ABIT KU8 AMD Athlon™ 64 System Board motherboard User’s Manual

KU8
AMD Athlon™ 64 System Board
Socket 754
User’s Manual
4200-0444-01
Rev. 1.00
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are the
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
If you do not properly set the motherboard settings, causing the motherboard to
malfunction or fail, we cannot guarantee any responsibility.
KU8
Table of Contents
Chapter 1.
1-1.
1-2.
Chapter 2.
2-1.
2-2.
2-3.
2-4.
Hardware Setup.................................................................... 2-1
Install The Motherboard...........................................................................2-1
Install CPU, Heatsink and Fan Assembly................................................2-2
Install System Memory ............................................................................2-4
Connectors, Headers and Switches ..........................................................2-5
(1). ATX Power Input Connectors ........................................................2-5
(2). FAN Power Connectors .................................................................2-6
(3). CMOS Memory Clearing Header ..................................................2-7
(4). Front Panel Switches & Indicators Headers ..................................2-8
(5). Additional USB Port Headers ........................................................2-9
(6). Wake-up Header...........................................................................2-10
(7). Front Panel Audio Connection Header ........................................2-11
(8). Internal Audio Connectors ...........................................................2-12
(9). Accelerated Graphics Port Slot ....................................................2-13
(10). Floppy and IDE Disk Drive Connectors ......................................2-14
(11). Serial ATA Connectors .................................................................2-15
(12). Status Indicators...........................................................................2-16
(13). Back Panel Connectors ................................................................2-17
Chapter 3.
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
Introduction .......................................................................... 1-1
Features & Specifications ........................................................................1-1
Layout Diagram .......................................................................................1-3
BIOS Setup............................................................................ 3-1
SoftMenu Setup........................................................................................3-2
Standard CMOS Features.........................................................................3-4
Advanced BIOS Features.........................................................................3-7
Advanced Chipset Features......................................................................3-9
Integrated Peripherals ............................................................................3-15
Power Management Setup .....................................................................3-19
PnP/PCI Configurations.........................................................................3-21
PC Health Status ....................................................................................3-23
Load Fail-Safe Defaults .........................................................................3-25
Load Optimized Defaults .......................................................................3-25
User’s Manual
3-11.
3-12.
3-13.
Set Password ..........................................................................................3-25
Save & Exit Setup ..................................................................................3-25
Exit Without Saving...............................................................................3-25
Appendix A.
Install ULi M1689 single chipset .................................................... A-1
Appendix B.
Install Audio Driver ......................................................................... B-1
Appendix C.
Install LAN Driver ........................................................................... C-1
Appendix D.
Install ULi M5289 SATA Driver .....................................................D-1
Appendix E.
Install Cool 'n' Quiet Driver............................................................ E-1
Appendix F.
ABIT EQ (The Hardware Doctor Utility) ....................................... F-1
Appendix G.
Troubleshooting (Need Assistance?)...............................................G-1
Appendix H.
How to Get Technical Support ........................................................H-1
KU8
Introduction
1-1
Chapter 1. Introduction
1-1. Features & Specifications
1. CPU
•
Supports AMD Socket 754 Athlon 64/Sempron Processor with 1.6GHz system bus using
Hyper Transport™ Technology
•
Supports AMD CPU Cool ‘n’ Quiet Technology
2. Chipset
•
ULI M1689 single chip
3. Memory
•
•
•
Two 184-pin DIMM sockets
Supports DDR400 non-ECC un-buffered memory
Supports maximum memory capacity up to 2GB
4. ABIT Engineered
•
•
ABIT SoftMenu™ Technology
ABIT CPU ThermalGuard™ Technology
5. SATA 150
•
Serial ATA 1.5Gbps data transfer rate
6. LAN
•
Onboard 10/100M LAN Controller
7. Audio
•
Onboard 6-Channel AC 97 CODEC
8. Internal I/O Connectors
•
•
•
•
•
1x AGP 8X/4X slot
5x PCI slots
1x Floppy port supports up to 2.88MB
2x Ultra DMA 133/100/66/33 IDE connectors
2x SATA 150 connectors
•
•
2x USB headers
1x CD-IN header
9. Back Panel I/O
•
•
•
•
1x PS/2 keyboard, 1x PS/2 mouse
1x Parallel Port, 1x Serial Port
1x AUDIO1 connector (Mic-In, Line-In, Front-Left/Front-Right)
4x USB Connectors
User’s Manual
1-2
Chapter 1
•
1x RJ-45 LAN Connector
10. Miscellaneous
•
!
KU8
ATX form factor: 305 x 225 mm
Specifications and information contained herein are subject to change without notice.
Introduction
1-3
1-2. Layout Diagram
User’s Manual
1-4
KU8
Chapter 1
Hardware Setup
2-1
Chapter 2. Hardware Setup
Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or
disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do
so may cause the motherboard components or add-on cards to malfunction or damaged.
2-1. Install The Motherboard
Most computer chassis have a base with many mounting holes to allow motherboard to be securely
attached on and at the same time, prevented from short circuits. There are two ways to attach the
motherboard to the chassis base:
1. use with studs
2. or use with spacers
In principle, the best way to attach the board is to
use with studs. Only if you are unable to do this
should you attach the board with spacers. Line up
the holes on the board with the mounting holes on
the chassis. If the holes line up and there are
screw holes, you can attach the board with studs.
If the holes line up and there are only slots, you
can only attach with spacers. Take the tip of the
spacers and insert them into the slots. After doing
this to all the slots, you can slide the board into
position aligned with slots. After the board has been positioned, check to make sure everything is OK
before putting the chassis back on.
ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they
are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
User’s Manual
2-2
Chapter 2
2-2. Install CPU, Heatsink and Fan Assembly
Please pay attention to the following notices
before installing the CPU and heatsink/fan
assembly.
1. Always use the processor with the
Heatsink and Fan Assembly installed.
2. Do not touch the pins on the processor.
3. If you ever need to reinstall the Heatsink
and fan Assembly, please clean the
heatsink surface and apply new thermal
interface material first.
3. Lower the locking lever to the fully locked
position.
1. Pull out the socket locking lever slightly,
then lift it up.
4.
2. Align the corner with triangle mark of the
processor with the marking on the motherboard,
and then place the processor vertical down into
the socket.
KU8
Apply thermal interface material.
5. Place the heatsink and fan assembly onto
the retention frame. Match the heatsink clip
with the socket mounting lug. Hook the spring
clip to the mounting lug.
Hardware Setup
2-3
6. On the other side, push the retention clip
straight down to lock into the plastic lug on the
retention frame.
7. Turn the cam lever to lock into the retention
frame.
8. Attach the four-pin power plug from the
heatsink and fan assembly to the CPU FAN
connector.
For detailed information on how to install your
heatsink and fan assembly, please refer to the
instruction manual came packed with the
heatsink and fan assembly you bought.
User’s Manual
2-4
Chapter 2
2-3. Install System Memory
This system board provides two 184-pin DDR DIMM slots for DDR 400 memory modules with memory
expansion size up to 2GB.
Bank
Memory Module
Total Memory
Bank 0, 1 (DIMM1)
256MB, 512MB, 1GB
256MB ~ 1GB
256MB, 512MB, 1GB
256MB ~ 1GB
Bank 2, 3 (DIMM2)
Total System Memory
256MB ~ 2GB
NOTE: Usually there is no hardware or BIOS setup require after adding or removing memory modules,
but you will have to clear the CMOS memory first if any memory module related problem occurs.
Power off the computer and unplug the AC power cord before installing or removing memory modules.
1.
Locate the DIMM slot on the board.
2.
Hold two edges of the DIMM module
carefully, keep away of touching its
connectors.
3.
Align the notch key on the module with the
rib on the slot.
4.
Firmly press the module into the slots until
the ejector tabs at both sides of the slot
automatically snaps into the mounting notch.
Do not force the DIMM module in with extra force as the DIMM module only fit in one direction.
5.
To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and
then pull out the DIMM module.
ATTENTION: Static electricity can damage the electronic components of the computer or optional
boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a
grounded metal object briefly.
KU8
Hardware Setup
2-5
2-4. Connectors, Headers and Switches
Here we will show you all of the connectors, headers and switches, and how to connect them. Please read
the entire section for necessary information before attempting to finish all the hardware installation inside
the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of
connectors and headers on the board that you may refer to.
WARNING: Always power off the computer and unplug the AC power cord before adding or removing
any peripheral or component. Failing to so may cause severe damage to your motherboard and/or
peripherals. Plug in the AC power cord only after you have carefully checked everything.
(1). ATX Power Input Connectors
This motherboard provides two power connectors to connect ATX12V power supplier.
NOTE: This 24-pin power connector “ATXPWR1” is compliant to the former 20-pin type. Pay attention
to the orientation when doing so (Pin-11, 12, 23, and 24 should be left un-connected).
User’s Manual
2-6
Chapter 2
(2). FAN Power Connectors
These connectors each provide power to the cooling fans installed in your system.
•
CPUFAN1: CPU Fan Power Connector
•
SYSFAN1: System Fan Power Connector
•
AUXFAN1: Auxiliary Fan Power Connector
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.
KU8
Hardware Setup
2-7
(3). CMOS Memory Clearing Header
This header uses a jumper cap to clear the CMOS memory.
•
Pin 1-2 shorted (default): Normal operation.
•
Pin 2-3 shorted: Clear CMOS memory.
WARNING: Turn the power off first (including the +5V standby power) before clearing the CMOS
memory. Failing to do so may cause your system to work abnormally or malfunction.
User’s Manual
2-8
Chapter 2
(4). Front Panel Switches & Indicators Headers
This header is used for connecting switches and LED indicators on the chassis front panel.
Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection. Please pay attention to connect these headers. A
wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could
cause system malfunction.
•
HLED (Pin 1, 3):
Connects to the HDD LED cable of chassis front panel.
•
RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis front panel.
•
SPKR (Pin 13, 15, 17, 19):
Connects to the System Speaker cable of chassis.
•
SLED (Pin 2, 4):
Connects to the Suspend LED cable (if there is one) of chassis front panel.
•
PWR (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
•
PLED (Pin 16, 18, 20):
Connects to the Power LED cable of chassis front panel.
KU8
Hardware Setup
2-9
(5). Additional USB Port Headers
These headers each provide 2 additional USB 2.0 ports connection through an USB cable designed for
USB 2.0 specifications.
Pin
Pin Assignment
Pin
Pin Assignment
1
VCC
2
VCC
3
Data0 -
4
Data1 -
5
Data0 +
6
Data1 +
7
Ground
8
Ground
9
NC
10
NC
User’s Manual
2-10
Chapter 2
(6). Wake-up Header
These headers use a jumper cap to enable/disable the wake-up function.
•
PS2-PWR1:
Pin 1-2 shorted (default): Disable wake-up function support at Keyboard/Mouse port.
Pin 2-3 shorted: Enable wake-up function support at Keyboard/Mouse port.
•
USBPWR1:
Pin 1-2 shorted: Disable wake-up function support at USB1 port.
Pin 2-3 shorted (default): Enable wake-up function support at USB1 port.
•
USBPWR2:
Pin 1-2 shorted: Disable wake-up function support at USB2 port.
Pin 2-3 shorted (default): Enable wake-up function support at USB2 port.
KU8
Hardware Setup
2-11
(7). Front Panel Audio Connection Header
This header provides the connection to audio connector at front panel.
•
To use the audio connector at front panel, remove all the jumpers on this header, and then connect
to front panel by the extension cable provided with the chassis.
•
To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at
pin 5-6, and pin 9-10 (default setting).
Pin
1
3
5
7
9
Pin Assignment
Audio Mic.
Audio Mic. Bias
Speaker Out Right
Channel
X
Speaker Out Left
Channel
Pin
2
4
6
8
10
Pin Assignment
Ground
VCC
Speaker Out Right
Channel Return
NC
Speaker Out Left
Channel Return
User’s Manual
2-12
(8). Internal Audio Connectors
This connector connects to the audio output of internal CD-ROM drive or add-on card.
KU8
Chapter 2
Hardware Setup
2-13
(9). Accelerated Graphics Port Slot
This slot supports an optional AGP graphics card up to AGP 8X mode.
ATTENTION: This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards.
User’s Manual
2-14
Chapter 2
(10). Floppy and IDE Disk Drive Connectors
The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable. Connect
the single end at the longer length of ribbon cable to the FDC1 on the board, the two connectors on the
other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your
system.
NOTE: The red line on the ribbon cable must be aligned with pin-1 on both the FDC1 port and the floppy
connector.
Each of the IDE port connects up to two IDE drives at
Ultra ATA/100 mode by one 40-pin, 80-conductor, and
3-connector Ultra ATA/66 ribbon cables.
Connect the single end (blue connector) at the longer
length of ribbon cable to the IDE port of this board, the
other two ends (gray and black connector) at the shorter
length of the ribbon cable to the connectors of your hard
drives.
NOTE: Make sure to configure the “Master” and “Slave” relation before connecting two drives by one
single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and
the hard-drive connector.
KU8
Hardware Setup
2-15
(11). Serial ATA Connectors
These connectors are provided to attach one Serial ATA device at each channel via Serial ATA cable.
User’s Manual
2-16
Chapter 2
(12). Status Indicators
• LED2 (5VSB): This LED lights up when the power supply is connected with power source.
KU8
Hardware Setup
2-17
(13). Back Panel Connectors
• Mouse: Connects to PS/2 mouse.
• Keyboard: Connects to PS/2 keyboard.
• LPT1: Connects to printer or other devices that support this communication protocol.
• COM1: Connects to external modem, mouse or other devices that support this communication
protocol.
• AUDIO1:
Mic In: Connects to the plug from external microphone.
Line In: Connects to the line out from external audio sources.
F.L./F.R. (Front Left / Front Right): Connects to the front left and front right channel in the
5.1-channel or regular 2-channel audio system.
• LAN: Connects to Local Area Network.
• USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse,
keyboard, hub, digital camera, joystick etc.
User’s Manual
2-18
KU8
Chapter 2
BIOS Setup
3-1
Chapter 3. BIOS Setup
This motherboard provides a programmable EEPROM that you can update the BIOS utility. The BIOS
(Basic Input/Output System) is a program that deals with the basic level of communication between
processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring
system, or prompted to “Run Setup”. This chapter explains the Setup Utility of BIOS utility.
After powering up the system, the BIOS message appears on the screen, the memory count begins, and
then the following message appears on the screen:
PRESS DEL TO ENTER SETUP
If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del>
keys, or by pressing the Reset button on computer chassis. Only when it failed by these two methods can
you restart the system by powering it off and then back on.
After pressing <Del> key, the main menu screen appears.
Phoenix – AwardBIOS CMOS Setup Utility
► SoftMenu Setup
► PC Health Status
► Standard CMOS Features
Load Fail-Safe Defaults
► Advanced BIOS Features
Load Optimized Defaults
► Advanced Chipset Features
Set Password
► Integrated Peripherals
Save & Exit Setup
► Power Management Setup
Exit Without Saving
► PnP/PCI Configurations
Esc : Quit
F10 : Save & Exit Setup
↑ ↓ → ← : Select Item
(M1609-W03627-6A7K4A19C-00)
Change CPU’s Clock & Voltage
NOTE: In order to increase system stability and performance, our engineering staffs are constantly
improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for
your reference only, may not completely match what you see on your screen.
In the BIOS Setup main menu, you can see several options. We will explain these options step by step in
the following pages of this chapter, but let us first see a short description of the function keys you may
use here.
Esc:
Press this button to quit the BIOS Setup.
↑↓← →:
Press these buttons to choose, in the main menu, the option you want to confirm or to modify.
F10:
When you have completed the setup of BIOS parameters, press this button to save these parameters and
to exit the BIOS Setup menu.
User’s Manual
3-2
Chapter 3
3-1. SoftMenu Setup
The SoftMenu utility is ABIT’s exclusive and ultimate solution in programming the CPU operating speed.
All the parameters regarding CPU FSB speed, multiplier factor, the AGP & PCI clock, and even the CPU
core voltage are all available at your fingertips.
Phoenix – AwardBIOS CMOS Setup Utility
SoftMenu Setup
Brand Name : AMD Sempron(tm) Processor 3100+
Item Help
Frequency
: 1810MHz
CPU Operating Speed
X - Multiplier Factor
X - CPU FSB Clock(MHz)
X - AGP Clock
Default
StarUp
204
AUTO
Voltages Control
X - CPU Core Voltage
X - DDR Voltage
- DDR Ref Voltage
- AGP Voltage
X - Chipset Voltage
Default
+0mV
2.60 V
-2.5%
1.50 V
Default
Spread Spectrum
Spread 2%
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Brand Name:
This item displays the CPU model name.
Frequency:
This item displays the CPU internal clock speed.
CPU Operating Speed:
This item displays the CPU operating speed according to the type and speed of your CPU. You can also
select the [User Define] option to enter the manual option.
User Define:
WARNING: The wrong settings of the multiplier and external clock in certain circumstances may cause
CPU damage. Setting the working frequency higher than the PCI chipset or processor specs, may cause
abnormal memory module functioning, system hangs, hard disk drive data lose, abnormal functioning of
the VGA card, or abnormal functioning with other add-on cards. Using non-specification settings for your
CPU is not the intention of this explanation. These should be used for engineering testing, not for normal
applications.
There will be no guaranty for the settings beyond specification, any damage of any component on this
motherboard or peripherals result therein is not our responsibility.
KU8
BIOS Setup
!
3-3
Multiplier Factor:
This item displays the multiplier factor for the CPU you installed.
!
CPU FSB Clock(MHz):
This item selects the external clock frequency. Due to the specification limit of the CPU you installed, the
speed you set over its standard bus speed is supported, but not guaranteed.
!
AGP Clock(MHz):
This item allows you to set the AGP clock speed from 66MHz to 75MHz. Due to the AGP specification
limit, the speed you set over its standard clock speed is supported, but not guaranteed.
Voltage Control:
This option allows you to switch between the default and user-defined voltages. Leave this setting to
default unless the current voltage setting cannot be detected or is not correct. The option “User Define”
enables you to select the following voltages manually.
!
CPU Core Voltage:
This item selects the CPU core voltage.
!
DDR Voltage:
This item selects the voltage for DRAM slot.
!
DDR Ref Voltage:
This item selects the reference voltage needed for DRAM slot to increase its conformity.
!
AGP Voltage:
This item selects the voltage for AGP slot.
!
Chipset Voltage:
This item selects the Chipset voltage.
ATTENTION: A wrong voltage setting may cause the system unstable or even damage the CPU. Please
leave it to default settings unless you are fully aware of its consequences.
Spread Spectrum:
For EMC (Electro-Magnetic Compatibility) testing, you may need to adjust these options for optimal
results. We do not recommend you change the default, except for special reasons. Some values you select
may cause system instability under some situations. Please be careful.
User’s Manual
3-4
Chapter 3
3-2. Standard CMOS Features
This section contains the basic configuration parameters of the BIOS. These parameters include date,
hour, VGA card, FDD and HDD settings.
Phoenix – AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Sat. Jan 1 2005
Item Help
Time (hh:mm:ss)
0 : 6 : 56
►
►
►
►
IDE
IDE
IDE
IDE
Channel
Channel
Channel
Channel
0
0
1
1
Master
Slave
Master
Slave
Drive A
Floppy 3 Mode Support
Halt On
Base Memory
Extended Memory
Total Memory
None
None
None
None
1.44M, 3.5 in.
Disabled
[All, But keyboard]
640K
523264K
524288K
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Date (mm:dd:yy):
This item sets the date you specify (usually the current date) in the format of [Month], [Date], and [Year].
Time (hh:mm:ss):
This item sets the time you specify (usually the current time) in the format of [Hour], [Minute], and
[Second].
KU8
BIOS Setup
#
3-5
IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave:
Click <Enter> key to enter its submenu:
Phoenix – AwardBIOS CMOS Setup Utility
IDE Primary Master
IDE HDD Auto-Detection
Press Enter
IDE Channel 0 Master
Access Mode
Auto
Auto
Capacity
0 MB
Cylinder
Head
Precomp
Landing Zone
Sector
0
0
0
0
0
Item Help
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
IDE HDD Auto-Detection:
This item allows you to detect the parameters of IDE drives by pressing <Enter> key. The parameters will
be shown on the screen automatically.
IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave:
When set to [Auto], the BIOS will automatically check what kind of IDE drive you are using. If you want
to define your own drive by yourself, set it to [Manual] and make sure you fully understand the meaning
of the parameters. Please refer to the instruction manual provided by the device’s manufacturer to get the
setting right.
Access Mode:
This item selects the mode to access your IDE devices. Leave this item to its default [Auto] setting to
detect the access mode of your HDD automatically.
Capacity:
This item displays the approximate capacity of the disk drive. Usually the size is slightly greater than the
size of a formatted disk given by a disk-checking program.
Cylinder:
This item configures the numbers of cylinders.
Head:
This item configures the numbers of read/write heads.
User’s Manual
3-6
Chapter 3
Precomp:
This item displays the number of cylinders at which to change the write timing.
Landing Zone:
This item displays the number of cylinders specified as the landing zone for the read/write heads.
Sector:
This item configures the numbers of sectors per track.
#
Back to Standard CMOS Features Setup Menu:
Drive A:
This item sets the type of floppy drives (usually only Drive A) installed.
Floppy 3 Mode Support:
This item allows you to use “3 Mode Floppy Drive” in Japanese computer system by selecting drive A, B,
or both. Leave this item to its default [Disabled] setting if you are not using this Japanese standard floppy
drive.
Halt On:
This item determines whether the system stops if an error is detected during system boot-up.
[All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error.
[No Errors]: The system-boot will not stop for any error detected.
[All, But Keyboard]: The system-boot will stop for all errors except a keyboard error.
[All, But Diskette]: The system-boot will stop for all errors except a diskette error.
[All, But Disk/Key]: The system-boot will stop for all errors except a diskette or keyboard error.
Base Memory:
This item displays the amount of base memory installed in the system. The value of the base memory is
typically 640K for system with 640K or more memory size installed on the motherboard.
Extended Memory:
This item displays the amount of extended memory detected during system boot-up.
Total Memory:
This item displays the total memory available in the system.
KU8
BIOS Setup
3-7
3-3. Advanced BIOS Features
Phoenix – AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Quick Power on Self Test
Enabled
► Hard Disk Boot Priority
Press Enter
First Boot Device
Floppy
Second Boot Device
Hard Disk
Third Boot Device
CDROM
Boot Other Device
Enabled
Boot Up Floppy Seek
Disabled
Boot Up NumLock Status
On
Security Option
Setup
MPS Version Ctrl For OS
1.4
Report No FDD for OS
No
Delay IDE Initial(Seconds)
0
Full Screen LOGO Show
Enabled
Item Help
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Quick Power On Self Test:
When set to [Enabled], this item speeds up the Power On Self Test (POST) after powering on the system.
The BIOS shorten or skip some check during the POST.
Hard Disk Boot Priority:
This item selects the hard disks booting priority. By pressing <Enter> key, you can enter its submenu
where the hard disks detected can be selected for the booting sequence to boot up system.
This item functions only when there is the option of [Hard Disk] in any one of the First/Second/Third
Boot Device items.
First Boot Device / Second Boot Device / Third Boot Device / Boot Other Device:
Select the drive to boot first, second and third in the [First Boot Device], [Second Boot Device], and
[Third Boot Device] items respectively. The BIOS will boot the operating system according to the
sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another
device other than these three items.
Boot Up Floppy Seek:
When the computer boots up, the BIOS detects if the system has a FDD or not. When this item is set to
Enabled, if the BIOS detects no floppy drive, it will display a floppy disk drive error message. If this item
is disabled, the BIOS will skip this test. The default setting is Disabled.
User’s Manual
3-8
Chapter 3
Boot Up NumLock Status:
This item determines the default state of the numeric keypad at system booting up.
[On]: The numeric keypad functions as number keys.
[Off]: The numeric keypad functions as arrow keys.
Security Option:
This item determines when the system will prompt for password - every time the system boots or only
when enters the BIOS setup.
[Setup]: The password is required only when accessing the BIOS Setup.
[System]: The password is required each time the computer boots up.
To disable security, select Set Password at main menu and then you will be asked to enter the password.
Do not type anything and just press the <Enter> key and it will disable security. Once security is disabled,
the system will boot and you can enter the BIOS setup menu freely.
NOTE: Don’t forget your password. If you forget the password, you will have to open the computer case
and clear all information in the CMOS before you can start up the system. But by doing this, you will
have to reset all previously set options.
MPS Version Ctrl For OS:
This item specifies which version of MPS (Multi-Processor Specification) this motherboard will use.
Leave this item to its default setting.
Report No FDD For OS:
When set to [Enabled], this item allows you to run some older operating system without floppy disk drive.
Leave this item to its default setting.
Delay IDE Initial(Seconds):
This item allows the BIOS to support some old or special IDE devices by prolonging this delay time. A
larger value will give more delay time to the device for which to initialize and to prepare for activation.
Full Screen LOGO Show:
This item determines to show the full screen logo when booting.
KU8
BIOS Setup
3-9
3-4. Advanced Chipset Features
►
►
►
►
Phoenix – Award WorkstationBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Configuration
Press Enter
Item Help
M1689 Configuration
Press Enter
AGP Configuration
Press Enter
HyperTransport Config
Press Enter
ALI HPET
Disabled
Init Display First
PCI Slot
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
#
DRAM Configuration:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
DRAM Configuration
DRAM Timing Selectable
Auto
Item Help
X - DRAM Clock
Auto
X - CAS latency Time
Auto
X - Row Cycle Time
Auto
X - Row Refresh Cycle Time
Auto
X - RAS# to CAS# delay
Auto
X - RAS# to RAS# delay
Auto
X - Min RAS# Active time
Auto
X - RAS# Precharge Time
Auto
X - Write Recovery Time
Auto
X - Write to Read Delay
Auto
X - Read to Write Delay
Auto
X - DRAM Command rate
Auto
X - Burst Length
4 beats
X - Bank Interleaving
Enabled
32 bit Dram Memory Hole
Auto
MTRR mapping mode
Continuous
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
DRAM Timing Selectable:
This item selects the DRAM timing mode. When set to “By SPD”, the BIOS will read the DRAM module
SPD data and automatically set to the values stored in it. Leave this item to its default “Auto” setting.
!
DRAM Clock:
This item sets the DRAM clock of your DRAM module. The system may be unstable or unable to boot up
if your DRAM module does not support the clock you set.
User’s Manual
3-10
Chapter 3
When set to [By SPD], the BIOS will read the DRAM module SPD data and automatically set the DRAM
clock by the value stored in it.
!
CAS Latency Time:
Three options are available: 2 $ 2.5 $ 3. The default setting is 2.5. You can select SDRAM CAS
(Column Address Strobe) latency time according your SDRAM specification.
!
Row Cycle Time:
This item specifies the RAS# active to RAS# active time or auto refresh time of the same bank.
!
Row Refresh Cycle Time:
This item specifies the auto refresh active to RAS# active time or RAS# auto refresh time.
!
RAS# to CAS# Delay:
This item specifies the RAS# active to CAS# read write delay time to the same bank.
!
RAS# to RAS# Delay:
This item specifies the RAS# active to RAS# active delay time of different bank.
!
Min. RAS# Active Time:
This item specifies the minimum RAS# active time.
!
RAS# Precharge Time:
This item specifies the RAS# precharge time.
!
Write Recovery Time:
This item specifies the time measured from the last write datum is safely registered by the DRAM.
!
Write to Read Delay:
This item specifies the time measured from the rising edge following the last non-masked data strobe to
the rising edge of the next read command.
!
Read to Write Delay:
This item specifies the read to write delay.
!
DRAM Command Rate:
Two options are available: 2T Command or 1T Command. The default setting is 2T Command. When the
host (northbridge) locates the desired memory address, it then processes the wait state of commands.
!
Burst Length
DDR SDRAM modules provide a Burst mode that means an auto precharge function for programmable
READ or WRITE burst lengths of 4 or 8 locations.
This means that if we set burst length to 8, the address bus will access 8 bytes each cycle to precharge,
etc.
!
Bank Interleaving:
Three options are available: Disabled $ 2 Way $ 4 Way. The default setting is Disabled. Depending on
your SDRAM module structure, the 4-Way setting can offer the best performance. If you choose the
wrong setting, the computer system will not run in a stable manner. For detailed information on your
SDRAM module, please ask your SDRAM module manufacturer.
KU8
BIOS Setup
3-11
32 bit Dram Memory Hole:
This item selects the method to remap the 32 bit Dram memory hole. Leave this item to its default “Auto”
Setting.
MTRR mapping mode
The item selects the MTRR mapping mode. The MTRR (Memory-Type and Range Registers) controls
the access and cacheability of memory regions in the processor.
User’s Manual
3-12
#
Chapter 3
M1689 Configuration:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
M1689 Configuration
M1689 Gated Clock
Disabled
Item Help
PCI/14M/USB CLK PowerDown
Disabled
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
M1689 Gated Clock:
This item enables or disables the M1689 Gated Clock.
PCI/14H/USB CLK Powerdown:
This item enables or disables the PCI/14H/USB Clock Powerdown.
KU8
BIOS Setup
#
3-13
AGP Configuration:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
AGP Configuration
AGP 3.0 Transfer Mode
1x/2x/4x/8x
Item Help
Fast Write
Enabled
AGP Aperture Size (MB)
256
AGP Secondary Lat Timer
20h
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
AGP 3.0 Transfer Mode:
This item selects the data transfer rate of AGP device. A higher rate delivers faster and better graphics to
your system. Make sure your graphics card supports the mode you select.
Fast Write:
Two options are available: Disabled $ Enabled. The default setting is Disabled. If your AGP adapter can
support this function, then you can choose Enabled. Otherwise, choose Disabled.
AGP Aperture Size (MB):
This option specifies the amount of system memory that can be used by the AGP device. The aperture is a
portion of the PCI memory address range dedicated for graphics memory address space.
AGP Secondary Lat Timer:
This item selects the value for AGP Secondary Latency Timer.
User’s Manual
3-14
#
Chapter 3
HyperTransport Config:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
HyperTransport Config
Hammer to M1689 Freq.
800Mhz
Item Help
Hammer to M1689 Width
16bits/8 bits
M1689 HTT Tristate
Disabled
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Hammer to M1689 Freq.:
This item selects the LDT Bus Frequency.
Hammer to M1689 Width:
This item selects the LDT Bus Width.
M1689 HTT Tristate:
This item enables or disables the M1689 HTT Tristate.
#
Back to Advanced Chipset Features Setup Menu:
ALI HPET:
This item enables or disables the ALI HPET (High Precision Event Timer).
Init Display First:
This item selects to initialize AGP or PCI Slot first when the system boots.
[PCI Slot]: When the system boots, it will first initialize PCI.
[AGP]: When the system boots, it will first initialize AGP.
KU8
BIOS Setup
3-15
3-5. Integrated Peripherals
►
►
►
►
Phoenix – AwardBIOS CMOS Setup Utility
Integrated Peripherals
OnChip IDE Device
Press Enter
OnChip PCI Device
Press Enter
SuperIO Device
Press Enter
Onboard PCI Device
Press Enter
Item Help
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
#
OnChip IDE Device:
Click <Enter> key to enter its submenu:
Phoenix – AwardBIOS CMOS Setup Utility
OnChip IDE Device
IDE Bus Master
Enabled
OnChip IDE-1 Controller
Enabled
OnChip IDE-2 Controller
Enabled
OnChip SATA
Enabled
- OnChip SATA Mode
IDE
Item Help
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
IDE Bus Master:
This option enables or disables the IDE bus mastering capability under the DOS environment.
User’s Manual
3-16
Chapter 3
OnChip IDE-1 Controller/OnChip IDE-2 Controller:
This item allows you to enable or disable the primary and secondary IDE controller. Select [Disabled] if
you want to add a different hard drive controller.
OnCip SATA:
This item enables or disables the on-chip SATA controller.
!
OnChip SATA Mode:
This item determines the mode for on-chip Serial ATA.
[IDE]: The on-chip Serial ATA served as IDE mode.
[RAID]: The on-chip Serial ATA served as RAID mode.
#
OnChip PCI Device:
Click <Enter> key to enter its submenu:
Phoenix – AwardBIOS CMOS Setup Utility
OnChip PCI Device
OnChip USB Controller
Enabled
- USB 2.0 Controller
Enabled
X - USB Keyboard Support Via
OS
X - USB Mouse Support Via
OS
OnChip Audio Controller
Enabled
Item Help
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
OnChip USB Controller:
This option enables or disables the USB controller. If you choose to disable this item, the “USB
Keyboard Support Via” and “USB Mouse Support Via” items will not be able to select in Integrated
Peripherals menu.
!
USB 2.0 Controller:
This option enables or disables the USB 2.0 controller.
!
USB Keyboard Support Via:
This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS
environment.
KU8
BIOS Setup
!
3-17
USB Mouse Support Via:
This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS
environment.
OnChip Audio Controller:
This option enables or disables the audio controller.
#
Super IO Device:
Click <Enter> key to enter its submenu:
Phoenix – AwardBIOS CMOS Setup Utility
SuperIO Device
Onboard FDC Controller
Enabled
Onboard Serial Port 1
3F8/IRQ4
Onboard Parallel Port
378/IRQ7
Parallel Port Mode
SPP
X - EPP Mode Select
EPP1.7
X - ECP Mode Use DMA
3
Item Help
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Onboard FDC Controller:
Two options are available: Enabled and Disabled. The default setting is Enabled. You can enable or
disable the onboard FDC controller.
Onboard Serial Port 1:
This is used to specify the I/O address and IRQ of Serial Port 1. Six options are available: Disabled $
3F8/IRQ4 $ 2F8/IRQ3 $ 3E8/IRQ4 $ 2E8/IRQ3 $ AUTO. The default setting is 3F8/IRQ4.
Onboard Parallel Port:
Sets the I/O address and IRQ of the onboard parallel port. Four options are available: Disabled $
378/IRQ7 $ 278/IRQ5 $ 3BC/IRQ7. Default setting is 378/IRQ7.
Parallel Port Mode:
Four options are available: SPP $ EPP $ ECP $ ECP+EPP. The default setting is SPP mode.
!
EPP Mode Select:
Two options are available: EPP1.7 $ EPP1.9. The default setting is EPP 1.7 When the mode selected for
the parallel port mode is EPP, the two EPP version options are available.
User’s Manual
3-18
!
Chapter 3
ECP Mode Use DMA:
Two options are available: 1 $ 3. The default setting is 3. When the mode selected for the parallel port
mode is ECP, the DMA channel selected can be Channel 1 or Channel 3.
#
Onboard PCI Device:
Click <Enter> key to enter its submenu:
Phoenix – AwardBIOS CMOS Setup Utility
Onboard PCI Device
Onboard LAN Controller
Enabled
- LAN Boot ROM
Disabled
Item Help
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Onboard LAN Controller:
This option enables or disables the LAN controller.
!
LAN Boot ROM:
This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the
local area network directly.
KU8
BIOS Setup
3-19
3-6. Power Management Setup
X
X
X
X
Phoenix – Award WorkstationBIOS CMOS Setup Utility
Power Management Setup
ACPI Suspend Type
S3(Suspend-to-RAM)
Item Help
- Resume by USB from S3
Enabled
Power Button Function
Instant-Off
Wake-Up by PME# of PCI
Enabled
Resume by Ring
Disabled
Wakeup by Alarm
Disabled
- Date(of Month) Alarm
0
- Time (hh:mm:ss) Alarm
0 : 0 : 0
Cool’n’Quiet Technology
Enabled
POWER ON Function
BUTTON ONLY
- KB Power ON Password
Enter
- Hot Key Power ON
Ctrl-F1
Restore on AC Power Loss
Off
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
ACPI Suspend Type:
This item selects the type of Suspend mode.
[S1(PowerOn-Suspend)]: Enables the Power On Suspend function.
[S3(Suspend-To-RAM)]: Enables the Suspend to RAM function.
!
Resume by USB from S3:
Two options are available: Disabled or Enabled. The default setting is Enabled. When set to Enabled, any
event affecting from onchip USB will awaken a system that has powered down. This item can be
configured only if the item “ACPI Suspend Type” is set to [S3(STR)].
Power Button Function:
Two options are available: Delay 4 Sec or Instant-Off. The default setting is Instant-Off. It is activated
when the user presses the power button for more than four seconds while the system is in the working
state, then the system will transition to the soft-off (Power off by software). This is called the power
button over-ride.
Wake-up by PME# of PCI:
Two options are available: Disabled or Enabled. The default setting is Enabled. When set to Enabled, any
event affecting from PCI card (PME) will awaken a system that has powered down.
Resume by Ring:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
any event affecting from Modem Ring will awaken a system that has powered down.
User’s Manual
3-20
Chapter 3
Wakeup by Alarm:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
you can set the date and time at which the RTC (real-time clock) alarm awakens the system from Suspend
mode.
!
Day (of Month) Alarm/ Time (hh:mm:ss) Alarm:
You can set the Date (month) Alarm and Time Alarm (hh:mm:ss). Any event occurring will awaken a
system that has powered down.
Cool ’n’ Quiet Technology:
This option enables or disables the AMD K8 cool and quiet function.
Power On Function:
This item selects the way you want your system to power on.
[Password]: Use a password to power on the system, select this option then press <Enter>. Enter your
password. You can enter up to 5 characters. Type in exactly the same password to confirm, and then press
<Enter>.
[Hot KEY]: Use any of the function keys between <F1> to <F12> to power on the system.
[Mouse Left]: Double click the mouse left button to power on the system.
[Mouse Right]: Double click the mouse right button to power on the system.
[Any KEY]: Use any keyboard keys to power on the system.
[BUTTON ONLY]: Use only the power button to power on the system.
[Keyboard 98]: Use the power-on button on the “Keyboard 98” compatible keyboard to power on the
system.
!
KB Power On Password:
When you perss the <Enter> key, then you can enter the password you want. When set be done, you need
to saving and leave the BIOS setting menu to reboot your computer system. Next time when you
shutdown your computer, you can’t use the power button to turn on the computer power anymore.
You need to press the password to turn on your computer power.
!
Hot Key Power On:
Fifteen options are available: Ctrl+F1 ~ Ctrl+F12, Power, Wake and Any Key. The default setting is
Ctrl+F1. You can choose the hot key that you want it to turn on your computer power.
Restore on AC Power Loss:
This item selects the system action after an AC power failure.
[Off]: When power returns after an AC power failure, the system’s power remains off. You must press
the Power button to power-on the system.
[On]: When power returns after an AC power failure, the system’s power will be powered on
automatically.
[Former-Sts]: When power returns after an AC power failure, the system will return to the state where
you left off before power failure occurs. If the system’s power is off when AC power failure occurs, it
will remain off when power returns. If the system’s power is on when AC power failure occurs, the
system will power-on when power returns.
KU8
BIOS Setup
3-21
3-7. PnP/PCI Configurations
Phoenix – Award WorkstationBIOS CMOS Setup Utility
PnP/PCI Configurations
Resources Controlled By
Auto(ESCD)
Item Help
x IRQ Resources
Press Enter
PCI/VGA Pallete Snoop
PIRQ_1 Use IRQ No.
PIRQ_2 Use IRQ No.
PIRQ_3 Use IRQ No.
PIRQ_4 Use IRQ No.
PIRQ_5 Use IRQ No.
PIRQ_6 Use IRQ No.
PIRQ_7 Use IRQ No.
PIRQ_8 Use IRQ No.
Disbaled
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Resources Controlled By:
This item configures all of the boot and Plug-and-Play compatible devices.
[Auto(ESCD)]: The system will automatically detect the settings.
[Manual]: Choose the specific IRQ resources in the “IRQ Resources” menu.
#
IRQ Resources:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
IRQ Resources
IRQ-3 assigned to
PCI Device
IRQ-4 assigned to
PCI Device
IRQ-7 assigned to
PCI Device
IRQ-10 assigned to
PCI Device
IRQ-11 assigned to
PCI Device
IRQ-12 assigned to
PCI Device
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
This item sets each system interrupt to either [PCI Device] or [Reserved].
User’s Manual
3-22
#
Chapter 3
Back to PnP/PCI Configurations Setup Menu:
PCI/VGA Palette Snoop:
This item determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA or not.
[Disabled]: MPEG ISA/VESA VGA cards do not work with PCI/VGA.
[Enabled]: MPEG ISA/VESA VGA cards work with PCI/VGA.
PIRQ 1 Use IRQ No. ~ PIRQ 8 Use IRQ No.:
This item specifies the IRQ number manually or automatically for the devices installed on PCI slots.
KU8
BIOS Setup
3-23
3-8. PC Health Status
You can set the warning temperature for your computer system, and you can check the fan speeds and
power supply voltages of your computer system. The features are useful for monitoring all the important
parameters within your computer system. We call it the PC Health Status.
Phoenix – AwardBIOS CMOS Setup Utility
PC Health Status
Shutdown Temperature
95OC/203OF
Item Help
CPU Warning Temperature
80OC/176OF
FAN Fail Alarm Selectable
Disabled
CPU FANEQ Control
Enabled
- FanEQ Target Temperature
55OC/131OF
- FanEQ Temp. Tolerance
5OC/41OF
- FanEQ Start Control
70%
- FanEQ Stop Control
30%
CPU Temperature
42OC/107OF
System Temperature
30OC/100OF
PWM Temperature
42OC/107OF
SYS FAN Speed
0 RPM
CPU FAN Speed
2000 RPM
AUX FAN Speed
O RPM
CPU Core Voltage
1.42 V
DDR Voltage
2.68 V
DDR VTT Voltage
1.33 V
AGP VDDQ Voltage
1.52 V
ATX +12V
11.96 V
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Shutdown Temperature:
You can set the processor shutdown temperature here. If the processor temperature exceeds the settings
value, system will force to shutdown to protect the processor not overheat.
CPU Warning Temperature:
This item lets you select the temperature at which you want the system to send out a warning message to
the PC speakers of when the temperature goes beyond either limit. You can select the temperatures you
want.
FAN Fail Alarm Selectable:
This item selects the fan that will be monitored for malfunction.
CPU FANEQ Control:
This item allows you to control the CPU fan speed. When set to [enabled], the following items become
selectable.
!
FanEQ Target Temperature:
This item allows you to set a wanted temperature for the CPU.
!
FanEQ Temp. Tolerance:
This item sets the high/low limits of the target temperature.
User’s Manual
3-24
!
Chapter 3
FanEQ Start Control:
This item sets a specific speed for the fan when it is turned on. The fan will be turned on once the CPU
temperature exceeds the high limit temperature set by the above 2 items.
!
FanEQ Stop Control:
This item sets a minimum speed for the fan. The fan will be running at this speed when the CPU
temperature is below the low limit temperature.
All Voltages, Fans Speed and Thermal Monitoring:
These unchangeable items list the current status of the CPU and environment temperatures, fan speeds,
and system power voltage.
NOTE: The hardware monitoring features for temperatures, fans and voltages will occupy the I/O
address from 294H to 297H. If you have a network adapter, sound card or other add-on cards that might
use those I/O addresses, please adjust your add-on card I/O address to avoid using these addresses.
KU8
BIOS Setup
3-25
3-9. Load Fail-Safe Defaults
This option loads the BIOS default values for the most stable, minimal-performance system operations.
3-10. Load Optimized Defaults
This option loads the BIOS default values that are factory settings for optimal-performance system
operations.
3-11. Set Password
This option protects the BIOS configuration or restricts access to the computer itself.
3-12. Save & Exit Setup
This option saves your selections and exits the BIOS setup menu.
3-13. Exit Without Saving
This option exits the BIOS setup menu without saving any change.
User’s Manual
3-26
KU8
Chapter 3
Install ULi M1689 single chipset
A-1
Appendix A. Install ULi M1689 single chipset
NOTE: Please install this ULi M1689 single chipset driver first after having installed the Windows
operating system.
The installation procedures and screen shots in
this section are based on the Windows XP
operating system. For other operating systems,
please follow the on-screen instructions.
Insert the Driver & Utility CD into the
CD-ROM drive. It should execute the
installation program automatically. If not,
double-click the executable file at the main
directory of this CD to enter the installation
menu.
3.
Click [Ok].
After entering the installation menu, move your
curser to [Drivers] tab. Click [ULi M1689
single chipset]. The following screen appears.
4. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
1.
Click [Next].
2.
Click [Next].
User’s Manual
A-2
KU8
Appendix A
Install Audio Driver
B-1
Appendix B. Install Audio Driver
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [Audio Driver].
The following screen appears.
1.
Click [Next].
2. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
User’s Manual
B-2
KU8
Appendix B
Install LAN Driver
C-1
Appendix C. Install LAN Driver
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [LAN Driver]. The
following screen appears.
1.
Click [OK].
User’s Manual
C-2
KU8
Appendix C
Install ULi M5289 SATA Driver
D-1
Appendix D. Install ULi M5289 SATA Driver
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [ULi M5289
SATA Driver]. The following screen appears.
1.
Click [Next].
2. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
User’s Manual
D-2
KU8
Appendix D
Install Cool 'n' Quiet Driver
E-1
Appendix E. Install Cool 'n' Quiet Driver
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [Cool 'n' Quiet
Driver]. The following screen appears.
1.
2.
3.
Click [Next].
4.
Click [Next].
Click [Next].
Click [Yes].
5. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
User’s Manual
E-2
6. After the system restarted, open the “Power
Options” from the control panel and choose the
power scheme “Minimal Power Management”
to enable Cool ‘n’ Quiet.
NOTE: For Windows 2000 or ME system, an
AMD Cool ‘n’ Quiet tab will appear under
“Power Options” when the Cool ‘n’ Quiet
software for Windows 2000 and ME is installed.
This must be set to “Automatic Mode” for Cool
‘n’ Quiet to be enabled.
KU8
Appendix E
ABIT EQ (The Hardware Doctor Utility)
F-1
Appendix F. ABIT EQ (The Hardware Doctor Utility)
ABIT EQ is a self-diagnostic system for PC based on motherboards designed and manufactured by ABIT
Computer Corporation. It will protect PC Hardware by monitoring critical items of Power Supply Voltage,
CPU & System Fans Speed, and CPU & System Temperature.
The installation procedures and screen shots in
this section are based on the Windows XP
operating system. For other operating systems,
please follow the on-screen instructions.
Insert the Driver & Utility CD into the
CD-ROM drive. It should execute the
installation program automatically. If not,
double-click the executable file at the main
directory of this CD to enter the installation
menu.
After entering the installation menu, move your
curser to [ABIT Utility] tab. Click [ABIT EQ].
The following screen appears.
1.
Click [Next].
2.
Click [Next].
3. Choose [Yes, I want to restart my computer
now.] and click [Finish] to complete setup.
User’s Manual
F-2
4. Execute the ABIT EQ by entering the
Windows Menu [Start] $ [All Programs] $
[ABIT] $ [ABIT EQ].
5. This screen appears. ABIT EQ shows you
the status of Voltage, Fan Speed, and
Temperature readings as well.
KU8
Appendix F
Troubleshooting (Need Assistance?)
G-1
Appendix G. Troubleshooting (Need Assistance?)
Q & A:
Q: Do I need to clear the CMOS before I use a new motherboard to assemble my new computer
system?
A: Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please
move the CMOS jumper from its default 1-2 position to 2-3 for a few seconds, and then back. When
you boot up your system for the first time, follow the instructions in the user's manual to load the
optimized defaults.
Q: If my system hangs when I update the BIOS or set the wrong CPU parameters, what should I
do?
A: Whenever you update the BIOS or if the system hangs due to wrong CPU parameters setting, always
clear CMOS jumper before booting up again.
Q: Why does the system fail to boot up again right after a mechanical power-off?
A: Please keep a 30-second interval between each mechanical power On/Off.
Q: Why does the system fail to boot up and nothing displays on the screen after I did some
overclocking or non-standard settings inside the BIOS? Is the motherboard dead? Do I need to
return it to where I bought from or go through an RMA process?
A: It should not cause hardware or permanent damage to motherboard when BIOS settings were
changed from default to over-clocking or non-standard status.
We suggest the following three troubleshooting methods to discharge CMOS data, recover the
hardware default status, and then making the motherboard work again. There is no need to bother
returning the motherboard to where you bought it from or go through an RMA process.
Step 1. Switch off the power supply unit and then switch it on again after one minute. If there is no
power switch on the power supply unit, disconnect its power cord for one minute and then
reconnect.
Press and hold the <Insert> key on the keyboard, and press the power-on button to boot up
system. If it works, release the <Insert> key and hit <Del> key to enter the BIOS setup page
to apply the correct settings.
If the situation remains the same, repeat the procedures in Step 1 for three times, or try Step
2.
Step 2. Switch off the power supply unit or disconnect the power cord. Open the chassis cover.
Locate the CCMOS jumper near the button battery. Change the jumper position from default
1-2 to 2-3 for one minute to discharge the CMOS data, and then put it back to default 1-2
position.
Close the chassis and switch on the power supply unit or plug in the power cord. Press the
power-on button to boot up system. If it works, hit <Del> key to enter the BIOS setup page
to do the correct settings.
If the situation remains the same, try Step 3.
Step 3. The same procedure as Step 2, but while discharging the CMOS data, pull out the ATX
power connectors from motherboard and remove the button battery during CMOS discharge.
User’s Manual
G-2
Appendix G
Q: How can I get a quick response to my request for technical support?
A: Be sure to follow the guidelines as stated in the “Technical Support Form” section of this manual.
If you have a problem during operation, in order to help our technical support personnel quickly
determine the problem with your motherboard and give you the answers you need, eliminate any
peripheral that is not related to the problem, and indicate it on the form. Fax this form to your dealer
or to the company where you bought the hardware in order to receive prompt technical support. (You
can refer to the examples given below)
Example 1:
With a system including: motherboard (with CPU, DRAM...) HDD, CD-ROM, FDD, VGA CARD,
MPEG CARD, SCSI CARD, SOUND CARD, etc. If you cannot boot up after the system is
assembled, check the key components of the system using the procedure described below. First
remove all interface cards except the VGA card and try to reboot.
If you still cannot boot up: Try installing another brand/model VGA card and see if the system will
start. If it still does not start, note the VGA card model, motherboard model, Bios identification
number, and CPU on the technical support form (refer to main instructions), and describe the
problem in the space provided.
If you can boot up: Insert the interface cards you have removed back into the system one by one,
and try to start the system each time you insert a card until the system will not start. Keep the VGA
card and the interface card that caused the problem inserted on the motherboard, remove any other
cards or peripheral, and start again. If you still cannot start, note the information related to both cards
in the add-on Card space provided, and don’t forget to indicate the motherboard model, version,
BIOS identification number, CPU (refer to main instructions), and give a description of the problem.
Example 2:
With a system including the motherboard (with CPU, DRAM...) HDD, CD-ROM, FDD, VGA
CARD, LAN CARD, MPEG CARD, SCSI CARD, SOUND CARD, after assembly and after having
installed the sound card driver, when you restart the system, it resets automatically when it runs the
sound card Driver,. This problem may be due to the sound card driver. During the Starting DOS…
procedure, press SHIFT (BY-PASS) key, to skip CONFIG.SYS and AUTOEXEC.BAT; edit
CONFIG.SYS with a text editor, and in line that loads the sound card driver, add a remark REM, in
order to disable the sound card driver. See the example below.
CONFIG.SYS:
DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\EMM386.EXE HIGHSCAN
DOS=HIGH, UMB
FILES=40
BUFFERS=36
REM DEVICEHIGH=C:\PLUGPLAY\DWCFGMG.SYS
LASTDRIVE=Z
Restart the system. If the system starts and does not reset, you can be sure that the problem is due to
the sound card driver. Write down the sound card model, motherboard model, BIOS identification
number on the technical support file (refer to main instructions), and describe the problem in the
space provided.
We will show you how to fill the “Technical Support Form”.
KU8
Troubleshooting (Need Assistance?)
G-3
Main instructions:
To fill in this “Technical Support Form”, refer to the step-by-step instructions given below:
1*. MODEL: Note the model number given in your user’s manual.
Example: KU8
2*. Motherboard model number (REV): Note the motherboard model number labeled on the
motherboard as “REV:*.**”.
Example: REV: 1.00
*
3 . BIOS ID and Part Number: See the on screen message.
4.
DRIVER REV: Note the driver
version number indicated on the
DEVICE DRIVER disk (if any) as
“Release *.**”. For example:
5*. OS/APPLICATION: Indicate the
operating system and applications
you are running on the system.
Example: MS-DOS® 6.22,
Windows® 98 SE, Windows® 2000, etc....
6*. CPU: Indicate the brand and the speed (MHz) of your CPU.
Example:(A) In the “Brand” space, write “Intel”; in the “Specifications” space, write “Pentium® 4
1.9GHz”.
7.
HDD: Indicate the brand and specifications of your HDD(s); specify if the HDD is using %IDE1 or
%IDE2. If you know the disk capacity, indicate it and check (“&”) “ ”; in case you give no
indication, we will consider that your HDD is “'IDE1” Master.
Example: In the “HDD” space, check the box; in the Brand space, write “Seagate”; in the
Specifications space, write “ST31621A (1.6GB)”.
8.
CD-ROM Drive: Indicate the brand and specifications of your CD-ROM drive. Specify if it uses %
IDE1 or %IDE2， and check (“&”) “ ”; in case you give no indication, we will consider that your
CD-ROM is “'IDE2” Master.
Example: In the “CD-ROM drive” space, check the box, in the Brand space, write “Mitsumi”, in the
Specifications space, write “FX-400D”.
9.
System Memory (DDR SDRAM): Indicate the brand and specifications (DDR DIMM) of your
system memory. Such as Density, Description, Module Components, Module Part Number, CAS
Latency, and Speed (MHz).
For example: In the Brand space, write “Micron”; in the Specifications space, write: Density:
128MB, Description: SS 16 Megx72 2.5V ECC Gold, Module Components: (9) 16 Megx 8,
Module Part Number: MT9VDDT1672AG, CAS Latency: 2, Speed (MHz): 200 MHz.
Please give us the detailed information of your DDR SDRAM module; it will help us to simulate the
problems you met.
10. ADD-ON CARD: Indicate which add-on cards you are absolutely sure are related to the problem.
If you cannot identify the problem’s origin, indicate all the add-on cards inserted into your system.
NOTE: Items between the “*” are absolutely necessary.
User’s Manual
G-4
Appendix G
(
Technical Support Form
! Company Name:
) Phone Number:
" Contact Person:
# Fax Number:
* E-mail Address:
Model
*
Motherboard Model No.
DRIVER REV
OS/Application
*
Hardware Name
Brand
CPU
HDD
CD-ROM-Drive
System Memory
ADD-ON CARD
Problem Description:
KU8
*
IDE1
IDE2
IDE1
IDE2
BIOS ID #
Specifications
*
How to Get Technical Support
H-1
Appendix H. How to Get Technical Support
(From our website) http://www.abit.com.tw
(In North America) http://www.abit-usa.com
(In Europe) http://www.abit.nl
Thank you for choosing ABIT products. ABIT sells all our products through distributors,
resellers and system integrators; we have no direct sales to end-users. Before sending email
for tech support please check with your resellers or integrators if you need any services, they
are the ones who sold you your system and they should know best as to what can be done,
how they serve you is a good reference for future purchases.
We appreciate every customer and would like to provide the best service to you. Providing
fast service to our customers is our top priority. However we receive many phone calls and a
huge amount of email from all over the world. At the present time it is impossible for us to
respond to every single inquiry. Therefore it is quite possible that if you send an email to us
that you may not receive a response.
We have done many compatibility tests and reliability tests to make sure our products have
the best quality and compatibility. In case you need service or technical support, please
understand the constraint we have and always check with the reseller who sold the product
to you first.
To expedite service, we recommend that you follow the procedures outlined below before
contacting us. With your help, we can meet our commitment to provide the best service to the
greatest number of ABIT customers:
1. Check the Manual. It sounds simple but we have taken a lot of care in making a
well-written and thorough manual. It is full of information that doesn't only pertain to
motherboards. The CD-ROM included with your board will have the manual as well as
drivers. If you don't have either one, go to our Program Download Area of the Website or
FTP server.
2. Download latest BIOS, software or drivers. Please go to our Program Download area
on our Website to check to see if you have the latest BIOS. They are developed over
periods of time to fixes bugs or incompatibilities. Also please make sure you have the
latest drivers from your peripheral cards makers!
3. Check the ABIT Technical Terms Guide and FAQ on our Website. We are trying to
expand and make the FAQs more helpful and information rich. Let us know if you have
any suggestions. For hot topics, check out our HOT FAQ!
User’s Manual
H-2
Appendix H
4. Internet Newsgroups. They are a great source of information and many people there can
offer help. ABIT's Internet News group, alt.comp.periphs.mainboard.abit, is an ideal
forum for the public to exchange information and discuss experiences they have had with
ABIT products. Many times you will see that your question has already been asked before.
This is a public Internet news group and it is reserved for free discussions. Here is a list of
some of the more popular ones:
alt.comp.periphs.mainboard.abit
comp.sys.ibm.pc.hardware.chips
alt.comp.hardware.overclocking
alt.comp.hardware.homebuilt
alt.comp.hardware.pc-homebuilt
5. Ask your reseller. Your ABIT authorized distributor should be able to provide the fastest
solution to your technical problem. We sell our products through distributors who sell to
resellers and stores. Your reseller should be very familiar with your system configuration
and should be able to solve your problem much more efficiently than we could. After all,
your reseller regards you as an important customer who may purchase more products and
who can urge your friends to buy from him or her as well. They integrated and sold the
system to you. They should know best what your system configuration is and your
problem. They should have reasonable return or refund policies. How they serve you is
also a good reference for your next purchase.
6. Contacting ABIT. If you feel that you need to contact ABIT directly you can send email
to the ABIT technical support department. First, please contact the support team for the
branch office closest to you. They will be more familiar with local conditions and
problems and will have better insight as to which resellers offer what products and
services. Due to the huge number of emails coming in every day and other reasons, such
as the time required for problem reproduction, we will not be able to reply to every email.
Please understand that we are selling through distribution channels and don't have the
resources to serve every end-user. However, we will try to do our best to help every
customer. Please also remember that for many of our technical support team English is a
second language, you will have a better chance of getting a helpful answer if your
question can be understood in the first place. Be sure to use very, simple, concise
language that clearly states the problem, avoid rambling or flowery language and always
list your system components. Here is the contact information for our branch offices:
KU8
How to Get Technical Support
North America and
South America
H-3
ABIT Computer (U.S.A.) Corporation
45531 Northport Loop West,
Fremont CA, 94538, U.S.A.
Tel: 1-510-623-0500
Fax: 1-510-623-1092
Sales: [email protected]
Latin America Sales: [email protected]
Marketing: [email protected]
Web Site: http://www.abit-usa.com
RMA Center: http://rma.abit-usa.com/
UK and Ireland
Germany and Benelux (Belgium,
Netherlands, Luxembourg),
France, Italy, Spain, Portugal,
Greece, Denmark, Norway,
Sweden, Finland, and
Switzerland
Austria, Czech, Romania,
Bulgaria, Slovakia, Croatia,
Bosnia, Serbia, and Macedonia
Shanghai
Russia and CIS
ABIT Computer (U.K.) Corporation Ltd.
Unit 3, 24-26 Boulton Road, Stevenage,
Herts SG1 4QX, UK
Tel: 44-1438-228888
Fax: 44-1438-226333
E-mail: [email protected]
AMOR Computer B.V. (ABIT's European Office)
Jan van Riebeeckweg 15, 5928LG, Venlo,
The Netherlands
Tel: 31-77-3204428
Fax: 31-77-3204420
Sales: [email protected]
Web Site: http://www.abit.nl
Asguard Computer Ges.m.b.H
Schmalbachstrasse 5,
A-2201 Gerasdorf / Wien, Austria
Tel: 43-1-7346709
Fax: 43-1-7346713
E-mail: [email protected]
ABIT Computer (Shanghai) Co. Ltd.
Tel: 86-21-6235-1829
Fax: 86-21-6235-1832
Web Site: http://www.abit.com.cn
ABIT Computer (Russia) Co. Ltd.
Sales: [email protected]
Info: [email protected]
Web Site: http://www.abit.ru
User’s Manual
H-4
Appendix H
Poland
Japan
Taiwan Head Office
(Serving all other territories
not listed above.
Taiwan is 8+ GMT time,
and may have different holiday
calendar from yours.)
ABIT Computer (Poland) Co. Ltd.
Przedstawicielstwo w Polsce ul. Wita Stwosza 28,
50-149 Wrocław
Tel: 48 71 780 78 65 / 66
Fax: 48 71 372 30 87
Web Site: http://www.abit4u.jp
ABIT Computer Corporation
No. 323, Yang Guang St., Neihu,
Taipei, 114, Taiwan
Tel: 886-2-8751-8888
Fax: 886-2-8751-3382
Sales: [email protected]
Marketing: [email protected]
Web Site: http://www.abit.com.tw
7. RMA Service. If your system has been working but it just stopped, but you have not
installed any new software or hardware recently, it is likely that you have a defective
component. Please contact the reseller from whom you bought the product. You should be
able to get RMA service there.
8. Reporting Compatibility Problems to ABIT. Because of tremendous number of email
messages we receive every day, we are forced to give greater weight to certain types of
messages than to others. For this reason, any compatibility problem that is reported to us,
giving detailed system configuration information and error symptoms will receive the
highest priority. For the other questions, we regret that we may not be able to reply
directly. But your questions may be posted to the Internet news group in order that a
larger number of users can have the benefit of the information. Please check the news
group from time to time.
Thank You
ABIT Computer Corporation
http://www.abit.com.tw
KU8
">