Energy Conservation

A High Performance and Excellent Energy Conservation are achieved at the same time by an increased capacity of heat exchanger and employment of high efficiency DC motor etc.

7

Ceiling Cassette -4way- Indoor units

FDT.FDTC

Individual flap control system

According to room temperature conditions, four directions of air flow can be controlled by individual flap as preferred.

As individual flap control is available even after installation, installation area became wider than before.

Due to optimization of outlet design of air flow with our new advanced technology, sufficient air flow is secured and long reach of air flow is realized.(FDT)

6

Previous

Flap control system

Selection of louver position is possible.

Louvers can be set at different angles.

* RCH-E3 is not applicable to the Individual flap control system and the Flap control system.

Upper position

Movable range

Lower position

The thinnest design

Thanks to new design of heat exchanger changed from 2 parts to 1 part, the height of indoor unit is reduced drastically.

Furthermore applying DC fan motors, the highest energy efficiency level, reduction of weight and significant compact design are realized.

FDT125~140

365mm

298 mm

18% reduction!!

FDT40~71

Shape of heat exchanger

Previous New

270mm

246 mm

9% reduction!!

New

For person who is far from the indoor unit

For both persons who are feeling hot or cold

Can cool both the kitchen and the guests

High efficiency

Reduction of air flow pressure loss

Expansion of outlet air flow area realizes reduction of pressure loss caused by air flow in the indoor unit. Load of fan motor is decreased and efficiency is increased.

Increase of heat transfer efficiency

Applying high efficient piping in heat exchanger and optimization of heat exchanger (2parts 1part) increases heat transfer efficiency.

Achieved COP 5.67

based on 50% capacity of FDT100V in heating operation

Air-conditioners are generally selected with the operation under the most severe ambient temperature conditions.

The inverter constantly adjusts compressor output to meet the exact demand of the indoor units.

i.e. In case that selecting the capacity of an inverter air-conditioner based on heating operation at -5 °C, its capacity drops by

50% at 7 °C(ISO-TI measurement condition) and operation period at 50% capacity is normally longer than that at 100% of nominal heating capacity.

Considering annual electrical power consumption of inverter air-conditioners, it is quite important to give the first priority to 50% actual capacity and selecting inverter air-conditioners is the best solution for saving energy and protecting the environment.

Signal output

A dry contact is equipped on an indoor unit to meet a possible need for signal output on the site.

Convenience

XR1

XR2

XR3

XR4

XR5

XR1

~

5 : approx. DC12v

XR5

XR1

XR2

XR3

XR4 common output1 (run) output2 (heat) output3 (comp on) output4 (alarm) in put

Monitoring Function

Equipped with RS232C for connection directly to your PC monitoring and service tasks made simple with our service software (“Mente PC”).

New remote control

Applying nonpolar 2-core in new remote control line for all indoor units, it is very convenient for installation including renewal case.

Previous

-core

New

Consideration on the Environment

Employment of lead-free solder

Adapt to RoHS

In order to comply with RoHS standard, the new inverter series products use lead-free solder. It was considered to be too difficult to use lead-free solder because it requires higher soldering temperatures at assembling, which could jeopardize the reliability of assembly, etc. PbF soldering method developed by us, however, has enabled a higher reliability for lead-free printed circuit boards.

*"RoHS" is the abbreviation of the new European standard, which means

Restriction of Hazardous Substances.

Employment of the new refrigerant

All models of the New inverter series use a new refrigerant R410A characterized by the ozone depletion coefficient being 0.

Energy Conservation

A High Performance and Excellent Energy Conservation are achieved at the same time by an increased capacity of heat exchanger and employment of high efficiency DC motor etc.

7

8

SINGLE [OUTDOOR UNIT : INDOOR UNIT = 1 : 1]

HP kW

Btu/h kcal/h

Indoor unit

1.5

4.0

13,700

3,440

FDT40VD

Outdoor unit

Set

1phase

3phase

1phase

3phase

Indoor unit

SRC40ZIX-S

FDTC40VD

Outdoor unit

Set

1phase

1phase

Indoor unit

SRC40ZIX-S

Outdoor unit

Set

1phase

3phase

1phase

3phase

Indoor unit

Outdoor unit

Set

1phase

3phase

1phase

3phase

Indoor unit

FDEN40VD

Outdoor unit

Set

1phase

3phase

1phase

3phase

SRC40ZIX-S

2.0

5.0

17,100

4,300

FDT50VD

FDEN50VD

2.5

6.0

19,100

4,816

FDT60VD

SRC50ZIX-S SRC60ZIX-S

FDTC50VD FDTC60VD

SRC50ZIX-S SRC60ZIX-S

FDUM50VD FDUM60VD

SRC50ZIX-S SRC60ZIX-S

FDEN60VD

SRC50ZIX-S SRC60ZIX-S

3.0

7.1

23,900

6,020

FDT71VD

FDC71VNX

FDU71VD

*

FDC71VNX

FDUM71VD

FDC71VNX

FDEN71VD

FDC71VNX

4.0

10.0

34,100

8,600

FDT100VD

FDC100VNX

FDC100VSX

FDU100VD

FDC100VNX

FDC100VSX

FDUM100VD

FDC100VNX

FDC100VSX

FDEN100VD

FDC100VNX

FDC100VSX

5.0

12.5

42,700

10,750

6.0

14.0

47,800

12,040

4.0

10.0

34,100

8,600

5.0

12.5

42,700

10,750

Micro Inverter

6.0

14.0

47,800

12,040

8.0

20.0

68,300

17,200

FDT125VD

NEW

FDC125VNX

FDC125VSX

FDT140VD

FDC140VNX

FDC140VSX

FDT100VD

FDC100VN

FDC100VS

FDT125VD FDT140VD

FDC125VN

FDC125VS

FDC140VN

FDC140VS

FDUM125VD

NEW

FDC125VNX

FDC125VSX

FDUM140VD

FDC140VNX

FDC140VSX

FDUM100VD FDUM125VD FDUM140VD

FDC100VN

FDC100VS

FDC125VN

FDC125VS

FDC140VN

FDC140VS

FDEN125VD

NEW

FDC125VNX

FDC125VSX

FDEN140VD

FDC140VNX

FDC140VSX

FDEN100VD FDEN125VD

FDC100VN

FDC100VS

FDC125VN

FDC125VS

FDEN140VD

FDC140VN

FDC140VS

10.0

25.0

85,400

21,500

FDU125VD

NEW

FDC125VNX

FDC125VSX

FDU140VD

FDC140VNX

FDC140VSX

FDU100VD

FDC100VN

FDC100VS

FDU125VD FDU140VD

FDC125VN

FDC125VS

FDC140VN

FDC140VS

FDU200VD

FDC200VS

FDU250VD

FDC250VS

* Not available in 60Hz

9

8

SINGLE [OUTDOOR UNIT : INDOOR UNIT = 1 : 1]

HP kW

Btu/h kcal/h

Indoor unit

1.5

4.0

13,700

3,440

FDT40VD

Outdoor unit

Set

1phase

3phase

1phase

3phase

Indoor unit

SRC40ZIX-S

FDTC40VD

Outdoor unit

Set

1phase

1phase

Indoor unit

SRC40ZIX-S

Outdoor unit

Set

1phase

3phase

1phase

3phase

Indoor unit

Outdoor unit

Set

1phase

3phase

1phase

3phase

Indoor unit

FDEN40VD

Outdoor unit

Set

1phase

3phase

1phase

3phase

SRC40ZIX-S

2.0

5.0

17,100

4,300

FDT50VD

FDEN50VD

2.5

6.0

19,100

4,816

FDT60VD

SRC50ZIX-S SRC60ZIX-S

FDTC50VD FDTC60VD

SRC50ZIX-S SRC60ZIX-S

FDUM50VD FDUM60VD

SRC50ZIX-S SRC60ZIX-S

FDEN60VD

SRC50ZIX-S SRC60ZIX-S

3.0

7.1

23,900

6,020

FDT71VD

FDC71VNX

FDU71VD

*

FDC71VNX

FDC71VNX

FDEN71VD

FDC71VNX

4.0

10.0

34,100

8,600

FDT100VD

FDC100VNX

FDC100VSX

FDU100VD

FDC100VNX

FDC100VSX

FDUM71VD FDUM100VD

FDC100VNX

FDC100VSX

FDEN100VD

FDC100VNX

FDC100VSX

5.0

12.5

42,700

10,750

6.0

14.0

47,800

12,040

4.0

10.0

34,100

8,600

5.0

12.5

42,700

10,750

Micro Inverter

6.0

14.0

47,800

12,040

8.0

20.0

68,300

17,200

FDT125VD

NEW

FDC125VNX

FDC125VSX

FDT140VD

FDC140VNX

FDC140VSX

FDT100VD

FDC100VN

FDC100VS

FDT125VD FDT140VD

FDC125VN

FDC125VS

FDC140VN

FDC140VS

FDUM125VD

NEW

FDC125VNX

FDC125VSX

FDUM140VD

FDC140VNX

FDC140VSX

FDUM100VD FDUM125VD FDUM140VD

FDC100VN

FDC100VS

FDC125VN

FDC125VS

FDC140VN

FDC140VS

FDEN125VD

NEW

FDC125VNX

FDC125VSX

FDEN140VD

FDC140VNX

FDC140VSX

FDEN100VD FDEN125VD

FDC100VN

FDC100VS

FDC125VN

FDC125VS

FDEN140VD

FDC140VN

FDC140VS

10.0

25.0

85,400

21,500

FDU125VD

NEW

FDC125VNX

FDC125VSX

FDU140VD

FDC140VNX

FDC140VSX

FDU100VD

FDC100VN

FDC100VS

FDU125VD FDU140VD

FDC125VN

FDC125VS

FDC140VN

FDC140VS

FDU200VD

FDC200VS

FDU250VD

FDC250VS

* Not available in 60Hz

9

10

[ INDOOR UNIT ]

CEILING CASSETTE -4way-

FDT

A

CLASS

Wired remote control Wireless remote control

FDT 40/50/60/71/

100/125/140VD

Point

1

Arrangement of installation balance of indoor unit

Checking from access ports with detachable covers at each corner, arrangement of installation balance of indoor unit can be available without removing a panel. Workability is improved and time of installation is reduced.

Point

3

Easy checking of drain pan

Easy checking of drain pan condition is available by removing corner lid only.

Due to new design changing fan motor is available without removing a panel. Temporally setting of drain pan is also available.

Outline drawing (Unit:mm)

Model FDT40,50,60,71VD Model 100,125,140VD

RC-E4

(Option)

RCH-E3

(Option)

RCN-T-36W-E

(Option)

Point

2

Installation Workability

For wireless control simply insert the infrared receiver kit on a corner of the panel wireless remote control

RCN-T-36W-E

Point

4

700mm Drain Pump

Drain can be discharged upwards by 700mm from the ceiling surface. It allows a piping layout with a high degree of freedom

Depending on the installation location and 260mm flexible hose as a standard equipment supports easy workability.

Flexible hose less than

700mm

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor

Outdoor

Height x Width x Depth

Unit+Panel

Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size Liquid/Gas

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDT40ZIXVD

FDT40VD

SRC40ZIX-S

FDT50ZIXVD

FDT50VD

SRC50ZIX-S

FDT60ZIXVD

FDT60VD

SRC60ZIX-S

FDT71VNXVD

FDT71VD

FDC71VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDT100VNXVD

FDT100VD

FDC100VNX

4.0

(1.8~4.7)

4.5

(2.0~5.4)

5.0

(2.2~5.6)

5.4

(2.5~6.3)

5.6

(2.8~6.3)

6.7

(3.1~7.1)

7.1

(3.2~8.0)

8.0

(3.6~9.0)

10.0

(4.0~11.2)

11.2

(4.0~12.5)

0.93/1.15

4.30/3.91

A/A

5(12)

1.29/1.29

3.88/4.19

A/A

Hi:33 Me:31 Lo:30

5(14)

1.57/1.85

3.57/3.62

A/A

1.90/2.07

3.74/3.86

A/A

5(17)

Hi:35 Me:33 Lo:31

47

Hi:18 Me:16 Lo:14

40

48

Hi:18 Me:16 Lo:14

Cooling:51 Heating:48

Hi:21 Me:19 Lo:17

Cooling:60 Heating:50

Unit:246x840x840 Panel:35x950x950

27.5(Unit:22 Panel:5.5) 29.5(Unit:24 Panel:5.5)

T-PSA-3AW-E

2.50/2.58

4.00/4.34

A/A

5(24)

Hi:40 Me:37 Lo:35

Cooling:48 Heating:50

Hi:27 Me:24 Lo:20

100

Unit:298x840x840 Panel:35x950x950

32.5(Unit:27 Panel:5.5)

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

640x800(+71)x290

43

Scroll

1.4(15)

6.35/12.7

30

20

20

750x880(+88)x340

60

2.95(30)

50

30

15

Rotary

9.52/15.88

1,300x970x370

105

4.5(30)

100

30

15

-15~43 * 2

-15~20 -20~20

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDT125VNXVD

FDT125VD

FDC125VNX

FDT140VNXVD

FDT140VD

FDC140VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDT100VSXVD

FDT100VD

FDC100VSX

FDT125VSXVD

FDT125VD

FDC125VSX

FDT140VSXVD

FDT140VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

Air flow

1

Exterior dimensions

Net weight

Panel

Air filter, Q'ty

Indoor

Outdoor

Indoor

Outdoor

Height x Width x Depth

Unit+Panel

Range of usage

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

12.5

(5.0~14.0)

14.0

(5.0~16.0)

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(4.0~17.0)

16.0

(4.0~18.0)

11.2

(4.0~16.0)

14.0

(4.0~18.0)

16.0

(4.0~20.0)

3.28/3.43

3.81/4.08

A/A

5(26)

4.19/4.20

3.34/3.81

A/A

2.50/2.58

4.00/4.34

A/A

3.28/3.43

3.81/4.08

A/A

5(15)

Hi:42 Me:40 Lo:37 Hi:42 Me:40 Lo:37

Cooling:48 Heating:50

Hi:43 Me:41 Lo:38

Cooling:49 Heating:52

Hi:30 Me:27 Lo:23

Hi:40 Me:37 Lo:35

Cooling:48 Heating:50

Hi:27 Me:24 Lo:20

100

Unit:298x840x840 Panel:35x950x950

4.19/4.20

3.34/3.81

A/A

Hi:43 Me:41 Lo:38

Cooling:49 Heating:52

Hi:30 Me:27 Lo:23

32.5(Unit:27 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

1,300x970x370

105

Rotary

4.5(30)

9.52/15.88

100

30

15

-15~43 * 2

-20~20

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 40/50ZIXVD 39dB, 60ZIXVD 46dB, 71VNXVD 46dB, 100/125/140VNXVD 51dB, 100/125/140VSXVD 51dB

Air flow: 40/50ZIXVD 20CMM, 60ZIXVD 28CMM, 71VNXVD 28CMM, 100/125/140VNXVD 37CMM, 100/125/140VSXVD 37CMM

11

10

[ INDOOR UNIT ]

CEILING CASSETTE -4way-

FDT

Wired remote control

A

CLASS

Wireless remote control

FDT 40/50/60/71/

100/125/140VD

Point

1

Arrangement of installation balance of indoor unit

Checking from access ports with detachable covers at each corner, arrangement of installation balance of indoor unit can be available without removing a panel. Workability is improved and time of installation is reduced.

Point

3

Easy checking of drain pan

Easy checking of drain pan condition is available by removing corner lid only.

Due to new design changing fan motor is available without removing a panel. Temporally setting of drain pan is also available.

Outline drawing (Unit:mm)

Model FDT40,50,60,71VD Model 100,125,140VD

RC-E4

(Option)

RCH-E3

(Option)

RCN-T-36W-E

(Option)

Point

2

Installation Workability

For wireless control simply insert the infrared receiver kit on a corner of the panel wireless remote control

RCN-T-36W-E

Point

4

700mm Drain Pump

Drain can be discharged upwards by 700mm from the ceiling surface. It allows a piping layout with a high degree of freedom

Depending on the installation location and 260mm flexible hose as a standard equipment supports easy workability.

Flexible hose less than

700mm

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor

Outdoor

Height x Width x Depth

Unit+Panel

Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size Liquid/Gas

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDT40ZIXVD

FDT40VD

SRC40ZIX-S

FDT50ZIXVD

FDT50VD

SRC50ZIX-S

FDT60ZIXVD

FDT60VD

SRC60ZIX-S

FDT71VNXVD

FDT71VD

FDC71VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDT100VNXVD

FDT100VD

FDC100VNX

4.0

(1.8~4.7)

4.5

(2.0~5.4)

5.0

(2.2~5.6)

5.4

(2.5~6.3)

5.6

(2.8~6.3)

6.7

(3.1~7.1)

7.1

(3.2~8.0)

8.0

(3.6~9.0)

10.0

(4.0~11.2)

11.2

(4.0~12.5)

0.93/1.15

4.30/3.91

A/A

5(12)

1.29/1.29

3.88/4.19

A/A

Hi:33 Me:31 Lo:30

5(14)

1.57/1.85

3.57/3.62

A/A

1.90/2.07

3.74/3.86

A/A

5(17)

Hi:35 Me:33 Lo:31

47

Hi:18 Me:16 Lo:14

40

48

Hi:18 Me:16 Lo:14

Cooling:51 Heating:48

Hi:21 Me:19 Lo:17

Cooling:60 Heating:50

Unit:246x840x840 Panel:35x950x950

27.5(Unit:22 Panel:5.5) 29.5(Unit:24 Panel:5.5)

T-PSA-3AW-E

2.50/2.58

4.00/4.34

A/A

5(24)

Hi:40 Me:37 Lo:35

Cooling:48 Heating:50

Hi:27 Me:24 Lo:20

100

Unit:298x840x840 Panel:35x950x950

32.5(Unit:27 Panel:5.5)

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

640x800(+71)x290

43

Scroll

1.4(15)

6.35/12.7

30

20

20

750x880(+88)x340

60

2.95(30)

50

30

15

Rotary

9.52/15.88

1,300x970x370

105

4.5(30)

100

30

15

-15~43 * 2

-15~20 -20~20

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDT125VNXVD

FDT125VD

FDC125VNX

FDT140VNXVD

FDT140VD

FDC140VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDT100VSXVD

FDT100VD

FDC100VSX

FDT125VSXVD

FDT125VD

FDC125VSX

FDT140VSXVD

FDT140VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

Air flow

1

Exterior dimensions

Net weight

Panel

Air filter, Q'ty

Indoor

Outdoor

Indoor

Outdoor

Height x Width x Depth

Unit+Panel

Range of usage

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

12.5

(5.0~14.0)

14.0

(5.0~16.0)

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(4.0~17.0)

16.0

(4.0~18.0)

11.2

(4.0~16.0)

14.0

(4.0~18.0)

16.0

(4.0~20.0)

3.28/3.43

3.81/4.08

A/A

5(26)

4.19/4.20

3.34/3.81

A/A

2.50/2.58

4.00/4.34

A/A

3.28/3.43

3.81/4.08

A/A

5(15)

Hi:42 Me:40 Lo:37 Hi:42 Me:40 Lo:37

Cooling:48 Heating:50

Hi:43 Me:41 Lo:38

Cooling:49 Heating:52

Hi:30 Me:27 Lo:23

Hi:40 Me:37 Lo:35

Cooling:48 Heating:50

Hi:27 Me:24 Lo:20

100

Unit:298x840x840 Panel:35x950x950

4.19/4.20

3.34/3.81

A/A

Hi:43 Me:41 Lo:38

Cooling:49 Heating:52

Hi:30 Me:27 Lo:23

32.5(Unit:27 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

1,300x970x370

105

Rotary

4.5(30)

9.52/15.88

100

30

15

-15~43 * 2

-20~20

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 40/50ZIXVD 39dB, 60ZIXVD 46dB, 71VNXVD 46dB, 100/125/140VNXVD 51dB, 100/125/140VSXVD 51dB

Air flow: 40/50ZIXVD 20CMM, 60ZIXVD 28CMM, 71VNXVD 28CMM, 100/125/140VNXVD 37CMM, 100/125/140VSXVD 37CMM

11

[ INDOOR UNIT ]

CEILING CASSETTE -4way Compact (600 X 600mm)-

FDTC

A

CLASS

Fits into standard

600 x 600 ceiling

Outline drawing (Unit:mm)

FDTC 40/50/60VD

Wired remote control Wireless remote control

12

Point

1

Quiet operation

(Sound level in the Lo mode)

(dB)

36

35

34

33

32

31

30

29

28

27

26

25

35dB

5dB

Down

Previous

(Cooling/Heating)

30dB

3dB

Down

32dB

New

(Cooling)

New

(Heating)

FDTC40/50/60VD

Point

4

Compact Concept

The industry's lowest level 248mm height.

Panel size (700x700) is suitable for 600x600 ceiling panel. All indoor unit size is (WxD: 570x570). It brings easy installation for 600x600 ceiling panel.

Point

2

RC-E4

(Option)

RCH-E3

(Option)

RCN-TC-24W-ER

(Option)

“CLEARER”Air Flow

New shape & angled louver redirects the air current away from the ceiling, to reduce ceiling stains

Point

3

Installation Workability

For wireless control simply insert the infrared receiver kit on a corner of the panel wireless remote control

RCN-TC-24W-ER

Point

5

Comfortable and Convenient

• All units are 18.5kg, light weight unit.

• 600mm Drain Pump is mounted.

Drain can be discharged upward by 600 mm from the ceiling surface close to the indoor unit.

It allows a piping layout with a high degree of freedom depending on the installation location.

• Thanks to width and depth of exterior dimensions of a indoor unit are 570mm each, the installation work can be conducted smoothly with a beautiful finishing in

2x2 ceiling size.

Flexible hose

600mm

Ultra slim design at just 248mm above the ceiling

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDTC40ZIXVD

FDTC40VD

SRC40ZIX-S

FDTC50ZIXVD

FDTC50VD

SRC50ZIX-S

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDTC60ZIXVD

FDTC60VD

SRC60ZIX-S

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor

Outdoor kW kW kW

A dB(A) kg(m)

ø m m m

O/U

O/U

4.0

(1.8~4.7)

4.5

(2.0~5.4)

1.04/1.10

3.85/4.09

A/A

5(12)

5.0

(2.2~5.6)

5.4

(2.5~6.3)

1.56/1.45

3.21/3.72

A/A

5(14)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

47

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

40

Unit:248x570x570 Panel:35x700x700

18.5(Unit:15 Panel:3.5)

TC-PSA-25W-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-TC-24W-ER

640x800(+71)x290

43

Scroll

1.4(15)

6.35/12.7

30

20

20

-15~43* 2

-15~20

5.6

(2.8~6.3)

6.7

(3.1~6.7)

1.99/2.08

2.81/3.22

C/C

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

48

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8 Air flow

Indoor

Outdoor

Exterior dimensions

Net weight

Panel

Height x Width x Depth

Unit+Panel

Air filter, Q'ty

Remote control(option)

Height x Width x Depth Exterior dimensions

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Range of usage

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating

CMM mm kg mm kg

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 40/50/60ZIXVD 47dB Air flow: 40/50/60ZIXVD 13.5CMM

13

[ INDOOR UNIT ]

CEILING CASSETTE -4way Compact (600 X 600mm)-

FDTC

A

CLASS

Fits into standard

600 x 600 ceiling

Outline drawing (Unit:mm)

FDTC 40/50/60VD

Wired remote control Wireless remote control

12

Point

1

Quiet operation

(Sound level in the Lo mode)

(dB)

36

35

34

33

32

31

30

29

28

27

26

25

35dB

5dB

Down

Previous

(Cooling/Heating)

30dB

3dB

Down

32dB

New

(Cooling)

New

(Heating)

FDTC40/50/60VD

Point

4

Compact Concept

The industry's lowest level 248mm height.

Panel size (700x700) is suitable for 600x600 ceiling panel. All indoor unit size is (WxD: 570x570). It brings easy installation for 600x600 ceiling panel.

Point

2

RC-E4

(Option)

RCH-E3

(Option)

RCN-TC-24W-ER

(Option)

“CLEARER”Air Flow

New shape & angled louver redirects the air current away from the ceiling, to reduce ceiling stains

Point

3

Installation Workability

For wireless control simply insert the infrared receiver kit on a corner of the panel wireless remote control

RCN-TC-24W-ER

Point

5

Comfortable and Convenient

• All units are 18.5kg, light weight unit.

• 600mm Drain Pump is mounted.

Drain can be discharged upward by 600 mm from the ceiling surface close to the indoor unit.

It allows a piping layout with a high degree of freedom depending on the installation location.

• Thanks to width and depth of exterior dimensions of a indoor unit are 570mm each, the installation work can be conducted smoothly with a beautiful finishing in

2x2 ceiling size.

Flexible hose

600mm

Ultra slim design at just 248mm above the ceiling

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDTC40ZIXVD

FDTC40VD

SRC40ZIX-S

FDTC50ZIXVD

FDTC50VD

SRC50ZIX-S

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDTC60ZIXVD

FDTC60VD

SRC60ZIX-S

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor

Outdoor kW kW kW

A dB(A) kg(m)

ø m m m

O/U

O/U

4.0

(1.8~4.7)

4.5

(2.0~5.4)

1.04/1.10

3.85/4.09

A/A

5(12)

5.0

(2.2~5.6)

5.4

(2.5~6.3)

1.56/1.45

3.21/3.72

A/A

5(14)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

47

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

40

Unit:248x570x570 Panel:35x700x700

18.5(Unit:15 Panel:3.5)

TC-PSA-25W-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-TC-24W-ER

640x800(+71)x290

43

Scroll

1.4(15)

6.35/12.7

30

20

20

-15~43* 2

-15~20

5.6

(2.8~6.3)

6.7

(3.1~6.7)

1.99/2.08

2.81/3.22

C/C

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

48

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8 Air flow

Indoor

Outdoor

Exterior dimensions

Net weight

Panel

Height x Width x Depth

Unit+Panel

Air filter, Q'ty

Remote control(option)

Height x Width x Depth Exterior dimensions

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Range of usage

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating

CMM mm kg mm kg

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 40/50/60ZIXVD 47dB Air flow: 40/50/60ZIXVD 13.5CMM

13

14

[ INDOOR UNIT ]

DUCT CONNECTED -High Static pressure-

FDU

Wired remote control

Wireless remote control

A

CLASS

R410A

Fan control kit

(100~200Pa)

RC-E4

(Option)

RCH-E3

(Option)

FDU 71/100/125/140VD

RCN-KIT3-E

(Option)

Point

1

Enhanced installation workability

Quiet, Lightweight and Compact

With the FDU71, the noise level is only 37dB (low), weight is only 40kg and height is only 297mm.

In addition 600mm Drain Pump is mounted in FDU71/100/125/140VD.

The indoor unit is completely hidden in the ceiling, so this is suitable for spaces with classy interior decoration.

Height

297mm

600mm

FDU 200/250VD U-FCRA

[For 200/250VD]

(option)

Point

2

Adaptability to higher static pressures

High static pressure of 200 Pa (FDU200/250VD) extends the degree of freedom in the designing of air conditioners.

This is a real and earnest model for duct air-conditioning.

A unit external static pressure of up to 200 Pa

(FDU200/250VD) is possible.

Precise air flow designing is possible.

Control box

Slide type fan system

Fan motor

Thin type duct connection opening

High static pressure silent fan

Outline drawing (Unit:mm)

FDU71VD

FDU100,125,140VD

FDU200,250VD

Installation workability

(FDU200,250VD)

Using piping attachment that has flared connection and brazed connection ends, there is no need conduct brazing work inside the outdoor unit.

Flared connection

ø19.05mm

232mm

Brazed connection

ø22.2mm

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1 Indoor

Outdoor

Air flow

Indoor

Outdoor

External static pressure

Exterior dimensions Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Liquid/Gas

Range of usage

Ref.piping size

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

* FDU71VNXVD

FDU71VD

FDC71VNX

7.1

(3.2~8.0)

8.0

(3.6~9.0)

2.15/2.15

3.30/3.72

A/A

5(17)

Hi:41 Lo:37

Cooling:51 Heating:48

Hi:20 Lo:17

Cooling:60 Heating:50

297x850x650

40

750x880(+88)x340

60

2.95(30)

50

* Not available in 60Hz

* FDU100VNXVD

FDU100VD

FDC100VNX

* FDU125VNXVD

FDU125VD

FDC125VNX

1Phase 220-240V 50Hz

* FDU140VNXVD

FDU140VD

FDC140VNX

10.0

(4.0~11.2)

11.2

(4.0~12.5)

12.5

(5.0~14.0)

14.0

(4.0~17.0)

2.78/2.90

3.60/3.86

A/A

5(25)

Hi:42 Lo:37

Cooling:48 Heating:50

3.44/3.67

3.63/3.81

A/A

5(29)

Hi:34 Lo:27

100

Standard:50, Max:130

350x1,370x650

63

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

Rotary

4.5(30)

9.52/15.88

100

30

15

-15~43* 2

-20~20

14.0

(5.0~16.0)

16.0

(4.0~18.0)

4.20/4.30

3.33/3.72

A/A

5(30)

Hi:43 Lo:38

Cooling:49 Heating:52

Hi:42 Lo:33.5

SPECIFICATIONS * Not available in 60Hz

Set model name

Indoor name

Outdoor name

Power source

* FDU100VSXVD

FDU100VD

FDC100VSX

* FDU125VSXVD

FDU125VD

FDC125VSX

* FDU140VSXVD

FDU140VD

FDC140VSX

3Phase 380-415V 50Hz

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1 Indoor

Outdoor

Air flow

Indoor

Outdoor

External static pressure

Exterior dimensions Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Liquid/Gas

Range of usage

Ref.piping size

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

10.0

(4.0~11.2)

11.2

(4.0~16.0)

2.78/2.90

3.60/3.86

A/A

5(16)

Hi:42 Lo:37

Cooling:48 Heating:50

Hi:34 Lo:27

12.5

(5.0~14.0)

14.0

(4.0~18.0)

3.44/3.67

3.63/3.81

A/A

5(18)

Hi:43 Lo:38

Cooling:48 Heating:50

Hi:42 Lo:33.5

100

Standard:50, Max:130

350x1,370x650

63

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

Rotary

4.5(30)

9.52/15.88

100

30

15

-15~43* 2

-20~20

14.0

(5.0~16.0)

16.0

(4.0~20.0)

4.20/4.30

3.33/3.72

A/A

5(19)

Cooling:49 Heating:52

*

*

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of FDU71/100/125/140 is 60Pa and that of FDU200/250 is 100Pa.

1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

*

2 : External static pressure is changeable to be set by the remote control. Standard external static pressure is factory setting. MAX external static pressure is ''High static pressure'' setting. The values of sound pressure level become 5dB(A) higher at eternal static pressure of 130Pa.

3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

15

14

[ INDOOR UNIT ]

DUCT CONNECTED -High Static pressure-

FDU

Wired remote control

Wireless remote control

A

CLASS

R410A

Fan control kit

(100~200Pa)

RC-E4

(Option)

RCH-E3

(Option)

FDU 71/100/125/140VD

RCN-KIT3-E

(Option)

Point

1

Enhanced installation workability

Quiet, Lightweight and Compact

With the FDU71, the noise level is only 37dB (low), weight is only 40kg and height is only 297mm.

In addition 600mm Drain Pump is mounted in FDU71/100/125/140VD.

The indoor unit is completely hidden in the ceiling, so this is suitable for spaces with classy interior decoration.

Height

297mm

600mm

FDU 200/250VD U-FCRA

[For 200/250VD]

(option)

Point

2

Adaptability to higher static pressures

High static pressure of 200 Pa (FDU200/250VD) extends the degree of freedom in the designing of air conditioners.

This is a real and earnest model for duct air-conditioning.

A unit external static pressure of up to 200 Pa

(FDU200/250VD) is possible.

Precise air flow designing is possible.

Control box

Slide type fan system

Fan motor

Thin type duct connection opening

High static pressure silent fan

Outline drawing (Unit:mm)

FDU71VD

FDU100,125,140VD

FDU200,250VD

Installation workability

(FDU200,250VD)

Using piping attachment that has flared connection and brazed connection ends, there is no need conduct brazing work inside the outdoor unit.

Flared connection

ø19.05mm

232mm

Brazed connection

ø22.2mm

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1 Indoor

Outdoor

Air flow

Indoor

Outdoor

External static pressure

Exterior dimensions Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Liquid/Gas

Range of usage

Ref.piping size

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

* FDU71VNXVD

FDU71VD

FDC71VNX

7.1

(3.2~8.0)

8.0

(3.6~9.0)

2.15/2.15

3.30/3.72

A/A

5(17)

Hi:41 Lo:37

Cooling:51 Heating:48

Hi:20 Lo:17

Cooling:60 Heating:50

297x850x650

40

750x880(+88)x340

60

2.95(30)

50

* Not available in 60Hz

* FDU100VNXVD

FDU100VD

FDC100VNX

* FDU125VNXVD

FDU125VD

FDC125VNX

1Phase 220-240V 50Hz

* FDU140VNXVD

FDU140VD

FDC140VNX

10.0

(4.0~11.2)

11.2

(4.0~12.5)

12.5

(5.0~14.0)

14.0

(4.0~17.0)

2.78/2.90

3.60/3.86

A/A

5(25)

Hi:42 Lo:37

Cooling:48 Heating:50

3.44/3.67

3.63/3.81

A/A

5(29)

Hi:34 Lo:27

100

Standard:50, Max:130

350x1,370x650

63

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

Rotary

4.5(30)

9.52/15.88

100

30

15

-15~43* 2

-20~20

14.0

(5.0~16.0)

16.0

(4.0~18.0)

4.20/4.30

3.33/3.72

A/A

5(30)

Hi:43 Lo:38

Cooling:49 Heating:52

Hi:42 Lo:33.5

SPECIFICATIONS * Not available in 60Hz

Set model name

Indoor name

Outdoor name

Power source

* FDU100VSXVD

FDU100VD

FDC100VSX

* FDU125VSXVD

FDU125VD

FDC125VSX

* FDU140VSXVD

FDU140VD

FDC140VSX

3Phase 380-415V 50Hz

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1 Indoor

Outdoor

Air flow

Indoor

Outdoor

External static pressure

Exterior dimensions Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Liquid/Gas

Range of usage

Ref.piping size

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

10.0

(4.0~11.2)

11.2

(4.0~16.0)

2.78/2.90

3.60/3.86

A/A

5(16)

Hi:42 Lo:37

Cooling:48 Heating:50

Hi:34 Lo:27

12.5

(5.0~14.0)

14.0

(4.0~18.0)

3.44/3.67

3.63/3.81

A/A

5(18)

Hi:43 Lo:38

Cooling:48 Heating:50

Hi:42 Lo:33.5

100

Standard:50, Max:130

350x1,370x650

63

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

Rotary

4.5(30)

9.52/15.88

100

30

15

-15~43* 2

-20~20

14.0

(5.0~16.0)

16.0

(4.0~20.0)

4.20/4.30

3.33/3.72

A/A

5(19)

Cooling:49 Heating:52

*

*

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of FDU71/100/125/140 is 60Pa and that of FDU200/250 is 100Pa.

1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

*

2 : External static pressure is changeable to be set by the remote control. Standard external static pressure is factory setting. MAX external static pressure is ''High static pressure'' setting. The values of sound pressure level become 5dB(A) higher at eternal static pressure of 130Pa.

3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

15

16

[ INDOOR UNIT ]

DUCT CONNECTED -Middle Static pressure-

FDUM

Wired remote control

Wireless remote control

Filter kit

UM-FL1E : for 50

UM-FL2E : for 60, 71

UM-FL3E : for 100, 125, 140

(option) external static pressure loss:5pa

RC-E4

(Option)

RCH-E3

(Option)

RCN-KIT3-E

(Option)

Point

1

Various Adaptability

Selectable static pressure and

Flexible duct design with selectable air suction (direct suction /duct suction) can meet wide pattern of installation.

Static pressure Pa model

50/60/71VD

100VD

125/140VD

Standard

50

60

60

(50Hz)

Max

85

90

85

Outline drawing(Unit:mm)

Model FDUM50VD

A

CLASS

FDUM 50/60/71/

100/125/140VD

Point

2

600mm Drain Pump

Drain can be discharged upwards by 600mm from the ceiling surface. It allows a piping layout with a high degree of freedom Depending on the installation location.

Flexible hose less than

600mm

Models FDUM60V,71VD Models FDUM100V,125V,140VD

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor

Outdoor

Air flow

Indoor

Static pressure

Outdoor

50Hz/60Hz

Height x Width x Depth Exterior dimensions

Net weight

Air filter, Q'ty

Range of usage

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDUM50ZIXVD

FDUM50VD

SRC50ZIX-S

FDUM60ZIXVD

FDUM60VD

SRC60ZIX-S

FDUM71VNVD

FDUM71VD

FDC71VNX

FDUM100VNXVD

FDUM100VD

FDC100VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

5.0

(2.2~5.6)

5.6

(2.8~6.3)

7.1

(3.2~8.0)

10.0

(4.0~11.2)

5.4

(2.5~6.3)

1.52/1.41

6.7

(3.1~7.1)

1.86/1.96

8.0

(3.6~9.0)

2.14/2.16

3.29/3.83

A/A

3.01/3.42

B/B

3.32/3.70

A/A

47

5(14)

Hi:34 Me:31 Lo:28

Hi:13 Me:12 Lo:11

Standard:50/40, Max:85/90

40

5(17)

Hi:35 Me:32 Lo:29

48

Hi:16 Me:15 Lo:14

Cooling:51 Heating:48

Hi:20 Me:18 Lo:15

Cooling:60 Heating:50

Standard:50/40, Max:85/100

299x750x635

34

299x950x635

40

Procure locally

640x800(+71)x290

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

750x880(+88)x340

60 43

Scroll

1.4(15)

6.35/12.7

2.95(30)

30

20

20

50

-15~43* 2

-15~20

Rotary

9.52/15.88

30

15

-20~20

11.2

(4.0~12.5)

2.72/2.95

3.68/3.80

A/A

5(24)

Hi:37 Me:35 Lo:32

Cooling:48 Heating:50

Hi:28 Me:25 Lo:22

100

Standard:60/60, Max:90/100

350x1,370x635

59

1,300x970x370

105

4.5(30)

100

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDUM125VNXVD

FDUM125VD

FDC125VNX

FDUM140VNXVD

FDUM140VD

FDC140VNX

FDUM100VSXVD

FDUM100VD

FDC100VSX

FDUM125VSXVD

FDUM125VD

FDC125VSX

FDUM140VSXVD

FDUM140VD

FDC140VSX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz 3Phase 380-415V 50Hz, 3Phase 380V 60Hz

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor

Outdoor

Air flow

Indoor

Outdoor

Static pressure

Exterior dimensions

Ref.amount precharged

Ref.piping size

Ref.piping length

50Hz/60Hz

Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Type of compressor

Liquid/Gas

Range of usage

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

12.5

(5.0~14.0)

14.0

(5.0~16.0)

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(4.0~17.0)

3.62/3.77

16.0

(4.0~18.0)

4.34/4.69

11.2

(4.0~16.0)

2.72/2.95

14.0

(4.0~18.0)

3.62/3.77

16.0

(4.0~20.0)

4.34/4.69

3.45/3.71

A/A

Hi:38 Me:36 Lo:33

Cooling:48 Heating:50

5(26)

3.23/3.41

A/B

Cooling:49 Heating:52

Standard:60/55, Max:85/100

3.68/3.80

A/A

Hi:37 Me:35 Lo:32

Cooling:48 Heating:50

Hi:28 Me:25 Lo:22

100

3.45/3.71

A/A

5(15)

3.23/3.41

A/B

Hi:38 Me:36 Lo:33

Cooling:49 Heating:52

Standard:60/55, Max:85/100 Standard:60/60, Max:90/100

350x1,370x635

59

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

Rotary

4.5(30)

9.52/15.88

100

30

15

-15~43* 2

-20~20

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of indoor units is 60Pa.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 50ZIXVD 35dB, 60ZIXVD 38dB, 71VNXVD 38dB, 100/125/140VNXVD 41dB, 100/125/140VSXVD 41dB

Air flow: 50ZIXVD 14CMM, 60ZIXVD 18CMM, 71VNXVD 23CMM, 100/125/140VNXVD 34CMM, 100/125/140VSXVD 34CMM

17

16

[ INDOOR UNIT ]

DUCT CONNECTED -Middle Static pressure-

FDUM

Wired remote control

Wireless remote control

Filter kit

UM-FL1E : for 50

UM-FL2E : for 60, 71

UM-FL3E : for 100, 125, 140

(option) external static pressure loss:5pa

RC-E4

(Option)

RCH-E3

(Option)

RCN-KIT3-E

(Option)

Point

1

Various Adaptability

Selectable static pressure and

Flexible duct design with selectable air suction (direct suction /duct suction) can meet wide pattern of installation.

Static pressure Pa model

50/60/71VD

100VD

125/140VD

Standard

50

60

60

(50Hz)

Max

85

90

85

Outline drawing(Unit:mm)

Model FDUM50VD

A

CLASS

FDUM 50/60/71/

100/125/140VD

Point

2

600mm Drain Pump

Drain can be discharged upwards by 600mm from the ceiling surface. It allows a piping layout with a high degree of freedom Depending on the installation location.

Flexible hose less than

600mm

Models FDUM60V,71VD Models FDUM100V,125V,140VD

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor

Outdoor

Air flow

Indoor

Static pressure

Outdoor

50Hz/60Hz

Height x Width x Depth Exterior dimensions

Net weight

Air filter, Q'ty

Range of usage

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDUM50ZIXVD

FDUM50VD

SRC50ZIX-S

FDUM60ZIXVD

FDUM60VD

SRC60ZIX-S

FDUM71VNVD

FDUM71VD

FDC71VNX

FDUM100VNXVD

FDUM100VD

FDC100VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

5.0

(2.2~5.6)

5.6

(2.8~6.3)

7.1

(3.2~8.0)

10.0

(4.0~11.2)

5.4

(2.5~6.3)

1.52/1.41

6.7

(3.1~7.1)

1.86/1.96

8.0

(3.6~9.0)

2.14/2.16

3.29/3.83

A/A

3.01/3.42

B/B

3.32/3.70

A/A

47

5(14)

Hi:34 Me:31 Lo:28

Hi:13 Me:12 Lo:11

Standard:50/40, Max:85/90

40

5(17)

Hi:35 Me:32 Lo:29

48

Hi:16 Me:15 Lo:14

Cooling:51 Heating:48

Hi:20 Me:18 Lo:15

Cooling:60 Heating:50

Standard:50/40, Max:85/100

299x750x635

34

299x950x635

40

Procure locally

640x800(+71)x290

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

750x880(+88)x340

60 43

Scroll

1.4(15)

6.35/12.7

2.95(30)

30

20

20

50

-15~43* 2

-15~20

Rotary

9.52/15.88

30

15

-20~20

11.2

(4.0~12.5)

2.72/2.95

3.68/3.80

A/A

5(24)

Hi:37 Me:35 Lo:32

Cooling:48 Heating:50

Hi:28 Me:25 Lo:22

100

Standard:60/60, Max:90/100

350x1,370x635

59

1,300x970x370

105

4.5(30)

100

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDUM125VNXVD

FDUM125VD

FDC125VNX

FDUM140VNXVD

FDUM140VD

FDC140VNX

FDUM100VSXVD

FDUM100VD

FDC100VSX

FDUM125VSXVD

FDUM125VD

FDC125VSX

FDUM140VSXVD

FDUM140VD

FDC140VSX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz 3Phase 380-415V 50Hz, 3Phase 380V 60Hz

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor

Outdoor

Air flow

Indoor

Outdoor

Static pressure

Exterior dimensions

Ref.amount precharged

Ref.piping size

Ref.piping length

50Hz/60Hz

Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Type of compressor

Liquid/Gas

Range of usage

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

12.5

(5.0~14.0)

14.0

(5.0~16.0)

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(4.0~17.0)

3.62/3.77

16.0

(4.0~18.0)

4.34/4.69

11.2

(4.0~16.0)

2.72/2.95

14.0

(4.0~18.0)

3.62/3.77

16.0

(4.0~20.0)

4.34/4.69

3.45/3.71

A/A

Hi:38 Me:36 Lo:33

Cooling:48 Heating:50

5(26)

3.23/3.41

A/B

Cooling:49 Heating:52

Standard:60/55, Max:85/100

3.68/3.80

A/A

Hi:37 Me:35 Lo:32

Cooling:48 Heating:50

Hi:28 Me:25 Lo:22

100

3.45/3.71

A/A

5(15)

3.23/3.41

A/B

Hi:38 Me:36 Lo:33

Cooling:49 Heating:52

Standard:60/55, Max:85/100 Standard:60/60, Max:90/100

350x1,370x635

59

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

Rotary

4.5(30)

9.52/15.88

100

30

15

-15~43* 2

-20~20

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of indoor units is 60Pa.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 50ZIXVD 35dB, 60ZIXVD 38dB, 71VNXVD 38dB, 100/125/140VNXVD 41dB, 100/125/140VSXVD 41dB

Air flow: 50ZIXVD 14CMM, 60ZIXVD 18CMM, 71VNXVD 23CMM, 100/125/140VNXVD 34CMM, 100/125/140VSXVD 34CMM

17

[ INDOOR UNIT ]

CEILING SUSPENDED

FDEN

A

CLASS

Wired remote control

FDEN 40/50/60/71/100/125/140VD

Wireless remote control

RC-E4

(Option)

RCH-E3

(Option)

RCN-E1R

(Option)

Point

1

Improved installation workability

Increased freedom of a piping layout

Up

Point

2

Compact and modern design

Height

210mm

Right

Rear

The refrigerant pipe from the unit can be arranged in three directions, rear, right and up. The drain pipe can be arranged in two directions, left and right. This will allow a free layout of piping for various installation conditions. The unit can only be serviced from the bottom.

All models fit compactly on ceiling. (Height-210mm or 250mm).

Plain, modern design featuring rounded edges gives room a comfortable atmosphere.

FDEN40VD, 50VD weights 30kg the lightest level in the industry.

Convenient and quick installation.

18

Outline drawing (Unit:mm)

24

40

Drain hole connection(1)

(VP20(I.D.20))

76 a (Suspension bolts pitch)

Air inlet grille b c

Gas piping

(VP20(I.D.20))

24

290(Suspension bolts pitch)

135

68

410

Holes for suspension bolts

(M8 to M10X 4pcs.Not included)

145

52

Liquid piping

Gas piping

40

Air outlet

Indication board

690

195

235

271

Note(1) The slope of drain piping

inside the unit is able

to take incline of 10mm.

(VP20 (I.D.20))

75

110

135

Liquid piping

Space for installation and service

100 or more or more 150 or more

Obstacles

5 or more

Dimension Table model

FDEN40,50

FDEN60,71

FDEN100~140 a

1022

1272

1572 b

990

1240

1540 c

1070

1320

1620 d

215

215

255 e

210

210

250

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Energy label

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

Air flow

1

Exterior dimensions

Net weight

Indoor

Outdoor

Indoor

Outdoor

Height x Width x Depth

Range of usage

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN40ZIXVD

FDEN40VD

SRC40ZIX-S

FDEN50ZIXVD

FDEN50VD

SRC50ZIX-S

FDEN60ZIXVD

FDEN60VD

SRC60ZIX-S

FDEN71VNXVD

FDEN71VD

FDC71VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDEN100VNXVD

FDEN100VD

FDC100VNX

4.0

(1.8~4.7)

4.5

(2.0~5.4)

5.0

(2.2~5.6)

5.4

(2.5~6.3)

5.6

(2.8~6.3)

6.7

(3.1~7.1)

7.1

(3.2~8.0)

8.0

(3.6~9.0)

10.0

(4.0~11.2)

11.2

(4.0~12.5)

1.04/1.13

3.85/3.98

A/A

5(12)

1.59/1.58

3.14/3.42

B/B

1.95/2.12

2.87/3.16

C/D

2.11/2.11

3.36/3.79

A/A

2.80/2.88

3.57/3.89

A/A

Hi:39 Me:38 Lo:37

47

Hi:11 Me:9 Lo:7

210x1,070x690

28

40

5(14)

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

640x800(+71)x290

43

750x880(+88)x340

60

5(24)

48

Hi:41 Me:39 Lo:38 Hi:44 Me:41 Lo:39

Cooling:51 Heating:48 Cooling:48 Heating:50

Hi:18 Me:14 Lo:12 Hi:18 Me:14 Lo:12 Hi:26 Me:23 Lo:21

Cooling:60 Heating:50

210x1,320x690

37

5(17)

100

250x1,620x690

49

1,300x970x370

105

Scroll

1.4(15)

6.35/12.7

30

20

20

2.95(30)

Rotary

9.52/15.88

50

30

15

4.5(30)

-15~43* 2

-15~20 -20~20

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDEN125VNXVD

FDEN125VD

FDC125VNX

FDEN140VNXVD

FDEN140VD

FDC140VNX

FDEN100VSXVD

FDEN100VD

FDC100VSX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDEN125VSXVD

FDEN125VD

FDC125VSX

FDEN140VSXVD

FDEN140VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

Nominal cooling capacity

(Min~Max)

ISO-T1(JIS)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor

Outdoor

Air flow

Exterior dimensions

Net weight

Air filter, Q'ty

Indoor

Outdoor

Height x Width x Depth

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Range of usage

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

12.5

(5.0~14.0)

14.0

(4.0~17.0)

14.0

(5.0~16.0)

16.0

(4.0~18.0)

10.0

(4.0~11.2)

11.2

(4.0~16.0)

12.5

(5.0~14.0)

14.0

(4.0~18.0)

14.0

(5.0~16.0)

16.0

(4.0~20.0)

3.86/3.77

3.24/3.71

A/A

5(26)

4.98/4.69

2.81/3.41

Hi:46 Me:44 Lo:43

Cooling:48 Heating:50 Cooling:49 Heating:52

Hi:29 Me:26 Lo:23

C/B

2.80/2.88

3.57/3.89

A/A

Hi:44 Me:41 Lo:39

Cooling:48 Heating:50

Hi:26 Me:23 Lo:21

100

250x1,620x690

49

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

1,300x970x370

105

3.86/3.77

3.24/3.71

4.98/4.69

2.81/3.41

A/A

5(15)

C/B

Hi:46 Me:44 Lo:43

Cooling:48 Heating:50 Cooling:49 Heating:52

Hi:29 Me:26 Lo:23

100

Rotary

4.5(30)

9.52/15.88

50

30

15

-15~43* 2

-20~20

100

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB.

Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 40/50ZIXVD 46dB, 60ZIXVD 50dB, 71VNXVD 50dB, 100VNXVD 46dB, 125/140VNXVD 50dB, 100VSXVD 46dB, 125/140VSXVD 50dB

Air flow: 40/50ZIXVD 13CMM, 60ZIXVD 22CMM, 71VNXVD 22CMM, 100VNXVD 28CMM, 125/140VNXVD 32CMM, 100VSXVD 28CMM, 125/140VSXVD 32CMM

19

[ INDOOR UNIT ]

CEILING SUSPENDED

FDEN

A

CLASS

Wired remote control

FDEN 40/50/60/71/100/125/140VD

Wireless remote control

RC-E4

(Option)

RCH-E3

(Option)

RCN-E1R

(Option)

Point

1

Improved installation workability

Increased freedom of a piping layout

Up

Point

2

Compact and modern design

Height

210mm

Right

Rear

The refrigerant pipe from the unit can be arranged in three directions, rear, right and up. The drain pipe can be arranged in two directions, left and right. This will allow a free layout of piping for various installation conditions. The unit can only be serviced from the bottom.

All models fit compactly on ceiling. (Height-210mm or 250mm).

Plain, modern design featuring rounded edges gives room a comfortable atmosphere.

FDEN40VD, 50VD weights 30kg the lightest level in the industry.

Convenient and quick installation.

18

Outline drawing (Unit:mm)

24 a (Suspension bolts pitch)

40

Drain hole connection(1)

(VP20(I.D.20))

76

Air inlet grille b c

Gas piping

(VP20(I.D.20))

24

290(Suspension bolts pitch)

135

68

410

Holes for suspension bolts

(M8 to M10X 4pcs.Not included)

145

52

Liquid piping

Gas piping

40

Air outlet

Indication board

690

195

235

271

Note(1) The slope of drain piping

inside the unit is able

to take incline of 10mm.

(VP20 (I.D.20))

75

110

135

Liquid piping

Space for installation and service

100 or more or more 150 or more

Obstacles

5 or more

Dimension Table model

FDEN40,50

FDEN60,71

FDEN100~140 a

1022

1272

1572 b

990

1240

1540 c

1070

1320

1620 d

215

215

255 e

210

210

250

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Energy label

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

Air flow

1

Exterior dimensions

Net weight

Indoor

Outdoor

Indoor

Outdoor

Height x Width x Depth

Range of usage

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN40ZIXVD

FDEN40VD

SRC40ZIX-S

FDEN50ZIXVD

FDEN50VD

SRC50ZIX-S

FDEN60ZIXVD

FDEN60VD

SRC60ZIX-S

FDEN71VNXVD

FDEN71VD

FDC71VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDEN100VNXVD

FDEN100VD

FDC100VNX

4.0

(1.8~4.7)

4.5

(2.0~5.4)

5.0

(2.2~5.6)

5.4

(2.5~6.3)

5.6

(2.8~6.3)

6.7

(3.1~7.1)

7.1

(3.2~8.0)

8.0

(3.6~9.0)

10.0

(4.0~11.2)

11.2

(4.0~12.5)

1.04/1.13

3.85/3.98

A/A

5(12)

1.59/1.58

3.14/3.42

B/B

1.95/2.12

2.87/3.16

C/D

2.11/2.11

3.36/3.79

A/A

2.80/2.88

3.57/3.89

A/A

Hi:39 Me:38 Lo:37

47

Hi:11 Me:9 Lo:7

210x1,070x690

28

40

5(14)

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

640x800(+71)x290

43

750x880(+88)x340

60

5(24)

48

Hi:41 Me:39 Lo:38 Hi:44 Me:41 Lo:39

Cooling:51 Heating:48 Cooling:48 Heating:50

Hi:18 Me:14 Lo:12 Hi:18 Me:14 Lo:12 Hi:26 Me:23 Lo:21

Cooling:60 Heating:50

210x1,320x690

37

5(17)

100

250x1,620x690

49

1,300x970x370

105

Scroll

1.4(15)

6.35/12.7

30

20

20

2.95(30)

Rotary

9.52/15.88

50

30

15

4.5(30)

-15~43* 2

-15~20 -20~20

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDEN125VNXVD

FDEN125VD

FDC125VNX

FDEN140VNXVD

FDEN140VD

FDC140VNX

FDEN100VSXVD

FDEN100VD

FDC100VSX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDEN125VSXVD

FDEN125VD

FDC125VSX

FDEN140VSXVD

FDEN140VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

Nominal cooling capacity

(Min~Max)

ISO-T1(JIS)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor

Outdoor

Air flow

Exterior dimensions

Net weight

Air filter, Q'ty

Indoor

Outdoor

Height x Width x Depth

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Range of usage

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

12.5

(5.0~14.0)

14.0

(4.0~17.0)

14.0

(5.0~16.0)

16.0

(4.0~18.0)

10.0

(4.0~11.2)

11.2

(4.0~16.0)

12.5

(5.0~14.0)

14.0

(4.0~18.0)

14.0

(5.0~16.0)

16.0

(4.0~20.0)

3.86/3.77

3.24/3.71

A/A

5(26)

4.98/4.69

2.81/3.41

Hi:46 Me:44 Lo:43

Cooling:48 Heating:50 Cooling:49 Heating:52

Hi:29 Me:26 Lo:23

C/B

2.80/2.88

3.57/3.89

A/A

Hi:44 Me:41 Lo:39

Cooling:48 Heating:50

Hi:26 Me:23 Lo:21

100

250x1,620x690

49

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

1,300x970x370

105

3.86/3.77

3.24/3.71

4.98/4.69

2.81/3.41

A/A

5(15)

C/B

Hi:46 Me:44 Lo:43

Cooling:48 Heating:50 Cooling:49 Heating:52

Hi:29 Me:26 Lo:23

100

Rotary

4.5(30)

9.52/15.88

50

30

15

-15~43* 2

-20~20

100

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB.

Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 40/50ZIXVD 46dB, 60ZIXVD 50dB, 71VNXVD 50dB, 100VNXVD 46dB, 125/140VNXVD 50dB, 100VSXVD 46dB, 125/140VSXVD 50dB

Air flow: 40/50ZIXVD 13CMM, 60ZIXVD 22CMM, 71VNXVD 22CMM, 100VNXVD 28CMM, 125/140VNXVD 32CMM, 100VSXVD 28CMM, 125/140VSXVD 32CMM

19

Micro Inverter

FDT

[ INDOOR UNIT ]

CEILING CASSETTE -4wayA

CLASS

Wired remote control

FDT 100/125/140VD

Wireless remote control

RC-E4

(Option)

RCH-E3

(Option)

RCN-T-36W-E

(Option)

20

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDT100VNVD

FDT100VD

FDC100VN

FDT125VNVD

FDT125VD

FDC125VN

FDT140VNVD

FDT140VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

Micro Inverter

FDT100VSVD

FDT100VD

FDC100VS

FDT125VSVD

FDT125VD

FDC125VS

FDT140VSVD

FDT140VD

FDC140VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel

*

1

Indoor

Outdoor kW kW kW

A dB(A) kg(m)

ø m m m

O/U

O/U

10.0

(4.0~11.2)

11.2

(4.0~12.5)

2.76/2.74

3.62/4.09

A/A

Hi:40

Me:37 Lo:35

49

Hi:27

Me:24 Lo:20

12.5

(5.0~14.0)

14.0

(4.0~16.0)

14.0

(5.0~14.5)

16.0

(4.0~16.5)

10.0

(4.0~11.2)

11.2

(4.0~12.5)

12.5

(5.0~14.0)

14.0

(4.0~16.0)

4.05/3.77

3.09/3.71

B/A

4.98/4.57

2.81/3.50

C/B

2.76/2.74

3.62/4.09

A/A

4.05/3.77

3.09/3.71

B/A

5(24)

Hi:42

Me:40 Lo:37

Cooling:50 Heating:51

Hi:30

Hi:43

Me:41 Lo:38

51

Hi:30

Hi:40

Me:37 Lo:35

49

Me:27 Lo:23

Cooling:75 Heating:73

Me:27 Lo:23

Hi:27

Me:24 Lo:20

Unit:298x840x840 Panel:35x950x950

32.5(Unit:27 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

845x970x370

5(15)

Hi:42

Me:40 Lo:37

Cooling:50 Heating:51

Hi:30

Me:27 Lo:23

Cooling:75 Heating:73

81 83

Rotary

3.8(30)

9.52/15.88

50

30

15

-15~43* 2

-20~20

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.98/4.57

2.81/3.50

C/B

Hi:43

Me:41 Lo:38

51

Hi:30

Me:27 Lo:23 Air flow

Indoor

Exterior dimensions

Net weight

Panel

Air filter, Q'ty

Outdoor

Height x Width x Depth

Unit+Panel

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Liquid/Gas

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating

CMM mm kg mm kg

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100/125/140VNVD 51dB, 100/125/140VSVD 51dB

Air flow: 100/125/140VNVD 37CMM, 100/125/140VSVD 37CMM

COP

DUCT CONNECTED -High Static pressure-

FDU

SPECIFICATIONS

Set model name

Indoor name

FDU 100/125/140VD

FDU 200/250VD

Fan control kit

(100~200Pa)

U-FCRA

[For 200/250VD]

(option)

Wired remote control

RC-E4

(Option)

RCH-E3

(Option)

Wireless remote control

RCN-KIT3-E

(Option)

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1 Indoor

Outdoor

Air flow

Indoor

Outdoor

External static pressure

Exterior dimensions Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Range of usage

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption Cooling/Heating

Cooling/Heating

Energy label

Inrush current (Max. running current)

Sound Ievel*

1

Cooling/Heating

Indoor

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor

Outdoor

External static pressure * 2

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Liquid/Gas

O/U is higher

Range of usage difference

Operating temperature range

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

* FDU140VNVD

FDU140VD

FDC140VN

1Phase

220-240V 50Hz

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.95/4.43

2.83/3.61

C/A

5(28)

Hi:43 Lo:38

51

Hi:42 Lo:33.5

81

* FDU100VSVD

FDU100VD

FDC100VS

Micro Inverter

* FDU125VSVD

FDU125VD

FDC125VS

3Phase 380-415V 50Hz kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

* FDU140VSVD

FDU140VD

FDC140VS

* Not available in 60Hz

Micro Inverter

* FDU100VNVD

FDU100VD

FDC100VN

* FDU125VNVD

FDU125VD

FDC125VN

1Phase 220-240V 50Hz

10.0

12.5

(4.0~11.2) (5.0~14.0)

11.2

(4.0~12.5)

14.0

(4.0~16.0)

2.88/2.99

3.47/3.75

A/A

5(25)

Hi:42 Lo:37

49

4.04/3.79

3.09/3.69

B/A

5(27)

Hi:43 Lo:38

Cooling:50 Heating:51

Hi:34 Lo:27 Hi:42 Lo:33.5

Cooling:75 Heating:73

Standard:50, Max:130

350x1,370x650

63

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

845x970x370

81

Rotary

3.8(30)

9.52/15.88

50

30

15

-15~43* 3 -15~43* 2

-20~20

FDU200VSVD

FDU200VD

FDC200VS

A

CLASS

FDU250VSVD

FDU250VD

FDC250VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

20.0

(7.0~22.4)

25.0

(10.0~28.0)

11.2

(4.0~12.5)

14.0

(4.0~16.0)

16.0

(4.0~16.5)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

2.88/2.99

3.47/3.75

A/A

5(16)

Hi:42 Lo:37

49

4.04/3.79

3.09/3.69

350x1,370x650

B/A

5(18)

Hi:34 Lo:27

Cooling:75 Heating:73

Standard:50, Max:130

Hi:43 Lo:38

Cooling:50 Heating:51

4.95/4.43

2.83/3.61

Hi:42 Lo:33.5

C/A

5(19)

51

63

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

50Hz:6.59/6.08

60Hz:6.58/5.84

50Hz:3.03/3.68

60Hz:3.04/3.83

B/A

5(24)

51

57

50Hz: 9.91/8.50

60Hz:10.21/8.22

50Hz:2.52/3.29

60Hz:2.45/3.41

50Hz:E/C 60Hz:E/B

5(27)

52

Cooling:57 Heating:58

50Hz:51, 60Hz:60 50Hz:68, 60Hz:80

Cooling:150 Heating:145

Standard:100, Max:200

360x1,570x830

92

845x970x370 1,300x970x370

83 122 140

Rotary

3.8(30)

9.52/15.88

50

5.4(30)

9.52/25.4

Scroll

70

7.2(30)

12.7/25.4

30

15

-15~43 * 3

-20~20 -15~20

*

*

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of FDU100/125/140 is 60Pa and that of FDU200/250 is 100Pa.

1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

*

2 : External static pressure is changeable to be set by the remote control. Standard external static pressure is factory setting. MAX external static pressure is ''High static pressure'' setting. The values of sound pressure level become 5dB(A) higher at eternal static pressure of 130Pa.

3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

21

Micro Inverter

FDT

[ INDOOR UNIT ]

CEILING CASSETTE -4wayA

CLASS

Wired remote control

FDT 100/125/140VD

Wireless remote control

RC-E4

(Option)

RCH-E3

(Option)

RCN-T-36W-E

(Option)

20

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

FDT100VNVD

FDT100VD

FDC100VN

FDT125VNVD

FDT125VD

FDC125VN

FDT140VNVD

FDT140VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

Micro Inverter

FDT100VSVD

FDT100VD

FDC100VS

FDT125VSVD

FDT125VD

FDC125VS

FDT140VSVD

FDT140VD

FDC140VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel

*

1

Indoor

Outdoor kW kW kW

A dB(A) kg(m)

ø m m m

O/U

O/U

10.0

(4.0~11.2)

11.2

(4.0~12.5)

2.76/2.74

3.62/4.09

A/A

Hi:40

Me:37 Lo:35

49

Hi:27

Me:24 Lo:20

12.5

(5.0~14.0)

14.0

(4.0~16.0)

14.0

(5.0~14.5)

16.0

(4.0~16.5)

10.0

(4.0~11.2)

11.2

(4.0~12.5)

12.5

(5.0~14.0)

14.0

(4.0~16.0)

4.05/3.77

3.09/3.71

B/A

4.98/4.57

2.81/3.50

C/B

2.76/2.74

3.62/4.09

A/A

4.05/3.77

3.09/3.71

B/A

5(24)

Hi:42

Me:40 Lo:37

Cooling:50 Heating:51

Hi:30

Hi:43

Me:41 Lo:38

51

Hi:30

Hi:40

Me:37 Lo:35

49

Me:27 Lo:23

Cooling:75 Heating:73

Me:27 Lo:23

Hi:27

Me:24 Lo:20

Unit:298x840x840 Panel:35x950x950

32.5(Unit:27 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

845x970x370

5(15)

Hi:42

Me:40 Lo:37

Cooling:50 Heating:51

Hi:30

Me:27 Lo:23

Cooling:75 Heating:73

81 83

Rotary

3.8(30)

9.52/15.88

50

30

15

-15~43* 2

-20~20

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.98/4.57

2.81/3.50

C/B

Hi:43

Me:41 Lo:38

51

Hi:30

Me:27 Lo:23 Air flow

Indoor

Exterior dimensions

Net weight

Panel

Air filter, Q'ty

Outdoor

Height x Width x Depth

Unit+Panel

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Liquid/Gas

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating

CMM mm kg mm kg

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100/125/140VNVD 51dB, 100/125/140VSVD 51dB

Air flow: 100/125/140VNVD 37CMM, 100/125/140VSVD 37CMM

COP

DUCT CONNECTED -High Static pressure-

FDU

SPECIFICATIONS

Set model name

Indoor name

FDU 100/125/140VD

FDU 200/250VD

Fan control kit

(100~200Pa)

U-FCRA

[For 200/250VD]

(option)

Wired remote control

RC-E4

(Option)

RCH-E3

(Option)

Wireless remote control

RCN-KIT3-E

(Option)

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1 Indoor

Outdoor

Air flow

Indoor

Outdoor

External static pressure

Exterior dimensions Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Range of usage

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption Cooling/Heating

Cooling/Heating

Energy label

Inrush current (Max. running current)

Sound Ievel*

1

Cooling/Heating

Indoor

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor

Outdoor

External static pressure * 2

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Liquid/Gas

O/U is higher

Range of usage difference

Operating temperature range

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

* FDU140VNVD

FDU140VD

FDC140VN

1Phase

220-240V 50Hz

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.95/4.43

2.83/3.61

C/A

5(28)

Hi:43 Lo:38

51

Hi:42 Lo:33.5

81

* FDU100VSVD

FDU100VD

FDC100VS

Micro Inverter

* FDU125VSVD

FDU125VD

FDC125VS

3Phase 380-415V 50Hz kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

* FDU140VSVD

FDU140VD

FDC140VS

* Not available in 60Hz

Micro Inverter

* FDU100VNVD

FDU100VD

FDC100VN

* FDU125VNVD

FDU125VD

FDC125VN

1Phase 220-240V 50Hz

10.0

12.5

(4.0~11.2) (5.0~14.0)

11.2

(4.0~12.5)

14.0

(4.0~16.0)

2.88/2.99

3.47/3.75

A/A

5(25)

Hi:42 Lo:37

49

4.04/3.79

3.09/3.69

B/A

5(27)

Hi:43 Lo:38

Cooling:50 Heating:51

Hi:34 Lo:27 Hi:42 Lo:33.5

Cooling:75 Heating:73

Standard:50, Max:130

350x1,370x650

63

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

845x970x370

81

Rotary

3.8(30)

9.52/15.88

50

30

15

-15~43* 3 -15~43* 2

-20~20

FDU200VSVD

FDU200VD

FDC200VS

A

CLASS

FDU250VSVD

FDU250VD

FDC250VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

20.0

(7.0~22.4)

25.0

(10.0~28.0)

11.2

(4.0~12.5)

14.0

(4.0~16.0)

16.0

(4.0~16.5)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

2.88/2.99

3.47/3.75

A/A

5(16)

Hi:42 Lo:37

49

4.04/3.79

3.09/3.69

350x1,370x650

B/A

5(18)

Hi:34 Lo:27

Cooling:75 Heating:73

Standard:50, Max:130

Hi:43 Lo:38

Cooling:50 Heating:51

4.95/4.43

2.83/3.61

Hi:42 Lo:33.5

C/A

5(19)

51

63

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

50Hz:6.59/6.08

60Hz:6.58/5.84

50Hz:3.03/3.68

60Hz:3.04/3.83

B/A

5(24)

51

57

50Hz: 9.91/8.50

60Hz:10.21/8.22

50Hz:2.52/3.29

60Hz:2.45/3.41

50Hz:E/C 60Hz:E/B

5(27)

52

Cooling:57 Heating:58

50Hz:51, 60Hz:60 50Hz:68, 60Hz:80

Cooling:150 Heating:145

Standard:100, Max:200

360x1,570x830

92

845x970x370 1,300x970x370

83 122 140

Rotary

3.8(30)

9.52/15.88

50

5.4(30)

9.52/25.4

Scroll

70

7.2(30)

12.7/25.4

30

15

-15~43 * 3

-20~20 -15~20

*

*

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of FDU100/125/140 is 60Pa and that of FDU200/250 is 100Pa.

1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

*

2 : External static pressure is changeable to be set by the remote control. Standard external static pressure is factory setting. MAX external static pressure is ''High static pressure'' setting. The values of sound pressure level become 5dB(A) higher at eternal static pressure of 130Pa.

3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

21

Micro Inverter [ INDOOR UNIT ]

DUCT CONNECTED -Low/Middle Static pressure-

FDUM

A

CLASS external static pressure loss:5pa

Wired remote control

FDUM 100/125/140VD

Filter kit

UM-FL3E : for 100, 125, 140

(option)

Wireless remote control

22

RC-E4

(Option)

RCH-E3

(Option)

RCN-KIT3-E

(Option)

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1 Indoor

Outdoor

Air flow

Indoor

Outdoor

Static pressure

Exterior dimensions

Net weight

Air filter, Q'ty

Height x Width x Depth

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Liquid/Gas

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

Micro Inverter

FDUM100VNVD

FDUM100VD

FDC100VN

FDUM125VNVD

FDUM125VD

FDC125VN

FDUM140VNVD

FDUM140VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

FDUM100VSVD

FDUM100VD

FDC100VS

FDUM125VSVD

FDUM125VD

FDC125VS

FDUM140VSVD

FDUM140VD

FDC140VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

11.2

(4.0~12.5)

50Hz:2.80/2.77

60Hz:2.80/2.80

50Hz:3.57/4.04

60Hz:3.57/4.00

A/A

Hi:37 Me:35 Lo:32

49

Standard:60, Max:90/100

14.0

(4.0~16.0)

50Hz:4.03/3.80

60Hz:4.03/3.85

50Hz:3.10/3.68

60Hz:3.10/3.64

16.0

(4.0~16.5)

50Hz:4.95/4.89

60Hz:4.95/4.91

50Hz:2.83/3.27

60Hz:2.83/3.26

C/C

11.2

(4.0~12.5)

50Hz:2.80/2.77

60Hz:2.80/2.80

50Hz:3.57/4.04

60Hz:3.57/4.00

A/A B/A

5(24)

Hi: 38 Me:36 Lo:33

Cooling:50 Heating:51 51

Hi: 37 Me:35 Lo:32

49

Hi:28 Me:25 Lo:22

Cooling:75 Heating:73

Standard:60/55, Max:85/100 Standard:60, Max:90/100

350x1,370x635

59

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

845x970x370

14.0

(4.0~16.0)

16.0

(4.0~16.5)

50Hz:4.03/3.80

60Hz:4.03/3.85

50Hz:3.10/3.68

60Hz:3.10/3.64

50Hz:4.95/4.89

60Hz:4.95/4.91

50Hz:2.83/3.27

60Hz:2.83/3.26

C/C B/A

5(15)

Hi: 38 Me:36 Lo:33

Cooling:50 Heating:51 51

Standard:60/55, Max:85/100

81 83

Rotary

3.8(30)

9.52/15.88

50

30

15

-15~43* 2

-20~20

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of indoor units is 60Pa.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100/125/140VNVD 41dB, 100/125/140VSVD 41dB

Air flow: 100/125/140VNVD 34CMM, 100/125/140VSVD 34CMM

CEILING SUSPENDED

FDEN

A

CLASS

Wired remote control

FDEN 100/125/140VD

Wireless remote control

RC-E4

(Option)

RCH-E3

(Option)

RCN-E1R

(Option)

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Energy label

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor

Outdoor

Air flow

Indoor

Exterior dimensions

Outdoor

Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Type of compressor

Ref.amount precharged

Liquid/Gas

Range of usage

Ref.piping size

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

Micro Inverter

FDEN100VNVD

FDEN100VD

10.0

(4.0~11.2)

11.2

(4.0~12.5)

FDEN125VNVD

FDEN125VD

FDC100VN FDC125VN FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(4.0~16.0)

FDEN140VNVD

FDEN140VD

14.0

(5.0~14.5)

16.0

(4.0~16.5)

FDEN100VSVD

FDEN100VD

FDC100VS FDC125VS FDC140VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

11.2

(4.0~12.5)

FDEN125VSVD

FDEN125VD

12.5

(5.0~14.0)

14.0

(4.0~16.0)

FDEN140VSVD

FDEN140VD

14.0

(5.0~14.5)

16.0

(4.0~16.5)

2.85/2.97

3.51/3.77

A/A

Hi:44

Me:41 Lo:39

49

Hi:26

Me:23 Lo:21

4.45/4.08

2.80/3.43

C/B

5(24)

5.80/4.92

2.41/3.25

E/C

2.85/2.97

3.51/3.77

A/A

Hi:46 Me:44 Lo:43

Hi:44

Me:41 Lo:39

Cooling:50 Heating:51 51 49

Hi:26

Hi:29 Me:26 Lo:23

Me:23 Lo:21

Cooling:75 Heating:73

250x1,620x690

49

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

845x970x370

4.45/4.08

2.80/3.43

C/B

5(15)

Hi:46 Me:44 Lo:43

Cooling:50 Heating:51

5.80/4.92

2.41/3.25

Hi:29 Me:26 Lo:23

E/C

51

81 83

Rotary

3.8(30)

9.52/15.88

50

30

15

-15~43* 2

-20~20

*

*

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB.

Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100VNVD 46dB, 125/140VNVD 50dB, 100VSVD 46dB, 125/140VSVD 50dB

Air flow: 100VNVD 28CMM, 125/140VNVD 32CMM, 100VSVD 28CMM, 125/140VSVD 32CMM

23

Micro Inverter [ INDOOR UNIT ]

DUCT CONNECTED -Low/Middle Static pressure-

FDUM

A

CLASS external static pressure loss:5pa

Wired remote control

FDUM 100/125/140VD

Filter kit

UM-FL3E : for 100, 125, 140

(option)

Wireless remote control

22

RC-E4

(Option)

RCH-E3

(Option)

RCN-KIT3-E

(Option)

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1 Indoor

Outdoor

Air flow

Indoor

Outdoor

Static pressure

Exterior dimensions

Net weight

Air filter, Q'ty

Height x Width x Depth

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Type of compressor

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Liquid/Gas

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM

Pa mm kg mm kg kg(m)

ø m m m

O/U

O/U

Micro Inverter

FDUM100VNVD

FDUM100VD

FDC100VN

FDUM125VNVD

FDUM125VD

FDC125VN

FDUM140VNVD

FDUM140VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

FDUM100VSVD

FDUM100VD

FDC100VS

FDUM125VSVD

FDUM125VD

FDC125VS

FDUM140VSVD

FDUM140VD

FDC140VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

11.2

(4.0~12.5)

50Hz:2.80/2.77

60Hz:2.80/2.80

50Hz:3.57/4.04

60Hz:3.57/4.00

A/A

Hi:37 Me:35 Lo:32

49

Standard:60, Max:90/100

14.0

(4.0~16.0)

50Hz:4.03/3.80

60Hz:4.03/3.85

50Hz:3.10/3.68

60Hz:3.10/3.64

16.0

(4.0~16.5)

50Hz:4.95/4.89

60Hz:4.95/4.91

50Hz:2.83/3.27

60Hz:2.83/3.26

C/C

11.2

(4.0~12.5)

50Hz:2.80/2.77

60Hz:2.80/2.80

50Hz:3.57/4.04

60Hz:3.57/4.00

A/A B/A

5(24)

Hi: 38 Me:36 Lo:33

Cooling:50 Heating:51 51

Hi: 37 Me:35 Lo:32

49

Hi:28 Me:25 Lo:22

Cooling:75 Heating:73

Standard:60/55, Max:85/100 Standard:60, Max:90/100

350x1,370x635

59

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

845x970x370

14.0

(4.0~16.0)

16.0

(4.0~16.5)

50Hz:4.03/3.80

60Hz:4.03/3.85

50Hz:3.10/3.68

60Hz:3.10/3.64

50Hz:4.95/4.89

60Hz:4.95/4.91

50Hz:2.83/3.27

60Hz:2.83/3.26

C/C B/A

5(15)

Hi: 38 Me:36 Lo:33

Cooling:50 Heating:51 51

Standard:60/55, Max:85/100

81 83

Rotary

3.8(30)

9.52/15.88

50

30

15

-15~43* 2

-20~20

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of indoor units is 60Pa.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100/125/140VNVD 41dB, 100/125/140VSVD 41dB

Air flow: 100/125/140VNVD 34CMM, 100/125/140VSVD 34CMM

CEILING SUSPENDED

FDEN

A

CLASS

Wired remote control

FDEN 100/125/140VD

Wireless remote control

RC-E4

(Option)

RCH-E3

(Option)

RCN-E1R

(Option)

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Energy label

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor

Outdoor

Air flow

Indoor

Exterior dimensions

Outdoor

Height x Width x Depth

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Type of compressor

Ref.amount precharged

Liquid/Gas

Range of usage

Ref.piping size

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

Micro Inverter

FDEN100VNVD

FDEN100VD

10.0

(4.0~11.2)

11.2

(4.0~12.5)

FDEN125VNVD

FDEN125VD

FDC100VN FDC125VN FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(4.0~16.0)

FDEN140VNVD

FDEN140VD

14.0

(5.0~14.5)

16.0

(4.0~16.5)

FDEN100VSVD

FDEN100VD

FDC100VS FDC125VS FDC140VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

11.2

(4.0~12.5)

FDEN125VSVD

FDEN125VD

12.5

(5.0~14.0)

14.0

(4.0~16.0)

FDEN140VSVD

FDEN140VD

14.0

(5.0~14.5)

16.0

(4.0~16.5)

2.85/2.97

3.51/3.77

A/A

Hi:44

Me:41 Lo:39

49

Hi:26

Me:23 Lo:21

4.45/4.08

2.80/3.43

C/B

5(24)

5.80/4.92

2.41/3.25

E/C

2.85/2.97

3.51/3.77

A/A

Hi:46 Me:44 Lo:43

Hi:44

Me:41 Lo:39

Cooling:50 Heating:51 51 49

Hi:26

Hi:29 Me:26 Lo:23

Me:23 Lo:21

Cooling:75 Heating:73

250x1,620x690

49

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

845x970x370

4.45/4.08

2.80/3.43

C/B

5(15)

Hi:46 Me:44 Lo:43

Cooling:50 Heating:51

5.80/4.92

2.41/3.25

Hi:29 Me:26 Lo:23

E/C

51

81 83

Rotary

3.8(30)

9.52/15.88

50

30

15

-15~43* 2

-20~20

*

*

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB.

Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

2 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100VNVD 46dB, 125/140VNVD 50dB, 100VSVD 46dB, 125/140VSVD 50dB

Air flow: 100VNVD 28CMM, 125/140VNVD 32CMM, 100VSVD 28CMM, 125/140VSVD 32CMM

23

MULTI SYSTEM

Up to Four indoor units can be connected to a single outdoor unit and simultaneously operated with a single remote control.

Twin / Triple / Double Twin Multi System

By referring to the following table for applicable indoor units, select the same models and capacities.

Applicable indoor units

Capacity

Model

4way

4way compact

(600 x 600mm)

Low/Middle Static pressure

Ceiling Suspended

Wall Mounted

Only used with outdoor units of Multi System

Combination of indoor units

Micro Inverter

NEW

Combination

FDC71VNX

40 + 40

FDC100VNX

FDC100VSX

50 + 50

FDC125VNX

FDC125VSX

60 + 60

FDC140VNX

FDC140VSX

71 + 71

50 + 50 + 50

FDC100VNV

FDC100VSV

50 + 50

FDC125VNV

FDC125VSV

60 + 60

FDC140VNV

FDC140VSV FDC200VSV FDC250VSV

71 + 71

50 + 50 + 50

100 + 100

71 + 71 + 71

125 + 125

50+50+50+50 60+60+60+60

Decision of piping specification

Diagrams below show the application as samples. For further information, refer to TECHNICAL MANUAL.

24

Twin type

Models FDC71VNX, FDC100~140VNV/VSV

[Branch pipe set : DIS-WA1]

Indoor unit

Outdoor unit

Gas line

4

3

1 2

L

Liquid line

4

(Example)

Item

Model

FDC71

FDC100

FDC125

FDC140

Indoor unit combinations

40+40

50+50

60+60

71+71

Liquid pipe

Main pipe Branch pipe

ø9.52Xt0.8 ø9.52Xt0.8

Gas pipe

Main pipe

ø15.88Xt1.0

Branch pipe

ø12.7Xt0.8

ø15.88Xt1.0

Notes (1) When 40-60 models of indoor units are applied to this combination, the reducer 3 supplied with the branch piping set should be used in order to reduce the liquid piping size from ø9.52mm to ø6.35mm at indoor unit side

(2)

(flare connection). Accordingly be sure to select the liquid piping size

ø9.52mm from branch to indoor unit.

The reducer 4 is for FDC71 and 100 models only.

3

Gas pipe

ID15.88

Symbol Liquid pipe

ID9.52

Symbol Reducer

Chart of shapes of branch piping parts

(DIS-WA1)

ID15.88

11

1

8

ID9.52

2

ID9.52

8

24 ID15.88

210

ID9.52

Notes (1)

(2)

Symbol 1 to 4 in the drawing shows the symbols of branch piping parts in the chart respectively.

Branch piping should always be arranged to have level or perpendicular position.

105

50

ø6.35 flared nut

2 piece

Symbol

3

Reducer

OD15.88

80

ID12.7

10

2 piece

Symbol

4

The branch piping (both gas and liquid lines) should always be arranged to have a level or perpendicular position.

2-Way Branch

Mount sections level with the floor.

Floor

3-Way Branch

Floor

Floor

Mount sections perpendicular to the floor.

Floor

Floor

Floor

Ideal for the installation in large area and L-shaped rooms, the V

Multi System has an extensive degree of flexibility in the selection of indoor units. Specifically, the selection of indoor units with different capacities in different types can be made.

V Multi System

Different models and capacities can be selected.

Applicable indoor units

Capacity

Model

4way

Ceiling Suspended

Combination of indoor units

NEW

Micro Inverter

FDC71VNX

40 + 40

FDC100VNX

FDC100VSX

FDC100VNV

FDC100VSV

50 + 50

FDC125VNX

FDC125VSX

FDC125VNV

FDC125VSV

60 + 60

50 + 71

FDC140VNX

FDC140VSX

FDC140VNV

FDC140VSV

71 + 71

50 + 50 + 50

FDC200VSV FDC250VSV

100 + 100

71 + 125

71 + 71 + 71

125 + 125

60 + 60 + 125

71 + 71 + 100

50+50+50+50 60+60+60+60

Triple type

Model FDC140VNV/VSV

[Branch pipe set : DIS-TA1]

The indoor_outdoor piping length differences among indoor units are less than 3m.

Indoor unit

(Example)

Item

Model

Indoor unit combinations

Liquid pipe

Main pipe Branch pipe Main pipe

Gas pipe

Branch pipe

FDC140 50+50+50 ø9.52Xt0.8

ø9.52Xt0.8

ø15.88Xt1.0

ø12.7Xt0.8

3

Outdoor unit

Gas line

1

Notes (1) The reducer 3 supplied with the branch piping set should be used in order to reduce the liquid piping size from ø9.52mm to ø6.35mm at indoor unit side (flare connection). Accordingly be sure to select the liquid piping size ø9.52mm from branch to indoor unit.

L

Liquid line

2

3

3

Gas pipe

100 80 80

ID12.7x3

Symbol Liquid pipe

100

ID9.52x3

Symbol Reducer

Chart of shapes of branch piping parts

(DIS-TA1) ID15.88

1

ID9.52

14

2 ID9.52

8

10

300

8

237

8

Notes (1)

(2)

Symbol 1 to 3 in the drawing shows the symbols of branch piping parts in the chart respectively.

Branch piping should always be arranged to have level or perpendicular position.

105

50

ø6.35 flared nut

Symbol

3

25

MULTI SYSTEM

Up to Four indoor units can be connected to a single outdoor unit and simultaneously operated with a single remote control.

Twin / Triple / Double Twin Multi System

By referring to the following table for applicable indoor units, select the same models and capacities.

Applicable indoor units

Capacity

Model

4way

4way compact

(600 x 600mm)

Low/Middle Static pressure

Ceiling Suspended

Wall Mounted

Only used with outdoor units of Multi System

Combination of indoor units

Micro Inverter

NEW

Combination

Ideal for the installation in large area and L-shaped rooms, the V

Multi System has an extensive degree of flexibility in the selection of indoor units. Specifically, the selection of indoor units with different capacities in different types can be made.

V Multi System

Different models and capacities can be selected.

Applicable indoor units

Capacity

Model

4way

Ceiling Suspended

Combination of indoor units

NEW

FDC71VNX

40 + 40

FDC100VNX

FDC100VSX

50 + 50

FDC125VNX

FDC125VSX

60 + 60

FDC140VNX

FDC140VSX

71 + 71

50 + 50 + 50

FDC100VNV

FDC100VSV

50 + 50

FDC125VNV

FDC125VSV

60 + 60

FDC140VNV

FDC140VSV FDC200VSV FDC250VSV

71 + 71

50 + 50 + 50

100 + 100

71 + 71 + 71

125 + 125

50+50+50+50 60+60+60+60

Decision of piping specification

Diagrams below show the application as samples. For further information, refer to TECHNICAL MANUAL.

24

Twin type

Models FDC71VNX, FDC100~140VNV/VSV

[Branch pipe set : DIS-WA1]

Indoor unit

Outdoor unit

Gas line

4

3

1 2

L

Liquid line

4

(Example)

Item

Model

FDC71

FDC100

FDC125

FDC140

Indoor unit combinations

40+40

50+50

60+60

71+71

Liquid pipe

Main pipe Branch pipe

ø9.52Xt0.8 ø9.52Xt0.8

Gas pipe

Main pipe

ø15.88Xt1.0

Branch pipe

ø12.7Xt0.8

ø15.88Xt1.0

Notes (1) When 40-60 models of indoor units are applied to this combination, the reducer 3 supplied with the branch piping set should be used in order to reduce the liquid piping size from ø9.52mm to ø6.35mm at indoor unit side

(2)

(flare connection). Accordingly be sure to select the liquid piping size

ø9.52mm from branch to indoor unit.

The reducer 4 is for FDC71 and 100 models only.

3

Gas pipe

ID15.88

Symbol Liquid pipe

ID9.52

Symbol Reducer

Chart of shapes of branch piping parts

(DIS-WA1)

ID15.88

11

1

8

ID9.52

2

ID9.52

8

24 ID15.88

210

ID9.52

Notes (1)

(2)

Symbol 1 to 4 in the drawing shows the symbols of branch piping parts in the chart respectively.

Branch piping should always be arranged to have level or perpendicular position.

105

50

ø6.35 flared nut

2 piece

Symbol

3

Reducer

OD15.88

80

ID12.7

10

2 piece

Symbol

4

The branch piping (both gas and liquid lines) should always be arranged to have a level or perpendicular position.

2-Way Branch

Mount sections level with the floor.

Floor

3-Way Branch

Floor

Floor

Mount sections perpendicular to the floor.

Floor

Floor

Floor

Micro Inverter

FDC71VNX

40 + 40

FDC100VNX

FDC100VSX

FDC100VNV

FDC100VSV

50 + 50

FDC125VNX

FDC125VSX

FDC125VNV

FDC125VSV

60 + 60

50 + 71

FDC140VNX

FDC140VSX

FDC140VNV

FDC140VSV

71 + 71

50 + 50 + 50

FDC200VSV FDC250VSV

100 + 100

71 + 125

71 + 71 + 71

125 + 125

60 + 60 + 125

71 + 71 + 100

50+50+50+50 60+60+60+60

Triple type

Model FDC140VNV/VSV

[Branch pipe set : DIS-TA1]

The indoor_outdoor piping length differences among indoor units are less than 3m.

(Example)

Indoor unit Item

Model

Indoor unit combinations

Liquid pipe

Main pipe Branch pipe Main pipe

Gas pipe

Branch pipe

FDC140 50+50+50 ø9.52Xt0.8

ø9.52Xt0.8

ø15.88Xt1.0

ø12.7Xt0.8

3

Outdoor unit

Gas line

1

Notes (1) The reducer 3 supplied with the branch piping set should be used in order to reduce the liquid piping size from ø9.52mm to ø6.35mm at indoor unit side (flare connection). Accordingly be sure to select the liquid piping size ø9.52mm from branch to indoor unit.

Liquid line

L

2

3

3

Gas pipe

100 80 80

ID12.7x3

Symbol Liquid pipe

100

ID9.52x3

Symbol Reducer

Chart of shapes of branch piping parts

(DIS-TA1) ID15.88

1

ID9.52

14

2 ID9.52

8

10

300

8

237

8

Notes (1)

(2)

Symbol 1 to 3 in the drawing shows the symbols of branch piping parts in the chart respectively.

Branch piping should always be arranged to have level or perpendicular position.

105

50

ø6.35 flared nut

Symbol

3

25

MULTI [ INDOOR UNIT ]

CEILING CASSETTE -4way-

FDT

Wired remote control

RC-E4

(Option)

RCH-E3

(Option)

FDT 40/50/60/71/100/125VD

Wireless remote control

RCN-T-36W-E

(Option)

A

CLASS

The values are for simultaneous Multi operation.

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor* 2

Outdoor

Height x Width x Depth

Unit+Panel

Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDT71VNXPVD FDT100VNXPVD

Twin

FDT40VD

FDC71VNX

FDT50VD

FDC100VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

7.1

(3.2~8.0)

10.0

(4.0~11.2)

8.0

(3.6~9.0)

11.2

(4.0~12.5)

1.85/1.99

3.84/4.02

2.56/2.66

3.91/4.21

A/A A/A

5(17) 5(24)

Hi:33 Me:31 Lo:30

Cooling:51 Heating:48 Cooling:48 Heating:50

Hi:18 Me:16 Lo:14

Cooling:60 Heating:50 100

Unit:246x840x840 Panel:35x950x950

27.5(Unit:22 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

750x880(+88)x340

60

2.95(30)

1,300x970x370

9.52/15.88

105

4.5(30)

50 100

30

15

-15~43* 3

-20~20

SPECIFICATIONS The values are for simultaneous Multi operation.

26

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor* 2

Outdoor

Height x Width x Depth

Unit+Panel

Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDT125VNXPVD FDT140VNXPVD FDT140VNXTVD FDT100VSXPVD

FDT60VD

FDC125VNX

Twin

FDT71VD

FDC140VNX

Triple

FDT50VD

FDC140VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(5.0~16.0)

FDT50VD

FDC100VSX

FDT125VSXPVD

Twin

FDT60VD

FDC125VSX

FDT140VSXPVD

FDT71VD

FDC140VSX

FDT140VSXTVD

Triple

FDT50VD

FDC140VSX

10.0

(4.0~11.2)

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~14.5)

14.0

(5.0~14.5)

14.0

(4.0~17.0)

3.06/3.22

4.08/4.35

A/A

Hi:33 Me:31 Lo:30

Cooling:48 Heating:50

Hi:18 Me:16 Lo:14

16.0

(4.0~18.0)

3.88/3.70

3.61/4.32

A/A

29.5(Unit:24 Panel:5.5)

16.0

(4.0~18.0)

3.88/3.76

3.61/4.26

A/A

5(26)

Hi:35 Me:33 Lo:31 Hi:33 Me:31 Lo:30

Cooling:49 Heating:52

Hi:21 Me:19 Lo:17 Hi:18 Me:16 Lo:14

11.2

(4.0~16.0)

2.56/2.66

3.91/4.21

A/A

14.0

(4.0~18.0)

3.06/3.22

4.08/4.35

A/A

Hi:33 Me:31 Lo:30

Cooling:48 Heating:50

Hi:18 Me:16 Lo:14

100

5(15)

16.0

(4.0~20.0)

3.88/3.70

3.61/4.32

A/A

Hi:35 Me:33 Lo:31

Cooling:49 Heating:52

Hi:21 Me:19 Lo:17

Unit:246x840x840 Panel:35x950x950

27.5(Unit:22 Panel:5.5)

T-PSA-3AW-E

29.5(Unit:24 Panel:5.5)

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43* 3

-20~20

16.0

(4.0~20.0)

3.88/3.76

3.61/4.26

A/A

Hi:33 Me:31 Lo:30

Hi:18 Me:16 Lo:14

27.5(Unit:22 Panel:5.5)

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 71/100VNXPVD 39dB, 100VSXPVD 39dB, 125/140VNXPVD 46dB, 125/140VSXPVD 46dB, 140VNXTVD 39dB,

140VSXTVD 39dB

Air flow: 71/100VNXPVD 20CMM, 100VSXPVD 20CMM, 125/140VNXPVD 28CMM, 125/140VSXPVD 28CMM, 140VNXTVD 20CMM, 140VSXTVD 20CMM

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Net weight

Ref.amount precharged

Ref.piping size

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

Indoor* 2

Outdoor

Exterior dimensions

Net weight

Panel

Air filter, Q'ty

Height x Width x Depth

Unit+Panel

Remote control(option)

Exterior dimensions

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg kg kg(m)

ø m m m

O/U

O/U

FDT100VNPVD

FDT50VD

FDC100VN

FDT125VNPVD

Twin

FDT60VD

FDC125VN

FDT140VNPVD

FDT71VD

FDC140VN

Micro Inverter

FDT140VNTVD

Triple

FDT50VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

14.0

(5.0~14.5)

FDT100VSPVD FDT125VSPVD

Twin

FDT140VSPVD

FDT50VD

FDC100VS

FDT60VD

FDC125VS

FDT71VD

FDC140VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

11.2

(4.0~12.5)

14.0

(4.0~16.0)

16.0

(4.0~16.5)

16.0

(4.0~16.5)

11.2

(4.0~12.5)

14.0

(4.0~16.0)

2.94/3.09

3.40/3.62

A/A

3.95/3.70

3.16/3.78

B/A

4.51/4.58

3.10/3.49

B/B

Hi:33

Me:31 Lo:30

49

Hi:33

Me:31 Lo:30

5(24)

Hi:35

Me:33 Lo:31

Cooling:50 Heating:51

Hi:18 Me:16 Lo:14

Hi:21

Me:19 Lo:17

4.65/4.63

3.01/3.46

B/B

2.94/3.09

3.40/3.62

A/A

3.95/3.70

3.16/3.78

B/A

5(15)

51

Hi:33

Me:31 Lo:30

Hi:18

Me:16 Lo:14

Cooling:75 Heating:73

Hi:33

Me:31 Lo:30

49

Hi:33

Me:31 Lo:30

Cooling:50 Heating:51

Hi:18 Me:16 Lo:14

27.5(Unit:22 Panel:5.5)

Unit:246x840x840 Panel:35x950x950

29.5(Unit:24 Panel:5.5) 27.5(Unit:22 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

845x970x370

81

3.8(30)

9.52/15.88

50

30

15

-15~43* 3

-20~20

16.0

(4.0~16.5)

4.51/4.58

3.10/3.49

B/B

Hi:35

Me:33 Lo:31

51

Hi:21

Me:19 Lo:17

29.5(Unit:24 Panel:5.5)

83

Powerful-Hi can be selected. Sound level: 100VNPVD 39dB, 125/140VNPVD 46dB, 140VNTVD 39dB, 100VSPVD 39dB, 125/140VSPVD 46dB

Air flow: 100VNPVD 20CMM, 125/140VNPVD 28CMM, 140VNTVD 20CMM, 100VSPVD 20CMM, 125/140VSPVD 28CMM

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Indoor* 2

Exterior dimensions

Net weight

Panel

Outdoor

Height x Width x Depth

Unit+Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Ref.amount precharged

Height x Width x Depth

Ref.piping size Liquid/Gas

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDT200VSPVD

Twin

FDT250VSPVD

FDT100VD

FDC200VS

FDT125VD

FDC250VS

20.0

(7.0~22.4)

25.0

(10.0~28.0)

Micro Inverter

FDT140VSTVD FDT200VSTVD

FDT50VD

FDC140VS

Triple

FDT71VD

FDC200VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

14.0

(5.0~14.5)

20.0

(7.0~22.4)

FDT200VSDVD

20.0

(7.0~22.4)

FDT250VSDVD

Double Twin

FDT50VD FDT60VD

FDC200VS FDC250VS

25.0

(10.0~28.0)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

16.0

(4.0~16.5)

22.4

(7.6~25.0)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

6.58/6.02

3.04/3.72

B/A

5(19)

Hi:40

Me:37 Lo:35

8.30/7.75

3.01/3.61

B/A

5(22)

Hi:42

Me:40 Lo:37

57

Hi:27

Cooling:57 Heating:58

Hi:30

Me:24 Lo:20 Me:27 Lo:23

Cooling:150 Heating:145

Unit:298x840x840 Panel:35x950x950

32.5(Unit:27 Panel:5.5)

4.65/4.63

3.01/3.46

B/B

5(15)

Hi:33

Me:31 Lo:30

51

Hi:18

Me:16 Lo:14

Cooling:75 Heating:73

6.49/6.12

3.08/3.66

B/A

5(19)

Hi:35

Me:33 Lo:31

57

Hi:21

Me:19 Lo:17

Cooling:150 Heating:145

6.58/6.15

3.04/3.64

B/A

5(19)

Hi:33

Me:31 Lo:30

57

8.28/7.70

3.02/3.64

B/A

5(22)

Hi:18

Me:16 Lo:14

Cooling:150 Heating:145

27.5(Unit:22 Panel:5.5)

Unit:246x840x840 Panel:35x950x950

29.5(Unit:24 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

27.5(Unit:22 Panel:5.5)

1,300x970x370

122

5.4(30)

9.52/22.22

70

140

7.2(30)

12.7/22.22

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

1,505x970x370 845x970x370

83

3.8(30)

9.52/15.88

50

1,300x970x370

122

5.4(30)

9.52/22.22

30

15

-15~43* 3

-15~20 -20~20

70

-15~20

Hi:33

Me:31 Lo:30

Cooling:57 Heating:58

29.5(Unit:24 Panel:5.5)

1,505x970x370

140

7.2(30)

12.7/22.22

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 200/250VSPVD 51dB, 140VSTVD 39dB, 200VSTVD 46dB, 200VSDVD 39dB, 250VSDVD 46dB

Air flow: 200/250VSPVD 37CMM, 140VSTVD 20CMM, 200VSTVD 28CMM, 200VSDVD 20CMM, 250VSDVD 28CMM

27

MULTI [ INDOOR UNIT ]

CEILING CASSETTE -4way-

FDT

Wired remote control

RC-E4

(Option)

RCH-E3

(Option)

FDT 40/50/60/71/100/125VD

Wireless remote control

RCN-T-36W-E

(Option)

A

CLASS

The values are for simultaneous Multi operation.

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor* 2

Outdoor

Height x Width x Depth

Unit+Panel

Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDT71VNXPVD FDT100VNXPVD

Twin

FDT40VD

FDC71VNX

FDT50VD

FDC100VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

7.1

(3.2~8.0)

10.0

(4.0~11.2)

8.0

(3.6~9.0)

11.2

(4.0~12.5)

1.85/1.99

3.84/4.02

2.56/2.66

3.91/4.21

A/A A/A

5(17) 5(24)

Hi:33 Me:31 Lo:30

Cooling:51 Heating:48 Cooling:48 Heating:50

Hi:18 Me:16 Lo:14

Cooling:60 Heating:50 100

Unit:246x840x840 Panel:35x950x950

27.5(Unit:22 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

750x880(+88)x340

60

2.95(30)

1,300x970x370

9.52/15.88

105

4.5(30)

50 100

30

15

-15~43* 3

-20~20

SPECIFICATIONS The values are for simultaneous Multi operation.

26

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor* 2

Outdoor

Height x Width x Depth

Unit+Panel

Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDT125VNXPVD FDT140VNXPVD FDT140VNXTVD FDT100VSXPVD

FDT60VD

FDC125VNX

Twin

FDT71VD

FDC140VNX

Triple

FDT50VD

FDC140VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(5.0~16.0)

FDT50VD

FDC100VSX

FDT125VSXPVD

Twin

FDT60VD

FDC125VSX

FDT140VSXPVD

FDT71VD

FDC140VSX

FDT140VSXTVD

Triple

FDT50VD

FDC140VSX

10.0

(4.0~11.2)

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~14.5)

14.0

(5.0~14.5)

14.0

(4.0~17.0)

3.06/3.22

4.08/4.35

A/A

Hi:33 Me:31 Lo:30

Cooling:48 Heating:50

Hi:18 Me:16 Lo:14

16.0

(4.0~18.0)

3.88/3.70

3.61/4.32

A/A

29.5(Unit:24 Panel:5.5)

16.0

(4.0~18.0)

3.88/3.76

3.61/4.26

A/A

5(26)

Hi:35 Me:33 Lo:31 Hi:33 Me:31 Lo:30

Cooling:49 Heating:52

Hi:21 Me:19 Lo:17 Hi:18 Me:16 Lo:14

11.2

(4.0~16.0)

2.56/2.66

3.91/4.21

A/A

14.0

(4.0~18.0)

3.06/3.22

4.08/4.35

A/A

Hi:33 Me:31 Lo:30

Cooling:48 Heating:50

Hi:18 Me:16 Lo:14

100

5(15)

16.0

(4.0~20.0)

3.88/3.70

3.61/4.32

A/A

Hi:35 Me:33 Lo:31

Cooling:49 Heating:52

Hi:21 Me:19 Lo:17

Unit:246x840x840 Panel:35x950x950

27.5(Unit:22 Panel:5.5)

T-PSA-3AW-E

29.5(Unit:24 Panel:5.5)

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43* 3

-20~20

16.0

(4.0~20.0)

3.88/3.76

3.61/4.26

A/A

Hi:33 Me:31 Lo:30

Hi:18 Me:16 Lo:14

27.5(Unit:22 Panel:5.5)

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 71/100VNXPVD 39dB, 100VSXPVD 39dB, 125/140VNXPVD 46dB, 125/140VSXPVD 46dB, 140VNXTVD 39dB,

140VSXTVD 39dB

Air flow: 71/100VNXPVD 20CMM, 100VSXPVD 20CMM, 125/140VNXPVD 28CMM, 125/140VSXPVD 28CMM, 140VNXTVD 20CMM, 140VSXTVD 20CMM

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Net weight

Ref.amount precharged

Ref.piping size

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

Indoor* 2

Outdoor

Exterior dimensions

Net weight

Panel

Air filter, Q'ty

Height x Width x Depth

Unit+Panel

Remote control(option)

Exterior dimensions

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg kg kg(m)

ø m m m

O/U

O/U

FDT100VNPVD

FDT50VD

FDC100VN

FDT125VNPVD

Twin

FDT60VD

FDC125VN

FDT140VNPVD

FDT71VD

FDC140VN

Micro Inverter

FDT140VNTVD

Triple

FDT50VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

14.0

(5.0~14.5)

FDT100VSPVD FDT125VSPVD

Twin

FDT140VSPVD

FDT50VD

FDC100VS

FDT60VD

FDC125VS

FDT71VD

FDC140VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

11.2

(4.0~12.5)

14.0

(4.0~16.0)

16.0

(4.0~16.5)

16.0

(4.0~16.5)

11.2

(4.0~12.5)

14.0

(4.0~16.0)

2.94/3.09

3.40/3.62

3.95/3.70

3.16/3.78

4.51/4.58

3.10/3.49

4.65/4.63

3.01/3.46

2.94/3.09

3.40/3.62

3.95/3.70

3.16/3.78

A/A

Hi:33

Me:31 Lo:30

49

B/A

Hi:33

Me:31 Lo:30

Hi:18 Me:16 Lo:14

5(24)

Cooling:50 Heating:51

B/B

Hi:35

Me:33 Lo:31

51

B/B

Hi:33

Me:31 Lo:30

Hi:21 Hi:18

Me:19 Lo:17 Me:16 Lo:14

Cooling:75 Heating:73

A/A

Hi:33

Me:31 Lo:30

49

B/A

5(15)

Hi:33

Me:31 Lo:30

Cooling:50 Heating:51

Hi:18 Me:16 Lo:14

27.5(Unit:22 Panel:5.5)

Unit:246x840x840 Panel:35x950x950

29.5(Unit:24 Panel:5.5) 27.5(Unit:22 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

845x970x370

81

3.8(30)

9.52/15.88

50

30

15

-15~43* 3

-20~20

16.0

(4.0~16.5)

4.51/4.58

3.10/3.49

B/B

Hi:35

Me:33 Lo:31

51

Hi:21

Me:19 Lo:17

29.5(Unit:24 Panel:5.5)

83

Powerful-Hi can be selected. Sound level: 100VNPVD 39dB, 125/140VNPVD 46dB, 140VNTVD 39dB, 100VSPVD 39dB, 125/140VSPVD 46dB

Air flow: 100VNPVD 20CMM, 125/140VNPVD 28CMM, 140VNTVD 20CMM, 100VSPVD 20CMM, 125/140VSPVD 28CMM

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Indoor* 2

Exterior dimensions

Net weight

Panel

Outdoor

Height x Width x Depth

Unit+Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Ref.amount precharged

Height x Width x Depth

Ref.piping size Liquid/Gas

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDT200VSPVD

Twin

FDT250VSPVD

FDT100VD

FDC200VS

FDT125VD

FDC250VS

20.0

(7.0~22.4)

25.0

(10.0~28.0)

Micro Inverter

FDT140VSTVD FDT200VSTVD

FDT50VD

FDC140VS

Triple

FDT71VD

FDC200VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

14.0

(5.0~14.5)

20.0

(7.0~22.4)

FDT200VSDVD FDT250VSDVD

Double Twin

FDT50VD FDT60VD

FDC200VS FDC250VS

20.0

(7.0~22.4)

25.0

(10.0~28.0)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

16.0

(4.0~16.5)

22.4

(7.6~25.0)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

6.58/6.02

3.04/3.72

B/A

5(19)

Hi:40

Me:37 Lo:35

8.30/7.75

3.01/3.61

B/A

5(22)

Hi:42

Me:40 Lo:37

57

Hi:27

Cooling:57 Heating:58

Hi:30

Me:24 Lo:20 Me:27 Lo:23

Cooling:150 Heating:145

Unit:298x840x840 Panel:35x950x950

32.5(Unit:27 Panel:5.5)

4.65/4.63

3.01/3.46

B/B

5(15)

Hi:33

Me:31 Lo:30

51

Hi:18

Me:16 Lo:14

Cooling:75 Heating:73

6.49/6.12

3.08/3.66

B/A

5(19)

Hi:35

Me:33 Lo:31

57

Hi:21

Me:19 Lo:17

Cooling:150 Heating:145

6.58/6.15

3.04/3.64

B/A

5(19)

Hi:33

Me:31 Lo:30

57

8.28/7.70

3.02/3.64

B/A

5(22)

Hi:18

Me:16 Lo:14

Cooling:150 Heating:145

27.5(Unit:22 Panel:5.5)

Unit:246x840x840 Panel:35x950x950

29.5(Unit:24 Panel:5.5)

T-PSA-3AW-E

Pocket Plastic net x1 (Washable)

27.5(Unit:22 Panel:5.5)

1,300x970x370

122

5.4(30)

9.52/22.22

70

140

7.2(30)

12.7/22.22

Wired:RC-E4, RCH-E3 Wireless:RCN-T-36W-E

1,505x970x370 845x970x370

83

3.8(30)

9.52/15.88

50

1,300x970x370

122

5.4(30)

9.52/22.22

30

15

-15~43* 3

-15~20 -20~20

70

-15~20

Hi:33

Me:31 Lo:30

Cooling:57 Heating:58

29.5(Unit:24 Panel:5.5)

1,505x970x370

140

7.2(30)

12.7/22.22

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 200/250VSPVD 51dB, 140VSTVD 39dB, 200VSTVD 46dB, 200VSDVD 39dB, 250VSDVD 46dB

Air flow: 200/250VSPVD 37CMM, 140VSTVD 20CMM, 200VSTVD 28CMM, 200VSDVD 20CMM, 250VSDVD 28CMM

27

MULTI [ INDOOR UNIT ]

CEILING CASSETTE -4way Compact (600 X 600mm)-

FDTC

A

CLASS

Wired remote control

FDTC 40/50/60VD

Wireless remote control

RC-E4

(Option)

RCH-E3

(Option)

RCN-TC-24W-ER

(Option)

SPECIFICATIONS The values are for simultaneous Multi operation.

28

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Indoor*

O/U is higher

O/U is lower

Cooling

Heating

2

Exterior dimensions

Net weight

Panel

Outdoor

Height x Width x Depth

Unit+Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDTC71VNXPVD

FDTC40VD

FDC71VNX

FDTC100VNXPVD

Twin

FDTC50VD

FDC100VNX

FDTC125VNXPVD

FDTC60VD

FDC125VNX

FDTC140VNXTVD

Triple

FDTC50VD

FDC140VNX

7.1

(3.2~8.0)

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

FDTC100VSXPVD

11.2

(4.0~16.0)

FDTC125VSXPVD FDTC140VSXTVD

FDTC50VD

FDC100VSX

Twin

FDTC60VD

FDC125VSX

Triple

FDTC50VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(4.0~18.0)

16.0

(4.0~20.0)

8.0

(3.6~9.0)

11.2

(4.0~12.5)

14.0

(4.0~17.0)

16.0

(4.0~18.0)

1.99/2.18

3.57/3.67

A/A

5(17)

Heating : Hi:42 Me:36 Lo:32

Cooling:51 Heating:48

2.78/3.02

3.60/3.71

A/A

5(24)

Cooling : Hi:42 Me:36 Lo:30

4.10/4.10

3.05/3.41

B/B

5(26)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

Cooling:48 Heating:50

4.34/4.34

3.23/3.69

A/A

2.78/3.02

3.60/3.71

A/A

4.10/4.10

3.05/3.41

B/B

Cooling : Hi:42 Me:36 Lo:30

5(15)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:42 Me:36 Lo:32

Cooling:49 Heating:52

Heating : Hi:46 Me:39 Lo:32

Cooling:48 Heating:50

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

Cooling:60 Heating:50

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

100

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

750x880(+88)x340

60

2.95(30)

Unit:248x570x570 Panel:35x700x700

18.5(Unit:15 Panel:3.5)

TC-PSA-25W-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-TC-24W-ER

1,300x970x370

105

4.5(30)

9.52/15.88

50 100

30

15

-15~43* 3

-20~20

4.34/4.34

3.23/3.69

A/A

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

Cooling:49 Heating:52

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 71/100/125VNXPVD 47dB, 100/125VSXPVD 47dB, 140VNXTVD 47dB, 140VSXTVD 47dB

Air flow: 71/100/125VNXPVD 13.5CMM, 100/125VSXPVD 13.5CMM, 140VNXTVD 13.5CMM, 140VSXTVD 13.5CMM

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Indoor*

O/U is higher

O/U is lower

Cooling

Heating

2

Outdoor

Exterior dimensions

Net weight

Panel

Air filter, Q'ty

Height x Width x Depth

Unit+Panel

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

Liquid/Gas kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDTC100VNPVD

FDTC50VD

FDC100VN

10.0

(4.0~11.2)

11.2

(4.0~12.5)

2.84/3.08

3.52/3.64

A/A

5(24)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

49

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

Micro Inverter

FDTC125VNPVD

Twin

FDTC60VD

FDC125VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(4.0~16.0)

5.35/4.62

2.34/3.03

F/D

5(27)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

Cooling:50 Heating:51

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

Cooling:75 Heating:73

Unit:248x570x570 Panel:35x700x700

18.5(Unit:15 Panel:3.5)

TC-PSA-25W-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-TC-24W-ER

845x970x370

81

3.8(30)

9.52/15.88

50

30

15

-15~43* 3

-20~20

Powerful-Hi can be selected. Sound level: 100/125VNPVD 47dB, 140VNTVD 47dB

Air flow: 100/125VNPVD 13.5CMM, 140VNTVD 13.5CMM

FDTC140VNTVD

Triple

FDTC50VD

FDC140VN

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.64/4.52

3.02/3.54

B/B

5(24)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

51

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Indoor* 2

Exterior dimensions

Net weight

Panel

Outdoor

Height x Width x Depth

Unit+Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Ref.amount precharged

Height x Width x Depth

Liquid/Gas Ref.piping size

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDTC100VSPVD

FDTC50VD

FDC100VS

10.0

(4.0~11.2)

11.2

(4.0~12.5)

2.84/3.08

3.52/3.64

A/A

5(15)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

49

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

Twin

FDTC125VSPVD

FDTC60VD

FDC125VS

Triple

FDTC50VD

FDC140VS

FDTC50VD

FDC200VS

12.5

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

(5.0~14.0)

14.0

(5.0~14.5)

20.0

(7.0~22.4)

14.0

(4.0~16.0)

Micro Inverter

FDTC140VSTVD

16.0

(4.0~16.5)

FDTC200VSDVD

22.4

(7.6~25.0)

FDTC250VSDVD

Double Twin

FDTC60VD

FDC250VS

25.0

(10.0~28.0)

28.0

(9.5~31.5)

5.35/4.62

2.34/3.03

F/D

5(15)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

Cooling:50 Heating:51

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

Cooling:75 Heating:73

4.64/4.52

3.02/3.54

7.33/6.98

2.73/3.21

11.28/10.19

2.22/2.75

B/B

5(15)

D/C

5(19)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

51 57

F/E

5(22)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

Cooling:57 Heating:58

Cooling : PHi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

Cooling:150 Heating:145

3.8(30)

9.52/15.88

50

Unit:248x570x570 Panel:35x700x700

18.5(Unit:15 Panel:3.5)

TC-PSA-25W-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-TC-24W-ER

845x970x370

83

1,300x970x370

122

5.4(30)

9.52/22.22

30

15

-15~43* 3

-20~20

70

-15~20

1,505x970x370

140

7.2(30)

12.7/22.22

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100/125VSPVD 47dB, 140VSTVD 47dB, 200/250VSDVD 47dB

Air flow: 100/125VSPVD 13.5CMM, 140VSTVD 13.5CMM, 200/250VSDVD 13.5CMM

29

MULTI [ INDOOR UNIT ]

CEILING CASSETTE -4way Compact (600 X 600mm)-

FDTC

A

CLASS

Wired remote control

FDTC 40/50/60VD

Wireless remote control

RC-E4

(Option)

RCH-E3

(Option)

RCN-TC-24W-ER

(Option)

SPECIFICATIONS The values are for simultaneous Multi operation.

28

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Indoor*

O/U is higher

O/U is lower

Cooling

Heating

2

Exterior dimensions

Net weight

Panel

Outdoor

Height x Width x Depth

Unit+Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDTC71VNXPVD

FDTC40VD

FDC71VNX

FDTC100VNXPVD

Twin

FDTC50VD

FDC100VNX

FDTC125VNXPVD

FDTC60VD

FDC125VNX

FDTC140VNXTVD

Triple

FDTC50VD

FDC140VNX

7.1

(3.2~8.0)

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

FDTC100VSXPVD

11.2

(4.0~16.0)

FDTC125VSXPVD FDTC140VSXTVD

FDTC50VD

FDC100VSX

Twin

FDTC60VD

FDC125VSX

Triple

FDTC50VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(4.0~18.0)

16.0

(4.0~20.0)

8.0

(3.6~9.0)

11.2

(4.0~12.5)

14.0

(4.0~17.0)

16.0

(4.0~18.0)

1.99/2.18

3.57/3.67

A/A

5(17)

Heating : Hi:42 Me:36 Lo:32

Cooling:51 Heating:48

2.78/3.02

3.60/3.71

A/A

5(24)

Cooling : Hi:42 Me:36 Lo:30

4.10/4.10

3.05/3.41

B/B

5(26)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

Cooling:48 Heating:50

4.34/4.34

3.23/3.69

A/A

2.78/3.02

3.60/3.71

A/A

4.10/4.10

3.05/3.41

B/B

Cooling : Hi:42 Me:36 Lo:30

5(15)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:42 Me:36 Lo:32

Cooling:49 Heating:52

Heating : Hi:46 Me:39 Lo:32

Cooling:48 Heating:50

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

Cooling:60 Heating:50

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

100

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

750x880(+88)x340

60

2.95(30)

Unit:248x570x570 Panel:35x700x700

18.5(Unit:15 Panel:3.5)

TC-PSA-25W-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-TC-24W-ER

1,300x970x370

105

4.5(30)

9.52/15.88

50 100

30

15

-15~43* 3

-20~20

4.34/4.34

3.23/3.69

A/A

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

Cooling:49 Heating:52

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 71/100/125VNXPVD 47dB, 100/125VSXPVD 47dB, 140VNXTVD 47dB, 140VSXTVD 47dB

Air flow: 71/100/125VNXPVD 13.5CMM, 100/125VSXPVD 13.5CMM, 140VNXTVD 13.5CMM, 140VSXTVD 13.5CMM

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Indoor*

O/U is higher

O/U is lower

Cooling

Heating

2

Outdoor

Exterior dimensions

Net weight

Panel

Air filter, Q'ty

Height x Width x Depth

Unit+Panel

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

Liquid/Gas kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDTC100VNPVD

FDTC50VD

FDC100VN

10.0

(4.0~11.2)

11.2

(4.0~12.5)

2.84/3.08

3.52/3.64

A/A

5(24)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

49

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

Micro Inverter

FDTC125VNPVD

Twin

FDTC60VD

FDC125VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(4.0~16.0)

5.35/4.62

2.34/3.03

F/D

5(27)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

Cooling:50 Heating:51

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

Cooling:75 Heating:73

Unit:248x570x570 Panel:35x700x700

18.5(Unit:15 Panel:3.5)

TC-PSA-25W-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-TC-24W-ER

845x970x370

81

3.8(30)

9.52/15.88

50

30

15

-15~43* 3

-20~20

Powerful-Hi can be selected. Sound level: 100/125VNPVD 47dB, 140VNTVD 47dB

Air flow: 100/125VNPVD 13.5CMM, 140VNTVD 13.5CMM

FDTC140VNTVD

Triple

FDTC50VD

FDC140VN

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.64/4.52

3.02/3.54

B/B

5(24)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

51

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Indoor* 2

Exterior dimensions

Net weight

Panel

Outdoor

Height x Width x Depth

Unit+Panel

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Ref.amount precharged

Height x Width x Depth

Liquid/Gas Ref.piping size

Range of usage

Ref.piping length

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDTC100VSPVD

FDTC50VD

FDC100VS

10.0

(4.0~11.2)

11.2

(4.0~12.5)

2.84/3.08

3.52/3.64

A/A

5(15)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

49

Cooling : Hi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

Twin

FDTC125VSPVD

FDTC60VD

FDC125VS

Triple

FDTC50VD

FDC140VS

FDTC50VD

FDC200VS

12.5

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

(5.0~14.0)

14.0

(5.0~14.5)

20.0

(7.0~22.4)

14.0

(4.0~16.0)

Micro Inverter

FDTC140VSTVD

16.0

(4.0~16.5)

FDTC200VSDVD

22.4

(7.6~25.0)

FDTC250VSDVD

Double Twin

FDTC60VD

FDC250VS

25.0

(10.0~28.0)

28.0

(9.5~31.5)

5.35/4.62

2.34/3.03

F/D

5(15)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

Cooling:50 Heating:51

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

Cooling:75 Heating:73

4.64/4.52

3.02/3.54

7.33/6.98

2.73/3.21

11.28/10.19

2.22/2.75

B/B

5(15)

D/C

5(19)

Cooling : Hi:42 Me:36 Lo:30

Heating : Hi:42 Me:36 Lo:32

51 57

F/E

5(22)

Cooling : Hi:46 Me:39 Lo:30

Heating : Hi:46 Me:39 Lo:32

Cooling:57 Heating:58

Cooling : PHi:11.5 Me:9 Lo:7

Heating : Hi:11.5 Me:9 Lo:8

Cooling : Hi:13.5 Me:10 Lo:7

Heating : Hi:13.5 Me:10 Lo:8

Cooling:150 Heating:145

3.8(30)

9.52/15.88

50

Unit:248x570x570 Panel:35x700x700

18.5(Unit:15 Panel:3.5)

TC-PSA-25W-E

Pocket Plastic net x1 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-TC-24W-ER

845x970x370

83

1,300x970x370

122

5.4(30)

9.52/22.22

30

15

-15~43* 3

-20~20

70

-15~20

1,505x970x370

140

7.2(30)

12.7/22.22

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100/125VSPVD 47dB, 140VSTVD 47dB, 200/250VSDVD 47dB

Air flow: 100/125VSPVD 13.5CMM, 140VSTVD 13.5CMM, 200/250VSDVD 13.5CMM

29

MULTI [ INDOOR UNIT ]

DUCT CONNECTED -Low/Middle Static pressure-

FDUM

SPECIFICATIONS external static pressure loss:5pa

Wired remote control

RC-E4

(Option)

RCH-E3

(Option)

FDUM 50/60/71/

100/125VD

Filter kit

UM-FL1E : for 50

UM-FL2E : for 60, 71

UM-FL3E : for 100, 125

(option)

Wireless remote control

RCN-KIT3-E

(Option)

A

CLASS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor* 2

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size Liquid/Gas

Ref.piping length

Range of usage

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDUM100VNXPVD FDUM125VNXPVD

Twin

FDUM50VD

FDC100VNX

FDUM60VD

FDC125VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

11.2

(4.0~12.5)

14.0

(4.0~17.0)

2.94/2.94

3.40/3.81

A/A

5(24)

3.86/4.10

3.24/3.41

A/B

5(26)

Hi:34 Me:31 Lo:28

Cooling:48 Heating:50

Hi:13 Me:12 Lo:11 Hi:16 Me:15 Lo:14

100

299x750x635

34

299x950x635

40

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43* 3

-20~20

SPECIFICATIONS The values are for simultaneous Multi operation.

30

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating kW kW kW

FDUM140VNXPVD

Twin

FDUM71VD

FDC140VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

14.0

(5.0~16.0)

14.0

(5.0~16.0)

16.0

(4.0~18.0)

FDUM140VNXTVD FDUM100VSXPVD

Triple

FDUM50VD

FDC140VNX

16.0

(4.0~18.0)

FDUM50VD

FDC100VSX

10.0

(4.0~11.2)

11.2

(4.0~16.0)

FDUM125VSXPVD FDUM140VSXPVD FDUM140VSXTVD

Twin

FDUM60VD

FDC125VSX

FDUM71VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(4.0~18.0)

16.0

(4.0~20.0)

Triple

FDUM50VD

FDC140VSX

14.0

(5.0~16.0)

16.0

(4.0~20.0)

4.60/4.69

4.60/4.69

2.94/2.94

3.86/4.10

4.60/4.69

4.60/4.69

COP Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Indoor* 2

Air flow

Exterior dimensions

Net weight

Air filter, Q'ty

Outdoor

Height x Width x Depth

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Ref.amount precharged

Ref.piping size Liquid/Gas

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

3.04/3.41

3.04/3.41

3.40/3.81

3.24/3.41

3.04/3.41

B/B B/B

5(26)

Hi:35 Me:32 Lo:29

Cooling:49 Heating:52 Cooling:49 Heating:52

Hi:20 Me:18 Lo:15

299x950x635

40

A/A

Hi:34 Me:31 Lo:28

A/B

Cooling:48 Heating:50

5(15)

B/B

Hi:35 Me:32 Lo:29

Cooling:49 Heating:52

Hi:13 Me:12 Lo:11 Hi:13 Me:12 Lo:11 Hi:16 Me:15 Lo:14

100

299x750x635

34

Procure locally

Hi:20 Me:18 Lo:15

299x950x635

40

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43* 3

-20~20

3.04/3.41

B/B

Hi:34 Me:31 Lo:28

Cooling:49 Heating:52

Hi:13 Me:12 Lo:11

299x750x635

34

*

*

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100VNXPVD 35dB, 100VSXPVD 35dB, 125/140VNXPVD 38dB, 125/140VSXPVD 38dB, 140VNXTVD 35dB, 140VSXTVD 35dB

Air flow: 100VNXPVD 14CMM, 100VSXPVD 14CMM, 125/140VNXPVD 18CMM, 125/140VSXPVD 18CMM, 140VNXTVD 14CMM, 140VSXTVD 14CMM

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating kW kW kW

FDUM100VNPVD

FDUM50VD

FDC100VN

10.0

(4.0~11.2)

11.2

(4.0~12.5)

3.12/3.27

3.21/3.43

FDUM125VNPVD

Twin

FDUM60VD

FDC125VN

12.5

(5.0~14.0)

14.0

(4.0~16.0)

Micro Inverter

FDUM140VNPVD

FDUM71VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDUM140VNTVD

Triple

FDUM50VD

FDC140VN

14.0

(5.0~14.5)

16.0

(4.0~16.5)

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Exterior dimensions

Net weight

Ref.amount precharged

Indoor* 2

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Height x Width x Depth

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

A/B

Hi:34 Me:31 Lo:28

49

Hi:13 Me:12 Lo:11

299x750x635

34

Powerful-Hi can be selected. Sound level: 100VNPVD 35dB, 125VNPVD 38dB, 140VNPVD 38dB, 140VNTVD 35dB, 100VSPVD 35dB

Air flow: 100VNPVD 14CMM, 125VNPVD 18CMM, 140VNPVD 23CMM, 140VNTVD 14CMM, 100VSPVD 14CMM

FDUM100VSPVD

Twin

FDUM50VD

FDC100VS

3Phase 380-415V 50Hz,

3Phase 380V 60Hz

10.0

(4.0~11.2)

14.0

(5.0~14.5)

16.0

(4.0~16.5)

11.2

(4.0~12.5)

4.47/4.51

2.80/3.10

50Hz:5.00/4.94

60Hz:5.00/4.80

50Hz:2.80/3.24

60Hz:2.80/3.33

C/D

Cooling:50 Heating:51

Hi:16 Me:15 Lo:14

C/C

Hi:34 Me:31 Lo:28

5(24)

Hi:35 Me:32 Lo:29

Hi:20 Me:18 Lo:15

Cooling:75 Heating:73

51

50Hz:5.09/5.03

60Hz:5.09/4.89

50Hz:2.75/3.18

60Hz:2.75/3.27

50Hz:D/D 60Hz:D/C

299x950x635

40

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

845x970x370

81

3.8(30)

9.52/15.88

50

30

15

-15~43* 3

-20~20

34

3.12/3.27

3.21/3.43

Hi:34 Me:31 Lo:28

Hi:13 Me:12 Lo:11

A/B

5(15)

49

299x750x635

83

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Indoor* 2

Air flow

Exterior dimensions

Net weight

Air filter, Q'ty

Exterior dimensions

Remote control(option)

Height x Width x Depth

Net weight

Ref.amount precharged

Outdoor

Height x Width x Depth

Liquid/Gas Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating mm kg kg(m)

ø m m m

O/U

O/U

The values are for simultaneous Multi operation.

kW kW kW

A dB(A)

CMM mm kg

Micro Inverter

FDUM125VSPVD FDUM140VSPVD FDUM200VSPVD

Twin

FDUM60VD

FDC125VS

12.5

(5.0~14.0)

FDUM71VD

FDC140VS

14.0

(5.0~14.5)

FDUM250VSPVD

FDUM100VD

FDC200VS

FDUM125VD

FDC250VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

20.0

(7.0~22.4)

25.0

(10.0~28.0)

FDUM140VSTVD

FDUM50VD

FDC140VS

14.0

(5.0~14.5)

FDUM200VSTVD

Triple

FDUM71VD

FDC200VS

20.0

(7.0~22.4)

22.4

(7.6~25.0)

14.0

(4.0~16.0)

16.0

(4.0~16.5)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

16.0

(4.0~16.5)

4.47/4.51

50Hz:5.00/4.94

60Hz:5.00/4.80

50Hz:2.80/3.24

2.80/3.10

C/D

5(15)

60Hz:2.80/3.33

C/C

Hi:34 Me:31 Lo:28

Cooling:50 Heating:51

Hi:35 Me:32 Lo:29

51

Hi:16 Me:15 Lo:14 Hi:20 Me:18 Lo:15

Cooling:75 Heating:73

299x950x635

40

845x970x370

83

3.8(30)

9.52/15.88

50

-20~20

6.86/6.72

2.92/3.33

9.31/8.35

2.69/3.35

C/C

5(19)

Hi:37 Me:35 Lo:32

57

D/C

5(22)

Hi:38 Me:36 Lo:33

Cooling:57 Heating:58

Hi:28 Me:25 Lo:22

Cooling:150 Heating:145

350x1,370x635

59

50Hz:5.09/5.03

60Hz:5.09/4.89

50Hz:2.75/3.18

60Hz:2.75/3.27

50Hz:D/D 60Hz:D/C

5(15)

Hi:34 Me:31 Lo:28

51

Hi:13 Me:12 Lo:11

Cooling:75 Heating:73

15

-15~43* 3

-15~20

299x750x635

34

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370 1,505x970x370

122

5.4(30)

9.52/22.22

70

30

140

7.2(30)

12.7/22.22

845x970x370

83

3.8(30)

9.52/15.88

50

-20~20

6.88/6.74

2.91/3.32

C/C

5(19)

Hi:35 Me:32 Lo:29

57

Hi:20 Me:18 Lo:15

Cooling:150 Heating:145

1,300x970x370

122

1,300x970x370

122

5.4(30)

9.52/22.22

70

-15~20

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of indoor units is 60Pa.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 125/140VSPVD 38dB, 200/250VSPVD 41dB, 140VSTVD 35dB, 200VSTVD 38dB

Air flow: 125VSPVD 18CMM, 140VSPVD 23CMM, 200/250VSPVD 34CMM, 140VSTVD 14CMM, 200VSTVD 23CMM

31

MULTI [ INDOOR UNIT ]

DUCT CONNECTED -Low/Middle Static pressure-

FDUM

SPECIFICATIONS external static pressure loss:5pa

Wired remote control

RC-E4

(Option)

RCH-E3

(Option)

FDUM 50/60/71/

100/125VD

Filter kit

UM-FL1E : for 50

UM-FL2E : for 60, 71

UM-FL3E : for 100, 125

(option)

Wireless remote control

RCN-KIT3-E

(Option)

A

CLASS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor* 2

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size Liquid/Gas

Ref.piping length

Range of usage

Vertical height difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDUM100VNXPVD FDUM125VNXPVD

Twin

FDUM50VD

FDC100VNX

FDUM60VD

FDC125VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

11.2

(4.0~12.5)

14.0

(4.0~17.0)

2.94/2.94

3.40/3.81

A/A

5(24)

3.86/4.10

3.24/3.41

A/B

5(26)

Hi:34 Me:31 Lo:28

Cooling:48 Heating:50

Hi:13 Me:12 Lo:11 Hi:16 Me:15 Lo:14

100

299x750x635

34

299x950x635

40

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43* 3

-20~20

SPECIFICATIONS The values are for simultaneous Multi operation.

30

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating kW kW kW

FDUM140VNXPVD

Twin

FDUM71VD

FDC140VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

14.0

(5.0~16.0)

14.0

(5.0~16.0)

16.0

(4.0~18.0)

FDUM140VNXTVD FDUM100VSXPVD

Triple

FDUM50VD

FDC140VNX

16.0

(4.0~18.0)

FDUM50VD

FDC100VSX

10.0

(4.0~11.2)

11.2

(4.0~16.0)

FDUM125VSXPVD FDUM140VSXPVD FDUM140VSXTVD

Twin

FDUM60VD

FDC125VSX

FDUM71VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(4.0~18.0)

16.0

(4.0~20.0)

Triple

FDUM50VD

FDC140VSX

14.0

(5.0~16.0)

16.0

(4.0~20.0)

4.60/4.69

4.60/4.69

2.94/2.94

3.86/4.10

4.60/4.69

4.60/4.69

COP Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Indoor* 2

Air flow

Exterior dimensions

Net weight

Air filter, Q'ty

Outdoor

Height x Width x Depth

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Ref.amount precharged

Ref.piping size Liquid/Gas

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

3.04/3.41

3.04/3.41

3.40/3.81

3.24/3.41

3.04/3.41

B/B B/B

5(26)

Hi:35 Me:32 Lo:29

Cooling:49 Heating:52 Cooling:49 Heating:52

Hi:20 Me:18 Lo:15

299x950x635

40

A/A

Hi:34 Me:31 Lo:28

A/B

Cooling:48 Heating:50

5(15)

B/B

Hi:35 Me:32 Lo:29

Cooling:49 Heating:52

Hi:13 Me:12 Lo:11 Hi:13 Me:12 Lo:11 Hi:16 Me:15 Lo:14

100

299x750x635

34

Procure locally

Hi:20 Me:18 Lo:15

299x950x635

40

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43* 3

-20~20

3.04/3.41

B/B

Hi:34 Me:31 Lo:28

Cooling:49 Heating:52

Hi:13 Me:12 Lo:11

299x750x635

34

*

*

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 100VNXPVD 35dB, 100VSXPVD 35dB, 125/140VNXPVD 38dB, 125/140VSXPVD 38dB, 140VNXTVD 35dB, 140VSXTVD 35dB

Air flow: 100VNXPVD 14CMM, 100VSXPVD 14CMM, 125/140VNXPVD 18CMM, 125/140VSXPVD 18CMM, 140VNXTVD 14CMM, 140VSXTVD 14CMM

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating kW kW kW

FDUM100VNPVD

FDUM50VD

FDC100VN

10.0

(4.0~11.2)

11.2

(4.0~12.5)

3.12/3.27

3.21/3.43

FDUM125VNPVD

Twin

FDUM60VD

FDC125VN

12.5

(5.0~14.0)

14.0

(4.0~16.0)

Micro Inverter

FDUM140VNPVD

FDUM71VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

FDUM140VNTVD

Triple

FDUM50VD

FDC140VN

14.0

(5.0~14.5)

16.0

(4.0~16.5)

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Exterior dimensions

Net weight

Ref.amount precharged

Indoor* 2

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Height x Width x Depth

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

A/B

Hi:34 Me:31 Lo:28

49

Hi:13 Me:12 Lo:11

299x750x635

34

Powerful-Hi can be selected. Sound level: 100VNPVD 35dB, 125VNPVD 38dB, 140VNPVD 38dB, 140VNTVD 35dB, 100VSPVD 35dB

Air flow: 100VNPVD 14CMM, 125VNPVD 18CMM, 140VNPVD 23CMM, 140VNTVD 14CMM, 100VSPVD 14CMM

FDUM100VSPVD

Twin

FDUM50VD

FDC100VS

3Phase 380-415V 50Hz,

3Phase 380V 60Hz

10.0

(4.0~11.2)

14.0

(5.0~14.5)

16.0

(4.0~16.5)

11.2

(4.0~12.5)

4.47/4.51

2.80/3.10

50Hz:5.00/4.94

60Hz:5.00/4.80

50Hz:2.80/3.24

60Hz:2.80/3.33

C/D

Hi:34 Me:31 Lo:28

Cooling:50 Heating:51

Hi:16 Me:15 Lo:14

C/C

5(24)

Hi:35 Me:32 Lo:29

Hi:20 Me:18 Lo:15

Cooling:75 Heating:73

51

50Hz:5.09/5.03

60Hz:5.09/4.89

50Hz:2.75/3.18

60Hz:2.75/3.27

50Hz:D/D 60Hz:D/C

299x950x635

40

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

845x970x370

81

3.8(30)

9.52/15.88

50

30

15

-15~43* 3

-20~20

34

3.12/3.27

3.21/3.43

Hi:34 Me:31 Lo:28

Hi:13 Me:12 Lo:11

A/B

5(15)

49

299x750x635

83

SPECIFICATIONS

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

ISO-T1(JIS)

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Indoor* 2

Air flow

Exterior dimensions

Net weight

Air filter, Q'ty

Exterior dimensions

Remote control(option)

Height x Width x Depth

Net weight

Ref.amount precharged

Outdoor

Height x Width x Depth

Liquid/Gas Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating mm kg kg(m)

ø m m m

O/U

O/U

The values are for simultaneous Multi operation.

kW kW kW

A dB(A)

CMM mm kg

Micro Inverter

FDUM125VSPVD FDUM140VSPVD FDUM200VSPVD

Twin

FDUM60VD

FDC125VS

12.5

(5.0~14.0)

FDUM71VD

FDC140VS

14.0

(5.0~14.5)

FDUM250VSPVD

FDUM100VD

FDC200VS

FDUM125VD

FDC250VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

20.0

(7.0~22.4)

25.0

(10.0~28.0)

FDUM140VSTVD

FDUM50VD

FDC140VS

14.0

(5.0~14.5)

FDUM200VSTVD

Triple

FDUM71VD

FDC200VS

20.0

(7.0~22.4)

22.4

(7.6~25.0)

14.0

(4.0~16.0)

16.0

(4.0~16.5)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

16.0

(4.0~16.5)

4.47/4.51

50Hz:5.00/4.94

60Hz:5.00/4.80

50Hz:2.80/3.24

2.80/3.10

C/D

5(15)

60Hz:2.80/3.33

C/C

Hi:34 Me:31 Lo:28

Cooling:50 Heating:51

Hi:35 Me:32 Lo:29

51

Hi:16 Me:15 Lo:14 Hi:20 Me:18 Lo:15

Cooling:75 Heating:73

299x950x635

40

845x970x370

83

3.8(30)

9.52/15.88

50

-20~20

6.86/6.72

2.92/3.33

9.31/8.35

2.69/3.35

C/C

5(19)

Hi:37 Me:35 Lo:32

57

D/C

5(22)

Hi:38 Me:36 Lo:33

Cooling:57 Heating:58

Hi:28 Me:25 Lo:22

Cooling:150 Heating:145

350x1,370x635

59

50Hz:5.09/5.03

60Hz:5.09/4.89

50Hz:2.75/3.18

60Hz:2.75/3.27

50Hz:D/D 60Hz:D/C

5(15)

Hi:34 Me:31 Lo:28

51

Hi:13 Me:12 Lo:11

Cooling:75 Heating:73

15

-15~43* 3

-15~20

299x750x635

34

Procure locally

Wired:RC-E4, RCH-E3 Wireless:RCN-KIT3-E

1,300x970x370 1,505x970x370

122

5.4(30)

9.52/22.22

70

30

140

7.2(30)

12.7/22.22

845x970x370

83

3.8(30)

9.52/15.88

50

-20~20

6.88/6.74

2.91/3.32

C/C

5(19)

Hi:35 Me:32 Lo:29

57

Hi:20 Me:18 Lo:15

Cooling:150 Heating:145

1,300x970x370

122

1,300x970x370

122

5.4(30)

9.52/22.22

70

-15~20

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB. External static pressure of indoor units is 60Pa.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 125/140VSPVD 38dB, 200/250VSPVD 41dB, 140VSTVD 35dB, 200VSTVD 38dB

Air flow: 125VSPVD 18CMM, 140VSPVD 23CMM, 200/250VSPVD 34CMM, 140VSTVD 14CMM, 200VSTVD 23CMM

31

32

MULTI [ INDOOR UNIT ]

CEILING SUSPENDED

FDEN

Wired remote control

RC-E4

(Option)

FDEN 40/50/60/71/100/125VD

RCH-E3

(Option)

Wireless remote control

RCN-E1R

(Option)

A

CLASS

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

Air flow

1

Indoor* 2

Outdoor

Indoor* 2

Outdoor

Height x Width x Depth Exterior dimensions

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

ISO-T1(JIS)

ISO-T1(JIS)

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN71VNXPVD FDEN100VNXPVD

Twin

FDEN40VD

FDC71VNX

FDEN50VD

FDC100VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

7.1

(3.2~8.0)

10.0

(4.0~11.2)

8.0

(3.6~9.0)

11.2

(4.0~12.5)

1.98/2.40

3.59/3.33

A/C

5(17)

3.02/3.18

3.31/3.52

A/B

5(24)

Hi:39 Me:38 Lo:37

Cooling:51 Heating:48 Cooling:48 Heating:50

Hi:11 Me:9 Lo:7

Cooling:60 Heating:50 100

210x1,070x690

28

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

750X880(+88)X340

60

2.95(30)

1,300x970x370

105

4.5(30)

9.52/15.88

50 100

30

15

-15~43* 3

-20~20

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor* 2

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN125VNXPVD FDEN140VNXPVD

FDEN60VD

FDC125VNX

Twin

FDEN71VD

FDC140VNX

FDEN140VNXTVD

Triple

FDEN50VD

FDC140VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(5.0~16.0)

14.0

(4.0~17.0)

16.0

(4.0~18.0)

16.0

(4.0~18.0)

FDEN100VSXPVD FDEN125VSXPVD FDEN140VSXPVD FDEN140VSXTVD

FDEN50VD

FDC100VSX

Twin

FDEN60VD

FDC125VSX

Triple

FDEN50VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(5.0~16.0)

11.2

(4.0~16.0)

14.0

(4.0~18.0)

FDEN71VD

FDC140VSX

16.0

(4.0~20.0)

16.0

(4.0~20.0)

3.86/3.70

3.24/3.78

A/A

4.78/4.43

2.93/3.61

C/A

Hi:41 Me:39 Lo:38

Cooling:48 Heating:50 Cooling:49 Heating:52

Hi:18 Me:14 Lo:12

5(26)

Hi:39 Me:38 Lo:37

Cooling:49 Heating:52

Hi:11 Me:9 Lo:7

49

100

210x1,320x690

37

4.72/4.38

2.97/3.65

C/A

3.02/3.18

3.31/3.52

A/B

3.86/3.70

3.24/3.78

A/A

4.78/4.43

2.93/3.61

C/A

5(15)

Hi:41 Me:39 Lo:38

Cooling:48 Heating:50 Cooling:49 Heating:52

Hi:18 Me:14 Lo:12

210x1,070x690

28

210x1,320x690

37

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43* 3

-20~20

4.72/4.38

2.97/3.65

C/A

Hi:39 Me:38 Lo:37

Cooling:49 Heating:52

Hi:11 Me:9 Lo:7

210x1,070x690

28

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 71/100VNXPVD 46dB, 100VSXPVD 46dB, 125/140VNXPVD 50dB, 125/140VSXPVD 50dB, 140VNXTVD 46dB, 140VSXTVD 46dB

Air flow: 71/100VNXPVD 13CMM, 100VSXPVD 13CMM, 125/140VNXPVD 22CMM, 125/140VSXPVD 22CMM, 140VNXTVD 13CMM, 140VSXTVD 13CMM

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Air flow

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Indoor* 2

Outdoor

Indoor*

Cooling

Heating

2

Exterior dimensions

Net weight

Exterior dimensions

Net weight

Ref.amount precharged

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Height x Width x Depth

Liquid/Gas

O/U is higher

O/U is lower kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN100VNPVD

FDEN50VD

FDC100VN

10.0

(4.0~11.2)

11.2

(4.0~12.5)

3.12/3.28

3.21/3.41

A/B

Hi:39 Me:38 Lo:37

49

Hi:11 Me:9 Lo:7

14.0

(4.0~16.0)

4.23/3.83

2.96/3.66

C/A

16.0

(4.0~16.5)

4.87/4.59

2.87/3.49

C/B

Hi:41 Me:39 Lo:38

Cooling:50 Heating:51

5(24)

Hi:18 Me:14 Lo:12

Micro Inverter

FDEN125VNPVD

Twin

FDEN60VD

FDC125VN

FDEN140VNPVD

FDEN71VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~14.5)

51

FDEN140VNTVD

Triple

FDEN50VD

FDC140VN

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.88/4.58

2.87/3.49

C/B

FDEN100VSPVD

Twin

FDEN125VSPVD

FDEN50VD

FDC100VS

FDEN60VD

FDC125VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

11.2

(4.0~12.5)

3.12/3.28

3.21/3.41

A/B

Hi:39 Me:38 Lo:37

Hi:11 Me:9 Lo:7

49

14.0

(4.0~16.0)

4.23/3.83

2.96/3.66

C/A

5(15)

Hi:41

Me:39 Lo:38

Cooling:50 Heating:51

Hi:18

Me:14 Lo:12

210x1,070x690

28

Cooling:75 Heating:73

210x1,320x690

37 28

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

845x970x370

210x1,070x690

81

3.8(30)

9.52/15.88

50

30

15

-15~43* 3

-20~20

Powerful-Hi can be selected. Sound level: 100VNPVD 46dB, 125/140VNPVD 50dB, 140VNTVD 46dB, 100VSPVD 46dB, 125VSPVD 50dB

Air flow: 100VNPVD 13CMM, 125/140VNPVD 22CMM, 140VNTVD 13CMM, 100VSPVD 13CMM, 125VSPVD 22CMM

83

210x1,320x690

37

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Indoor* 2

Exterior dimensions

Net weight

Air filter, Q'ty

Exterior dimensions

Remote control(option)

Height x Width x Depth

Net weight

Ref.amount precharged

Outdoor

Height x Width x Depth

Liquid/Gas Ref.piping size

Ref.piping length

Vertical height

difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN140VSPVD

FDEN71VD

FDC140VS

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.87/4.59

2.87/3.49

C/B

5(15)

Hi:41

Me:39 Lo:38

51

Hi:18

Me:14 Lo:12

Cooling:75 Heating:73

210x1,320x690

37

845x970x370

83

3.8(30)

9.52/15.88

50

-20~20

FDEN200VSPVD

Twin

FDEN100VD

FDC200VS

Micro Inverter

FDEN250VSPVD

FDEN125VD

FDC250VS

FDEN140VSTVD

FDEN50VD

FDC140VS

FDEN200VSTVD FDEN200VSDVD FDEN250VSDVD

Triple

FDEN71VD

FDC200VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

25.0

(10.0~28.0)

14.0

(5.0~14.5)

20.0

(7.0~22.4)

FDEN50VD

FDC200VS

20.0

Double Twin

(7.0~22.4)

FDEN60VD

FDC250VS

25.0

(10.0~28.0)

20.0

(7.0~22.4)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

16.0

(4.0~16.5)

22.4

(7.6~25.0)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

6.47/5.97

3.09/3.75

B/A

5(19)

Hi:44

9.01/8.05

2.77/3.48

D/B

5(22)

Hi:46

Me:41 Lo:39

57

Hi:26

Me:23 Lo:21

Me:44 Lo:43

Cooling:57 Heating:58

Cooling:150 Heating:145

250x1,620x690

49

Hi:29

Me:26 Lo:23

4.88/4.58

2.87/3.49

C/B

5(15)

Hi:39

Me:38 Lo:37

51

Hi:11

Me:9 Lo:7

Cooling:75 Heating:73

6.40/5.90

3.13/3.80

B/A

Hi:41

Me:39 Lo:38

Hi:18

5(19)

57

7.43/7.26

2.69/3.09

D/D

Hi:39

Me:38 Lo:37

Hi:11

Me:39 Lo:38

Cooling:57 Heating:58

Me:14 Lo:12 Me:9 Lo:7

Cooling:150 Heating:145

-15~20

210x1,070x690

28

15

-15~43* 3

-20~20

210x1,320x690

37

210x1,070x690

28

1,300x970x370

122

5.4(30)

9.52/22.22

70

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

1,505x970x370

140

7.2(30)

12.7/22.22

845x970x370

83

3.8(30)

9.52/15.88

1,300x970x370

122

5.4(30)

9.52/22.22

50

30

70

-15~20

9.50/8.69

2.63/3.22

D/C

5(22)

Hi:41

Hi:18

Me:14 Lo:12

210x1,320x690

37

1,505x970x370

140

7.2(30)

12.7/22.2

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 140VSPVD 50dB, 200VSPVD 46dB, 250VSPVD 50dB, 140VSTVD 46dB, 200VSTVD 50dB, 200VSDVD 46dB, 250VSDVD 50dB

Air flow: 140VSPVD 22CMM, 200VSPVD 28CMM, 250VSPVD 32CMM, 140VSTVD 13CMM, 200VSTVD 22CMM, 200VSDVD 13CMM, 250VSDVD 22CMM

33

32

MULTI [ INDOOR UNIT ]

CEILING SUSPENDED

FDEN

Wired remote control

RC-E4

(Option)

FDEN 40/50/60/71/100/125VD

RCH-E3

(Option)

Wireless remote control

RCN-E1R

(Option)

A

CLASS

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

Air flow

1

Indoor* 2

Outdoor

Indoor* 2

Outdoor

Height x Width x Depth Exterior dimensions

Net weight

Air filter, Q'ty

Remote control(option)

Exterior dimensions

Net weight

Height x Width x Depth

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

ISO-T1(JIS)

ISO-T1(JIS)

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN71VNXPVD FDEN100VNXPVD

Twin

FDEN40VD

FDC71VNX

FDEN50VD

FDC100VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

7.1

(3.2~8.0)

10.0

(4.0~11.2)

8.0

(3.6~9.0)

11.2

(4.0~12.5)

1.98/2.40

3.59/3.33

A/C

5(17)

3.02/3.18

3.31/3.52

A/B

5(24)

Hi:39 Me:38 Lo:37

Cooling:51 Heating:48 Cooling:48 Heating:50

Hi:11 Me:9 Lo:7

Cooling:60 Heating:50 100

210x1,070x690

28

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

750X880(+88)X340

60

2.95(30)

1,300x970x370

105

4.5(30)

9.52/15.88

50 100

30

15

-15~43* 3

-20~20

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel* 1

Indoor* 2

Outdoor

Air flow

Exterior dimensions

Net weight

Indoor* 2

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Liquid/Gas

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN125VNXPVD FDEN140VNXPVD

FDEN60VD

FDC125VNX

Twin

FDEN71VD

FDC140VNX

FDEN140VNXTVD

Triple

FDEN50VD

FDC140VNX

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(5.0~16.0)

14.0

(4.0~17.0)

16.0

(4.0~18.0)

16.0

(4.0~18.0)

FDEN100VSXPVD FDEN125VSXPVD FDEN140VSXPVD FDEN140VSXTVD

FDEN50VD

FDC100VSX

Twin

FDEN60VD

FDC125VSX

Triple

FDEN50VD

FDC140VSX

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

14.0

(5.0~16.0)

11.2

(4.0~16.0)

14.0

(4.0~18.0)

FDEN71VD

FDC140VSX

16.0

(4.0~20.0)

16.0

(4.0~20.0)

3.86/3.70

3.24/3.78

A/A

4.78/4.43

2.93/3.61

C/A

Hi:41 Me:39 Lo:38

Cooling:48 Heating:50 Cooling:49 Heating:52

Hi:18 Me:14 Lo:12

5(26)

Hi:39 Me:38 Lo:37

Cooling:49 Heating:52

Hi:11 Me:9 Lo:7

49

100

210x1,320x690

37

4.72/4.38

2.97/3.65

C/A

3.02/3.18

3.31/3.52

A/B

3.86/3.70

3.24/3.78

A/A

4.78/4.43

2.93/3.61

C/A

5(15)

Hi:41 Me:39 Lo:38

Cooling:48 Heating:50 Cooling:49 Heating:52

Hi:18 Me:14 Lo:12

210x1,070x690

28

210x1,320x690

37

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43* 3

-20~20

4.72/4.38

2.97/3.65

C/A

Hi:39 Me:38 Lo:37

Cooling:49 Heating:52

Hi:11 Me:9 Lo:7

210x1,070x690

28

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 71/100VNXPVD 46dB, 100VSXPVD 46dB, 125/140VNXPVD 50dB, 125/140VSXPVD 50dB, 140VNXTVD 46dB, 140VSXTVD 46dB

Air flow: 71/100VNXPVD 13CMM, 100VSXPVD 13CMM, 125/140VNXPVD 22CMM, 125/140VSXPVD 22CMM, 140VNXTVD 13CMM, 140VSXTVD 13CMM

SPECIFICATIONS

The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Cooling/Heating

Cooling/Heating

Energy label Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Air flow

Ref.piping size

Ref.piping length

Vertical height

Range of usage difference

Operating temperature range

Indoor* 2

Outdoor

Indoor*

Cooling

Heating

2

Exterior dimensions

Net weight

Exterior dimensions

Net weight

Ref.amount precharged

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Height x Width x Depth

Liquid/Gas

O/U is higher

O/U is lower kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN100VNPVD

FDEN50VD

FDC100VN

10.0

(4.0~11.2)

11.2

(4.0~12.5)

3.12/3.28

3.21/3.41

A/B

Hi:39 Me:38 Lo:37

49

Hi:11 Me:9 Lo:7

14.0

(4.0~16.0)

4.23/3.83

2.96/3.66

C/A

16.0

(4.0~16.5)

4.87/4.59

2.87/3.49

C/B

Hi:41 Me:39 Lo:38

Cooling:50 Heating:51

5(24)

Hi:18 Me:14 Lo:12

Micro Inverter

FDEN125VNPVD

Twin

FDEN60VD

FDC125VN

FDEN140VNPVD

FDEN71VD

FDC140VN

1Phase 220-240V 50Hz, 1Phase 220V 60Hz

12.5

(5.0~14.0)

14.0

(5.0~14.5)

51

FDEN140VNTVD

Triple

FDEN50VD

FDC140VN

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.88/4.58

2.87/3.49

C/B

FDEN100VSPVD

Twin

FDEN125VSPVD

FDEN50VD

FDC100VS

FDEN60VD

FDC125VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

11.2

(4.0~12.5)

3.12/3.28

3.21/3.41

A/B

Hi:39 Me:38 Lo:37

Hi:11 Me:9 Lo:7

49

14.0

(4.0~16.0)

4.23/3.83

2.96/3.66

C/A

5(15)

Hi:41

Me:39 Lo:38

Cooling:50 Heating:51

Hi:18

Me:14 Lo:12

210x1,070x690

28

Cooling:75 Heating:73

210x1,320x690

37 28

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

845x970x370

210x1,070x690

81

3.8(30)

9.52/15.88

50

30

15

-15~43* 3

-20~20

Powerful-Hi can be selected. Sound level: 100VNPVD 46dB, 125/140VNPVD 50dB, 140VNTVD 46dB, 100VSPVD 46dB, 125VSPVD 50dB

Air flow: 100VNPVD 13CMM, 125/140VNPVD 22CMM, 140VNTVD 13CMM, 100VSPVD 13CMM, 125VSPVD 22CMM

83

210x1,320x690

37

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

ISO-T1(JIS)

(Min~Max)

Power Consumption

COP

Energy label

ISO-T1(JIS)

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel*

1

Indoor* 2

Outdoor

Air flow

Indoor* 2

Exterior dimensions

Net weight

Air filter, Q'ty

Exterior dimensions

Remote control(option)

Height x Width x Depth

Net weight

Ref.amount precharged

Outdoor

Height x Width x Depth

Liquid/Gas Ref.piping size

Ref.piping length

Vertical height

difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

FDEN140VSPVD

FDEN71VD

FDC140VS

14.0

(5.0~14.5)

16.0

(4.0~16.5)

4.87/4.59

2.87/3.49

C/B

5(15)

Hi:41

Me:39 Lo:38

51

Hi:18

Me:14 Lo:12

Cooling:75 Heating:73

210x1,320x690

37

845x970x370

83

3.8(30)

9.52/15.88

50

-20~20

FDEN200VSPVD

Twin

FDEN100VD

FDC200VS

Micro Inverter

FDEN250VSPVD

FDEN125VD

FDC250VS

FDEN140VSTVD

FDEN50VD

FDC140VS

FDEN200VSTVD FDEN200VSDVD FDEN250VSDVD

Triple

FDEN71VD

FDC200VS

3Phase 380-415V 50Hz, 3Phase 380V 60Hz

25.0

(10.0~28.0)

14.0

(5.0~14.5)

20.0

(7.0~22.4)

FDEN50VD

FDC200VS

20.0

Double Twin

(7.0~22.4)

FDEN60VD

FDC250VS

25.0

(10.0~28.0)

20.0

(7.0~22.4)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

16.0

(4.0~16.5)

22.4

(7.6~25.0)

22.4

(7.6~25.0)

28.0

(9.5~31.5)

6.47/5.97

3.09/3.75

B/A

5(19)

Hi:44

9.01/8.05

2.77/3.48

D/B

5(22)

Hi:46

Me:41 Lo:39

57

Hi:26

Me:23 Lo:21

Me:44 Lo:43

Cooling:57 Heating:58

Cooling:150 Heating:145

250x1,620x690

49

Hi:29

Me:26 Lo:23

4.88/4.58

2.87/3.49

C/B

5(15)

Hi:39

Me:38 Lo:37

51

Hi:11

Me:9 Lo:7

Cooling:75 Heating:73

6.40/5.90

3.13/3.80

B/A

Hi:41

Me:39 Lo:38

Hi:18

5(19)

57

7.43/7.26

2.69/3.09

D/D

Hi:39

Me:38 Lo:37

Hi:11

Me:39 Lo:38

Cooling:57 Heating:58

Me:14 Lo:12 Me:9 Lo:7

Cooling:150 Heating:145

-15~20

210x1,070x690

28

15

-15~43* 3

-20~20

210x1,320x690

37

210x1,070x690

28

1,300x970x370

122

5.4(30)

9.52/22.22

70

Pocket Plastic net x2 (Washable)

Wired:RC-E4, RCH-E3 Wireless:RCN-E1R

1,505x970x370

140

7.2(30)

12.7/22.22

845x970x370

83

3.8(30)

9.52/15.88

1,300x970x370

122

5.4(30)

9.52/22.22

50

30

70

-15~20

9.50/8.69

2.63/3.22

D/C

5(22)

Hi:41

Hi:18

Me:14 Lo:12

210x1,320x690

37

1,505x970x370

140

7.2(30)

12.7/22.2

The data are measured under the following conditions(ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB. Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

* 2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

Powerful-Hi can be selected. Sound level: 140VSPVD 50dB, 200VSPVD 46dB, 250VSPVD 50dB, 140VSTVD 46dB, 200VSTVD 50dB, 200VSDVD 46dB, 250VSDVD 50dB

Air flow: 140VSPVD 22CMM, 200VSPVD 28CMM, 250VSPVD 32CMM, 140VSTVD 13CMM, 200VSTVD 22CMM, 200VSDVD 13CMM, 250VSDVD 22CMM

33

MULTI [ INDOOR UNIT ]

WALL MOUNTED

SRK

Only used with outdoor units of TWIN, TRIPLE, MULTI System.

A

CLASS

SRK 50/60ZJX-S

Wired remote control

RC-E4

(Option)

RCH-E3

(Option)

34

Point

1

Jet Air Scroll

We used the same aerodynamic analysis technology as used in developing jet engines.

CFD (computational fluid dynamics), used in blade shape design of jet engines, has been applied to the design of air channels in air conditioners to develop the ideal air channel system (air circulation). The airflow of the jets created in this system enable a large volume of air to be blown with minimum power consumption, yet the air flow is uniform, quiet and reaches points a long distance from the blower.

Fast Slow

Colors in the figure show the air speed.

Point

2

Long Reach Air Flow

Powerful airflow is realized by Jet technology.

Good for large living rooms and shops.

Increase your comfort.

SRK50/60ZJX-S

(in cooling operation)

SC-BIKN-E

RC-E4

Outline drawing (Unit:mm)

881.9

26 60 60 21

890

SC-BIKN-E

220 3

Piping hole right

Terminal block

122.1

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Energy label

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel * 1

Cooling/Heating

Indoor * 2

Cooling

Heating

Air flow

Exterior dimensions

Net weight

Outdoor

Indoor * 2

Cooling

Heating

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Vertical height

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

SRK100VNXPZJX SRK125VNXPZJX SRK140VNXTZJX

Twin Triple

SRK50ZJX-S

FDC100VNX

SRK60ZJX-S

FDC125VNX

SRK50ZJX-S

FDC140VNX

1Phase 220-240 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

11.2

(4.0~12.5)

14.0

(4.0~17.0)

16.0

(4.0~18.0)

SRK100VSXPZJX SRK125VSXPZJX

Twin

SRK140VSXTZJX

Triple

SRK50ZJX-S

FDC100VSX

SRK60ZJX-S

FDC125VSX

SRK50ZJX-S

FDC140VSX

3Phase 380-415 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

11.2

(4.0~16.0)

14.0

(4.0~18.0)

16.0

(4.0~20.0)

3.98/3.68

3.52/4.35

A/A

2.66/2.60

3.76/4.31

A/A

3.60/3.48

3.47/4.02

A/A

5 (24)

Hi:45 Me:38 Lo:26 Hi:47 Me:38 Lo:26

Hi:45 Me:38 Lo:32 Hi:45 Me:39 Lo:33

Cooling:48 Heating:50

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

Hi:14.5 Me:12.5 Lo:8.5

Hi:17 Me:15 Lo:11

3.98/3.68

3.52/4.35

A/A

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

Cooling:49 Heating:52

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

2.66/2.60

3.76/4.31

A/A

3.60/3.48

3.47/4.02

A/A

5 (15)

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

Hi:47 Me:38 Lo:26

Hi:45 Me:39 Lo:33

Cooling:48 Heating:50

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

100

309x890x220

15

Hi:14.5 Me:12.5 Lo:8.5

Hi:17 Me:15 Lo:11

Polypropylene net x2 (Washable)

Wired:RC-E4, RCH-E3 & Interface kit:SC-BIKN-E

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43 * 3

-20~20

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

Cooling:49 Heating:52

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Energy label

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel * 1

Indoor * 2

Cooling

Heating

Outdoor

Air flow

Indoor * 2

Cooling

Heating

Range of usage

Exterior dimensions

Net weight

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Liquid/Gas difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

SRK100VNPZJX

11.2

(4.0~12.5)

SRK125VNPZJX

14.0

(4.0~16.0)

SRK140VNTZJX

Twin Triple

SRK50ZJX-S

FDC100VN

SRK60ZJX-S

FDC125VN

SRK50ZJX-S

FDC140VN

1Phase 220-240 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

16.0

(4.0~16.5)

Micro Inverter

SRK100VSPZJX

11.2

(4.0~12.5)

SRK125VSPZJX

Twin Triple

SRK50ZJX-S

FDC100VS

SRK60ZJX-S

FDC125VS

SRK50ZJX-S

FDC140VS

3Phase 380-415 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

14.0

(4.0~16.0)

SRK140VSTZJX

16.0

(4.0~16.5)

2.72/2.86

3.62/3.92

A/A

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

49

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

4.25/4.29

2.94/3.26

C/C

5 (24)

Hi:47 Me:38 Lo:26

Hi:45 Me:39 Lo:33

Cooling:50,Heating:51

Hi:14.5 Me:12.5 Lo:8.5

Hi:17 Me:15 Lo:11

4.53/4.05

3.09/3.95

B/A

2.72/2.86

3.62/3.92

A/A

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

51

Hi:13.5 Me:11 Lo:8

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

49

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

Hi:16.5 Me:14.5 Lo:10.5

Cooling:75,Heating:73

309x890x220

15

Polypropylene net x2 (Washable)

Wired:RC-E4, RCH-E3 & Interface kit:SC-BIKN-E

845x970x370

4.25/4.29

2.94/3.26

C/C

5 (15)

Hi:47 Me:38 Lo:26

Hi:45 Me:39 Lo:33

Cooling:50,Heating:51

Hi:14.5 Me:12.5 Lo:8.5

Hi:17 Me:15 Lo:11

81 83

3.8(30)

9.52/15.88

50

30

15

-15~43 * 3

-20~20

4.53/4.05

3.09/3.95

B/A

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

51

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

The data are measured under the following conditions (ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB.

Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

35

MULTI [ INDOOR UNIT ]

WALL MOUNTED

SRK

Only used with outdoor units of TWIN, TRIPLE, MULTI System.

A

CLASS

SRK 50/60ZJX-S

Wired remote control

RC-E4

(Option)

RCH-E3

(Option)

34

Point

1

Jet Air Scroll

We used the same aerodynamic analysis technology as used in developing jet engines.

CFD (computational fluid dynamics), used in blade shape design of jet engines, has been applied to the design of air channels in air conditioners to develop the ideal air channel system (air circulation). The airflow of the jets created in this system enable a large volume of air to be blown with minimum power consumption, yet the air flow is uniform, quiet and reaches points a long distance from the blower.

Fast Slow

Colors in the figure show the air speed.

Point

2

Long Reach Air Flow

Powerful airflow is realized by Jet technology.

Good for large living rooms and shops.

Increase your comfort.

SRK50/60ZJX-S

(in cooling operation)

SC-BIKN-E

RC-E4

Outline drawing (Unit:mm)

881.9

26 60 60 21

890

SC-BIKN-E

220 3

Piping hole right

Terminal block

122.1

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Energy label

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel * 1

Cooling/Heating

Indoor * 2

Cooling

Heating

Air flow

Exterior dimensions

Net weight

Outdoor

Indoor * 2

Cooling

Heating

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Ref.amount precharged

Ref.piping size

Ref.piping length

Liquid/Gas

Vertical height

Range of usage difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

SRK100VNXPZJX SRK125VNXPZJX SRK140VNXTZJX

Twin Triple

SRK50ZJX-S

FDC100VNX

SRK60ZJX-S

FDC125VNX

SRK50ZJX-S

FDC140VNX

1Phase 220-240 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

11.2

(4.0~12.5)

14.0

(4.0~17.0)

16.0

(4.0~18.0)

SRK100VSXPZJX SRK125VSXPZJX

Twin

SRK140VSXTZJX

Triple

SRK50ZJX-S

FDC100VSX

SRK60ZJX-S

FDC125VSX

SRK50ZJX-S

FDC140VSX

3Phase 380-415 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~16.0)

11.2

(4.0~16.0)

14.0

(4.0~18.0)

16.0

(4.0~20.0)

3.98/3.68

3.52/4.35

A/A

2.66/2.60

3.76/4.31

A/A

3.60/3.48

3.47/4.02

A/A

5 (24)

Hi:45 Me:38 Lo:26 Hi:47 Me:38 Lo:26

Hi:45 Me:38 Lo:32 Hi:45 Me:39 Lo:33

Cooling:48 Heating:50

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

Hi:14.5 Me:12.5 Lo:8.5

Hi:17 Me:15 Lo:11

3.98/3.68

3.52/4.35

A/A

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

Cooling:49 Heating:52

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

2.66/2.60

3.76/4.31

A/A

3.60/3.48

3.47/4.02

A/A

5 (15)

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

Hi:47 Me:38 Lo:26

Hi:45 Me:39 Lo:33

Cooling:48 Heating:50

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

100

309x890x220

15

Hi:14.5 Me:12.5 Lo:8.5

Hi:17 Me:15 Lo:11

Polypropylene net x2 (Washable)

Wired:RC-E4, RCH-E3 & Interface kit:SC-BIKN-E

1,300x970x370

105

4.5(30)

9.52/15.88

100

30

15

-15~43

-20~20

* 3

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

Cooling:49 Heating:52

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

SPECIFICATIONS The values are for simultaneous Multi operation.

Set model name

Indoor name

Outdoor name

Power source

Nominal cooling capacity

(Min~Max)

Nominal heating capacity

(Min~Max)

ISO-T1(JIS)

ISO-T1(JIS)

Power Consumption

COP

Energy label

Cooling/Heating

Cooling/Heating

Cooling/Heating

Inrush current (Max. running current)

Sound Ievel * 1

Indoor * 2

Cooling

Heating

Outdoor

Air flow

Indoor * 2

Cooling

Heating

Range of usage

Exterior dimensions

Net weight

Outdoor

Height x Width x Depth

Air filter, Q'ty

Remote control(option)

Exterior dimensions Height x Width x Depth

Net weight

Ref.amount precharged

Ref.piping size

Ref.piping length

Vertical height

Liquid/Gas difference

Operating temperature range

O/U is higher

O/U is lower

Cooling

Heating kW kW kW

A dB(A)

CMM mm kg mm kg kg(m)

ø m m m

O/U

O/U

SRK100VNPZJX

11.2

(4.0~12.5)

SRK125VNPZJX

14.0

(4.0~16.0)

SRK140VNTZJX

Twin Triple

SRK50ZJX-S

FDC100VN

SRK60ZJX-S

FDC125VN

SRK50ZJX-S

FDC140VN

1Phase 220-240 50Hz, 1Phase 220V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

16.0

(4.0~16.5)

Micro Inverter

SRK100VSPZJX

11.2

(4.0~12.5)

SRK125VSPZJX

Twin Triple

SRK50ZJX-S

FDC100VS

SRK60ZJX-S

FDC125VS

SRK50ZJX-S

FDC140VS

3Phase 380-415 50Hz, 3Phase 380V 60Hz

10.0

(4.0~11.2)

12.5

(5.0~14.0)

14.0

(5.0~14.5)

14.0

(4.0~16.0)

SRK140VSTZJX

16.0

(4.0~16.5)

2.72/2.86

3.62/3.92

A/A

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

49

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

4.25/4.29

2.94/3.26

C/C

5 (24)

Hi:47 Me:38 Lo:26

Hi:45 Me:39 Lo:33

Cooling:50,Heating:51

Hi:14.5 Me:12.5 Lo:8.5

Hi:17 Me:15 Lo:11

4.53/4.05

3.09/3.95

B/A

2.72/2.86

3.62/3.92

A/A

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

51

Hi:13.5 Me:11 Lo:8

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

49

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

Hi:16.5 Me:14.5 Lo:10.5

Cooling:75,Heating:73

309x890x220

15

Polypropylene net x2 (Washable)

Wired:RC-E4, RCH-E3 & Interface kit:SC-BIKN-E

845x970x370

4.25/4.29

2.94/3.26

C/C

5 (15)

Hi:47 Me:38 Lo:26

Hi:45 Me:39 Lo:33

Cooling:50,Heating:51

Hi:14.5 Me:12.5 Lo:8.5

Hi:17 Me:15 Lo:11

81 83

3.8(30)

9.52/15.88

50

30

15

-15~43 * 3

-20~20

4.53/4.05

3.09/3.95

B/A

Hi:45 Me:38 Lo:26

Hi:45 Me:38 Lo:32

51

Hi:13.5 Me:11 Lo:8

Hi:16.5 Me:14.5 Lo:10.5

The data are measured under the following conditions (ISO-T1).

Cooling:Indoor temp. of 27˚CDB, 19˚CWB, and outdoor temp. of 35˚CDB.

Heating:Indoor temp. of 20˚CDB, and outdoor temp. of 7˚CDB, 6˚CWB.

* 1 : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.

2 : The values are for one indoor unit operation.

* 3 : If a cooling operation is conducted when the outdoor air temperature is –5˚C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.

35

OUTDOOR UNIT (1.5-10.0HP)

SRC40ZIX-S

SRC50ZIX-S

SRC60ZIX-S

*

(1.5HP~2.5HP)

* SRC50/60ZIX-S is common for both of outdoor units of

SRK50/60ZJX-S (Residential Air-conditioners) and 1.5,

2, 2.5HP of Inverter Packaged Air-Conditioners.

Common components make for easy inventory control and the installation procedure will be the same.

NEW

FDC71VNX

(3.0HP)

FDC100VNX

FDC100VSX

(4.0HP)

FDC125VNX

FDC125VSX

(5.0HP)

FDC140VNX

FDC140VSX

(6.0HP)

Blue Fin (3~10HP)

Due to application of blue coated fins (KS101) for the heat exchanger of new outdoor unit, corrosion resistance has been improved compared to current models.

FDC100VN

FDC125VN

FDC100VS

FDC125VS

FDC140VN FDC140VS

(4.0HP~6.0HP)

FDC200VS

(8.0HP)

FDC250VS

(10.0HP)

Base heater kit (option)

This kit is recommended to be used in an area where the lowest temperature drops below 0˚C.

CW-H-E applied for

FDC100~250VN,VS

FDC100~140VNX,VSX

Installation workability

Enhanced installation workability thanks to the extended pipe length – longest level in the industry and pre-charged refrigerant.

Point

1

Piping length – 100m (Hyper Inverter 4~6HP)

Refer to our Technical Manual in detail

Micro Inverter

Height difference

(Outdoor higher than Indoor)

Height difference

(Outdoor higher than Indoor)

Piping length

Piping length

HP

1.5~2.5

Piping length

30m

3

4~6

50m

100m

Height difference

20m

30m

30m

HP

4~6

8.10

Piping length

50m

70m

Height difference

30m

30m

36

Point

2

Refrigerant precharged piping length extending to 30m

Refrigerant precharged piping length extends up to 30m. (1.5~2.5HP:15m)

This eliminates the need to add refrigerant on site, which sets it free from trouble of excessive or insufficient charging of refrigerant, and allows carrying out the installation smoothly.

Control Systems [Individual control]

Remote Control line up indoor unit wired all models remote control

RC-E4

RCH-E3 wireless indoor unit

FDT

FDTC

FDUM, FDU

FDEN remote control

RCN-T-36W-E

RCN-TC-24W-ER

RCN-KIT3-E

RCN-E1R

Wired remote control with weekly timer (option)

RC-E4

Run hour meters to facilitate maintenance checking

RC-E4 stores operation data when an anomaly occurs and indicates the error on the LCD. It also displays cumulative operation hours of the air conditioner and compressor since commissioning.

The RC-E4 controller enables extensive access to service and maintenance technical data combined with easy to use functions and a clear LCD display.

Room temperature controlled

by the remote control sensor

The temperature sensor is housed in the top section of the remote control unit. This arrangement has improved the sensitivity of the remote control unit’s sensor, which permits more finely controlled air conditioning.

Weekly timer function as standard

RC-E4 provides (as a standard feature) a weekly timer, which allows oneweek operation schedules to be registered. A user can specify up to four times a day to start/stop the air conditioner. (Temperature setting is also possible with the timer).

Timer operation

Changeable set temperature ranges

RC-E4 allows the upper and lower limits of a set temperature range to be specified separately.

By adjusting a set temperature range, you can ensure energy saving air conditioning by avoiding excessive cooling or heating.

Upper limit

Lower limit

Changeable range

20~30 °C(effective for heating operation)

18~26 °C(effective for non-heating operation)

Simple remote control (option)

RCH-E3 (wired)

Considering specialized usage in hotel rooms, control buttons are limited only to minimum required functions such as ON/OFF, mode, temperature setting and fan speed. It is really simple and easy to use.

RCH-E3 is not applicable to the Individual flap control system and the Flap control system.

When RCH-E3 is used, the fan has 3 speed settings (Hi-

Me-Lo) only.

Up to 16 units

It can control up to 16 units individually, with pressing the AIR CON No. button.

AUTO restart

This function allows starting the air conditioner automatically when power supply is restored after power failure or by turning on the power switch.

Wireless remote control (option)

For wireless control simply insert the infrared receiver kit on a corner of the panel.

RCN-T-36W-E,

RCN-TC-24W-ER

RCN-KIT3-E RCN-E1R

Thermistor (option)

SC-THB-E3

In case sensor in the indoor units or the remote control sensor can not sense the room temperature correctly, or individual remote control in each room is not required but only censor is required (as when center control system is in place), install SC-THB-E3 at proper place in the rooms.

When wireless remote control is used, the fan has 3 speed settings (Hi-Me-Lo) only.

37

OUTDOOR UNIT (1.5-10.0HP)

SRC40ZIX-S

SRC50ZIX-S

SRC60ZIX-S

*

(1.5HP~2.5HP)

* SRC50/60ZIX-S is common for both of outdoor units of

SRK50/60ZJX-S (Residential Air-conditioners) and 1.5,

2, 2.5HP of Inverter Packaged Air-Conditioners.

Common components make for easy inventory control and the installation procedure will be the same.

NEW

FDC71VNX

(3.0HP)

FDC100VNX

FDC100VSX

(4.0HP)

FDC125VNX

FDC125VSX

(5.0HP)

FDC140VNX

FDC140VSX

(6.0HP)

Blue Fin (3~10HP)

Due to application of blue coated fins (KS101) for the heat exchanger of new outdoor unit, corrosion resistance has been improved compared to current models.

FDC100VN

FDC125VN

FDC100VS

FDC125VS

FDC140VN FDC140VS

(4.0HP~6.0HP)

FDC200VS

(8.0HP)

FDC250VS

(10.0HP)

Base heater kit (option)

This kit is recommended to be used in an area where the lowest temperature drops below 0˚C.

CW-H-E applied for

FDC100~250VN,VS

FDC100~140VNX,VSX

Installation workability

Enhanced installation workability thanks to the extended pipe length – longest level in the industry and pre-charged refrigerant.

Point

1

Piping length – 100m (Hyper Inverter 4~6HP)

Refer to our Technical Manual in detail

Micro Inverter

Height difference

(Outdoor higher than Indoor)

Height difference

(Outdoor higher than Indoor)

Piping length

Piping length

HP

1.5~2.5

Piping length

30m

3

4~6

50m

100m

Height difference

20m

30m

30m

HP

4~6

8.10

Piping length

50m

70m

Height difference

30m

30m

36

Point

2

Refrigerant precharged piping length extending to 30m

Refrigerant precharged piping length extends up to 30m. (1.5~2.5HP:15m)

This eliminates the need to add refrigerant on site, which sets it free from trouble of excessive or insufficient charging of refrigerant, and allows carrying out the installation smoothly.

Control Systems [Individual control]

Remote Control line up indoor unit wired all models remote control

RC-E4

RCH-E3 wireless indoor unit

FDT

FDTC

FDUM, FDU

FDEN remote control

RCN-T-36W-E

RCN-TC-24W-ER

RCN-KIT3-E

RCN-E1R

Wired remote control with weekly timer (option)

RC-E4

Run hour meters to facilitate maintenance checking

RC-E4 stores operation data when an anomaly occurs and indicates the error on the LCD. It also displays cumulative operation hours of the air conditioner and compressor since commissioning.

The RC-E4 controller enables extensive access to service and maintenance technical data combined with easy to use functions and a clear LCD display.

Room temperature controlled

by the remote control sensor

The temperature sensor is housed in the top section of the remote control unit. This arrangement has improved the sensitivity of the remote control unit’s sensor, which permits more finely controlled air conditioning.

Weekly timer function as standard

RC-E4 provides (as a standard feature) a weekly timer, which allows oneweek operation schedules to be registered. A user can specify up to four times a day to start/stop the air conditioner. (Temperature setting is also possible with the timer).

Timer operation

Changeable set temperature ranges

RC-E4 allows the upper and lower limits of a set temperature range to be specified separately.

By adjusting a set temperature range, you can ensure energy saving air conditioning by avoiding excessive cooling or heating.

Upper limit

Lower limit

Changeable range

20~30 °C(effective for heating operation)

18~26 °C(effective for non-heating operation)

Simple remote control (option)

RCH-E3 (wired)

Considering specialized usage in hotel rooms, control buttons are limited only to minimum required functions such as ON/OFF, mode, temperature setting and fan speed. It is really simple and easy to use.

RCH-E3 is not applicable to the Individual flap control system and the Flap control system.

When RCH-E3 is used, the fan has 3 speed settings (Hi-

Me-Lo) only.

Up to 16 units

It can control up to 16 units individually, with pressing the AIR CON No. button.

AUTO restart

This function allows starting the air conditioner automatically when power supply is restored after power failure or by turning on the power switch.

Wireless remote control (option)

For wireless control simply insert the infrared receiver kit on a corner of the panel.

RCN-T-36W-E,

RCN-TC-24W-ER

RCN-KIT3-E RCN-E1R

Thermistor (option)

SC-THB-E3

In case sensor in the indoor units or the remote control sensor can not sense the room temperature correctly, or individual remote control in each room is not required but only censor is required (as when center control system is in place), install SC-THB-E3 at proper place in the rooms.

When wireless remote control is used, the fan has 3 speed settings (Hi-Me-Lo) only.

37

KX6 series

SC-SL1N-E

SC-SL2NA-E

SC-SL1N-E

RAC series

(SRK/SRF-ZJX-S)

SC-BIKN-E

SC-ADNA-E

SC-ADNA-E SC-ADNA-E

Central Control

SC-SL2NA-E SC-SL3N-AE/BE

Start/stop control of up to 16 indoor units is possible either individually or collectively. With simple operations, you can effect centralized control.

PC windows central control

SC-WGWNA-A/B

(SC-WGWNA-B is with electric power calculation function)

Centralized control of up to 64 indoor units. It can allow connection with a weekly timer without using any interface.

Easy operation realized with a large color LCD and touch panel. Up to 128 indoor units can be controlled, when three SUPERLINK-2 systems are connected.

BMS interface unit

SC-BGWN-A/B

(BACnet gateway)

(SC-WGWN-B is with electric power calculation function)

SC-LGWN-A

(LonWorks gateway)

38

Up to 96 cells (some cells can have two or more indoor units and total number of indoor units can be up to 128 units) are controlled from the Internet Explorer.

Additional engineering service cost etc. is required. Please consult your dealer when using this central control.

Up to 96 cells (some cells can have two or more indoor units and total number of indoor units can be up to 128 units) are controlled centrally from a BMS.

Additional engineering service cost etc. is required.

In case of SC-BGWN-B, communication test by qualified person regarding electric cost calculation function is required before commissioning. Please consult your dealer when using this gateway.

Up to 96 indoor units (48 indoor unit x 2) are linked as an open network! Centrally controlled through LonWorks!

Additional engineering service cost etc. is required. Please consult your dealer when using this gateway.

SUPERLINK E BOARD (SC-ADNA-E)

This board is used when conducting control of the single package (wired remote control unit) 1-type series using a network option (SC-SL1N-E, SC-SL2NA-E, etc).

(1) Functions

(a) Transmits the settings from the network option to the indoor units.

(b) Returns the priority indoor unit data in response to a data request from the network option.

(c) Inspects the error status of connected indoor units and transmits the inspection codes to the network option.

(d) A maximum of 16 units can be controlled (if in the same operation mode).

(2) Wiring connection diagram

SL E board

X

Y

A

B

ON

OFF SW3

SW1 SW2

Master/Sub address

Network address setting switches

[000]-(127)

Blue

Blue

Black

White

X

Y

A

B

Connected to the terminals for

Superlink signal lines

MVVS 0.75 - 1.25mm

2

Connected to the remote controller terminals (no polarity) (the length should be 600 m or shorter)

200 m or shorter

300 m or shorter

400 m or shorter

600 m or shorter

0.5 mm 2 x 2 cores

0.75 mm

1.25 mm

2.0 mm 2

2

2

x 2 cores

x 2 cores

x 2 cores

Basic Connections

Outdoor unit

Internal/external Crossing

Indoor unit

X Y

SL E Board

X Y

A B

Network options

A B

Remote control

X Y

Plural Controls by Multiple Remote Controls. Mixture of Multiple Units

Outdoor unit

Internal/external Crossing

Inside Inside Inside Inside

SL E

Board

Network options

R R

• Transmit the information of plural “Master” units to the network.

• Transmit the abnormalities of the “Slave” units to the network.

Setting the plural “Master/Slave” units with the dip SW of the printed circuit board.

Setting the “Master/Slave” remote controls with the dip SW of the remote control board.

Plural Controls by Multiple Remote Controls. Mixture of Multiple Units Without Remote Control Wireless Kit

Outdoor unit

Internal/external Crossing

Inside Inside Inside Inside

Outdoor unit

Internal/external Crossing

Inside Inside Inside

SL E

Board

Network options

R R SL E

Board

R R

Set up “000” to “127” using address switch on the SL E board.

Outdoor unit

Internal/external Crossing

Inside Inside

SL E

Board

Network options

Set the SL E board dip SW to “Master” SW3-1 ON.

The network option SLA-1-

E, SL1N-E is not allowed

(This will disturb switching of the operation mode)

Outdoor unit

Internal/external Crossing

Inside Inside

SL E

Board

Network options

Wireless Kit

Wireless remote control

(3) Metal box dimension

85

40 22.5

35

30

2-ø6

39

KX6 series

SC-SL1N-E

SC-SL2NA-E

SC-SL1N-E

RAC series

(SRK/SRF-ZJX-S)

SC-BIKN-E

SC-ADNA-E

SC-ADNA-E SC-ADNA-E

Central Control

SC-SL2NA-E SC-SL3N-AE/BE

Start/stop control of up to 16 indoor units is possible either individually or collectively. With simple operations, you can effect centralized control.

PC windows central control

SC-WGWNA-A/B

(SC-WGWNA-B is with electric power calculation function)

Centralized control of up to 64 indoor units. It can allow connection with a weekly timer without using any interface.

Easy operation realized with a large color LCD and touch panel. Up to 128 indoor units can be controlled, when three SUPERLINK-2 systems are connected.

BMS interface unit

SC-BGWN-A/B

(BACnet gateway)

(SC-WGWN-B is with electric power calculation function)

SC-LGWN-A

(LonWorks gateway)

38

Up to 96 cells (some cells can have two or more indoor units and total number of indoor units can be up to 128 units) are controlled from the Internet Explorer.

Additional engineering service cost etc. is required. Please consult your dealer when using this central control.

Up to 96 cells (some cells can have two or more indoor units and total number of indoor units can be up to 128 units) are controlled centrally from a BMS.

Additional engineering service cost etc. is required.

In case of SC-BGWN-B, communication test by qualified person regarding electric cost calculation function is required before commissioning. Please consult your dealer when using this gateway.

Up to 96 indoor units (48 indoor unit x 2) are linked as an open network! Centrally controlled through LonWorks!

Additional engineering service cost etc. is required. Please consult your dealer when using this gateway.

SUPERLINK E BOARD (SC-ADNA-E)

This board is used when conducting control of the single package (wired remote control unit) 1-type series using a network option (SC-SL1N-E, SC-SL2NA-E, etc).

(1) Functions

(a) Transmits the settings from the network option to the indoor units.

(b) Returns the priority indoor unit data in response to a data request from the network option.

(c) Inspects the error status of connected indoor units and transmits the inspection codes to the network option.

(d) A maximum of 16 units can be controlled (if in the same operation mode).

(2) Wiring connection diagram

SL E board A

B

X

Y

ON

OFF SW3

SW1 SW2

Master/Sub address

Network address setting switches

[000]-(127)

Blue

Blue

Black

White

X

Y

A

B

Connected to the terminals for

Superlink signal lines

MVVS 0.75 - 1.25mm

2

Connected to the remote controller terminals (no polarity) (the length should be 600 m or shorter)

200 m or shorter

300 m or shorter

400 m or shorter

600 m or shorter

0.5 mm 2 x 2 cores

0.75 mm

1.25 mm

2.0 mm 2

2

2

x 2 cores

x 2 cores

x 2 cores

Basic Connections

Outdoor unit

Internal/external Crossing

Indoor unit

X Y

SL E Board

X Y

A B

Network options

A B

Remote control

X Y

Plural Controls by Multiple Remote Controls. Mixture of Multiple Units

Outdoor unit

Internal/external Crossing

Inside Inside Inside Inside

SL E

Board

Network options

R R

• Transmit the information of plural “Master” units to the network.

• Transmit the abnormalities of the “Slave” units to the network.

Setting the plural “Master/Slave” units with the dip SW of the printed circuit board.

Setting the “Master/Slave” remote controls with the dip SW of the remote control board.

Plural Controls by Multiple Remote Controls. Mixture of Multiple Units Without Remote Control Wireless Kit

Outdoor unit

Internal/external Crossing

Inside Inside Inside Inside

Outdoor unit

Internal/external Crossing

Inside Inside Inside

SL E

Board

Network options

R R SL E

Board

R R

Set up “000” to “127” using address switch on the SL E board.

Outdoor unit

Internal/external Crossing

Inside Inside

SL E

Board

Network options

Set the SL E board dip SW to “Master” SW3-1 ON.

The network option SLA-1-

E, SL1N-E is not allowed

(This will disturb switching of the operation mode)

Outdoor unit

Internal/external Crossing

Inside Inside

SL E

Board

Network options

Wireless Kit

Wireless remote control

(3) Metal box dimension

85

40 22.5

35

30

2-ø6

39

40

OUTDOOR UNIT DIMENSIONS

FDC100VNX, 100VSX, 125VNX, 125VSX,

140VNX, 140VSX (unit:mm)

113

46

B

A

Terminal block

Mark

A

B

C

D

E

F

Item

Service valve connection of the attached connecting pipe(gas side)

Service valve connection(liquid side)

Pipe/cable draw-out hole

Drain discharge hole

Anchor bolt hole

Cable draw-out hole

ø15.88(5/8")(Flare)

ø9.52(3/8")(Flare)

ø20x3places

M10x4places

ø30x2places(front)

ø45(side)

ø50(back)

Notes:

(1) It must not be surrounded by walls on the four sides.

(2) The unit must be fixed with anchor bolts. An anchor bolt must not protrude more than

15mm.

(3) Where the unit is subject to strong winds, lay it in such a direction that the blower outlet faces perpendicularly to the dominant wind direction.

(4) Leave 1m or more space above the unit.

(5) A wall in front of the blower outlet must not exceed the units height.

(6) The model name label is attached on the lower right corner of the front panel.

(7) Connect the Service valve with local pipe by using the pipe of the attachment. (Gas side only)

B

A

F F C

60

970

190

60

E

580

C

50

55

15

200

60 15

262 388

D

SRC40ZIX-S, 50ZIX-S, 60ZIX-S (unit:mm)

C

52

27 50

C

L2

L3

Intake

L4

Intake

L1

Service space

Outlet

Minimum installation space

15

50

50

F

Dimensions

L

1

L

2

L

3

L

4

Examples of

installation

1

Open

300

150

5

2

Open

5

300

5

3

500

Open

150

5

Terminal block

327.3

D

50.6

12

89

327.3

510

800

201

17.9

E

71.2

148.4

Check joint

33.5

40

°

40

°

B

A

Intake

L2 Intake

L3

L4

outlet

L1

Examples of

installation

Dimensions

L

1

L

2

L

3

L

4

1

Open

100

100

250

2

280

75

80

Open

3

280

Open

80

250

Mark

A

B

D

E

Drain discharge port

Anchor bolt hole

Item

Refrigerant gas side pipe connection tap

Refrigerant liquid side pipe connection tap

ø12.7(flare)

ø6.35(flare)

ø20.5x5places

M10x4places

Notes:

(1) It must not be surrounded by walls on the four sides.

(2) The unit must be fixed with anchor bolts.An anchor bolt must not protrude more than

15mm.

(3) Where the unit is subject to strong winds, lay it in such a direction that the blower outlet faces perpendicularly to the dominant wind direction.

(4) Leave a 1m or larger space above the unit.

(5) A wall in front of the blower outlet must not exceed the units height.

(6) The unit name plate is attached on the lower right corner of the front panel.

FDC71VNX (unit:mm)

2-R7.5

223 310

61

150

D

580

880

60

15

E

B

C

D

E

Mark

A

Item

Service valve connection

(gas side)

Service valve connection

(liquid side)

Pipe/cable draw-out hole

Drain discharge hole

Anchor bolt hole

ø15.88(5/8")

(Flare)

ø9.52(3/8")

(Flare)

ø20x3places

M10x4places

Notes:

(1) It must not be surrounded by walls on the four sides.

(2) The unit must be fixed with anchor bolts. An anchor bolt must not protrude more the 15mm.

(3) Where the unit is subject to strong winds, lay it in such a direction that the blower outlet faces perpendicularly to the dominant wind direction.

(4) Leave 1m or more space above the unit.

(5) A wall in front of the blower outlet must not exceed the units height.

(6) The model name label is attached on the lower right corner of the front.

150

88

27

32

Terminal block

Intake

L2

Intake outlet

Minimum installation space

L4

B

30

30

C

A

Examples of

installation

Dimensions

L

1

L

2

L

3

L

4

1 2

Open

300

100

250

Open

250

150

250

3

500

Open

100

250

165.5

25

FDC100VN, 125VN, 140VN

100VS, 125VS, 140VS (unit:mm)

40

100

B

Terminal block

B

A

A

B

E

F

C

D

Mark

A

Item

Refrigerant gas side pipe connection tap

Refrigerant liquid side pipe connection tap

Pipe/cable draw-out port

Drain discharge port

Anchor bolt hole

Cable draw-out port

ø15.88(flare)

ø9.52(flare)

ø20.3x3places

M10x4places

ø30.3x3places

Notes:

(1) It must not be surrounded by walls on the four sides.

(2) The unit must be fixed with anchor bolts.An anchor bolt must not protrude more than 15mm.

(3) Where the unit is subject to strong winds, lay it in such a direction that the blower outlet faces perpendicularly to the dominant wind direction.

(4) Leave a 1m or larger space above the unit.

(5) A wall in front of the blower outlet must not exceed the units height.

(6) The unit name plate is attached on the lower right corner of the front panel.

A

F

F

E

60

190

60

970

C

580

50

55

15

200

60 15

262 388

D

C

52

27 50

C

L2

Intake

L1

L3 Intake outlet

L4

Minimum installation space

C

15

40

50

VIEW A

Examples of

installation

Dimensions

L

1

L

2

L

3

L

4

1 2

Open

300

150

5

Open

5

300

5

3

500

Open

150

5

41

40

OUTDOOR UNIT DIMENSIONS

FDC100VNX, 100VSX, 125VNX, 125VSX,

140VNX, 140VSX (unit:mm)

113

46

B

A

Terminal block

Mark

A

B

C

D

E

F

Item

Service valve connection of the attached connecting pipe(gas side)

Service valve connection(liquid side)

Pipe/cable draw-out hole

Drain discharge hole

Anchor bolt hole

Cable draw-out hole

ø15.88(5/8")(Flare)

ø9.52(3/8")(Flare)

ø20x3places

M10x4places

ø30x2places(front)

ø45(side)

ø50(back)

Notes:

(1) It must not be surrounded by walls on the four sides.

(2) The unit must be fixed with anchor bolts. An anchor bolt must not protrude more than

15mm.

(3) Where the unit is subject to strong winds, lay it in such a direction that the blower outlet faces perpendicularly to the dominant wind direction.

(4) Leave 1m or more space above the unit.

(5) A wall in front of the blower outlet must not exceed the units height.

(6) The model name label is attached on the lower right corner of the front panel.

(7) Connect the Service valve with local pipe by using the pipe of the attachment. (Gas side only)

B

A

F F C

60

970

190

60

E

580

C

50

55

15

200

60 15

262 388

D

SRC40ZIX-S, 50ZIX-S, 60ZIX-S (unit:mm)

C

52

27 50

C

L2

L3

Intake

L4

Intake

L1

Service space

Outlet

Minimum installation space

15

50

50

F

Examples of

installation

Dimensions

L

1

L

2

L

3

L

4

1

Open

300

150

5

2

Open

5

300

5

3

500

Open

150

5

Terminal block

327.3

D

50.6

12

89

327.3

510

800

201

17.9

E

71.2

148.4

Check joint

33.5

40

°

40

°

B

A

Intake

L2 Intake

L3

L4

outlet

L1

Examples of

installation

Dimensions

L

1

L

2

L

3

L

4

1

Open

100

100

250

2

280

75

80

Open

3

280

Open

80

250

Mark

A

B

D

E

Drain discharge port

Anchor bolt hole

Item

Refrigerant gas side pipe connection tap

Refrigerant liquid side pipe connection tap

ø12.7(flare)

ø6.35(flare)

ø20.5x5places

M10x4places

Notes:

(1) It must not be surrounded by walls on the four sides.

(2) The unit must be fixed with anchor bolts.An anchor bolt must not protrude more than

15mm.

(3) Where the unit is subject to strong winds, lay it in such a direction that the blower outlet faces perpendicularly to the dominant wind direction.

(4) Leave a 1m or larger space above the unit.

(5) A wall in front of the blower outlet must not exceed the units height.

(6) The unit name plate is attached on the lower right corner of the front panel.

FDC71VNX (unit:mm)

2-R7.5

223 310

61

150

D

580

880

60

15

E

B

C

D

E

Mark

A

Item

Service valve connection

(gas side)

Service valve connection

(liquid side)

Pipe/cable draw-out hole

Drain discharge hole

Anchor bolt hole

ø15.88(5/8")

(Flare)

ø9.52(3/8")

(Flare)

ø20x3places

M10x4places

Notes:

(1) It must not be surrounded by walls on the four sides.

(2) The unit must be fixed with anchor bolts. An anchor bolt must not protrude more the 15mm.

(3) Where the unit is subject to strong winds, lay it in such a direction that the blower outlet faces perpendicularly to the dominant wind direction.

(4) Leave 1m or more space above the unit.

(5) A wall in front of the blower outlet must not exceed the units height.

(6) The model name label is attached on the lower right corner of the front.

150

88

27

32

Terminal block

Intake

L2

Intake outlet

Minimum installation space

L4

B

30

30

C

A

Examples of

installation

Dimensions

L

1

L

2

L

3

L

4

1 2

Open

300

100

250

Open

250

150

250

3

500

Open

100

250

165.5

25

FDC100VN, 125VN, 140VN

100VS, 125VS, 140VS (unit:mm)

40

100

B

Terminal block

B

A

A

B

E

F

C

D

Mark

A

Item

Refrigerant gas side pipe connection tap

Refrigerant liquid side pipe connection tap

Pipe/cable draw-out port

Drain discharge port

Anchor bolt hole

Cable draw-out port

ø15.88(flare)

ø9.52(flare)

ø20.3x3places

M10x4places

ø30.3x3places

Notes:

(1) It must not be surrounded by walls on the four sides.

(2) The unit must be fixed with anchor bolts.An anchor bolt must not protrude more than 15mm.

(3) Where the unit is subject to strong winds, lay it in such a direction that the blower outlet faces perpendicularly to the dominant wind direction.

(4) Leave a 1m or larger space above the unit.

(5) A wall in front of the blower outlet must not exceed the units height.

(6) The unit name plate is attached on the lower right corner of the front panel.

A

F

F

E

60

190

60

970

C

580

50

55

15

200

60 15

262 388

D

C

52

27 50

C

L2

Intake

L1

L3 Intake outlet

L4

Minimum installation space

C

15

40

50

VIEW A

Examples of

installation

Dimensions

L

1

L

2

L

3

L

4

1 2

Open

300

150

5

Open

5

300

5

3

500

Open

150

5

41

OUTDOOR UNIT DIMENSIONS

FDC200VS (unit:mm)

42

FDC250VS (unit:mm)

MEMO

43

OUTDOOR UNIT DIMENSIONS

FDC200VS (unit:mm)

42

FDC250VS (unit:mm)

MEMO

43

Before starting use

Heating performance

The heating performance values (kW) described in catalog are the values obtained by operating at an outdoor temperature of 7 C and indoor temperature of 20 C as set forth in the ISO Standards. As the heating performance decreases as the outdoor temperature drops, if the outdoor temperature is too low and the heating performance is insufficient, use other heating appliances as well.

Indication of sound values

The sound values are the values (A scale) measured in a chamber such as an anechoic chamber following the ISO Standards. In the actual installation state, the value is normally larger than the values given in the catalog due to the effect of surrounding noise and echo. Take this into consideration when installing.

Use in oil atmosphere

Avoid installing this unit in as atmosphere where oil scatters or builds up, such as in a kitchen or machine factory.

If the oil adheres to the heat exchanger, the heat exchanging performance will drop, mist may be generated, and the synthetic resin parts may deform and break.

Use in acidic or alkaline atmosphere

If this unit is used in acidic atmosphere such as hot spring areas having high level of sulfuric gases or in alkaline atmosphere including ammonia or calcium chloride, places where the exhaust of the heat exchanger is sucked in, or at coastal areas where the unit is subject to salt breezes, the outer plate or heat exchanger, etc., will corrode. Please ask a dealer or specialist when you use an air conditioner in places differing from a general atmosphere.

Use in places with high ceilings

If the ceiling is high, install a circulator to improve the heat and air flow distribution when heating.

Refrigerant leakage

The refrigerant (R410A) used for Air conditioner is non-toxic and inflammable in its original state.

However, in consideration of a state where the refrigerant leaks into the room, measures against refrigerant leaks must be taken in small rooms where the tolerable level could be exceeded. Take measures by installing ventilation devices, etc.

Use in snowy areas

Take the following measures when installing the outdoor unit in snowy areas.

·Snow prevention

Install a snow-prevention hood so that the snow does not obstruct the air intake port or enter and freeze in the outdoor unit.

·Snow piling

In areas with heavy snow fall, the piled snow could block the air intake port. In this case, a frame that is 50cm or higher than the estimated snow fall must be installed underneath the outdoor unit.

Automatic defrosting device

If the temperature is low, and the humidity is high, frost will stick to the heat exchanger of the outdoor unit. If use is continued, the heating performance will drop.

The "Automatic defrosting device" will function to remove this frost.

After heating for approx, three to ten minutes, it will stop, and the frost will be removed. After defrosting, hot air will be blown again.

Servicing the air-conditioner

After the air-conditioner is used for several seasons, dirt will build up in the air-conditioner causing the performance to drop. In addition to regular servicing, we recommend the maintenance contract (charged for) by a specialist.

Safety Precautions

Air-conditioner usage target

The air-conditioner described in this catalog is a dedicated cooling/heating device for human use.

Do not use it for special applications such as the storage of foodstuffs, animals or plants, precision devices or valuable art, etc.

This could cause the quality of the items to drop, etc.

Do not use this for cooling vehicles or ships. Water leakage or current leaks could occur.

Before use

Always read the "User,s Manual" thoroughly before starting use.

Installation

Always commission the installation to a dealer or specialist. Improper installation will lead to water leakage, electric shocks and fires.

Make sure that the outdoor unit is stable in installation. Fix the unit to stable base.

Usage place

Do not install in places where combustible gas could leak or where there are sparks.

Installation in a place where combustible gas could be generated, flow or accumulate, or places containing carbon fibers could lead to fires.

Our factories are ISO9001 and ISO14001 certified.

Certified ISO 9001 Certified ISO 14001

BIWAJIMA PLANT

Mitsubishi Heavy Industries, Ltd.

Air-conditioning & Refrigeration Systems Headquarters

Certificate number : JQA-0709

MITSUBISHI HEAVY INDUSTRIES-

MAHAJAK AIR CONDITIONERS CO., LTD.

Certificate Number : 04100 1998 0813

Mitsubishi Heavy

Industries-Haier (Quingdao)

Air-conditioners Co.,Ltd.

Certificate Number : 5170-1996-AQ-RCG-RvA

Certificate 04104 1998 0813 E5

BIWAJIMA PLANT

Mitsubishi Heavy Industries, Ltd.

Air-conditioning & Refrigeration Systems Headquarters

Certificate number : JQA-EM0256

MITSUBISHI HEAVY INDUSTRIES-

MAHAJAK AIR CONDITIONERS CO.,LTD.

Certificate Number : 04104 1998 0813 E5

Mitsubishi Heavy

Industries-Haier (Quingdao)

Air-conditioners Co.,Ltd.

Certificate number : 01-1998-083

Japan Head Office:

Mitsubishi Heavy Industries Ltd

16-5 2-Chome Kounan Minato-ku Tokyo

108-8215, Japan www.mhi.co.jp

HB91-10P01E-A-0 February 2010(3B)R

Because of our policy of continuous improvement, we reserve right to make changes in all specifications without notice.

Printed in Japan

High Performance Air-Conditioning

FD

series

Inverter Packaged Air-Conditioners

50/60Hz

10P01E-A-0

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement