SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 1

COLOR CCD CAMERA

INSTRUCTION MANUAL

SDC-313 SERIES

SDC-243 SERIES

About this manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.

SALES NETWORK

•

SAMSUNG TECHWIN CO., LTD.

Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,

Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-121

TEL : 82-31-740-8137~41 FAX: 82-31-740-8145

•

SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)

Samsung House, 1000 Hillswood Drive Hillswood Business

Park Chertsey Surrey KT16 OPS

TEL : 44-(0)1932-45-5308 FAX: 44-(0)1932-45-5325

• www.samsungcctv.com

•

SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)

Closed Circuit Division 40 Seaview Drive, Secaucus N.J 07094,

U.S.A

TEL : (201) 902-0347 FAX: (201) 902-0429

•

TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD (TSOE)

7 Pingchang Rd, Nankai Dist, Tianjin, P.R China Post

Code : 300190

TEL : 86-22-2761-9698 FAX: 86-22-2761-6514

P/No. : 6806-0415-01A

Printed in Korea

SAMSUNG CCD CAMERA

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 3

Thank you for purchasing a

SAMSUNG CCD CAMERA.

Before operating the camera, confirm the camera model and proper input power voltage. In order that you can understand this manual thoroughly, we'll introduce our model description.

SDC-313 Series (410,000 pixels)

• NTSC models

SDC- 313ND

SDC- 313NA

SDC-243 Series (270,000 pixels)

• NTSC models

SDC- 243ND

SDC- 243NA

Model Description

SDC- 313 x x

SDC- 243 x x

Power Source

Signal System

• Signal System

N NTSC Model

P PAL Model

• Power Source

D DC 12V

A AC 24V ~

• PAL models

SDC- 313PD

SDC- 313PA

• PAL models

SDC- 243PD

SDC- 243PA

WARNING- TO PREVENT ELECTRIC SHOCK AND RISK OF FIRE HAZARDS,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

INFORMATION -

This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING -

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

CAUTION -

To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 4

Features

High Resolution

The horizontal resolution of 480 TV lines can be achieved by using a high density

CCD having effective 410,000 pixels, which provides clean, noiseless and reliable pictures. (SDC-243 series have 270,000 pixel and can achieve 330 TV lines)

Video/DC Selection Switch

The camera accepts 2 types of auto lris lenses (DC type/Video type) and is set with

Video / DC selection switch.

Electronic Iris

Electronic iris shutter is automatically controlled at the speed of

1/60~1/120,000sec (NTSC models), 1/50~1/120,000sec (PAL models).

Excellent Backlight Compensation

The backlight compensation technology allows the camera to find the best picture conditions in any environment and automatically gives a necessary light level compensation, so that you can always obtain the clear picture, the finest detail and perfect light contrast.

SYNC. System

You can select INT (Internal Synchronization) mode or L. L (Linelock

Synchronization) mode.

COLOR CCD CAMERA

4

User’s Manual

P

recautions

C

omposition

N

ame and Function of Each Part

Front

Back

Bottom

C

onnection

Installing Auto IRIS Lens

Installing C-Mount Lens

Installing CS-Mount Lens

Connecting To Monitor

Connecting To Power

T

roubleshooting

S

pecification

Contents

6

8

9

9

10

14

15

15

17

17

18

18

20

22

COLOR CCD CAMERA

5

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 6

Precautions

Do not install the camera in extreme temperature conditions.

Do not install or use the camera in an environment where the humidity is high.

Do not drop the camera or subject them to physical shocks.

Never keep the camera face to strong light directly.

Only use the camera under conditions where temperatures are between -10˚C and +50˚C. Be especially careful to provide ventilation when operating under high temperatures.

It can cause the image quality to be poor.

Do not install the camera under unstable lighting conditions.

Do not touch the front lens of the camera.

It can cause malfunctions to occur.

Do not expose the camera to rain or spill beverage on it.

It can damage the CCD.

Severe lighting change or flicker can cause the camera to work improperly.

It is one of the most important parts of the camera. Be careful not to be stained by fingerprint.

COLOR CCD CAMERA

6

User’s Manual

If it gets wet, wipe it dry immediately.

Liquids can contain minerals that corrode the electronic components.

Notes

• If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur.

• Please check that the power satisfies the normal specification before connecting the camera.

COLOR CCD CAMERA

7

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 8

Composition

1. Color CCD Camera SDC-313(243)

2. Auto Iris Lens Plug

3. L-Wrench

4. Instruction Manual

5. C-Mount Adaptor

COLOR CCD CAMERA

8

User’s Manual

Front

Name and Function of Each Part

Glass Protecting Cap

Be sure to cap the lens mount when the lens is not mounted. Pull out the cap to remove.

C- Mount Lens Adaptor

Used to attach a C - mount lens.

CS-Mount Lens Adaptor

Used to attach a CS - mount lens. C-mount lens can be used when the C- mount adaptor is attached, and CS- mount lens can be used when it is removed.

CS-Mount Holding Screw

Used to readjust back focus of the camera. There are two back focus lock screws. These must be loosened before the camera may be back focused.

Loosen the lock screws using the

L- wrench

to turn the CS-mount lens adaptor, and tighten the lock screws after adjustment.

COLOR CCD CAMERA

9

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 10

Name and Function of Each Part

Back

* This diagram is based on SDC-313(243)NA/PA

Video Out Jack

Connect to the video input connector of monitor. This jack outputs a composite video signal. Use a coaxial cable for connection.

Auto lris Lens Connector

Used to connect auto iris lens plug.

Auto IRIS Lens Selection Switch

Used to choose DC or VIDEO mode according to the type of your lens.

• Using Auto Iris Lens

You can choose DC or VIDEO mode according to the type of the lens. ln this case, electronic shutter is fixed in ‘1/60’sec (NTSC models), ‘1/50’sec (PAL models).

Notes

• Using auto iris lens, you must select ‘OFF’ of the ESC selection switch.

COLOR CCD CAMERA

10

User’s Manual

• Using Manual Lens

Using manual lens, you can choose any switch selection. When the switch is set to ‘OFF’ in ESC mode, the electronic shutter is fixed in ‘1/60’sec (NTSC models), ‘1/50’sec(PAL models). When the switch is set to ‘ON’ in ESC mode, the electronic shutter automatically controls the shutter speed from ‘1/60’ to

‘1/120,000’sec (NTSC models), ‘1/50’ to ‘1/120,000’sec (PAL models).

DC Level Adjustment V.R

Used to adjust video output level of DC driven auto iris lens. When the brightness control of the monitor does not operate correctly, you can get the optimum picture by controlling the DC level of camera.

Monitor Picture Adjustment direction

To make it brighter Turn clockwise

Monitor Picture Adjustment direction

To make it darker Turn counterclockwise

Notes

• You must select ‘OFF’ of the ESC selection switch if you want to adjust DC level adjustment V. R.

V. PHASE Adjustment V.R: AC type

If the camera is to be used in the LL mode, the vertical phase may require adjustment to synchronize the vertical phase of the camera with other camera in the system. Make this adjustment when the vertical phase of the camera does not match with other cameras or systems. For correct adjustment, use a multi - channel oscilloscope. The V. PHASE adjustment can be readjusted in the range of 0 to 270 degrees.

Notes

• This adjustment is necessary only when linelock is performed.

• There is no V. PHASE adjustment VR on the rear of DC power type.

COLOR CCD CAMERA

11

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 12

Name and Function of Each Part

Power Lamp

The power lamp turns on when power is properly supplied.

Power Input Terminal

Used to connect AC/DC power source.

Function Selection Switch

* Use the select switches on the rear of camera.

Notes

• Default setting is subject to change without notice.

• If the camera is DC power type, you can not use LL mode.

(1) ESC ON/OFF Switch

You can activate the ESC(Electronic Shutter Control) function. For details, refer to

‘Auto IRIS Lens Selection Switch.’

Notes

• Using auto iris lens, you must select ‘OFF’ of the ESC ON/OFF switch.

(2) BLC(Backlight Compensation) ON/OFF Switch

This switch improves an image that is darkened because of backlighting. When the lighting source is in the rear of an object, the object might be seen somewhat dark. If you want to see the object clearly, turn this switch ON. The effective area where backlight compensation is activate is fixed in the center of the screen.

(3) White Balance Control Mode

• ATW(Auto Tracing White balance; ON): The camera automatically controls the white balance in any environment.

COLOR CCD CAMERA

12

User’s Manual

• AWC(Auto White balance Control; OFF): The white balance is automatically adjusted in a specific environment.

(4) Sharpness

The switch emphasize the sharpness. To soften the edge turn this switch off.

(5) Flickerless: SDC-313 Series

Flickerless function. In this function, electronic shutter is fixed in 1/100sec

(1/120sec: PAL model). FL function can compensate the flicker caused by power frequency, but set OFF in the area not using a 60Hz (50Hz: PAL model) AC Power.

(6) INT/LL Switch: AC type

Used to choose INT or LL mode.

• INT(Internal) mode : The camera may be operated independently with its internal crystal control.

• LL(Linelock) mode : It synchronizes the video signal between cameras using the frequency of the AC power supply without external synchronous generator.

Notes

• The LL mode can be used in the areas of 60Hz(NTSC models), 50Hz(PAL models).

• There is no SYNC mode selection switch on the rear of DC power type.

• In case of NTSC model in using manual lens, the color tone could be oscillated under indoor fluorescent light.

• To avoid this situation, we kindly recommend auto iris lens to you and set to ‘OFF’ in

ESC mode.

COLOR CCD CAMERA

13

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 14

Name and Function of Each Part

Bottom

Tripod Mounting Hole

Used to install the camera on an optional tripod.

The tripod must be equipped with the screw specified as shown below.

L

1/4"-20 UNC (20 THREAD)

L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard)

You can remove and install this bracket on the top of the camera. You must use the supplied screw or the equivalent (within 5mm). If not, the bracket may not be fixed properly.

COLOR CCD CAMERA

14

User’s Manual

Connection

LENS

The lens is not supplied with this camera. Purchase a lens suitable for your environment. This camera accepts the auto iris lens and both C-and CS-mount lens.

Notes

• If the lens is marked with fingerprints or other marks, the image quality might be poor.

• It is recommended to use a high quality lens to improve the image quality under low illumination.

• For using main functions it is recommended to use Auto Iris Lens with DC type.

Installing Auto Iris Lens

1. Peel approximately 8mm from the end of the lens cable outer cover.

approx. 8mm

2. Peel approximately 2mm from the end of the cable inner cover.

approx. 2mm

COLOR CCD CAMERA

15

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 16

Connection

3. Remove the cover from the iris lens plug supplied, and solder the lens cable to the plug as shown below.

• Video type :

No. 1 Pin --- Red (Power source)

No. 2 Pin --- N.C

No. 3 Pin --- White (Video signal)

No. 4 Pin --- Black (GND)

• DC type :

No. 1 Pin --- Damping -

No. 2 Pin --- Damping +

No. 3 Pin --- Drive +

No. 4 Pin --- Drive -

Lens cable

No. 3 Pin

No. 1 Pin connector

No. 4 Pin

No. 2 Pin

4. Remove the protective cap, and attach the lens to the camera by turning clockwise.

5. Connect the lens plug to the auto iris connector on the right side of the camera.

6. Set the DC/VIDEO selection switch to DC or VIDEO according to the type of the lens.

COLOR CCD CAMERA

16

User’s Manual

Installing C-Mount Lens

After removing the protecting cap, attach the lens into the camera by turning clockwise.

C-mount lens adaptor

Installing CS-Mount Lens

1. Remove the protecting cap and C- mount adaptor.

C-mount lens adaptor

Protecting cap

2. Attach the lens into the camera by turning clockwise.

CS-mount lens adaptor

Notes

• Use the lens under the specification as shown. Otherwise the lens can damage the camera or abnormal fixing may result.

• A heavy lens may disturb the balance with the camera and possibly result in damage. Don't use a lens heavier than

450g.

• It is recommended to set the lens ALC mode to Av mode

(Average). Pk mode can be occurred hunting.

C-mount lens : 10mm or less

CS-mount lens : 5 mm or less

COLOR CCD CAMERA

17

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 18

Connection

Connecting to Monitor

Connect the VIDEO out jack to the monitor video in jack.

CCD Camera Monitor

• As the connecting method varies with the instruments, refer to the manual supplied with the instrument.

• Connect the cable after power is turned off.

• Set the 75 Ω / Hi-Z selection switch as shown below if you have an intermediate device.

CCD Camera

Intermediate End monitor

Connecting to Power

Each model has different power specification, please check the name of the model and power specification before connecting to power source.

Please refer to the sticker identifying the model, which is attached on the product, for power specification.

COLOR CCD CAMERA

18

User’s Manual

For DC Power Type

• The wire is polarized. Be sure to connect the wire that white line is on covering to ‘-’ terminal and connect the other one to ‘+’ terminal.

• Use DC 12V power source for SDC-

313(243)ND / PD

For AC Power Type

• The wire is non-polarized.

• Use AC 24V ~ 60Hz power source for

SDC-313(243)NA.

• Use AC 24V~50Hz power source for

SDC-313(243)PA

Notes

• Be sure to connect power after all the installation is done.

• Note that AC adaptor is not supplied with camera.

• Use only AC 24V UL listed class 2 power supply.

• Since the wire of DC power type is polarized, be careful when connecting it.

• Do not use power sources other than that specified.

COLOR CCD CAMERA

19

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 20

Troubleshooting

If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician.

Solution Problem

Nothing appears on the screen.

The image on the screen is dim.

The image on the screen is dark.

The camera is not working properly, and the surface of the camera is hot.

• Check that the power cord and line connection between the camera and monitor are fixed properly.

• Check that you have properly connected VIDEO cable to the camera VIDEO output jack.

• Check that the DC/VIDEO selection switch on the side of the camera is set to a proper position according to the type of your auto iris lens.

• Are you using Auto Iris Lens with VIDEO type?

Adjust VR Level properly (refer to page 10)

• Is lens stained with dirt? Clean your lens with soft, clean cloth.

• Set the monitor to proper condition.

• If the camera is exposed to too strong light, change the camera position.

• Adjust the lens’ focus properly.

• Adjust the contrast feature of the monitor.

• If you have an intermediate device, set the 75 Ω / Hi-z properly. (refer to page 18)

• Are you using the Auto Iris Lens? Adjust the level on the lens properly.

• Check that you have properly connected the camera to an appropriate power source. (refer to page 19)

Problem

The image on the screen flickers.

L/L mode isn’t able to be selected.

Solution

• Is the camera facing to direct sunlight or fluoresent lighting? Change the camera position.

• Are you using Auto Iris Lens? Check that you have properly connected the lens plug to the Auto Iris connector on the side of the camera.

• Have you connected your camera to DC power source? Connect it to AC power source.

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 22

Specifications

Item

Power Source

Power Consumption

Synchronization

Image Pick-up Device

Total Pixels

Effective Pixels

Scanning

Min. Illumination

Resolution

Video Output

Scanning Frequency

Electronic Shutter (ESC)

AGC

White Balance

BLC Function

Sharpness

Flickerless

Auto Iris

Lens Mount

S/N Ratio

Operating Temperature

Dimention

Weight (Without Lens)

* Design and specifications are subject to change without notice

SDC-243NA SDC-243ND

AC 24V, 60Hz

3.5W (Max)

DC 12V

2.5W (Max)

SDC-313NA SDC-313ND

AC 24V, 60Hz

3.5W (Max)

DC 12V

2.5W (Max)

INT/LL Selectable

(0~270˚ Adjustable)

INT

INT/LL Selectable

(0~270˚ Adjustable)

INT

1/3” Color Interline-Transfer CCD

542(H) x 492(V) 816(H) x 494(V)

512(H) x 492(V) 771(H) x 492(V)

2:1 Interlace

0.3Lux / F1.0 0.5Lux / F1.0

330 TV Line 480 TV Line

VBS ; 1Vp-p, 75 Ω unbalaced

15.734KHz(H) / 60Hz (V)

ON / OFF Selectable (ON: 1/60~120,000sec, OFF: 1/60sec)

Built in

ATW / AWC Selectable

ON / OFF Selectable

Not used

High / Normal Selectable

ON / OFF Selectable (ON: 1/100)

VIDEO / DC Iris Selectable (DC Iris Level Adjustable)

300g

C / CS Mount more than 48dB (weight ON)

-10˚C ~ +50˚C / 30% ~ 90%RH

58(W) x 52(H) x 121(D)mm

280g 300g 280g

COLOR CCD CAMERA

22

User’s Manual

Item

Power Source

Power Consumption

Synchronization

Image Pick-up Device

Total Pixels

Effective Pixels

Scanning

Min. Illumination

Resolution

Video Output

Scanning Frequency

Electronic Shutter (ESC)

AGC

White Balance

BLC Function

Sharpness

Flickerless

Auto Iris

Lens Mount

S/N Ratio

Operating Temperature

Dimention

Weight (Without Lens)

* Design and specifications are subject to change without notice

SDC-243PA

AC 24V, 50Hz

3.5W (Max)

SDC-243PD

DC 12V

2.5W (Max)

SDC-313PA

AC 24V, 50Hz

3.5W (Max)

SDC-313PD

DC 12V

2.5W (Max)

INT/LL Selectable

(0~270˚ Adjustable)

INT

INT/LL Selectable

(0~270˚ Adjustable)

INT

1/3” Color Interline-Transfer CCD

542(H) x 582(V) 798(H) x 584(V)

512(H) x 582(V) 753(H) x 582(V)

2:1 Interlace

0.3Lux / F1.0 0.5Lux / F1.0

330 TV Line 480 TV Line

VBS ; 1Vp-p, 75 Ω unbalaced

15.625KHz(H) / 50Hz (V)

ON / OFF Selectable (ON: 1/50~120,000sec, OFF: 1/50sec)

Built in

ATW / AWC Selectable

ON / OFF Selectable

High / Normal Selectable

Not used ON / OFF Selectable (ON: 1/120sec)

VIDEO / DC Iris Selectable (DC Iris Level Adjustable)

300g

C / CS Mount more than 48dB (weight ON)

-10˚C ~ +50˚C / 30% ~ 90%RH

58(W) x 52(H) x 121(D)mm

280g 300g 280g

COLOR CCD CAMERA

23

User’s Manual

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 24

DECLARATION OF CONFORMITY

Application of Council Directive(s) 89 / 336 / EEC

Manufacturer's Name SAMSUNG TECHWIN CO., LTD

Manufacturer's Address SAMSUNG TECHWIN CO., LTD

42, SUNGJU-DONG CHANGWON-CITY,

KYUNGNAM, KOREA, 641-120

European Representative Name

European Representative Address

Equipment Type/Environment

Model Name

Beginning Serial NO.

Year of Manufacture

Conformance to

CCTV Camera

SDC-313PA / PD, SDC-243PA / PD

S3600001

2003. 6. 1

EN 50081-1 : 1992

EMC-Directive 89/336 EEC and 92/31/EEC

EN 50130-4 : 1996

We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).

Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe

Signature Signature

Full Name

Position

YOUNG TAEK SON

QUALITY CONTROL MANAGER

Full Name

Position

Place

Date 2003. 6. 1 Date

MEMO

SDC-313,243( 영 ) 2003.6.26 5:1 PM 페이지 26

MEMO MEMO