SAMSUNG SUB-2000 N, P UTP camera User guide

Super High Resolution UTP Camera SUB-2000 User Guide

Before installing and operating this product, please read this manual thoroughly.

ENGLISH

Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we'll introduce our model description.

n SUB-2000 SERIES

• NTSC MODEL • PAL MODEL

SUB-2000N SUB-2000P n MODEL DESCRIPTION

SIGNAL SYSTEM

• SIGNAL SYSTEM

N → NTSC MODEL

P → PAL MODEL

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION -This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING : Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

WARNING : To prevent electric shock and risk of fire hazards:

◆ Do NOT use power sources other than that specified.

◆ Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

Contents

• Features ………………………………………………………………………… 5

• Warnings & Cautions ……………………………………………………… 6

• Precautions …………………………………………………………………… 7

• Components and Accessories …………………………………………… 9

• Overview ………………………………………………………………………… 9

• Installation …………………………………………………………………… 11

n

LENS

………………………………………………………………………………………… … 11… n

System Diagram

………………………………………………………………………… … 14 n

Using Coaxial Communications

……………………………………………………… … 15… n

RJ-45 Connector Schematic Diagram

……………………………………………… … 17

• Operating your Camera …………………………………………………… 18

n

Menu Configuration

……………………………………………………………………… …18…

… n

Menu Setup

… …………………………………………………………………………… …18…

… … •

LENS

……………………………………………………………………………………… …19…

… …

… …

•

EXPOSURE

… …………………………………………………………………………… …21…

•

WHITE BALANCE

… …………………………………………………………………… …22…

… …

… …

… …

… …

… …

… …

•

SSDR

……………………………………………………………………………………… …23…

•

BACKLIGHT

……………………………………………………………………………… …24…

•

SSNR3

…………………………………………………………………………………… …26…

•

DAY/NIGHT

… …………………………………………………………………………… …27…

•

SPECIAL

… ……………………………………………………………………………… …28…

•

EXIT

… …………………………………………………………………………………… …33

• Troubleshooting ……………………………………………………………… 34

• Specifications …………………………………………………………………… 35

COLOR CCD CAMERA 4 User Guide

Features

High Resolution

By adopting a diagonal 6mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, the camera produces clear picture quality with a horizontal resolution of 600 TV lines in color.

Excellent Sensitivity

The built-in high sensitivity COLOR CCD produces a clear image even in 0.05Lux(COLOR), 0.0001Lux

(COLOR, SENS-UP x512) or lower illumination.

SSNR3 (Samsung Super Noise

Reduction) Function

The high-performance W-V DSP chip effectively removes low-light gain noise and afterimage to provide clear images even in dark environments.

Electrical Day&Night

This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions.

The COLOR mode operates in daytime conditions to provide optimum colors, and B/W mode operates in nighttime conditions to enhance the definition of the image.

Motion Detection

Since the camera detects motion without any additional external sensor, you can monitor activity more efficient.

UTP TX

One UTP cable transmits power for the camera, video signals and RS-485 data; installation is easy and clean.(TIA/EIA-568B)

SSDR

(Samsung Super Dynamic Range)

For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting, this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness.

DIS (Digital Image Stabilizer)

The DIS function compensates for any camera movement, to produce more stable pictures.

Video/DC Drive Lens Support

You can select Video or DC Drive Lens from the menu.

Communication

RS-485 and Coaxial communication methods are supported.

- RS-485 Communications

: SAMSUNG-T, SAMSUNG-E, PELCO-D, PELCO-P,

BOSCH, HONEYWELL, VICON, PANASONIC.

- Coaxial Communications

: Pelco Coaxitron

Miscellaneous Functions

HLC(High Light Compensation), SENS-UP, FLIP (H/

V-REV), D-ZOOM, SHARPNESS and PRIVACY functions are provided.

OSD

The camera’s OSD is complimented by 18 languages.

- NTSC : English, Korean, Japanese, Spanish, French,

Portuguese, Taiwanese

- PAL : English, Chinese, German, Italian, French,

Spanish, Russian, Czech, Polish, Romanian,

Serbian, Swedish, Danish, Turkish, Portuguese

COLOR CCD CAMERA 5 User Guide

Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products.The Eco mark represents

Samsung Techwin ’s will to create environment-friendly products, and indicates that the product satisfies the EU RoHS Directive.

Warnings & Cautions

This information is provided to ensure your safety and to prevent any losses, financial or otherwise. Please read it carefully and use the product accordingly.

* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as an aerial ladder while providing after-sales service shall be at your expense.

* Separate the power plug during a thunder storm.

* This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or personal injuries by robbery, fire, natural disaster or other such events.

Warning/Attention/Special Mark Messages

Ignoring this information may result in material loss and / or serious personal injuries including death.

Ignoring this information may result in material loss and / or a slight injuries.

Indicates “Never Allowed.” Indicates “No Disassembling.”

Do not install under extreme temperature conditions.

Precautions

Do not install in high humidity environment.

Use only under temperature conditions between

-10ºC and +50ºC. Provide good ventilation when using in high temperature conditions.

May lower image quality.

Do not install under unstable lighting conditions.

Avoid touching the camera lens.

Severe lighting changes or flickering may hinder normal camera operation.

The lens is the most important component of the camera. Be careful not to smear it with fingerprints.

Do not drop the camera or subject it to physical shock.

Never keep the camera face to strong light directly.

COLOR CCD CAMERA 6 User Guide

May cause a product malfunction.

May damage the CCD.

COLOR CCD CAMERA 7 User Guide

Precautions

Do not expose the camera to radioactivity.

Do not expose the camera to rain or other types of liquids.

If exposed to radioactivity, the CCD will fail.

May cause a product malfunction.Wipe dry any liquids. Liquids may contain minerals that are corrosive to electronic components.

When connecting cables, be sure to read the instructions carefully and follow each step as instructed.

Failure to do so may result in critical system damage.

Notes

• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.

• Ensure that the power source complies with normal specifications before supplying it to the camera.

COLOR CCD CAMERA 8 User Guide

1 …

Components and Accessories

2 3 4 5

1 Super High Resolution UTP Camera SUB-2000

2 Auto iris lens connection plug

3 C-Mount adapter

4 Instruction manual

5 Power input terminal block

Front View

Overview

Side View

5

4

3

2

1

1…… : Please cover the CCD SENSOR when not using it.

2… C-Mount adapter

3… CS-Mount adapter

: Please install this adapter when using a C-Mount Lens.

: Please remove the C-MOUNT adapter and then attach it.

5… Auto Iris Lens Connector adjusting the Back Focal length.

COLOR CCD CAMERA 9 User Guide

Overview

Bottom View

Used to fix the camera on a bracket or tripod.

The screw sizes for this hole are as follows:

6

1/4"-20 UNC (20 THREAD)

L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard)

You can separate the Tripod Mounting Bracket and install it on the top or bottom of the camera. Make sure to use the Tripod Mounting

Bracket when fixing the camera to a bracket or tripod. Otherwise the camera may not be secure, or the internal circuitry of the camera may be damaged.

Rear View

7

9

❿

⓫

8

7 Function Setup switch

Display the menu on the screen and move the cursor in four directions to confirm status or after changing a selected item.

COLOR CCD CAMERA 10 User Guide

Overview

8 Power Video Output UTP Port

This port accepts power for the camera (AC 24V or AC 28V), outputs video, and facilitates RS-485 communication.

9 Power LED

This lamp is lit when the camera is receiving power normally.

❿ Power Input Terminal Block

If the UTP cable cannot be connected for power supply (distance over 300m(1000ft), for example), this cable is used instead for connecting DC 12V / AC 24V power to the camera using a separate adapter near by .

⓫ Video output terminal

Sends video signal and connects to the video input terminal of the monitor.

Installation

LENS

The lens is not supplied with this camera. Purchase a lens suitable for your environment.

This camera accepts the auto iris lens and both C-and CS-mount lens.

Notes

• To use the functions of this camera effectively it is recommended that a DC type Auto Iris lens is used.

• Keep the lens surface clean, if it becomes contaminated with dirt or fingerprints the picture quality suffers.

COLOR CCD CAMERA 11 User Guide

Installation

When Using Auto Iris Lens

1. Strip the insulation of the auto iris lens cable 8mm from the end.

2. Strip the insulation of the core of the auto iris lens cable to expose a 2mm length.

8mm

2mm

3. Remove the cover of the auto iris lens connector plug and solder the lens cable to the connector pin of the plug.

Pin No.

DC

LENS

VIDEO

No.1 Pin Damping Red (power)

No.2 Pin Damping + NC

No.3 Pin Drive + White (video signal)

No.4 Pin Drive Black (GND)

No.3 Pin

No.1 Pin

Lens cable

Connector

No.4 Pin

No.2 Pin

4. Please replace the auto iris lens connection plug cover and take off the CCD protection cap, and then attach the auto iris lens to the camera by screwing it in clockwise.

5. Please insert the connection plug that is connected to the auto iris lens cable into the auto lens connector, which is located on the side of the camera.

COLOR CCD CAMERA 12 User Guide

When using a C-Mount lens

Please take off the CCD protection cap and attach the C-Mount lens to the camera by screwing it in clockwise.

C-mount adapter

When using a CS-Mount lens

1. Please take off the CCD protection cap and C-mount adapter.

2. Please attach the CS-mount lens to the camera by screwing it in clockwise.

C-mount adapter

CS-mount adapter

CCD protection cap

Notes

• Please use the specified lens connection parts as shown in the picture below.

The use of the wrong sized parts may cause damage to the inside of the camera or result in poor fitting.

• Use of a lens which is too heavy affects the balance of the camera and may cause a malfunction. Please use a lens that weighs less than 450g.

• Please select Av mode if possible when adjusting the automatic light control(ALC) of an auto lens. Use of PK mode may cause hunting.

C-mount lens : 10 mm or less

CS-mount lens : 5 mm or less

COLOR CCD CAMERA 13 User Guide

Installation

System Diagram

UTP Power Supply Link Setup

1. SUB-2000 → 4CH Power Supply → 4Ch Receiver → DVR/Monitor/Controller

The maximum power transmission distance for the camera is 300m(1000ft), and the distance between the camera and the 4ch Receiver cannot exceed 900m(3000ft).

RS-485

VIDEO

SUB-2000

SPU-400T

300m(1000ft) or Less

900m(3000ft) or Less

SPU-400R

CH1 CH2 CH3 CH4

SCC-3100A

UTP CABLE

BNC CABLE

RS-485

2. UTP Receiver Link Setup(Additional Power input is needed)

SUB-2000 → 1Ch Passive Receiver → DVR → Monitor

225m(750ft) or Less

1Ch Passive Receiver

COLOR CCD CAMERA 14 User Guide

Notes

• Using the product with third-party UTP peripherals may result in degradation of product function and performance.

• Attenuation and distortion in signal may occur if the maximum transmission distance is exceeded. Please note that depending on the installation environment/condition, the signal may become attenuated and distorted and cause the camera to function incorrectly even when the transmission distance is within the maximum.

• If using RS-485 communication, please use the SAMSUNG-T, SAMSUNG-E, PELCO-D,

PELCO-P, BOSCH, HONEYWELL, VICON and PANASONIC Protocol.

• If you are using the 1Ch Passive Receiver system setup, please connect the adapter

(AC 24V or DC 12V) directly to the camera.

If the distance between the camera and the Power Supply exceeds

300m(1000ft), please connect an AC 24V or DC 12V adapter to the

Power Input Terminal Block(Accessory). Impressing power when the maximum transmission distance is exceeded may result in degradation of picture quality or even camera failure.

Using Coaxial Communications

• Coaxial Communications System

• OSD Control method

CAMERA

SET

UP

DOWN

LEFT

RIGHT

DVR

MENU/ENTER

UP KEY

DOWN KEY

LEFT KEY

RIGHT KEY

CONTROLLER

OSD KEY

JOYSTICK UP

JOYSTICK DOWN

JOYSTICK LEFT

JOYSTICK RIGHT

DVD

DVR

• : BNC

• ---- : RS-485

COLOR CCD CAMERA 15 User Guide

Installation

• Video Cable

The camera's video output port is connected to the monitor with a BNC coaxial cable, shown below : If the distance between the camera and the monitor exceeds the recommended maximum, please use an auxiliary video amp.

Distance

300m

450m

600m

Recommended Cable Specification

3C2V(RG-59/U)

5C2V(RG-6/U)

7C2V(RG-11/U)

Notes

• It is recommended that pure copper coax cable is used and not copper coated steel, as this will cause issues with the communication over the coaxial cable.

UTP CABLE

The camera uses UTP cable for transmitting video signals, power and transferring RS-485 control data.(TIA/EIA-568B)

6

7

4

5

8

2

3

No.

1

Line Color

White+Orange

Orange

White+Green

Blue

White+Blue

Green

White+Brown

Brown

Camera to Power Supply

VIDEO (+)

VIDEO (-)

RS485 (+)

POWER (-)

POWER (+)

RS485 (-)

POWER (+)

POWER (-)

CH1

Power Supply to Receiver

VIDEO (+) / RS-485 (+)

VIDEO (-) / RS-485 (-)

VIDEO (+) / RS-485 (+)

CH2

VIDEO (-) / RS-485 (-)

VIDEO (+) / RS-485 (+)

CH3

VIDEO (-) / RS-485 (-)

VIDEO (+) / RS-485 (+)

CH4

VIDEO (-) / RS-485 (-)

1

8

8

1

COLOR CCD CAMERA 16 User Guide

RJ-45 Connector Schematic Diagram

Copper Connector

UTP Coating

5

6

3

4

No.

1

2

7

8

Line Color

White+Orange

Orange

White+Green

Blue

White+Blue

Green

White+Brown

Brown

Camera to Power Supply

VIDEO (+)

VIDEO (-)

RS485 (+)

POWER (-)

POWER (+)

RS485 (-)

POWER (+)

POWER (-)

CH1

Power Supply to Receiver

VIDEO (+) / RS-485 (+)

VIDEO (-) / RS-485 (-)

CH2

CH3

CH4

VIDEO (+) / RS-485 (+)

VIDEO (-) / RS-485 (-)

VIDEO (+) / RS-485 (+)

VIDEO (-) / RS-485 (-)

VIDEO (+) / RS-485 (+)

VIDEO (-) / RS-485 (-)

The SUB-2000 uses UTP cable to receive its power (AC 24V or AC28V) from the Power Supply.

Therefore, a separate adapter is not required. Please refer to the RJ-45 Connector Schematic

Diagram.

COLOR CCD CAMERA 17 User Guide

LENS

EXPOSURE

WHITE BAL

SSDR

BACKLIGHT

SSNR3

DAY/NIGHT

SPECIAL

EXIT

Operating Your Camera

Menu Configuration

MAIN SETUP

●DC… ●VIDEO… ●MANUAL

●BRIGHTNESS… ●SHUTTER………………… ●AGC………

●SENS-UP

●ATW…

●RETURN

●OUTDOOR… ●INDOOR…

●MANUAL…

●OFF…

●

OFF

…

●AWC→SET

●ON

●

BLC

… ●

HLC

●

ON

…

●

COLOR

…

●

OFF

●

B/W

… ●

AUTO

●

IMAGE ADJ

… ●

MONITOR

… ●

CAM TITLE

…

●

SYNC

●

MOTION DET

… ●

PRIVACY

……

●

COMM ADJ

… ●

LANGUAGE

… ●

RETURN

●

SAVE

… ●

NOT SAVE

… ●

RESET

Menu Setup

Use the Function Setup switch within the camera.

Function Setup switch

1. Press the Function Setup switch.

• Main SETUP menu is displayed on the monitor screen.

COLOR CCD CAMERA 18 User Guide

Select the function using the Function Setup switch.

MAIN SETUP

1.LENS DC

2.EXPOSURE

3.WHITE BAL ATW

4.SSDR

5.BACKLIGHT

6.SSNR3

7.DAY/NIGHT

8.SPECIAL

9.EXIT

OFF

OFF

ON

COLOR

SAVE

Change the status using the Function Setup switch.

2. Select a desired function using the Function Setup switch.

• Place the cursor over a desired item.

3. Set up a selected item by using the Function Setup switch.

4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.

Notes

• An item with the… icon also has sub menus. To select a sub menu, select an item with the icon and press the Function Setup switch.

• An item with the --- icon is unavailable due to function settings.

LENS

Using this function, you can control the screen brightness.

1. When the SETUP menu screen is displayed, select‘LENS’by using the Function Setup switch so that the arrow indicates‘LENS’

2. Select the connected lens type by using the Function Setup switch.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

COLOR CCD CAMERA 19 User Guide

Operating Your Camera

DC/Video : Select Auto Iris Lens.

You can adjust the minimum shutter and maximum value of ESC shutter mode when DC Lens mode is selected.

Manual : Select Manual Lens

3. Each Lens mode has sub menu site as listed below.

- Brightness (DC, Manual) : Adjusts the video brightness.

- Level (VIDEO) : Adjusts the level of video iris signals; the higher the level, the brighter the video looks.

- FOCUS ADJ (DC, VIDEO) : To adjust the DC and VIDEO lens focus correctly, you must activate the Focus Settings mode under each lens menu. To activate the Focus Settings mode, adjust the lens focus, and

- IRIS SPEED (DC) then deactivate the settings mode. (The VIDEO lens requires an extra step: go to the sub menu of the Focus Settings mode and change the shutter speed to adjust the lens brightness.)

: Adjusts the Iris control speed of the DC lens. If the control speed is too slow or fast, please use this menu to adjust the speed.

Notes

• When using VIDEO lens, adjust the lens VR explained below first and set the focus using

'FOCUS ADJ' menu.

• If color rolling occurs when using a DC lens, set Shutter to ---.

• Some lenses may not work properly, depending on the setting of the BRIGHTNESS LEVEL.

• When Using a Video-Type Auto Iris Lens

❶ ………

(Average).

2 …… to the optimal value.

3 ……

4 …… changes properly. Otherwise, adjust the Lens VR again.

COLOR CCD CAMERA 20 User Guide

EXPOSURE

MAIN SETUP

1.LENS DC

2.EXPOSURE

1. When the SETUP menu screen is displayed, select 'EXPOSURE’ by using the Function

Setup switch so that the arrow indicates 'EXPOSURE’.

2. Select a desired mode using the Function Setup switch.

EXPOSURE SETUP

1.BRIGHTNESS

2.SHUTTER

3.AGC

4.SENS-UP

5.RETURN

25

ESC

HIGH

OFF

SHUTTER : You can select the shutter.

- ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject.

- MANUAL : You can control shutter speed manually.

(NTSC MODEL : 1/60sec~1/120,000sec, PAL MODEL : 1/50sec~1/120,000sec)

- A.FLK : Select this when you experience picture flicker, this happen when there

- --- is a clash with the installed lighting frequency.

: Shutter speed is fixed at 1/60sec(1/50sec).

Notes

• When you use a DC lens, set the shutter mode to --- if color rolling occurs.

• When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the picture may become unstable if the camera faces a bright fluorescent light. Therefore, take care when choosing the installation position.

• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.

COLOR CCD CAMERA 21 User Guide

Operating Your Camera

AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but the greater the noise.

- HIGH : Allows automatic gain control from 5.3dB to 37dB.

- OFF : Deactivates the AGC function.

- LOW : Allows automatic gain control from 5.3dB to 32dB.

SENS-UP : When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated.

- OFF : Deactivates the SENS-UP function.

- AUTO : Activates the SENS-UP function.

Notes

• If you set the Function Setup switch to ‘AUTO’ mode, You can adjust the brightness by increasing or decreasing the shutter speed. (x2 ~ x512)

• Note that the higher the zoom level, the brighter the screen, but the more likely it is that an after-image will appear.

• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the zoom level is increased, this is normal.

RETURN : Select this to save the changes in the EXPOSURE menu and return to the

SETUP menu.

White Bal (White Balance)

Use the White Balance function to adjust the screen color.

1. When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function

Setup switch so that the arrow indicates ‘White Bal’ .

2. Select a desired mode using the Function Setup switch.

MAIN SETUP

1.LENS DC

2.EXPOSURE

3.WHITE BAL ATW

COLOR CCD CAMERA 22 User Guide

※ Select one of the following 5 modes, as appropriate for your purpose.

ATW : Select this when the color temperature is between 1,700˚K and

11,000˚K.

OUTDOOR : Select this when the color temperature is between 1,700˚K and

11,000˚K. (sodium light inclusion)

INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.

MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that switch to MANUAL mode, finetune the White Balance and the Function Setup switch.

AWC →SET : To find the optimal luminance level for the current environment, point the camera towards a sheet of white paper and press the Function Setup switch. If the environment changes, readjust it.

Notes

• White Balance may not work properly under the following conditions. In this case select the AWC mode.

❶ ………… control range (e.g. clear sky or sunset).

2… When the ambient illumination of the subject is dim.

If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.

SSDR (Samsung Super Dynamic Range)

SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas.

MAIN SETUP

1.LENS DC

2.EXPOSURE

3.WHITE BAL

4.SSDR

ATW

OFF

COLOR CCD CAMERA 23 User Guide

Operating Your Camera

1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the Function Setup switch so that the arrow indicates ‘SSDR’.

2. Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas.

SSDR ON SSDR OFF

BACKLIGHT

The SUB-2000 is designed so that it delivers a distinctive subject and background at the same time, even when the subject is in backlight, by adopting a function of the proprietary

W-V DSP chip.

1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function

Setup switch so that the arrow indicates ‘BACKLIGHT’.

MAIN SETUP

1.LENS DC

2.EXPOSURE

3.WHITE BAL ATW

4.SSDR

5.BACKLIGHT

OFF

OFF

2. Select a desired mode using the Function Setup switch depending on the camera purpose.

OFF : Not being used

BLC : Enables a user to select a desired area on a picture and view that area more clearly.

- LEVEL : Adjust level of the BLC function.

COLOR CCD CAMERA 24 User Guide

- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.

HLC (High Light Compensation) :

If the scene contains extremely bright light areas such as; from car headlight, the light can mask out much of the on-screen detail.

- LEVEL : Adjust level of the HLC function.

- LIMIT : Enable to change the operating condition.

- MASK COLOR/TONE : Change the color / brightness of the masking area.

(Black, Red, Blue, Cyan, Magenta)

- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.

3. Select a desired mode using the Function Setup switch.

Select ‘BLC’ to adjust the area to be

enhanced then adjust the level.

HLC : Enable the user to change the level, limit, mask color/tone and area.

Notes

• Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance.

• When dark, the HLC is only activated when a bright light exceeding a specific size. (In

NIGHT ONLY mode).

• The HLC is not activated in day light or when bright light is not present at night. (In NIGHT

ONLY mode).

COLOR CCD CAMERA 25 User Guide

Operating Your Camera

SSNR3

This function reduces the background noise in a low luminance environment.

1. When the SETUP menu screen is displayed, select ‘SSNR3’ by using the Function Setup switch so that the arrow indicates ‘SSNR3’.

MAIN SETUP

1.LENS DC

2.EXPOSURE

3.WHITE BAL

4.SSDR

5.BACKLIGHT

6.SSNR3

ATW

OFF

OFF

ON

2. Select a desired mode using the Function Setup switch.

ON : Activates SSNR3 so that noise is reduced.

OFF : Deactivates SSNR3. Noise is not reduced.

3. Set the SSNR3 mode to ‘ON’ and press the Function Setup switch. Then you can adjust the noise reduction level.

Notes

• You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the 'EXPOSURE' menu is ‘OFF’.

• When adjusting the noise reduction level in the SSNR3 mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image.

COLOR CCD CAMERA 26 User Guide

DAY/NIGHT

You can display pictures in color or in black and white.

1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Function

Setup switch so that the arrow indicates ‘DAY/NIGHT’.

MAIN SETUP

1.LENS DC

2.EXPOSURE

3.WHITE BAL ATW

4.SSDR

5.BACKLIGHT

6.SSNR3

7.DAY/NIGHT

OFF

OFF

ON

COLOR

2. Select a desired mode using the Function Setup switch according to the picture display you want.

COLOR : The picture is always displayed in color.

B/W : The picture is always displayed in black and white.

You can turn on or off the burst signal on B/W mode.

AUTO : The mode is switched to ’Color‘ in a normal environment, but switches to ’B/W‘ mode when ambient illumination is low. To set up the switching time for AUTO mode, press the

Function Setup switch.

You can turn on or off the burst signal on

B/W mode.

- DWELL TIME : You can select day/night switching delay time from. …

→5s, 7s, 10s, 15s, 20s, 30s, 40, 60s

Notes

• When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching between Color and Black & White may not occur.

• When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as selecting 'AUTO' mode cannot be selected.

COLOR CCD CAMERA 27 User Guide

Operating Your Camera

SPECIAL

1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup switch so that the arrow indicates ‘SPECIAL’.

MAIN SETUP

1.LENS DC

2.EXPOSURE

3.WHITE BAL ATW

4.SSDR

5.BACKLIGHT

6.SSNR3

7.DAY/NIGHT

8.SPECIAL

9.EXIT

OFF

OFF

ON

COLOR

SAVE

2. Select a desired mode using the Function Setup switch.

SPECIAL

1. IMAGE ADJ

2. MONITOR

3. CAM TITLE

4. SYNC

5. MOTION DET

6. PRIVACY

7. COMM ADJ

8. LANGUAGE

9. RETURN

LCD

OFF

INT

OFF

OFF

ENGLISH

IMAGE ADJ :

1) When the SPECIAL menu screen is displayed, select ‘IMAGE ADJ’ by using the

Function Setup switch so that the arrow indicates ’IMAGE ADJ‘.

2) Select a desired mode using the Function Setup switch.

COLOR CCD CAMERA 28 User Guide

IMAGE SETUP

1. V-REV

2. H-REV

3. D-ZOOM

4. DIS

5. FONT COLOR

6. SHARPNESS

7. RETURN

OFF

OFF

OFF

OFF

WHITE

ON

• V-REV

• H-REV

: You can flip the picture vertically on the screen.

: You can flip the picture horizontally on the screen.

• D-ZOOM : You can use a digital zoom of x1 ~ x16.

• DIS (Digital Image Stabilizer) : This function mitigates any picture movement due to external factors such as wind.

• FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue)

• SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of

• RETURN the picture.

: Select this to save the settings for the IMAGE ADJ menu and to return to the SPECIAL menu.

Notes

• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.

• If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear.

• As the DIS function uses the digital zoom, the camera's resolution will decrease.

• DIS doesn’t operate when background illumination is too low.

• DIS doesn’t operate when object pattern is monotonic as like sky or white wall.

Monitor : Please change the settings value of video appropriate to your monitor.

- LCD : Please select this menu item when using an LCD monitor.

You can change the gamma, PED level and color gain in the sub menus.

- USER : Please use this menu item when using a monitor other than standard ones. You can

COLOR CCD CAMERA 29 User Guide

Operating Your Camera change the gamma, PED level and color gain in the sub menus.

- CRT : Please select this menu item when using a CRT monitor. You can change the PED level, color gain in the sub menus.

CAM TITLE : If you enter a title, the title will appear on the monitor.

1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘CAM TITLE’.

CAMERA TITLE SETUP

2) Set it to ‘ON’ by using the Function Setup switch.

3)

Press the Function Setup switch.

4) Use the Function Setup switch to move to a desired letter and select the letter by pressing the Function Setup switch.

Repeat this to enter multiple letters. You

A B C D E F G H I J K L M

N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z

- . 0 1 2 3 4 5 6 7 8 9

← → C L R P O S E N D can enter up to 15 letters.

5) Enter a title, move the cursor to ‘POS’ and press the Function Setup switch. The entered title appears on the screen. Select the position to display the title on the screen by using the Function Setup switch and press the

Function Setup switch. When the position is determined, select ‘END’ and press the Function

Setup switch to return to the SPECIAL menu.

FRONT DOOR

Notes

• When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one.

• Only English is available in this mode.

• If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the

Function Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch.

COLOR CCD CAMERA 30 User Guide

SYNC : In areas where the supply is at 60Hz(NTSC),

50Hz(PAL) frequency, you can synchronize the output phase of multiple cameras using the power synchronization function (Line-Lock) without using a synchronization signal generator.

- INT : Internal Synchronization Type

- L/L : Power Synchronization Type, Line-lock

• Press the Function Setup switch.

• You can select a desired phase from 0 to 359 when select 'phase'.

Notes

• When using AC power at 60Hz(NTSC), 50Hz(PAL) frequency, you can use the L/L type synchronization.

• When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.

• When using RJ-45 Connector, you can't use the L/L type synchronization.

MOTION DET :

This product has a feature that allows you to observe movement of objects in 8 different areas on the screen, and the words 'MOTION DETECTED' appear on the screen when movement is detected.

You can monitor activity more efficient.

… 1) When the SPECIAL menu screen is displayed, press the Function Setup switch so

.

… 2) …Set up the mode using the Function Setup switch.

- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement.

- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.

- SEL POS : Determines which of the 4 vertices of each MD area is to be used.

- XPOS

- YPOS

: Determines the coordinate of the horizontal axis for SEL POS.

: Determines the coordinate of the vertical axis for SEL POS.

COLOR CCD CAMERA 31 User Guide

Operating Your Camera

- FILL→SET : Fills in a selected MD area. The color of filling is sequentially selected as brown, orange, blue, cyan, green, yellow, magenta and red.

- RETURN : Select this to save the MOTION DET menu settings and return to the

SPECIAL menu.

PRIVACY : Mask an area you want to hide on the screen.

PRIVACY AREA SETUP

1.AREA

2.MODE

3.MASK COLOR

4.MASK TONE

5.TOP

6.BOTTOM

7.LEFT

8.RIGHT

9.RETURN

AREA1

OFF

GREEN

1

39

79

13

52

1) … When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates ‘PRIVACY’.

… … 2) … Set up the mode using the Function Setup switch.

- AREA

- MODE

: You can select up to 12 PRIVACY areas.

: Determines whether to use the area selected in the AREA.

- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray.

- MASK TONE : Adjust the brightness of MASK COLOR.

- TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area.

- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.

COMM ADJ (Communication Adjustment) :

This function sets up the camera communication status when controlling the camera through an external control device.

… 1) … When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates ‘COMM ADJ’.

… … 2) … Set up the mode using the Function Setup switch.

COLOR CCD CAMERA 32 User Guide

- CAM ID : Determines the camera's identification number

(between 0 and 255).

- BAUD RATE : You can select 2400/4800/9600/19200/38

400/57600 bps.

- UART MODE : You can select NONE, EVEN or ODD for the parity bits.

- RET PKT : Determines whether to send a command back to the controller device when a communication control command is sent to the camera.

- DISP ID : Display camera title on top left corner of the screen.

- PROTOCOL : Select the communication PROTOCOL.

(SAMSUNG-T, SAMSUNG-E, PELCO-D, PELCO-P, BOSCH, HONEYWELL, VICON and

PANASONIC)

- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.

* Initial value of communication adjustment

Item

Initial value

Camera ID BAUD RATE UART MODE PET PKT

1 9600 8-NONE-1 ENABLE

Notes

• As below, the names of protocol have been changed.

- STW(SPD) → SAMSUNG-T

- SEC → SAMSUNG-E

LANGUAGE : You can select the menu language according to your requirements.

RETURN : Select this to save the SPECIAL menu settings and return to the MAIN

SETUP menu.

EXIT

Select a desired EXIT mode using the Function Setup switch depending on the camera purpose.

- SAVE : Save the current settings and exit the MAIN SETUP menu.

- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.

- RESET : Resets the camera settings to the factory defaults. Communication,

Language and Monitor settings are not initialized.

COLOR CCD CAMERA 33 User Guide

Troubleshooting

If you have trouble operating your camera, refer to the following table.

If the guidelines do not enable you to solve the problem, contact an authorized technician.

● Nothing appears on the screen.

▶ Check that the power cord and line connection between the camera and monitor are properly connected.

▶ Check that you have properly connected UTP cable or BNC cable to the camera.

▶ Check the type of lens.

▶ Check the pin arrangement for the UTP cable.(TIA/EIA-568B)

● The image on the screen is dim.

▶ Is lens stained with dirt? Clean your lens with soft, clean cloth.

▶ Set the monitor to the proper condition.

▶ If the camera is exposed to very strong light, change the camera position.

● The image on the screen is dark.

▶ Adjust the contrast feature of the monitor.

▶ If you have an intermediate device, set the 75Ω / Hi-z properly.

● The camera is not working properly, and the surface of the camera is hot.

▶ Check that you have properly connected the camera to an appropriate power source.

● The SENS-UP function does not work.

▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.

▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.

● The Motion Detection function does not work.

▶ Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.

● Color is not correct.

▶ Check the setting of WHITE BAL SETUP menu .

● The screen flickers continually.

▶ Ensure the camera is not pointing towards the sun.

● When coaxial communication is not available:

▶ Make sure that the camera and monitor are installed within the recommended distance.

▶ Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded.

● Picture is distorted.

▶ Check the length of the UTP cable (900m(3000ft) or less).

● The camera does not work, and the video feed from the camera is not being received.

▶ Check the Power Supply to see whether the connection status and pin arrangement for the camera's UTP cable and the Camera Input UTP cable are normal.

COLOR CCD CAMERA 34 User Guide

Specifications

ELECTRICAL

Input Voltage

Power Consumption

VIDEO

Imaging Device

Total / Effective Pixels

Scanning System

Synchronization

Frequency

Horizontal Resolution

Min. Illumination

S/N (Y Signal)

Video Output

UTP Output

OPERATIONAL

Electronic Shutter Speed

Shutter Mode

SUB-2000N

AC 24V ±10% / AC 28V ±10% / DC12V±10%

Max 3.5W

SUB-2000P

1/3 inch, Diagonal 6mm Super HAD CCD

811(H) x 508(V) / 768(H) x 494(V)

2:1 Interlace

Internal / Line-Lock

H : 15.734KHz / V : 59.94Hz

795(H) x 596(V) / 752(H) x 582(V)

H: 15.625KHz / V: 50.00Hz

600TVL

0.05 Lux (50IRE, @F1.2), 0.0001Lux (SENS-UP, x512)

52dB (Weight On, AGC OFF)

CVBS : 1.0Vp-p, 75Ω composite

Built-in UTP TX (Maximum transmission length 900m(3000ft)) : Balanced differential signal 100Ω

On Screen Display

SSDR

Backlight Compensation

Day & Night

Gain Control

White Balance

SENS-UP

Motion Detection

Privacy Masking

SSNRIII

Digital Zoom

DIS

Camera Title

Sharpness

Flip / Mirror

Coaxial Communication

RS-485 Communication

ENVIRONMENTAL

Operating Temperature / Humidity

MECHANICAL

Lens Mount

Back Focus Adjustment

Dimension / Weight

1/60sec~1/120ksec

ESC, MANUAL, A.FLK, FIXED

1/50sec ~ 1/120ksec

NTSC : English, Korean, Japanese, Spanish, French, Portuguese, Taiwanese

PAL : English, Chinese, German, Italian, French, Spanish, Russian, Czech, Polish,

Romanian, Serbian, Swedish, Danish, Turkish, Portuguese

ON / OFF (Level adjustable)

BLC / HLC / OFF

COLOR / B/W / AUTO

LOW / HIGH / OFF

ATW / OUTDOOR / INDOOR / MANUAL / AWC (1,700°K ~ 11,000°K)

Auto / OFF (Selectable x2 ~ x512)

ON / OFF (8 Programmable zones)

ON / OFF (12 Programmable zones)

ON / OFF (Level adjustable)

ON / OFF (x1 ~ x16)

ON / OFF

ON / OFF (Display 15 Characters)

ON / OFF (Level adjustable)

ON / OFF

Pelco Coaxitron

SAMSUNG-T, SAMSUNG-E, PELCO-D, PELCO-P, BOSCH, HONEYWELL, VICON, PANASONIC

-10°C ~ +50°C / 30% ~ 80% RH

C / CS Mount

Manual

58(W) x 52(H) x 121(D) / 290g

※ The specification for this product may change without prior notice for product improvement.

※ This specification is based on a transmission distance of 500 meters; in cases of long-distance transmissions, some degradation in picture quality may occur depending on the operating environment.

COLOR CCD CAMERA 35 User Guide

DECLARATION OF CONFORMITY

Application of Council Directive(s)

Manufacturer's Name

Manufacturer's Address

European Representative Name

European Representative Address

Equipment Type/Environment

Model Name

Beginning Serial NO.

Year of Manufacture

Conformance to

2004 / 108 / EC

SAMSUNG TECHWIN CO., LTD

SAMSUNG TECHWIN CO., LTD

42, SUNGJU-DONG CHANGWON-CITY,

KYUNGNAM, KOREA, 641-716

CCTV Camera

SUB-2000P

C5436V3Z200001X

2010.02.01

EN 55022 : 2006

EN 50130-4 : 2003

We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).

Manufacturer SAMSUNG TECHWIN CO., LTD

Signature

Full Name BONJENG GU

Position

Place

Date

QUALITY CONTROL MANAGER

CHANGWON, KOREA

2010.02.01

Legal Representative in Europe

Signature

Full Name

Position

Place

Date

COLOR CCD CAMERA 36 User Guide

MEMO

COLOR CCD CAMERA 37 User Guide

MEMO MEMO

COLOR CCD CAMERA 38 User Guide COLOR CCD CAMERA 39 User Guide

SALES NETWORK

•

SAMSUNG TECHWIN CO., LTD.

Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400

TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745

•

SAMSUNG TECHWIN AMERICA Inc.

1480 Charles Willard St, Carson, CA 90746, UNITED STATES

Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com

www.samsungtechwin.com

www.samsungsecurity.com

•

SAMSUNG TECHWIN EUROPE LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business

Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS

TEL : +44-1932-45-5300 FAX : +44-1932-45-5325

P/No. : Z6806-1090-02A

VAN 10. 04