Shinybow USA SB-5645 Instruction manual

M U L T I M E D I A A U D I O A N D V I S U A L

In st ru ction Manual

MODEL : SB-5645

4x4 HDMI MATRIX SWITCHER

HDMI Matrix Switcher Series

Thank you for purchasing the SB-5645 4x4 HDMI Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual throughly before attempting to use 4x4 HDMI Matrix switcher.

Part No.: ENCL005645000A2

SAFETY INFORMATION

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK),

NO USER SERVICEABLE PARTS INSIDE,

REFER SERVICING TO QUALIFIED SERVICE PERSONAL.

This symbol is intended to alert the user to the presence of uninsulated of uninsulated “dangerous voltage” within the products enclosure that enclosure tha may be of sufficientmagnitude to constitue a risk of electric shock to persons.

Caution:

This symbol is intended to alert the user to the presence of important operational and maintenance (serving) instructions in the literature accompanying the appliance.

extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

fully insert.

1.

Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original

factory packing.

2.

Read all documentation before operating your equipment. Retain all documentation for future reference.

3.

Follow all instructions printed on unit chassis for proper operation.

4.

Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

5.

Make sure power outlets conform to the power requirements listed on the back of the unit.

6.

Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on

or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit

from the appliance.

7.

Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of

a piece of equipment is not defeated.

8.

Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by

any warranty.

9.

Power down & disconnect unit from mains voltage before making connections.

10.

Never hold a power switch in the ＂ON＂ position.

11.

Do not use the unit near stoves, heat registers, radiators, or other heat Producing devices.

12.

Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be

Periodically ＂blown free＂ of foreign matter.

13.

Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts inside.

14.

15.

Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time.

16.

Service Information Equipment should be serviced by qualifier service personnel when:

A.

The power supply cord or the plug has been damaged.

B.

Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

IMPORTANT SAFETY INSTRUCTIONS

To insure the best from this product, please read this manual carefully. Keep it in a safe place for future reference.

To reduce the risk of electric shock, do not remove the cover from the unit. No user serviceable parts inside. Refer servicing to qualified personnel.

To reduce the risk of fire, do not expose the unit to rain, water or excessive moisture.

Do not force switched or external connections.

When moving the unit disconnect the serial port connections first then the power cable and finally the interconnecting cables to other devices.

Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Use a clean dry cloth.

Installation of this unit should be in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

SB-5645 INSTRUCTION & OPERATION MANUAL

TABLE OF CONTENTS

11

12

13

14

08

09

10

03

04

05

06

07

18

19

20

21

15

16

17

22

23

PAGE 3

INTRODUCTION AND PACKAGE CONTENTS

INTRODUCTION

The SB-5645 is high-performance 4x4 matrix routing switcher for HDMI signals. This switcher supports data rates up to 6.75 Gbps, enabling 1080p HDMI formats and UXGA/WUXGA/DVI resolution to any HD display. High Definition Digital signals can be selected and distributed to any 4 outputs simultaneously.

Support high resolution HDMI sources routed to HDMI displays, monitors, projector or audio receivers.

The EDID can be selected between seven (8) different modes. Control is provided via Front panel push buttons, IR remote or via RS-232. An RS232 Windows GUI interface is provided for matrix routing.

PACKAGE CONTENTS

1. Main console unit

2. Operating Instructions

3. IR Remote Controller (SW-5645E)

4. 19 inch Ear mount bracket (Part # 1U-440L)

5. IR Extender receiver (SB-100)

6. CD Contents: This manual, Windows GUI

7. RS232 Cable

8. Power Supply 12VDC, 3A Universal Type 50/60Hz, 100~230 VAC

PAGE 4


INTRODUCTION AND PACKAGE CONTENTS

FEATURES

1. 4x HDMI digital source devices matrix switched to 4x HDMI devices.

2. HDMI digital video w/embedded audio, DVI format and CEC/HDCP 2.0 compliant

3. Seven (7) function key control and worldwide EDID modes for HDTV resolutions.

4. Link speeds of up to 6.75 Gbps (link clock rate of 225Mb Hz), Support HDMI 1.4a 3D formats.

5. Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and

HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p

6. Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV

and audio receivers/amplifiers.

7. Digital Video TMDS formats Resolutoin up to 1080P-60 with Deep color 36-bit.

8. Digital Audio Support : - Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex,

- DTS, DTS-HD, DTS-HD Master, DTS-EX

- PCM, PCM2, LPCM2..

9. Various User Interface control:

‧Windows based GUI control via RS232 port

‧Front Panel push button

‧IR wireless remote control

‧Third party RS232 controller (via simple ASCII)

10. Support world wide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK

11. Support EDID modes :

Internal modes : AUTO/1080P-2CH/1080P-5.1/1080P-7.1/1080i-2CH/720P-2CH

External modes : Passing mode.

12. Automatic scanning input & output status via LED show on front panel.

13. Support IR Remote and IR Extender with distance up to ~ 1000' (300M) Maximum.

14. EDID configuration via Internal modes.

15. Consumer Electronic Control (CEC) switch all open or OFF

The Switcher will remember that last state during a power cycle.

When power is removed and resorted, the last configuration will be invoked.


PAGE 5

SPECIFICATIONS

SPECIFICATIONS

Type of HDMI Switcher

HDMI Support

HDCP / CEC Support

Video Bandwidth

Digital Video Support

Digital Audio Support

Controls

4x HDMI inputs To 4x HDMI Outputs Matrix Switcher

HD 1080P-@60Hz, H36-bit Deep color, 3D (1.4a) formats.

HDCP 2.0 Compliant, CEC Compliant.

Double Data Rates:225Mhz, Total 6.75Gbps bandwidth.

Full HD resolution : 480i / 480p / 720p / 1080i / 1080p

Multi Audio Formats 5.1 / 7.1, MAT(MLP)

Dolby Digital,

Dolby TrueHD,

Dolby Digital Plus,

DTS, DTS-ES 6.1,

DTS-HD, DTS-HD-HRA, DTS-HD Master,

(PCM-2CH)

IR Remote Controller

IR External port x 1 (OD 3.5mm Ear phone Jack)

Select & Function buttons on front panel

RS 232 series interface

Preview output

Source Status

Function Control Key

Infrared Frequency

IR External Distance

HDMI I/O Connector

Temperature

Dimensions

Rack Mount

Power Supply

Power Consumption

Safety Approvals

Product Weight

Automatically Scan Sources Inputs via LED

ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID

38 Khz

~1000 feet / 300 meters maximum.

HDMI Type A - SMD 19pin Female Type

32 F - 100 F Operation (0 C - 38 C)

LxWxH=19 ”x 9.85 ” x 1.75 ”(482mm x 250mm x 44mm)

Rack Mount 1RU High 19 ”Rack Mount (with rack mount)

DC12V / 3A, Universal world wide Type 50/60Hz, 100~230 VAC

2150 mA Maximum

CE, FCC, RoHS (2002/95/EC).

1.85 Kgs / 3.08 lb

As product improvement is continuous, specifications are subject to change and without notice or liability.

PAGE 6


EDID FUNCTION

EDID function Setup

EDID setup

Step 1 . Press the EDID button

To change the EDID setup

The display will show the currently selected EDID mode

Step 2 . Press SOURCE #1 or #2 button row

The button will flash blue and the display will show the current Embedded EDID Status.

Step 3 . Press the ENTER button

To set EDID mode.

The switcher will return to operation mode.

Operation will abort if no keys are pressed within 5 seconds.

6.1 Embedded EDID modes

Embedded EDID setup

Total 8 EDID Modes to select EDID mode.

Press EDID > SOURCE > ENTER

SOURCE #1

or

SOURCE #2

Repeatedly depressing the source 1 button will cycle up thru the options.

Repeatedly depressing the source 2 button will cycle down thru the options.

Embadded EDID :

Mode 1 : FSS

Mode 2 : H24-3D

Mode 3 : H24M-3D

Mode 4 : H36

Mode 5 : H36M

Mode 6 : H36-3D

Mode 7 : H36M-3D

Mode 8 : AUTO


PAGE 7

EDID FUNCTION

EDID function : 8x Embedded EDID Modes

Automatic capture most suitable EDID from

Destination to Source.

Mode 2 .

H24-3D (1080p-24 bits)

Audio Support :

PCM 2CH

Mode 3 .

H24-3D-M (1080p-24bits)

Audio Support :

MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 5.1CH,

DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH

Mode 4 .

H36 (1080p-36 bits)

Audio Support :

PCM 2CH

Mode 5 .

H36-M (1080p-36 bits)

Audio Support :



Mode 6 .

H36-3D (1080p-36 bits)

Audio Support :

PCM 2CH

Mode 7 .

H36-3D-M (1080p-36 bits)

Audio Support :



Mode 8 .

AUTO <Default>

All Outputs will be set to the highest common resolution of all connected display devices.

PAGE 8


EDID FUNCTION

EDID function for HDMI Matrix Switcher

6.2 LEARNING EDID Learning EDID from Destination to Source

Learning EDID setup

Press

EDID > DESTINATION > SOURCE > ENTER

Switcher will LEARN destination EDID and pass the selected source.

NOTE : The already learned EDID cannot be modified. You can only rebuild a new Learning EDID.

For example;

When the Source has "Learned" the EDID data from a destination, It will save that EDID information into EPROM and the EDID data cannot change.

Please select new learning destination to sources or change to one of the embedded EDID modes when you want to remove the learning EDID memory from EPRPM .


PAGE 9

EDID FUNCTION

EDID Function : LEARNING

6.2.1

Learning EDID Single to Single

Step 1 .

Press EDID button

Step 2 .

Press the Destination #4 button row

Step 3 .

Press the Source #3 button row

Step 4 .

Press ENTER button

Example : Learn Destination #4 EDID To Source #3.

The button will flash blue and the display will show the current Embedded EDID Status.

Copy the Destination #4 Display EDID.

Learning the Destination #4 EDID To Source # 3.

To confirm entries.

Learning EDID Single to multiple

Step 1 .


Learning destination EDID link to the majority Sources


Step 2 .

Press the Destinations #1~4 button row Copy any 1~4 Destinations EDID.

Step 3 .

Press the Source #1, #3,#4 button row Learning the Destination EDID link to source #1,#3,#4 .

Step 4 .

Press ENTER button To confirm entries.

6.2.3

Learning EDID Single to ALL

Step 1 .


Step 2 .

Press destination button 1 thru 4

Step 3 .

Press ALL button

Step 4 .

Press ENTER button

Learning destination EDID link to All Sources


Learning anyone 1~4 Destination EDID to all sources.

Learning selected destination EDID to all sources.

To confirm entries.

PAGE 10


EDID FUNCTION

EDID function for HDMI Matrix Switcher

6.3 EDID status

Step 1 .


Step 2 .


To view the current EDID status.

The button will flash blue and the display will show the current Embedded EDID Status.

To exit.

6.4

R

How to setup FSS Function

R

Fast speed start

Step 1 . Press the Destination #1~4 button row

Then Press the Source #1~4 button row

To setup and Install all devices.

Step 2 . Press EDID button Select a optimum status of Embedded EDID mode.

Step 3 . Press ENTER button

Step 4 .

Press EDID button

Step 5 . Press ENTER button

To conform entries.

R

To select the EDID FSS mode.

To conform entries.

6.5 LEARNING EDID definition Learning EDID from Destination to Source

1. Switcher will LEARN destination EDID and pass the selected source.

2. To set up learning between a single destination and single source:

Press EDID button > Press Destination 1 thru 4 > Press Source 1 thru 4 > Press ENTER to confirm.

Switcher will learn destination EDID to source device.

3. To set up learning between a single destination and Multiple sources:

Press EDID button > Press Destination 1 thru 4 > Press the majority Sources 1 thru 4 > Press ENTER.

Switcher will learn single destination EDID to many source devices.

4. How to Learning single destinations with all sources.

Press EDID button > Press ALL button > Press ENTER to confirm.

6.6 Auto mode definition Common Resolution and Audio

Switcher will find highest common Resolution and Audio from all destination EDID to link Source.

Example for single source

Destination > press #1 and then Source > press #1

Destination device #1 will set to the highest common resolution and Audio of source #1

Example for multiple sources

Destination device #1, #2, #3 will be set to the highest common resolution and Audio available and source device #1 will output this same resolution.


PAGE 11

FRONT PANEL

FRONT PANEL

POWER

OUTPUT : 1 2 3 4

INPUT : 2 4 1 3

SB-5645


IR

AL L OF F ED ID

SOURCE STATUS

1 2 3 4

LO CK RECALL MEMORY ENTER

1

DESTINATION

1

SOURCE

2 3

2 3

4

4

DESTINATION

SOURCE

1 3 8 6 2 7 5 4

1

2

POWER SWITCH

The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power.

The Switcher will remember that last state during a power cycle.

When power is removed and resorted, the last configuration will be evoked.

INPUT STATUS DISPLAY

Input sources 1 to 4 LCM illuminates blue to indicate that a video source is present on that input.

3 OUTPUT STATUS DISPLAY

Each Output (destination ) Channel shows which input (source) is assigned.

4 DESTINATION SELECT BUTTONS

Separate outputs 1 thru 4 select buttons are provided for each destination assignment.

Routing can be Source to Destination or one source to multiple destinations.

Example : Press Destination 1,2,4 then press Source 2 will route Input 2 to Output 1,2,4 respectfully.

5 EDID MODE SELECT BUTTONS

Used to select EDID mode using Input buttons #1 and #2.

6 IR SENSOR

The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.

7 SOURCE SELECT BUTTONS

Separate inputs 1 thru 4 select buttons are provided each source selection.

8 FUNCTION KEY - ALL

Disables (mute) video on all destinations OR Selects the same source to all destinations.

Option 1

- Press ALL followed by OFF button. The display will show " 0 " indicating all destinations have no video selected.

Option 2

- Press ALL followed by Source 1 thru 4. The display will show the Source selected.

- Press ENTER The pre-set source selection will be assigned all destinations.

PAGE 12


FRONT PANEL

FRONT PANEL

POWER

OUTPUT : 1 2 3 4

INPUT : 2 4 1 3

SB-5645


IR

AL L OF F ED ID

1

SOURCE STATUS

2 3 4


1

DESTINATION

1

SOURCE

2 3

2 3

4

4

DESTINATION

SOURCE

9 10 11

9 FUNCTION KEY - OFF

Disables (mute) video to selected channels. Either destinations.

- Press OFF button followed by any Destination channel.

- Press 1 thru 4 output destination. The display will show " 0 " for the selected

channel indicating no video selected.

10 FUNCTION KEY - RECALL

The system will show previously stored presets, up to a total of 8.

Presets are stored in local memory using Source keys 1 thru 4 or Destination keys 1 thru 4 as the memory preset location.

- press RECALL button.

- press 1 thru 4 on either Source or Destination row.

- press ENTER The pre-set configuration will execute.

Operation completes.

Note: Operation will abort if no keys are dressed within 5 seconds.

11 FUNCTION KEY - ENTER

Press ENTER to confirm entries.


PAGE 13

FRONT PANEL

FRONT PANEL

POWER

OUTPUT : 1 2 3 4

INPUT : 2 4 1 3

SB-5645


IR

AL L OF F ED ID

SOURCE STATUS

1 2 3 4


1

DESTINATION

1

SOURCE

2 3

2 3

4

4

DESTINATION

SOURCE

14 13 12 15

12 FUNCTION KEY - MEMORY

The system will show store presets, up to a total of 8.

Presets are stored in local memory using Source keys 1 thru 4 or Destination keys 1 thru 4 as the memory preset location.

- Configure desired matrices..

- Press MEMORY button.

- Press 1 thru 4 on either Source or Destination row.

- Press ENTER to ready memory location.

- or press MEMORY again to cancel operation.

Operation completes.

Note : Operation will abort if no keys are pressed within 5 seconds.

13 FUNCTION KEY - LOCK

- Press and hold LOCK button for two seconds lockout the front panel.

- Press and hold LOCK button for two seconds to enable the front panel.

14 FUNCTION KEY - EDID

- press EDID to select new EDID mode or select source row #1 or #2 for LINK source EDID again.

15 19 INCH EAR MOUNT PAIR

Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED.

Image shows rack mount bracket attached.

PAGE 14


REAR PANEL

REAR PANEL

OUTPUT

4

OUTPUT

3

OUTPUT

2

OUTPUT

1

INPUT

4

INPUT

3

INPUT

2

INPUT

1


RS232 IR EXT.

RoHS

RoHS/9 5/EC

INPUT

DC 12V

6

1 DC POWER INLET

The Switcher is fitted with a DC power plug input connector.

Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 3A Max (Center pin positive).

2 IR EXTENDER CONTROL

Support one of IR Extender

Extend distance maximum 300Meters / ~1000 feet

When you plug the External IR extender into the switcher, the front panel IR receiver remain active.

3 RS 232 CONNECTION

RS 232 control port to allow for interfacing to a PC , Such as a computer or touch panel control, to the switcher via this

DB-9pin Female connector for serial RS-232 control.

4 INPUTS- 1,2,3, & 4 HDMI

Connect a signal link of HDMI direct digital video/audio to this Female HDMI connector. This connector supports HDMI digital video/audio and DVI digital video sources.

HDMI Digital Video/Audio, Connector with fix screw

Input 1 ~ Input 4

5 OUTPUTS- 1,2,3,& 4 HDMI

Connect a signal link of HDMI direct digital video/audio to this Female HDMI connector. This connector supports HDMI digital video/audio and DVI digital video sources.

HDMI Digital Video/Audio, Connector with fix screw

Output 1 ~ Output 4

4 3 2 1

Power Jack:

DC Jack - inner OD O 2.1mm (+ )

Outside OD O 5.5mm (GND)

Power input - 12VDC, 3A

IR Extender Jack:

Female Jack - inner OD O 3.5 mm

Remote port :

DB-9pin Female connector

HDMI digital video/audio connector:

HDMI Female connector.

Note:

With the proper adapters, the switcher can be used with DVI digital video signals

HDCP compliant. DVI does not support audio.

HDMI digital video/audio connector:

HDMI Female connector.

Note:

With the proper adapters, the switcher can be used with DVI digital video signals

HDCP compliant.


PAGE 15

TYPICAL APPLICATION

INSTALLING DIAGRAM 4x4 HDMI MATRIX SWITCHER

Sample connection using IR Transmitters (SB-101) and IR Receiver (SB-100) with SB-6335T & SB-6335R to control a projector.

HDMI Projector

SB-101

IR-Transmitter

To Projector

IR Extender Cable

SB-6335R

HDMI out IR out

HDMI Extender-RX

NOTE:

1. Control Projector Over CAT5e/6/7 Extender:

SB-6335 HDMI CAT5e/6/7 Transmitter

SB-6335R HDMI CAT5e/6/7 Receiver

2. Preview Output : Picture as same OUTPUT-1

3. RS-232 Control

4. External IR Remote.

5. IR Extender Transmitter :

SB-101 IR Extender Transmitter.

6. IR Extender Receiver :

SB-100 IR Extender Receiver.

CAT5e/6/7 Extension Cable Limited to 330 feet (100M)

OUTPUT

4

OUTPUT

3

OUTPUT

2

OUTPUT

1

INPUT

4

INPUT

3

INPUT

2

INPUT

1


RoHS

RoHS/9 5/EC

RS232 IR EXT.

SB-6335T HDMI in

Extender-Transmitter

CAT5 out

IR in

SB-100

IR-Receiver

IR Extender Cable

Blu-ray

IR Extender Cable

SB-100

IR-Receiver

SB-5688 IR

PC RS232 Control

Projector Remote Control

Support HDBaseT Extender by SB-6335 Transmitter and SB-6335R Receiver via CAT5e/6/7 cable

PAGE 16


TYPICAL APPLICATION

INSTALLING DIAGRAM 4x4 HDMI MATRIX SWITCHER

Sample connection using IR Transmitters (SB-101) and IR Receivers (SB-100) with SB-6335T and SB-6335R to control a Satellite Receiver.

NOTE :

1. Control Satellite Receiver Over HDMI

CAT5e/6/7 Extender from room:

SB-6335T HDMI CAT5e/6/7 Transmitter

SB-6335R HDMI CAT5e/6/7 Receiver

2. Audio Extractor To Recode Audio :

SB-5609 HDMI Audio Extractor.

3. Control HDMI ARC:

SB-5610 ARC Control Box.

4. IR Extender Transmitter :

SB-101 IR Extender Transmitter.

5. IR Extender Receiver :

SB-100 IR Extender Receiver.

SB-6335R

Extender-Receiver

CAT5 in HDMI out

SB-5609

ARC

IR in

Audio Extractor

IR Extender Cable

SB-100

IR-Receiver

Audio Amplifier

AUDIO AMPLIF IE R

Audio Mixer

Satellite Receiver Remote Control

CAT5e/6/7 Extension Cable Limited to 330 feet (100M)

OUTPUT

4

OUTPUT

3

OUTPUT

2

OUTPUT

1

INPUT

4

INPUT

3

INPUT

2

INPUT

1


RS232

IR EXT.

RoHS

RoHS/9 5/EC

INPUT

DC 12V

HDMI output to SB-5610

ARC Device

ARC TV

HDMI DISPLA

Y

HDMI in

SB-6335T

Extender-Transmitter

IR out

IR Extender Cable

CAT5 out

SB-5610

ARC

ARC Control Box

SB-101

IR Signal from Satellite

Receiver Remote Control

HD Satellite Receiver

Support HDBaseT Extender by SB-6335 Transmitter and SB-6335R Receiver via CAT5e/6/7 cable

SB-5645 INSTRUCTION & OPERATION MANUAL PAGE 17

REMOTE CONTROL

Before making any connections to the switcher. Observe the following:

> Ensure the mains voltage supply matches the label on the supplied plug-

Pack (+/- 10%)

> Ensure that the power switch is OFF

> Ensure that all system grounds (earth) are connected to a common point.

> Avoid powering equipment within a system from multiple power sources that may be separated by large distances

REMOTE CONTROL

> Connect all audio video sources and destination equipment

> power up all source and destination audio-visual sources

> For each destination output select the appropriate input source by using

The front panel input 1~8 select buttons. The supplied IR remote control.

Or through the RS 232 serial communications port.

> Upon power up the switcher will return to its last used setting before

Powered down.

IR REMOTE : SW-5645

IR REMOTE CONTROL KEY :

1

10EF

2

20DF

ON

3

POWER

A15E A25D

30CF

DESTINATION

OFF

4

40BF

1

01FE

2

02FD

3

03FC

SOURCE

4

04FB

ALL

B04F

OFF

B14E

EDID

B748

LOCK

B54A

RECALL MEMORY ENTER

B24D B44B B34C


SW-5645

ENIRPA5645000A2

1

2

3

4

6

5

1 2 SWITCH POWER ON or OFF

Controller with a separate power ON and OFF

3 DESTINATION : 1 thru 4 OUTPUT SELECTION

Press the destination button to select the output display channel.

4

5

SOURCE : 1 thru 4 INPUT SOURCE SELECTION

Press input 1~4 sources with selection button

FUNCTION KEY

ALL - function selection button

DEMO or ENTER - function selection button

EDID - function selection button

LOCK - function selection button

6 SELECT EDID MODES : press source button 1 thru 2.

1 Mode 1 : FSS (Fast Speed Start)

2 Mode 2 : H24-3D

3 Mode 3 : H24M-3D

4 Mode 4 : H36

5 Mode 5 : H36M

6 Mode 6 : H36-3D

7 Mode 7 : H36M-3D

8 Mode 8 : AUTO

PAGE 18


REMOTE CONTROL

IR REMOTE CUSTOM AND DATA CODES (NEC Standard)

HOW TO SETUP IR CODES :

CUSTOM CODE : 1C E3

DATA CODE :

POWER ON : 1CE3 A15E

POWER OFF : 1CE3 A25D

ALL

OFF

EDID

LOCK

RECALL

MEMORY

ENTER

: 1CE3 B04F

: 1CE3 B14E

: 1CE3 B748

: 1CE3 B54A

: 1CE3 B24D

: 1CE3 B44B

: 1CE3 B34C

PRESS TV DESTINATION - # then PRES AV SOURCE - #

DESTINATION #1 : 1CE3 10EF

DESTINATION #2 :

DESTINATION #3 :

DESTINATION #4 :

SOURCE #1 : 1CE3

SOURCE #2 :

SOURCE #3 :

1CE3

1CE3

SOURCE #4 : 1CE3

1CE3

1CE3

1CE3

01FE

02FD

03FC

04FB

20DF

30CF

40BF

For example;

Select Destination # 1 to show Source #1~4,

The IR Data Code list :

Destination # 1 , Source #1




1CE3

1CE3

1CE3

1CE3

10EF

10EF

10EF

10EF

1CE3

1CE3

1CE3

1CE3

01FE

02FD

03FC

04FB

Press EDID Mode key :

Mode 1 : FSS

Mode 2 : H24-3D

Mode 3 : H24M-3D

Mode 4 : H36

Mode 5 : H36M

Mode 6 : H36-3D

Mode 7 : H36M-3D

Mode 8 : AUTO

: 1CE3

: 1CE3

: 1CE3

: 1CE3

: 1CE3

: 1CE3

: 1CE3

: 1CE3

E01F

E11E

E21D

E31C

E41B

E51A

E619

E718


PAGE 19

IR EXTENDER

REAR PANEL IR EXTENDER PORT

RS - 232 IR EXT.

RoHS/95/EC

INPUT

DC 12V

DISTANCE maximum 300 M / ~ 1000 feet

SHINYBOW SB-5645

IR Extender to a Room

IR part number : SW-5645

IR Receiver : SB-100 (included)

IR EXTENDER CONNECTION

ROO M

SB-100

SB-100

1

ON

1

POW ER

OFF

2 3

IN PU T -1

4

1 2 3

IN PU T -2

4

1 2 3

IN PU T -3

4

1 2 3

IN PU T -4

4:4 HDM I MATR IX SW

SW-5645p

4

IR

*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***

IR EXTENDER PACKAGE :

HOW TO SETUP THE IR EXTENDER COMPONENTS

Step 1

Tip:Signal

Ring:VCC

Sleeve:GND

Tip

Ring

Ring Sleeve

Sleeve Tip (center)

Step 2

Cable

Step 3

VCC

Sol der

GND

Signal

GND

VCC

Signal

Cable

Switcher IR EXT. In

RoHS/95/EC

INPUT

DC 12V

RS - 232 IR EXT.

IR Receiver (SB-100)

Cable

PAGE 20


CONSUMER ELECTRONICS CONTROL (CEC)

CONSUMER ELECTRONIC CONTROL (CEC)

In brief, CEC allows HDMI devices to control each other when necessary and allows the user to operate multiple devices with one remote control handset.

To Enable CEC

- Press EDID button

- Press ALL button

- Press EDID button The pre-set configuration will execute.

To Disable CEC

- Press EDID button

- Press OFF button

- Press EDID button The pre-set configuration will execute.

Not all device support CEC. Check with your Users Guide for additional information and specifications.

To ensure stable operation, HDMI connections should only be made with switcher powered OFF.


PAGE 21

RS-232 SERIAL INTERFACE

RS-232 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION COMPATIBLE V2.0.1

For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual.

1 2 3 4 5

6 7 8 9

RS-232 SERIAL INTERFACE

Pin RS-232 Definition

1 ------ Not used

2 TX Transmitter

3 RX Receiver

4 ------ Not used

5 GND Ground

6 ------ Not used

7 ------ Not used

8 ------ Not used

9 ------ Not used

RS-232 PROTOCOL COMMANDS ( RS232 Control driver V2.0.1 )

The Shinybow switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system.

The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1.

When the unit recognises a complete command it will perform the requested action - there is no delimiter character required.

PAGE 22


LIMITED WARRANTY

LIMITED WARRANTY

SHINYBOW WARRANTY

SHINYBOW Technology warrants this product against defects in materials and workman ship for a period of 3 years from the date of purchase.

Should this product, in SHINYBOW Technology's opinion, Prove defective within this warranty period, SHINYBOW Technology, at its option, will repair this product without charge, to whatever extent it shall deem necessary to restore said product to proper operation condition. This does not extend the warranty period.

This warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, and abnormal operating condition or non-SHINYBOW

Technology authorized modification to the product.

If repairs are necessary under the warranty policy, the original purchaser must return the product to local distributor, freight prepaid.

After repairs are complete, the product will be returned.

REGULATORY COMPLIANCE

The product complies with the relevant standards for CE, FCC and RoHS approval.

The power Adaptor/Supply has been tested for compliance with UL.CSA and CE standards.

TROUBLESHOOTING

If you experience a <no signal> with this switcher or distributor outputs, first make certain that the signal being fed to its inputs is acceptable.

Disconnect the cables from the this switcher or distributor inputs and connect them directly to an appropriate monitoring device, if you do not see or hear a signal the problem may well be he signal source itself. Also check that the AC outlet you have used to power the switcher or distributor is actually providing power as a wall switch often controls an AC outlet.

The second most common problem with this switcher or distributor revolves around the cables,

Inspect the cables for loose connectors or cable damage such as crushed cable or cables with cuts or nicks. Replace any cable exhibiting these problem.

You also must use the highest quality cables if you want to achieve the best results. Poor quality cables provide will poor quality signals.

M U LT I M E D I A A U D I O A N D V I S U A L

1399 Wildfi re Lane | Frisco, TX 75034

1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 [email protected]

www.shinybow

usa

.com

Shinybow USA SB-5645 Instruction manual

In st ru ction Manual

MODEL : SB-5645

4x4 HDMI MATRIX SWITCHER

HDMI Matrix Switcher Series

SAFETY INFORMATION

TABLE OF CONTENTS

PAGE 3

INTRODUCTION AND PACKAGE CONTENTS

PAGE 4

INTRODUCTION AND PACKAGE CONTENTS

PAGE 5

SPECIFICATIONS

PAGE 6

EDID FUNCTION

PAGE 7

EDID FUNCTION

PAGE 8

EDID FUNCTION

PAGE 9

EDID FUNCTION

PAGE 10

EDID FUNCTION

PAGE 11

FRONT PANEL

PAGE 12

FRONT PANEL

PAGE 13

FRONT PANEL

PAGE 14

REAR PANEL

PAGE 15

TYPICAL APPLICATION

PAGE 16

TYPICAL APPLICATION

ARC TV

SB-5645 INSTRUCTION & OPERATION MANUAL PAGE 17

REMOTE CONTROL

PAGE 18

REMOTE CONTROL

HOW TO SETUP IR CODES :

DATA CODE :

PRESS TV DESTINATION - # then PRES AV SOURCE - #

For example;

Select Destination # 1 to show Source #1~4,

The IR Data Code list :

Destination # 1 , Source #1

Destination # 1 , Source #2

Destination # 1 , Source #3

Destination # 1 , Source #4

10EF

10EF

10EF

10EF

Press EDID Mode key :

PAGE 19

IR EXTENDER

IR EXTENDER PACKAGE :

Step 1

Step 2

Step 3

PAGE 20

CONSUMER ELECTRONICS CONTROL (CEC)

PAGE 21

RS-232 SERIAL INTERFACE

PAGE 22

LIMITED WARRANTY

LIMITED WARRANTY

www.shinybow

.com

Related manuals

Shinybow USA

SB-5645

Shinybow USA

SB-5645

Shinybow USA

SB-5688

Shinybow USA

SB-5642LCM

KVMSwitchTech