Epson P07303 Stand Alone VFD Pole Display User's manual
Epson P07303 is a standalone VFD pole display with a 20-column x 2-line blue-green vacuum fluorescent display. It supports 96 alphanumeric characters, 13 international character sets, and user-defined characters. With its RS-232C interface and baud rate ranging from 4800 to 38400 bps, it can easily connect to various devices. The Epson P07303 also boasts a window function for controlling the display area, brightness adjustment, cursor control, and user-defined character storage.
Publicitate
Publicitate
USER’S MANUAL
P07303 Stand Alone VFD Pole Display
48200550
(January,2002 V1.0)
FCC Notice
Federal Communications Commission (FCC) Radio Frequency
Interference Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
COPYRIGHT & TRADMARK
All rights reserved. The information contained in this guide has been validated and reviewed for accuracy. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this guide, the Manufacturer assumes no responsibility for errors or omissions.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of
Manufacturer.
General Notice: All the company names used herein are for identification purposes only and may be trademarks of their respective companies.
NOTICE
The contents of this manual are subject to change without notice.
P07303 Stand Alone VFD Customer Display
Copyright of Manufacture
December 2001 (Reversion 1.0)
Part No. 48200550 i
Contents
1. Features....................................................................................................... 1
2. General Specification................................................................................... 2
3 Unpacking and Checking the Parts .............................................................. 3
4. Interface....................................................................................................... 4
4.1 Specifications ................................................................................ 4
4.2 The communication flow ............................................................... 4
4.3. Interface ....................................................................................... 5
4.3.1 Stand alone VFD Pole Display.............................................. 5
5. Dip Switch and Software Setting ................................................................. 7
5.1 Command type selection............................................................... 7
5.2 Baud rate selection ....................................................................... 7
5.3 Parity check selection ................................................................... 7
5.4 Demo Mode selection ................................................................... 7
5.5 International character set ............................................................ 8
5.6 Self-test ......................................................................................... 8
5.7. Software Status Setting................................................................ 9
5.7.1. Baud rate ................................................................................. 9
5.7.2 International character set ........................................................ 9
5.7.3 Command type select ............................................................. 10
5.7.4 Reset EEPROM.......................................................................11
5.7.5 Save data for demo display .....................................................11
5.7.6 Run Demo message ................................................................11
5.7.7 Set Communication parity....................................................... 12
5.7.8 Show VFD Firmware Version.................................................. 12
5.7.9 Save title data to EEPROM .................................................... 12
6. Command List Table.................................................................................. 13
7. Command .................................................................................................. 15
7.1. POS7300 series command set .................................................. 15
7.2 CD5220 Standard Mode Command List ..................................... 16
7.3 UTC standard mode command list ............................................. 18
7.4 UTC enhanced mode command list............................................ 19
7.5 AEDEX mode command list........................................................ 19
7.6 ADM787/788 mode command list ............................................... 20
7.7 DSP-800 mode command list ..................................................... 20
7.8 EPSON ESC/POS command list-1 ............................................. 21
8. Character Set ............................................................................................ 23
8.1 International Character Sets ..................................................... 23
8.2 USA, Standard Character Sets (20H – 7EH) .............................. 23
8.3 Page 0 (PC437: USA, Standard Europe) (80H – FFH)............... 24
8.4 Page 1 (Katakana) (80H – FFH) ................................................. 24
8.5 Page 2 (PC850: Mulitlingual) (80H – FFH) ................................. 24 ii
8.6 Page 3 (PC860: Portuguese) (80H – FFH)................................. 25
8.7 Page 4 (PC863: Canadian-French) (80H – FFH) ....................... 25
8.8 Page 5 (PC865: Nordic) (80H – FFH)......................................... 26
8.9 Page 6 (Slavonic) (80H – FFH)................................................... 26
8.10 Page 7 (Russia) (80H – FFH) ................................................... 27
9.Command details........................................................................................ 28
9.1 Overwrite mode........................................................................... 28
9.2 Vertical scroll mode ..................................................................... 28
9.3 Horizontal scroll mode................................................................. 28
9.4 Set the string display mode, and write string to display.............. 28
9.5 Upper line message scroll continuously...................................... 28
9.7 Move cursor right ........................................................................ 28
9.8 Move cursor up ........................................................................... 29
9.9 Move cursor down....................................................................... 29
9.10 Move cursor to home position................................................... 29
9.11 Move cursor to left-most position .............................................. 29
9.12 Move cursor to right-most position............................................ 29
9.13 Move cursor to bottom position................................................. 29
9.14 Move cursor to specified position.............................................. 29
9.15 Initialize display ......................................................................... 29
9.16 Reset the window...................................................................... 29
9.17 Clear display screen, and clear string mode............................. 30
9.18 Clear current line, and cancel string mode ............................... 30
9.19 Brightness adjustment............................................................... 30
9.20 Set cursor ON or OFF............................................................... 30
9.21 Set user-defined characters...................................................... 30
9.22 Reset user defined character set .............................................. 30
9.23 Cancel user defined characters ................................................ 30
9.24 Store the user defined character into EEPROM ....................... 30
9.25 Restore the user defined character from EEPROM.................. 30
9.26 Character font format ................................................................ 31
10. Control code set ...................................................................................... 31
Appendix A: Display Module Dimension........................................................ 32 iii
1. Features
(1) Data can be display on 20 columns x 2 lines.
(2) Blue–green color and large character are easy to see
(3)The DIP switches setting emulate commands mode, baud rate and international character.
(4) Command emulation modes include POS7300/ CD5220 II/ ADM787/ UTC / AEDEX/ Epson/ DSP800.
(5) User’s-defined character and message can be downloaded.
(6) Display area can be controlled by window function.
(7) Provides an interface based in RS-232C, and RS232C baud rate from 4800 to 38400 bps.
(8) Reverse characters can be specified using the Epson command set.
(9) Support software has facility for designing user-defined characters and downloading setup parameters to the display.
10.) The other option interface RS485 can link max. 256 display by one port.
11.) Provides pass through function, so both printer and display can be connected to the same port.
1
2. General Specification
NO ITEM
1 Display method
2
3
4
5
7
Number of character
Character font
Display color
Brightness
Character size
9 Power consumption
10 MTBF
11 Panel dimensions
14 Viewing angle
15 Rotation angle
16 Weight
17 Operating temperature
19 Storage Temperature
Descriptions
Vacuum fluorescent display
40 characters
( 20 columns x 2 lines)
5 x 7 Dot matrix
Blue green
700 cd /
96 alphanumeric
13 kinds of international character set
1 kind of user define character
9.0mm x 5.25mm
9-35VDC
3 - 6 W
25000 hours (power on time)
224 (W) x 93 (H) x 50(D) mm
Long support : 22 cm
Short support : 9 cm
190(w)x55(h)x96(d)mm
-5 - 60 degrees
Maximum 270 degrees
5 - 45
30%-85%
-10 - 55
10%-85%
2
3 Unpacking and Checking the Parts
G
225 mm
93 mm
•Pole Display Module
•Flat Cable (DB-9P to DB-9P flat cable connector )
•Base Unit
•Two pieces of pole support (1x22cm, 1x9cm)
•Installation guide
•Power Adapter
3
4. Interface
4.1 Specifications
Data transmission: Serial
Synchronization: Asynchronous
Handshaking: DTR / DSR
Signal level:
MARK = -3 to –15 V (logic “1”)
SPACE = +3 to +15 V (logic “0”)
Baud rates: 4800,9600,19200,38400 bps
Bit length:
Stop bits:
8 bits
1 or more
4.2 The communication flow
Data flow :
Handshaking flow :
PC/host to display, Display to printer, Printer to
PC/host
Display to PC/host, printer to display,
PC/host to printer
Customer display
Host computer
Receipt printer
Control connecting direction
Data connecting direction
Note: There are 200 bytes resident buffer in the display for pass data to printer. If PC/host keep transmitting the data to printer when the display inactive DTR or RTS , data will be lost.
4
4.3. Interface
4.3.1 Stand alone VFD Pole Display
Below illustrate the configuration of Stand alone VFD Pole
Display base.
Figure of VFD Pole Display Base
●Interface connector on the bottom of Pole Display Base (standard )
CN2 CN3 CN6
● Interface connector on the bottom of Pole Display Base (option )
CN6 CN5 CN4 CN3 CN2 CN1
CN2:Power input connector from adapter ( range from 9-35VDC,
Manufacture offer +12V power adapter )
CN3: RS-232C connect to printer (Reserved )
CN4: Connect to display panel
CN5: RS-232C connect to PC/Host
CN1,CN6: 24Vdc power supply pass-through connects (option)
5
CN2: RS-232C connects to PC/Host
CN3: Connect to display panel
CN6: Power supply connector
CN1,CN4, CN5: No used
Power Supply Connectors
CN6 / Connector type: DC jack (5.5/2.1)
Pin assignment
No Signal
+ Vin
- GND
RS232C link to PC/HOST connector
CN2 / Connector type: D-sub 9 pin female
Pin assignment
5 1
6 1
9 6
6
8
No Signal Direction
2
3
RXD
TXD
From PC/Host to display
From printer to PC/Host
4 DSR From PC/Host to printer
5 GND -
DSR
DSR
From display to PC/Host
From display to PC/Host
Receive data
Printer status data
PC/Host ready signal
Display/printer ready signal
Display/printer ready signal
RS232C link to printer connector
CN1 / Connector type: Phone-jack 10P/8C
Pin assignment
10 1
No Signal Direction
4,5 GND -
6 DTR From PC/Host to printer
7 DSR From printer to display
8
9
TXD From display to printer
RXD From printer to PC/Host
PC/Host ready signal
Printer ready signal
Printing data
Printer status data
Display penal connector
CN3 / Connector type: Phone-jack 10P/8C
Pin assignment
No Signal Direction
2,3 Vin -
4,5 GND -
6 DSR From Printer to Display
7 DTR From Display to PC/Host
8
9
RXD From PC/Host to Display
TXD From Display to Printer
Power 9 – 33 Vdc
10 1
Printer ready signal
Display ready signal
Display/Printing data signal
Printer status data signal
6
5. Dip Switch and Software Setting
5.1 Command type selection
ON ON ON POS7300
OFF ON ON ESC/POS
OFF OFF ON DSP800
ON ON OFF AEDEX
OFF ON OFF UTC/P
ON OFF OFF UTC/S
OFF OFF OFF CD5220
5.2 Baud rate selection
SW8 SW9 Baud rate (bps)
ON ON 4800
OFF ON 9600
ON OFF 19200
OFF OFF 38400
5.3 Parity check selection
Default
ON None-parity
OFF Even-parity
5.4 Demo Mode selection
SW11 Show demo string Default
ON Enable
OFF Disable
7
5.5 International character set
SW4 SW5 SW6 SW7 Character set Code table ( 80H-FFH)
ON ON ON ON
*default
U.S.A.
PC-437(USA, standard
Europe)
OFF ON ON ON FRANCE PC-850(multilingual)
ON OFF ON ON GERMANY PC-850(multilingual)
OFF OFF ON ON U.K. PC-850(multilingual)
ON ON OFF ON DENMARK PC-850(multilingual)
OFF ON OFF ON SWEDEN
ON OFF OFF ON ITALY
PC-850(multilingual)
PC-850(multilingual)
OFF OFF OFF ON SPAIN
ON ON ON OFF JAPAN
OFF ON ON OFF NORWAY
PC-850(multilingual)
Katakana
PC-850(multilingual)
OFF OFF ON OFF SLAVONIC
ON ON OFF OFF RUSSIA
OFF ON OFF OFF U.S.A
OFF OFF OFF OFF Used define pattern from EEPROM
5.6 Self-test
SW11 function
ON Power on self-test
* SW12 is reserve
8
5.7. Software Status Setting
When system POWER ON, there is no need to turn off to modify Command Type, Baud Rate, Parity,
Demo Mode and International Character. To re-set DIP Switch to various Command Type under the following list of Command to modify the setting. The setup value will stored in the EEPROM.
When DIP Switch is OFF. Next time the system POWER ON previous setup value will be the default value and no need to modify.
5.7.1. Baud rate
STX 05 B n ETX /Set baud rate and keep it with EEPROM/
ASCII Format STX 05 B n ETX
Dec. Format [02][05][66] n [03]
Hex. Format [02h][05h][42h] n [03h] 30h n 34h
Description Change the display communication baud rate. The baud rate setting can be selected from 4800 to 38400.
30h 4800
31h 9600
32h 19200
33h 38400
5.7.2 International character set
STX 05 S n ETX /Change international character set/
ASCII Format STX 05 S N ETX
Dec. Format [02][05][83] n [03]
Hex. Format [02h][05h][53h] n [03h] 30h n 3fh
Description Change the display international character font .A total of 16 different character fonts to select from. The setting function will be saved to EEPROM.
9
N nternational font
30h .S.A.
31h RANCE
33h .K.
34h DENMARK I
35h WEDEN n nternational font
38h APAN
39h ORWAY
3Bh LAVONIC
3Ch RUSSIA
3Dh .S.A.
37h PAIN 3Fh ser define pattern
5.7.3 Command type select
STX 05 C n ETX /Change command type/
ASCII Format STX 05 C n ETX
Dec. Format [02][05][67] n [03]
Hex. Format [02h][05h][43h] n [03h] 30h n 37h
Description This command will change the command type and initialize the display.
The display emulation mode is based on
DSP800/ESC/ADM 787/POS7301/AEDEX/UTC/CD5220 mode. The setting function will be saved to EEPROM.
N Command type n Command type
10
5.7.4 Reset EEPROM
STX 05 07 n ETX /Reset EEPROM/
ASCII Format STX 05 07 n ETX
Dec. Format [02][05][07][n][03]
Hex. Format [02h][05h][07h][n][03h]
Description This command will reset the content of EEPROM (e.g. Demo scroll data, user-define character)
N Description
31h Clear all EEPROM contents
32h Clear upper line data message
33h Clear lower line data message
5.7.5 Save data for demo display
STX 05 L n m ETX /Save demo message to EEPROM/
ASCII Format STX 05 L n m ETX
Dec. Format [02][05][76] n m [03]
Hex. Format [02h][05h][4Ch] n m [03h]
Description Save demo message for upper line and bottom line n = 31h save data message for upper line n = 32h save data message for lower line m = data message ; the maximum data character is under 200
5.7.6 Run Demo message
STX 05 L n m ETX /Run demo message/
ASCII Format STX 05 D 08 ETX
Dec. Format [02][05][68][08][03]
Hex. Format [02h][05h][44h][08][03h]
Description Run demo message for the display
11
5.7.7 Set Communication parity
STX 05 P n ETX /Parity check selection/
ASCII Format STX 05 P n ETX
Dec. Format [02][05][80] n [03]
Hex. Format [02h][05h][50h] n [03h] n=30h,31h
Description Change the display communication parity. Set 8 data bit and the parity set for even or non-parity.
30h None-parity
31h Even-parity
5.7.8 Show VFD Firmware Version
STX 05 V 01 ETX /Show VFD Firmware Version/
ASCII Format STX 05 V 01 ETX
Dec. Format [02][05][86][01][03]
Hex. Format [02h][05h][56h][01h][03h]
Description Show VFD firmware version
5.7.9 Save title data to EEPROM
STX 05 T 01 ETX /Save title data to EEPROM/
ASCII Format STX 05 T 01 ETX
Dec. Format [02][05][84][01][03]
Hex. Format [02h][05h][54h][01][03]
Description Save title data to EEPROM
12
6. Command List Table
Table –1
FLYTECH PARTNER EPSON GIGA
POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800
Move cursor right
Move cursor left
Move cursor up
Move cursor down
Move cursor to right-most position
Move cursor to left-most position
O O O
O O O
O O O
O O O
O O O
O O O
Move cursor to home position O O O
Move cursor to bottom position
O O
Move cursor to specified position
O O O
Clear display screen
O O O O O
Clear cursor line
O O O
Brightness adjustment
O O
Blink display screen
O O O
Initialize display
O O O
Select character code table
Select international character set
Select/cancel reverse character
O O
O O
O
Overwrite mode O O O O
Vertical scroll mode O O O O
Horizontal scroll mode O O O
Define download characters O O
Delete downloads characters O O
Select/cancel download character set
O O
Set/cancel the window range O O
Select peripheral device
Set starting/ending position of maro definition
O O
O
Execute and quit macro
O
Execute self-test
O O
Display time
O O O
Display time continuously
O
Display position
O
O O O O
Cursor on/off
Change to UTC enhanced mode
Change to UTC standard mode
O
O
Write string to upper line
Write string to lower line
Upper line message scroll continuously
Bottom line message scroll continuously
Message vertical down scroll continuously
Message vertical upper scroll continuously
O
O
O
Carriage return
Line feed O O
Back space O O
O O
Horizontal tab
Command type select O O
O
O
O
O
O
O
O
O
O
O
13
Table-2
Upper line message scroll once pass
Change attention code
Two line display
Clear upper line and move cursor to upper left-end position
Clear bottom line and move cursor to bottom left-end position
Set period to upper line, last n position
Set line blinking, upper line
Clear line blinking, upper line
Clear field 1 and move cursor to field 1, first position
Clear field 2 and move cursor to field 2,first position
Clear display range from n position to m position and move cursor to n position
Save the current displaying data to n layer for demo display
FLYTECH PARTNER EPSON GIGA
POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800
O
O
O
O
O
O
O
Save demo message to EEPROM O
Store the use define character into
EEPROM
Store the use define character from
EEPROM
Turn annunciator on/off
O
Specify period
O
O
Specify comma
Specify semicolon (period + comma)
O
14
7. Command
7.1. POS7300 series command set
POS7300 Standard Mode Command List
Command Code (hex)
ESC F A .. CR 1B 46 41 [DATA X 40] 0D
ESC F B .. CR 1B 46 42 [DATA X 40] 0D
ESC F D .. CR 1B 46 44 [DATA X 40] 0D
ESC F O .. CR 1B 46 4F [DATA X 40] 0D
ESC P x y 1B 50 x y
1 x 20,y=1,2
ESC _ n
ESC DC1
ESC DC2
ESC DC3
ESC @
US MD2 n
1B 5F n n=00,01
1B 11
1B 12
1B 13
1B 40
1F 02 n n=01~0Ch
US MD1 n
US DC1 n
US DC2 n
1F 01 n n=01~0Ch
1F 11 n n=’1’,’2’
1F 12 n n=’1’,’2’
US E n
NULL H
NULL K
NULL M
NULL P
NULL G
1F 45 n n=0~FFh
0 48
0 4B
0 4D
0 50
0 47
NULL O 0 4F
BS 08
HT 09
LF 0A
HOM 0B
CLR 0C
CR 0D
CAN 18
Function Description
Write string to upper line
Write string to lower line
Upper line message scroll continuously
Bottom line message scroll continuously
Move cursor to specified position
Set cursor on/off
Overwrite mode
Vertical scroll mode
Horizontal scroll mode
Initialize display
Message vertical down scroll continuously
Message vertical upper scroll continuously
Set line blinking
N=’1’ up line , n=’2’ low line
Clear line blinking
N=’1’ up line , n=’2’ low line
Blink display screen
Move cursor up
Move cursor left
Move cursor right
Move cursor down
Move cursor to left-most position
Move cursor to right-most position
Move cursor to home position
Clear display screen
Clear cursor line , and clear string mode
15
7.2 CD5220 Standard Mode Command List
Command
ESC DC1
US SOH
ESC DC2
US STX
ESC DC3
US ETX
ESC Q A .. CR
ESC Q B .. CR
ESC Q D .. CR
ESD [ D
BS
ESC [ C
HT
ESC [ A
US LF
ESC [ B
LF
ESC [ H
HOM
ESC [ L
CR
ESC [ R
US CR
ESC [ K
US B
ESC b [n]xC8
[m]xC8
ESC # n
US @
US E n
Code (hex)
1B 11
1F 01
1B 12
1F 02
1B 13
1F 03
1B 51 41 [n]x20 0D
1B 51 42 [n]x20 0D
1B 51 44 [n]xm 0D m 40
1B 5B 44
08
1B 5B 43
09
1B 5B 41
1F 0A
1B 5B 42
0A
1B 5B 48
0B
1B 5B 4C
0D
1B 5B 52
1F 0D
1B 5B 4B
1F 42
1B 62 [n]xC8h
[m]xC8h
1B 23 n (n=30~37)
1F 40
1F 45 n
Function description
Overwrite mode
Overwrite mode
Vertical scroll mode
Vertical scroll mode
Horizontal scroll mode
Horizontal scroll mode
Set the string display mode, write string to upper line.
Set the string display mode, write string to lower line.
Upper line message scroll continuously
Move cursor left
Move cursor left
Move cursor right
Move cursor right
Move cursor up
Move cursor up
Move cursor down
Move cursor down
Move cursor to home position
Move cursor to home position
Move cursor to left-most position
Move cursor to left-most position
Move cursor to right-most position
Move cursor to right-most position
Move cursor to bottom position
Move cursor to bottom position
Save demo message to
EEPROM n=Line 1; m=Line 2
Command type select
Execute self test
Blink display mode
(REMARK)
*While using command “ESC Q A” or “ESC Q B”, other commands can not be used except when using
command “CLR” or “CAN” to change operating mode.
*When using command “ESC Q D”, the upper line message will scroll continuously until a new command is received, it will then clear the upper line and move the cursor to the upper left-end position.
16
CD5220 Standard Mode Command List-2
Command
ESC I x y
US $ x y
Code (hex)
1B 6C x y / 1F 24 x y
1 x 20, y=1,2
1F 24 x y
1 x 20,y=1,2
ESC @ 1B 40
ESC W s x1 x2 y 1B 57 1 x1 x2 y
1 x1 x2 20 y=1,2
CLR
CAN
ESC * n
US X n
ESC & s n m
[a (P1…Pa)]x
(m-n+1)
ESC ? n
ESC % n
ESC _ n
ESC f n
ESC c n
ESC = n
ESC s 1
ESC d 1
0C
18
1B 2A n 1 n 4
1F 58 n 1 n 4
1B 26 1 n m
[a(p1…pa)]x (m-n+1)
20 n m FF
1B 3F n n=20h~7Fh
1B 25 n n=00,01
1B 5F n n=00,01
1B 66 n
1B 63 n
1B 3D n n=01,02,03,31,32,33
1B 73 01
1B 64 01
Function description
Move cursor to specified position
Move cursor to specified position
Initialize display
Set or cancel the window range at horizontal scroll mode
Clear display screen, and clear string mode
Clear cursor line, and clear string mode
Brightness adjustment
Brightness adjustment
Define download characters.
A=1-5 p1..p5=row1..row5
Deletes download characters.
Select/cancel download character set.
Set cursor on/off
Select international fonts
, refer *2
Select fonts,ASCII code or
JIS code, refer *3
Select peripheral device, display or printer n=01,enable printer n=02,enable display n=03,enable printer,display
Store the use define character into EEPROM
Store the use define character from EEPROM
17
*2: The parameter of international fonts set control by command
“ESC f n”
Parameter n International Font Set
‘A’ U.S.A.
‘G’ Germany
’I’ Italy
‘J’ Japan
‘U’ U.K.
‘F’ France
‘S’ Spain
‘N’ Norway
‘W’ Sweden
‘L’ Slavonic
‘R’ Russia
*3: The parameter of the code table control by command “ESC c n”
Parameter “n” International Font Set
‘J’
‘L’
‘R’
Compliance with JIS code
Compliance with SLOVONIC code
Compliance with RUSSIA code
7.3 UTC standard mode command list
Command Code (hex) Function description
DLE
DC1
10 n 0 n 28h
11
Display position
Over write display mode
DC2 12 mode
DC3 13 Cursor
DC4 14 Cursor
ESC d 1B 64 Change to UTC enhanced mode
18
7.4 UTC enhanced mode command list
Command
ESC u A .. CR
ESC u B .. CR
ESC u D .. CR
ESC u E .. CR
ESC u F .. CR
ESC u H .. CR
ESC u I .. CR
ESC RS CR
Code (hex)
1B 75 41 [data x 40]
0D
1B 75 42 [data x 40]
0D
1B 75 44 [data x 40]
0D
1B 75 45 h h ':' m m
0D h, m = '0' - '9'
1B 75 46 [data x 40]
0D
1B 75 48 n m 0D
20h n,m
1B 75 49 [data x 40]
0D
1B 0F 0D
Function description
Upper line display
Bottom line display
Upper line message scroll continuously
Display time
Upper line message scroll
Once pass
Change attention code
Two line display
Change to UTC standard mode
7.5 AEDEX mode command list
Command
! # 1 … CR
! # 2 … CR
! # 4 … CR
! # 5 … CR
! # 8 … CR
! # 9 … CR
! # 6 … CR
Code (hex)
21 23 31 [data x 40]
0D
21 23 32 [data x 40]
0D
21 23 34 [data x 40]
0D
21 23 35 h h ':' m m
0D h,m='0'-'9'
21 23 38 n m 0D
20H n,m
21 23 39 [data x 40]
0D
21 23 36 [data x 40]
0D
Function description
Upper line display
Bottom line display
Upper line message scroll
Display time
Change attention code
Two line display
Upper line message scroll once pass
19
7.6 ADM787/788 mode command list
Command Code (hex)
CLR 0C
CR 0D
SLE1 0E
Function description
SLE2
DC0
DC1
DC2
SF1
SF2
0F
10 n
11 n
12n
1E
1F
Clear upper line and move cursor to upper left-end position
Clear bottom line and move,
Cursor to bottom left-end position
Set period to upper line last n position 31H n 37H
Set line blinking, upper line n='1' up line, n='2' low line
Clear line blinking, upper line n='1' up line, n='2' low line
Clear field 1 and move cursor to field 1, first position
Clear field 2 and move cursor to field 2, first position
7.7 DSP-800 mode command list
Command
EOT SOH I n ETB
EOT SOH P n ETB
EOT SOH C n m
ETB
EOT SOH S n ETB
EOT SOH D n m
ETB
EOT SOH A n ETB
EOT SOH F n ETB
EOT SOH & n [ px5]
ETB
EOT SOH ? n ETB
EOT SOH = n ETB
EOT SOH % ETB
EOT SOH @ ETB
EOT SOH # n ETB
Code (hex)
04 01 49 n 17 n=00~0Fh or 30~3Fh
Function descriptions
Select international character set
04 01 50 n 17 n=31h-58h
04 01 43 n m 17
31h n m 58h
04 01 53 n 17 n=31h-35h
04 01 44 n m 17 n=31h-4Fh,m=31h-33h
Move cursor to specified position
Clear display range from n position to m position and move cursor to n position
Save current view message to n layer for demo view data
Display the saved demo message
04 01 41 n 17 n=31h-34h
04 01 46 n 17
00h n FFh
Brightness adjustment
Blink display Screen
04 01 26 n p1…p5 17,
20h n
Define download characters
04 01 3F n 17
20h n
04 01 3D n 17 n='1', '2', '3'
04 01 25 17
Delete download characters
Select peripheral device. n='1',enable printer n='2',enable display n='3',enable printer display
Initialize display
04 01 40 17 Execute self-test
04 01 23 n 17 ,n=30~37h Command type select
20
7.8 EPSON ESC/POS command list-1
Command
HT
BS
US LF
LF
US CR
CR
HOM
US B
US $ x y
CLR
US X n
US E n
Code (hex)
09
08
1F 0A
0A
1F 0D
0D
0B
1F 42
1F 24 x y (x=1~20, y=01,02)
0C
1F 58 n (01 n 04)
1F 45 n (n=00~ffh)
ESC @
ESC t n
ESC R n
US r n
US MD1
US MD2
US MD3
1B 40
1B 74 n (n=00-0fh)
1B 52 n (n=00-0fh)
1F 72 n (n=00,01)
1F 01
1F 02
1F 03
ESC & s n m
[a(p1..pa)]x m-n
1B 26 1 n m
[a(p1..pa)]x m-n
ESC ? n
ESC % n
20<n<=m<=ff
1B 3F n (20 n FF)
1B 25 n (n=0,30,1,31)
CAN
ESC # n
US # n m
US C n
US . n
18
1B 23 n (30h n 38h)
1F 23 n m, (n=0 or 1,0<m 20)
1F 43 n (n=1,31 then on)
US , n
US ; n
1F 2E n, n=a displayable character code
1F 2C n, n=a displayable character code
1F 3B n, n=a displayable character code
Function description
Move cursor right.
Move cursor left.
Move cursor up.
Move cursor down.
Move cursor to right–most position.
Move cursor to left-most position.
Move cursor to home position.
Move cursor to bottom position.
Move cursor to specified position.
Clear display screen.
Brightness adjustment.
Blink display screen.
Initialize display.
Select character code table.
Select international character set.
Select/cancel reverse character.
Specify overwrite mode.
Specify vertical scroll mode.
Specify horizontal scroll mode.
Define download characters.
20<n<=m<=ff a=1-5 p1 .. p5 = row1 .. row5
Delete downloads characters.
Select/cancel download character set.
Clear cursor line
Command type select
Turn annunciator on/off
Set cursor on/off
Specify period
Specify comma
Specify semicolon(period+comma)
21
EPSON Esc/pos command list-2
Command Code (hex)
ESC W n s x1 y1 x2 y2 1 B 57 n s x1 y1 x2 y2
ESC = n n=1,2,3,4 s=0,1
1B 3D n
US : n=1,31,select printer n=2,32,select display n=3,33, select printer, display
1F 3A
Function description
Specify/cancel the window range.
1<=x1<=x2<=20
1<=y1<=y2<=2
Select peripheral device.
US ^ n m 1F 5E n m
00 (n, m) ff n=Word time m=show string time
Set starting/ending position of macro definition.
Ex.: 1F 3A …………. ( macro string ) ..…. 1F 3A
Execute and quit macro.
It’s an interval of n between the two word.
It’s an interval of m between the two string.
Execute self - test
Display time
US @
US T h m
US U
ESC s 1
ESC d 1
1F 40
1F 54 h m
0<=h<=17h,
0<=m<=3bh
1F 55
1B 73 01
1B 64 01
Display time continuously
Store define download character to EEPROM
Restore user define character from EEPROM
Set international font for ESC/POS (Table 7-11) nternational font set
.S.A nternational font set
PAIN
RANCE
GERMANY
.K.
DENMARK I
WEDEN
TALY
0
1
2
5
APAN
ORWAY
DENMARK II
LAVONIC
RUSSIA
Reserved
Select code for ESC/POS (Table 7-12) nternational font set (80H~FFH) age 0, (PC437: U.S.A., standard Europe) age 1, (Katakana for Japan) age 2, (PC850: multilingual) age 3, (PC860: Portuguese) age 4, (PC863: Canadian-French) age 5, (PC865: Nordic) age 6, (SLAVONIC) age 7, (RUSSLA)
22
8. Character Set
8.1 International Character Sets
8.2 USA, Standard Character Sets (20H – 7EH)
23
8.3 Page 0 (PC437: USA, Standard Europe) (80H – FFH)
8.4 Page 1 (Katakana) (80H – FFH)
8.5 Page 2 (PC850: Mulitlingual) (80H – FFH)
24
8.6 Page 3 (PC860: Portuguese) (80H – FFH)
8.7 Page 4 (PC863: Canadian-French) (80H – FFH)
25
8.8 Page 5 (PC865: Nordic) (80H – FFH)
8.9 Page 6 (Slavonic) (80H – FFH)
26
8.10 Page 7 (Russia) (80H – FFH)
27
9.Command details
9.1 Overwrite mode
In this mode, the cursor will move rightward and begin from the upper left-end position. When the cursor reached the end of the upper line, the cursor will move down to the bottom left-end position to continue. When the cursor reached the end of the bottom line, it will move up the upper left-end position and overwrite the previous characters.
9.2 Vertical scroll mode
In this mode, the cursor will move rightward. The cursor will begin from the upper left-end position until it reached the end of the upper line, the cursor will then move down to the bottom left-end position to continue until it reached the end of the bottom line.
9.3 Horizontal scroll mode
In this mode, the extend of the cursor activity is bond by predefined range, limited to the upper line.(Please refer to Set or cancel window command), where the default window is the whole upper line. The cursor will begin from the left-end of the range and move rightward until it reached the end of the range, to continue, the characters that comes thereafter will start pushing the previous characters leftward from the right-end, scrolling the characters to the left.
9.4 Set the string display mode, and write string to display
Set the string display mode, write to upper or lower line d1 d2 d3 ….. dn {1 n 20} ‘A’ stands for the upper line, ‘B’ stands for the lower line, The string display mode will be cancelled and back to last mode after receive CLR or CAN
9.5 Upper line message scroll continuously
The message (previously defined) will scroll continuously in the horizontal direction until a new command is received.9.6 Move cursor left When the current cursor is at the left-end position, this command operates differently depends on the display mode. Overwrite mode: When the cursor reached the left-end of the lower line , it will continue to the right-end of the upper line, overwrite previous characters.
When it reached the left end of the upper line, it will continue to the right-end of the lower line.
Vertical scroll mode: When the cursor reached the left-end of the lower line, the lower line will scroll up and replace the previous upper line, the lower line will be cleared and the cursor will continue to the right end of the lower line. Horizontal scroll mode: The cursor will remain stationary.
9.7 Move cursor right
Move the cursor to the right. When the cursor reached the right-end, this command operates differently depending on the display mode. Overwrite mode: When the cursor reached the right-end of the lower line, it will continue to the left-end of the upper line, overwrite previous characters. When it reached the right-end of the upper line, it will continue to the right-end of the lower line. Vertical scroll mode: When the cursor reached the right-end of the lower line, the lower line will scroll up to replace the upper line, the lower line is cleared and ready to continue characters there after. Horizontal scroll mode: The cursor will remain stationary.
28
9.8 Move cursor up
Move the cursor up one line. When the or is on the upper line, this command operates differently depending on the display mode.
Overwrite mode: The cursor is moved to the same column the lower line.
Vertical scroll mode: The characters display on the upper line is scrolled to the lower line, and the upper line is cleared. The cursor will remain at the same position.
Horizontal scroll mode: The cursor will remain stationary.
9.9 Move cursor down
Move the cursor down one line. When the cursor reached the lower line, this command operates differently depending on the display mode.
Overwrite mode: The cursor is moved to the same column on the upper line.
Vertical scroll The characters display on the lower line are scrolled to the upper line, and the lower line is cleared.
The cursor will remain at the same position.
Horizontal scroll mode: The cursor will remain stationary.
9.10 Move cursor to home position
The cursor will move to the left-end position of the upper line
9.11 Move cursor to left-most position
The cursor will be moved to the left-end position of the current line.
9.12 Move cursor to right-most position
The cursor will be moved to the right-end position of the current line.
9.13 Move cursor to bottom position
The cursor will be moved to the right-end position on the lower line.
9.14 Move cursor to specified position
The cursor will be moved to the x column on the y line.
9.15 Initialize display
The data in the input buffer will be cleared and reset from default.
9.16 Reset the window
Reset the window on the display. When s=0, window is cancelled (values: x1, x2, and y are not required.)
When s=1 the window will be reset (values: x1, x2, and y are required.) The x1 and x2 set the position of the left column and right column, respectively, of the window. The y sets the upper line or the lower line of the window.
This function is valid within the horizontal mode.
29
9.17 Clear display screen, and clear string mode
All the display characters will be cleared, and the string mode will be cancelled.
9.18 Clear current line, and cancel string mode
The current line is cleared, and the string mode is cancelled.
9.19 Brightness adjustment
Adjust the brightness of the vacuum fluorescent display.
When n=3,brightness=70%
When n=4,brightness=100%
9.20 Set cursor ON or OFF
When n=0, cursor is OFF
When n=1, cursor is ON
9.21 Set user-defined characters
The n defines the beginning character code, and m defines the ending character code. When only one character is defined, use n=m
The ‘a’ denotes the number of dots in the horizontal direction. When a<5, the dot pattern for ‘ a’ on the right side of the
user-defined characters are padded with spaces p1 .. pa, the dot data is to defined the characters. This indicates the dot pattern for /a/ in the horizontal direction from the left side.
9.22 Reset user defined character set
When n=1, user-defined characters are selected. When the user-defined characters are not defined by the ESC & command, the internal character set will be displayed.
When n=0, user-defined characters are cancelled and the international character set is selected.
9.23 Cancel user defined characters
User-defined characters are cancelled.
This command cancels the defined characters specified by n.
If specified code is transmitted after the pattern is cancelled, the international character will be displayed.
9.24 Store the user defined character into EEPROM
If EEPROM is not supported, this command is ignored.
9.25 Restore the user defined character from EEPROM
If EEPROM is not supported, this command is ignored.
30
9.26 Character font format
One font consists of 5 bytes’ string. The string format is: it yte 1 yte 2 yte 3 yte 4 yte 5
R7C1
R7C2
R7C3
R7C4
R7C5
R6C1
R6C2
R6C3
R6C4
R6C5
R5C1
R5C2
R5C3
R5C4
R5C5
R4C1
R4C2
R4C3
R4C4
R4C5
R3C1
R3C2
R3C3
R3C4
R3C5
R2C1
R2C2
R2C3
R2C4
R2C5
R1C1
R1C2
R1C3
R1C4
R1C5
10. Control code set
09H HT 19H EM
0AH LF 1AH SUB
0DH CR 1DH GS
31
Appendix A: Display Module Dimension
200mm
176mm
0.38o
158.6mm
0.85mm
1.05mm
0.25mm
5.25mm
0.25mm
9.0mm
9.5mm
1.5mm
22.5mm
1.5mm
1.5mm
6.65mm
32
Descarcă
Link public actualizat
Linkul public către chat-ul tău a fost actualizat. You may view and manage your chat links after registration here.
Link public document
Publicitate
